Craftsman 315.112170 Operator`s manual

PERATOR'S
MANUAL
T
®
RANDOM ORBIT SANDER
DOUBLE iNSULATED
Model Nos.
315.112180
315.112170
A
WARNING:
To reduce the risk of injury,
the user must read and understand the
operator's manual before using this product.
Craftsman
Consumer
Helpline:
1-800-932-3188
Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman
Visit the Craftsman web page: www.sears.com/craftsman
987000-101
1-23-07 (REV:00)
Save this
manual
Estates, IL 60179 USA
for future
reference
[] Warranty ..........................................................................................................................................................................
2
[] Introduction .....................................................................................................................................................................
2
[] General Safety Rules ....................................................................................................................................................
3-4
[] Specific Safety Rules .......................................................................................................................................................
4
[] Symbols ........................................................................................................................................................................
5-6
[] Electrical ..........................................................................................................................................................................
7
[] Features ...........................................................................................................................................................................
8
[] Assembly .........................................................................................................................................................................
9
[] Operation ....................................................................................................................................................................
9-11
[] Maintenance ..................................................................................................................................................................
12
[] Accessories ...................................................................................................................................................................
12
[] Exploded View and Parts List ...................................................................................................................................
[] Parts Ordering/Service
.....................................................................................................................................
ONE-YEAR FULL WARRANTY
ON CRAFTSMAN
13-14
Back Page
TOOL
If this Craftsman tool fails to give complete satisfaction within one year from date of purchase, RETURN iT TO ANY
SEARS STORE OR OTHER CRAFTSMAN OUTLET iN THE UNITED STATES FOR FREE REPLACEMENT.
If this Craftsman tool is used for commercial
purchase.
or rental purposes, this warranty applies for only 90 days from the date of
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Sears, Roebuck and Co., Noffman Estates, IL 60179
This product has many features for making its use more pleasant and enjoyable. Safety, performance,
have been given top priority in the design of this product making it easy to maintain and operate.
and dependability
A
WARNING:
Read and understand all instructions. Failure to follow all instructions listed below,
may result in electric shock, fire and/or serious
personal injury.
SAVE THESE
WORK
INSTRUCTIONS
AREA
[] Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
[] Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
[] Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
ELECTRICAL
SAFETY
[] Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This
plug will fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug.
if it still does not fit, contact a qualified electrician
to install a polarized outlet. Do not change the plug
in any way. Double insulation [] eliminates the need
for the three-wire grounded power cord and grounded
power supply system.
[] Avoid body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerators. There is an
increased risk of electric shock if your body is grounded.
[] Don't expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
[] Do not abuse the cord. Never use the cord to carry
the tools or pull the plug from an outlet. Keep cord
away from heat, oil, sharp edges, or moving parts.
Replace damaged cords immediately. Damaged
cords increase the risk of electric shock.
[] When operating a power tool outside, use an outdoor
extension cord marked "W-A" or "W". These cords
are rated for outdoor use and reduce the risk of electric
shock.
PERSONAL
SAFETY
[] Stay alert, watch what you are doing and use common sense when operating a power tool. Do not
use tool while tired or under the influence of drugs,
alcohol, or medication. A moment of inattention while
operating power tools may result in serious personal
injury.
[] Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair, clothing,
and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
[] Avoid accidental starting. Be sure switch is off before
plugging in. Carrying tools with your finger on the switch
or plugging in tools that have the switch on invites
accidents.
[] Remove adjusting keys or wrenches before turning
the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
[] Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enables better
control of the tool in unexpected situations.
[] Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
[] Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
[] Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
tool in unexpected situations.
TOOL USE AND
[] Use clamps
support the
the work by
may lead to
CARE
or other practical way to secure and
workpiece to a stable platform. Holding
hand or against your body is unstable and
loss of control.
[] Do not force tool. Use the correct tool for your application. The correct tool will do the job better and
safer at the rate for which it is designed.
[] Do not use tool if switch does not turn it on or off.
Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
[] Disconnect the plug from power source before
making any adjustments,
changing accessories,
or storing the tool. Such preventive safety measures
reduce the risk of starting the tool accidentally.
