Zhone Hotwire 6381 Instruction manual

Hotwire® ADSL/R Bridge/Router, Model 6381
with Inline Phone Filter
Installation Instructions
Document Number 6381-A2-GN10-10
April 2003
Installation Procedures
To install the Hotwire ADSL/R Bridge/Router:
Verify the contents of the package and obtain the correct cables (see Package
Checklist on page 2 and Wiring and Cables You Need (not supplied) on page 2)
Install phone filters on all phones that will share the same phone line as the router
(see Installing Phone Filters on page 3)
Connect the router (see Installing the Hotwire ADSL/R Bridge/Router on page 4)
Verify that the front panel LEDs show the correct status (see LED Status on page 7)
If necessary, configure the router (see Configuring the Hotwire ADSL/R
Bridge/Router on page 8)
Definitions
The following terms are used in this booklet.
network
A group of connected things, such as telephones or computers.
bridge
A device that forwards any message from one part of a network to
another. The Hotwire ADSL/R Bridge/Router is shipped as a bridge.
router
A device that forwards messages according to their network
addresses. You must configure the Hotwire ADSL/R Bridge/Router to
make it work as a router.
POTS
Plain Old Telephone Service. The voice service provided over the
public switched telephone network (PSTN).
DSL
Digital Subscriber Line. The technology that allows you to use a POTS
line for both voice calls and high-speed Internet access
simultaneously.
ADSL
Asymmetric DSL. A version of DSL that allows a higher speed for
information coming from the Internet to your PC (“downstream”) than
it does for information going to the Internet from your PC (“upstream”).
ReachDSL
A proprietary Paradyne version of DSL that works on lines too long or
too noisy for ADSL.
ADSL/R
The technology that combines ADSL and ReachDSL in one device.
1
Package Checklist
Verify that your package contains the following:
Rea
chD
SL
PWR
ALM
TST
LINE
TX/R
X
ETH
ERN
ET
Hotwire 6381
ADSL/R
Bridge/Router
DSL interface cable
with RJ11 connectors
Power cord with
power transformer
Ethernet 8-pin
cable
Two ferrite clamps
Wiring and Cables You Need (not supplied)
The following standard cables and connectors are used with this product:
Standard RJ11
(or RJ14) wall jack for
the DSL cabling
2
Installing Phone Filters
IC
E
SERV
P/N
TM
in
e
PROD
ad
L. AC
T.E
CE
. EQ
E1 SS
00 UIPMAR
29 Y
6 EN
T
R
M
UCT
Ch
geprufte
Sicherheit
TU
Y
Ph
o
08 ne
02 F
in
a
-3
Be / Fa 39
l Fu br
2se iquè 00
In Ch
c.
11 ina
98
ilt
er
E
N
LI
A phone filter is recommended to minimize
background noise during a phone conversation on
telephones not connected directly to the Hotwire
ADSL/R Bridge/Router. If additional telephones in
your home or business share the same phone line
with the router, install one phone filter on each
telephone. A fax machine or other equipment that
uses the same POTS line as the router must also use
a filter.
LR9
2997
N
O
PH
E
There are two Hotwire phone filters available:
Hotwire 6035 Universal Phone Filter is designed for use with a tabletop phone.
Hotwire 6040 Wall Jack Phone Filter is designed for use with a wall phone.
Customer
Premises
Router
RJ11
Wall
Jack
POWER
ETHER
NET
PHONE
RJ11
Wall Jack
LINE
6035
Phone Filter
6040
Wall Jack
Phone
Filter
03-17355
Contact your sales or service representative to order Hotwire phone filters.
3
Installing the Hotwire ADSL/R Bridge/Router
Place the router on a flat surface with clearance for the rear connectors.
Procedure
1. UNPLUG TELEPHONE. If a telephone is connected at
RJ11
Wall Jack
the RJ11 wall jack where the router will be installed,
unplug the telephone cable from the wall jack.
2. RECONNECT TELEPHONE.
PHONE
(Optional. Go to Step 3 if you are not
connecting a telephone to the router.)
