SPLIT-TYPE AIR CONDITIONERS
INDOOR UNIT
MSZ-FD25VA MSZ-FD35VA
MSZ-FD25VAS MSZ-FD35VAS
SG79F181H01_Cover-3.indd 1
For user
OPERATING INSTRUCTIONS
• To use this unit correctly and safely, be sure to read this operating instructions before use.
English
For den Anwender
BEDIENUNGSANLEITUNG
• Um diese Einheit richtig und sicher zu verwenden, unbedingt diese Bedienungsanleitung vor der Inbetriebnahme durchlesen.
Deutsch
A l’attention des clients
NOTICE D’UTILISATION
• Pour avoir la certitude d’utiliser cet appareil correctement et en toute
sécurité, veuillez lire attentivement cette notice d’instructions avant de
mettre l’appareil en fonction.
Français
Voor de klant
BEDIENINGSINSTRUCTIES
• Om dit apparaat op de juiste manier en veilig te gebruiken, dient u eerst
deze gebruiksaanwijzing aandachtig door te lezen.
Nederlands
Para los clientes
MANUAL DE INSTRUCCIONES
• Para emplear correctamente este aparato y por razones de seguridad
debe leer este manual de instrucciones de manejo antes de su utilización.
Español
Per gli utenti
LIBRETTO D’ISTRUZIONI
• Per utilizzare correttamente quest’unità, leggere questo libretto d’istruzioni attentamente e per intero.
Italiano
Για το χρήστη
ΟΔΗΓΙΕΣ ΛΕΙΤΟΥΡΓΙΑΣ
• Για να χρησιμοποιήσετε αυτή την μονάδα σωστά και με ασφάλεια, βεβαιωθείτε ότι έχετε διαβάσει αυτό το εγχειρίδιο οδηγιών πριν από την
χρήση.
Ελληνικά
Para o utilizador
INSTRUÇÕES DE OPERAÇÃO
• Para utilizar esta unidade correctamente, certifique-se de que lê estas
instruções de operação antes da utilização.
Português
Til kunden
BETJENINGSVEJLEDNING
• Læs denne brugsanvisning før brugen så korrekt og forsvarlig anvendelse af klima-anlægget sikres.
Dansk
För användaren
BRUKSANVISNING
• För att använda enheten på rätt och säkert sätt ska denna bruksanvisning läsas innan enheten tas i bruk.
Svenska
Kullanıcı için
ÇALIŞTIRMA TALİMATLARI
• Bu birimi doğru ve güvenli olarak çalıştırmak için, kullanmadan önce bu
işletme talimatlarını mutlaka okuyun.
Türkçe
Для пользователя
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
• Для обеспечения правильного и безопасного использования прибора следует до начала его эксплуатации внимательно прочитать
данное руководство.
Русский
6/12/2007 11:11:45 AM
● OPERATING INSTRUCTIONS ●
CONTENTS
■ SAFETY PRECAUTIONS
■ DISPOSAL
■ NAME OF EACH PART
■ PREPARATION BEFORE OPERATION
■ AREA SETTING
■ SELECTING OPERATION MODES
■ FAN SPEED AND AIRFLOW DIRECTION ADJUSTMENT
■ ECONO COOL OPERATION
■ TIMER OPERATION (ON/OFF TIMER)
■ PLASMA OPERATION
■ CLEAN OPERATION
■ CLEANING
■ WHEN YOU THINK THAT TROUBLE HAS OCCURRED
■ WHEN THE AIR CONDITIONER IS NOT GOING TO BE USED FOR A LONG TIME
■ INSTALLATION PLACE AND ELECTRICAL WORK
■ SPECIFICATIONS
1
2
3
3
4
5
6
7
7
7
7
8
9
10
10
10
SAFETY PRECAUTIONS
• Since rotating parts and parts which could cause an electric shock are used
in this product, be sure to read these “Safety Precautions” before use.
• Since the cautionary items shown here are important for safety, be sure to
observe them.
• After reading this manual, keep it together with the installation manual in a
handy place for easy reference.
Marks and their meanings
WARNING :
Incorrect handling could cause serious hazard, such as
death, serious injury, etc. with a high probability.
CAUTION :
Incorrect handling could cause serious hazard depending
on the conditions.
Meanings of symbols used in this manual
: Be sure not to do.
: Be sure to follow the instruction.
: Never insert your finger or stick, etc.
: Never step onto the indoor/outdoor unit and do not put anything on them.
: Danger of electric shock. Be careful.
