Model No. PFTL99602
Serial No.
USER'S MANUAL
Find the serial number in the location
shown below. Write the serial number
in the space above for reference.
Serial Number Decal
QUESTIONS?
If you have questions, or if there
are missing parts, we will guarantee complete satisfaction
through direct assistance from
our factory.
TO AVOID UNNECESSARY DELAYS, PLEASE CALL DIRECT TO
OUR TOLL-FREE CUSTOMER
HOT LINE. The trained technicians on our Customer Hot Line
will provide immediate assistance, free of charge to you.
CUSTOMER HOT LINE:
1-888-533-1333
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Patent Pending
Visit our website at
www.proform.com
new products, prizes,
fitness tips, and much more!
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING is attached in the center of this manual.
PROFORM is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
12. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed or stop unexpectedly, which may result
in a fall and serious injury.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
2. Use the treadmill only as described in this
manual.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
13. Keep the power cord and the surge suppressor away from heated surfaces.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 5 if the treadmill is not working properly.)
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
15. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
7. The treadmill should not be used by persons
weighing more than 250 pounds.
17. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothing when
using the treadmill. Do not wear loose clothing that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
18. Using the included hand weights and not holding the handrails may compromise your ability
to maintain your balance. Exercises using
hand weights should be attempted only by experienced users.
19. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord and move the on/off switch to
the off position when the treadmill is not in
use. (See the drawing on page 5 for the location of the on/off switch.)
10. When connecting the power cord (see page 8),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
20. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 21.) You
must be able to safely lift 45 pounds (20 kg) in
order to raise, lower, or move the treadmill.
11. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 8. To purchase a surge suppressor, see
your local PROFORM dealer or call 1-888-5331333 and order part number 146148.
3
21. Do not change the incline of the treadmill by
placing objects under the treadmill.
25. Always remove iFIT.com CD’s and videos
from your CD player or VCR when you are not
using them.
26. Inspect and tighten all parts of the treadmill
regularly.
22. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
23. When using iFIT.com CD’s and videos, an
electronic “chirping” sound will alert you
when the speed and/or incline of the treadmill
is about to change. Always listen for the
“chirp” and be prepared for speed and/or incline changes. In some instances, the speed
and/or incline may change before the personal trainer describes the change.
27. Never insert or drop any object into any
opening.
28.
DANGER: Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the maintenance and adjustment procedures described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
24. When using iFIT.com CD’s and videos, you
can manually override the speed and incline
settings at any time by pressing the speed
and incline buttons. However, when the next
“chirp” is heard, the speed and/or incline will
change to the next settings of the CD or video
program.
29. This treadmill is intended for in-home use
only. Do not use this treadmill in any commercial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown below have been placed on your treadmill. If the decal is missing, or if it is not legible,
please call our Customer Service Department, toll-free, to order a free replacement decal (see ORDERING
REPLACEMENT PARTS on the back cover of this manual). Apply the decal in the location shown.
Note: This decal is shown at 38% of actual size.
4
BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM®
995 SEL treadmill. The 995 SEL treadmill combines
advanced technology with innovative design to help
you get the most from your exercise program in the
convenience of your home. And when you’re not exercising, the unique 995 SEL can be folded up, requiring
less than half the floor space of other treadmills.
at 1-888-533-1333, Monday through Friday, 6 a.m.
until 6 p.m. Mountain Time (excluding holidays). To
help us assist you, please note the product model
number and serial number before calling. The model
number of the treadmill is PFTL99602. The serial number can be found on a decal attached to the treadmill
(see the front cover of this manual for the location).
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
please call our Customer Service Department toll-free
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Book Holder
Hand Weights
Water Bottle
Holder (Bottle
not included)
Console
Pulse Sensor
Key/Clip
Handrail
Lock Knob
LEFT SIDE
RIGHT SIDE
Walking Belt
On/Off Switch
Circuit Breaker
Foot Rail
Power Cord
Adjustable Cushion Deck
Rear Roller
Adjustment Bolts
5
ASSEMBLY
Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Assembly requires your own phillips screwdriver
and rubber mallet
.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
1. With the help of a second person, carefully raise the
Uprights (64) to the position as shown.
1
64
Insert one of the Extension Legs (102) into the treadmill
as shown. Make sure that the Extension Leg is turned
so the Base Pad (99) is on the bottom. If necessary, tip
the Uprights (64) forward as you insert the Extension
Leg.
Insert the other Extension Leg (not shown) in the same
way.
102
99
2. With the help of a second person, carefully lower the
treadmill frame and then tip the Uprights (69) down as
shown. Make sure that the Extension Legs (102) remain
in the Uprights.
2
99
Attach each Extension Leg (102) with two of the six 3/4”
Screws (100) as shown.
Frame
With the help of a second person, carefully tip the
Uprights (69) back to the vertical position.
69
Note: One replacement Base Pad (99) may be included.
Use the extra Base Pad if one becomes worn or needs to
be replaced.
3. Insert a Handrail Extension (66) into the post on the right
Upright (69) as shown; make sure that the indicated holes
are on top. Tap the Handrail Extension with a rubber mallet
to fully insert it. Attach the Handrail Extension with two 1/2”
Screws (67) as shown.
Identify the Right Foam Grip (75), which has a large cutout
in the left side for the Pulse Bar (76). Slide the Right Foam
Grip as far as possible onto the post on the right Upright
(69). (Note: It may be helpful to apply soapy water to the
Handrail Extension [66].) Make sure that the tab on the
Foam Grip is inserted into the Console Base (81).
