P-3521DN
Advanced Operation Guide
Contents
1
Paper Handling ........................................................................... 1-1
General Guidelines ..................................................................... 1-2
Selecting the Right Paper .......................................................... 1-4
Paper Type ................................................................................ 1-11
2
Using the Operation Panel ......................................................... 2-1
General Information ................................................................... 2-2
Understanding the Operation Panel ......................................... 2-3
Using the Menu Selection System ............................................ 2-8
Setting a Mode Selection Menu ............................................... 2-10
Report Print ............................................................................... 2-11
USB Memory (USB memory selection) ................................... 2-16
Counter (Viewing the counter value) ...................................... 2-18
Paper Settings .......................................................................... 2-19
Print Settings ............................................................................ 2-26
Network (Network settings) ..................................................... 2-41
Optional Network (Optional Network settings) ...................... 2-50
Device Common (Selecting/Setting the common device) .... 2-55
Security ..................................................................................... 2-73
Administrator (Administrator settings) .................................. 2-81
3
Option .......................................................................................... 3-1
General Information ................................................................... 3-2
Expansion Memory Modules ..................................................... 3-3
Paper Feeder (PF-100) ................................................................ 3-5
Network Interface Kit (IB-50) ..................................................... 3-5
Wireless Network Interface Kit (IB-51) ...................................... 3-5
USB Flash Memory ..................................................................... 3-5
4
Computer Interface ..................................................................... 4-1
General Information ................................................................... 4-2
USB Interface .............................................................................. 4-2
Network Interface ....................................................................... 4-3
Glossary ..................................................................................... 5-1
Index .................................................................................... Index-1
i
1-ii
Introduction
Regarding Tradenames
• KPDL is a trademark of Kyocera Corporation.
• Microsoft, Windows, Windows XP, Windows Server 2003, Windows
Vista, Windows Server 2008, Windows 7, Windows Server 2012,
Windows 8 and Internet Explorer are registered trademarks or
trademarks of Microsoft Corporation in the U.S.A. and/or other
countries.
• PCL is a trademark of Hewlett-Packard Company.
• Adobe Acrobat, Adobe Reader and PostScript are trademarks of
Adobe Systems, Incorporated.
• Ethernet is a registered trademark of Xerox Corporation.
• NetWare is a registered trademark of Novell, Inc.
• IBM is a registered trademark of International Business Machines
Corporation.
• AppleTalk, Bonjour, Macintosh, and Mac OS are trademarks of Apple
Inc., registered in the U.S. and other countries.
• All European language fonts installed in this machine are used under
licensing agreement with Monotype Imaging Inc.
• Helvetica, Palatino and Times are registered trademarks of Linotype
GmbH.
• ITC Avant Garde Gothic, ITC Bookman, ITC ZapfChancery and ITC
ZapfDingbats are registered trademarks of International Typeface
Corporation.
• UFST™ MicroType® fonts by Monotype Imaging Inc. are installed in
this machine.
• AirPrint and the AirPrint logo are trademarks of Apple Inc.
• iOS is a trademark or registered trademark of Cisco in the U.S. and
other countries and is used under license by Apple Inc.
All other brands and product names are registered trademarks or
trademarks of their respective companies. Thedesignations ™ and ® will
not be used in this Operation Guide.
iii
About the Advanced Operation Guide
This guide has the following chapters:
1 Paper Handling
This chapter explains how choose, handle and load paper.
2
Using the Operation Panel
This chapter explains how to use the operation panel to configure the
printer.
3
Option
This chapter explains the options for this printer.
4
Computer Interface
This chapter explains the possible connections between the printer and
your computer.
Glossary
A Glossary of terms used is provided here.
iv
Conventions in This Guide
This manual uses the following conventions.
Convention
Description
Italic
Typeface
Used to emphasize a key word, Refer to Configuration Tool on page 3-9.
phrase or reference to additional
information.
Used to denote buttons on the
To start printing, click OK.
software.
Bold
Example
Bracket Bold Used to denote operation panel Printing resumes when [GO] is
keys.
pressed.
Note
Used to provide additional or
useful information about a
function or feature.
Important
Used to provide important
information.
Caution
Cautions are statements that
CAUTION When pulling the paper, pull
suggest mechanical damage as it gently so as not to tear it. Torn pieces
a result of an action.
of paper are difficult to remove and may
Note Do not remove the toner
container from the carton until you
are ready to install it in the printer.
IMPORTANT Take care not to touch
the transfer roller (black) during
cleaning.
be easily overlooked, deterring the
paper jam recovery.
Warning
Used to alert users to the
possibility of personal injury.
WARNING If you ship the printer,
remove and pack the developer unit
and drum unit in a plastic bag and ship
them separately from the printer.
v
vi
1
Paper Handling
This chapter explains paper specifications for this printer.
General Guidelines
Selecting the Right Paper
Paper Type
Paper Handling
1-2
1-4
1-11
1-1
General Guidelines
The machine is designed to print on standard copier paper, but it can
also accept a variety of other types of paper within the limits specified
below.
Note The manufacturer assumes no liability for problems that
occur when paper not satisfying these requirements is used.
Selection of the right paper is important. Using the wrong paper can
result in paper jams, curling, poor print quality, and paper waste, and in
extreme cases can damage the machine. The guidelines given below
will increase the productivity of your office by ensuring efficient, troublefree printing and reducing wear and tear on the machine.
Paper Availability
Most types of paper are compatible with a variety of machines. Paper
intended for xerographic copiers can also be used with the machine.
There are three general grades of paper: economy, standard, and
premium. The most significant difference between grades is the ease
with which they pass through the machine. This is affected by the
smoothness, size, and moisture content of the paper, and the way in
which the paper is cut. The higher the grade of paper you use, the less
risk there will be of paper jams and other problems, and the higher the
level of quality your printed output will reflect.
Differences between paper from different suppliers can also affect the
machine's performance. A high-quality printer cannot produce highquality results when the wrong paper is used. Low-priced paper is not
economical in the long run if it causes printing problems.
Paper in each grade is available in a range of basis weights (defined
later). The traditional standard weights are 60 to 120 g/m2 (16 to 31.9b).
Paper Specifications
The following table summarizes the basic paper specifications. Details
are given on the following pages:
Item
Specifications
Weight
Cassette: 60 to 120 g/m² (16 to 31.9 lb/ream)
MP tray: 60 to 220 g/m² (16 to 58.5 lb/ream)
0.086 to 0.110mm (3.4 to 4.3 mils)
±0.7 mm (±0.0276 inches)
Thickness
Dimensional
Accuracy
Squareness of
Corners
Moisture Content
Direction of Grain
Pulp Content
1-2
90±0.2°
4 to 6%
Long grain
80% or more
Paper Handling
Minimum and Maximum Paper Sizes
The minimum and maximum paper sizes are as follows. For the paper
smaller than JIS B6, postcards, and envelopes, the MP tray must be
used.
105mm
(4-1/8 inches)
Maximum
Paper Size
216mm (8-1/2 inches)
356mm (14 inches)
148mm (5-13/16 inches)
356mm (14 inches)
Minimum
Paper Size
148mm (5-13/16 inches)
MP tray
Paper cassette
Minimum
Paper Size
70mm
(2-3/4 inches)
Maximum
Paper Size
216mm (8-1/2 inches)
Note The minimum paper size of the optional paper feeder (PF100) is 148 x 210 mm (5-13/16 x 8-5/16 inches).
Paper Handling
1-3
Selecting the Right Paper
This section describes the guidelines for selecting paper.
Condition
Avoid using paper that is bent at the edges, curled, dirty, torn,
embossed, or contaminated with lint, clay, or paper shreds.
Use of paper in these conditions can lead to illegible printing and paper
jams, and can shorten the life of the machine. In particular, avoid using
paper with a surface coating or other surface treatment. Paper should
have as smooth and even a surface as possible.
Composition
Do not use paper that has been surface-treated and contains plastic or
carbon. The heat of fusing can cause such paper to give off harmful
fumes.
Bond paper should contain at least 80% pulp. Not more than 20% of the
total paper content should consist of cotton or other fibers.
Paper Sizes
Cassettes and the MP Tray are available for the paper sizes shown
below. The dimensional tolerances are ±0.7mm for the length and width.
The angle at the corners must be 90° ±0.2°.
Cassette or
MP Tray
MP Tray Only
Size
Size
Env. Monarch
3-7/8 × 7-1/2 inches Legal
8-1/2 × 14 inches
Envelope #10
4-1/8 × 9-1/2 inches Letter
8-1/2 × 11 inches
Envelope #9
3-7/8 × 8-7/8 inches ISO A4
210 × 297 mm
Envelope #6
3-5/8 × 6-1/2 inches ISO A5
148 × 210 mm
Envelope DL
110 × 220 mm
ISO A6
105 × 148 mm
JIS B6
128 × 182 mm
Envelope C5
162 × 229 mm
Hagaki
100 × 148 mm
ISO B5
176 × 250 mm
OufukuHagaki
148 × 200 mm
JIS B5
182 × 257 mm
Youkei 2
114 × 162 mm
Statement
5-1/2 × 8-1/2 inches
Youkei 4
105 × 235 mm
Executive
7-1/4 × 10-1/2 inches
Oficio II
8-1/2 × 13 inches
Folio
210 × 330 mm
16 kai
197 × 273 mm
216 × 340 mm 216 × 340 mm
Custom
1-4
Cassette: 105 to 216 mm × 148 to 356 mm
(4-1/8 to 8-1/2 inches × 5-13/16 to 14 inches)
MP Tray: 70 to 216 mm × 148 to 356 mm
(2-3/4 to 8-1/2 inches × 5-13/16 to 14 inches)
Paper Handling
Smoothness
The paper should have a smooth, uncoated surface. Paper with a rough
or sandy surface can cause blank spaces in the printed output. Paper
that is too smooth can cause multiple feeding and fogging problems.
(Fogging is a gray background effect.)
Basis Weight
Basis weight is the weight of paper expressed in grams per square meter
(g/m²). Paper that is too heavy or too light may cause feed errors or
paper jams as well as premature wear of the product. Uneven weight of
paper, namely uneven paper thickness may cause multiple-sheet
feeding or print quality problems such as blurring because of poor toner
fusing.
Paper Weight Equivalence Table
The paper weight is listed in pounds (lb) and metric grams per square
meter (g/m²). The shaded part indicates the standard weight.
U. S. Bond Weight (lb)
Europe Metric Weight (g/m²)
16
60
17
64
20
75
21
80
22
81
24
90
27
100
28
105
32
120
34
128
36
135
39
148
42
157
43
163
47
176
53
199
Thickness
The paper used with the machine should be neither extremely thick nor
extremely thin. If you are having problems with paper jams, multiple
feeds, and faint printing, the paper you are using may be too thin. If you
are having problems with paper jams and blurred printing the paper may
be too thick.
