Regency Fireplace Products P33-4 Installation manual

www.regency-fire.com
P33-3 Zero Clearance
Direct Vent Gas Fireplace
MODELS:
P33-NG3 Natural Gas
Owners &
Installation Manual
P33-LP3 Propane
WARNING:
FOR YOUR SAFETY
If the information in these instructions are not followed exactly, What to do if you smell gas:
a fire or explosion may result causing property damage,
Do not try to light any appliance
personal injury or loss of life.
Do not touch any electrical switch:
do not use any phone in your
FOR YOUR SAFETY
building.
Do not store or use gasoline or other flammable vapors and
Immediately call your gas supplier
liquids in the vicinity of this or any other appliance.
from a neighbour's phone. Follow
the gas supplier's instructions.
Installation and service must be performed by a qualified
If
you cannot reach your gas
installer, service agency or the gas supplier.
supplier, call the fire department.
Tested by:
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
918-262a
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD.
6988 Venture St., Delta, BC Canada, V4G 1H4
01/04/06
To the New Owner:
Congratulations!
You are the owner of a state-of-the-art Gas Stove by FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. The
P33-3 has been designed to provide you with all the warmth and charm of a wood fireplace at the flick of a switch.
The P33-3 has been approved by Warnock Hersey for both safety and efficiency. As it also bears our own mark,
it promises to provide you with economy, comfort and security for many trouble free years to follow. Please take a
moment now to acquaint yourself with these instructions and the many features of your Regency Fireplace.
INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE
This Regency product has been tested and listed by Warnock Hersey as a Direct Vent Wall Furnace to the following standards: VENTED GAS FIREPLACE HEATERS ANSI Z21.88-2002/CSA 2.33-2002 and GAS-FIRED APPLIANCES FOR USE AT HIGH ALTITUDES CAN/CGA-2.17-M91.
This Direct Vent System Appliance must be installed in accordance with the manufacturer's installation instructions and the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard of Fire Safety Criteria for Manufactured Home Installations,
Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240-MH Mobile Home Standard in Canada.
This appliance installation must comply with the manufacturer's installation instructions and local codes, if any. In the absence of local codes follow
the current National Fuel Gas Code, ANSI Z223.1 and the current National Electrical Code ANSI/NFPA 70 in the U.S.A., and the current CAN/CGA
B149 Gas Installation Code and the current Canadian Electrical Code CSA C22.1 in Canada.
The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National
Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.
Ensure that structural members are not cut or weakened during installation.
This Regency Mobile/Manufactured Home Listed
appliance comes factory equipped with a means
to secure the unit.
This Regency Mobile/Manufactured Home listed
appliance comes equipped with a dedicated #8
ground lug to which an 18 gauge copper wire from
the steel chassis ground must be attached.
This appliance may be installed in an aftermarket permanently located, manufactured (mobile)
home, where not prohibited by local codes.
This appliance is only use with the type of gas
indicated on the rating plate. This appliance is
not convertible for use with other gases, unless
a certified kit is used.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
TABLE OF CONTENTS
P33-3 ZERO CLEARANCE
DIRECT VENT GAS FIREPLACE
Page
Safety Label
Safety Label ............................................................... 4
Installation
Important Message ..................................................... 5
Before You Start ......................................................... 5
General Safety Information ........................................ 5
Manufactured Home Additional Requirements ........... 5
Installation Checklist ................................................... 6
Unit Dimensions ......................................................... 6
HeatWave Duct System Option .................................. 6
Locating Your Gas Stove ............................................ 6
Clearances ................................................................. 7
Combustible Mantel Clearances ................................ 7
Mantel Leg Clearances .............................................. 7
Framing and Finishing ................................................ 8
Unit Assembly Prior to Installation .............................. 9
Venting Introduction .................................................... 9
Exterior Vent Termination Locations ......................... 10
Venting - Regency Direct Vent System (Flex)
Horizontal Terminations only .....................................11
Venting - Installation of Regency Direct Vent
System (Flex) ..................................................... 12
Venting - Rigid Pipe Venting Systems ...................... 13
Rigid Pipe Venting Components List ........................ 14
Venting Arrangements - Vertical Terminations .......... 15
Venting Arrangements - Horizontal Terminations .... 17
Vertical Terminations - Co-Linear Flex System......... 21
Venting Arrangements .............................................. 22
Venting - Horizontal Installations .............................. 23
Venting - Vertical Termination ................................... 24
Gas Line Installation ................................................. 24
Pilot Adjustment ........................................................ 25
High Elevation .......................................................... 25
System Data ............................................................. 25
Gas Pipe Pressure Test ............................................ 25
SIT Valve Description ............................................... 25
Conversion to Propane ............................................. 26
Optional Brick Panels ............................................... 27
Log Installation ......................................................... 27
Flush Door - Standard .............................................. 28
Flush Trim (optional) ................................................. 28
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Page
Louvers - Flush ........................................................ 29
Double Screen Door ................................................. 29
Bay Front (optional) .................................................. 29
Bay Trim (optional) ................................................... 29
Louvers - Bay ........................................................... 30
Full Screen Front ...................................................... 31
Remote Control (optional) ........................................ 33
Wall Thermostat (optional) ....................................... 33
Remote Wall Switch (optional) ................................. 33
Wiring Diagram ......................................................... 34
Fan Installation (optional) ......................................... 35
Operating Instructions
Lighting Plate Instructions ........................................ 36
Operating Instructions .............................................. 37
Lighting Procedure ................................................... 37
Shutdown Procedure ................................................ 37
First Fire ................................................................... 37
Aeration Adjustment ................................................. 37
Normal Operating Sounds of
Gas Appliances .................................................. 38
Maintenance
Maintenance Instructions ........................................ 38
General Vent Maintenance ....................................... 38
Gold-Plated or Brass Louvers .................................. 38
Gold Plated or Brass Trim ........................................ 38
Log Replacement ..................................................... 38
Thermopile/Thermocouple ....................................... 39
Glass Gasket ............................................................ 39
Door Glass: Flush and Bay Glass ............................ 39
Removing Valve........................................................ 40
Installing Valve.......................................................... 40
Parts List
Replacement/Spare Parts List .................................. 41
Warranty
Warranty ................................................................... 47
SAFETY LABEL
This is a copy of the label that accompanies each
P33-3 Zero Clearance Direct Vent Gas Fireplace.
We have printed a copy of the contents here for
your review. The safety label is located on the
front inside base of the unit, visible when the
bottom louver is open.
NOTE: Regency units are constantly being
improved. Check the label on the unit and if
there is a difference, the label on the unit is the
correct one.
For the State of Massachusetts, installation
and repair must be done by a plumber or
gasfitter licensed in the Commonwealth of
Massachusetts.
For the State of Massachusetts, flexible
connectors shall not exceed 36 inches in
length.
For the State of Massachusetts, the appliances individual manual shut-off must be a
t-handle type valve.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
IMPORTANT:
SAVE THESE
INSTRUCTIONS
The P33-NG3 or P33-LP3 Direct Vent Fireplace
must be installed in accordance with these instructions. Carefully read all the instructions in
this manual first. Consult the "authority having
jurisdiction" to determine the need for a permit
prior to starting the installation. It is the responsibility of the installer to ensure this fireplace
is installed in compliance with manufacturer's
instructions and all applicable codes.
BEFORE YOU START
Safe installation and operation of this appliance requires common sense, however, we
are required by the Canadian Safety Standards
and ANSI Standards to make you aware of the
INSTALLATION AND REPAIR
SHOULD BE DONE BY A QUALIFIED SERVICE PERSON. THE
APPLIANCE SHOULD BE INSPECTED BEFORE USE AND AT
LEAST ANNUALLY BY A PROFESSIONAL SERVICE PERSON. MORE
FREQUENT CLEANING MAY
BE REQUIRED DUE TO EXCESSIVE LINT FROM CARPETING,
BEDDING MATERIAL, ETC. IT IS
IMPERATIVE THAT CONTROL
COMPARTMENTS, BURNERS
AND CIRCULATING AIR PASSAGEWAYS OF THE APPLIANCE
BE KEPT CLEAN.
DUE TO HIGH TEMPERATURES,
THE APPLIANCE SHOULD BE
LOCATED OUT OF TRAFFIC AND
AWAY FROM FURNITURE AND
DRAPERIES.
WARNING: FAILURE TO INSTALL
THIS APPLIANCE CORRECTLY
WILL VOID YOUR WARRANTY
AND MAY CAUSE A SERIOUS
HOUSE FIRE.
CHILDREN AND ADULTS SHOULD
BE ALERTED TO THE HAZARDS
OF HIGH SURFACE TEMPERATURES, ESPECIALLY THE FIREPLACE GLASS, AND SHOULD
STAY AWAY TO AVOID BURNS OR
CLOTHING IGNITION.
YOUNG CHILDREN SHOULD BE
CAREFULLY SUPERVISED WHEN
THEY ARE IN THE SAME ROOM
AS THE APPLIANCE.
CLOTHING OR OTHER FLAMMABLE MATERIAL SHOULD NOT
BE PLACED ON OR NEAR THE
APPLIANCE.
GENERAL SAFETY
INFORMATION
10) Be aware of electrical wiring locations in
walls and ceilings when cutting holes for
termination.
11) Under no circumstances should this appliance be modified. Parts that have to be
removed for servicing should be replaced
prior to operating this appliance.
12) Installation and any repairs to this appliance
should be done by a qualified service person. A professional service person should
be called to inspect this appliance annually.
Make it a practice to have all of your gas
appliances checked annually.
1) The appliance installation must conform with
local codes or, in the absence of local codes,
with the current Canadian or National
Gas Codes, CAN1-B149 or ANSI Z223.1
Installation Codes.
13) Do not slam shut or strike the glass door.
2) The appliance when installed, must be
electrically grounded in accordance with
local codes, or in the absence of local codes
with the current National Electrical Code,
ANSI/NFPA 70 or CSA C22.1 Canadian
Electrical Code.
15) The appliance area must be kept clear and
free of combustible materials, (gases and
other flammable vapours and liquids).
3) See general construction and assembly
instructions. The appliance and vent should
be enclosed.
4) This appliance must be connected to the
specified vent and termination cap to the
outside of the building envelope. Never vent
to another room or inside a building. Make
sure that the vent is fitted as per Venting
instructions.
5) Inspect the venting system annually for
blockage and any signs of deterioration.
6) Venting terminals shall not be recessed into a
wall or siding.
7) Any safety glass removed for servicing
must be replaced prior to operating the
appliance.
8) To prevent injury, do not allow anyone who
is unfamiliar with the operation to use the
fireplace.
9) Wear gloves and safety glasses for protection while doing required maintenance.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
14) Under no circumstances should any solid
fuels (wood, paper, cardboard, coal, etc.)
be used in this appliance.
Emissions from burning wood or gas could
contain chemicals known to the State of California to cause cancer, birth defects or other
reproductive harm.
MANUFACTURED
MOBILE HOME
ADDITIONAL
REQUIREMENTS
1) Ensure that structural members are not cut
or weakened during installation.
2) Ensure proper grounding using the #8
ground lug provided. See page 34.
INSTALLATION
INSTALLATION
CHECKLIST
UNIT DIMENSIONS
1) Locate appliance
a) Room location, page 6
b) Clearances to Combustibles, page 7
c) Mantle Clearances, page 7
d) Framing & Finishing Requirements,
page 8
e) Venting Requirements, pages 10 to
15.
4) The P33-3 can be installed in a recessed
position or framed out into the room as in
A, B, C, D. See Diagram 1.
5) This appliance is Listed for bedroom installations when used with a Listed Millivolt
Thermostat. Some areas may have further
requirements, check local codes before
installation.
6) The P33-3 Direct Vent Gas Fireplace is approved for alcove installations, which meet
the clearances listed on this page.
2) Assemble Top Facing Support and Side
Nailing Strips, page 9. (NOTE: must be
done before installing unit into fireplace.)
7) We recommend that you plan your installation on paper using exact measurements
for clearances and floor protection before
actually installing this appliance. Have a
qualified inspector, dealer, or installer review
your plans before installation.
3) Install vent, pages 10 to 24.
4) Make gas and electrical connections. Test
the pilot. Must be as per diagram. Page 25.
Convert to Propane if desired, page 26.
Note: For vent terminations see page 10.
