Samsung SVD-4120A Instruction manual

Vandal-Proof Color Dome Camera
INSTRUCTION MANUAL
SVD-4120A /AW
About this manual
Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference.
SALES NETWORK
•
SAMSUNG TECHWIN CO., LTD.
Optics & Digital Imaging Division 145-3, Sangdaewon 1-Dong,
Jungwon-Gu, Sungnam, Kyungki-Do, Korea 462-703
TEL : 82-31-740-8137~41 FAX: 82-31-740-8145
•
SAMSUNG OPTO-ELECTRONICS AMERICA, INC. (SOA)
Closed Circuit Division 40 Seaview Drive, Secaucus NJ 07094,
U.S.A
TEL : (201) 902-0347 FAX: (201) 902-0429
•
SAMSUNG OPTO-ELECTRONICS UK LTD (SOUK)
Samsung House, 1000 Hillswood Drive Hillswood Business
Park Chertsey Surrey KT16 OPS
TEL : 44-(0)1932-45-5308 FAX: 44-(0)1932-45-5325
•
TIANJIN SAMSUNG OPTO-ELECTRONICS CO., LTD (TSOE)
7 Pingchang Rd, Nankai Dist, Tianjin, P.R China
Post Code : 300190
TEL : 86-22-2761-9698 FAX: 86-22-2761-6514
www.samsungtechwin.com
www.samsungcctv.com
P/No. : 6806-0458-01B
VAN 04. 10
SAMSUNG CCTV CAMERA
Thank you for purchasing a SAMSUNG CCTV CAMERA.
Before operating the camera, confirm the camera model and
proper input power voltage. In order that you can understand
this manual thoroughly, we'll introduce our model description.
SVD-4120A Series (410,000 pixels)
• NTSC models
SVD-4120AN
SVD-4120AWN
• PAL models
SVD-4120AP
SVD-4120AWP
Model Description
SVD-4120A X X
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
Signal system
Lens Type
• Lens Type
Blank
2.5X, f=3.8~9.5 Vari-Focal Lens
W
2.4X, f=2.5~6.0 Vari-Focal Lens
• Signal System
N
NTSC Model
P
PAL Model
INFORMATION -This equipment has been tested and found to comply with limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
WARNING - Changes or modifications not expressly approved by the manufacturer
could void the user’s authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
Warning
Features
Fine Picture Condition Under Very
Low Illumination (SENSE UP)
IP66 Approved / Dust and Rain
Resistant
1/3 high density CCD and digital
processor permit high quality pictures to
be captured in very low light condition.
With dust and rain resistant design, the
camera can be installed outside under
building eaves or places that are exposed
to the dust and rain.
High Resolution
SSNR(Samsung Super Noise
Reduction) CHIP
The horizontal resolution of 500TV lines
can be achieved by using a high density
CCD having Double Speed 410,000 pixels
SONY CCD, which provides clean,
noiseless and reliable pictures.
SVD-4120A/AW has an assistant DSP
chip that can remove image noise
efficiently and it shows clean and obvious
image in low luminance
Auto Iris Vari-Focal Lens Built In
Electronic DAY/NIGHT
The focal length of lens is 3.8 to 9.5 mm,
equivalent to 2.5x zoom.(2.5 to 6.0mm,
equivalent to 2.4x zoom/SVD-4120AW)
The built-in lens allows the camera to
have a Wider Dynamic Range, therefore
you can use in various applications.
In normal or high luminance, camera
maintains color mode. On the contrary, it
get changed into B/W mode in low
luminance.
The camera needs periodic inspection.
Contact an authorized technician for inspection.
Stop using your camera when you find a malfunction.
If you use your camera around smoke or unusual heat for a long time, a fire may
be caused.
Do not Install the camera on a surface that can not support it.
Unless the surface is suitable, it could cause falling or other hazards.
Do not hold plug with wet hands.
It could cause an electric shock.