: Be sure to disconnect the power supply plug from the power outlet.
: Be sure to shut off the power.
WARNING
Do not connect the power cord to an intermediate point,
use an extension cord, or connect multiple devices to a
single AC outlet.
• This may cause overheating, fire, or electric shock.
Make sure the power plug is free of dirt and insert it securely into the outlet.
• A dirty plug may cause fire or electric shock.
Do not bundle, pull, or modify the power cord, and do not
apply heat or place heavy objects on it.
• This may cause fire or electric shock.
Do not turn the breaker OFF/ON or disconnect/connect the
power plug during operation.
• This may create sparks, which can cause fire.
• After the indoor unit is switched OFF with the remote controller, make sure to turn the breaker OFF or disconnect the
power plug.
Do not expose your body directly to cool air for a prolonged
length of time.
• This could be detrimental to your health.
The unit should not be installed, relocated, or repaired
by the user.
• An improperly handled air conditioner may cause fire or
electric shock.
Do not insert your finger, a stick, or other objects into the
air inlet or outlet.
• This may cause injury, since the fan inside rotates at high
speeds during operation.
In case of an abnormal condition (such as a burning smell),
stop the air conditioner and disconnect the power plug or
turn the breaker OFF.
• A continued operation in the abnormal state may cause a
malfunction, fire, or electric shock. In this case, consult your
dealer.
When the air conditioner does not cool or heat, there is
a possibility of refrigerant leakage. In this case, consult
your dealer. If a repair involves recharging the unit with
refrigerant, ask the service technician for details.
• The refrigerant used in the air conditioner is safe. Normally,
it does not leak. However, if refrigerant leaks and comes in
contact with a heat source such as a fan heater, kerosene
heater, or cooking stove, it will create a harmful gas.
CAUTION
Do not touch the air inlet or the aluminum fins of the
indoor/outdoor unit.
• This may cause injury.
Do not use insecticides or flammable sprays on the unit.
• This may cause a fire or deformation of the unit.
Do not expose pets or houseplants to direct airflow.
• This may cause injury to the pets or plants.
Do not place other electric appliances or furniture under
the indoor/outdoor unit.
• Water may drip down from the unit, which may cause damage
or malfunction.
Do not leave the unit on a damaged installation stand.
• The unit may fall and cause injury.
En-1
SG79F181H01.indd 1
6/13/2007 2:05:50 PM
SAFETY PRECAUTIONS
CAUTION
Do not operate switches with wet hands.
• This may cause electric shock.
Do not step on an unstable bench to operate or clean the
unit.
• This may cause injury if you fall down.
Do not clean the air conditioner with water or place an object
that contains water, such as a flower vase, on it.
• This may cause fire or electric shock.
Do not pull the power cord.
• This may cause a portion of the core wire to break, which may
cause overheating or fire.
Do not step on or place any object on the outdoor unit.
• This may cause injury if you or the object falls down.
Do not charge or disassemble the batteries, and do not
throw them into a fire.
• This may cause the batteries to leak, or cause a fire or explosion.
Do not operate the unit for a long time at high humidity (80%
RH or more), such as with a door or window left open.
• The water condensation in the air conditioner may drip down,
wetting or damaging the furniture.
Do not use the unit for special purposes, such as storing
food, raising animals, growing plants, or preserving precision devices or art objects.
• This may cause deterioration of quality, or harm to animals
and plants.
Do not expose combustion appliances to direct airflow.
• This may cause incomplete combustion.
Before cleaning the unit, switch it OFF and disconnect the
power plug or turn the breaker OFF.
• This may cause injury, since the fan inside rotates at high
speeds during operation.
When the unit will be unused for a long time, disconnect the
power plug or turn the breaker OFF.
• The unit may accumulate dirt, which may cause overheating
or fire.
Replace all batteries of the remote controller with new ones
of the same type.
• Using an old battery together with a new one may cause
overheating, leakage, or explosion.
If the battery fluid comes in contact with your skin or clothes,
wash them thoroughly with clean water.
• If the battery fluid comes in contact with your eyes, wash them
thoroughly with clean water and immediately seek medical
attention.
Ensure that the area is well-ventilated when the unit is operated together with a combustion appliance.
• Inadequate ventilation may cause oxygen starvation.
For installation
WARNING
Consult your dealer for installing the air conditioner.
• It should not be installed by the user since installation requires
specialized knowledge and skills. An improperly installed air
conditioner may cause water leakage, fire, or electric shock.