5) Install brick panels (optional), page 27.
6) Install logs and embers and rockwool where
indicated on page 27.
7) Install Flush Door Front (Standard) and
optional Flush Gold Trim, page 28.
8) Install optional Double Screen Door, page
29.
9) Install Optional Bay Front and optional Bay
Gold Trim, page 29.
Diagram 1
10) Install Louvers (Flush or Bay), pages 28
and 29.
A)
B)
C)
11) Install optional Wall Switch, Remote Control,
or Wall Thermostat, page 33.
Flat on Wall
Flat on Wall Corner
Recessed into Wall/Alcove
11) Install Optional Fan, page 35.
13) Final check.
Before leaving this unit with the customer, the
installer must ensure that the appliance is firing correctly and operation fully explained
to customer.
This includes:
1) Clocking the appliance to ensure the correct
firing rate (rate noted on label) after burning
appliance for 15 minutes.
2) If required, adjusting the primary air to ensure
that the flame does not carbon. First allow
the unit to burn for 15-20 min. to stabilize.
CAUTION: Any alteration to the product that
causes sooting or carboning that results
in damage is not the responsibility of the
manufacturer.
LOCATING YOUR
GAS STOVE
1) When selecting a location for your stove,
ensure that the clearances outlined on this
page are met.
2) Provide adequate clearances for servicing.
3) The appliance must be installed on a flat,
solid, continuous surface (e.g. wood, metal,
concrete). This may be the floor, or raised up
on a platform to enhance its visual impact.
If the appliance is going to be installed on
carpeting, combustible linoleum tile or other
combustible material other than wood flooring, the appliance must be installed on a
metal or wood panel extending the full width
and depth of the appliance.
DUCT SYSTEM
OPTION
KIT #946-556
The HeatWave Air Duct Kit increases the effectiveness of your fireplace by dispersing warm
air from the fireplace to remote locations in the
same room or other rooms in your home.
Up to two kits may be installed on the fireplace.
Please Note: Only 1 HeatWave kit may be
operated at one time. This includes the internal
blower option as well.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
CLEARANCES
COMBUSTIBLE MANTELS
The clearances listed below are Minimum distances unless otherwise stated:
Because of the extreme heat this fireplace emits, the mantel clearances are critical. Combustible mantel clearances from top of unit are shown in the diagram below.
A major cause of chimney related fires is
failure to maintain required clearances (air
space) to combustible materials. It is of the
greatest importance that this fireplace and
vent system be installed only in accordance
with these instructions.
Note: A non-combustible mantel may be installed at a lower height if the framing is made
of metal studs covered with a non-combustible board.
Clearance to Combustibles from:
Back
0"
(0mm)
Side
0"
(0mm)
Floor
0"
(0mm)
NOTE: The minimum floor clearance must be
maintained from the top surface of the carpeting, tile, etc.
Minimum Clearance from Top of Unit to:
Mantel*
min. 7" (177mm)
Ceiling
30"
(762mm)
from top of unit.
Side Wall Clearance
Bay or Flush Front
7-1/2" (191mm)
Minimum Vent Clearances:
2-1/2" (64mm) Horizontal Top
1-1/2" (38mm) Horizontal Side
1-1/2" (38mm) Horizontal Bottom
1-1/4" (32mm) Vertical Vent Clearance (Simpson)
1-1/2" (38mm) Vertical Vent Clearance (Flex)
Alcove Clearances:
Max. Depth
36"
Min. Width
48"
Min. Height
59"
(914mm)
(1219mm)
(1499mm)
* see mantel clearance instructions.
This drawing is to scale at 1:6 (one inch = 6 inches). Mantel can be installed anywhere in shaded
area or higher using the above scale.
Note: Ensure the paint that is used on the mantel and the facing is "heat resistant" or the
paint may discolour.
WARNING
Fire hazard is an extreme risk if these
clearances are not adhered to.
MANTEL LEG CLEARANCES
Combustible mantel leg clearances as per diagram below:
Maximum
1-1/2" projection at 2"
minimum clearance.
Clearances for Bay or Flush Front
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
The HeatWave Duct Kit has different clearance and framing requirements, check the
HeatWave manual for details.
INSTALLATION
FRAMING AND FINISHING
Rear Termination
Simpson Dura-Vent
Minimum Clearances
Simpson Dura-Vent Piping
Top Header
10" (254mm)
dia. Hole through
wall for Dura-Vent
1/2"
(13mm)
Drywall
Install Side Nailing Strips, and Top Facing
Support before unit is slipped into position.
See page 9 for assembly details.
1-1/2"
(38mm)
Flex Piping
30”
(762mm)
1) Determine the total thickness of facing
material (e.g. drywall plus ceramic tiles) to
allow the finished surface to be flush with
the front of the unit. Total facing thickness
can vary from 1/2" (13mm) to 1-1/4" (32mm)
thick.
4"
3"
(102mm)(76mm)
Opening for gas
connection
16-1/2”
(419mm)
Minimum
For Both Simpson & Flex
2) Frame in the enclosure for the unit with
framing material.
Flex Pipe
Minimum Clearances
Vertical Termination or
Vertical Rise with Horizontal
Termination
Top Header
1/2"
(13mm)
Drywall
NOTE: If this is an outside corner, the minimum
distance between the vent and the outside corner
is 6" (15cm) with AstroCap termination cap or 12"
(30cm) with Dura-Vent termination cap.
3) For exterior walls, insulate the enclosure to
the same degree as the rest of the house,
apply vapour barrier and drywall, as per local installation codes. (Do not insulate the
fireplace itself.)
4) The top of the unit must not be closer than
30" (762mm) to the ceiling.
5) Combustible material may be brought up to
the top and sides of the unit and be covered
with ceramic tiles, bricks, rock or other suitable combustible finishing materials.
NOTE: If this is an outside corner, the
minimum distance between the vent and the
outside corner is 6" (15cm) with AstroCap
termination cap or 12" (30cm) with Dura-Vent
termination cap.
Note: The unit does not have to be completely enclosed in a chase. The clearance
on top of the unit is 0" to the standoffs
so combustible building materials can
be laid directly on top of the standoffs.
You must maintain clearance from the
vent to combustible materials for flex
for Simpson Dura-Vent, see page 7.
10" (254mm)
dia. Hole through
wall for Flex
1-1/2"
(38mm)
4"
3"
(102mm)(76mm)
Opening for gas
connection
26”
(660mm)
For Both Simpson & Flex
12-3/4”
(324mm)
Minimum
6) Use steel studs for framing where the
1-1/2" (38mm) clearance from the vent
to combustible material cannot be maintained.
The HeatWave Duct Kit has different clearance and framing requirements, check the
HeatWave manual for details.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
UNIT ASSEMBLY
PRIOR TO INSTALLATION
The Top Facing Support, the Side Nailing Strips
and the 2 Top Standoffs must be correctly positioned and attached to the top before the unit
is put into position.
Top Standoff Assembly
The top standoffs are shipped in a flat position
and must be pulled up and bent into the correct shape.
1) Remove the standoffs from on top of the
firebox by undoing the screws.
2) Take each standoff and bend into the correct shape. Bend up at the bend lines until
the screw holes in the standoff and the
pre-punched screw holes on the firebox top
line-up.
3) Attach the standoffs securely to the top with
4 screws per standoff.
Note: Secure the standoffs to the holes
closest to the edge of the firebox top.
Top Facing Support &
Side Nailing Strips
Determine the total thickness of facing material (e.g. drywall plus ceramic tiles) to allow the
finished surface to be flush with the front of the
unit. Total facing thickness can vary from 1/2"
(13mm) to 1-1/4" (32mm) thick.
The Top Facing Support & Side Nailing Strips
can be mounted in various positions depending
on the thickness of the facing material.
1) Mount Top Facing Support using the 3
supplied screws into the three pre-punched
screw holes on the top front of the unit. Adjust
support to desired facing material depth.
2) Mount Side Nailing Strip using the 3 supplied screws into the three pre-punched
screw holes at the front sides of the unit.
Adjust support to desired facing material
thickness.
For a facing material depth of
1-1/4"(32mm), the top facing
support must be reversed.
VENTING INTRODUCTION
The P33-3 uses the "balanced flue" technology Co Axial system. The inner liner vents products of combustion to the outside while the outer
liner draws outside combustion air into the combustion chamber thereby eliminating the need to use heated room air for combustion and losing
warm room air up the chimney.
There are 2 vent systems approved for use with the P33-3: the Regency Direct Vent System (Flex) for Horizontal Terminations only (see pages
11-12), and the Simpson Dura-Vent Systems for Horizontal and Vertical Terminations (see pages 13-24).
Note: These flue pipes must not be connected to any other appliance.
The gas appliance and vent system must be vented directly to the outside of the building, and never be attached to a chimney serving a separate solid
fuel or gas burning appliance. Each direct vent gas appliance must use it's own separate vent system. Common vent systems are prohibited.
NOTE: Ensure compliance with the outside vent terminal location before cutting hole as both dimensions must be met.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
V
E
V
M
V
B
Vent terminal
.
F
V
V
A
G
B
C
V
A
V
B
B
V
A
K
B
H
j
N
V
Area where terminal is not permited
A
V
18"
L
A
Note:
- A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.
- Only permitted if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor.
- If the vent termination is accessible, a certified guard shall be installed.
* As specified in CGA B149 Installation Code. Note: Local codes or regulations may require different clearances.
# In accordance with the current ANSI Z223.1/NFPA 54, Natioinal Fuel Gas Code.
H= Not to be installed above a meter/regulator assembly within (3'/90cm) horizontally
from the centerline of the regulator.
J= Clearance to service regulator vent outlet *(min. 36"/90cm)
K= Clearance to non-mechanical air supply inlet to building or the combustion air inlet to
any other appliance *(12"/30cm) #(9"/23cm)
L= Clearance to a mechanical air supply inlet *(min. 72"/1.8m)
#3' (91cm) above if within 10' (3m) horizontally.
M= Clearance above paved sidewalk or a paved driveway located on public property
*(min. 84"/2.1m)
N= Clearance under veranda, porch, deck, or balcony *(min. 12"/30cm)
V
Fixed Closed
B
24"
Vertical
Termination
Openable
Air supply outlet
Openable
Fixed
Closed
Inside
corner detail
Clearance above grade, veranda, porch, deck, or balcony *(min. 12"/30cm)
Clearance to window or door that may be opened *(12"/30cm) #(9"/23cm)
Clearance to permanently closed window *(min. 12"/30cm)
Vertical clearance to ventilated soffit located above the terminal within a horizontal
distance of (24"/60cm) from the centerline of the terminal (min. 18"/46cm) check with
local code.
E= Clearance to unventilated soffit (min. 15"/38cm)
F= Clearance to outside corner: with AstroCap Termination Cap (min. 6"/15cm), with
Dura-Vent Termination Cap (12"/30cm)
G= Clearance to inside corner: with AstroCap Termination Cap (min. 6"/15cm), with DuraVent Termination Cap (12"/30cm)
A=
B=
C=
D=
D
24"
Vertical
Termination
INSTALLATION
EXTERIOR VENT TERMINATION LOCATIONS
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
REGENCY DIRECT VENT SYSTEM (FLEX)
HORIZONTAL TERMINATIONS ONLY
This venting system, in combination with the P33-3 Direct Vent Gas Fireplace, have been tested and listed as a direct vent heater system by Warnock
Hersey. The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram on page 10.
Regency Direct Vent (Flex) System Termination Kit (Part # 946-513) includes all the parts needed to install the P33-3 with a maximum
run of 2 feet. If installing the P33 with a continuous vent length of more than 2 ft (.6m) to a maximum of 10 ft. (3.0m) using Kit # 946-515 (4 ft) or
946-516 (10 ft) or see page 13 for alternate venting arrangements.
1)
2)
3)
4)
5)
6)
7)
8)
9)
6-7/8" dia. flexible liner (2 ft. length)
4" dia. flexible liner (2 ft. length)
spring spacers (3)
thimble (2)
AstroCap termination cap (1)
screws (12)
tube of Mill Pac (1)
plated screws (8)
screws #8 x 1-1/2" drill point, stainless steel (4)
Wall Thimble (2 pc)
(required in
Canada only)
TM
AstroCap
Termination Cap
(Part# 946-523/P)
4" (102mm)
dia. flue pipe
Notes:
1) Liner sections should be continuous without any
joints or seams.
