3. Installation and Initial Startup
Line Interactive Sinewave UPS
Quick Guide V. 1.2
NOTE: Before installation, please inspect the unit. Be sure that nothing inside
the package is damaged.
1. Product Overview
 Input voltage
 Output voltage
 AC mode indicator
 Load level
 Overload indicator
 Battery mode indicator
 Battery level
 Low battery indicator
 Fault indicator
Front View:
LCD panel
Power switch
Back View:
Placement & Storage Conditions
Install the UPS in a protected area that is free of excessive dust and has adequate air flow.
Please place the UPS away from other units at least 20 cm to avoid interference. Do NOT
operate the UPS where the temperature and humidity is outside the specific limits. (Please
check the specs for the limitations.)
Connect to Utility and Charging
Plug in the AC input cord to the wall outlet. For the best results,
750/1K VA
suggest to charge the battery at least 6 hours before initial use.
The unit charges its battery while connecting to the utility.
Connect the Loads
6 hours
Plug in the loads to output receptacles on the rear panel of the UPS. Simply turn on the
power switch of UPS unit, then devices connected to the UPS will be protected by UPS unit.
Connect Modem/Phone/Network for Surge Protection
Schuko Type I French Type I
French Type II Schuko Type II IEC Type
Connect a single modem/phone line into surge-protected “IN” outlet on the back panel of
the UPS unit. Connect from “OUT” outlet to the computer with another phone line cable.
Connect Communication Cable
To allow for unattended UPS shutdown/start-up and status monitoring, connect the
communication cable one end to the USB/RS-232 port and the other to the communication
port of your PC. With the monitoring software installed, you can schedule UPS
NEMA Type I
NEMA Type II
UK Type Universal Type
S. Africa Type
1.5K/2K VA
shutdown/start-up and monitor UPS status through PC.
Turn On/Off the Unit
Turn on the UPS unit by pressing the power switch. Turn off the UPS unit by pressing again
the power switch.
4. Important Safety Warning (SAVE THESE INSTRUCTIONS)
Please comply with all warnings and operating instructions in this manual strictly. Save this
manual properly and read carefully the following instructions before installing the unit. Do
not operate this unit before reading through all safety information and operating instructions
carefully.
CAUTION! Please transport the UPS only in the original package to protect against shock and impact.
Schuko Type
Output receptacles

 AC input
 Circuit breaker
NEMA Type I
NEMA Type II
Modem/Phone/Network surge protection

 RS-232 com. port
 USB com. port
IEC Type
CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled
indoor area free of conductive contaminants. (See the specifications for the acceptable temperature and
humidity range.)
CAUTION! To reduce the risk of overheating the UPS, do not cover the UPS' cooling vents and avoid
exposing the unit to direct sunlight or installing the unit near heat emitting appliances such as space
heaters or furnaces.
CAUTION! Do not attach non-computer-related items, such as medical equipment, life-support
equipment, microwave ovens, or vacuum cleaners to UPS.
CAUTION! Do not plug the UPS input into its own output.
CAUTION! Condensation may occur if the UPS system is moved directly from cold to warm environment.
The UPS must be absolutely dry before being installed.
CAUTION! Place cables in such a way that no one can step on or trip over them.
CAUTION! The mains socket outlet that supplies the UPS shall be installed near the UPS and shall be
easily accessible. The UPS power cord must be connected to an earthed mains socket outlet for safety
reasons.
CAUTION! Do not allow liquids or any foreign object to enter the UPS. Do not place beverages or any
other liquid-containing vessels on or near the unit.
CAUTION! In the event of an emergency, press the OFF button and disconnect the power cord from the
AC power supply to properly disable the UPS.
CAUTION! Do not attach a power strip or surge suppressor to the UPS.
CAUTION! If the UPS is with metal chassis, for safety purpose, grounding is a must during UPS installation
in order to reduce leakage current below 3.5mA.