Provide a dedicated power supply for the air conditioner.
• A non-dedicated power supply may cause overheating or
fire.
Do not install the unit where flammable gas could leak.
• If gas leaks and accumulates around the outdoor unit, it may
cause an explosion.
Earth the unit correctly.
• Do not connect the earth wire to a gas pipe, water pipe, lightning rod, or a telephone ground wire. Improper earthing may
cause electric shock.
CAUTION
Install an earth leakage breaker depending on the installation location of the air conditioner (such as highly humid
areas).
• If an earth leakage breaker is not installed, it may cause electric
shock.
Ensure that the drain water is properly drained.
• If the drain passage is improper, water may drip down from
the indoor/outdoor unit, wetting and damaging the furniture.
In case of an abnormal condition
Immediately stop operating the air conditioner and consult your dealer.
Turn the breaker OFF when you hear thunder and there is a
possibility of a lightning strike.
• The unit may be damaged if lightning strikes.
After the air conditioner is used for several seasons, perform inspection and maintenance in addition to normal
cleaning.
• Dirt or dust in the unit may create an unpleasant odor or clog
the drain passage, and cause water to leak from the indoor
unit. Consult your dealer for inspection and maintenance,
which require specialized knowledge and skills.
DISPOSAL
To dispose of this product, consult your dealer.
Note:
This symbol mark is for EU countries only.
This symbol mark is according to the directive 2002/96/
EC Article 10 Information for users and Annex IV.
Your MITSUBISHI ELECTRIC product is designed and manufactured with high
quality materials and components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their end-of-life,
should be disposed of separately from your household waste.
Please, dispose of this equipment at your local community waste collection/recycling center.
In the European Union there are separate collection systems for used electrical
and electronic product.
Please, help us to conserve the environment we live in!
En-2
SG79F181H01.indd 2
6/13/2007 2:05:51 PM
● OPERATING INSTRUCTIONS ●
NAME OF EACH PART
Indoor unit
Remote controller
Signal transmitting
section
Distance of signal :
About 6 m
Display section
Beep(s) is (are) heard
from the indoor unit when
the signal is received.
Remote control
receiving section
Operation
indicator
lamp
Operation display
section
Front panel
ON/OFF
(operate/stop)
button
Air filter
Temperature buttons
Operation select
button Page 5
FAN speed
control button
Air inlet
Plasma
deodorizing
filter
Plasma electrode unit
Page 5
Off-timer button Page 7
Page 6
On-timer button Page 7
ECONO COOL
button Page 7
PLASMA button
Page 7
Plasma
anti-allergy
enzyme filter
Air outlet
WIDE VANE
button Page 6
TIME set buttons Pages 3, 7
Increase time
Decrease time
AREA button Page 4
CLOCK button Page 3
RESET button Page 3
Page 7
VANE
control button
i-see sensor Page 4
Page 6
Fan guard
Fan
Horizontal vane
Heat
exchanger
Vertical vane
CLEAN button
Emergency
operation
switch Page 5
Page 7
Lid
Slide down
to open
i-see button Page 4
Remote controller
holder
Outdoor unit
Air inlet (back and side)
Piping
Drainage hose
• Install the remote controller holder to a place where
the signal can be received
by the indoor unit.
Air outlet
Drain outlet
Appearance of the outdoor unit may differ from some models.
Use the remote controller provided with the unit only.
Do not use other remote controllers.
PREPARATION BEFORE OPERATION
Before operation: Insert the power supply plug into the power outlet and/or turn the breaker on.
Installing the remote controller batteries
Be sure to set the installation position before installing the batteries. Page 4
1.
1.
Press RESET
2.
Press CLOCK
Remove the front lid
2.
3.
•
•
•
•
•
Setting current time
Insert AAA
alkaline batteries
Install the front lid
Make sure the polarity of the batteries is correct.
Do not use manganese batteries. The remote controller could malfunction.
Do not use rechargeable batteries.
Replace all batteries with new ones of the same type.
Batteries can be used for approximately 1 year. However, batteries with
expired shelf lives last shorter.
3.
4.
Press CLOCK again
Press the TIME buttons to set the
time.
Each press increases/decreases
the time by 1 minute (10 minutes
when pressed longer)
• Press RESET and CLOCK gently using a thin
stick.
If the RESET button is not pressed, the remote
controller may not operate correctly.