2) Only Flex pipe purchased from Regency may be
used for Flex installations.
spring
spacer
6-7/8"
(173mm)
dia. Flue pipe
Important
See also
Figure 1 below.
Alternate Horizontal Termination Caps
If using any Cabinet Mantels with Part
# 510956, 510958, 510962, 510964
and 510834 the wall thimble must
be secured first and venting must be
attached to unit before sliding into
final position.
Also Simpson Dura-Vent venting cannot be used with any of the mantels
noted above.
Minimum
Simpson Dura-Vent Center-Line
Figure 1
Minimum Flex Kit Center-Line
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Wherever necessary due to
external location of cap, the
AstroCap can be replaced with
the FPI Riser Vent Termination
Cap or the Dura-Vent Snorkel
Termination Cap.
INSTALLATION
INSTALLATION PROCEDURES
for Regency Direct Vent System (Flex)
1) Locate the unit in the framing, rough in the
gas (preferably on the right side of the unit)
and the electrical (Junction block is on the
left side) on the left. Locate the centerline of
the termination and mark wall accordingly.
Cut a 10"(254mm) hole in the wall (inside
dimension).
*If this is an outside corner, the minimum distance between the vent and the outside
corner is 6" (15cm) with AstroCap termination cap or 12" (30cm) with Dura-Vent
termination cap. See "F" on the diagram on page 10.
Note: To make the installation more aesthetically pleasing, we recommend
framing out a square to mount the
terminal to.
Note: A 2-1/2" (64mm) horizontal top and
1-1/2" (38mm) horizontal sides &
bottom clearance around the liner
must be maintained except that only
a 1" (25mm) clearance is needed at
the termination end. We recommend
framing a 10"(254mm) x 10"(254mm)
(inside dimensions) hole to give
structural rigidity for mounting the
termination.
Note: If installing termination on a siding
covered wall, furring strips must be
used to ensure that the termination
is not recessed into the siding.
2) Level the fireplace and fasten it to the framing using nails or screws through the nailing
strips.
Minimum and Maximum Vent Clearances
5) Slip the assembled liner and termination
assembly through the thimble making sure
the termination cap faces up (there are
markings on the cap that show which way
is up). This will position the termination cap
with proper down slope for draining water.
Fasten the cap to the outer wall with the 4
supplied screws.
6) Pull the centre 4"(100mm) liner and outer
6-7/8"(175mm) liner out enough to slip over
the flue collars of the fireplace.
7) Apply Mill Pac over the fireplace inner collar
and slip the 4"(100mm) liner down over it
and attach with 3 supplied screws.
9) Apply a bead of silicone between the thimble
and termination and around the outer edge
of the terminal at the wall in order to keep
the water out.
IMPORTANT: Do not locate termination
hood where excessive snow or ice
buildup may occur. Be sure to check
vent termination area after snow falls,
and clear to prevent accidental blockage of venting system. When using
snow blowers, make sure snow is
not directed towards vent termination
area.
8) Do the same with the 6-7/8"(175mm) liner.
3) Assemble the vent assembly by applying
Mill Pac to the 4"(100mm) inner collar of the
termination and slipping the 4"(100mm) liner
over it at least 1-3/8" (35mm). Fasten with
the 3 screws (drilling pilot holes will make this
easier). Apply Mill Pac or high temperature
silicone to the 6-7/8"(175mm) flex pipe and
slip it over the 6-7/8" outer collar of the vent
terminal at least 1-3/8"(35mm) and fasten
with the 3 screws.
4) Separate the 2 halves of the wall thimble and
securely fasten the one with the tabs to the
outside wall making sure that the tabs are
on top and bottom. Fasten the other thimble
half to the inside wall. The thimble halves
slip inside each other and can be adjusted
for 2 x 4 or 2 x 6 walls. The liners must slip
over the collars a minimum of 1-3/8".
4" (102mm)
dia. flue pipe
with spring spacer
2” x 4” or 2” x 6”
(21mm x 102mm
or 21mm x 152mm)
Termination Cap
Screws
(3 per
connection)
6-7/8"
(175mm)
dia. air intake
Screws
(4 per connection)
Wall Thimble 2 pieces
(10" (254mm) Outer Diameter)
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
RIGID PIPE VENTING SYSTEMS
Horizontal or Vertical Terminations
The minimum components required for a basic
horizontal termination are:
1
1
1
1
1
AstroCap Horizontal Termination Cap
45o Elbow
Rigid Pipe Adaptor
Wall Thimble
Length of pipe to suit wall thickness
(see chart)
For siding other than vinyl furring strips may be
used, instead of the vinyl siding standoff, to create
a level surface to mount the vent terminal. The
Terminal must not be recessed into siding.
Vertical
Terminal
Storm Collar
Vinyl Siding
Standoff (Optional)
Flashing
Horizontal
Termination
Cap
Ceiling Firestop
If a Vinyl Siding Standoff is required (it must be
used with vinyl siding), measure to outside surface
of wall without siding and add 2 inches.
Alternate Horizontal Termination Caps
Wall Thimble
Pipe Length
Adj.Pipe Length
11" - 14-5/8"
(279mm - 372mm)
90o Elbow
24" (610mm)
Pipe Length
Horizontal
Termination Cap
Vinyl Siding
Standoff (Optional)
Wall Thimble
o
45 Elbow
Adj.Pipe Length
11" - 14-5/8"
(279mm - 372mm)
Rigid Pipe Adaptor
WARNING:
Do not combine venting components from
different venting systems.
However use of the the AstroCapTM and FPI
Riser is acceptable with all systems.
Flat Wall Installation
Max. Wall
Vent Length
Thickness (inches)
Required (inches)
7-1/4"
6"
10-1/4"
9"
13-1/4"
12"
12-1/4" - 15-7/8"
11" - 14-5/8" Adj. Pipe
18-1/4" - 25-1/4"
11" - 14-5/8" Adj. Pipe
This product has been evaluated by Intertek for
using a Dura-Vent Flue Adaptor in conjunction
with Selkirk Direct-Temp and Ameri Vent Direct
venting systems. Use of these systems with the
Direct Vent GS starting collar is deemed acceptable and does not affect the Intertek WHI listing
of components.
When using piping other than Simpson
Dura-Vent, 3 screws must be used to
secure rigid pipe to adaptor.
The FPI AstroCapTM and FPI Riser Vent terminal is certified for installations using FPI venting systems as well as Simpson Dura-Vent®, Direct Vent GS,
American Metal Products, Ameri Vent Direct vent and Selkirk Direct-Temp. FPITM, and FPI AstroCapTM are the proprietary trademarks of FPI Fireplace
Products International Ltd. Dura-Vent® and Direct Vent GS are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
RIGID PIPE VENTING COMPONENTS LIST
All Simpson Dura-Vent components are available directly from FPI.
Description
Simpson Dura-Vent
Direct VentGSR
Selkirk
Direct-TempTM
AmeriventR
Direct Vent
6" Pipe Length, Galvanized
6" Pipe Length, Black
7" Pipe Length, Galvanized
7" Pipe Length, Black
9" Pipe Length, Galvanized
9" Pipe Length, Black
12" Pipe Length, Galvanized
12" Pipe Length, Black
18" Pipe Length, Galvanized
18" Pipe Length, Black
24" Pipe Length, Galvanized
24" Pipe Length, Black
36" Pipe Length, Galvanized
36" Pipe Length, Black
48" Pipe Length, Galvanized
48" Pipe Length, Black
908
908B
N/A
N/A
907
907B
906
906B
N/A
N/A
904
904B
903
903B
902
902B
4DT-6
4DT-6B
N/A
N/A
4DT-9
4DT-9B
4DT-12
4DT-12B
4DT-18
4DT-18B
4DT-24
4DT-24B
4DT-36
4DT-36B
4DT-48
4DT-48B
N/A
N/A
4D7
4D7B
N/A
N/A
4D12
4D12B
N/A
N/A
4D2
4D2B
4D3
4D3B
4D4
4D4B
Adjustable Length, 11"-14", Galv.
Adjustable Length, 11"-14", Black
Adjustable Length, 17"-24", Black
Adjustable Length, 7" Galvinized
Adjustable Length, 7" Black
Adjustable Length, 12" Galvinized
Adjustable Length, 12" Black
911
911B
917B
N/A
N/A
N/A
N/A
4DT-AJ
4DT-AJB
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
4D7A
4D7AB
4D12A
4D12AB
45O Elbow, Galvinized
45O Elbow, Black
45O Elbow, Swivel, Galvinized
45O Elbow, Swivel, Black
90O Elbow, Galvinized
90O Elbow, Black
90O Elbow, Swivel, Galvinized
90O Elbow, Swivel, Black
945
945B
945G
945BG
990
990B
990G
990BG
4DT-EL45
4DT-EL45B
N/A
N/A
4DT-EL90S
4DT-EL90SB
N/A
N/A
4D45L
4D45LB
N/A
N/A
4D90LS
4D90LBS
N/A
N/A
Ceiling Support
Cathedral Support Box
Wall Support/Band
Offset Support
Wall Thimble, Black
Wall Thimble Support Box/Ceiling Support
Firestop Spacer
Trim Plate, Black
Brass Trim for Wall Thimble/Ceiling Support
949 - n/a from FPI
941
988
989 - n/a from FPI
942
940
963
N/A
3951
4DT-CS
4DT-CSS
4DT-WS/B
4DT-OS
4DT-WT
N/A
4DT-FS
4DT-TP
N/A
4DFSP
4DRSB
4DWS
N/A
4DWT
N/A
4DFSP
4DFPB
N/A
Attic Insulation Shield 12"
Attic Insulation Shield - Cold Climates 36"
N/A
N/A
N/A
N/A
4DAIS12
4DAIS36
Basic Horizontal Termination Kit (A)
Horizontal Termination Kit (B)
Vertical Termination Kit
970
971
978
4DT-HKA
4DT-HKB
4DT-VKC
4DHTK2
4DHTK1
4DVTK
High Wind Vertical Cap
High Wind Horizontal Cap
Horizontal Square Termination Cap
Verical Termination Cap
Storm Collar
991
985
984
980
953
N/A
N/A
4DT-HHC
4DT-HVC
4DT-SC
N/A
N/A
4DHC
4DVC
4DSC
Adjustable Flashing, 0/12-6/12
Adjustable Flashing, 6/12-12/12
943
943S
4DT-AF6
4DT-AF12
4DF
4DF12
Vinyl Siding Standoff
Vinyl Siding Shield Plate
950
N/A
4DT-VS
4DT-VSP
N/A
N/A
Snorkel Termination 14"
Snorkel Termination 36"
982
981
4DT-ST14
4DT-ST36
4D12S
4D36S
946-506/P
640-530/P
510-994
946-205
Vent Guard (Optional)
Riser Vent Terminal
Rigid Pipe Adaptor (must use with all rigid piping)
Vinyl Siding Shield for Riser Vent Terminal
946-208/P
946-523/P
946-206
Vent Guard (Optional) - Riser Vent Terminal
AstroCap Horizontal Cap
Vinyl Siding Standoff - AstroCap
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
RIGID PIPE VENTING ARRANGEMENTS - VERTICAL TERMINATIONS
(Propane & Natural Gas)
The shaded area in the diagram shows all allowable combinations of straight vertical and offset to vertical terminations , using one 90o elbow, with
rigid pipe vent systems for Propane and Natural Gas.
•
•
•
Vent must be supported at offsets.
Firestops are required at each floor level and whenever passing through a wall.
Maintain clearances to combustibles.
Note: Must use optional rigid pipe adapter when using rigid pipevent systems (Part # 510-994).
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
The P33-3 is approved for a maximum 40 ft. straight vertical, with rigid pipe
vent systems for Propane and Natural Gas.
The shaded area in the diagram shows all allowable combinations of straight
vertical and offset to vertical terminations with rigid pipe vent systems for
Propane and Natural Gas. Maximum two 45o elbows allowed.
•
•
•
Vent must be supported at offsets.
Firestops are required at each floor level and whenever passing
through a wall.
Maintain clearances to combustibles.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
RIGID PIPE VENTING ARRANGEMENTS - HORIZONTAL TERMINATIONS
REGENCY DIRECT VENT SYSTEM (FLEX)
(Propane & Natural Gas)
This diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 45o and one 90o elbow (two 45o elbows equal
one 90o elbow).