POWE
R
ETHERN
Plug the existing telephone cable that was
unplugged in Step 1 into the jack labeled
PHONE. The router has a built-in filter, so
no filter is required on this phone.
PHON
E LIN
E
3. CONNECT DSL LINE. Use the supplied
RJ11 telephone cable for the ADSL/R line
connection. Insert one end of the cable into
the jack labeled LINE. Insert the other end
of the cable into the RJ11 wall jack.
ET
LINE
PHONE
LINE
RJ11
6-pin
Interface
Cable
4
58
173
02-
RJ11
Wall
Jack
4. INSTALL WHITE FERRITE CLAMP. If you
plugged in a phone, install the supplied
white ferrite clamp around both the LINE
and PHONE cables. If you did not plug in a
phone, install the white clamp around the
LINE cable.
LINE
PHONE
PHONE
LINE
59
173
02-
Hold the open clamp around the cable or
cables as close to the router as possible.
Close the clamp and lock it by pressing on
the latch.
5. CONNECT TO PC OR ETHERNET HUB. Use an 8-pin Ethernet cable
(straight-through or crossover) for the Ethernet connection. Insert one end of the
cable into the jack labeled ETHERNET.
Connect to one of the following:
—
PC. Use an Ethernet standard,
straight-through cable and connect
the other end to a PC with an
Ethernet Network Interface Card
(NIC) installed.
ETHERNET
POWER
03-17360
-01
– or –
—
ETHERN
ET
PC with Ethernet
Network Interface
Card
Ethernet
Straight-Through
Cable
Ethernet Hub. Use an Ethernet
standard, straight-through cable
and connect the other end to an
Ethernet hub’s Uplink port. (To
connect to a hub’s standard port,
use an Ethernet crossover cable.
See the documentation that came
with your hub.)
ETHERNET
POWER
02-17361
-01
Ethernet
Hub
ETHERN
ET
1
2
3
4
5
6
7
6. INSTALL BLACK FERRITE CLAMP.
8
Hold the open clamp around the
Ethernet cable as close to the router as
possible. Close the clamp and lock it by
pressing on the latch.
5
Ethernet
Straight-Through
Cable
7. CONNECT TO POWER. Insert the supplied power cord’s
round end into the jack labeled POWER. Plug the
transformer into an AC outlet.
POWER
When the power cord is installed, the router goes through
a power-on self-test. LED Status on page 7 shows how
the LEDs should appear after a successful test.
POWER
Transformer
Installation is now complete.
If your Internet Service Provider (ISP) has instructed you to configure the Hotwire
ADSL/R Bridge/Router using the web interface, or if you would like to use the device as
a router, proceed to Configuring the Hotwire ADSL/R Bridge/Router on page 8.
Note to service provider: Each 6381 on the same subnet requires a unique IP address if
you wish to upgrade firmware or access it using the web interface.
6
LED Status
The Hotwire ADSL/R Bridge/Router’s front panel includes LEDs (light-emitting diodes)
that provide status on the router and its interfaces. In Table 1, Front Panel LEDs, the
Condition in BOLD shows how the LED should appear after a successful power-on
self-test.
PWR
ALM
TST
LINE
TX/RX
ETHERNET
ADSL/R
03-17357
Table 1. Front Panel LEDs
LED
Condition Status
PWR
ON
The router has power.
ALM
ON
An alarm condition exists.
OFF
No alarms have been detected by the router.
ON
A service provider-initiated test is in progress.
OFF
No tests are active.
ON
The DSL link is established.
OFF
No DSL link has been established.
Blinking
Data transmission is in progress on the DSL line.
OFF
No data is being transmitted or received by the router.
ON
The Ethernet connection is active.
OFF
No Ethernet device is detected.
TST
LINE
TX/RX
ETHERNET
7
Configuring the Hotwire ADSL/R Bridge/Router
STOP. Do not proceed with this section unless you were so instructed by your
Internet Service Provider (ISP), or you are familiar with IP and routing protocols.
Depending on the requirements of your ISP, your Hotwire ADSL/R Bridge/Router may
have a web interface that you can access using a web browser such as Internet Explorer
or Netscape. The web interface is used to configure the router.