Attention hazardous through electric shock. Also with disconnection of this unit from the mains,
hazardous voltage still may be accessible through supply from battery. The battery supply should be
therefore disconnected in the plus and minus pole at the quick connectors of the battery when
maintenance or service work inside the UPS is necessary.
CAUTION! Servicing of batteries should be performed or supervised by personnel knowledgeable of
batteries and the required precautions. Keep unauthorized personnel away from batteries.
CAUTION! When replacing the batteries, use the same number and type of batteries.
CAUTION! Avoid touching eyes while working near batteries.
CAUTION! Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing, or
eyes.
CAUTION! Do not disassemble the unit before contact with the qualified service center when service or
repair is required.
CAUTION! To reduce risk of injury, only use qualified batteries from qualified distributors or
manufacturers. Any unqualified batteries may cause damage and injury. Do NOT use old or overdue
batteries. Please check the battery type and date code before installation to avoid damage and injury.
CAUTION! Internal battery voltage is 12VDC. Sealed, lead-acid, 6-cell battery.
CAUTION! Do not dispose of batteries in a fire. The battery may explode. Do not open or mutilate the
battery or batteries. Released electrolyte is harmful to the skin and eyes.
CAUTION! Unplug the UPS prior to cleaning and do not use liquid or spray detergent.
CAUTION! A battery can present a risk of electric shock and high short circuit current. The following
precaution should be observed before replacing batteries:
1)
Remove watches, rings, or other metal objects.
2)
Use tools with insulated handles.
3)
Wear rubber gloves and boots.
4)
Do not lay tools or metal parts on top of batteries.
5)
Disconnect charging source prior to connecting or disconnecting batteries terminal.
5. Software Download & Installation (Only for the model with
communication port)
Please follow steps below to download and install monitoring software:
1. Go to the website http://www.power-software-download.com
2. Click ViewPower software icon and then choose your required OS to download the software.
3. Follow the on-screen instructions to install the software.
4. When your computer restarts, the monitoring software will appear as an orange plug icon
located in the system tray, near the clock.
6. Trouble Shooting
Use the table below to solve minor problems.
Problem
Possible Cause
Solutions
No words display on the AC input is not connected Check if the input power cord is firmly
front panel even though well.
connected to the mains.
the mains is normal.
AC input is connected to the Plug AC input power cord to AC input
UPS output.
correctly.
Battery backup time is
Batteries are not fully
Charge the batteries at least 6 hours
shorter than nominal
charged.
and then check the capacity again.
value.
If the problem still persists, please
consult your dealer.
Batteries defect.
Contact your dealer to replace the
batteries.
Warning or fault icon is Fan is locked or not working. Check fans and notify your dealer.
shown and alarm is
The UPS is overload.
Remove some loads first. Before
continuously sounding.
reconnecting devices, please verify the
total loads match the UPS capability
specified in the spec.
Low battery icon is shown Low battery.
Charge the UPS at least 6 hours.
on the LCD screen.
7 Specifications
Model
CAPACITY
INPUT
Voltage
Voltage Range
OUTPUT
Voltage Regulation
Transfer Time
Waveform
BATTERY
Type & Number
Charging Time
PHYSICAL
Dimension (DxWxH)
Net Weight (kgs)
Environment
Humidity
Noise Level
MANAGEMENT
USB/RS-232 (option)
750
1K
1.5K
2K
750VA/480W
1000VA/700W
1500VA/1050W
2000VA/1400W
110/120 VAC or 220/230/240 VAC
81-145 VAC / 162-290 VAC
+/-10%
Typical 2-6 ms, 10 ms max.
Pure Sine Wave
12V/9Ah x 1
12V/7Ah x 2
12V/9Ah x 2
4-6 hours recover to 90% capacity
350 x 146 x 160 mm
6.8
8.96
12V/10Ah x 2
397 x 146 x 205 mm
12.18
13.7
0-90 % RH @ 0-40°C (non-condensing)
Less than 45 dB
Less than 55 dB
Supports Windows® 2000/2003/XP/Vista/2008/7/8, Linux, Unix, and
MAC