Paper Handling
1-5
Moisture Content
Moisture content is defined as the percent ratio of moisture to the dry
mass of the paper. Moisture can affect the paper’s appearance, feed
ability, curl, electrostatic properties, and toner fusing characteristics.
The moisture content of the paper varies with the relative humidity in the
room. When the relative humidity is high and the paper absorbs
moisture, the paper edges expand, becoming wavy in appearance.
When the relative humidity is low and the paper loses moisture, the
edges shrink and tighten, and print contrast may suffer.
Wavy or tight edges can cause jams and alignment anomalies. The
moisture content of the paper should be 4 to 6%.
To ensure correct moisture content, it is important to store the paper in a
controlled environment. Some tips on moisture control are:
•
•
•
•
•
Store paper in a cool, dry location.
Keep the paper in its wrapping as long as possible. Re-wrap paper
that is not in use.
Store paper in its original carton. Place a pallet etc. under the carton
to separate it from the floor.
After removing paper from storage, let it stand in the same room as
the machine for 48 hours before use.
Avoid leaving paper where it is exposed to heat, sunlight, or damp.
Paper Grain
When paper is manufactured, it is cut into sheets with the grain running
parallel to the length (long grain) or parallel to the width (short grain).
Short grain paper can cause feeding problems in the machine. All paper
used in the machine should be long grain.
Other Paper Properties
Porosity: Indicates the density of paper fiber.
Stiffness: Limp paper may buckle in the machine, resulting in paper
jams.
Curl: Most paper naturally tends to curl one way if left unpacked. When
paper passes through the fixing unit, it curls upward a little. To produce
flat printouts, load the paper so that the upward pressure from the
machine can correct their curling.
Electrostatic discharge: During the printing process the paper is
electrostatically charged to attract the toner. The paper must be able to
release this charge so that printed sheets do not cling together in the
Output Tray.
Whiteness: The contrast of the printed page depends on the whiteness
of the paper. Whiter paper provides a sharper, brighter appearance.
Quality control: Uneven sheet size, corners that are not square, ragged
edges, welded (uncut) sheets, and crushed edges and corners can
cause the machine to malfunction in various ways. A quality paper
supplier should take considerable care to ensure that these problems do
not occur.
Packaging: Paper should be packed in a sturdy carton to protect it from
damage during transport. Quality paper obtained from a reputable
supplier is usually correctly packaged.
1-6
Paper Handling
Special Paper
The following types of special paper can be used:
Paper type to be used
Paper type to be selected
Thin paper (60 to 64 g/m²)
Thick paper (90 to 220 g/m²)
Colored paper
Recycled paper
Overhead projector transparencies
Cardstock
Envelopes
Label
Vellum
Thick
Color
Recycled
Transparency
Cardstock
Envelope
Labels
Use paper that is sold specifically for use with copiers or printers (heatfusing type). When using transparencies, labels, envelopes, cardstock,
or thick paper, feed the paper from the MP Tray.
Since the composition and quality of special paper vary considerably,
special paper is more likely than white bond paper to give trouble during
printing. No liability will be assumed if moisture and so forth given off
during printing on special paper causes harm to the machine or operator.
Note Before purchasing any type of special paper, test a sample
on the machine and check that printing quality is satisfactory.
Half speed mode is automatically engaged depending on Media
types, including Labels, Rough, and Thick.
Transparency
This printer is available for monochrome printing on transparencies.
Transparencies must be fed to the MP Tray. One transparency can be
loaded at a time.
Transparencies must be able to withstand the heat of fusing during the
printing process.
Transparencies must be placed on the MP tray with the long edge
towards the printer.
When unloading transparencies (e.g., for clearing jams), hold them
carefully by the edges to avoid leaving fingerprints on them.
Labels
Labels must be fed to the MP tray. One label can be loaded at a time.
The basic rule for printing on adhesive labels is that the adhesive must
never come into contact with any part of the machine. Adhesive paper
sticking to the drum or rollers will damage the machine.
Paper Handling
1-7
Label paper has a structure
comprising of three layers, as
shown in the diagram. The top
Top sheet (white
sheet is printed on. The
bond paper)
adhesive layer consists of
Adhesive
pressure-sensitive adhesives.
The carrier sheet (also called
Carrier sheet
the linear or backing sheet)
holds the labels until used.
Due to the complexity of its
composition, adhesivebacked label paper is particularly likely to give printing problems.
Adhesive label paper must be entirely covered by its top sheet, with no
spaces between the individual labels. Labels with spaces in between are
liable to peel off, causing serious paper jam problems.
Some label paper is manufactured with an extra margin of top sheet
around the edge. Do not remove the extra top sheet from the carrier
sheet until after printing is finished.
Acceptable
Unacceptable
Top sheet
Carrier sheet
The table below lists the specifications for adhesive label paper.
Item
Specification
Weight of top sheet
Composite weight
Thickness of top sheet
Composite thickness
Moisture content
44 to 74 g/m² (12 to 20 lb/ream)
104 to 151 g/m² (28 to 40 lb/ream)
0.086 to 0.107 mm (3.9 to 4.2 mils)
0.115 to 0.145 mm (4.5 to 5.7 mils)
4 to 6 % (composite)
Postcards
Up to 10 postcards can be
loaded at a time. Fan the
stack of postcards and align
the edges before loading
them in the MP tray. Make
sure the postcards you are
going to set are not curled.
Feeding curled postcards
may cause paper jams.
Some postcards have rough
edges on the back (those are created when the paper is cut). In this
case, put the postcards on a flat place and rub the edges with, for
example, a ruler to smooth them.
1-8
Paper Handling
Envelopes
Up to 5 envelopes can be loaded at a time. Envelopes should be fed in
the face-up position, right edge first.
Since the composition of an envelope is more complex than that of
ordinary paper, it is not always possible to ensure consistent printing
quality over the entire envelope surface.
Normally, envelopes have a diagonal grain direction. Refer to Paper
Grain on page 1-6. This direction can easily cause wrinkles and creases
when envelopes pass through the printer. Before purchasing envelopes,
make a test print to check whether the printer accepts the envelope.
•
•
•
•
Do not use envelopes that have an encapsulated liquid adhesive.
Avoid a long printing session for envelopes only. Extended envelope
printing can cause premature printer wear.
If jams occur, try setting less envelopes on the MP tray.
To avoid jams caused by curled envelopes, stack no more than 10
printed envelopes on the output tray.
Thick Paper
Fan the stack of paper and align the edges before loading them in the
MP tray. Some types of paper have rough edges on the back (those are
created when the paper is cut). In this case, put the paper on a flat place
and rub the edges once or twice with, for example, a ruler to smooth
them. Feeding rough edged paper may cause paper jams.
Note If the paper jams
even after you smooth it
out, load the paper in
the MP tray with the
leading edge raised up
a few millimeters as
shown in the
illustration.
Colored Paper
Colored paper should satisfy the same conditions as white bond paper.
Refer to Paper Specifications on page 1-2. In addition, the pigments
used in the paper must be able to withstand the heat of fusing during the
printing process (up to 200 °C or 392 °F).
Preprinted Paper
Preprinted paper should satisfy the same conditions as white bond
paper. Refer to Paper Specifications on page 1-2.The preprinted ink
must be able to withstand the heat of fusing during the printing process,
and must not be affected by silicone oil.
Do not use paper with any kind of surface treatment, such as the type of
paper commonly used for calendars.
Paper Handling
1-9
Recycled Paper
Select recycled paper that meets the same specifications as the white
bond paper except for whiteness. Refer to Paper Specifications on
page 1-2.
Note Before purchasing recycled paper, test a sample on the
machine and check that the printing quality is satisfactory.
1-10
Paper Handling
Paper Type
The printer is capable of printing under the optimum setting for the type
of paper being used.
Setting the paper type for the paper source from the printer’s operation
panel will cause the printer to automatically select the paper source and
print in the mode best suited to that type of paper.
A different paper type setting can be made for each paper source
including the MP tray. Not only can preset paper types be selected, but it
is also possible for you to define and select customized paper types.
Refer to Type Adjust (Creating custom paper type) on page 2-24. The
following types of paper can be used.
Paper source
Paper Type
MP tray
Paper
Cassette
Duplex path
Plain
Yes
Yes
Yes
Transparency
Yes
No
No
Preprinted
Yes
Yes
Yes
Labels
Yes
No
No
Bond
Yes
Yes
Yes
Recycled
Yes
Yes
Yes
Vellum
Yes
No
No
Rough
Yes
Yes
Yes
Letterhead
Yes
Yes
No
Color
Yes
Yes
Yes
Prepunched
Yes
Yes
Yes
Envelope
Yes
No
No
Cardstock
Yes
No
No
Thick
Yes
No
No
High quality
Yes
Yes
Yes
Custom 1 (to 8)*
Yes
Yes
Yes
Yes: Can be stored
*.
Paper Handling
No: Cannot be stored
This is a paper type defined and registered by the user. Up to
eight types of user settings may be defined. User can also enable
or disable the duplex path when using Custom. For more
information, refer to Type Adjust (Creating custom paper type) on
page 2-24.
1-11
1-12
Paper Handling
2
Using the Operation
Panel
This chapter contains explanations on the following topics:
General Information
Understanding the Operation Panel
Using the Menu Selection System
Report Print
USB Memory (USB memory selection)
Counter (Viewing the counter value)
Paper Settings
Print Settings
Network (Network settings)
Optional Network (Optional Network settings)
Device Common (Selecting/Setting the common device)
Security
Administrator (Administrator settings)
Adjust/Maintenance (Adjust/Maintenance selection/setting)
Using the Operation Panel
2-2
2-3
2-8
2-11
2-16
2-18
2-19
2-26
2-41
2-50
2-55
2-73
2-81
2-84
2-1
General Information
This chapter provides the information you need to configure the printer.
In general you need to use the operation panel only to make default
settings. You can make most changes to the printer settings using the
printer driver through the application software.
Note Changes to printer settings made using a software
application override changes made using the operation panel.
You can also access the printer's various settings from a remote
location, by using the control panel, the printer driver or other utilities
such as the Status Monitor Utility. Other printer utilities can be installed
using the DVD-ROM supplied with the printer.
The chapter describes the operation panel in detail, including its menus
and the procedures for changing various printer settings.
2-2
Using the Operation Panel
Understanding the Operation Panel
The operation panel on the top of the printer has a 2-line by 21-character
liquid crystal display (LCD), eight keys, and three indicators (LED).
Messages that appear on the display and functions of indicators and
keys are explained in this chapter.
Using the Operation Panel
2-3
Message Display
The message display on the operation panel shows:
•
•
Status information, the ten messages listed below which are
displayed during normal operation.