Do not disassemble the camera.
It may result in fire, electric shock or other hazards.
Wide Range ATW
The White Balance can be automatically
adjusted in response to light condition so
that you can observe in an appropriate
color balance.
Do not use the camera close to a gas or oil leak.
It may result in fire or other hazards.
Contents
Precautions
8
Composition
10
Name and Function of Each Section
11
Connection
13
Connecting to Monitor
Connecting to Power
Operating Your Camera
Configuration of The Menu
13
14
15
Setting Up The Menu
• CAMERA ID
• BACKLIGHT
• WHITE BALANCE
• MOTION DETECTION
• IRIS LEVEL CONTROL
• SHUTTER SPEED CONTROL
• SESE UP
• GAIN
• SSNR
• SPECIAL
16
17
20
21
22
25
26
27
28
28
30
Troubleshooting
32
Dimention
34
Specifications
35
15
Precautions
Do not install the camera in
extreme temperature conditions.
Do not install or use the camera in an
environment where the humidity is high.
Only use the camera under conditions
where temperatures are between -10˚C
and +50˚C. Be especially careful to provide
ventilation when operating under high
temperatures.
It can cause the image quality to be poor.
Do not install the camera under
unstable lighting conditions.
Do not drop the camera or
subject them to physical shocks.
It can cause malfunctions to occur.
Never keep the camera face to
strong light directly.
It can damage the CCD.
Do not expose the camera to
radioactivity.
Do not touch the front lens of
the camera.
If it is exposed to radioactivity, For
heated CCD, it will be out of order.
Notes
Severe lighting change or flicker can cause
the camera to work improperly.
COLOR DOME CAMERA
8
It is one of the most important parts of
the camera. Be careful not to be stained
by fingerprint.
User’s Manual
• If the camera is exposed to spotlight or object reflecting strong light, smear or
blooming may occur.
• Please check that the power satisfies the normal specification before connecting
the camera.
COLOR DOME CAMERA
9
User’s Manual
Name and Function of Each Section
Composition
1. SVD-4120A/AW
2. Instruction Manual
3. Quick Install Guide
4. Wrench
5. Ø5 Tapping Screws 4EA
6. Template
7. Video Output Cable for installer
COLOR DOME CAMERA
10 User’s Manual
COLOR DOME CAMERA
11 User’s Manual
Connection
Name and Function of Each Section
Pan Base
control panning angle of camera
Connecting to Monitor
Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.
Tilt Base Holding Serews
fix tilted position.
Pan Base Holding Screws (Color : Silver)
fix panned position
Zoom Handle
adjust zoom between WIDE and TELE
Focus Handle
after adjusting zoom, adjust focus
SET Button
confirm the status of the selected feature
CCTV Camera
Monitor
RIGHT Button
move cursor to the right, change the status of the selected feature
• As the connecting method varies with the instruments, refer to the manual
supplied with the instrument.
DOWN Button
move cursor to the down, select the desired feature item
• If necessary, you can connect the monitor to the REMOTE jack on the back of
your camera.
UP Button
move cursor to the up, select the desired feature item
• Only connect the cable when the power is turned off.
LEFT Button
move cursor to the left, change the status of the selected feature
• Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate
device.
Intermediate
Video Output Terminal
Video Output Terminal to Monitor
Video Output Jack
Power Input Jack
Shield Case
CCTV Camera
Dome Cover
COLOR DOME CAMERA
12 User’s Manual
COLOR DOME CAMERA
13 User’s Manual
End monitor
Connection
Operating Your Camera
Connecting to Power
Configuration of The Menu
SETUP MENU
• Use AC 24V / 300mA or DC 12V / 500mA power source.