Procedure
To configure the router using the web interface:
1. Start your web browser on a PC that is connected to the router directly or through
your hub.
2. Type the following into your web browser’s address line:
http://192.168.1.1:8080
3. Press Enter. The Login screen appears.
4. Enter the password provided to you by your ISP. (This is admin if your ISP uses the
factory default.) The Basic Setup screen appears.
5. Enter and select the parameters according to the instructions provided by your ISP.
Click on Save.
8
6. Click on Network. The Network screen appears.
7. Enter and select the parameters according to the instructions provided by your ISP.
Click on Save.
8. When you have made all changes recommended by your ISP, click on the Logout
link to end the session.
The following sections describe all the web interface screens.
Login
This is the first screen that you encounter when you type the router's IP address into the
address line of your web browser. Enter the default password provided to you by your
Internet Service Provider (ISP). This is admin if your ISP uses the factory default.
Change the password upon your first login, and keep a record of the new password.
Factory defaults must be restored to recover from a lost password, resulting in the loss
of all current settings in the router.
9
Basic Setup
This screen allows you to configure your router's server side (Wide Area Network, or
WAN) properties. Follow the instructions provided by your ISP.
Internet
The Basic Setup screen has buttons that let you select the method that your router uses
to connect to the Internet. There are five different ways that you can use to connect to
the Internet:
1. Obtain an IP address automatically. This method uses the Dynamic Host
Configuration Protocol (DHCP) to obtain the IP address from the server. The IP
address is dynamically assigned and is not known prior to assignment.
2. Specify an IP address. Use this option if your ISP has assigned a static IP address.
Enter the IP address, subnet mask, and gateway as instructed by your ISP. Up to
three Domain Name Server (DNS) addresses can also be specified. These allow
you to have access to other web servers.
3. PPPoE. PPPoE (Point to Point Protocol over Ethernet) is also known as RFC 2516.
PPP is a method of establishing a session between network hosts. It usually
provides a mechanism of authenticating users. PPPoE is a method of
encapsulating PPP packets over Ethernet.
4. PPPoA (LLC/SNAP) or
5. PPPoA (VC-MUX). PPP over ATM is also known as RFC 2364. It is a method of
encapsulating PPP packets over ATM cells which are carried over the DSL line.
LLC/SNAP and VC-MUX are two different methods of encapsulating the PPP
packet.
In order to connect using PPPoE or PPPoA, click on the appropriate radio button, fill out
the login information and other variables, and click on the Connect button. To
disconnect, click on the Disconnect button.
Connect on Demand: If this option is checked, then the connection remains dormant
until traffic flows through the link. If the Connect on Demand feature is checked, and the
modulation chosen is PPPoE or PPPoA:
In order to initiate a PPP connection on demand, access a remote website with your
browser. When traffic is detected over the link, the connection is activated.
When the Disconnect button is clicked to stop the PPP connection, Internet access
is disabled until the Connect button is clicked. No subsequent browser requests are
acted upon until the Connect button is clicked or the Connect on Demand option is
unchecked.
Idle Timeout: This is the duration of time (in minutes) after which the PPP connection
times out due to lack of activity.
10
DSL
VPI and VCI: These need to be filled in for the router to be able to communicate with
your Central Office (CO) via DSL. VPI (Virtual Path Identifier) and VCI (Virtual Circuit
Identifier) identify the route that the ATM cells take to reach the CO.
Modulation: This specifies the DSL modulation: Multi-Mode, T1.413, G.DMT (G.992.1),
or G.LITE (G.992.2). In Multi-Mode, the router automatically detects the modulation.
To save the settings, click on Save. If you have made a mistake, you can click on Reset
to start over.
Advanced Setup – Network
The Network screen allows you to configure your router's client side (Local Area
Network, or LAN) properties. This allows you to modify the router's LAN IP address and
the method of routing to use. Apply changes with care, since they could affect other
clients connected to the router.