6
100
69
102
100
102
99
3
76
Tab
Cutout
81
67
Holes
69
75
66
Post
4. Make sure that the front edge of the Right Foam Grip (75)
is under the Console Base (81) as shown. Tighten a 3/4”
Screw (100) into the side of the Right Foam Grip as
shown. Note: It may be necessary to pull the Foam Grip
out slightly (see arrow A) to align the Screw with the hole
in the post.
4
81
A
100
Attach the other Handrail Extension (not shown) and the
Left Foam Grip (not shown) as described in step 3 and
this step.
5. Press the Lock Knob Sleeve (70) into the left Upright (69).
75
5
Make sure that the two Lock Pin Collars (72) and the
Spring (71) are on the Lock Pin (74). Insert the Lock Pin
into the Lock Knob Sleeve (70) and the left Upright (69).
Tighten the Lock Knob (68) onto the Lock Pin.
69
70
68
72
74
71
6. Look at the Endcap (58). If the left or right foot on the Endcap does not touch the floor, the included thick base pads
should be attached to the treadmill as described below.
Refer to assembly step 2. Lower the treadmill frame and
the Uprights (69) as shown. If the left foot of the Endcap
(58) was off the ground, remove the two Base Pads (99)
from the right Upright (69). Attach the included thick
base pads to the right Upright. If the right side of the
Endcap was off the ground, attach the thick base pads to
the left Upright.
If either side of the Endcap (58) lifts off the floor when the
treadmill is used, attach the thick base pads as described.
6
Foot
58
Foot
7. Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a
secure place. The allen wrench is used to adjust the walking belt (see page 21). To protect the floor or carpet
from damage, place a mat under the treadmill.
7
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETM WALKING BELT
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking platform. Such substances will deteriorate the walking
belt and cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER: Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local PROFORM dealer or call 1-888-533-1333
and order part number 146148.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated
for 120 volts AC and 15 amps. There must be a
monitoring light on the surge suppressor to indicate whether it is functioning properly. Failure to
use a properly functioning surge suppressor could
result in damage to the control system of the
treadmill. If the control system is damaged, the
walking belt may change speed or stop unexpectedly, which may result in a fall and serious injury.
Surge Suppressor
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having
8
CONSOLE DIAGRAM
Manual/Program Indicators
Program Display
Display
If there is a thin sheet of clear plastic
on the face of the console, remove it.
Display
Program Indicators
Clip
Key
Nine certified personal trainer programs are also
offered. Each program automatically controls the
speed and incline of the treadmill to give you an effective jogging or running workout. Two heart rate programs are also featured. Each program controls the
speed and incline of the treadmill to keep your heart
rate near a target level during your workouts. Note:
The heart rate programs require the use of the optional
chest pulse sensor (see page 20).
CAUTION:
Before operating the
console, read the following precautions.
• Do not stand on the walking belt when turning on the power.
• Always wear the clip (see the drawing
above) while operating the treadmill.
• Adjust the speed in small increments to
avoid sudden jumps in speed.
The console also features new iFIT.com interactive
technology. Having iFIT.com technology is like having a
personal trainer in your home. Using the included audio
cable, you can connect the treadmill to your home
stereo, portable stereo, computer, or VCR and play
special iFIT.com CD and video programs (iFIT.com
CDs and videocassettes are available separately).
iFIT.com CD and video programs automatically control
the speed and incline of the treadmill as a personal
trainer coaches you through every step of your workout.
High-energy music provides added motivation. To purchase iFIT.com CDs or videocassettes, call tollfree 1-888-533-1333.
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and place only a sealed water
bottle in the water bottle holder.
FEATURES OF THE CONSOLE
The advanced console offers an impressive array of
features to help you get the most from your exercise.
When the manual mode of the console is selected, the
speed and incline of the treadmill can be changed with
a touch of a button. As you exercise, the console will
display continuous exercise feedback. You can even
measure your heart rate using the pulse sensor or the
optional chest pulse sensor (see page 20).
With the treadmill connected to your computer, you
can also go to our Web site at www.iFIT.com and access programs directly from the internet. Additional options are soon to be available. See www.iFIT.com for
more information.
9
HOW TO TURN ON THE POWER
1
Plug in the power cord (see page 8).
2
Locate the on/off
switch on the treadmill
near the power cord.
Move the on/off
switch to the on position.
3
the Speed + and – buttons. Each time a button
is pressed, the speed
setting will change by
0.1 mph; if a button is
held down, the speed
setting will change in increments of 0.5 mph. To
change the speed setting quickly, press the Quick
Speed Control buttons.
On
Position
To stop the walking belt, press the Stop button.
The Time/Segment Time display will begin to
flash. To restart the walking belt, press the Start
button or the Speed + button.
Stand on the foot rails
of the treadmill. Find
the clip attached to the
key and slide the clip
onto the waistband of
your clothes. Next, insert the key into the console.
After a moment, the displays and various indicators will light. Test the clip by carefully taking a
few steps backward until the key is pulled
from the console. If the key is not pulled from
the console, adjust the position of the clip as
needed.
Note: During the first few minutes that the treadmill
is used, inspect the alignment of the walking belt,
and align it if necessary (see page 23).
4
To change the incline of
the treadmill, press the
Incline buttons. Each time
a button is pressed, the
incline will change by
0.5%. Note: After the buttons are pressed, it may take a moment for the
treadmill to reach the selected incline setting.