Error codes, when the printer requires the operator’s attention; as
explained in the Operation Guide.
Status Information
Message
Meaning
Self test
The printer is performing self-diagnostics after power-up.
Please wait
The printer is warming up and is not ready.
When the printer is switched on for the first time, this message will take several minutes.
Please wait
(Adding toner)
Toner is currently being replenished. This message may be displayed during continuous
printing of a large volume of pages which require a large amount of toner such as with
photographs, etc.
Ready
The printer is ready to print.
Processing
The printer is receiving data to print. This is also shown when the printer is reading a USB
flash memory or RAM disk.
Low Power
The printer is in Low Power Mode. The printer wakes from Low Power Mode whenever a
print job is received. The printer then warms up and goes on-line.
For details on Low Power Mode, refer to Low Power Timer (Low Power Mode timer
timeout time) on page 2-64.
Sleeping
The printer is in Auto Sleep. The printer wakes from Auto Sleep whenever a print job is
received. The printer then warms up and goes on-line.
For details on Auto Sleep, refer to Sleep Timer (Sleep timer timeout time) on page 264.
Canceling data
Jobs inside the printer are being canceled. To cancel a job, refer to Canceling a Printing
Job on page 2-6.
Error Codes
Refer to the Troubleshooting section in the Operation Guide.
2-4
Using the Operation Panel
Indicators in Message Display
Ready
Ready, Data, and Attention Indicators
The following indicators light during normal operation and whenever the
printer needs attention. Depending on the status of lighting, each
indicator has the following meaning:
Indicator
Description
Flashing. Indicates an error that you can resolve. For
details, refer to the Troubleshooting section in the
Operation Guide.
On. Indicates that the printer is ready. The printer prints the
data it receives.
Off. [Cancel] was pressed during Ready is displayed.
Data can be received but will not be printed. To resume
printing, press [Cancel] again.
Printing is canceling.
Also, indicates when paper jam occurred, toner has run
out, cover is open, and so on. For details, refer to the
Troubleshooting section in the Operation Guide.
Flashing. Indicates that a data is being received.
On. Indicates either that data received is being processed
before printing starts, or that data received is being written
to or read from a RAM disk or USB flash memory.
Flashing. Indicates that the printer is ready to print when
Please wait is displayed. Also indicates that the
corresponding paper cassette is not installed.
Indicates that the printer requires maintenance such as
adding paper, cleaning the printer, preparing the toner
container.
On. Indicates when paper jam occurred, toner has run out,
cover is open, and so on. If the message includes Press
GO, press [GO] to resume printing. For details, refer to the
Troubleshooting section in the Operation Guide.
The ID or Password entered for the Security or
Administrator function is not correct. Check the ID or
Password, and enter the correct ID or password.
Using the Operation Panel
2-5
Keys
The operation panel keys are used to configure the printer operation.
Note that certain keys have a secondary function.
GO Key
Use this key to:
•
•
Recover from certain errors.
Recover from Auto Sleep mode.
Cancel Key
This key is used to:
•
•
•
Cancel a printing job.
Stop the alarm sound.
Reset numeric values or cancel a setting procedure while using
menu system.
Canceling a Printing Job
1
While the printer displays Processing, press [Cancel].
Print Cancel? appears on the message display followed by the
job name currently in progress.
2
Press U or V to display the desired job and [OK].
Canceling data appears on the message display and printing
stops after the current page is printed.
MENU Key
[MENU] lets you enter the menu system to change the setup and
printing environment of the printer.
Pressing this key during a menu selection will terminate the selection
and return the printer to the normal operation.
2-6
Using the Operation Panel
Cursor Keys
The four cursor keys are used in the menu system to access an item or
enter numeric values. Use U and V to change menus, and Y and Z to
move to the sub menu.
The cursor key with the question mark ( ) may be pressed when the
paper jam message has appeared on the message display. A help
message will then appear to facilitate jam clearing in the location.
When Use alternative? is shown in the message display, use the U
and V key to select the paper source.
OK Key
This key is used to:
•
•
Using the Operation Panel
Finalize settings of numeric values and other selections.
Set the paper source when Use alternative? is shown in the
message display.
2-7
Using the Menu Selection System
Menu Selection System
This section explains how to use the menu selection system. [MENU] on
the operation panel allows you to use the menu to configure the printer
settings to your specific needs. Settings can be made when Ready,
Please wait or Processing is on the printer message display.
Note Settings that are received from application software and the
printer driver will take priority over settings made in the operation
panel.
Entering the Mode Selection Menu
Press [MENU] when Ready, Please wait or Processing is indicated
on the printer message display.
The mode selection menu is displayed.
2-8
Using the Operation Panel
Selecting a Menu
The mode selection menu is hierarchical. Press U or V to display the
desired menu.
Paper Settings
>
If the selected menu has a sub-menu, > is displayed after the menu.
Press Z to move to the sub-menu or Y to go back.
Indicates that there is a sub-menu
>Type Adjust
CUSTOM 1
Indicates that this is
the sub-menu
>
> is displayed before the sub-menu.
Press Z to move to another sub-menu or Y to go back.
Indicates that there is
another sub-menu
>>Paper Weight
Normal 1
>> is displayed before the second sub-menu.
Indicates that this is the second sub-menu
Setting a Menu
Select the desired menu and press [OK] to set or change the
configuration.
Press U or V to display the desired item and [OK] to finalize the value
or selections set.
Cancelling Menu Selection
If you press [MENU] when a menu is selected, the message display
returns to Ready.
Using the Operation Panel
2-9
Setting a Mode Selection Menu
This section explains the setting procedures used for each menu item in
the mode selection menu.
Report Print
>
1
While the printer displays Ready, Please wait and Processing,
press [MENU]. The mode selection menu is displayed. (For example
: Report Print)
2
Each time you press U or V, the selection changes.
• Report Print
• USB Memory
• Counter
• Paper Settings
• Print Settings
• Network
• Optional Network
• Device Common
• Security
• Administrator
• Adjust/Maintenance
The Optional Network option appears when the network interface
kit is installed.
Note If you use the mode first selected when the printer is turned
on, Report Print is displayed. For the second and subsequent
times, the last menu option you selected the previous time is
displayed.
2-10
Using the Operation Panel
Report Print
The printer prints the report. Report Print includes the following items:
• Print Menu Map
• Print Status Page
• Print Fonts List
• Print RAM Disk File List
Report Print
>
1
Press [MENU].
2
Press U or V repeatedly until Report Print > appears.
Note that menus shown in the list may vary depending on which optional
units installed in the printer.
Print Menu Map
The printer prints a full list of the menu selection system menu map.
>Print Menu Map ?
Using the Operation Panel
1
2
Press Z while Report Print > is displayed.
3
Press [OK]. A question mark (?) appears.
4
Press [OK]. The message Processing appears and the printer
prints a Menu Map.
>Print Menu Map appears. In other displays, press U or V
repeatedly until the map appears.
2-11
Menu Map Sample
Menu Map
Printer
Menu Map
Printer
FS-C5250DN
1
2
2-12
Using the Operation Panel
Print Status Page
You can check the printer's current status, including available memory
space and option settings by printing a status page.
>Print Status Page ?
1
2
Press Z while Report Print > is displayed.
3
Press [OK]. A question mark (?) appears.
4
Press [OK] again. The message Processing appears and the
printer prints a status page.
Press U or V repeatedly until >Print Status Page appears.
For a sample status page and its full description, refer to the next section
Understanding the Status Page.
Understanding the Status Page
The numbers in the following diagram refer the items explained below
the diagram. The items and values on the status page may vary
depending on the printer’s firmware version.
Status Page
Printer
1
Firmware version
2
Paper Settings
Interface Block
Group Settings
Memory
5
6
EcoPrint
Print Settings
Emulation
7
Device Common Settings
Option Status
3
Counters
8
Network
Toner Gauges
4
Using the Operation Panel
9
2-13
1
Firmware Version
This item shows the version and release date of the printer
firmware.
2
Printer Settings Information
This item shows various printer settings for hardware-related
items:
3
-
Paper Settings
-
Group Settings
-
Print Settings
-
EcoPrint
-
Device Common Settings
Installed Options
This item shows the options installed in the printer:
-
4
Paper Feeder
Network Status
This item shows the IP address, subnet mask address, and
default gateway address for the network interface card in the
printer.
5
Interface Information
This information shows the block status for items including the
USB memory slot, USB interface and option interface.
6
Memory
This item shows:
7
-
Standard memory in the printer
-
Option memory slot status in megabytes
-
Total memory in the printer
-
Current status of the RAM disk
Emulation
This item shows all available emulations of the printer. The
default setting for North America is KPDL (AUTO) emulation.
The default setting for all other regions is PCL 6 emulation. The
emulations are:
8
-
PCL 6
-
KPDL (AUTO)
-
KPDL
-
Line Printer
-
IBM Proprinter
-
EPSON LQ-850
Page Information
This item shows the page related items:
9
-
Total printed page count
-
Total page count of each paper size
Consumable Status
This item shows the approximate level of remaining toner. When
the value is 100, the toner container is full. The closer to 0, the
smaller the amount of remaining toner.
2-14
Using the Operation Panel
Print Fonts List
To help you decide in selecting a font, you can printout lists of the
internal fonts or the optional fonts.
>Print Fonts List
?
1
2
Press Z while Report Print > is displayed.
3
Press [OK]. A question mark (?) appears.
4
Press [OK] again. The message Processing appears and the
printer prints a list of fonts with a sample and font ID (number) for
each of them.
Press U or V repeatedly until >Print Fonts List appears.
Print RAM Disk File List
This allows you to print a list of the files on the RAM disk.
IMPORTANT This is displayed when RAM disk mode is enabled.
1
2
>Print RAM Disk
File List ?
Using the Operation Panel
Press Z while Report Print > is displayed.
Press U or V repeatedly until >Print RAM Disk File List
appears.
3
Press [OK]. A question mark (?) appears.
4
Press [OK] again. The message Processing appears and the
printer prints a list of files stored in a RAM disk.
2-15
USB Memory (USB memory selection)
This specifies the settings for removing the USB memory and printing
USB memory content. The USB Memory menu automatically appears
when you install the USB memory.
IMPORTANT This message is displayed only when the USB host
block is set to Unblock. For more information, please refer to I/F
Block (Interface (external device) block setting) on page 2-74
The options available in USB Memory are as follows:
• Print File (Printing a file)
Copies (Number of copies)
Paper Source (Selecting the paper feed source)
• Remove Device (Removing the USB memory)
• Print File List (Printing a list of the files on a USB memory)
USB Memory
>
1
Press [MENU].
2
Press U or V repeatedly until USB Memory > appears.
Note that menus shown in the list may vary depending on which
optional units installed in the printer.