LAN IP Address and Network Mask: These fields set the IP address and mask of the
router on the client side. These are the connection parameters that your PC uses to
communicate with the router.
Host Name: Some ISPs require your router to be uniquely identified by a host name.
DHCP server: Click on Enable if you want your router to run a DHCP server to
dynamically assign IP addresses to client machines.
IP Range: Specifies the range of IP addresses that the router may assign to clients
requesting an IP address.
Lease Time: Duration (in hours) for which the assigned IP address remains valid When
the IP address expires, the client must renew it.
Routing without NAT: This method requires each client connected to the router to have
a True IP address. The router maps this IP uniquely with a client and routes traffic
appropriately.
Routing with NAT: This method supports both True and Virtual IP addresses for clients.
The router maintains a table of virtual IP addresses and port numbers. The combination
of these two uniquely identifies each client.
Bridging: Selecting this method causes the router to function as a simple bridge with no
routing functionality.
11
Advanced Setup – Miscellaneous
The Miscellaneous Setup screen allows you to change the web login password, set up a
firewall, restart the router, and restore factory defaults.
Web Login
This feature allows you to change your basic router password. It is recommended that
you change the default password after the first time you log in and that you change it
periodically.
Web Timeout. This is the duration in minutes for which your session remains active.
Once your session expires, the Login screen appears and you are required to enter your
password again. Click on Change once you are done entering all the information.
Firewall
DMZ Support: Click in the Enable box to enable DMZ support. NOTE: When you enable
DMZ support, Telnet traffic is sent to the DMZ host. Your current Telnet session is lost
when you click on Save.
IP Address of DMZ Host: The DMZ host is the client machine that is assigned to
receive any unmapped traffic.
Discard Ping from WAN Side: Click in the Enable box to force all pings from the server
side to any client side machine to be ignored by the router.
Remote Access of Configuration: Click in the Enable box to permit configuration of
the router by a remote machine.
Remote Telnet: Click in the Enable box to permit a remote machine to telnet into the
router using its IP address.
Enable SPI Protection: Click in the Enable box to enable Stateful Packet Inspection
(SPI), which intercepts packets at the network layer and analyzes data derived from all
communication layers. It can incorporate communication and application specific
context data which can be stored and updated dynamically.
Click on Save to apply the firewall configuration for your router.
Miscellaneous Items
Restart Router: Clicking on this button causes the router to reboot. All previously saved
configuration settings are applied.
Restore Factory Defaults: Clicking on this button restores all factory default settings.
Any changes that you may have applied are permanently lost.
12
Advanced Setup – Virtual Servers
The Virtual Servers screen allows you to enable and configure your virtual servers. In
common networks, there is often a need to organize servers based on the specific
functions they need to serve. For instance, you may need to have a Domain Name
Server, Web Server, and a Mail Server, each of them uniquely identified by its IP
address. These well known servers need to be configured so that they can be externally
accessed.
To configure a virtual server, specify the IP address and click in its associated Enable
box. Unless the Enable field is checked, your IP settings are ignored. Click on Save to
save the settings.
NOTE: If you define a Telnet virtual server, your current Telnet session is lost when you
click on Save.
Advanced Setup – Custom Virtual Servers
This screen is an extension to the Virtual Server screen and can be used to configure
non-standard servers. You need to know the protocol that needs to be used in order to
access these servers, and also their LAN side and WAN side port numbers. The Range
field is used to specify the number of ports used by the custom server. Unless the
Enable box is checked, all the settings are ignored. Click on Save to save the settings.
Status – Router Status
The Router Status screen gives you basic information about the router, including WAN
and LAN IP settings, MAC addresses, routing mode, and DHCP settings. This screen
can be used as a means of verifying your current settings and to check if all the
configuration changes you made were applied successfully.
Status – DSL Status
The DSL Status screen gives you the status of your broadband (DSL) connection. It also
serves as a way to verify your current settings.
Modem Status: This field tells you whether you are connected or not.
Connection Rates: TX (upstream) and RX (downstream) data rates are displayed in
kbps.
VPI and VCI: These are the Virtual Circuit parameters used to connect to the Central
Office.