En-3
SG79F181H01.indd 3
6/13/2007 2:05:54 PM
PREPARATION
AREA SETTING
BEFORE OPERATION
Setting the installation position
Be sure to set the slide switch inside the remote controller in accordance with
the installed position of the indoor unit.
Installation position:
Left:
Distance to objects (wall, cabinet, etc.) is less than 50 cm to the left
Center: Distance to objects (wall, cabinet, etc.) is more than 50 cm to the left
and right
Right: Distance to objects (wall, cabinet, etc.) is less than 50 cm to the right
(Left)
(Center)
Area
Slide switch
(Right)
Left
Slide switch
Center
Right
Remote controller
display
Press
during COOL mode to activate i-see control
operation.
Press
to select AREA. Each press changes
AREA in the following order:
• Press gently using a thin stick.
•
lights. (Operation display section)
(AUTO)
(Left)
(Right)
Cancel
*1
• The i-see control operation has to be active to select AREA.
Press
again to release i-see control operation.
• Horizontal airflow direction
cannot be selected when AREA is
set.
*1 Horizontal airflow direction set by
. Page 6
Press
setting.
i-see control operation
• Pressing
The sensors constantly measure the room and
floor/wall temperature to automatically adjust to
the set temperature by estimating the temperature actually perceived by a person inside the
room (“sensible temperature”).
Room
temperature
30.9%
Floor/wall
temperature
43.7%
Humidity
20.7%
until “Cancel” is selected to release AREA
also releases AREA setting.
Area
(AUTO) ....The i-see sensor detects temperature disparities, efficiently
cooling the whole room.
In COOL mode:
Daytime
Warm area
Nighttime
Cold area
i-see sensor
When the AREA setting is not activated, the sensing range of the move eye sensor
differs depending on the installation location of the air conditioner.
Installation position
Sensing range
Note:
Left
Center
Right
Do not touch the i-see sensor. This may cause malfunction of the i-see sensor.
(LEFT) /
(RIGHT)
Select the desired area to be air conditioned.
Indoor unit display
Horizontal airflow direction:
Left
Center or Swing
Right
Lighted
Not ligted
En-4
SG79F181H01.indd 4
6/13/2007 2:05:58 PM
● OPERATING INSTRUCTIONS ●
SELECTING OPERATION MODES
AUTO mode (Auto changeover)
The unit selects the operation mode according to the difference between the
room temperature and the set temperature. During AUTO mode, the unit
changes mode (COOL↔HEAT) when the room temperature is 2°C away
from the set temperature for more than 15 minutes.
Note:
During multi system operation, the unit may not be able to switch operation mode between COOL and HEAT. In this case, the indoor unit becomes standby mode.
COOL mode
Enjoy cool air at your desired temperature.
Do not operate COOL mode at low outside temperature (less than -10°C).
Water condensed in the unit may drip and wet or damage furniture, etc.
DRY mode
Dehumidify your room. The room may be cooled slightly.
Temperature cannot be set during DRY mode.
HEAT mode
Enjoy warm air at your desired temperature.
1
2
Press
When the remote controller cannot be used...
Emergency operation can be activated by pressing the emergency operation
switch (E.O.SW) on the indoor unit.
Press
to select operation mode. Each press
changes mode in the following order:
(AUTO)
3
Emergency operation
to start the operation.
(COOL)
(DRY)
Each time the E.O.SW is pressed, the operation changes in
the following order:
(HEAT)
Operation indicator lamp
Emergency COOL
Press
or
to set the temperature.
Each press raises or lowers the temperature by 1°C.
Emergency HEAT
Press
to stop the operation.
• The same setting is selected the next time by simply pressing
Stop
.
Set temperature : 24°C
Fan speed : Medium
Horizontal vane : Auto
Note:
The first 30 minutes of operation is test run. Temperature
control does not work, and fan speed is set to High.
Auto restart function
If a power failure occurs or the main power is turned off during operation, “Auto
restart function” automatically starts operation in the same mode as the one set
with the remote controller just before the shutoff of the main power. When
timer is set, timer setting is cancelled and the unit starts operation when power
is resumed.
If you do not want to use this function, please consult the service representative because the setting of the unit needs to be changed.
Multi system operation
Two or more indoor units can be operated by one outdoor unit. When several
indoor units are operated simultaneously, cooling and heating operations cannot be done at the same time. When COOL is selected with one unit and HEAT
with another or vice versa, the unit operated later becomes standby mode. The
power lamp blinks (display section).