CAMERA ID (see page 17)
• OFF • ON
BACKLIGHT (see page 20)
• WDR • BLC • OFF
WHITE BAL. (see page 21)
• W-ATW • S-ATW • AWC
• MANUAL
MOTION DET. (see page 22)
• OFF • MD1 • MD2
IRIS LEVEL CONTROL (see page 25)
• LEVEL
For DC Power Type
SHUTTER (see page 26)
• OFF • 1/100 (1/120) • MANUAL
• For DC power as the voltage drop according to the length of the cable in the
above table, a camera may malfunction if there is an excessively long cable run.
SENSE UP (see page 27)
• Auto • OFF
Resistance of copper wire [at 20C˚ (68˚F)]
2
2
2
2
#24(0.22mm )
#22(0.33mm )
#20(0.52mm )
#18(0.83mm )
Resistance ( Ω / m)
0.078
0.050
0.030
0.018
Voltage Drop (V/m)
0.028
0.018
0.011
0.006
Copper wire size (AWG)
GAIN (see page 28)
• OFF • AGC-L • AGC-H
* Voltage for camera operation: 12V DC ±10%
* Voltage drops in the above table are variable according to types of cable manufacturer.
SSNR (see page 28)
• OFF • LOW • MIDDLE • HIGH
Notes
• Be sure to connect power only after all the installation is complete.
• Note that AC or DC adaptor is not supplied with camera.
• Use the UL listed, class 2 power transformer of AC 24V adaptor.
• Ground should be connected to the GND terminal.
COLOR DOME CAMERA
14 User’s Manual
SPECIAL (see page 30)
• COLOR • SYNC • PRIVACY • RESET
• END
• EXIT
EXIT
COLOR DOME CAMERA
15 User’s Manual
Operating Your Camera
SETUP
Setting Up The Menu
Select the function using
the UP or DOWN button.
Use the five SETUP MENU buttons on back of the camera.
LEFT button
UP button
DOWN button
RIGHT button
SET button
CAMERA ID
BACKLIGHT
WHITE BAL.
MOTION DET.
IRIS
SHUTTER
SENSE UP
GAIN
SSNR
SPECIAL
EXIT
OFF
WDR
W-ATW
OFF
LEVEL
OFF
OFF
AGC-L
MIDDLE
Change the status using
the LEFT or RIGHT button.
3. Change the status of the selected feature using the LEFT or RIGHT button.
4. When completed, move the arrow indicator to 'EXIT' and press the SET button.
Notes
1. Press the SET button to access the SETUP mode.
• SETUP menu is displayed on the monitor screen.
• For the mode with you can access submenu.
• You can access submenu using SET button.
SETUP
CAMERA ID
BACKLIGHT
WHITE BAL.
MOTION DET.
IRIS
SHUTTER
SENSE UP
GAIN
SSNR
SPECIAL
EXIT
OFF
WDR
W-ATW
OFF
LEVEL
OFF
OFF
AGC-L
MIDDLE
2. Select the desired feature using the UP or DOWN button.
• Each time you press the UP or DOWN button, the arrow indicator moves up
or down.
• Move the arrow indicator to the desired feature item.
COLOR DOME CAMERA
16 User’s Manual
CAMERA ID
If you enter a CAMERA ID, the name will be displayed in the screen monitor.
1. Press the SET button to display the SETUP menu and move the arrow
indicator to 'CAMERA ID' using the UP or DOWN button.
2. Set 'CAMERA ID' to 'ON' using the LEFT or RIGHT button.
Notes
SETUP
• If the CAMERA ID feature is set to 'OFF', the name
will not displayed in the monitor.
COLOR DOME CAMERA
17 User’s Manual
CAMERA ID
BACKLIGHT
WHITE BAL.
MOTION DET.
IRIS
SHUTTER
SENSE UP
GAIN
SSNR
SPECIAL
EXIT
OFF
WDR
W-ATW
OFF
LEVEL
OFF
OFF
AGC-L
MIDDLE
Operating Your Camera
3. Press SET button.
5. Select the position at which the CAMERA ID will be located on the screen.
Move the cursor to 'POS' and press SET button.