Protocol: This is the protocol used to connect to the Central Office.
Modulation: This field specifies the modulation standard used in your DSL connection.
Advanced DSL Status: Click on the Advanced DSL Status link to obtain detailed status
information, including payload rates and ATM statistics.
13
Status – Versions
This screen supplies identification and revision information for your router and its
firmware.
Logout
The Logout link ends your web interface session and displays the login screen. The
Login screen is also displayed after a specified idle timeout value value that can be
configured from the Basic Setup screen.
14
!
Important Safety Instructions
1. Read and follow all warning notices and instructions marked on the product or included in the manual.
2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product
and to protect it from overheating, these slots and openings must not be blocked or covered.
3. Do not allow anything to rest on the power cord and do not locate the product where persons will walk on
the power cord.
4. Do not attempt to service this product yourself, as opening or removing covers may expose you to
dangerous high voltage points or other risks. Refer all servicing to qualified service personnel.
5. General purpose cables are used with this product for connection to the network. Special cables, which may
be required by the regulatory inspection authority for the installation site, are the responsibility of the
customer. Use a UL Listed, CSA certified, minimum No. 24 AWG line cord for connection to the Digital
Subscriber Line (DSL) network.
6. When installed in the final configuration, the product must comply with the applicable Safety Standards and
regulatory requirements of the country in which it is installed. If necessary, consult with the appropriate
regulatory agencies and inspection authorities to ensure compliance.
7. A rare phenomenon can create a voltage potential between the earth grounds of two or more buildings. If
products installed in separate buildings are interconnected, the voltage potential may cause a hazardous
condition. Consult a qualified electrical consultant to determine whether or not this phenomenon exists and,
if necessary, implement corrective action prior to interconnecting the products.
8. Input power to this product must be provided by one of the following: (1) a UL Listed/CSA certified power
source with a Class 2 or Limited Power Source (LPS) output for use in North America, or (2) a certified
transformer, with a Safety Extra Low Voltage (SELV) output having a maximum of 240 VA available, for use
in the country of installation.
9. In addition, since the equipment is to be used with telecommunications circuits, take the following
precautions:
—
Never install telephone wiring during a lightning storm.
—
Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
—
Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
—
Use caution when installing or modifying telephone lines.
—
Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a
remote risk of electric shock from lightning.
—
Do not use the telephone to report a gas leak in the vicinity of the leak.
15
CE Marking
→
When the product is marked with the CE mark on the equipment label, a supporting Declaration of Conformity
may be downloaded from the Paradyne World Wide Web site at www.paradyne.com. Select Support
CE Declarations of Conformity.
Technical Manuals
→
! CANADA – EMI NOTICE:
This Class B digital apparatus meets all requirements of the Canadian interference-causing
equipment regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du règlement sur le matérial
brouilleur du Canada.
Japan – Notices
This is a Class B product based on the standard of the Voluntary Control Council for
Interference from Information Technology Equipment (VCCI). If this is used near a radio or
television receiver in a domestic environment, it may cause radio interference. Install and use
the equipment according to the instruction manual.
16
Declaration of Conformity
This Declaration of Conformity is made by Paradyne Corporation pursuant to Parts 2 and 15 of the Federal
Communications Commission’s Rules. This compliance information statement pertains to the following products:
Trade Name:
Model Number:
Hotwire
6381-Ax-2xx
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
The name, address, and telephone number of the responsible party is given below:
Paradyne Corporation
8545 126th Avenue North
Largo, FL 33773-1502
Phone: (727) 530-2000
The authority to operate this equipment is conditioned by the requirement that no modifications will be made to
the equipment unless the changes or modifications are expressly approved by Paradyne Corporation. The
supplied ferrite clamps must be installed as instructed to ensure compliance with Part 15, FCC Rules.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Supplier’s Declaration of Conformity
Place of Issue:
Paradyne Corporation
8545 126th Avenue North
Largo, FL 33773-1502
USA
Date of Issue:
02/26/2003
Paradyne Corporation, located at the above address, hereby certifies that the Hotwire® ADSL/R Bridge/Router
Model Number 6381-AX-210, bearing labeling identification number US:AW2DL03B6381-AX complies with: the
Federal Communications Commission's ("FCC") Rules and Regulations 47 CFR Part 68, the Administrative
Council on Terminal Attachments ("ACTA")-adopted technical criteria TIA-968-A, "Telecommunications Telephone Terminal Equipment -Technical Requirements for Connection of Terminal Equipment To the Telephone
Network, October 2002."