En-5
SG79F181H01.indd 5
6/13/2007 2:06:00 PM
FAN SPEED AND AIRFLOW DIRECTION ADJUSTMENT
Vertical airflow direction
(AUTO)
The vane is set to the most efficient airflow direction. COOL/DRY:horizontal
position. HEAT:downward position.
(Manual)
For efficient air conditioning, select upper position for COOL/DRY, and lower
position for HEAT. During COOL/DRY, when the vane is set to position (4)
or (5), the vane automatically moves to horizontal position after 1 hour to
prevent water dripping.
(Swing)
The vane moves up and down intermittently.
Press
to select fan speed. Each press changes
fan speed in the following order:
(AUTO)
(Low)
(Med.)
(High) (Super High)
• Two short beeps are heard from the indoor unit when set to AUTO.
• Use the
(Super High) notch to cool/heat the room more efficiently.
• If the operating sound of the air conditioner disturbs your sleep, use the
(Low) notch.
Press
to select vertical airflow direction. Each
press changes airflow direction in the following order:
(AUTO)
(1)
(2)
(3)
(4)
(5)
(SWING)
• Two short beeps are heard from the indoor unit when set to AUTO.
Press
to select horizontal airflow direction. Each
press changes airflow direction in the following order:
(SWING)
En-6
SG79F181H01.indd 6
6/13/2007 2:06:03 PM
● OPERATING INSTRUCTIONS ●
ECONO COOL OPERATION
Press
during COOL mode page 5 to start
ECONO COOL operation.
The unit performs swing operation vertically in various cycle according
to the temperature of the unit. Set temperature is set 2°C higher automatically.
Press
again to cancel ECONO COOL operation.
• Pressing
also cancels ECONO COOL operation.
What is “ECONO COOL”?
Swing air flow (change of air flow) makes you feel cooler than constant air flow.
So, even though the set temperature is automatically set 2°C higher, it is possible to perform cooling operation with keeping comfort. As a result, energy can
be saved.
TIMER OPERATION (ON/OFF TIMER)
1
Press
or
during operation to set the timer.
(ON timer) : The unit turns ON at the set
time.
(OFF timer) : The unit turns OFF at the set
time.
*
or
blinks.
* Make sure that the current time is set correctly. Page 3
2
Press
(Increase) and
time of timer.
(Decrease) to set the
Each press increases or decreases the set time by 10 minutes.
3
Press
or
again to cancel timer.
Note:
PLASMA OPERATION
Press
to start PLASMA operation.
Press
again to cancel PLASMA operation.
• PLASMA lamp turns on. (Display section)
What is “PLASMA operation”?
Plasma operation consists of deodorizing and air purifying features.
Particles of odor-releasing substances are absorbed and decomposed by the
plasma deodorizing filter. Particles of allergens such as pollens and house dust
are collected by the plasma anti-allergy filter. These filters work with negative
ions generated by the plasma electrode unit.
CLEAN OPERATION
Press
to activate CLEAN operation.
• The unit performs CLEAN operation when it is stopped with the
button or OFF timer after COOL/DRY operation. CLEAN lamp turns
on. (Display section)
• CLEAN operation is not performed when: COOL is operated less than
3 minutes/ DRY is operated less than 6 minutes.
Press
• Pressing
again to deactivate CLEAN operation.
does not deactivate CLEAN operation.
What is “CLEAN operation”?
CLEAN operation function helps to keep the unit clean and prevents mold growth
by generating small amount of ozone (*1) and performing FAN operation for about
40 minutes. It is recommended to keep CLEAN operation active at all times.
*1
About 0.01 ppm at the air outlet. This is the same level found in nature, such
as in forests, and there is no effect on the human body.
Note:
• Fan is stopped for the first 15 minutes of CLEAN operation.
• During multi system operation, air from the unit may become warm. In this
case, CLEAN operation is cancelled automatically to prevent undesirable
rise in room temperature.
• ON and OFF timers can be used in combination. mark indicates the order
of timer operations.
• If power failure occurs while ON/OFF timer is set, see page 5 “Auto restart
function”.
En-7
SG79F181H01.indd 7
6/13/2007 2:06:07 PM
CLEANING
Instructions:
• Use only diluted mild detergents.
• Do not expose parts to direct sunlight, heat, or flames to dry.
• Do not use water hotter than 50°C.
• Switch off the power supply or turn off the breaker before cleaning.
• Be careful not to touch the metal parts with your hands.
• Do not use benzine, thinner, polishing powder, or insecticide.
Heat exchanger
• Wear gloves to protect your hands.