Print File (Printing a file)
You can use this to specify printing for files in the USB memory.
/
1
2
Press Z while USB Memory > is displayed.
3
Press [OK]. A question mark (?) appears.
4
Press [OK] again. The folder or file appears.
(For example : Folder 1)
Each time you press U or V, the next folder or file appears in
succession.
/00:Folder 1
>Print File appears. In other displays, press U or V repeatedly
until the map appears.
To view lower-level folders or files, press Z.
(For example : Folder 2)
/00:Folder 1
/01:Folder 2
To view folders or files on still lower levels, press Z.
(For example : File 3)
/.../01:Folder 2
02:File 3
IMPORTANT Note also that up to 3 levels of folders or files are
displayed. It might take some time before the folder or file name
appears, depending on the size of the USB memory or the
number of files.
You can move between the folder levels by pressing U and V or Y
and Z.
/.../01:Folder 2
? 02:File 3
Copies
5
Press [OK]. A question mark (?) appears.
(For example : File 3)
6
Press [OK] again. Copies appears.
001
2-16
Using the Operation Panel
Copies (Number of copies)
Sets the number of copies printed of the specified file in USB memory.
IMPORTANT To use this feature, the RAM disk must be set to On.
Copies
1
While Copies in step 5 above is displayed, press U and V or Y and
Z to display the number of copies. (E.g.: 10)
2
Press [OK]. Paper Source and a question mark (?) appears.
010
Paper Source
? Cassette 1
Paper Source (Selecting the paper feed source)
Sets the paper used for printing the specified file in USB memory.
Paper Source
? Cassette 2
1
While Paper Source in step 2 above is displayed, press U and V
or Y and Z repeatedly until the paper source appears.
(For example : Cassette 2)
Note that menus shown in the list may vary depending on which
optional units installed in the printer.
2
Press [OK]. The message Processing appears and the printer
prints a file stored in a USB memory.
Remove Device (Removing the USB memory)
Specifies the setting for USB memory removal.
>Remove Device ?
1
2
Press Z while USB Memory > is displayed.
3
Press [OK]. A question mark (?) appears.
4
Press [OK] again. Menu display ends and the USB memory device
can be removed.
Press U or V repeatedly until >Remove Device appears.
Print File List (Printing a list of the files on a USB
memory)
This allows you to print a list of the files on a USB memory device.
>Print File List ?
Using the Operation Panel
1
2
Press Z while USB Memory > is displayed.
3
Press [OK]. A question mark (?) appears.
4
Press [OK] again. The message Processing appears and the
printer prints a list of files stored in a USB memory.
Press U or V repeatedly until >Print File List appears.
2-17
Counter (Viewing the counter value)
Displays the number of pages printed.
The options available in Counter are as follows:
• Printed Pages (Displaying the total printed pages)
Counter
>
1
Press [MENU].
2
Press U or V repeatedly until Counter > appears.
Printed Pages (Displaying the total printed pages)
This only displays the total number of pages printed. You cannot change
the displayed number.
>Printed Pages
1
Press Z while Counter > is displayed.
2
Press U or V repeatedly until >Printed Pages appears. The total
number of pages printed is displayed. (E.g.: 2000)
3
Press [MENU]. The display returns to Ready.
2000
2-18
Using the Operation Panel
Paper Settings
This sets the paper size and type for the MP tray and cassettes from
which paper is supplied.
The options available in Paper Settings are as follows:
• MP Tray Size (Setting MP tray paper size)
• MP Tray Type (Setting the MP tray paper type)
• Cassette (1 to 3) Size (Setting the cassette paper size)
• Cassette (1 to 3) Type (Setting the cassette paper type)
• Type Adjust (Creating custom paper type)
• Reset Type Adjust (Resetting the custom paper type)
Paper Settings
>
1
Press [MENU].
2
Press U or V repeatedly until Paper Settings > appears.
MP Tray Size (Setting MP tray paper size)
When you use the MP tray, you should set the MP tray size to the paper
size that is used to format the job to print. If the sizes do not match,
printing will not be performed on the correct size paper.
The default setting is Letter size for the U.S. and Canada and A4 for
other countries. For more information about the paper sizes that you can
feed from the MP tray, refer to Paper Specifications on page 1-2.
Note Feeding the paper having a paper size which does not
match the current paper size from the MP tray can cause paper
jam.
>MP Tray Size
? A4
1
2
Press Z while Paper Settings > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
Press U or V to display the desired paper size. The message display
toggles through the following paper sizes:
Press U or V repeatedly until >MP Tray Size appears.
Envelope Monarch
Envelope #10
Envelope DL
Envelope C5
Executive
Letter
Legal
A4
B5
A5
A6
B6
Envelope #9
Envelope #6
ISO B5
Custom
Hagaki
Using the Operation Panel
2-19
Oufuku Hagaki
Oficio II
216x340mm
16K
Statement
Folio
Youkei 2
Youkei 4
5
6
Press [OK].
Press [MENU]. The display returns to Ready.
MP Tray Type (Setting the MP tray paper type)
You can use this to set the paper type that can be supplied from the MP
tray. The default setting is PLAIN.
For more information about paper types that you can feed from the MP
tray, refer to Paper Specifications on page 1-2.
>MP Tray Type
? PLAIN
1
2
Press Z while Paper Settings > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
Press U or V to display the desired paper type. The message display
toggles through the following paper types:
Press U or V repeatedly until >MP Tray Type appears.
PLAIN
TRANSPARENCY
PREPRINTED
LABELS
BOND
RECYCLED
VELLUM
ROUGH
LETTERHEAD
COLOR
PREPUNCHED
ENVELOPE
CARDSTOCK
THICK
HIGH QUALITY
CUSTOM 1 (to 8)
Note You can define any paper type and store that definition
in the printer. For more information, refer to Type Adjust
(Creating custom paper type) on page 2-24.
5
6
2-20
Press [OK].
Press [MENU]. The display returns to Ready.
Using the Operation Panel
Cassette (1 to 3) Size (Setting the cassette paper size)
To set the size for the paper cassette, load the paper into a paper
cassette, adjust the paper size, and select the paper size from the
operation panel.
If the PF-100 optional paper feeder is installed, use the same procedure
to load paper into the paper feeder cassettes.
1
Pull the cassette out of the printer.
2
Adjust the position of the width guides located on the left and right
sides of the cassette. Press the release button on the left guide and
slide the guides to the paper size required, and load the paper into
the cassette.
Proceed to the next section to select the paper size from the operation
panel.
Setting the Paper Size from the Operation Panel
Use the operation panel to set the size of paper loaded in the cassette
on the printer.
1
2
>Cassette Size >
? Custom
Press Z while Paper Settings > is displayed.
Press U or V repeatedly until >Cassette Size > appears. If
optional paper feeders are added, Cassette1 Size will appear for
the standard paper cassette and Cassette2 Size, and
Cassette3 Size will appear for the optional paper feeders.
3
Press [OK]. A blinking question mark (?) appears.
4
Press U or V to display the desired paper size. The message
display toggles through the following paper sizes:
Envelope C5
Executive
Letter
Legal
A4
B5
A5
A6
ISO B5
Custom
Oficio II
216x340mm
16K
Using the Operation Panel
2-21
Statement
Folio
Note A6 and Statement are displayed for Cassette
Size or Cassette 1 Size.
5
When the desired paper size is displayed, press [OK]. The paper
size is set for the paper cassette.
If you selected Custom in step 4, be sure to set the unit of
measurement and the dimensions of the paper as described in the
following sections.
Select the units of measurement as described in the next section.
Unit (Selecting the unit of measurement)
>>Unit
? mm
1
2
Press Z.
3
Press [OK]. A blinking question mark (?) appears.
4
5
Select mm or inch using U or V.
Press U or V repeatedly until >>Unit appears. The unit of
measurement can be selected between millimeters and inches. The
current unit of measurement is displayed (the default setting is mm).
Press [OK].
Set the dimensions of the paper as described in the next section.
Entering the Width and Length
X Dimension
105 to 216mm
(4-1/8 to 8-1/2 inches)
>>X Dimension
1
When the unit of measurement is set, press V.
>>X Dimension appears (the paper width setting).
2
Press [OK]. A blinking cursor (_) appears.
148 to 356mm
(5-13/16 to 14 inches)
Y Dimension
Enter the paper size for X Dimension and Y Dimension as shown in
the figure.
216 mm
2-22
Using the Operation Panel
3
Press U or V to increase or decrease the value of the figure where
the cursor is blinking and display the desired width.
Acceptable paper widths are as follows:
•
•
4
5
Display the paper width and press [OK].
When the width is set, pressV. >>Y Dimension appears (the paper
length setting). Set the desired length in the same way as the width.
Acceptable paper lengths are as follows:
•
•
6
7
Cassette: 105 to 216 mm (4.13 to 8.5 inches)
Paper Feeder PF-100 (optional): 148 to 216 mm (5.83 to
8.5 inches)
Cassette: 148 to 356 mm (5.83 to 14.02 inches)
Paper Feeder PF-100 (optional): 210 to 356 mm (8.27 to
14.02 inches)
Display the paper length, press [OK].
Press [MENU]. The display returns to Ready.
Cassette (1 to 3) Type (Setting the cassette paper
type)
By setting a paper type (plain, recycled, etc.) for the paper cassette, you
can automatically select the paper in the paper cassette according to the
paper type you command on the printer driver. The default setting is
plain paper for all paper cassettes.
If the PF-100 optional paper feeder is installed, use the same procedure
to setting the cassette paper type.
For more information about paper types that you can feed from the paper
cassette, refer to Paper Specifications on page 1-2.
1
2
Press Z while Paper Settings > is displayed.
Press U or V repeatedly until >Cassette Type appears.
If optional paper feeders are added, Cassette 1 Type will appear
for the standard paper cassette and Cassette 2 Type, and
Cassette 3 Type will appear for the optional paper feeders.
>Cassette Type
? PLAIN
3
To change paper type, press [OK]. A blinking question mark (?)
appears.
4
Press U or V to display the desired paper type. The message display
toggles through the following paper types:
PLAIN
PREPRINTED
BOND
RECYCLED
ROUGH
LETTERHEAD
COLOR
PREPUNCHED
HIGH QUALITY
CUSTOM 1 (to 8)
Note You can define any paper type and store that definition
in the printer. For more information, refer to Type Adjust
(Creating custom paper type) on page 2-24.
Using the Operation Panel
2-23
5
6
Press [OK].
Press [MENU]. The display returns to Ready.
Type Adjust (Creating custom paper type)
The following describes the procedure used to set a user-defined paper
type for the printer. Eight custom user settings may be registered. After
having been set, any of these may be called up when setting the paper
type for a paper source.