Patrick Murphy
Senior Vice President, Chief Financial Officer
17
Notice to Users of the United States Telephone Network
The following notice applies to versions of the Hotwire ADSL/R Bridge/Router, Model 6381, that have been FCC
Part 68 approved.
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the Administrative
Council for Terminal Attachment (ACTA). On the bottom side of this equipment is a label that contains, among
other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be
provided to the Telephone Company.
This equipment is intended to connect to the Public Switched Telephone Network through a Universal Service
Order Code (USOC) type RJ11C or RJ14C jack. A plug and jack used to connect this equipment to the premises
wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by
the ACTA. A compliant telephone cord and modular plug is provided with this product. It has been designed to be
connected to a compatible modular jack that is also compliant.
The Ringer Equivalence Number (or REN) is used to determine the number of devices that may be connected to
a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an
incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the
number of devices that may be connected to a line, as determined by the total RENs, contact the local Telephone
Company. The REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX.
The digits represented by ## are the REN without a decimal point. For example, 03 represents a REN of 0.3.
If the ADSL/R Bridge/Router causes harm to the telephone network, the Telephone Company will notify you in
advance that temporary discontinuance of service may be required. But if advance notice is not practical, the
Telephone Company will notify the customer as soon as possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it is necessary.
The Telephone Company may make changes in its facilities, equipment, operations or procedures that could
affect the operation of the equipment. If this happens, the Telephone Company will provide advance notice in
order for you to make necessary modifications to maintain uninterrupted service.
If trouble is experienced with the ADSL/R Bridge/Router, refer to the repair and warranty information in this
document.
If the equipment is causing harm to the telephone network, the Telephone Company may request that you
disconnect the equipment until the problem is resolved.
The user may make no repairs to the equipment.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public
service commission or corporation commission for information.
If the site has specially wired alarm equipment connected to the telephone line, ensure the installation of the
ADSL/R Bridge/Router does not disable the alarm equipment. If you have questions about what will disable
alarm equipment, consult your Telephone Company or a qualified installer.
Notice to Users of the Canadian Telephone Network
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications.
This is confirmed by the registration number. The abbreviation IC before the registration number signifies that
registration was performed based on a Declaration of Conformity indicating that Industry Canada technical
specifications were met. It does not imply that Industry Canada approved the equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is labeled on the equipment. The
REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to
be connected to a telephone interface. The termination on an interface may consist of any combination of devices
subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not
exceed five.
If your equipment is in need of repair, contact your local sales representative, service representative, or distributor
directly.
Trademarks
Hotwire is a registered trademark of Paradyne Corporation. ReachDSL is a trademark of Paradyne Corporation.
All other products and services mentioned herein are the trademarks, service marks, registered trademarks, or
registered service marks of their respective owners.
18
License Agreement
ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS TERMS, YOU MAY USE THE
SOFTWARE AND/OR FIRMWARE INCORPORATED INTO THE PARADYNE PRODUCT. BY USING THE
PARADYNE PRODUCT YOU SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.
IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS LICENSE AGREEMENT,
PROMPTLY RETURN THE UNUSED PRODUCT IN ITS ORIGINAL PACKAGING AND YOUR SALES RECEIPT
OR INVOICE TO THE LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE LOCATION
FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU WILL RECEIVE A REFUND OR
CREDIT FOR THE PARADYNE PRODUCT PURCHASED BY YOU.
The terms and conditions of this License Agreement (the “Agreement”) will apply to the software and/or firmware
(individually or collectively the “Software”) incorporated into the Paradyne product (the “Product”) purchased by
you and any derivatives obtained from the Software, including any copy of either. If you have executed a separate
written agreement covering the Software supplied to you under this purchase, such separate written agreement
shall govern.