• Use the QUICK CLEAN KIT
(option).
Parts Number MAC-093SS-E
• Refer to the instructions described in
the QUICK CLEAN KIT for details.
Plasma anti-allergy enzyme filter
Every 3 months:
• Remove dirt by a vacuum cleaner.
When dirt cannot be removed by vacuum cleaning:
• Soak the filter together with its frame in lukewarm water and wash it.
• After washing, dry it well in shade and put it back to its original position.
Every year:
• Replace it with a new air cleaning filter for best performance.
• Parts Number MAC-417FT-E
Air filter
• Clean every 2 weeks
• Remove dirt by a vacuum cleaner,
or wash with water.
• Dry it well in shade before installing it.
i-see sensor
Do not touch the i-see
sensor.
Plasma deodorizing filter
Every 3 months:
• Remove dirt by a vacuum cleaner, or soak the filter in lukewarm water
(30 to 40°C) for about 15 minutes. Rinse well.
• After washing, dry it well in shade and put it back to its original position.
• Deodorizing feature recovers by cleaning the filter.
When dirt or smell cannot be removed by cleaning:
• Replace it with a new air cleaning filter.
• Parts Number MAC-307FT-E
Front panel
Hinge
Hole
1. Lift the front panel until a “click” is heard.
2. Hold the hinges and pull to remove as shown in the above illustration.
• Wipe with a soft dry cloth or wash it with water.
• Do not soak it in water for more than two hours.
• Dry it well in shade before installing it.
3. Install the panel by following the removal
procedure in reverse. Close the front panel
securely and press the positions indicated by
the arrows.
Note:
• Clean the filters regularly for best performance and to reduce power
consumption.
• Do not touch the i-see sensor.
Air outlet and Fan (before cleaning, make sure that the fan is stopped)
1
Turn the horizontal vanes downward.
Then, remove the upper vane as
shown in ➀ and ➁.
2
Swing out the two vertical vanes
one by one.
3
Clean the air outlet and fan.
• Wipe with a soft dry cloth.
• Repeat ➀ and ➁ for the lower vane.
Hold the tab
Unlock
4
Clean the fan.
Put the vertical vanes back to
their original positions correctly
one by one, into their respective
guide.
• Push the vanes until they click into place.
5
• Use the QUICK CLEAN KIT (option).
Parts Number MAC-093SS-E
• Refer to the instructions described in the
QUICK CLEAN KIT for details.
Install the horizontal vane by
following the removal procedure
in reverse.
• If the horizontal vane is not installed correctly, all LED lamps blink when power is
turned on.
Note:
Do not apply excessive force to the fan or fan
guard.
Guide
En-8
SG79F181H01.indd 8
6/13/2007 2:06:09 PM
● OPERATING INSTRUCTIONS ●
WHEN YOU THINK THAT TROUBLE HAS OCCURRED
Even if these items are checked, when the unit does not recover from the
trouble, stop using the air conditioner and consult your dealer.
Symptom
Explanation & Check points
Indoor Unit
The unit cannot be operated.
• Is the breaker turned on?
• Is the power supply plug connected?
• Is the ON timer set? Page 7
All LED lamps on the indoor
unit are blinking.
• Are the horizontal vanes installed correctly?
Page 8
The horizontal vane does not
move.
• Are the horizontal vane and the vertical vane
installed correctly? Page 8
• Is the fan guard deformed?
The unit cannot be operated
for about 3 minutes when
restarted.
• This protects the unit according to instructions from the microprocessor. Please
wait.
Symptom
White smoke is discharged
from the outdoor unit.
The display on the remote
controller does not appear
or it is dim. The indoor unit
does not respond to the
remote control signal.
The operation is stopped for
about 10 minutes in the heating operation.
• Defrosting of the outdoor unit is being
done.
Since this is completed in max.10 minutes,
please wait. (When the outside temperature
is too low and humidity is too high, frost is
formed.)
The unit starts operation by
itself when the main power
is turned on, though it isn’t
operated with the remote
controller.
• These models are equipped with an auto restart function. When the main power is turned
off without stopping the unit with the remote
controller and is turned on again, the unit
starts operation automatically in the same
mode as the one set with the remote controller just before the shutoff of the main power.
Refer to “Auto restart function” page 5 .
The operation does not stop,
or air is blown even when the
ON/OFF button is pressed.
• Is the CLEAN lamp lighted? When the
CLEAN lamp is lighted, CLEAN operation
is performed. Page 7
CLEAN lamp is lighted.