To use the manual mode of the console, follow the
steps beginning on page 10. To use a personal trainer
program, see page 12. To use a heart rate program,
see page 13. To use an iFIT.com CD or video program, see page 17. To use an iFIT.com program directly from our Web site, see page 19.
5
Insert the key fully into the console.
See HOW TO TURN ON THE POWER above.
2
3
Follow your progress with the LED track and
the displays.
The LED Track—
When the manual
mode or the
iFIT.com mode is
selected, the program display will
show an LED track
representing 1/4 mile. As you exercise, the indicators around the track will light in succession until
the entire track is lit. The track will then darken
and the indicators will again begin to light in succession.
HOW TO USE THE MANUAL MODE
1
Change the incline of the treadmill as desired.
Select the manual
mode.
When the key is inserted, the manual
mode will be selected
and the Manual indicator will light. If a program has been
selected, press the Program button repeatedly to
select the manual mode.
Distance/Incline/Laps
display—This display
shows the distance that
you have walked, the incline level of the treadmill,
and the number of 1/4mile laps you have completed. The display will
change from one number to the next every few
seconds. The Incline indicator or the Laps indicator
will light when the incline level or the number of
laps is shown. Note: Each time the Incline buttons
are pressed, the display will show the current incline setting for several seconds.
Press the Start button or the Speed + button to
start the walking belt.
A moment after the button is pressed, the walking
belt will begin to move at 1 mph. Hold the handrails
and begin walking. As you exercise, change the
speed of the walking belt as desired by pressing
10
Time/Segment Time
display—When the manual mode or the iFIT.com
mode is selected, this
display will show the
elapsed time. When a
personal trainer program or a heart rate program is
selected, the display will show both the time remaining in the program and the time remaining in
the current segment of the program. The display
will alternate between one number and the other
every few seconds. The Segment Time indicator
will light when the segment time is shown.
6
Measure your heart rate, if desired.
Note: Before using the pulse sensor, make sure
that your hands are clean.
To measure your
heart rate, stand
on the foot rails
and place both
thumbs on the
pulse sensor as
shown. Do not
press too hard,
or the circulation in your
thumbs will be
restricted and
your heart rate will not be detected. After a few
seconds, one or two dashes will appear in the
Pulse display and then your heart rate will be
shown. Hold your thumbs on the sensor for another 15 seconds for the most accurate reading. If
the displayed heart rate appears to be too high or
too low, or if your heart rate is not displayed, lift
your thumbs off the sensor and allow the display to
reset. Then, place your thumbs on the sensor as
described above. Remember to stand still while
measuring your heart rate. Note: If the optional
chest pulse sensor is worn, your heart rate will be
displayed in the Pulse display.
Calories/Fat Calories/
Heart Rate display—
This display shows the
approximate numbers of
calories and fat calories
you have burned (see
FAT BURNING on page 25). This display will also
show your heart rate when you use the pulse sensor or the optional chest pulse sensor. Every few
seconds, the display will change from one number
to the next. The Fat Cals. indicator or the Heart
Rate indicator will light when the number of fat
calories or your heart rate is shown.
Speed/Min-mile
display—This display
shows the speed of the
walking belt and your
current pace (pace is
measured in minutes per
mile). Every few seconds, the display will change
from one number to the other. The Min/ Mile indicator will light when your pace is shown.
7
When you are finished, remove the key from
the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting when the treadmill is folded to the storage
position or the treadmill will be damaged. Next,
remove the key from the console and put it in a secure place. Note: If the displays and various indicators on the console remain lit after the key
is removed, the console is in the “demo”
mode. See page 20 and turn off the demo mode.
Note: The console can
display speed and distance in either miles or
kilometers. To find which
unit of measurement is
selected, hold down the
Stop button while inserting the key into the console. An E, for English miles, or an M, for metric
kilometers, will appear in the display. Press the
Speed + button to change the unit of measurement. When the desired unit of measurement is
selected, remove the key and then reinsert it.
Note: For simplicity, all instructions in this
manual refer to miles.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position and unplug the power cord from the front
of the treadmill.
To reset the displays, press the Stop button, remove the key, and then reinsert the key.
11
the flashing Current
Current Segment
Segment column of
the program display.
(The incline settings
are not shown in the
program display.)
The speed settings
for the next several
segments will be shown in the columns to the
right.
HOW TO USE PERSONAL TRAINER PROGRAMS
1
Insert the key fully into the console.
See HOW TO TURN ON THE POWER on page 10.
2
Select one of the personal trainer programs.
When the key is
inserted, the
manual mode will
be selected. To
select one of the
personal trainer
programs, press
the Program button repeatedly until one of the
nine personal trainer program indicators lights.
When a personal trainer program is selected, the
Distance/Incline/Laps display will flash the maximum incline setting for the program for six seconds, and the Speed/Min-mile display will flash
the maximum speed setting.
When only three seconds remain in the first segment of the program, both the Current Segment
column and the column to the right will flash and a
tone will sound. In addition, if the speed and/or incline of the treadmill is about to change, the
Speed/Min-mile display and/or the Distance/
Incline/Laps display will flash to alert you, and
three tones will sound. When the first segment is
completed, all speed settings will move one column to the left. The speed setting for the second
segment will then be shown in the flashing
Current Segment column and the treadmill will automatically adjust to the speed and incline settings
for the second segment.
The console features four jogging programs and
five running programs. The profiles on the console
show how the speed and incline of the treadmill
will change during the programs. The numbers
beside the profiles show the maximum speed and
incline settings for the programs.