[] Store idle tools out of the reach of children and
other untrained persons. Tools are dangerous in the
hands of untrained users.
[] Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools with sharp cutting edges are less likely to bind and are easier to
control.
[] Check for misalignment
or binding of moving parts,
breakage of parts, and any other condition that
may affect the tool's operation. If damaged, have
the tool serviced before using. Many accidents are
caused by poorly maintained tools.
[] Use only accessories that are recommended
by the
manufacturer for your model. Accessories that may
be suitable for one tool, may become hazardous when
used on another tool.
[] Keep the tool and its handle dry, clean and free
from oil and grease. Always use a clean cloth when
cleaning. Never use brake fluids, gasoline, petroleumbased products, or any strong solvents to clean your
tool. Following this rule will reduce the risk of loss of
control and deterioration of the enclosure plastic.
SERVICE
[] Tool service must be performed only by qualified
repair personnel. Service or maintenance performed
by unqualified personnel may result in a risk of injury.
[] Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with
a "live" wire will make exposed metal parts of the cutting tool "live" and shock the operator.
[] Know your power tool. Read operator's manual
carefully. Learn its applications and limitations, as
well as the specific potential hazards related to this
tool. Following this rule will reduce the risk of electric
shock, fire, or serious injury.
[] Always wear safety glasses. Everyday eyeglasses
have only impact-resistant
lenses; they are NOT
safety glasses. Following this rule will reduce the risk
of serious personal injury.
[] Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
[] Protect your hearing. Wear hearing protection during extended periods of operation. Following this rule
will reduce the risk of serious personal injury.
[] Inspect tool cords periodically and, if damaged,
have repaired at your nearest Sears or other qualified service center. Constantly stay aware of cord
location. Following this rule will reduce the risk of
electric shock or fire.
[] Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should
be carefully checked to determine that it will
,_lll_ WARNING:
[] When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or
failure to follow Maintenance Instructions may create a
risk of shock or injury.
operate properly and perform its intended function. Check for alignment of moving parts, binding
of moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation.
A guard or other part that is damaged should be
properly repaired or replaced by an authorized service center. Following this rule will reduce the risk of
shock, fire, or serious injury.
[] Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. A wire gauge size (A.W.G.) of at least 16 is
recommended for an extension cord 50 feet or less
in length. A cord exceeding 50 feet is not recommended, if in doubt, use the next heavier gauge.
The smaller the gauge number, the heavier the
cord. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
[] inspect for and remove all nails from lumber before
using this tool. Following this rule will reduce the risk
of serious personal injury.
[] Ifthepowersupplycord
isdamaged, it must be replaced
only by the manufacturer or by an authorized service
center to avoid risk.
[] Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If
you loan someone this tool, loan them these instructions also.
Some dust created by power sanding, sawing, grinding, drilling, and other construction
contains chemicals known to cause cancer, birth defects or other reproductive
chemicals are:
activities
harm. Some examples of these
• lead from lead-based paints,
crystalline silica from bricks and cement and other masonry products, and
arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
Someofthefollowingsymbolsmaybeusedonthis product.Pleasestudythemandlearntheirmeaning.Proper
interpretation
ofthesesymbolswillallowyouto operatethe productbetterandsafer.
SYMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
A
Amperes
Current
mz
Hertz
Frequency (cycles per second)
W
Watt
Power
min
Minutes
Time
Alternating Current
Type of current
Direct Current
Type or a characteristic
no
No Load Speed
Rotational speed, at no load
[]
Class II Construction
Double-insulated
.../min
Per Minute
Revolutions, strokes, surface speed, orbits etc., per minute
@
Wet Conditions Alert
Do not expose to rain or use in damp locations.
Read The Operator's Manual
To reduce the risk of injury, user must read and understand
operator's manual before using this product.
Eye Protection
Always wear safety goggles or safety glasses with side shields and,
as necessary, a full face shield when operating this product.
Safety Alert
Precautions that involve your safety.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
Failure to keep your hands away from the blade will result in
serious personal injury.
Hot Surface
To reduce the risk of injury or damage, avoid contact with any
hot surface.