The paper weight and duplex path can be set (refer to Paper Weight
(Setting the paper weight) on page 2-24, and Duplex Path (Setting
the duplex path) on page 2-25) after selecting the paper type to be
customized as follows. For how to reset the customized settings, refer to
Reset Type Adjust (Resetting the custom paper type) on page 2-25.
>Type Adjust
? PLAIN
>
1
2
Press Z while Paper Settings > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
Press U or V to display the desired paper type. The display changes
as shown below.
Press U or V repeatedly until >Type Adjust > appears.
PLAIN
TRANSPARENCY
PREPRINTED
LABELS
BOND
RECYCLED
VELLUM
ROUGH
LETTERHEAD
COLOR
PREPUNCHED
ENVELOPE
CARDSTOCK
THICK
HIGH QUALITY
CUSTOM 1 (to 8)
5
6
Press [OK].
Press Z and proceed to the next step Paper Weight (Setting the
paper weight).
Paper Weight (Setting the paper weight)
You can set the paper thickness for your custom paper type to be
customized.The default setting is Normal 2.
>>Paper Weight
? Normal 2
2-24
1
Display the custom paper type (refer to Type Adjust (Creating
custom paper type) on page 2-24) and press Z.
2
Press U or V repeatedly until >>Paper Weight appears.
3
Press [OK]. A blinking question mark (?) appears.
Using the Operation Panel
4
Press U or V to display the desired paper thickness. The display
changes as shown below. For details of the default setting for each
paper type, refer to Paper Specifications on page 1-2.
Light
Normal 1
Normal 2
Normal 3
Heavy 1
Heavy 2
Heavy 3
Extra Heavy
5
6
Press [OK].
Press [MENU]. The display returns to Ready.
Duplex Path (Setting the duplex path)
>>>Duplex Path
? Enable
1
Display the custom paper type (refer to Type Adjust (Creating
custom paper type) on page 2-24) and press Z.
2
Press U or V repeatedly until >>Duplex Path appears.
3
Press [OK]. A blinking question mark (?) appears.
4
Select Enable or Disable using U or V. For details of the default
setting for each paper type, refer to Paper Specifications on page 12.
5
6
Press [OK].
Press [MENU]. The display returns to Ready.
The custom paper type setting is completed.
Reset Type Adjust (Resetting the custom paper type)
Reset all the custom paper type that was set in Type Adjust (Creating
custom paper type) on page 2-24.
>Reset Type Adjust ?
Using the Operation Panel
1
2
Press Z while Paper Settings > is displayed.
3
Press [OK]. A question mark (?) appears.
4
Press [OK] again. All customized paper types will be reset to the
default. The display returns to Ready.
Press U or V repeatedly until >Reset Type Adjust appears.
2-25
Print Settings
These settings specify printing parameters such as the print quality used
for printing (Normal or Fine), the number of copies, reduced printing and
the page orientation.
The options available in Print Settings are as follows:
• Paper Source (Selecting the paper feed source)
• Auto Cass. Change (Auto Cassette Change setting)
• MP Tray Priority (The settings for priority paper feed from the MP tray)
• Paper Feed Mode (Setting the paper feed source)
• Duplex (Duplex printing)
• Override A4/LT (Overriding difference between A4 and Letter)
• Emulation (Setting the emulation)
• Font Select (Selecting the default font)
• Code Set (Setting the code set)
• Print Quality (Setting print quality)
• Page Set (Setting pagination)
• Job Name (The Job Name display settings)
Print Settings
>
1
Press [MENU].
2
Press U or V repeatedly until Print Settings > appears.
Paper Source (Selecting the paper feed source)
You can select the paper source, from which the printer feeds paper as
the default. If an optional paper feeder(s) is installed, it is also available
for the default paper source.
>Paper Source
? Cassette 1
1
2
Press Z while Print Settings > is displayed.
3
To change the current paper feed source, press [OK]. A blinking
question mark (?) appears.
4
Press U or V to display the desired paper feed source. The message
display toggles through the following paper feed sources, depending
on the installed optional paper feeders (from the top most paper
cassette to the bottom paper cassette):
Press U or V repeatedly until >Paper Source appears.
MP tray
Cassette 1
Cassette 2
Cassette 3
Cassettes 2 and 3 are available for selection when the optional
paper feeders are installed.
5
6
2-26
Press [OK].
Press [MENU]. The display returns to Ready.
Using the Operation Panel
Auto Cass. Change (Auto Cassette Change setting)
You can select the following actions when the paper runs out in the
paper source while printing. By default, this feature is On.
>Auto Cass. Change
? On
Off
The printer displays Load Cassette # (# is a cassette
number) or Load MP Tray, and stops printing.
Load the paper according to the paper source displayed to
resume printing.
To print from the other paper cassette, press U or V to
display Use alternative?, press U or V to select the
desired paper source, and then press [GO].
On
The printer continues printing automatically when the other
paper cassette contains the same paper as the currentlyused paper cassette.
1
2
Press Z while Print Settings > is displayed.
3
To change the current paper feed source, press [OK]. A blinking
question mark (?) appears.
4
Select On or Off using U or V.
5
6
Press [OK].
Press U or V repeatedly until >Auto Cass. Change appears.
Press [MENU]. The display returns to Ready.
Note You can also configure the Auto Cassette Change in the
Embedded Web Server RX. Access to the Embedded Web
Server RX, and then go to Basic > Defaults > Device Defaults
page. For more information on access to the Embedded Web
Server RX, refer to the Embedded Web Server RX User Guide.
MP Tray Priority (The settings for priority paper feed
from the MP tray)
If paper is set in the MP Tray then it is possible for priority to be given to
that MP tray in the paper feed. The default setting is Off.
>MP Tray Priority
? Off
1
2
Press Z while Print Settings > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
Press U or V to select the desired MP tray priority mode. The list
shows the following MP tray priority mode:
Press U or V repeatedly until >MP Tray Priority appears.
Off (The printer driver settings are followed.)
Auto Feed (If Auto is selected in the printer driver and there is
paper in the MP tray then the paper feed will be from the MP tray.)
Always (If there is paper in the MP tray then the paper feed will be
from the MP tray regardless of what is set in the printer driver.)
5
Using the Operation Panel
Press [OK].
2-27
6
Press [MENU]. The display returns to Ready.
Paper Feed Mode (Setting the paper feed source)
This mode specifies how the paper should be fed once the paper feed
source and paper type have been chosen. If Auto is selected, the printer
searches for a paper feed source that matches the paper size and type,
and paper is then delivered from that source. If Fixed is selected and
there is no matching paper feed source, handling proceeds as specified
by Paper Mismatch for Error Handling. For details on paper
feeding when Fixed is selected, refer to Paper Mismatch (Detection
settings for paper size/type errors when the paper source is fixed)
on page 2-61. The default setting is Auto. To change the settings, follow
the steps described below.
>Paper Feed Mode
? Auto
1
2
Press Z while Print Settings > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Press U or V until Auto or Fixed appears.
Press U or V repeatedly until >Paper Feed Mode appears.
Press [OK].
Press [MENU]. The display returns to Ready.
When the Paper Runs Out During Printing
When Paper Feed Mode is set to Fixed, if the paper in the cassette
runs out during printing, Load Cassette 1 is displayed and the printer
stands by. In this event, either replenish the paper in the empty cassette
or use the procedure below to print from another paper source.
1
While Load Cassette 1 is displayed, press U or V repeatedly until
Use alternative? appears.
2
Press U or V repeatedly until the desired paper source and size
appears.
Each time you press U or V, another paper cassette or the paper
size that can currently be fed from the MP tray appears.
3
2-28
Press [OK]. Printing continues.
Using the Operation Panel
Duplex (Duplex printing)
Using the duplexer, you can automatically print on both sides of the
paper. The duplexer is mounted underneath the printer.
Duplex printing is available for the following paper types:
PLAIN
PREPRINTED
BOND
RECYCLED
ROUGH
LETTERHEAD
COLOR
PREPUNCHED
THICK
HIGH QUALITY
Activating the duplexer is done by selecting either short edge or long
edge binding mode.
Note Duplex printing can be also performed from the MP tray. If
the paper to be fed from the MP tray does not match the paper
size and paper type of the current paper feed source cassette, a
paper jam may occur.
Binding Modes
Binding refers to the manner in which printed pages of paper are joined
together (by gluing, stitching, etc.) in book form. The two possible types
of binding are: long-edge binding, in which pages are joined together
along their long edge; and short-edge binding, in which they are joined
together along their short edge. In selecting a binding type, you must
also consider the orientation of the printed page. You can use long-edge
or short-edge binding with either landscape or portrait printing.
Depending on the binding type and print orientation, the duplexer
provides four types of binding. These are: (1) portrait, long-edge, (2)
portrait, short edge, (3) landscape, long-edge, and (4) landscape, shortedge. The figure below shows these binding methods.
(1)
(2)
Portrait,
long-edge
Portrait,
short-edge
Landscape,
short-edge
(3)
Landscape,
long-edge
>Duplex
? Off
Using the Operation Panel
(4)
1
2
Press Z while Print Settings > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
Press U or V repeatedly until >Duplex appears.
2-29
4
Press U or V to display the desired binding mode. The message
display toggles through the following:
Off (default)
Short edge bind
Long edge bind
5
6
Press [OK].
Press [MENU]. The display returns to Ready.
Override A4/LT (Overriding difference between A4
and Letter)
When the Override A4/LT is turned On using the operation panel, the
printer ignores the difference between A4 and Letter paper sizes.
Printing is performed without an error message even if the actual paper
size in the current cassette differs from the paper size formatting the job.
By default, this feature is Off.
>Override A4/LT
? Off
1
Press Z while Print Settings > is displayed.
2
Press U or V repeatedly until >Override A4/LT appears.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
Press [OK].
Press [MENU]. The display returns to Ready.
Emulation (Setting the emulation)
You can change the emulation mode for the current interface. Use the
procedure below to select the mode.
>Emulation
? PCL 6
1
2
Press Z while Print Settings > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
Press U or V repeatedly until the desired emulation mode is
displayed.
Press U or V repeatedly until >Emulation > appears on the
message display. One of the emulation modes appears, indicating
the emulation currently in use.
PCL 6
KPDL
KPDL (AUTO)
Line Printer
IBM Proprinter
EPSON LQ-850
Note The default setting for North America is KPDL (AUTO)
emulation. The default setting for all other regions is PCL 6
emulation.
5
6
2-30
Press [OK].
Press [MENU]. The display returns to Ready.
Using the Operation Panel
Alternative Emulation for KPDL Emulation
KPDL is Kyocera’s implementation of the PostScript language. The
KPDL (AUTO) emulation enables the printer to automatically change the
emulation mode according to the data received when printing.