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and no time remains in
the Time/Segment Time display. The walking belt
will then slow to a stop.
The program display will show a
simplified profile of
the program you
have selected. The
Time/Segment
Time display will
show how long the program will last.
3
Note: Each time a segment ends and the speed
settings move one column to the left, if all of the
indicators in the Current Segment column are lit,
the speed settings will move downward so that only
the highest indicators in the columns will appear in
the program display. When the speed settings
move to the left again and not all of the indicators
in the Current Segment column are lit, the speed
settings will move back up.
Press the Start button or the Speed + button to
start the program.
If the speed or incline setting for the current
segment is too high or too low, you can manually
override the setting by pressing the Speed or
Incline buttons on the console. Every few times
one of the Speed buttons is pressed, an additional
indicator will light or darken in the Current Segment
column. If any of the columns to the right of the
Current Segment column have the same number
of lit indicators as the Current Segment column,
an additional indicator may light or darken in those
columns as well. Note: If you manually adjust the
speed setting so that all of the indicators in the
Current Segment column are lit, the speed settings
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
Each program is divided into several time segments of different lengths. The Time/Segment
Time display shows both the time remaining in the
program and the time remaining in the current
segment. One speed setting and one incline setting are programmed for each segment. The
speed setting for the first segment will be shown in
12
in the program display will not move downward as
described above. When the current segment of
the program ends, the treadmill will automatically adjust to the speed and incline settings
for the next segment.
To stop the program temporarily, press the Stop
button. The Time/Segment Time display will begin
to flash. To restart the program, press the Start button or the Speed + button. The walking belt will
begin to move at 1 mph. When the current segment of the programs ends, the treadmill will automatically adjust to the speed and incline settings
for the next segment. To end the program at any
time, press the Stop button, remove the key, and
then reinsert the key.
4
HOW TO USE HEART RATE PROGRAMS
CAUTION:
If you have heart problems, or if you are over 60 years of age and
have been inactive, do not use the heart rate
programs. If you are taking medication regularly, consult your physician to find whether the
medication will affect your exercise heart rate.
Follow the steps below to use the heart rate programs.
Note: You must wear the optional chest pulse sensor (see page 20) to use the heart rate programs.
Follow your progress with the displays.
1
See the instructions included with the optional
chest pulse sensor.
See step 5 on page 10.
5
Measure your heart rate, if desired.
2
See step 6 on page 11.
6
Put on the chest pulse sensor.
Insert the key fully into the console.
See HOW TO TURN ON THE POWER on page
10.
When the program is completed, remove the
key from the console.
3
When the program has ended, make sure that
the incline of the treadmill is at the lowest setting. Next, remove the key from the console and
put it in a safe place. Note: If the displays and
various indicators on the console remain lit
after the key is removed, the console is in the
“demo” mode. See page 20 and turn off the
demo mode.
Select a heart rate program.
When the key is
inserted, the manual mode will be
selected. To select one of the
heart rate programs, press the
Program button repeatedly until one of the two
heart rate program indicators lights.
When you are finished using the treadmill, move
the on/off switch near the power cord to the off
position and unplug the power cord from the front
of the treadmill.
The two lower profiles on the left side of the console show how the target heart rate will change
during the programs. The numbers beside the
profiles show the minimum and maximum target
heart rate settings for the programs. Note: The
numbers are percentages of your estimated maximum heart rate. Your estimated maximum heart
rate is determined by subtracting your age from
220. For example, if you are 30 years old, your
estimated maximum heart rate is 190 beats per
minute (220 – 30 = 190). 50% of your estimated
maximum heart rate would be 95 beats per minute
(50% of 190 is 95).
13
ries of tones will sound, and the Distance/Incline/
Laps display and the Speed/Min-mile display will
flash. When the first segment is completed, all
heart rate settings will move one column to the
left. The heart rate setting for the second segment
will then be shown in the flashing Current
Segment column, and the speed and/or incline of
the treadmill will change, if needed, to bring your
heart rate closer to the heart rate setting for the
second segment.
The program display will show a
simplified profile of
the program you
have selected. The
Time/Segment
Time display will
show how long the program will last.
4
Enter your age.
The program will continue until the target heart
rate setting for the last segment is shown in the
Current Segment column and no time remains in
the program. The walking belt will then slow to a
stop.
When a heart rate program is selected, the
word AGE will begin to
flash in the Distance/
Incline/Laps display. You
must enter your age to
use a heart rate program. If you have already entered your age, go to step 5. If you have not entered your age, press the Incline (Age Set) buttons
until your age is shown. Your age will then be
saved in memory.
5
If the speed or incline setting for the current segment is too high or too low, you can adjust the setting with the Speed or Incline buttons. However, if
you decrease the speed, the incline will automatically increase; if you increase the speed, the incline will decrease. If you increase the incline, the
speed will decrease; if you decrease the incline,
the speed will increase. The treadmill will always
attempt to keep your heart rate near the target
heart rate setting for the current segment. Note:
When the incline reaches the lowest setting, the
speed cannot be increased further. When the incline reaches the highest setting, the speed cannot be decreased further.
Press the Start button or the Speed + button to
start the program.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
Each heart rate program is divided into one-minute
segments. The Time/Segment Time display will
show both the time remaining in the program and
the time remaining in the current segment of the
program. One target heart rate setting is programmed for each segment. (The same target
heart rate setting may be programmed for consecutive segments.) The
target heart rate
Current Segment
setting for the first
segment will be
shown in the flashing Current
Segment column of
the program display. The target
heart rate settings for the next several segments
will be shown in the columns to the right.