• CLEAN operation is performed. Page 7
The room cannot be cooled
or heated sufficiently.
• Is the temperature setting appropriate?
Page 5
• Is the fan setting appropriate? Please
change fan speed to higher setting.
Page 6
• Is the filter clean? Page 8
• Is the fan or heat exchanger of the indoor unit
clean? Page 8
• Are there any obstacles blocking the air inlet
or outlet of the indoor or outdoor unit?
• Is a window or door open?
The room cannot be cooled
sufficiently.
• When a ventilation fan or a gas cooker is
used in a room, the cooling load increases,
resulting in an insufficient cooling effect.
• When the outside temperature is high, the
cooling effect may not be sufficient.
The room cannot be heated
sufficiently.
• When the outside temperature is low, the
heating effect may not be sufficient.
Air does not blow out soon in • Please wait as the unit is preparing to blow
the heating operation.
out warm air.
Airflow
The air from the indoor unit
smells strange.
When heating operation is
selected, operation does not
start right away.
• When operation is started during defrosting
of outdoor unit is done, it takes a few minutes
(max. 10 minutes) to blow out warm air.
Outdoor Unit
The fan of the outdoor unit
• When the outside temperature is low durdoes not rotate even though
ing cooling operation, the fan operates
the compressor is running.
intermittently to maintain sufficient cooling
Even if the fan starts to rotate,
capacity.
it stops soon.
Water leaks from the outdoor
unit.
• During COOL and DRY operations, pipe or
pipe connecting sections are cooled and this
causes water to condense.
• In the heating operation, water condensed
on the heat exchanger drips down.
• In the heating operation, the defrosting operation makes water frozen on the outdoor
unit melt and drip down.
• Is the filter clean? Page 8
• Is the fan or heat exchanger of the indoor unit
clean? Page 8
• The unit may suck in an odor adhering to the
wall, carpet, furniture, cloth, etc. and blow it
out with the air.
• During PLASMA operation, you may smell
ozone that is generated in small quantities
from the plasma electrode unit. This is not a
malfunction.
Sound
Cracking sound is heard.
• This sound is generated by the expansion/
contraction of the front panel, etc. due to
change in temperature.
The sound as burbling is
heard.
• This sound is heard when the outside air is
absorbed from the drain hose by turning on
the range hood or the ventilation fan, making
water flowing in the drain hose to spout out.
This sound is also heard when the outside air
blows into the drain hose in case the outside
wind is strong.
Mechanical sound is heard
from the indoor unit.
• This is the switching sound in turning on/off
the fan or the compressor.
The sound of water flowing
is heard.
• This is the sound of refrigerant or condensed
water flowing in the unit.
Hissing sound is sometimes
heard.
• This is the sound when the flow of refrigerant
inside the unit is switched.
Multi system
The indoor unit which is not
• A small amount of refrigerant continues to
operating becomes warm and
flow into the indoor unit even though it is
a sound, similar to water flownot operating.
ing, is heard from the unit.
• Are the batteries exhausted? Page 3
• Is the polarity (+, -) of the batteries correct?
Page 3
• Are any buttons on the remote controller of
other electric appliances being pressed?
Does not cool or heat
• This is for the swing operation of the HORIZONTAL VANE to be performed normally.
The air flow direction changes • When the unit is operated in COOL or DRY
during operation.
mode, if the operation continues with air
The direction of the horizontal
blowing down for 0.5 to 1 hour, the direction
vane cannot be adjusted with
of the air flow is automatically set to position
the remote controller.
(1) to prevent water from condensing and
dripping.
• In the heating operation, if the air flow temperature is too low or when defrosting is being done, the horizontal vane is automatically
set to horizontal position.
• In the heating operation, vapor generated
by the defrosting operation looks like white
smoke.
Remote controller
Mist is discharged from the air • The cool air from the unit rapidly cools moisoutlet of the indoor unit.
ture in the air inside the room, and it turns
into mist.
The swing operation of the
HORIZONTAL VANE is
suspended for a while, then
restarted.
Explanation & Check points
Outdoor Unit
In the following cases, stop using the air conditioner and consult your dealer.
• When water leaks or drips from the indoor unit.
• When the upper operation indicator lamp blinks.
• When the breaker trips frequently.
• The remote control signal is not received in a room where an electronic ON/OFF
type fluorescent lamp (inverter-type fluorescent lamp, etc.) is used.
• Operation of the air conditioner interferes with radio or TV reception. An amplifier may be required for the affected device.