=.--=.#_
O
A
@
@
@
®
of current
construction
Thefollowingsignalwordsandmeanings
areintendedto explainthe levelsof riskassociatedwiththis product.
SYMBOL
_,
SIGNAL
MEANING
DANGER:
Indicates
imminently
in death oranserious
injury.hazardous situation, which, if not avoided, will result
WARNING:
Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
CAUTION:
Indicates
a potentially
hazardous situation, which, if not avoided, may result in
minor or moderate
injury.
CAUTION:
(Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
SERVICE
Servicing requires extreme care and knowledge and
should be performed only by a qualified service technician. For service we suggest you return the product to
your nearest SEARS PARTS AND REPAIR SERVICE
CENTER for repair. When servicing, use only identical
replacement parts.
_k,
A
WARNING:
To avoid serious personal injury, do not
attempt to use this product until you read thoroughly
and understand completely the operator's manual.
If you do not understand the warnings and instructions in the operator's manual, do not use this
product. Call the Craftsman Consumer Helpline at
1-800-932-3188 for assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which
can result in severe eye damage. Before beginning power tool operation, always wear safety
goggles or safety glasses with side shields and, when needed, a full face shield. We recommend
Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields.
Always use eye protection which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
DOUBLE
INSULATION
Double insulation is a concept in safety in electric power
tools, which eliminates the need for the usual three-wire
grounded power cord. All exposed metal parts are
isolated from the internal metal motor components with
protecting insulation. Double insulated tools do not need
to be grounded.
A
WARNING:
The double insulated system is
intended to protect the user from shock resulting
from a break in the tool's internal insulation. Observe
all normal safety precautions to avoid electrical
shock.
NOTE: Servicing of a product with double insulation
requires extreme care and knowledge of the system and
should be performed only by a qualified service technician. For service, we suggest you return the product to
your nearest Sears or other qualified service center for
repair. Always use original factory replacement parts when
servicing.
ELECTRICAL
EXTENSION
CORDS
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the product will draw.
An undersized cord will cause a drop in line voltage, resuiting in overheating and loss of power. Use the chart to
determine the minimum wire size required in an extension
cord. Only round jacketed cords listed by Underwriter's
Laboratories (UL) should be used.
When working outdoors with a product, use an extension
cord that is designed for outside use. This type of cord is
designated with "WA" on the cord's jacket.
Before using any extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
**Ampere rating (on product faceplate)
0-2.0
2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length
Wire Size (A.W.G.)
25'
16
16
16
16
14
14
50'
16
16
16
14
14
12
100'
16
16
14
12
10
--
CONNECTION
This product has a precision-built electric motor. It should
be connected to a power supply that is 120 volts, 60 Hz,
AC only (normal household current). Do not operate this
product on direct current (DC). A substantial voltage drop
will cause a loss of power and the motor will overheat. If
the product does not operate when plugged into an outlet,
double-check the power supply.
**Used on 12 gauge - 20 amp circuit
NOTE: AWG = American Wire Gauge
A
A
WARNING:
Keep the extension cord clear of the
working area. Position the cord so that it will not get
caught on lumber, tools or other obstructions while
you are working with a power tool. Failure to do so
can result in serious personal injury.
WARNING:
Check extension cords before each
use. If damaged replace immediately. Never use
product with a damaged cord since touching the
damaged area could cause electrical shock resulting
in serious injury.
PRODUCTSPECIFiCATiONS
SandingPad..................................................................................................................................
5 in.Hook-and-Loop
Type
NoLoadSpeed
Model315.112180
..................................................................................................................
7,000-12,500
r/rain.(RPM)
Model315.112170
.............................................................................................................................
13,000r/rain.(RPM)
Input
Model315.112180
..........................................................................................................
120Volts,60Hz,AC,2.8Amps
Model315.112170
..........................................................................................................
120Volts,60Hz,AC,2.4Amps
Motion...........................................................................................................................................................
RandomOrbital
NetWeight...................................................................................................................................................