CANERA ID
CAMERA ID
POS
CLR RESET END
POS
4. You can enter up to 16 characters.
Move the cursor to character-enter location by using the LEFT or RIGHT button.
CLR RESET END
The CAMERA ID is displayed on the bottom-left of the monitor screen.
(Default position)
Select the desired character by using UP or DOWN button.
•The factory defualt characters are A, B, ···, a, b, ···, ., -, ··· 0, 1···, 8, 9
CAMERA ID
POS
CLR RESET END
Press the SET button to confirm the blinking character. The first character is
saved and the cursor in the bottom of the screen moves to the next position.
Repeats steps
,
and
until you create the full name you want.
FRONT DOOR
Select the position by using the 4-directional buttons, then press the SET
button to confirm the position.
FRONT DOOR
Notes
• If you make a mistake while entering name
Move the cursor to ‘CLR’, press ‘SET’ button.
After erasing the character from right to left, correct the character again.
6. When completed, move the cursor to 'END' and press SET button.
COLOR DOME CAMERA
18 User’s Manual
COLOR DOME CAMERA
19 User’s Manual
Operating Your Camera
4. When completed, press the SET button.
BACKLIGHT
SV-II DSP chip built-in provides intelligent light level control to overcome the
severe Backlight conditions.
1. Press the SET button to display the SETUP menu and move the arrow
indicator to ‘BACKLIGHT’ using the UP or DOWN button.
SETUP
CAMERA ID
BACKLIGHT
WHITE BAL.
Notes
• If you select WDR mode, the following phenomenon may appear by lighting
condition. In these cases do not select WDR mode.
Unnatural color change or unnatural phenomenon on the screen
Noise of bright part on the screen
• According to the area of bright part on the screen there may be the difference of
WDR performance so be sure to adjust the degrees of the visual angle when
installing your camera.
OFF
WDR
W-ATW
• If you increase WDR level, unnatural phenomenon may appear.
2. SET ‘BACKLIGHT’ to the desired mode using the LEFT or RIGHT button.
WDR: In case that bright and dark parts exist on the screen at the same time,
your camera allows you to see both parts clearly
BLC: When the image is in front of strong background lighting, your camera
allows you to get the clear image
OFF: Deactivation
WHITE BALANCE CONTROL
Your camera provides 4 ‘WHITE BAL.’ control modes. You can select the most
suitable one. You can adjust the white balance.
1. Press the SET button to display the SETUP menu and move the arrow indicator
to 'WHITE BALANCE' using the UP or DOWN button.
2. Set ‘WHITE BAL.’ to the desired mode using LEFT or RIGHT button.
SETUP
WDR
BLC
OFF
3. Press the ‘SET’ button.
• When ‘WDR’ is chosen, you can adjust the level.
CAMERA ID
BACKLIGHT
WHITE BAL.
MOTION DET.
IRIS
OFF
WDR
W-ATW
OFF
LEVEL
WDR SET
LEVEL
0
PRESS SET TO RETURN
You can select the level from -4 to 4. WDR sensitivity is increased or decreased.
COLOR DOME CAMERA
20 User’s Manual
The six WHITE BALANCE control modes are as follows :
W-ATW(Wide Auto Tracking White balance):
When color temperature is 2400~12000K, select this mode. (EX. a fluorescent
lamp, outdoor)
COLOR DOME CAMERA
21 User’s Manual
Operating Your Camera
S-ATW(Special Auto Tracking White balance): When color temperature is
1800~6000K, specially in sodium lamp, select this mode. (EX. sodium lamp,
inside the tunnel)
AWC(Auto White balance Control): The white balance is automatically
adjusted in a specific environment. In order to obtain the best result, press the SET
button while the camera focuses on white paper. If the environment including the
light source is changed, you have to adjust the white balance again.
MANUAL : To fine adjust, select the Manual mode. You can increase or
decrease the red or blue factor while monitoring the difference on the screen.