If your pulse is not detected during the program,
the letters PLS will flash in the Calories/Fat
Calories/Heart Rate display and the speed and incline of the treadmill may automatically decrease
until your pulse is detected. If this occurs, see the
instructions included with the chest pulse sensor.
To stop the program at any time, press the Stop
button. Heart rate programs should not be stopped
temporarily and then restarted. To use a heart rate
program again, reselect the program and start it at
the beginning.
6
Follow your progress with the displays.
See step 5 on page 10.
7
When only three seconds remain in the first segment of the program, both the Current Segment
column and the column to the right will flash, a se-
When the program is completed, remove the
key from the console.
See step 6 on page 13.
14
HOW TO CONNECT YOUR PORTABLE STEREO
HOW TO CONNECT THE TREADMILL TO YOUR
CD PLAYER, VCR, OR COMPUTER
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3.5mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
To use iFIT.com CD’s, the treadmill must be connected to your portable CD player, portable stereo,
home stereo, or computer with CD player. See pages
15 and 16 for connecting instructions. To use iFIT.com
videocassettes, the treadmill must be connected to
your VCR. See page 17 for connecting instructions. To
use iFIT.com programs directly from our internet
site, the treadmill must be connected to your home
computer. See page 16 for connecting instructions.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter. Plug
the adapter into an AUDIO OUT jack on your stereo.
A
HOW TO CONNECT YOUR PORTABLE CD PLAYER
AUDIO OUT
RIGHT
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
LEFT
Audio
Cable
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your CD player. Plug your headphones into the
PHONES jack.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your stereo.
A
PHONES LINE OUT
LINE OUT
Adapter
PHONES
B
Headphones
Audio
Cable
LINE OUT
Audio
Cable
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your CD player. Plug your
headphones into the other side of the Y-adapter.
C. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your stereo. Plug your
headphones into the other side of the Y-adapter.
B
PHONES
C
PHONES
Audio
Cable
3.5mm
Y-adapter
PHONES
Audio
Cable
Headphones
3.5mm
Y-adapter
Headphones
15
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
Note: If your computer has a 3.5mm LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the LINE OUT jack on your
stereo.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your computer.
A
A
CD
LINE OUT
VCR
Amp
LINE OUT
Audio
Cable
LINE OUT
Audio
Cable
Adapter
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the LINE OUT jack on your
stereo and plug the wire into the unused side of the
Y-adapter. Plug the Y-adapter into the LINE OUT
jack on your stereo.
B
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your computer. Plug your
headphones or speakers into the other side of the
Y-adapter.
B
PHONES
CD
Audio
Cable
VCR
Amp
3.5mm
Y-adapter
LINE OUT
Headphones/Speakers
Audio
Cable
RCA
Y-Adapter
Adapter
Wire removed from
LINE OUT jack
16
HOW TO CONNECT YOUR VCR
HOW TO USE IFIT.COM CD AND VIDEO
PROGRAMS
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 16.
To use iFIT.com CD’s or videocassettes, the treadmill
must be connected to your portable CD player, portable
stereo, home stereo, computer with CD player, or
VCR. See HOW TO CONNECT THE TREADMILL TO
YOUR CD PLAYER, VCR, OR COMPUTER on pages
15 and 16. Note: To purchase iFIT.com CD’s or
videocassettes, call toll-free 1-888-533-1333. .
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the AUDIO OUT jack on your
VCR.
Follow the steps below to use an iFIT.com CD or video
program.
A
1
ANT. IN
VIDEO AUDIO
IN
RF OUT
CH
3 4
Insert the key into the console.
OUT
See HOW TO TURN ON THE POWER on page 10.
AUDIO OUT
RIGHT
LEFT
Audio
Cable
2
Adapter
Select the iFIT.com mode.
When the key is
inserted, the
manual mode will
be selected. To
use iFIT.com
CDs or videocassettes, press the
Program button repeatedly until the iFIT.com indicator lights.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the AUDIO OUT jack on your
VCR and plug the wire into the unused side of the
Y-adapter. Plug the Y-adapter into the AUDIO OUT
jack on your VCR.
3
A
Insert the iFIT.com CD or videocassette.
If you are using an iFIT.com CD, insert the CD
into your CD player. If you are using an iFIT.com
videocassette, insert the videocassette into your
VCR.
4
B
ANT. IN
VIDEO AUDIO
IN
Press the PLAY button on your CD player or
VCR.
RF OUT
CH
3 4
OUT
A moment after the button is pressed, your personal trainer will begin guiding you through your
workout. Simply follow your personal trainer’s
instructions. Note: If the Time/Segment Time display is flashing, press the Start button or the
Speed + button on the console. The treadmill will
not respond to a CD or video program when the
Time/Segment Time display is flashing.
RCA Y-Adapter
Audio
Cable
Adapter
Wire removed from
AUDIO OUT jack
During the CD or video program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes. In
some instances, the speed and/or incline may
change before the personal trainer describes
the change.
17
• Adjust the volume of your CD player or VCR.
If the volume is too high or too low, the console may not detect the program signals.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the CD or video program.
• Make sure that the audio cable is properly
connected, that it is fully plugged in, and that
it is not wrapped around a power cord.