3-3/4Ibs.(1.7kg)
TOP VIEW OF MODELNO. 315.112180
VIEW OFMODEL NO. 315.112170
TO DECREASE
SPEED
TO
TURN OFF
VARIABLESPEEDSWITCH
ON/OFF
SLIDE
SWITCH
TO iNCREASE
SPEED
DUSTBAG
ASSEMBLY
TO
TURN ON
BACKING
ON/OFFSLIDE SWITCH
SANDINGDiSC
PAD
Fig. 1
KNOW YOUR SANDER
RANDOM
See Figure 1,
The random orbit motion provides overlapping sanding
movements by combining orbital and spinning motion.
The safe use of this product requires an understanding
of the information on the product and in this operator's
manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself
with all operating features and safety rules.
ON/OFF
SLIDE SWITCH
This sander is equipped with a simple slide switch control.
VARIABLE
ORBIT
SPEED
SWITCH
(MODEL 112180 ONLY}
The variable speed feature allows the sander to operate
at speeds that can be adjusted by rotating the dial on the
variable speed switch from A to R
UNPACKING
Thisproducthasbeenshippedcompletelyassembled.
[] Carefullyremovetheproductandanyaccessories
from
the box.Makesurethatallitemslistedinthe packing
listareincluded.
_,
WARNING:
If any parts are damaged or missing
do not operate this product until the parts are
replaced. Failure to heed this warning could result
in serious personal injury.
,A,
[] Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
[] Do not discard the packing material until you have carefully inspected and satisfactorily operated the product.
WARNING:
Do not attempt to modify this product
or create accessories not recommended for use with
this product. Any such alteration or modification is
misuse and could result in a hazardous condition
[] If any parts are damaged or missing, please call
1-800-932-3188 for assistance.
leading to possible serious personal injury.
PACKING
Sander
LIST
A
WARNING:
Do not connect to power supply until
assembly is complete. Failure to comply could result
in accidental starting and possible serious injury.
Sanding Disc
Dust Bag
Operator's Manual
A
A
WARNING:
Do not allow familiarity with this product to make you careless. Remember that a careless
fraction of a second is sufficient to inflict serious
injury.
WARNING:
Always wear safety goggles or safety
glasses with side shields when operating power
tools. Failure to do so could result in objects being
thrown into your eyes resulting in possible serious
injury.
You may use this product for the purposes listed below:
[] Sanding on wood surfaces
[] Removing rust from and sanding metal surfaces
SANDING
TYPE
See Figure 2.
[] Unplug the sander.
[] Align the holes in the sanding disc with the holes in the
hook-and-loop backing pad.
NOTE: Holes in sanding disc must line up with holes in
the backing pad in order for the dustless feature of the
sander to function properly.
[] Press the sanding disc against the backing pad as
firmly as possible.
APPLICATIONS
SELECTING
ATTACHING HOOK=AND=LOOP
SANDING DISCS
DISCS
Selecting the correct size grit and type sanding disc is
an extremely important step in achieving a high quality
sanded finish. Aluminum oxide, silicon carbide, and other
synthetic abrasives are best for power sanding. Natural
abrasives, such as flint and garnet are too soft for use in
power sanding.
NOTE: For best adhesion, we recommend that you
clean the backing pad and the sanding disc backing occasionally by brushing them lightly with a small
brush.
H00K-AND-L00P
SANDINGDISC
BACKING
PAD
In general, coarse grit will remove the most material and
finer grit will produce the best finish in all sanding operations. The condition of the surface to be sanded will determine which grit will do the job. If the surface is rough, start
with a coarse grit and sand until the surface is uniform.
Medium grit may then be used to remove scratches left by
the coarser grit and finer grit used for finishing of the surface. Always continue sanding with each grit until surface
is uniform.
Fig. 2
DUSTLESS
A
SANDING
See Figures 3 - 4.
_lh WARNING:
Do not use the dust bag when sanding
metal. Using the dust bag when sanding metal
creates a fire hazard, which could damage the tool
and lead to serious personal injury.
SANDER
WARNING:
Collected sanding dust from sanding
surface coatings such as polyurethanes, linseed
oil, etc., can self-ignite in the sander dust bag or
elsewhere and cause fire. To reduce the risk of fire,
always empty the dust bag frequently while sanding.