Set to 'MANUAL' mode and press the SET button. Increase or decrease the
value for RED(R-Gain) and BLUE(B-Gain), watching the color of the picture, and
press the SET button when you obtain the best color.
2. Set ‘MOTION DET.’ to the desired mode using LEFT or RIGHT button.
SETUP
CAMERA ID
BACKLIGHT
WHITE BAL.
MOTION DET.
IRIS
SHUTTER
OFF
WDR
W-ATW
OFF
LEVEL
OFF
MD1: Your camera detects the object’s motion by outline or difference of a
color tone, so this mode is very useful for the daytime or observing
small moving object.
Press SET button.
Notes
• Proper White Balance may not be obtained under the following conditions, in these
cases select the AWC mode.
When the scene contains mostly high color temperature object, such as a blue
sky or sunset.
When the scene is dim.
If your camera faces fluorescent lamp directly or is installed in the place of the
changing illumination.
Move the arrow indicator to ‘AREA SET’ using UP and DOWN button, and
then press the SET button.
Set the areas you want to observe.
· You can adjust the top, bottom, left and right base lines by 13 steps from top to
bottom, 18 steps from left to right with an increment of 1.
MOTION DETECTION
Whenever your camera detects motion of object displaying ‘MOTION DETECTED’
with the number counted up on the screen.
1. Press the SET button to display the SETUP menu and move the arrow
indicator to 'MOTION DET.' using the UP or DOWN button.
COLOR DOME CAMERA
22 User’s Manual
COLOR DOME CAMERA
23 User’s Manual
Operating Your Camera
· Move the arrow indicator to 'TOP' using the UP or DOWN button and increase or
decrease the value using the LEFT or RIGHT button. Repeat the procedure for
bottom, left and right.
18
6
13
Maximum
5
Minimum
· When completed, press SET button.
MD2: Your camera detects object’s motion by the variation of brightness, so
this mode is very useful for night or observing large moving object.
Also MD2 enables you to set seperated areas.
Press SET button.
Move the arrow indicator to ‘AREA SET’ like MD1.
Set the areas you want to observe of the 48 areas.
Tips on Using the Motion Detection Feature
• As you increase or decrease MD LEVEL, the areas’ sensitivity is increased or
decreased for object.
• After selecting zone and sensitivity, perform a test operation to make sure it
works properly.
• If the lighting flickers, the motion detection feature might not work properly.
• The object should occupy 10% or more of its zone. The bigger the object, the
higher sensitivity.
• If the brightness of an object changes rapidly by sudden lighting change, the
camera may detect it as a motion.
• Your camera can count up to 999. If you reset your camera with selecting
‘RESET’ in SPECIAL menu or turn it off and on, your camera’ll count up from 0.
• When this feature is activated, another algorithm may take more time to be operated.
• This system does not guarantee prevention of fires or thefts. The manufacturer
is not responsible for any accident or damage.
IRIS LEVEL CONTROL
· Move the cursor to the area you want to observe, and then press the SET button.
· After setting, move the cursor to edge in any direction and then press the button
just one more, let ‘END’ blink.
· Press the SET button.
Notes
• If you set some areas of 48 areas, your camera detects the object’s motion within
the areas you set.
COLOR DOME CAMERA
24 User’s Manual
You can control the brightness of the screen.
1. Press the SET button to display the setup menu and move the arrow indicator
to 'IRIS' using the UP or DOWN button and press SET button.
2. Set ‘LEVEL’ to the desired brightness using LEFT or RIGHT button.
SETUP
CAMERA ID
BACKLIGHT
WHITE BAL.
MOTION DET.
IRIS
SHUTTER
OFF
WDR
W-ATW
OFF
LEVEL
OFF
3. When completed move the arrow indicator to ‘END’ and press the SET button.
COLOR DOME CAMERA
25 User’s Manual
Operating Your Camera
4. When completed, press the SET button.
SHUTTER SPEED CONTROL
You can control brightness of the screen by the shutter speed.