In addition to KPDL (AUTO) emulation, you can use the operation panel
to set another emulation mode that is used very often. The default
setting is PCL 6.
1
2
>Emulation
? PCL 6
>Emulation
? KPDL (AUTO)
>>Alt. Emulation
PCL 6
Press [MENU].
Press U or V repeatedly until >Emulation > appears on the
message display.
3
Press [OK]. A blinking question mark (?) appears.
4
Press U or V repeatedly until KPDL (AUTO) appears.
5
6
Press [OK].
7
8
Press Z. When >>Alt. Emulation is displayed, press U or V.
The names of alternative emulations appear - PCL 6, Line
Printer, IBM Proprinter or EPSON LQ-850.
Press [OK]. A blinking question mark (?) appears.
Press U or V repeatedly until the desired alternative emulation
appears.
9 Press [OK].
10 Press [MENU]. The display returns to Ready.
Error Report (Printing KPDL errors)
The printer can print error descriptions when printing error occurs during
KPDL emulation.
Note The default setting for North America is Off. The default
setting for all other regions is On.
>Emulation
? PCL 6
>Emulation
? KPDL (AUTO)
Using the Operation Panel
>
1
2
Press Z while Print Settings > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
Select KPDL or KPDL (AUTO) using U or V. Press [OK].
5
6
Press Z. >>Error Report appears.
Press U or V repeatedly until >Emulation > appears.
Press [OK]. A blinking question mark (?) appears.
2-31
>>Error Report
? On
7
Select On or Off using U or V. Press [OK].
8
Press [MENU]. The display returns to Ready.
Font Select (Selecting the default font)
You can select the default font. The default font can be one of the
internal fonts or a font that is downloaded to the printer memory.
In this menu, you can also set the type and pitch for Courier and Letter
Gothic; as well as to print a font list.
>Font Select
Internal
>
>> I000
1
2
Press Z while Print Settings > is displayed.
3
To select an internal font, make sure that Internal is displayed
and press Z. The display changes. If Internal is not displayed, press
[OK], then press U or V until it appears.
Press U or V repeatedly until >Font Select > appears.
To select an optional font, press [OK] while >Font Select > is
displayed. Press U or V repeatedly until Option appears and then
press [OK]. Press Z next to display the font selection shown above.
You can perform this operation only when optional fonts are installed
in the printer.
The letter before the number indicates the location of the font, as
shown below.
I: Internal font
S: Soft (downloaded) font
H: Fonts in RAM disk
>>?I000
4
Press [OK]. A blinking question mark (?) appears.
5
Press U or V repeatedly until the desired font number appears. For
font numbers of the internal fonts, refer to Print Fonts List on
page 2-15.
6
7
When the desired font is displayed, press [OK].
Press [MENU]. The display returns to Ready.
Selecting Regular or Dark Courier/Letter Gothic
Courier or Letter Gothic font thickness can be selected as Regular or
Dark. In the procedure below, it is assumed that Courier is selected. The
procedure is the same for Letter Gothic.
>Font Select
Internal
2-32
>
1
2
Press Z while Print Settings > is displayed.
3
Make sure that Internal is displayed and press Z.
Press U or V repeatedly until >Font Select > appears.
Using the Operation Panel
>>Courier
Regular
>>Courier
? Regular
4
Press U or V repeatedly until >>Courier appears. If you are
selecting the thickness of the Letter Gothic font, choose >> Letter
Gothic here instead.
5
Press [OK]. A blinking question mark (?) appears.
6
7
8
Select Regular or Dark using U or V.
Press [OK].
Press [MENU]. The display returns to Ready.
Changing the Default Font Size
You can change the size of the default font. If you selected a proportional
font, the character size can also be changed.
>Font Select
Internal
>
>>Size
012.00 point(s)
>>Size
012.00 point(s)
1
2
Press Z while Print Settings > is displayed.
3
4
Make sure that Internal is displayed and press Z.
5
Press [OK]. A blinking question mark (?) appears.
6
Press U or V to increase or decrease the value at the blinking
cursor. The font size can be set between 4 and 999.75 points, in
0.25-point increments. Use Z or Y to move the cursor right and left.
7
8
When the desired size is displayed, press [OK].
Press U or V repeatedly until >Font Select > appears.
Press U or V repeatedly until >>Size appears.
Press [MENU]. The display returns to Ready.
Character Pitch
You can set the character pitch for fixed fonts.
>Font Select
Internal
>
>>Pitch
1
2
Press Z while Print Settings > is displayed.
3
4
Make sure that Internal is displayed and press Z.
Press U or V repeatedly until >Font Select > appears.
Press U or V repeatedly until >>Pitch appears.
10.00 cpi
Using the Operation Panel
2-33
>>Pitch
5
Press [OK]. A blinking question mark (?) appears.
6
Press U or V to increase or decrease the value at the blinking
cursor. The character pitch can be set 0.44 and 99.99 characters per
inch, in 0.01 character-per-inch increments. Use Z or Y to move the
cursor right and left.
7
8
When the desired size is displayed, press [OK].
10.00 cpi
Press [MENU]. The display returns to Ready.
Code Set (Setting the code set)
You can change the character code set. Available character code sets
vary depending on the current font. (The default is IBM PC-8.)
>Code Set
IBM PC-8
>Code Set
? IBM PC-8
2-34
1
2
Press Z while Print Settings > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Press U or V until the desired character code set appears.
Press U or V repeatedly until >Code Set appears.
Press [OK].
Press [MENU]. The display returns to Ready.
Using the Operation Panel
Print Quality (Setting print quality)
This selects the gloss mode (Low or High) and whether EcoPrint (lowtoner printing) is used for printing.
The options available in Print Quality are as follows:
• KIR Mode (Selecting the KIR mode)
• EcoPrint Mode (Selecting the EcoPrint mode)
• Resolution (Selecting the print resolution)
• Print Density (Selecting the print density)
>Print Quality
>
1
Press Z while Print Settings > is displayed.
2
Press U or V repeatedly until >Print Quality > appears.
KIR Mode (Selecting the KIR mode)
This printer incorporates the KIR (Kyocera Image Refinement)
smoothing function. KIR users the software to enhance resolution,
resulting in high quality printing at resolution of 600 dpi and 300 dpi. The
default is On. KIR has no effect on the printing speed.
with KIR Off
>>KIR Mode
? On
Using the Operation Panel
with KIR On (default)
1
2
Press Z while >Print Quality > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
Press U or V repeatedly until >>KIR Mode appears.
Press [OK].
Press [MENU]. The display returns to Ready.
2-35
EcoPrint Mode (Selecting the EcoPrint mode)
By enabling EcoPrint mode, you can minimize the amount of toner used
during printing. Because images printed in this mode may be slightly
coarser than those printed in standard resolution, you should use
EcoPrint for test prints or other situations where high-quality prints are
not required.
Use the procedure below to select EcoPrint mode. The default setting is
Off.
>>EcoPrint Mode
? Off
1
2
Press Z while >Print Quality > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
Press U or V repeatedly until >>EcoPrint Mode appears.
Press [OK].
Press [MENU]. The display returns to Ready.
Resolution (Selecting the print resolution)
You can set the default print resolution in four ways: 300dpi, 600dpi, Fast
1200 mode and Fine 1200 mode. The clarity of printed characters and
graphics becomes sharper in this order.
>>Resolution
? Fast 1200 mode
1
2
Press Z while >Print Quality > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
Select Fine 1200 mode, Fast 1200 mode, 600 dpi or 300
dpi using the U or V.
5
6
Press [OK].
Press U or V repeatedly until >>Resolution appears.
Press [MENU]. The display returns to Ready.
Print Density (Selecting the print density)
The print density can be adjusted in five steps: from 01 (light) to 05
(dark). The factory setting is 03.
>>Print Density
? 03
2-36
1
2
Press Z while >Print Quality > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
Select the print density from five steps from 01 (light) to 05 (dark)
using the U or V.
5
6
Press [OK].
Press U or V repeatedly until >>Print Density appears.
Press [MENU]. The display returns to Ready.
Using the Operation Panel
Page Set (Setting pagination)
In Page Set menus, you can set the number of copies, page orientation,
and other settings regarding pagination.
The options available in Page Set are as follows:
• Copies (Number of copies)
• Orientation (Print orientation)
• LF Action (Linefeed)
• CR Action (Carriage-Return)
• Wide A4 (Wide A4 pitch)
• XPS FitTo Page (Print area setting for XPS data)
• TIFF/JPEG Size (Print mode setting for TIFF/JPEG files)
>Page Set
>
1
Press Z while Print Settings > is displayed.
2
Press U or V repeatedly until >Page Set > appears.
Copies (Number of copies)
You can set the number of copies of each page to be printed for the
current interface.
>>Copies
1
2
Press Z while >Page Set > is displayed.
3
Press [OK]. A blinking cursor (_) appears.
4
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. The number of copies can be set between 1 and 999.
Use Y and Z to move the cursor right and left.
5
6
When the desired size is displayed, press [OK].
Press U or V repeatedly until >>Copies appears.
001
Press [MENU]. The display returns to Ready.
Orientation (Print orientation)
You can select portrait (upright) or landscape (sideways) page
orientation.
Portrait Orientation
A
1
2
Using the Operation Panel
Landscape Orientation
A
Press Z while >Page Set > is displayed.
Press U or V repeatedly until >>Orientation appears.
2-37
>>Orientation
? Portrait
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select Portrait or Landscape using U or V.
Press [OK].
Press [MENU]. The display returns to Ready.
LF Action (Linefeed)
This procedure instructs the printer what to do when it receives a
linefeed code (0AH).
>>LF Action
? LF only
•
•
•
LF only: Linefeed is performed (Default).
CR and LF: A linefeed and carriage return are performed.
Ignore LF: The linefeed is ignored.
1
2
Press Z while >Page Set > is displayed.
3
Press [OK]. A blinking cursor (_) appears.
4
5
6
Press U or V repeatedly until the desired linefeed action appears.
Press U or V repeatedly until >>LF Action appears.
When the desired action is displayed, press [OK].
Press [MENU]. The display returns to Ready.
CR Action (Carriage-Return)
This procedure instructs the printer what to do when it receives a
carriage return code (0DH).
>>CR Action
? CR only
2-38
•
•
•
CR only: A carriage-return is performed (Default).
CR and LF: A linefeed and carriage return are performed.
Ignore CR: The carriage-return is ignored.
1
2
Press Z while >Page Set > is displayed.
3
Press [OK]. A blinking cursor (_) appears.
4
5
6
Press U or V repeatedly until the desired carriage-return appears.
Press U or V repeatedly until >>CR Action appears.
When the desired action is displayed, press [OK].
Press [MENU]. The display returns to Ready.