Note: Must use optional rigid pipe adaptor (Part # 510-994) when using rigid pipe vent systems. (Refer to page 13.)
A vent guard should be used whenever
the termination is lower than the specified
minimum or as per local codes.
Note: Regency Direct Vent System (Flex) is
only approved for horizontal terminations.
•
•
•
Maintain clearances to combustibles.
Horizontal vent must be supported every 3 feet.
Firestops are required at each floor level and whenever passing through a wall.
Minimum
Simpson Dura-Vent Center-Line
Minimum Flex Kit Center-Line
Important
If using any Cabinet Mantels with Part
# 510956, 510958, 510962, 510964
and 510834 the wall thimble must
be secured first and venting must be
attached to unit before sliding into
final position.
Also Simpson Dura-Vent venting cannot be used with any of the mantels
noted above.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
Horizontal Venting with Two (2) 90o Elbows
Horizontal Venting with Three (3) 90o Elbows
One 90o elbow = Two 45o elbows.
One 90o elbow = Two 45o elbows.
Option
A)
B)
C)
D)
E)
F)
1'
2'
3'
4'
5'
6'
V
Min.
Min.
Min.
Min.
Min.
Min.
H + H1
3' Max.
4' Max.
5' Max.
6' Max.
7' Max.
8' Max.
With these options, maximum total pipe length is 30
feet with minimum of 6 feet
total vertical and maximum
8 feet total horizontal.
Please note minimum 1
foot between 90o elbows
is required.
Option
A)
B)
C)
D)
E)
F)
H
1 Max.
2' Max.
3' Max.
4' Max.
5' Max.
6' Max.
V
1' Min.
3' Min.
5' Min.
7' Min.
9' Min.
11' Min.
H + H1 + H2 With these options, max.
3' Max.
total pipe length is 30 feet
with min. of 11 feet total
5' Max.
vertical and max. 9 feet
6' Max.
total horizontal.
7' Max.
Please note min.
8' Max.
1 foot between 90o
elbows is required.
9' Max.
Horizontal Venting with Two (2) 90o Elbows
One 90o elbow = Two 45o elbows.
Option
A)
B)
C)
D)
E)
H
1' Max.
2' Max.
3' Max.
4' Max.
5' Max.
V
1' Min.
2' Min.
4' Min.
6' Min.
8' Min.
H + H1
3' Max.
5' Max.
6' Max.
7' Max.
8' Max.
With these options, max.
total pipe length is 30 feet
with min. of 8 feet total
vertical and max. 8 feet
total horizontal.
Please note min. 1 foot
between 90o elbows is
required.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
Horizontal Venting with Three (3) 90o Elbows
o
One 90 elbow = Two 45o elbows.
Option
A)
B)
C)
D)
E)
F)
V
2' Min.
3' Min.
4' Min.
5' Min.
6' Min.
7' Min.
H
1' Max.
2' Max.
3' Max.
4' Max.
5 Max.
6' Max.
V + V1
3' Min.
4' Min.
6' Min.
8' Min.
10' Min.
12' Min.
H + H1
4' Max.
5' Max.
6' Max.
7' Max.
8' Max.
With these options,
max. total pipe length
is 30 feet with min. of
12 feet total vertical
and max. 9 feet total
horizontal.
Please note min. 1
foot
between 90o
9'
Max.
elbows is required.
Vertical Venting with Two (2) 90o Elbows
Vertical Venting with Two (2) 90o Elbows
One 90o elbow = Two 45o elbows.
Option
A)
B)
C)
D)
E)
V
1' Min.
2' Min.
3' Min.
4' Min.
5' Min.
H
4' Max.
5' Max.
6' Max.
7' Max.
8' Max.
V + V1
2' Min.
3' Min.
4' Min.
5' Min.
6' Min.
One 90o elbow = Two 45o elbows.
With these options, max. total
pipe length is 30 feet with min.
of 6 feet total vertical and max.
8 feet total horizontal.
Please note min. 1 foot
between 90o elbows is required.
Option
A)
B)
C)
D)
E)
H + H1
2' Max.
3' Max.
4' Max.
5' Max.
6' Max.
For additional vertical venting with 2
x 90o elbows, refer to page 15.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
V
2' Min.
3' Min.
4' Min.
5' Min.
6' Min.
With these options, max. total
pipe length is 30 feet with min.
of 6 feet total vertical and max.
6 feet total horizontal.
Please note min. 1 foot
between 90 o elbows is
required.
INSTALLATION
Vertical Venting with Three (3) 90o Elbows
One 90o elbow = Two 45o elbows.
Option
A)
B)
C)
D)
E)
H
1' Max.
2' Max.
3' Max.
4' Max.
5' Max.
V
1' Min.
2' Min.
3' Min.'
4' Min.
5' Min.
H + H1
3' Max.
4' Max.
5' Max.
6' Max.
7' Max.
V + V1
3' Min.
5' Min.
7' Min.
9' Min.
11' Min.
With these options, max. total
pipe length is 30 feet with min.
of 11 feet total vertical and
max. 7 feet total horizontal.
Please note min. 1 foot
between 90 o elbows is
required.
Vertical Venting with Three (3) 90o Elbows
One 90o elbow = Two 45o elbows.
Option
A)
B)
C)
D)
E)
F)
V
2' Min.
3' Min.
4' Min.
5' Min.
6' Min.
7' Min.
H + H1
3' Max.
4' Max.
5' Max.
6' Max.
7' Max.
8' Max.
V + V1 With these options, max.
4' Min. total pipe length is 30 feet
6' Min. with min. of 10 feet total
7' Min. vertical and max. 8 feet total
horizontal.
8' Min. Please note min. 1 foot
9' Min. between 90 o elbows is
10' Min. required.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
VERTICAL TERMINATION
WITH CO-LINEAR FLEX SYSTEM
THE APPLIANCE MUST NOT BE
CONNECTED TO A CHIMNEY FLUE
SERVING A SEPARATE SOLID FUEL
BURNING APPLIANCE.
Masonry chimneys may take various contours which the flexible liner will accommodate. However,
keep the flexible liner as straight as possible, avoid unnecessary bending.
The Air Intake pipe must be attached to the inlet air collar of the termination cap.
This appliance is designed to be attached to
two 3" (76mm) co-linear aluminium flex running
the full length of the chimney. See the Venting
Arrangements on next page for minimum and
maximum heights.
Co-linear DV
Vertical Termination
Cap # 946-529
Required Parts:
Part #
946-529
948-305
946-563
Kit
510-994
A maximum
of two certified
joiner kits
may be used
per length.
#948-305
35 ft (11m)
Description
Co-linear DV Vertical
Termination Cap
3" Flex - 35 ft.
Co-Axial to Co-Linear Adapter
which contains the following:
Co-linear Flex Adapter
Outer Pipe
Inner Pipe Adapter
Rigid Pipe Adaptor
945
45o Elbow
Alternate Approved Caps
980
Vertical Termination Cap
991
High Wind Cap
923GK 3" Co-linear Adapter with flashing
FPI Cabinet and/or Flat Wall Mantles
may be used in these applications ensuring that clearances to combustibles
are maintained.
Flex Liner
Exhaust
Flue
Outer
Pipe
with Kit#
946-563
Air Intake
Pipe Length
Co-Linear
Flex
Adapter
with Kit#
946-563
Rigid Pipe Adaptor
# 510-994
45o Elbow
Inner Pipe
Adapter
with Kit#
946-563
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
Venting Arrangements - Vertical Terminations
with Co-linear Flex System for both
Residential & Manufactured Homes
into Masonry Fireplaces
The shaded area in the diagrams show the
allowable vertical terminations.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
HORIZONTAL INSTALLATIONS
Install the vent system according to the
manufacturer's instructions included with the
components.
b) Horizontal runs of vent must be supported every three feet. Wall straps are
available for this purpose.
1) Set the unit in its desired location. Check
to determine if wall studs or roof rafters
are in the way when the venting system is
attached. If this is the case, you may want
to adjust the location of the unit. Rough in
the gas preferably on the right side of the
unit and the electrical (junction block is on
the left side) on the left.
5) Mark the wall for a 10" x 10" square hole.
The center of the square hole should line
up with the centerline of the horizontal pipe.
Cut and frame the 10 inch square hole in
the exterior wall where the vent will be
terminated. If the wall being penetrated is
constructed of non-combustible material,
i.e. masonry block or concrete, a 7"(178mm)
diameter (7-1/2"(191mm) dia. for flex) hole
is acceptable.
Diagram 2a
2) Direct Vent pipe and fittings are designed
with special twist-lock connections to connect the venting system to the appliance
flue outlet. A twist-lock appliance adaptor
is an available option that must be used in
conjunction with the Simpson Dura-Vent
Direct Vent GS system.
3) Put a bead of silicone inside the outer section of the adapter and a bead of Stove
Mate on the inner collar. Slip the adapter
over the existing inner and outer flue collar
and fasten to the outer collar only with the
3 supplied screws (drilling pilot holes will
make this easier). Level the fireplace and
fasten it to the framing using nails or screws
through the nailing strips.
4) Assemble the desired combination of pipe
and elbows to the appliance adaptor and
twist-lock for a solid connection.
Note:
a) Twist-lock procedure: Four indentations,
located on the female ends of pipes and
fittings, are designed to slide straight
onto the male ends of adjacent pipes
and fittings, by orienting the four pipe
indentations so they match and slide
in to the four entry slots on the male
ends, Dia. 1. Push the pipe sections
completely together, then twist-lock
one section clockwise approximately
one-quarter turn, until the two sections
are fully locked. The female locking lugs
will not be visible from the outside, on
the Black Pipe or fittings. They may be
located by examining the inside of the
female ends.
Note:
a) The horizontal run of vent must be level,
or have a 1/4 inch rise for every 1 foot
of run towards the termination. Never
allow the vent to run downward. This
could cause high temperatures and
may present the possibility of a fire.
b) The location of the horizontal vent termination on an exterior wall must meet all
local and national building codes, and
must not be blocked or obstructed. For
External Vent Terminal Locations, see
diagram on page 9.
c) Snorkel Terminations:
For installations requiring a vertical rise
on the exterior of the building, 14-inch
and 36-inch tall Snorkel Terminations
and the Riser Vent as shown in Dia. 2 &
2a are available. Follow the same installation procedures as used for standard
Horizontal Termination. NEVER install
the snorkel upside down.
Diagram 1
6) The arrow on the vent cap should
be pointing up. Insure that the 1-1/2"
clearances to combustible materials are
maintained (Dia. 3). Install the termination
cap. AstroCapTM or Dura-Vent Horizontal
Termination Cap may be used.
Diagram 3
The four wood screws provided should
be replaced with appropriate fasteners for
stucco, brick, concrete, or other types of
sidings.
Diagram 2
Note: Apply sealant "Mill-Pac" to inner pipe
and high temperature silicone sealant to outer pipe on every twist-lock
joint.
Below Grade Snorkel Installation
If the Snorkel Termination must be
installed below grade, i.e. basement
application, proper drainage must be
provided to prevent water from entering the Snorkel Termination. Refer to
Dura-Vent Installation instructions for
details. Do not attempt to enclose the
Snorkel within the wall, or any other type
of enclosure.
*As specified in CGA B149 Installation Code.
Local codes or regulations may require different clearances.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Note: If installing termination on a siding
covered wall, a vinyl siding standoff or
furring strips must be used to ensure
that the termination is not recessed
into the siding.
7) Before connecting the horizontal run of vent
pipe to the vent termination, slide the Wall
Thimble (Part # 620-926) over the vent
pipe.
8) Slide the appliance and vent assembly towards the wall carefully inserting the vent
INSTALLATION
pipe into the vent cap assembly. It is
important that the vent pipe extends into
the vent cap sufficient distance so as to
result in a minimum pipe overlap of 1-1/4
inches. Secure the connection between the
vent pipe and the vent cap 3 sheet metal
screws.
4) Assemble the desired lengths of pipe and
elbows. Ensure that all pipes and elbow
connections are in the fully twist-locked
position and sealed.
Diagram 4
9) Install wall thimble in the center of the
10" square and attach with wood screws
(Diagram 4).