1. Press the SET button to display the setup menu and move the arrow indicator
to ‘SHUTTER’ using the UP or DOWN button.
2. Set ‘SHUTTER’ to the desired mode using the LEFT or RIGHT button.
OFF: Deactivation
1/100(1/120: PAL Models): Flickerless mode (When WDR is on, the image
can flicker a little)
MANUAL: When setting shutter speed manually
Notes
• For effective 1/100(1/120) mode set WDR mode in BACKLIGHT menu to OFF.
1/100(1/120) mode is not effective with WDR mode.
• If you choose MANUAL mode, you can’t use WDR mode in ‘BACKLIGHT’ menu.
• If you select MANUAL mode, SENSE UP is not operated.
SENSE UP
SETUP
CAMERA ID
BACKLIGHT
WHITE BAL.
MOTION DET.
IRIS
SHUTTER
SENSE UP
GAIN
You can always get the clear image with this function under night or lowlighting level.
1. Press the SET button to display the setup menu and move the arrow
indicator to 'SENSE UP' using the UP or DOWN button.
2. Set ‘SENSE UP’ to the desired mode using the LEFT or RIGHT button.
AUTO: When your camera is under night or low-lighting level, select this
mode.
OFF: Deactivation
OFF
WDR
W-ATW
OFF
LEVEL
OFF
OFF
AGC-L
3. If you choose ‘MANUAL’, select the optimal shutter speed.
• You can select speed from ‘1/60’ to ‘1/200,000’sec (NTSC Models), ‘1/50’ to
‘1/200,000’sec (PAL Models).
• When the shutter speed is increased or decreased using the LEFT or RIGHT
button, you can find the difference by monitoring the brightness of the
screen.
MANUAL SET
MANUAL SET
VALUE : 1/60
VALUE : 1/50
PRESS SET TO RETURN
PRESS SET TO RETURN
NTSC Models
PAL Models
COLOR DOME CAMERA
26 User’s Manual
SETUP
CAMERA ID
BACKLIGHT
WHITE BAL.
MOTION DET.
IRIS
SHUTTER
SENSE UP
GAIN
SSNR
SPECIAL
EXIT
COLOR DOME CAMERA
OFF
WDR
W-ATW
OFF
LEVEL
OFF
OFF
AGC-L
MIDDLE
27 User’s Manual
Operating Your Camera
GAIN
To get brighter picture.
1. Press the SET button to display the setup menu and move the arrow indicator
to ‘GAIN’ using the UP or DOWN button.
2. Set ‘gain’ to desired mode using the LEFT or RIGHT mode.
AGC-H: Gain is increased or decreased from 0 to 30dB automatically as
following the illumination.
AGC-L: Gain is increased or decreased from 0 to 27dB automatically as
following the illumination.
OFF: Deactivation
MIDDLE: middle reduction of the noise
HIGH: high reduction of the noise
OFF: Deactivation
SETUP
CAMERA ID
BACKLIGHT
WHITE BAL.
MOTION DET.
IRIS
SHUTTER
SENSE UP
GAIN
SSNR
SPECIAL
EXIT
SETUP
CAMERA ID
BACKLIGHT
WHITE BAL.
MOTION DET.
IRIS
SHUTTER
SENSE UP
GAIN
SSNR
SPECIAL
EXIT
OFF
WDR
W-ATW
OFF
LEVEL
OFF
OFF
AGC-L
MIDDLE
OFF
WDR
W-ATW
OFF
LEVEL
OFF
OFF
AGC-L
MIDDLE
Notes
• If you change the ‘GAIN’ menu from AGC-L to AGC-H, sensitivity is increased as well
as noise on the screen.
• Afterimage may appear with SSNR.
SSNR(Samsung Super Noise Reduction)
To reduce the noise on the screen.
1. Press the SET button to display the setup menu and move the arrow indicator
to ‘SSNR’ using the UP or DOWN button.