Using the Operation Panel
Wide A4 (Wide A4 pitch)
Turn this to On to increase the maximum number of characters that can
be printed in a line for an A4 page (78 characters at 10 pitch) and Letter
size page (80 characters at 10 pitch). This setting is only effective in PCL
6 emulation.
>>Wide A4
? Off
1
2
Press Z while >Page Set > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
Press U or V repeatedly until >>Wide A4 appears.
Press [OK].
Press [MENU]. The display returns to Ready.
XPS FitTo Page (Print area setting for XPS data)
Select On in this setting to enlarge or reduce XPS files to fit the printable
area during printing.
>>XPS FitTo Page
? Off
1
2
Press Z while >Page Set > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
Press U or V repeatedly until >>XPS FitTo Page appears.
Press [OK].
Press [MENU]. The display returns to Ready.
TIFF/JPEG Size (Print mode setting for TIFF/JPEG files)
Use this setting to select the printing method used when TIFF or JPEG
files are printed directly. The default setting is Paper Size.
>>TIFF/JPEG Size
? Paper Size
1
2
Press Z while >Page Set > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
Press U or V repeatedly until the desired print mode is displayed.
The list shows the following print modes:
Press U or V repeatedly until >>TIFF/JPEG Size appears.
Paper Size (scaled to fit the paper size)
Images are resized so that they fill the paper size when printed.
Image Resolution (matched to the image resolution)
Image files are printed at the resolution specified in the resolution
information. Images with no resolution information are printed using
the Paper Size setting.
Print Resolution (matched to the print resolution)
Using the Operation Panel
2-39
Images are printed using a 1-to-1 correspondence between the
image file pixels and printed dots. For example, the printed size of a
600 × 300-pixel image file is 1 inch × 1/2 inch.
5
6
Press [OK].
Press [MENU]. The display returns to Ready.
Note Images are automatically rotated during printing to provide
a closer match between the aspect ratios of the image file and the
paper used for printing.
Job Name (The Job Name display settings)
Set whether the job name set in the printer driver is displayed.
>Job Name
? Off
1
2
Press Z while Print Settings > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
Press U or V to display the job name to be used.
Press U or V repeatedly until >Job Name appears.
Off
Job Name (Use the job name set in the printer driver.)
Job No.+Job Name
Job Name+Job No.
5
6
2-40
When the desired job name is displayed, press [OK].
Press [MENU]. The display returns to Ready.
Using the Operation Panel
Network (Network settings)
This printer supports TCP/IP and TCP/IP (IPv6) protocols.
IP is an abbreviation for Internet Protocol. This printer routinely uses the
TCP/IP (IPv4) protocol, but provides a separate setting for the nextgeneration IP, IPv6.
TCP/IP (IPv4) uses 32-bit IP addresses, but the rapid growth in the
number of Internet users has resulted in a shortage of IP addresses.
IPv6 was developed to expand the range of available IP addresses by
using 128-bit IP addresses.
The options available in the Network settings are as follows:
• TCP/IP (IPv4 settings)
• TCP/IP (IPv6) (IPv6 settings)
• Protocol Detail (Detailed settings for the network protocol)
• Restart Network (Restarting the network card)
Note Check with your network administrator when selecting the
network setting. After all network related settings have been
done, restart the network. Refer to Restart Network (Restarting
the network card) on page 2-49. This is mandatory to make the
settings effective!
When Embedded Web Server RX is used, network parameters
and security settings can be conveniently changed and checked
from your PC. For more information, refer to the Embedded Web
Server RX User Guide.
Network
>
1
Press [MENU].
2
Press U or V repeatedly until Network > appears.
TCP/IP (IPv4 settings)
This selects the settings for TCP/IP (IPv4).
The TCP/IP system refers to the Internet system, which has a 5-layer
structure consisting of the interface layer, link layer, network (IP) layer,
transport (TCP/UDP) layer and application layer.
The interface layer is a key layer in the TCP/IP system that provides an
abstracted interface that is not dependent on the link (communication
line: frame relay or Ethernet, etc.) to the IP module (IP layer). This
means that the IP module can use this abstracted interface (which is not
dependent on the link type) to exchange IP packets back and forth with
the link layer.
The options available in the TCP/IP (IPv4) settings are as follows:
• DHCP (DHCP setting)
• Auto-IP (Auto-IP setting)
• IP Address (IP address setting)
• Subnet Mask (Subnet mask setting)
• Gateway (Gateway setting)
• Bonjour (Bonjour setting)
Using the Operation Panel
2-41
IMPORTANT The DHCP, IP address, subnet mask, gateway and
Bonjour menu options for TCP/IP are displayed when TCP/IP is enabled.
>TCP/IP
? Off
>
1
2
Press Z while Network > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
Select On or Off using U or V.
Press U or V repeatedly until >TCP/IP > appears.
Select On and press [OK]. Configure the settings shown below.
DHCP (DHCP setting)
DHCP (Dynamic Host Configuration Protocol) is the protocol that
assigns the information required to establish a network connection when
a host attempts to connect to the network (Internet). This information
includes the IP address of the local node and the default router (the
router in the host's own network system) and the DNS (Domain Name
System) server. DHCP is an extension of the BOOTP (Bootstrap) startup
protocol.
>>DHCP
? Off
1
Press Z while >TCP/IP
2
Press U or V repeatedly until >>DHCP appears.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
On > is displayed.
Press [OK].
Press [MENU]. The display returns to Ready.
Auto-IP (Auto-IP setting)
This protocol is used for automatic assignment of an IP address when
you connect to a small network that does not have a DHCP server.
Select an address from the range 169.254.0.1 to 169.254.255.254, and
if no other device on the network is using that address, it is used as your
address.
>>Auto-IP
? Off
2-42
1
2
Press Z while >TCP/IP
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
On > or >TCP/IP
Off > is displayed.
Press U or V repeatedly until >>Auto-IP appears.
Press [OK].
Press [MENU]. The display returns to Ready.
Using the Operation Panel
IP Address (IP address setting)
An IP address is the address of a network device such as a computer
and is included in IP packets as needed for the sending and receiving of
Internet data (IP packets). (IP addresses can be either destination
addresses or source addresses.)
Specifically, an IP address is a bit string consisting of a host address (or
host section) that identifies a computer connected to the Internet and a
network address (or network section) that identifies the network to which
that computer belongs (or more specifically, the computer's network
interface). Bit strings (IP addresses) that are unique throughout the
entire Internet system are allocated to each computer or interface.
The IP addresses currently used on the Internet (IPv4) have a fixed
length of 32 bits.
Note When you enter the IP address, be sure to set the DHCP
setting to Off.
>>IP Address
000.000.000.000
1
2
Press Z while >TCP/IP
3
Press [OK]. A blinking cursor (_) appears.
4
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. You can set any value between 000 and 255. Use Y
and Z to move the cursor right and left.
5
6
Display the desired IP address and press [OK].
On > is displayed.
Press U or V repeatedly until >>IP Address appears.
Press [MENU]. The display returns to Ready.
Subnet Mask (Subnet mask setting)
The subnet mask is a way of augmenting the network address section of
an IP address.
A subnet mask represents all network address sections as 1 and all host
address sections as 0. The number of bits in the prefix indicates the
length of the network address. The term "prefix" refers to something
added to the beginning and, in this context, indicates the first section of
the IP address.
When an IP address is written, the length of the network address can
indicated by the prefix length after a forward slash (/). For example, "24"
in the address "133.210.2.0/24". In this way, "133.210.2.0/24" denotes
the IP address "133.210.2.0" with a 24-bit prefix (network section).
This new network address section (originally part of the host address)
made possible by the subnet mask is referred to as the subnet address.
Note When you enter the subnet mask, be sure to set the DHCP
setting to Off.
>>Subnet Mask
000.000.000.000
Using the Operation Panel
1
2
Press Z while >TCP/IP
3
Press [OK]. A blinking cursor (_) appears.
On > is displayed.
Press U or V repeatedly until >>Subnet Mask appears.
2-43
4
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. You can set any value between 000 and 255. Use Y
and Z to move the cursor right and left.
5
6
Display the desired subnet mask and press [OK].
Press [MENU]. The display returns to Ready.
Gateway (Gateway setting)
Gateway generally refers to a protocol conversion device used to allow
networks with differing protocol systems to interconnect.
For example, a "Gateway" device is required to connect a different
closed network (using its own protocols) to the open Internet (using
TCP/IP).
By installing a gateway, the communications protocols and data display
modes on different networks can be made compatible.
On TCP/IP networks, the term gateway is used to refer to routers.
Note Before you input the gateway, be sure to set the DHCP
setting to Off.
>>Gateway
000.000.000.000
1
2
Press Z while >TCP/IP
3
Press [OK]. A blinking cursor (_) appears.
4
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. You can set any value between 000 and 255. Use Y
and Z to move the cursor right and left.
5
6
Display the desired gateway and press [OK].
On > is displayed.
Press U or V repeatedly until >>Gateway appears.
Press [MENU]. The display returns to Ready.
Bonjour (Bonjour setting)
Bonjour, also known as zero-configuration networking, is a service that
automatically detects computers, devices and services on an IP network.
Bonjour, because an industry-standard IP protocol is used, allows
devices to automatically recognize each other without an IP address
being specified or DNS server being set.
Bonjour also sends and receives network packets by UDP port 5353. If a
firewall is enabled, the user must check that UDP port 5353 is left open
so that Bonjour will run correctly. Some firewalls are set up so as to
reject only certain Bonjour packets. If Bonjour does not run stably, check
the firewall settings and ensure that Bonjour is registered on the
exceptions list and that Bonjour packets are accepted. If you install
Bonjour on Windows XP Service Pack 2 or later, the Windows firewall
will be set up correctly for Bonjour.
>>Bonjour
? Off
2-44
1
2
Press Z while >TCP/IP
3
Press [OK]. A blinking cursor (_) appears.
On > is displayed.
Press U or V repeatedly until >>Bonjour appears.
Using the Operation Panel
4
5
6
Select On or Off using U or V.
Press [OK].
Press [MENU]. The display returns to Ready.
TCP/IP (IPv6) (IPv6 settings)
This selects the settings for TCP/IP (IPv6).
TCP/IP (IPv6) is based on the current Internet protocol, TCP/IP (IPv4).
IPv6 is the next-generation Internet protocol and expands the available
address space, which resolves the problem of the lack of addresses
under IPv4, while also introducing other improvements such as
additional security functionality and the capacity to prioritize data
transmission.
The options available in the TCP/IP (IPv6) settings are as follows:
• RA (Stateless) (RA (Stateless) setting)
• DHCPv6 (DHCPv6 setting)
IMPORTANT The RA (Stateless) and DHCPv6 menu options for
TCP/IP (IPv6) are displayed when TCP/IP (IPv6) is enabled.