• When an abnormal sound is heard.
En-9
SG79F181H01.indd 9
6/13/2007 2:06:10 PM
WHEN THE AIR CONDITIONER IS NOT
INSTALLATION PLACE AND
GOING TO BE USED FOR A LONG TIME
1
ELECTRICAL WORK
Installation place
Set to the highest temperature in manual COOL mode,
and operate for 3 to 4 hours. Page 5
Avoid installing the air conditioner in the following places.
• Where there is much machine oil.
• Salty places such as the seaside.
• Where sulfide gas is generated such as a hot spring.
• Where oil is splashed or where the area is filled with oily smoke.
• Where there is high-frequency or wireless equipment.
• Where the air from the outdoor unit air outlet is blocked.
• Where the operation sound or air from the outdoor unit does not bother the
house next door.
This dries the inside of the unit.
2
3
4
Press
to stop the operation.
Turn off the breaker and/or disconnect the power supply plug.
The installation location of the outdoor unit should
be at least 3 m away from the antennas for TV sets,
radios, etc. In areas where the reception is weak,
provide greater space between the outdoor unit and
the antenna of the affected device if operation of the air
conditioner interferes with radio or TV reception.
Remove all batteries from the remote controller.
To prevent the effects
of a fluorescent lamp,
keep as far apart as
possible.
When using the air conditioner again:
1
2
3
Inverter-type
fluorescent lamp
wall, etc.
Keep a space to
prevent the picture distortion or
the noise.
Clean the air filter. Page 8
1m
or more
Check that the air inlet and outlet of the indoor and
outdoor units are not blocked.
Cordless
phone or
Portable
phone
Check that the earth is connected correctly.
Wellventilated dry
place
100 mm or
more
200 mm or
more
TV
1m
or more
3 m or
more
Radio
Electrical work
• Provide an exclusive circuit for the power supply of the air conditioner.
• Be sure to observe the breaker capacity.
If you have any questions, consult your dealer.
SPECIFICATIONS
Model
Indoor
MSZ-FD25VA
MSZ-FD25VA
MSZ-FD35VA
MSZ-FD35VA
Outdoor
MUZ-FD25VA
MUZ-FD25VAH
MUZ-FD35VA
MUZ-FD35VAH
Function
Cooling
Power supply
Heating
Cooling
Heating
Cooling
~ /N, 230 V, 50 Hz
Heating
Cooling
Heating
~ /N, 230 V, 50 Hz
Capacity
kW
2.5
3.2
2.5
3.2
3.5
4.0
3.5
4.0
Input
kW
0.485
0.610
0.485
0.610
0.850
0.865
0.835
0.850
Weight
Indoor
kg
12
Outdoor
kg
36
36
kg
1.15
1.15
Indoor
IP 20
IP 20
Outdoor
IP 24
IP 24
MPa
1.64
1.64
MPa
4.15
4.15
Refrigerant filling capacity (R410A)
IP code
Permissible excessive LP ps
operating pressure
HP ps
Noise level
Indoor (Super High/
High/Med./Low)
dB(A) 42/36/29/20 43/36/29/20 42/36/29/20 43/36/29/20 43/36/29/21 44/36/29/21 43/36/29/21 44/36/29/21
Outdoor
dB(A)
46
Indoor
Heating
47
50
47
50
Note:
Guaranteed operating range
Cooling
12
Outdoor
MUZ-FD25/35VA MUZ-FD25/35VAH
Upper limit
32°C DB
23°C WB
46°C DB
—
46°C DB
—
Lower limit
21°C DB
15°C WB
-10°C DB
—
-10°C DB
—
Upper limit
27°C DB
—
24°C DB
18°C WB
24°C DB
18°C WB
Lower limit
20°C DB
—
-15°C DB
-16°C WB
-20°C DB
-21°C WB
Rating condition
Cooling — Indoor:
Outdoor:
Heating — Indoor:
Outdoor:
27°C DB, 19°C WB
35°C DB
20°C DB
7°C DB, 6°C WB
En-10
SG79F181H01.indd 10
6/13/2007 2:06:11 PM
This product is designed and intended for use in the residential,
commercial and light-industrial environment.
The product at hand is based on the following EU regulations:
• Low Voltage Directive 2006/95/EC
• Electromagnetic Compatibility Directive 89/336/ EEC
HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
SG79F181H01
SG79F181H01_Cover-3.indd 2
6/12/2007 11:11:46 AM