2. Set ‘SSNR’ to desired mode using the LEFT or RIGHT mode.
LOW: low reduction of the noise
COLOR DOME CAMERA
28 User’s Manual
COLOR DOME CAMERA
29 User’s Manual
Operating Your Camera
Notes
SPECIAL
• When the power frequency is 50Hz, you can not use line-lock mode(NTSC Models).
• When the power frequency is 60Hz, you can not use the line-lock mode(PAL Models).
• ‘Sync.’ mode is fixed to ‘INT’ in DC 12V input power.
PRIVACY: To mask area which you want to mask
- OFF: Deactivation
- ON: Privacy mode activated
1.Press the SET button to display the setup menu and move the arrow indicator to
‘SPECIAL’ using the UP or DOWN button.
2. Press the SET button.
COLOR : choose color or B/W mode
- ON : color mode
- OFF : B/W mode
- AUTO1 : generally color mode, B/W mode in low luminance.
- AUTO2 : AUTO2 is identical with AUTO1 under SENSE UP : AUTO condition.
SYNC : Two SYNCHRONIZATION modes are available INTERNAL and
EXTERNAL LINE-LOCK. In LINE-LOCK mode, it synchronizes the
video signal between cameras without a synchronous generator.
The line-lock synchronization is only used in the areas of 60Hz
(NTSC Models) / 50Hz (PAL Models).
- INT : Internal synchronization
- OFF : External line-lock synchronization
· If you choose ‘L/L’, you can adjust the desired phase. Press the SET button.
-You can adjust the desired phase from 0 to 270.
· Press the SET button.
· Move the arrow indicator to area you want to mask.
· Set ‘ON’ using LEFT or RIGHT button.
· Press the SET button and then set the area’s bounds with the method like
MD1 Set. (see page 23)
· When completed, press the SET button.
RESET: To reset your camera to factory default condition
END: To move Top-menu
EXIT: To finish setting menu
LINE LOCK
PHASE : 225
PRESS SET TO RETURN
COLOR DOME CAMERA
30 User’s Manual
COLOR DOME CAMERA
31 User’s Manual
Troubleshooting
If you have trouble operating your camera, refer to the following table. If the
guidelines do not enable you to solve the problem, contact an authorized
technician.
Problem
Nothing appears on
the screen.
Problem
Solution
The color of the picture
is not matched.
• Check that you have properly set the ‘WHITE BAL.’
menu. (refer to page 21)
The image on the screen
flickers.
• Is the camera facing to direct sunlight or fluoresent
lighting? Change the camera position.
L/L mode isn’t able to
be selected.
• Have you connected your camera to DC power
source? Connect it to AC power source.
Solution
• Check that the power cord and line connection
between the camera and monitor are fixed properly.
• Check that you have properly connected VIDEO
cable to the camera VIDEO output jack.
The image on the
screen is dim.
• Is lens stained with dirt? Clean your lens with soft,
clean cloth.
• Set the monitor to proper condition.
• If the camera is exposed to too strong light, change
the camera position.
• Adjust the lens’ focus properly.
The image on the
screen is dark.
• Adjust the contrast feature of the monitor.
• If you have an intermediate device, set the 75Ω / Hi-z
properly. (refer to page 13)
The camera is not
working properly, and
the surface of the
camera is hot.
• Check that you have properly connected the camera
to an appropriate power source.
MOTION DETECTION
function is not active.
• Have you set ‘MOTION DET.’ menu to OFF?
• Have you set ‘MD LEVEL’ to too low?
• Have you set ‘MD AREA’ properly?