Roof Pitch
Note: Apply sealant "Mill-Pac" to inner pipe
and high temperature silicone sealant to outer pipe on every twist-lock
joint.
Diagram 4
VERTICAL
TERMINATION
5) Cut a hole in the roof centered on the small
drilled hole placed in the roof in Step 2. The
hole should be of sufficient size to meet
the minimum requirements for clearance
to combustibles of 1-1/2". Slip the flashing
under the shingles (shingles should overlap
half the flashing) as per Diagram 3.
8) Install the vertical termination cap by twistlocking it.
1) Maintain the 1-1/2" clearances (air spaces)
to combustibles when passing through ceilings, walls, roofs, enclosures, attic rafter,
or other nearby combustible surfaces. Do
not pack air spaces with insulation. Check
pages 13-17 for the maximum vertical rise
of the venting system and the
maximum horizontal offset
limitations.
2) Set the gas appliance in its
desired location. Drop a plumb
bob down from the ceiling to
the position of the appliance
flue exit, and mark the location
where the vent will penetrate
the ceiling. Drill a small hole
at this point. Next, drop a
plumb bob from the roof to
the hole previously drilled
in the ceiling, and mark
the spot where the vent
will penetrate the roof.
Diagram 1
3) A Firestop spacer must be installed in the
floor or ceiling of every level. To install the
Firestop spacer in a flat ceiling or wall, cut
a 10 inch square hole. Frame the hole as
shown in Diagram 2 and install the firestop.
flat to 7/12
over 7/12 to 8/12
over 8/12 to 9/12
over 9/12 to 10/12
over 10/12 to 11/12
over 11/12 to 12/12
over 12/12 to 14/12
over 14/12 to 16/12
over 16/12 to 18/12
over 18/12 to 20/12
over 20/12 to 21/12
Minimum Vent Height
Feet
Meters
2
0.61
2
0.61
2
0.61
2.5
0.76
3.25
0.99
4
1.22
5
1.52
6
1.83
7
2.13
7.5
2.29
8
2.44
Note: Any closets or storage spaces, which
the vent passes through must be enclosed.
Diagram 3: The upper half of the flashing is
installed under the roofing material and not
nailed down until the chimney is installed. This
allows for small adjustments.
6) Continue to assemble pipe lengths.
Note: If an offset is necessary in the attic to
avoid obstructions, it is important to
support the vent pipe every 3 feet, to
avoid excessive stress on the elbows,
and possible separation. Wall straps
are available for this purpose.
Galvanized pipe is desirable above the roofline
due to its higher corrosion resistance. Continue
to add pipe sections through the flashing until
the height of the vent cap meets the minimum
height requirements specified in Dia. 4 or local
codes. Note that for steep roof pitches, the
vertical height must be increased. A poor
draft, or down drafting can result from high
wind conditions near big trees or adjoining
roof lines, in these cases, increasing the
vent height may solve the problem.
7) Ensure vent is vertical and secure the base
of the flashing to the roof with roofing rails,
slide storm collar over the pipe section and
seal with a mastic.
GAS LINE
INSTALLATION
The gas line is brought through the right side of
the appliance. The gas valve is situated on the
right hand side of the unit and the gas inlet is
on the right hand side of the valve.
The gas line connection may be made of rigid
pipe, copper pipe or an approved flex connector. (If you are using rigid pipe, ensure that the
valve can be removed for servicing.) Since some
municipalities have additional local codes it is
always best to consult with your local authorities
and the CAN/CGA B149 installation code.
For USA installations follow local codes and/or
the current National Fuel Gas Code, ANSI
Z223.1.
When using copper or flex connectors use only
approved fittings. Always provide a union so
that gas lines can be easily disconnected for
servicing. Flare nuts for copper lines and flex
connectors are usually considered to meet this
requirement.
Important: Always check for gas leaks with a
soap and water solution or gas leak detector.
Do not use open flame for leak testing.
Diagram 2
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
PILOT ADJUSTMENT
Periodically check the pilot flames. Correct
flame pattern has three strong blue flames:
1 flowing around the thermopile, 1 around
the thermocouple and 1 flowing across the
burner (it does not have to be touching the
burner).
Note:
If you have an incorrect flame pattern, contact your Regency dealer for further
instructions.
P33-NG3 System Data
Conversion Kit# 431-969
For 0 to 2000 feet altitude
Burner Inlet Orifice Sizes:
#44
Max. Input Rating 22,500 Btu/h
Min. Input Rating 12,500 Btu/h
For 2000 to 4500 feet altitude
Burner Inlet Orifice Sizes:
#45
Max. Input Rating 21,000 Btu/h
Min. Input Rating 10,500 Btu/h
Supply Pressure
min.5.0" w.c.
Manifold Pressure
(High)
3.8"+/- 0.2" w.c.
P33-LG3 System Data
For 0 to 4500 feet altitude
Burner Inlet Orifice Sizes:
Incorrect flame pattern will have small, probably yellow flames, not coming into proper
contact with the rear burner or thermopile
or thermocouple.
#54
Max. Input Rating
Min. Input Rating
21,500 Btu/h
10,500 Btu/h
Supply Pressure
min.12.0" w.c.
Manifold Pressure
(High)
11"+/- 0.2"w.c.
HIGH ELEVATION
This unit is approved in Canada for altitude
to 4500 ft. (CAN/CGA-2.17-M91). For Natural
Gas installations above 4500 ft. follow current
CAN/CGA-B149.1.
S.I.T. VALVE DESCRIPTION
1)
2)
3)
4)
5)
6)
7)
8)
9)
Gas cock knob
Manual high/low adjustment
Pilot Adjustment
Thermocouple Connection - option
Outlet Pressure Tap
Inlet Pressure Tap
Pilot Outlet
Main Gas Outlet
Alternative TC Connection Point
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
GAS PIPE PRESSURE
TESTING
The appliance must be isolated from the gas
supply piping system by closing its individual
manual shut-off valve during any pressure
testing of the gas supply piping system at
test pressures equal to or less than 1/2 psig.
(3.45 kPa). Disconnect piping from valve at
pressures over 1/2 psig.
The manifold pressure is controlled by a regulator built into the gas control, and should be
checked at the pressure test point.
Note: To properly check gas pressure, both
inlet and manifold pressures should
be checked using the valve pressure
ports on the valve.
1) Make sure the valve is in the "OFF" position.
2) Loosen the "IN" and/or "OUT" pressure
tap(s), turning counterclockwise with a 1/8"
wide flat screwdriver.
3) Attach manometer to "IN" and/or "OUT"
pressure tap(s) using a 5/16" ID hose.
4) Light the pilot and turn the valve to "ON"
position.
5) The pressure check should be carried out
with the unit burning and the setting should
be within the limits specified on the safety
label.
6) When finished reading manometer, turn
off the gas valve, disconnect the hose and
tighten the screw (clockwise) with a 1/8"
flat screwdriver. Note: Screw should be
snug, but do not over tighten.
INSTALLATION
Conversion Kit from Natural Gas to Propane Model #431-969
for P33-3 using SIT 820 NOVA Gas Valve
THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER
IF IN DOUBT DO NOT DO THIS CONVERSION !!
Conversion Kit Contains:
Qty. Part #
Description
1 910-018 SIT Conversion Kit-50%
Turndown LP
1 910-037 LP Injector (Pilot Orifice)
1 904-163 Burner Orifice #54
1 908-255 Decal "Converted to Propane"
1 908-528 Red "PROPANE" label
1 908-529 5/32" Allen Key
1 908-812 Instruction Sheet
7) Unscrew the pilot orifice with the allen key
and replace with the LP pilot orifice in the
kit and replace pilot cap.
1) Shut off the gas supply.
2) Remove the louvers (and bay door if it is
installed).
3) Open the flush door and remove the door.
4) Remove the logs and embers/rockwool.
5) Remove the 2 screws holding the Burner
Assembly to the firebox base. Push the
Burner Assembly to the left and lift out.
8) Remove burner orifice with a 1/2" wrench
and discard. Use another wrench to hold on
to the elbow behind the orifice.
Burner Orifice
Remove the 2 screws, push Burner
Assembly to the left and lift out.
6) Pull off the pilot cap to expose the pilot
orifice.
9) Reinstall new burner orifice LP stamped #54
and tighten.
10) Remove and discard the 3 pressure regulator mounting screws (A), pressure regulator
tower (B) and diaphragm (C).
11) Insure that the rubber gasket (D) is properly
positioned and install the new HI/LO pressure regulator assembly to the valve using
the new screws (E) supplied with the kit.
Tighten screws securely.
14) Replace yellow "Natural Gas" label with red
"Propane" label
12) Reverse steps 5) to 2).
16) Check inlet and outlet pressures.
13) Attach clear label "This unit has been converted to Propane" near or on the serial #
decal. Attach white label "This valve has
been converted from NG to LPG using SIT
conversion Kit Code 0.907.202" onto the
valve.
17) Check operation of flame control.
15) Check for gas leaks.
18) Check for proper flame appearance and
glow on logs.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
OPTIONAL BRICK
PANELS
1) Undo the bottom 2 door latches and open
and remove glass door. Remove logs.
2) Attach the 2 Rear Brick Retaining clips to
the rear wall. Loosen the screws in the top
and rear wall of the firebox and slide the
retaining clips into position (tight against the
firebox top) and then tighten the screws.
LOG SET INSTALLATION
D) 251
A) 250
Read the instructions below carefully
and refer to the diagrams. If logs
are broken do not use the unit until
they are replaced. Broken logs can
interfere with the pilot operation.
Log Kit # 431-930 contains the folThe 3-digit numbers (i.e. 250) are
molded into the rear of each log.
B) 254
C) 253
lowing pieces:
Note: The logs must not be in the unit.
3) Insert the back brick panel by carefully slipping it between the back wall of the firebox
and the rear log bracket.
A)
B)
C)
D)
E)
F)
G)
H)
250
254
253
251
252
Rear Log
Middle Cross Log
Front Left Cross Log
Rear Left Log
Front Right Cross Log
Embers
Vermiculite
Rockwool
902-250
902-254
902-253
902-251
902-252
902-156
902-179/21
902-153
E) 252
4) Place Log 254 on the front right side of the
burner. Push the back of the log against the
2 brackets with the notch on the bottom right
side of the log fitting into the right side of
the grate.
Notch
254
NOTE: If you will be installing the optional
Brick Panels, install the Brick Panels
prior to installing the logs.
1) Carefully remove the logs from the box and
unwrap them. The logs are fragile, handle
with care - do not force into position.
Bracket
Bracket
2) Sprinkle the vermiculite and embers around
the firebox base.
4) Put the side panels in next. Slide them in
from the front and push them flat up against
the wall. Be very careful not to scratch them
on the firebox hardware.
250
254
Vermiculite
Vermiculite
Vermiculite
5) Position Log 253 across the cutouts in Logs
250 and 254 with the notch on the left side
of the log fitting into the 2nd grate tab.
3) Place the Log 250 on the rear log support
pins with the flat side to the back.
Cutouts
253
5) Slide the Top Brick Panel into position and
slide the Top Brick Retaining clips so that
they hold the Top Brick Panel in place and
tighten down the screws.
250
250
254
2nd Grate Tab
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
8) Pull off ember size pieces of rockwool and
gently place them on the front of the burner
tray in the places shown in the photo below. Do
not compress the rockwool, leave it loose.
25
3
250
254
6) Place the bottom left front edge of Log 251
against the left edge of the burner tray and
rest the log on the cutout on Log
253.
Diagram 1
Place rockwool in these 2 locations
on the burner tray.
250
25
3
251
254
9) Test fire to ensure proper light off (make
sure flame flows smoothly from one end of
burner to the other). If there is any flame
hesitation, check that area for any blockage
of the burner ports.
10) Install flush glass and bay glass (if used) as
Diagram 2
Use the hook to pull the spring out until you
can put the hook into the slot on the bottom
door bracket. Repeat for 2nd spring. See
diagram 3.
Cutout
7) Position Log 252 across the cutouts in Logs
254 and 253. The notch in the bottom right
end fitting against the 5th grate tab.
25
The standard flush door comes with a black
frame. To install the frame, simply hook the top
door flange onto the top of the unit and swing
the door towards the unit, diagram 1. Be careful that the glass gasket does not roll up; there
must be a gap between the gasket and the door
lip to ensure that the door sits securely on the
unit. Diagram 2.