To stop the walking belt at any time, press the
Stop button on the console. The Time/Segment
Time display will begin to flash. To restart the program, press the Start button or the Speed + button. After a moment, the walking belt will begin to
move at 1.0 mph. When the next “chirp” is
heard, the speed and incline will change to the
next settings of the CD or video program. The
program can also be stopped by pressing the
Stop button on your CD player or VCR.
• If you are using your portable CD player and
the CD skips, set the CD player on the floor or
another flat surface instead of on the console.
5
Follow your progress with the LED track and
the displays.
See step 5 on page 10.
6
When the CD or video program is completed, the
walking belt will stop and the Time/Segment Time
display will begin to flash. Note: To use another
CD or video program, press the Stop button or remove the key and go to step 1 on page 17.
Measure your heart rate, if desired.
See step 6 on page 11.
7
When the program is completed, remove the
key from the console.
See step 6 on page 13.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard:
CAUTION: Always remove iFIT.com CDs and
videocassettes from your CD player or VCR
when you are finished using them.
• Make sure that the iFIT.com indicator is lit and
that the Time/Segment Time display is not
flashing. If the Time/Segment Time display is
flashing, press the Start button or the Speed
+ button on the console.
18
7
HOW TO USE PROGRAMS DIRECTLY FROM
OUR WEB SITE
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.
Hold the handrails, step onto the walking belt, and
begin walking. During the program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes.
Our Web site at www.iFIT.com allows you to access
basic programs, audio programs, and video programs
directly from the internet. Additional options are soon
to be available. See www.iFIT.com for details.
To use programs from our Web site, the treadmill must
be connected to your home computer. See HOW TO
CONNECT YOUR COMPUTER on page 16. In
addition, you must have an internet connection and
an internet service provider. A list of specific system
requirements will be found on our Web site.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the program.
Follow the steps below to use a program from our
Web site.
1
Insert the key into the console.
To stop the walking belt at any time, press the
Stop button on the console. The Time/Segment
Time display will begin to flash. To restart the program, press the Start button or the Speed + button. After a moment, the walking belt will begin to
move at 1.0 mph. When the next “chirp” is
heard, the speed and incline will change to the
next settings of the program.
See HOW TO TURN ON THE POWER on page 10.
2
Select the iFIT.com mode.
When the key is
inserted, the
manual mode will
be selected and
the Manual indicator will light. To
use a program
from our Web site, press the Program button repeatedly until the iFIT.com indicator lights.
3
Go to your computer and start an internet
connection.
4
Start your web browser, if necessary, and go to
our Web site at www.iFIT.com.
5
Follow the desired links on our Web site to select a program.
When the program is completed, the walking belt
will stop and the Time/Segment Time display will
begin to flash. Note: To use another program,
press the Stop button and go to step 5.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard, make
sure that the iFIT.com indicator is lit and that
the Time/Segment Time display is not flashing.
In addition, make sure that the audio cable is
properly connected, that it is fully plugged in,
and that it is not wrapped around a power cord.
8
Read and follow the on-line instructions for using a
program.
6
Return to the treadmill and stand on the foot
rails. Find the clip attached to the key and slide
the clip onto the waistband of your clothes.
Follow your progress with the LED track and
the displays.
See step 5 on page 10.
9
Follow the on-line instructions to start the
program.
When the program is completed, remove the
key from the console.
See step 6 on page 13.
When you start the program, an on-screen countdown will begin.
19
THE INFORMATION MODE/DEMO MODE
HOW TO ADJUST THE CUSHIONING SYSTEM
The console features an information mode that keeps
track of the total number of hours that the treadmill has
been operated and the total number of miles that the
walking belt has moved. The information mode also
allows you to switch the console from miles per hour to
kilometers per hour. In addition, the information mode
allows you to turn on and turn off the demo mode.
The treadmill features a cushioning system that reduces
the impact as you walk or run on the treadmill. The
firmness of the cushioning system is controlled by the
adjustable cushions at the center of the treadmill (there
is one adjustable cushion on each
side). To select the maximum firmness
setting, turn
Adjustable
the cushions
Cushion
to level 3; to
decrease the
firmness, turn
the cushions to level 2 or 1. It may be helpful to lift on
the walking platform as you rotate the cushion. Note:
The faster you run on the treadmill, or the heavier
your weight, the firmer the cushioning system
should be. Make sure that both cushions are at the
same setting.
To select the information mode, hold down the Stop
button while inserting the key into the console. When
the information mode is selected, the following information will be shown:
The Distance/Incline/Laps
display will show the total
number of miles that the walking belt has moved.
The Time/Segment Time display will show the total number
of hours the treadmill has been
used.
THE OPTIONAL CHEST PULSE SENSOR
An optional chest pulse sensor adds even more features to the console. The chest pulse sensor offers
hands-free operation and continuously monitors your
heart rate during your workouts. To purchase the optional chest pulse sensor, call toll-free 1-888-5331333.
An E, for English miles, or an
M, for metric kilometers, will
appear in the Speed/Min-Mile
display. Press the Speed +
button to change the unit of
measurement.
IMPORTANT: The Calories/
Fat Calories/Heart Rate display should be blank. If a “d”
appears in the display, the
console is in the “demo” mode.
This mode is intended to be
used only when a treadmill is displayed in a store.
When the console is in the demo mode, the power cord
can be plugged in, the key can be removed from the
console, and the displays and indicators on the console
will automatically light in a preset sequence, although
the buttons on the console will not operate. If a “d” appears in the Calories/Fat Calories/Heart Rate display when the information mode is selected, press
the Speed – button so the display is blank.
To exit the information mode, remove the key from the
console.