Never store or leave a sander without totally emptying its dust bag (see Cleaning Dust Bag Assembly
in the Maintenance section of this manual). Also
follow the recommendations of the coatings manufactu rers.
ATTACHING
SANDER
TO VACUUM
See Figure 5.
When sanding for an extended period of time, you can
easily attach the dust collection system of the sander to a
vacuum.
To attach:
[] Unplug the sander.
[] Remove dust bag from sander.
[] Attach vacuum hose to dust exhaust.
NOTE: Vacuum hose fits inside dust exhaust.
DUSTBAG
[] Connect sander and vacuum to power supply.
DUST EXHAUST
,_,
WARNING:
Do not wear loose clothing or jewelry
when operating sander. They could get caught in
moving parts causing serious injury. Keep head away
from sander and sanding area. Hair could be drawn
into sander causing serious injury.
Fig. 3
The dust bag assembly provides a dust collection system
for the sander. It can be installed by slipping the bag over
the dust exhaust with a twisting motion. Sanding dust is
drawn up through the holes of the sanding disc to collect
in the dust bag during sanding operation.
NOTE: For more efficient operation, empty dust bag
when no more than half full. This will permit the air to flow
through the bag better.
VACUUMHOSE
DUSTEXHAUST
Fig. 4
10
Fig. 5
A
A
Do not force. The weight of the unit supplies adequate
pressure, so let the sanding disc and sander do the work.
Applying additional pressure only slows the motor, rapidly
wears sanding disc, and greatly reduces sander speed.
Excessive pressure will overload the motor causing possible damage from motor overheating and can result in
inferior work. Any finish or resin on wood may soften from
the frictional heat. Do not allow sanding on one spot too
long as the sander's rapid action may remove too much
material, making the surface uneven.
WARNING"
Before connecting the sander to power
supply source, always check to be sure the switch is
in the OFF position. Failure to do so could result in
accidental starting of the sander resulting in possible
serious injury.
CAUTION:
air vents.
ON/OFF
SLIDE
Be careful not to let your hand cover the
SWITCH
Extended periods of sanding may tend to overheat the
motor. If this occurs, turn sander off and wait until sanding disc comes to a complete stop, then remove it from
workpiece. Remove your hand from vent area, remove
sanding disc, then with your hand removed from vent
area, turn sander on and run it free without a load to cool
motor.
This sander is equipped with a simple slide switch control.
To turn the sander ON, slide the switch in the direction
shown by the arrow in figure 1. To turn the sander OFF,
slide the switch in the opposite direction.
VARIABLE SPEED SWITCH
(MODEL 112180 ONLY}
The variable speed feature allows the sander to operate
at speeds that can be adjusted by rotating the dial on the
variable speed switch from A to R The dial is conveniently
located on the motor housing, allowing operator control of
disc speed. To increase sanding disc speed, turn the dial
on the variable speed switch to a higher setting. Turn dial
to a lower setting to decrease sanding disc speed.
Flush sanding can be performed with the sander. The front
edge of the sander allows flush sanding. Upon completion
of sanding operation, turn sander off and wait until sanding disc comes to a complete stop before removing from
workpiece.
_I_
SANDING
To ensure proper brake operation after
extended use, periodically check its operation by
removing the sanding disc and running the sander
without load (off the workpiece). The backing pad
should not take longer than 6 seconds to stop. If
it takes longer than 6 seconds to stop, then brake
should be replaced.
See Figures 6 - 7.
Clamp or otherwise secure the work to prevent it from
moving under the sander.
_IL WARNING:
CAUTION:
Unsecured work could be thrown
towards the operator causing injury.
Place sander on workpiece so that all of sanding disc
surface is in contact with workpiece. Start the sander and
move it slowly over workpiece making successive passes
in parallel lines, circles, or crosswise movements. Upon
completion of sanding operation, turn sander off and
wait until sanding disc comes to a complete stop before
removing from workpiece.
NOTE: The brake is available and can be purchased
through Replacement Parts at your nearest Sears Service
Center.
Fig. 7
Fig. 6
11
A
A
CLEANING
WARNING:
When servicing, use only identical
Craftsman replacement parts. Use of any other parts
may create a hazard or cause product damage.