COLOR DOME CAMERA
32 User’s Manual
COLOR DOME CAMERA
33 User’s Manual
Dimension
Specifications
Ø 148mm
Item
SVD-4120AN
SVD-4120AP
Power Source
Power Consumption
280mA(DC) / 3.8W(AC)
Image Sensor
1/3”, Vertical double density interline CCD
Total Pixels
811(H)x508(V), 1/3”CCD
759(H)x596(V), 1/3”CCD
811(H)x508(V), 1/3”CCD
759(H)x596(V), 1/3”CCD
Effective Pixels
768(H)x494(V), 1/3”CCD
752(H)x582(V), 1/3”CCD
768(H)x494(V), 1/3”CCD
752(H)x582(V), 1/3”CCD
LENS TYPE
2.5X Vari-Focal,f=3.8~9.5
Maximum Aperature Ratio
126mm
Angle of View
Scanning System
Video Output
1:1.3~2.0
1:1.3~1.9
H: 108.2˚~47.6˚, V: 80.4˚~35.6˚, D:136.6˚~59.4˚
2:1 Interlaced 525
2:1 Interlaced 625
2:1 Interlaced 525
2:1 Interlaced 625
Lines/60Fields/30Frames
Lines/50Fields/25Frames
Lines/60Fields/30Frames
Lines/50Fields/25Frames
Internal / Line Lock selectable
1.0V[p-p]NTSC composite, 1.0V[p-p]PAL composite, 1.0V[p-p]NTSC composite, 1.0V[p-p]PAL composite,
75W/BNC Connector
75W/BNC Connector
Wide Dynamic Range
AGC-L, AGC-H, OFF selectable
1/60~1/200,000sec
1/50~1/200,000sec
SENSE UP
46mm
85mm
DC Drive
WHITE BALANCE
W-ATW / S-ATW / AWC / MANUAL
Min. Illumination
0.003Lux(Sense Up) / 0.3Lux(F1.3)
S/N(Y signal)
50dB (Weight ON)
Motion Detection
MD1 / MD2 / OFF
O.S.D
Built-in
SSNR
LOW / MIDDLE / HIGH /OFF
PRIVACY Function
ON / OFF(4 Programmable Zone)
Operating Temperature
-10˚C ~ +50˚C (14˚F ~ 122˚F)
Operating Humidity
30% ~ 90% RH
Dimension(mm)
f150(W) x 130(H)
1.4kg
Weight(W/O Lens & Power Cord)
Panning : 340˚ , Tilt : 70˚
Angle
COLOR DOME CAMERA
34 User’s Manual
1/60~1/200,000sec
Built-in(selectable limit~X128)
IRIS MODE
85mm
75W/BNC Connector
ON / OFF / AUTO
Gain Control
83.5mm
75W/BNC Connector
500TV Lines
Resolution
Electric Shutter Speed
2.4X Vari-Focal,f=2.5~6.0
H: 74.2˚~30.0˚, V: 54.0˚~22.4˚, D: 96.8˚~37.4˚
Synchronization
85mm
SVD-4120AWN SVD-4120AWP
DC 12V / AC 24V compatible
* Design and specifications are subject to change without notice
COLOR DOME CAMERA
35 User’s Manual
1/50~1/200,000sec
DECLARATION OF CONFORMITY
Application of Council Directive(s)
89 / 336 / EEC
Manufacturer's Name
SAMSUNG TECHWIN CO., LTD
Manufacturer's Address
SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-120
European Representative Name
European Representative Address
Equipment Type/Environment
CCTV Camera
Model Name
SVD-4120A/AW
Beginning Serial NO.
S4100002
Year of Manufacture
2004. 1. 2
Conformance to
EN 50081-1 : 1992
EMC-Directive 89/336 EEC and 92/31/EEC
EN 50130-4 : 1996
We, the undersigned, here by declare that the equipment specified above conforms
to the above Directive(s).
SAMSUNG TECHWIN CO., LTD
Legal Representative in Europe
Full Name
YOUNG TAEK SON
Full Name
Position
QUALITY CONTROL MANAGER
Position
Place
CHANGWON, KOREA
Place
Date
2004. 1. 2
Date
Manufacturer
Signature
Signature
MEMO
MEMO
MEMO