20
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
1
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be
damaged. Make sure the adjustable cushion is in a set
position (see page 20). Next, unplug the power cord.
CAUTION: You must be able to safely lift 45 pounds (20
kg) in order to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. CAUTION: To decrease the possibility of injury, bend your legs and keep your back straight. As
you raise the treadmill, make sure to lift with your legs
rather than your back. Raise the treadmill about halfway
to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob to
the left and hold it. Raise the treadmill until the latch pin is
aligned with the hole in the catch. Insert the latch pin into
the catch. Make sure that the latch pin is fully inserted
into the catch.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the storage position in temperatures above 85° Fahrenheit.
2
Knob
Catch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the pin
on the lock knob is inserted into the slot in the catch.
Pulse Bar
1. Hold the handrails as shown and place one foot against a
wheel. It may be helpful to grab the pulse bar as you tip
the treadmill.
2. Tilt the treadmill back until it rolls freely on the front wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
Base
3. Place one foot on the base, and carefully lower the treadmill until it is resting in the storage position.
Front Wheels
HOW TO LOWER THE TREADMILL FOR USE
1. Refer to drawing 2 above. Hold the upper end of the treadmill with your right hand as shown. Using your left
hand, pull the lock knob to the left and hold it. Pivot the treadmill down until the frame is past the pin on the lock
knob. Note: You may need to push the handrail to the side slightly.
2. Refer to drawing 1 above. Hold the treadmill firmly with both hands, and lower the treadmill to the floor.
CAUTION: To decrease the possibility of injury, bend your legs and keep your back straight.
21
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department tollfree at 1-888-533-1333, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppressor
that meets all of the specifications described on page 8. Important: The treadmill is not compatible
with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the treadmill
near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
c
d. Check the on/off switch located on the treadmill
near the power cord. The switch must be in the on
position.
d
Tripped
Reset
On
Position
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the
circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. Make sure that the on/off switch is in the on position.
e. If the treadmill still will not run, please call our Customer Service Department, toll-free.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and unplug the
power cord. Carefully tip the treadmill down as
shown in drawing a. Remove the Screws (39, 83) from
the hood. Raise the Uprights (69) and carefully remove the hood.
a
39
69
Locate the Reed Switch (10) and the Magnet (7) on
the left side of the Pulley (8). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 1/8”. If necessary, loosen the 1/2”
Screw (67) and move the Reed Switch slightly.
Retighten the Screw. Re-attach the hood, and run the
treadmill for a few minutes to check for a correct
speed reading.
22
1/8”
67
10
Top
View
83
8
7
PROBLEM: The thumb pulse sensor does not function properly
SOLUTION: a. Wash your hands before to using the pulse sensor. In addition, keep the pulse sensor clean using
a damp cloth and a small amount of mild detergent.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 8.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
rear roller adjustment bolts counterclockwise, 1/4 of a
turn. When the walking belt is properly tightened, you
should be able to lift each side of the walking belt 3 to
4 inches off the walking platform. Be careful to keep
the walking belt centered. Plug in the power cord, insert the key and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
b
3”–4”
Rear Roller Adjustment Bolts
c. If the walking belt still slows, please call our Customer Service Department, toll-free.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key and
UNPLUG THE POWER CORD. If the walking belt has
shifted to the left, use the allen wrench to turn the left
rear roller bolt clockwise 1/2 of a turn; if the walking belt
has shifted to the right, turn the bolt counterclockwise
1/2 of a turn. Be careful not to overtighten the walking
belt. Plug in the power cord, insert the key and run the
treadmill for a few minutes. Repeat until the walking belt is
centered.
b. If the walking belt slips when walked on, first remove the
key and UNPLUG THE POWER CORD. Using the allen
wrench, turn both rear roller bolts clockwise, 1/4 of a turn.
When the walking belt is correctly tightened, you should
be able to lift each side of the walking belt 3 to 4 inches off
the walking platform. Be careful to keep the walking belt
centered. Plug in the power cord, insert the key and carefully walk on the treadmill for a few minutes. Repeat until
the walking belt is properly tightened.
a
b
PROBLEM: The incline of the treadmill does not change correctly or does not change when iFIT.com
CD’s and videos are played
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, remove the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline.
23
CONDITIONING GUIDELINES
uses easily accessible carbohydrate calories for energy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the treadmill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your exercise program. Remember—these are general guidelines only. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up increases your body temperature, heart rate and circulation in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “training zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-exercise problems.
To measure your heart rate during exercise, use the
pulse sensor on the console. If your heart rate is too
high or too low, adjust the speed and incline of the
treadmill.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
The key to success is to make exercise a regular and
enjoyable part of your everyday life.
24
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
1
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times. Stretches: Hamstrings, back of knees
and back.
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot toward you and rest it against the inner thigh of your extended leg.
Reach toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times for each leg. Stretches: Hamstrings,
lower back and groin.
2
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat
3 times for each leg. To cause further stretching of the achilles
tendons, bend your back leg as well. Stretches: Calves, achilles
tendons and ankles.
3
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your
buttocks as possible. Hold for 15 counts, then relax. Repeat 3
times for each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and
hip muscles.
25
5
NOTES
26
PART LIST—Model No. PFTL99602
R0804A
To locate the parts listed below, refer to the EXPLODED DRAWING attached in the center of this manual.
Key
No. Qty.