2
3
254
25
STANDARD FLUSH
DOOR
Diagram 3
To remove the flush door, reverse the above
steps.
Optional Flush Trim
Attach the round magnets to the back of the top
trim piece and to the bottom trim piece, then attach trim to the top and bottom of Flush door.
5th Grate Tab
250
251
25
3
25
254
2
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
FLUSH LOUVERS
1) Install the top louver by sliding the two
bracket clips into the brackets located underneath the top of the firebox.
2) Install the bottom louver by folding the louver
down and then sliding the Bottom Louver
bracket down onto the 2 pins on the base
of the unit (dia. 1). Secure with 1 screw as
per dia. 2.
Diagram 1
DOUBLE SCREEN
DOOR
1) Pull out the top louver.
2) Center the screen door and hook over the
flush door.
Diagram 2
3) Open the screen door(s) and secure the
screen door to the flush door front with 2
clips on the bottom left and right side.
Note: If any maintenance etc. must be done
in the firebox, first remove the Bay
louvers and door.
Note: Top and
bottom louvers
are different.
Optional Bay Trim
Clip locations
3) Open the bottom louver. Pull the Burner
ON/OFF control box from inside the bottom
of the fireplace and position the slots in the
bracket over the 2 screws on the left side of
the bottom louver. Push down to lock into
place. Tighten the screws.
Clip installed on right side.
OPTIONAL BAY DOOR
The Bay louvers MUST be used
with the Bay glass option.
The optional Bay door is an overlay on the
flush front. The standard flush door and glass
must remain on the unit.
Screws on louver bracket
Burner ON/OFF
control box
1) Hook the top of the bay door over the flush
door flange and swing the bottom against
the bottom flange of the flush door.
2) Secure to the flush door bottom bracket with
2 screws provided.
3) Slide the valve extension knobs onto the
valve knobs.
Burner ON/OFF control box attached to bottom flush louver.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Attach 4 supplied magnets each to the back of
the top and bottom trim pieces, and attach trim
to the top and bottom of Bay door.
INSTALLATION
BAY LOUVERS
1) Remove flush louver top heat shield by removing the 4 screws.
4) Install bottom louver by sliding the two bracket clips into the brackets
located underneath the bay door. Secure with 1 screw into each
Bottom Louver Mounting Bracket as per diagram below. Use the
bottom hole in the bracket.
5) Slide the valve extension knobs onto the valve knobs. Match the
correct ext. knob with the valve knob.
Flush Louver Top
Heat Shield
2) Install the bay louver top heat shield and secure with 4 screws.
6) Open the bottom louver. Pull the Burner ON/OFF control box from
inside the bottom of the fireplace and position the slots in the bracket
over the 2 screws on the left side of the bottom louver. Push down
to lock into place. Tighten the screws.
Bay Louver Top
Heat Shield
Burner ON/OFF
control box
3) Install top louver by sliding the two bracket clips into the brackets
located on top of the bay door. See below. The fitted louver leaves
a small gap between faceplate bottom and louver top.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
FULL SCREEN FRONT
1) Before beginning the installation, remove the Glass Door from the
unit. Refer to the manual for instructions.
2) Slide the Bottom Face Plate Bracket into the bottom of the unit,
secure it into the pins located on the inside of the fire box. Once the
bracket is in place, tighten the screws into the hinges on the left and
right sides.
4) a)
b)
Before attaching the Full Screen Door Frame to the unit,
loosen the left and right side #8 Self Tapping Philips screws
located on the inside top of the outer frame of the appliance.
Also remove the center screw.
Slide the cut-outs in the Top and Bottom Flange of the Full
Screen Door Frame under the screw heads which were
loosened in step 4a). Once the Frame is in place, tighten
the screws to secure. Also re-secure the top center screw
through the oblong hole.
Full Screen Door
Frame
Bottom Faceplate
Bracket
Pin location
Cut-Out
Oblong Hole
Faceplate
Mounting
Bracket
Cut-Out
Screw
Top
Flange
3) Before attaching the Full Screen Door Frame, remove the Screen
Doors from the Full Screen Door Frame by fully opening the doors
and lifting up off of the hinges. See important note in step 10.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Bottom
Flange
Backside of Full
Screen Door
Frame Shown
Cut-Outs
INSTALLATION
NOTE: Should the finished wall protrude beyond the face of the unit,
you can accommodate up to 1/2" depth.
Simply push in the Full Screen Door Frame until it aligns against
the finished wall. Secure Top Flange of Full Screen Door Frame as
described in step 4 b).
8) Re-install Glass Door. Refer to the manual for instructions.
9) Slide the Top Grill into the louver brackets located on the inside top
of the firebox. Push in place.
For the Bottom Flange of the Full Screen Door Frame, push the bottom of the Frame until it aligns with the wall. Use the inner cut-outs to
secure the base of the Frame using the 2 x #8 Self Tapping Phillips
screws provided.
5) Install the Hinges to the Hinge Brackets on the left and right side of
the Bottom Faceplate Bracket (seen in step 2), secure using 2 x #8
Self Tapping Philips screws per hinge.
Top Grill
6) Place the Bottom Frame near the hinges, and flip down the hinges
from the Bottom Face Plate. Secure the hinges in place to the Bottom
Frame, using 2x #8 Self Tapping Phillips screws per hinge.
10) Install the Left and Right Side Screen Doors in the fully open position
by placing over top of the hinges on the Full Screen Door Frame.
NOTE: Failure to install the doors in the fully open position could
result in paint damage to the surface of the door.
Hinge Location
Bottom Grill
Hinge
7) Mount the Burner ON/OFF Control Box to the left side of the Bottom
Grill using 2 x #8 - 1/4" Philips Head Screws.
Left Side
of Bottom
Grill
Screen Door
Burner ON/OFF
Control Box
11) Close screen doors.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
OPTIONAL
WALL THERMOSTAT
A wall thermostat may be installed if desired,
connect the wires as per the wiring diagram.
Use table below to determine the maximum
wire length.
Note: Preferable if the thermostat is installed
on an interior wall.
Regency offers an optional programmable
thermostat but any 250-750 millivolt rated nonanticipator type thermostat that is CSA, ULC or
UL approved may be used.
CAUTION
Do not wire millivolt
wall thermostat wires
to 120V wire.
Thermostat Wire Table
Recommended Maximum Lead Length
(Two-Wire) When Using Wall
Thermostat (CP-2 System)
Wire Size
14 GA.
16 GA.
18 GA.
20 GA.
22 GA.
OPTIONAL
REMOTE CONTROL
OPTIONAL
WALL SWITCH
Use the Regency Remote Control Kit approved
for this unit. Use of other systems may void
your warranty.
1) Run the supplied 15' of wire through the right
or left side gas inlet opening. Be careful not
to damage wire.
The remote control kit comes with a hand
held transmitter, a receiver and a wall mounting plate.
Note: We recommend a maximum of 15'
of wire but if you wish to go with a
longer run, use the Thermostat Wire
Table.
1) Choose a convenient location on the wall
to install the receiver and the receptacle
box (protection from extreme heat is very
important). Run wires from the fireplace to
that location. Use Thermostat Wire Table.
2) Connect the two wires to the gas valve.
See diagram below.
CAUTION
Do not wire millivolt
remote control wires
to 120V wire.
3) Install 3 AAA alkaline batteries in transmitter
and 4 AA alkaline batteries in the receiver.
Install the receiver and its cover in the wall.
Switch the remote receiver to "remote"
mode. The remote control is now ready for
operation.
Max. Length
50 Ft.
32 Ft.
20 Ft.
12 Ft.
9 Ft.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
2) Connect the wire to the supplied wall switch
and install into the receptacle box.
CAUTION
Do not wire millivolt
wall switch wire
to 120V wire.
INSTALLATION
WIRING DIAGRAM
This heater does not require a 120V A.C. supply for operation. In case of a power failure, the burner switch and the optional remote control/thermostat
will continue to operate. However, a 120V A.C. power supply is needed for the fan/blower operation.
(Do not cut the ground terminal off under any circumstances.)
Thermopile
Lockwasher
Star washer
#8 Ground Lug
(mobile home
approved)
Electrode
Thermocouple
Even if the fan is not purchased with the unit, it is still a good idea to bring power to the receptacle box (provided with the unit)
in case the fan is installed at a later date.
Gas Pilot
NOTE:
Fan
Ground
Neutral
120V AC
60 Hz
Live
Green
Ground
ON
Pilot
Assembly
OFF
Black
Red
Red
Nut
Minimum Convection
Air Temp. Switch
Rotary Speed
Control
Fan
ground wire
Piezo
Ignitor
(To THTP)
L
Brown
White
O
OFF
I
(To TH)
To Thermocouple IN
PILO
T
Red
Black
ON
White
H
Burner ON
OFF
Thermostat
Gas
In
"S.I.T" Valve
T-Stat
Remote Receiver
or Thermostat
(Millivolt) (Optional)
Regency
ON OFF
Remote Transmitter
(Optional)
Caution: Ensure that the wires do
not touch any hot surfaces and are
away from sharp edges.
CAUTION: Label all wires
prior to disconnection
when servicing controls.
Wiring errors can cause
improper and dangerous
operation.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
INSTALLATION
INSTALLING THE OPTIONAL FAN
120 Volt AC power is needed for the fan switch
and blower. The fan can be hard wired if desired.
The receptacle box should be installed on the
left hand side of the unit by a qualified electrician. The neutral (wider) slot of the polarized
receptacle should be at the top.
11) Attach the two control boxes to the bottom
louver and tighten the 2 screws on the left
side and 1 screw on the right side.
Unit must be grounded at all times. Do
not cut the ground terminal off under any
circumstances.
1) Shut the power off.
Diagram 2
2) Remove the standard flush door and the
optional bay door, if installed. Open the
bottom louver door.
Secure left side with 2 screws.
3) Loosen the 2 screws holding the Burner
ON/OFF switch and bracket to the bottom
louver and lift the assembly out.
Diagram 3: Use the clip & hook on the side of
the control boxes to join them together.
8) Secure the two boxes together with one
screw.
Secure right side with one screw.
4) Turn the fan base on its side (with the base
facing towards you) and then slide the fan
in towards the rear of the unit. Turn the fan
upright and slip it over the two mounting
studs. Take care not to damage the insulation
on the fan base. Ensure that the fan blades
do not rub against the valve tubing.
Diagram 1.
Secure the 2 boxes together
with one screw.
9) Position the control box assembly on the
bottom louver and mark the position of the
slot on the right side bracket.
5) Connect fan ground cable to ground lug.
Refer to wiring diagram.
13) Plug the fan power cord into the rear end of
the receptacle box to provide the maximum
clearance from the louvers.
6) Slide the thermodisc/cover assembly into
the bracket clip on the underside of the
firebox. Check that no wire will touch the
hot surfaces. Diagram 2.
7) Attach the Fan control box to the Burner
ON/OFF control box. Diagram 3.
12) Secure the fan wires and power cord by
attaching one of the adhesive backed wire
holder clips (Part #910-199) onto the stove
base. Use the second clip to bundle up the
wires approximately 4" from the control box.
Ensure that there is no interference with the
wires when the louver is closed and that
no wire will touch the hot metal surfaces or
sharp edges.
TO REMOVE THE FAN
1) Shut the power off.
Hold control box assembly in place and
mark the position of the right side slot
10) Remove the control box assembly and push
the hold-down clip onto the louver. Bend the
tab until it is at 90o to the louver.
Push hold-down clip onto inside
louver and press tab until it is
at 90o to
louver.
Diagram 1
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
2) Reverse the above instructions.
Note: The bearings are lubricated for life.
Do not lubricate them. Make sure
you vacuum the fan area on a regular
basis.
IMPORTANT:
These fans collect a lot of dust from within
your home. Ensure you maintain these fan
motors on a regular basis by vacuuming
out the fan blades and housing using a soft
brush nozzle.
OPERATING INSTRUCTIONS
COPY OF THE LIGHTING PLATE INSTRUCTIONS
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
OPERATING INSTRUCTIONS
OPERATING
INSTRUCTIONS
1) Read and understand these instructions
before operating this appliance.
2) Check to see that all wiring is correct and
enclosed to prevent possible shock.
3) Check to ensure there are no gas leaks.
4) When the pilot stays lit, turn the gas knob
further counterclockwise to the "ON" position.