_!1_11=
WARNING:
Collected sanding dust from sanding
surface coatings such as polyurethanes, linseed
oil, etc., can self-ignite in the sander dust bag or
elsewhere and cause fire. To reduce the risk of fire,
always empty the dust bag frequently while sanding.
Never store or leave a sander without totally emptying its dust bag. Also follow the recommendations of
the coatings manufacturers.
WARNING:
Always wear safety goggles or safety
glasses with side shields during power tool operation
or when blowing dust. If operation is dusty, also wear
a dust mask.
GENERAL
DUST BAG ASSEMBLY
See Figures 8 - 9,
MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
For more efficient operation, empty dust bag when no
more than half full. This will permit the air to flow through
the bag better.
To empty the dust bag:
,_
WARNING"
Do not at any time let brake fluids,
[] Unplug the sander.
gasoline, petroleum-based products, penetrating
oils, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which
may result in serious personal injury.
[] Remove dust bag from sander.
[] Remove dust bag from frame, and shake out dust.
[] Replace dust bag over frame then install dust bag on
sander.
Electric tools used on fiberglass material, wallboard,
spackling compounds, or plaster are subject to accelerated wear and possible premature failure because the
fiberglass chips and grindings are highly abrasive to bearings, brushes, commutators, etc. Consequently, we do
not recommend using this product for extended work on
these types of materials. However, if you do work with any
of these materials, it is extremely important to clean the
product using compressed air.
DUSTBAG
/
Fig. 8
LUBRICATION
DUSTBAG
All of the bearings in this product are lubricated with a
sufficient amount of high grade lubricant for the life of
the unit under normal operating conditions. Therefore, no
further lubrication is required.
FRAME
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts
should be replaced at a Sears Service Center.
Fig. 9
Look for these accessories at Sears retail:
[] 5 in. Sanding Disc-
Fine
[] 5 in. Sanding Disc-
Medium
[] 5 in. Sanding Disc-
Coarse
_1_ WARNING:
Current attachments and accessories available for use with this product are listed above. Do not use
any attachments or accessories not recommended by the manufacturer of this product. The use of attachments
accessories not recommended can result in serious personal injury.
12
or
--
CRAFTSMAN
See Note
SANDER
"A"
- MODEL
on next
NOS. 315.112180
page
1
\
3
13
AND 315.112170
_,
CRAFTSMAN
SANDER
- MODEL
NOS. 315.112180
AND 315.112170
,_
J
model
number
in all will
correspondence
your SANDER
or when
ordering
repairmention
parts. the
The model
number
be found on aregarding
plate attached
to the motor
housing.
Always
SEE BACK PAGE FOR PARTS ORDERING
INSTRUCTIONS
PARTS LIST
Key
No.
Part
NO.
Description
039157006002
039157005003
Data Label (Model No. 315.112180) ............................................
1
Data Label (Model No. 315.112170) ............................................
1
2
030157001021
Dust Bag Assembly (Includes Key No. 13) ..................................
1
3
030157001002
030157002002
Logo Label (Model No. 315.112180) ...........................................
Logo Label (Model No. 315.112170) ...........................................
1
1
4
030157001012
Fan ..............................................................................................
1
5
030157001013
Bearing Cap w/Bearing ...............................................................
1
6
030157001017
Brake ...........................................................................................
1
7
030157001018
Braking Pad ................................................................................
1
8
030157001019
Screw (M5 x 6 mm Pan Hd.) .......................................................
4
Sanding Disc ...............................................................................
1
9
Qty.
10
030157001016
Screw (M4 x 10 mm Pan Hd.) .....................................................
1
11
030157001015
Lock Washer ................................................................................
1
12
030157001014
Washer ........................................................................................
1
13
030157001023
Dust Bag ......................................................................................
1
987000101
Operator's Manual
NOTE "A": The assembly shown represents an important part of the double insulated system. To avoid the
possibility of alteration or damage to the system, service should be performed by the nearest
Sears repair center. Contact the nearest Sears retail store for service center information.
* Standard Hardware
*** Complete
assortment
item = May Be Purchased Locally
is available
14
at your nearest Sears retail store.