Paradyne Corporation (“Paradyne”) grants to you, and you (“Licensee”) agree to accept a personal,
non-transferable, non-exclusive, right (without the right to sublicense) to use the Software, solely as it is intended
and solely as incorporated in the Product purchased from Paradyne or its authorized distributor or reseller under
the following terms and conditions:
1. Ownership: The Software is the sole property of Paradyne and/or its licensors. The Licensee acquires no
title, right or interest in the Software other than the license granted under this Agreement.
2. Licensee shall not use the Software in any country other than the country in which the Product was rightfully
purchased except upon prior written notice to Paradyne and an agreement in writing to additional terms.
3. The Licensee shall not reverse engineer, decompile or disassemble the Software in whole or in part.
4. The Licensee shall not copy the Software except for a single archival copy.
5. Except for the Product warranty contained in the manual, the Software is provided “AS IS” and in its present
state and condition and Paradyne makes no other warranty whatsoever with respect to the Product
purchased by you. THIS AGREEMENT EXPRESSLY EXCLUDES ALL OTHER WARRANTIES, WHETHER
EXPRESS OR IMPLIED, OR ORAL OR WRITTEN, INCLUDING WITHOUT LIMITATION:
a.
Any warranty that the Software is error-free, will operate uninterrupted in your operating environment,
or is compatible with any equipment or software configurations; and
b.
ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
NON-INFRINGEMENT.
Some states or other jurisdictions do not allow the exclusion of implied warranties on limitations on how long
an implied warranty lasts, so the above limitations may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights which vary from one state or jurisdiction to another.
6. IN NO EVENT WILL PARADYNE BE LIABLE TO LICENSEE FOR ANY CONSEQUENTIAL, INCIDENTAL,
PUNITIVE OR SPECIAL DAMAGES, INCLUDING ANY LOST PROFITS OR LOST SAVINGS, LOSS OF
BUSINESS INFORMATION OR BUSINESS INTERRUPTION OR OTHER PECUNIARY LOSS ARISING
OUT OF THE USE OR INABILITY TO USE THE SOFTWARE, WHETHER BASED ON CONTRACT,
TORT, WARRANTY OR OTHER LEGAL OR EQUITABLE GROUNDS, EVEN IF PARADYNE HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY ANY THIRD PARTY.
7. The rights granted under this Agreement may not be assigned, sublicensed or otherwise transferred by the
Licensee to any third party without the prior written consent of Paradyne.
8. This Agreement and the license granted under this Agreement shall be terminated in the event of breach by
the Licensee of any provisions of this Agreement.
9. Upon such termination, the Licensee shall refrain from any further use of the Software and destroy the
original and all copies of the Software in the possession of Licensee together with all documentation and
related materials.
10. This Agreement shall be governed by the laws of the State of Florida, without regard to its provisions
concerning conflicts of laws.
19
In addition to other licensed firmware contained in this Product, the firmware also contains all or portions of the
Linux® Operating System ("Program") under the licensing control of the Free Software Foundation through which
you are given a royalty-free license to use, copy, modify and sublicense the Program under the terms of the GNU
General Public License which may be viewed at http://www.gnu.org/licenses/gpl.txt. If at any time within a threeyear period after your purchase of this product you wish receive a verbatim, machine-readable copy of the
Program's source code at Paradyne's physical cost of distributing the source code plus shipping, you may do so
by stating your request in writing to us at 8545 126th Avenue North, Largo, Florida 33712, ATTN: ADSL/R Product
Management. THE PROGRAM IS PROVIDED AS IS, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, TO INCLUDE, WITHOUT LIMITATION, THE WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE.
Notice to Service Providers
Consult any associated release notes before upgrading firmware. Both, when available,
Subscriber Firmware.
will be found at www.paradyne.com. Select Support
→
*6381-A2-GN10-10*
*6381-A2-GN10-10*
Copyright © 2003 Paradyne Corporation. Printed in U.S.A.
20