1
2
3
4
5
6
7
8
9
10
2
2
2
1
2
2
1
1
8
1
11*
12
13
14
15*
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
1
1
1
1
1
1
1
1
1
1
1
1
1
2
4
1
5
2
1
1
1
1
4
4
1
1
1
1
10
40
41
42
43
44
45
2
1
1
1
1
4
Description
Foot Rail Insert
Foot Rail
Foot Rail Cap Screw
Left Foot Rail Cap
Frame Pivot Bolt
Frame Pivot Spacer
Magnet
Front Roller/Pulley
Frame Pivot Nut
Reed Switch/Sensor
Wire
Latch Assembly
Reed Switch Clip
Lift Frame
Star Washer
Motor Assembly
Motor
Pulley/Flywheel/Fan
Motor Belt
Motor Pivot Nut
Motor Tension Nut
Motor Tension Bolt
Motor Pivot Bolt
Hood
Incline Motor Bolt
Plastic Stand-off
Power Board
Screw
Ball Detent
Controller
Electronics Plate
Motor/Controller Wire
Front Roller Adj. Bolt
1 1/4” Screw
Roller Washer
Front Roller Nut
Incline Motor
Incline Motor Stop
Belly Pan
Belly Pan Screw
(Long)
Static Decal
Circuit Breaker
Power Cord
On/Off Switch
Left Endcap Insert
Belt Guide Screw
Key
No. Qty.
46
47
48
49
50
51
52
53
54
1
2
2
16
1
1
1
4
2
55
56
1
5
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
1
1
2
1
1
1
2
2
1
2
8
1
1
1
1
2
1
1
1
1
2
2
2
4
1
1
10
1
1
1
14
1
1
1
Description
Belt Guide
Front Isolator
Adjustable Cushion
Fastener
Belly Pan
Right Foot Rail Cap
Walking Platform
Platform Screw
Adjustable Cushion
Screw
Video Wire Nut
Ground Screw/
Controller Screw
Ground Wire
Rear Endcap
Rear Roller Adj. Bolt
Warning Decal
Allen Wrench
Rear Roller
Rear Isolator
Cushion Spacer
Left Foam Grip
Handrail Extension
1/2” Screw
Lock Knob
Upright
Lock Knob Sleeve
Spring
Lock Pin Collar
Pin Clip
Lock Pin
Right Foam Grip
Pulse Bar
Pulse Bar Washer
Pulse Bar Bolt
Upright Endcap
Belly Pan Screw
Console Base
Console
Console Screw
Key/Clip
IFIT.com Wire
Jack
Console Back Screw
Console Back
Releaseable Tie
Cable Tie Screw
27
Key
No. Qty.
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106*
1
4
2
2
2
1
1
1
4
8
1
2
2
2
1
2
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
#
#
#
#
#
#
#
#
1
1
1
1
2
1
1
1
1
1
2
2
2
2
2
1
1
1
1
1
1
1
1
1
Description
Cable Tie Clamp
8” Cable Tie
Lift Pivot Bolt
Wheel Bolt
Wheel
Right Endcap Insert
Grommet
Upright Wire Harness
Base Pad
3/4” Screw
Motor Washer
Extension Leg
Extension Cap
Incline Warning Decal
Shock
Extension Leg
Assembly
Chest Pulse Wire
Book Holder
Power Cord Grommet
Frame
Catch Screw
Catch
Audio Wire
Walking Belt
30” Wire Harness
20” Wire Harness
Hand Weight
Endcap Spacer
Thick Base Pad
Cushion Bolt
Long Hood Screw
Filter Wire
8” Black Wire, M/F
4” Black Wire, 2F
8” White Wire, 2F
4” Blue Wire, 2F
8” Red Wire, M/F
12” Green Wire, 2/Ring
8” Green Wire, F/Ring
User's Manual
* Includes all parts shown in box
# These parts are not illustrated
59
34
61
60
44
59
118
110
63
49
34
53
118
120
64
48
28
96
34
54
58
111
1
62
112
56
57
53
49
111
47
2
3
4
63
54
53
5
2
49
1
6
8
120
64
114
7
52
34
28
48
53
10
18
49
50
9
17
19
111
3
12
67
15*
49
51
EXPLODED DRAWING—Model No. PFTL99602
9
37
13 14
9
16
47
24
36
20
9
83
14
9
22
35
24
46
45
101
R0804A
6
80
32
21
38
80
25
5
9
31
83
26
39
113
25
41
55
80
40
30
56
27
122
43
109
42
29
39
106*
103
65
33
102
99
100
11*
66
104
68
67
78
100
77
73
105
14
71
106*
93
72
70
69
103
74
95
66
33
100
99
104
76
102
100
99
94
75
79
9
33
67
98
100
107
97
77
92
78
79
100
99
9
94
93
95
33
81
91
90
89
EXPLODED DRAWING—Model No. PFTL99602
119
87
82
87
83
87
108
121
87
40
87
83
R0804A
87
88
87
87
84
23
115
85
121
86
117
116
ORDERING REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-888-533-1333, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). When ordering parts, please be prepared to give
the following information:
• The MODEL NUMBER OF THE PRODUCT (PFTL99602)
• The NAME OF THE PRODUCT (PROFORM® 995 SEL treadmill)
• The SERIAL NUMBER OF THE PRODUCT (see the front cover of this manual)
• The KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the PART LIST on page 27 and the EXPLODED
DRAWING attached in the center of this manual).
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not
extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized service center; products used for commercial or rental purposes; or products used as store display models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 214443 R0804A
Printed in USA © 2004 ICON IP, Inc.