DO NOT BURN THE APPLIANCE
WITHOUT THE GLASS FRONT IN
PLACE.
5) Use the wall switch, thermostat or remote
control to turn on the unit.
During the first few fires, a white film may
develop on the glass front as part of the curing
process. The glass should be cleaned or the
film will bake on and become very difficult
to remove. Use a non-abrasive cleaner and
NEVER clean the glass while it is hot.
6) Rotate the flame height regulator to adjust
the flame height higher or lower.
4) Make sure the glass in the door frame is
properly positioned. Never operate the appliance with the glass removed.
AERATION
ADJUSTMENT
5) Verify that the venting and cap are unobstructed.
The air shutter can be adjusted by moving the
adjusting wire up or down. The wire is accessed
through the bottom louver opening. Open the air
shutter for a blue flame or close for a yellower
flame. The burner aeration is factory set but
may need adjusting due to either the local gas
supply or altitude.
6) Ensure that the brick panels are installed.
7) Verify log placement. If the pilot cannot be
seen when lighting the unit, the logs have
been incorrectly positioned.
8) The unit should never be turned off, and on
again without a minimum of a 60 second
wait.
SHUTDOWN
PROCEDURE
LIGHTING PROCEDURE
IMPORTANT
To ignite or reignite the pilot,
you must first release the tension springs below the door.
Only when the pilot holds, without pressure
being applied to the control knob, reapply the
tension springs to the door. The unit must
not be operated with the tension springs
unattached.
IMPORTANT: Gas cock knob cannot be turned
from "PILOT" to "OFF" unless it is partially
depressed.
1) Turn burner OFF using "ON/OFF" switch.
2) Turn gas control knob so indicator points to
"OFF" position and allow 5 minutes for any
gas in the combustion chamber to escape.
3) Turn gas control knob counterclockwise
so indicator points to the "PILOT" position.
Depress the gas control knob fully. Depress
the igniter button several times until the
pilot lights. After approximately one minute,
release the gas control knob. The pilot flame
should continue to burn. If the pilot does not
remain lit, repeat operation allowing a longer
period before releasing gas control knob.
1) Use the wall switch, thermostat or remote
control to turn off the main burner.
Minimum Air Shutter Opening:
3/16"
Natural Gas
3/8"
Propane
CAUTION: Carbon will be produced if air shutter
is closed too much.
2) Turn the main gas control clockwise to the
"OFF" position to turn off the pilot.
3) Turn off all electric power to appliance if
service is to be performed.
Air
shutter
FIRST FIRE
The first fire in your stove is part of the paint curing process. To ensure that the paint is properly
cured, it is recommended that you burn your
fireplace for at least four (4) hours the first time
you use it with the fan on.
When first operated, the unit will release an odour
caused by the curing of the paint, the burning
off of any oils remaining from manufacturing.
Smoke detectors in the house may go off at this
time. Open a few windows to ventilate the room
for a couple of hours.
The glass panel may require cleaning after the
unit has cooled down. DO NOT ATTEMPT TO
CLEAN THE GLASS WHILE IT IS HOT.
Note: When the glass is cold and the appliance is lit, it may cause condensation
and fog the glass. This condensation
is normal and will disappear in a few
minutes as the glass heats up.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
wire
Adjustment Wire: push to close
or pull to open aeration cap
Closed - Tall yellow
Open - Short blue
Note: Any damage due to carboning resulting from improperly setting the aeration controls is NOT covered under
warranty.
Note: Aeration Adjustment should only be
performed by an authorized Regency
Installer at the time of installation or
service.
MAINTENANCE
NORMAL OPERATING
SOUNDS OF
GAS APPLIANCES
It is possible that you will hear some sounds
from your gas appliance. This is perfectly normal
due to the fact that there are various gauges
and types of steel used within your appliance.
Listed below are some examples. All are normal
operating sounds and should not be considered as defects in your appliance.
Blower:
Regency gas appliances use high tech blowers to push heated air farther into the room. It
is not unusual for the fan to make a "whirring"
sound when ON. This sound will increase or
decrease in volume depending on the speed
setting of your fan speed control.
Burner Tray:
The burner tray is positioned directly under the
burner tube(s) and logs and is made of a different gauge material from the rest of the firebox
and body. Therefore, the varying thicknesses
of steel will expand and contract at slightly
different rates which can cause "ticking" and
"cracking" sounds. You should also be aware
that as there are temperature changes within
the unit these sounds will likely re-occur. Again,
this is normal for steel fireboxes.
Blower Thermodisc:
When this thermally activated switch turns ON
it will create a small "clicking" sound. This is the
switch contacts closing and is normal.
Pilot Flame:
While the pilot flame is on it can make a very
slight "whisper" sound.
Gas Control Valve:
As the gas control valve turns ON and OFF, a
dull clicking sound may be audible, this is normal
operation of a gas regulator or valve.
Unit Body/Firebox:
Different types and thicknesses of steel will
expand and contract at different rates resulting
in some "cracking" and "ticking" sounds will be
heard throughout the cycling process.
MAINTENANCE
INSTRUCTIONS
1) Always turn off the gas valve before cleaning.
For relighting, refer to lighting instructions.
Keep the burner and control compartment
clean by brushing and vacuuming at least
once a year. When cleaning the logs, use a
soft clean paint brush as the logs are fragile
and easily damaged.
2) Clean appliance and door with a damp
cloth (never when unit is hot). Never use
an abrasive cleaner. The glass should be
cleaned with a gas fireplace glass cleaner.
The glass should be cleaned when it
starts looking cloudy.
3) The heater is finished in a heat resistant
paint and should only be refinished with heat
resistant paint. Regency uses StoveBright
Paint - Metallic Black #6309.
4) Make a periodic check of burner for proper
position and condition. Visually check the
flame of the burner periodically, making sure
the flames are steady; not lifting or floating.
If there is a problem, call a qualified service
person.
5) The appliance and venting system must be
inspected before use, and at least annually,
by a qualified field service person, to ensure
that the flow of combustion and ventilation
air is not obstructed.
Note:
Never operate the appliance without
the glass properly secured in place.
6) Do not use this appliance if any part has been
under water. Immediately call a qualified
service technician to inspect the appliance
and to replace nay part of the control system
and any gas control which has been under
water.
3) Check for evidences of excessive condensation, such as water droplets forming in the
inner liner, and subsequently dripping out the
joints, Continuous condensation can cause
corrosion of caps, pipe, and fittings. It may
be caused by having excessive lateral runs,
too many elbows, and exterior portions of the
system being exposed to cold weather.
4) Inspect joints, to verify that no pipe sections
or fittings have been disturbed, and consequently loosened. Also check mechanical
supports such as Wall Straps, or plumbers'
tape for rigidity.
GOLD-PLATED or
BRASS LOUVERS/TRIM
The 24 carat gold-plated or brass finish on the
louvers and trim requires little maintenance,
and need only be cleaned with a damp cloth.
DO NOT use abrasive materials or chemical
cleaners, as they may harm the finish and void
the warranty. Clean any fingerprints off before
turning the unit on.
LOG REPLACEMENT
The unit should never be used with broken logs.
Turn off the gas valve and allow the unit to cool
before opening door and carefully remove the
logs. (The pilot light generates enough heat to
burn someone.) If for any reason a log should
need replacement, you must use the proper
replacement log. The position of these logs
must be as shown in the diagrams under Log
Installation.
Note: Improper positioning of logs may create carbon build-up and will severely
alter the unit's performance which is
not covered under warranty.
7) Verify operation after servicing.
General Vent Maintenance
Conduct an inspection of the venting system
semi-annually. Recommended areas to inspect
as follows:
1) Check the Venting System for corrosion in
areas that are exposed to the elements.
These will appear as rust spots or streaks,
and in extreme cases, holes. These components should be replaced immediately.
2) Remove the Cap, and shine a flashlight
down the Vent. Remove any bird nests, or
other foreign material.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
MAINTENANCE
THERMOPILE/
THERMOCOUPLE
1) Open the bottom louvers.
2) Loosen the thermocouple or thermopile with
a 7/16" wrench.
Flush Glass Replacement
Bay Glass Replacement
Remove the flush door front. Remove the 4
glass clips from each corner. Slide in the new
replacement glass. Push the 4 glass clips back
onto the frame. The glass must have gasketing around it.
1) Remove the door from the unit and place on
a soft surface to prevent scratching.
3) Disconnect thermocouple by loosening nut
from the valve with a 9mm wrench. Disconnect thermopile by loosening 2 screws
marked TP on the valve.
4) Drop the thermocouple or thermopile down
from the bracket and pull it out of the unit.
5) Reinstall the new ones in reverse order.
GLASS GASKET
If the glass gasket requires replacement use
5/8" flat glass gasket for the Bay Front (Part
# 936-243) and a tadpole glass gasket for the
Flush Front (Part # 936-155).
DOOR GLASS
Your Regency stove is supplied with high
temperature, 5 mm Neoceram ceramic glass
that will withstand the highest heat that your
unit will produce. If your glass requires cleaning, we recommend using an approved glass
cleaner available at all authorized dealers. Do
not use abrasive materials. Do not clean the
glass when hot.
In the event that you break your glass by impact,
purchase your replacement from an authorized
Regency dealer only, and follow our step-by-step
instructions for replacement.
WARNING: Do not operate the
appliance with the glass panels
removed, cracked or broken.
Replacement of the glass panels
should be done by a licensed or
qualified service person.
Caution:Weargloveswhenremoving
damaged or broken glass.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
2) Remove the nuts holding the glass clips in
place and remove.
3) Replace the glass. The glass must have
gasketing around it.
5) Reverse the previous steps, replace the glass
clips and fasten with the nuts but do not over
tighten, as this can break the glass.
6) Replace door on the stove and check the
seal.
MAINTENANCE
REMOVING VALVE
1) Shut off the gas supply.
10) Undo the pilot tube from the valve with a
7/16" wrench.
INSTALLING VALVE
1) Attach the valve to the valve bracket with
the 4 (m5x8 metric) screws provided.
2) Remove the louvers (and bay door if it is
on).
2) Reconnect the "gas out" flare fitting with
an 11/16" wrench.
3) Open the flush door and remove the door.
4) Remove the logs.
3) Reconnect the "gas out" flare nut with a
13/16" wrench.
5) Remove the burner/grate assembly by
removing the two Phillips head screws and
then lift the burner assembly out.
4) Install piezo ignitor push button assembly
and reconnect wire.
5) Reconnect the quick drop out thermocouple
nut with a 9mm wrench.
Diagram 3: Lift out Valve Tray Assembly
6) Reconnect the pilot tube nut with a 7/16"
wrench.
7) Scrape off the old gasket from the floor of the
firebox and from the valve tray assembly.
8) Install a new gasket and reinstall the valve
tray assembly.
11) Undo the quick drop out thermocouple nut
on the valve with a 9mm (metric) wrench.
12) Remove the Piezo igniter wire and push
button assembly.
Diagram 1: Remove the left and right screws
and then lift out the burner/grate assembly.
6) Remove the rear log stand by removing the
2 screws.
7) Disconnect the inlet gas line. See diagram
2.
8) Disconnect the 2 TP wires and the 2 TH
wires from the valve.
9) Remove the 10 Phillips head screws securing the valve tray assembly in place (diagram
2) and then lift the entire assembly out
(diagram 3).
screws
13) Undo the "gas out" flare nut with a 13/16"
wrench.
Note: Failure to install a new gasket may
severely affect the appliance performance.
9) Reinstall the 10 hold down screws.
10) Hook up the 2 TP and 2 TH wires to the
appropriate connections on the valve.
11) Reinstall the front log stand.
14) Undo the "gas out" flare fitting with an 11/16"
wrench.
12) Install Burner/grate assembly.
15) Remove the 4 Phillips head screws from
the sides of the valve bracket and remove
valve.
13) Hook up the gas line and check for gas
leaks with a soap and water solution or a
gas leak detector. (Do not use open flame
for leak testing.)
Hint: If you are using black pipe, ensure that
there is a union by the valve, otherwise removal
will be almost impossible.
Rear Log Stand
14) Fire up the unit temporarily.
15) Check the manifold pressure.
16) Reinstall the logs and brick panels as
needed.
17) Close the door and replace the louvers.
18) Fire up the unit again and check for proper
flame appearance and glow on logs.
Valve Tray Assembly
screws
Diagram 2: Rear Log Stand & Valve Tray Assembly
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
PARTS LIST
Main Assembly
Part #
Description
1) 948-247
2) *
Door Handle
Thermodisc Bracket
7) 910-428
8) 910-429
9) 910-430
10) 904-687
13) 948-045
14) 948-115
Duplex Receptacle
Box - Receptacle
Cover - Receptacle
Clamp Connector
#12 Jack Chain
Door Extension Spring
16) *
17) *
19) 430-129
Thermodisc Top
Thermodisc Box Base
Receptacle Box Mount
20) 430-031
21) 430-032
22) 433-017
23) 433-011F
24) 511-044
790-091
26) *
27) *
28) *
30) *
31) *
Top Nailing Strip
Side Nailing Strip
Firebox Baffle
Top Standoff
Standoff - Side
Standoff - Rear
Louver Hold Down
Outer Flue Collar
Inner Flue Collar Assembly
Gasket - Flue Collar
Flue Mounting Plate
Part #
432-928
432-901
432-902
432-903
432-904
33) *
34) *
35) *
36) *
37) 430-056
38) 430-057
432-945
902-359
902-358
902-360
902-361
432-917
Description
Brick Panel Set - Standard
Brick Panel Set - Standard Brown
Brick Panel Set - Standard Red
Brick Panel Set - Herringbone
Brown
Brick Panel Set - Herringbone Red
Brick Panel - Rear
Brick Panel - Left Side
Brick Panel - Right Side
Brick Panel - Top
Brick Clip - Top
Brick Clip - Bottom
Herringbone Brick Panel Set
(Optional)
Brick Panel - Rear
Brick Panel - Left Side
Brick Panel - Right Side
Brick Panel - Top
Fan Assembly (120 Volts)
Optional
42) 910-331/P Fan Motor (120 Volts)
432-966 Fan Switch Assy (120 Volts)
43) 910-813 Power Cord (120 Volts)
46) 910-330 Fan Speed Control
47) 904-586 Knob - Speed Control
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Part #
49) 910-142
50) 904-713
432-967
63) 910-241
910-899
Description
Thermodisc - Fan Auto ON/OFF
U-Clip at Louver
Burner On/Off Switch Assy
Switch - Burner On/Off
Wire Harness - Valve to Burner
946-556
89) 946-004
90) 946-000
91) 946-002
92) 946-001
93) 946-007
94) 946-517/P
Optional Heat Wave Duct Kit
Junction Box
Round Duct Adaptor
Round to Oval Adaptor
Oval Duct Adaptor
Angle Bracket
Fan Assembly - HeatWave
Option
95) 946-006
Grill Plate - White
96) 946-005
Wall Adaptor Plate - White
97) 910-417
Knob - White
98) 910-366
Switch Cover Plate - White
99) 910-412
Fan Speed Controller
100) 910-367 Box - Plastic Switch
Receptacle
102) 946-010 Flexible Air Duct
946-038
Insulation 6" dia. x 24"
104) 690-022F Cover Plate
510-994
918-262
431-969
Dura-Vent Adaptor
Manual
Conversion Kit - NG to LP
PARTS LIST
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
PARTS LIST
Burner & Log Assembly
Part
Description
53) 430-055
54) 910-421
55) 910-422
56) 910-190
Gasket - Valve Access Plate - NG/LP
Pilot ON/OFF Extension Knob
Flame HI/LOW Extension Knob
Piezo Ignitor and Nut
433-574/P
433-576/P
57) 910-378
910-380
58) *
59) *
60) *
66) 910-038
910-039
904-568
904-163
936-170
67) *
68) W840470
79) 433-525
82) 433-024
83) *
85) 431-930
86) 430-097
87) 433-018
Valve Assy - Natural Gas
Valve Assy - Propane
S.I.T. Valve - Natural Gas
S.I.T. Valve - Propane
Valve Bracket
Firebox Base
Valve Tray
Pilot Assy - 3 way flame - S.I.T. - NG
Pilot Assy - 3 way flame - S.I.T. - LP
Orifice #44 - Natural Gas
Orifice #54 - Propane
Orifice Gasket
Pilot Holder
Pilot Assembly Gasket
Burner Assy - NG/LP
Burner Grate Assembly - NG/LP
Rear Log Support Bracket - NG/LP
Log Set
Air Deflector-Left
Air Deflector-Right
*Not available as a replacement part.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
PARTS LIST
Flush Front & Louvers
Part #
Description
117) 904-196
130) 430-924
131) 430-926
430-947
Magnet - 1' round
Flush Glass Trim (set) - Gold (Option)
Flush Glass Trim (set) - Brass (Option)
Flush Glass Trim (set) - Brushed Steel (Option)
430-918
430-920
430-922
430-923
133) *
430-162
134) *
Flush Louvers (set) - Gold/Black (Option)
Flush Louvers (set) - Brass/Black (Option)
Flush Louvers (set) - Black (Option)
Flush Louvers (set) - Black/Steel (Option)
Flush Louver Assy-Top
Front Deflector
Flush Louver Assy-Bottom
135)
137)
139)
140)
433-538
940-088/P
904-691
936-155
948-042
Flush Door Assembly Complete
Glass (Flush)
U-Clip
Glass Gasket (Tadpole)
Spring Hinge - Black
Part #
430-940
430-942
157) *
159) *
158) *
171)
172)
173)
174)
175)
178)
431-943
*
*
904-712
430-133
511-084
*
904-715
*
179) 948-216
Description
Finishing Trim (Set) - Black (Option)
Finishing Trim (Set) - Brass (Option)
Finishing Trim Left
Finishing Trim Right
Finishing Trim Top
Double Screen Door Complete (Option)
Door Frame Left Assembly
Door Frame Right Assembly
U-Clip for Frame
Door Handle
Door Latch
Door Support Frame Assembly
Pushnut Fastener 3/16"
Screw - #8 x 1/2"
Regency Logo Plate
*Not available as a replacement part.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
PARTS LIST
Bay Front & Louvers
106)
107)
108)
110)
111)
112)
117)
118)
120)
Part #
Description
430-930
940-079/P
936-243
940-078/P
*
902-322
432-905
432-906
*
904-196
*
400-189
Bay Front Complete
Side Glass
Glass Gasket
Center Glass
Bay Door Frame
Bay Brick Panel - Standard
Bay Brick Panel - Standard Brown
Bay Brick Panel - Standard Red
Bay Brick Panel Spacer
Magnet (1" round)
Louver Hold Down
Glass Retainer
432-956
432-954
432-958
123) *
125)
126)
129)
130)
131)
430-932
430-934
430-936
430-937
*
433-026
*
948-042
432-960
948-216
Bay Door Trim (set) - Gold
Bay Door Trim (set) - Brass
Bay Door Trim (set) - Brushed Steel
Bay Door Trim (each) - Black
Bay Louvers (set) - Gold/Black
Bay Louvers (set) - Brass/Black
Bay Louvers (set) - Black
Bay Louvers (set) - Steel/Black
Bay Louver Assy-Top
Bay Door Deflector
Bay Louver Assy-Bottom
Hinge
Bay Front Screen
Regency Logo Plate
*Not available as a replacement part.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
NOTES
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
___________________________________________________
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
WARRANTY
Regency Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance Team carefully inspects each unit
thoroughly before it leaves our facility. FPI Fireplace Products International Ltd. is pleased to extend this limited lifetime warranty to the original purchaser of a
Regency Product. This warranty is not transferable.
The Warranty: Limited Lifetime
The combustion chamber, heat exchanger, burner tubes/pans, logs, brick panels and gold plating (against defective manufacture only) are covered under the Limited Lifetime
Warranty for five (5) years for parts and subsidized labour* and parts only thereafter.
Glass is covered for lifetime against thermal breakage only, parts and subsidized labour* for five (5) years and parts only thereafter from date of purchase.
External casting, surrounds and grills are covered against cracks and warps resulting from manufacturer defects, parts and subsidized labour* for three (3) years from the date
of purchase and parts only thereafter.
Special Finishes - One year on brushed nickel and antique copper full screens and doors. You can expect some changes in color as the product "ages" with constant heating
and cooling. FPI warranties the product for any manufacturing defects on the original product. However, the manufacturers warranty does not cover changing colors and marks,
ie. finger prints, etc applied after the purchase of the product. Damage from the use of abrasive cleaners is not covered by warranty.
Electrical and mechanical components such as blowers, switches, wiring, thermodiscs, FPI remote controls, spill switches, thermopiles, thermocouples, pilot assembly components,
and gas valves are covered for one year parts and subsidized labour* from the date of purchase. Blowers and valves replaced under warranty are considered repairs and continue
as if new with appliance. ie. twelve (12) months from original purchase date of appliance with a minimum of three (3) months coverage from date of replacement.
FPI venting components are covered parts and subsidized labour* for three (3) years from date of purchase.
Simpson Dura-Vent venting components (Direct Vent units) are covered by Simpson Dura-Vent Inc. warranty.
Conditions:
Any part or parts of this unit which in our judgement show evidence of such defects will be repaired or replaced at FPI's option, through an accredited distributor or agent provided
that the defective part be returned to the distributor or agent Transportation Prepaid, if requested.
Porcelain/Enamel - Absolute perfection is either guaranteed nor commercially possible. Any chips must be reported and inspected by an authorized dealer within three days of
installation. Reported damage after this time will be subject to rejection.
It is the general practice of FPI to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned to FPI and evaluated
for manufacturer defect.
The authorized selling dealer is responsible for all in-field service work carried out on your Regency product. FPI will not be liable for results or costs of workmanship from
unauthorized service persons or dealers.
At all times FPI reserves the right to inspect product in the field which is claimed to be defective.
All claims must be submitted to FPI by authorized selling dealers. It is essential that all submitted claims provide all of the necessary information including customer name,
purchase date, serial #, type of unit, problem, and part or parts requested, without this information the warranty will be invalid.
Exclusions:
This limited Lifetime Warranty does not extend to or include paint, door or glass gasketing or trim.
At no time will FPI be liable for any consequential damages which exceed the purchase price of the unit. FPI has no obligation to enhance or modify any unit once manufactured.
ie. as products evolve, field modifications or upgrades will not be performed.
FPI will not be liable for travel costs for service work.
Installation and environmental problems are not the responsibility of the manufacturer and therefore are not covered under the terms of this warranty policy.
Embers, rockwool, gaskets, door handles and paint are not covered under the terms of this warranty policy.
Any unit which shows signs of neglect or misuse is not covered under the terms of this warranty policy.
The warranty will not extend to any part which has been tampered with or altered in any way, or in our judgment has been subject to misuse, improper installation, negligence
or accident, spillage or downdrafts caused by environmental or geographical conditions, inadequate ventilation, excessive offsets, negative air pressure caused by mechanical
systems such as furnaces, fans, clothes dryer, etc.
Freight damage to stoves and replacement parts is not covered by warranty and is subject to a claim against the freight carrier by the dealer.
FPI will not be liable for acts of God, or acts of terrorism, which cause malfunction of the appliance.
Performance problems due to operator error will not be covered by this warranty policy.
Products made or provided by other manufacturers and used in conjunction with the operation of this appliance without prior authorization from Regency, may nullify your
warranty on this product.
Any alteration to the unit which causes sooting or carboning that results in damage to the interior / exterior facia is not the responsibility of FPI.
* Subsidy according to job scale as predetermined by FPI.
Regency P33-3 Zero Clearance Direct Vent Gas Fireplace
Regency fireplace products are designed
with reliability and simplicity in mind.
In addition, our internal QualityAssurance
Team carefully inspects each unit
thoroughly before it leaves our
door.
Fireplace Products International
Ltd. is pleased to extend this
Limited Lifetime Warranty to the
original purchaser of a Regency
Product.
See the inside back cover for details.
Register your Regency online at
http://www.regency-fire.com
Installer: Please complete the following information
Dealer Name & Address: ______________________________________________
___________________________________________________________________
Installer: ___________________________________________________________
Phone #: ___________________________________________________________
Date Installed: ______________________________________________________
Serial No.: __________________________________________________________
Regency and Panorama are trademarks of FPI Fireplace Products International Ltd.
© Copyright 2006, FPI Fireplace Products International Ltd. All rights reserved.
Printed in Canada