>TCP/IP (IPv6) >
? Off
1
2
Press Z while Network > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
Select On or Off using U or V.
Press U or V repeatedly until >TCP/IP (IPv6) > appears.
Select On and press [OK]. Configure the settings shown below.
RA (Stateless) (RA (Stateless) setting)
The IPv6 router communicates (transmits) information such as the global
address prefix using ICMPv6. This information is the Router
Advertisement (RA).
ICMPv6 stands for Internet Control Message Protocol, and is a IPv6
standard defined in the RFC 2463 "Internet Control Message Protocol
(ICMPv6) for the Internet Protocol Version 6 (IPv6) Specification".
>>RA(Stateless)
? Off
Using the Operation Panel
1
2
Press Z while >TCP/IP (IPv6)
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
On > is displayed.
Press U or V repeatedly until >>RA(Stateless) appears.
Press [OK].
Press [MENU]. The display returns to Ready.
2-45
DHCPv6 (DHCPv6 setting)
DHCPv6 is the next-generation of the Internet's Dynamic Host
Configuration Protocol and supports IPv6. It extends the BOOTP startup
protocol that defines the protocols used for transferring configuration
information to hosts on the network.
DHCPv6 permits the DHCP server to use its expanded functionality to
send configuration parameters to an IPv6 node. Because the network
addresses that can be used are allocated automatically, the IPv6 node
management workload is reduced in systems where the administrator
has to exercise close control over IP address allocation.
>>DHCPv6
? Off
1
2
Press Z while >TCP/IP (IPv6)
3
Press [OK]. A blinking question mark (?) appears.
4
Select On or Off using U or V.
5
6
Press [OK].
On > is displayed.
Press U or V repeatedly until >>DHCPv6 appears.
Press [MENU]. The display returns to Ready.
Protocol Detail (Detailed settings for the network
protocol)
This selects the settings for Protocol Detail.
The options available in the Protocol Detail settings are as follows:
• NetBEUI (NetBEUI setting)
• SNMPv3 (SNMPv3 setting)
• FTP (Server) (FTP (Server) setting)
• SNMP (SNMP setting)
• SMTP (SMTP setting)
• POP3 (POP3 setting)
• RAW Port (RAW Port setting)
• LPD (LPD setting)
• HTTP (HTTP setting)
1
2
Press Z while Network > is displayed.
Press U or V repeatedly until >Protocol Detail > appears.
NetBEUI (NetBEUI setting)
Selects whether or not to receive documents using NetBEUI.
>>NetBEUI
? On
2-46
1
2
Press Z while >Protocol Detail > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
Select On or Off using U or V.
Press U or V repeatedly until >>NetBEUI appears.
Press [OK].
Using the Operation Panel
6
Press [MENU]. The display returns to Ready.
SNMPv3 (SNMPv3 setting)
Set SNMPv3.
>>SNMPv3
? Off
1
2
Press Z while >Protocol Detail > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
Press U or V repeatedly until >>SNMPv3 appears.
Press [OK].
Press [MENU]. The display returns to Ready.
FTP (Server) (FTP (Server) setting)
Select whether or not to receive documents using FTP.
>>FTP(Server)
? On
1
2
Press Z while >Protocol Detail > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
Press U or V repeatedly until >>FTP(Server) appears.
Press [OK].
Press [MENU]. The display returns to Ready.
SNMP (SNMP setting)
Select whether or not to communicate using SNMP.
>>SNMP
? On
1
2
Press Z while >Protocol Detail > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
Press U or V repeatedly until >>SNMP appears.
Press [OK].
Press [MENU]. The display returns to Ready.
SMTP (SMTP setting)
Select whether or not to send email using SMTP.
1
2
Using the Operation Panel
Press Z while >Protocol Detail > is displayed.
Press U or V repeatedly until >>SMTP appears.
2-47
>>SMTP
? Off
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
Press [OK].
Press [MENU]. The display returns to Ready.
POP3 (POP3 setting)
Select whether or not to receive email using POP3.
>>POP3
? Off
1
2
Press Z while >Protocol Detail > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
Press U or V repeatedly until >>POP3 appears.
Press [OK].
Press [MENU]. The display returns to Ready.
RAW Port (RAW Port setting)
Select whether or not to communicate using RAW Port.
>>RAW Port
? On
1
2
Press Z while >Protocol Detail > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
Press U or V repeatedly until >>RAW Port appears.
Press [OK].
Press [MENU]. The display returns to Ready.
LPD (LPD setting)
Select whether or not to receive documents using LPD as the network
protocol.
>>LPD
? On
2-48
1
2
Press Z while >Protocol Detail > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
Press U or V repeatedly until >>LPD appears.
Press [OK].
Press [MENU]. The display returns to Ready.
Using the Operation Panel
HTTP (HTTP setting)
Select whether or not to communicate using HTTP.
>>HTTP
? On
1
2
Press Z while >Protocol Detail > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
Press U or V repeatedly until >>HTTP appears.
Press [OK].
Press [MENU]. The display returns to Ready.
Restart Network (Restarting the network card)
After all network related settings have been done, restart the network
card of the device. This is mandatory to make the settings effective.
>Restart Network ?
Using the Operation Panel
1
2
Press Z while Network > is displayed.
3
Press [OK]. A question mark (?) appears.
4
Press [OK] again. The message Restarting… Please wait.
appears and the network is restarted.
Press U or V repeatedly until >Restart Network appears.
2-49
Optional Network (Optional Network settings)
This selects the settings for the optional network interface kit (IB-50) or
wireless network interface kit (IB-51).
Note This is only displayed when a network interface kit (IB-50)
or wireless network interface kit (IB-51) is installed as an option.
Refer to the IB-51 User’s Manual for information on the wireless
network settings. Manual setting from the printer is not supported
on this device.
The options available in the Optional Network settings are as follows:
• ID (Administrator ID input)
• Password (Administrator Password input)
• TCP/IP (IPv4 settings)
• TCP/IP (IPv6) (IPv6 settings)
• Netware (NetWare setting)
• AppleTalk (AppleTalk setting)
• IPSec (IPSec setting)
• LAN Interface (LAN Interface setting)
• MACAddressFilter (MAC address filtering setting)
• Communication (Select the network interface to use)
• Restart Network (Restarting the optional network interface kit)
Optional Network
>
1
Press [MENU].
2
Press U or V repeatedly until Optional Network > appears.
ID (Administrator ID input)
To use the Optional Network function, you must enter an administrator
ID. For information on how to set the administrator ID, refer to
Administrator (Administrator settings) on page 2-81.
ID
_
1
Press Z while Optional Network > is displayed.
2
The message display shows ID and a blinking cursor (_).
3
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. Enter the specified ID. Use Y and Z to move the
cursor right and left. Enter an ID consisting of between 1 and 16
numbers.
4
Press [OK]. Proceed to the next step Password (Administrator
Password input).
Password (Administrator Password input)
To set up the Optional Network functions, you must enter an
administrator ID and administrator password. For information on how to
set the administrator password, refer to Administrator (Administrator
settings) on page 2-81.
2-50
Using the Operation Panel
Password
_
1
Once you have entered the correct ID in the previous step (ID
(Administrator ID input)), the message display shows Password
(Administrator password input) and a blinking cursor (_).
2
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. Enter the specified password. Use Y and Z to move
the cursor right and left. Enter a password consisting of between 0 (no
settings) and 16 numbers.
Note If you enter the incorrect administrator ID or password,
the message Wrong ID or Wrong Password appears and
the input screen then reappears. Re-enter the ID or password
correctly.
3
Press [OK]. The Security screen appears.
TCP/IP (IPv4 settings)
This selects the settings for TCP/IP (IPv4). The method for setting is the
same as for the standard Network settings. For details, refer to TCP/IP
(IPv4 settings) on page 2-41.
TCP/IP (IPv6) (IPv6 settings)
This selects the settings for TCP/IP (IPv6). The method for setting is the
same as for the standard Network settings. For details, refer to TCP/IP
(IPv6) (IPv6 settings) on page 2-45.
Netware (NetWare setting)
NetWare is a PC-based network operating system specifically for
servers. NetWare is a client-server system that operates by installing the
NetWare OS on the server and dedicated client modules (NetWare
clients) on the client machines (running MS-DOS, OS/2, Windows, etc.).
The basic network layer protocol used is NetWare's own IPX
(Internetwork Packet eXchange)/SPX (Sequenced Packet eXchange),
but the system also supports TCP/IP.
The feature of the NetWare OS is that it is specifically for servers, unlike
general-purpose operating systems such as Windows NT and UNIX.
Only the minimum required for server operation can be performed from
the NetWare OS console on the server. Server and file management is
basically carried out using management tools from the clients. Also, all
drivers and protocol stacks are in the form of modules called NetWare
Loadable Modules (NLMs), and the ability of NLMs to load and unload
flexibly and dynamically is a major advantage of this system.
>Netware
? On
Using the Operation Panel
1
After entering the administrator ID and password, press U or V
repeatedly until >Netware appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Press U or V to select whether NetWare is enabled.
Press [OK].
Press [MENU]. The display returns to Ready.
2-51
AppleTalk (AppleTalk setting)
AppleTalk is a communications protocol used primarily on Macintosh
computers and also refers to the Mac OS network functions.
AppleTalk assigns 24-bit network addresses (a 16-bit network section
and an 8-bit node address) that are used to identify devices (computers,
printers, etc.) on the network.
When the power is turned on, a broadcast signal is sent out onto the
network and the addresses and machine names are automatically
assigned. The default setting is On.
>AppleTalk
? On
1
After entering the administrator ID and password, press U or V
repeatedly until >AppleTalk appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
Press U or V to select whether AppleTalk is enabled.
5
Press [MENU]. The display returns to Ready.
Press [OK].
IPSec (IPSec setting)
IPSec (IP Security Protocol) is a security protocol adopted as the
standard by the IETF for authentication and encryption in the third
network layer (IP layer).
It can be used with both IPv4 and IPv6.
Note IPv4 uses 32-bit IP addresses and IPv6 uses 128-bit IP
addresses.
>IPSec
? Off
1
After entering the administrator ID and password, press U or V
repeatedly until >IPSec appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Press U or V to select whether IPSec is enabled.
Press [OK].
Press [MENU]. The display returns to Ready.
LAN Interface (LAN Interface setting)
Specify the settings for the LAN interface to be used. The default setting
is Auto.
Note LAN Interface is only displayed when the optional network
interface kit (IB-50) is installed.
1
2-52
After entering the administrator ID and password, press U or V
repeatedly until >LAN Interface appears.
Using the Operation Panel
>LAN Interface
? Auto
2
Press [OK]. A blinking question mark (?) appears.
3
Press U or V to select the desired LAN Interface. The available LAN
Interface are as follows:
Auto
10BASE-Half
10BASE-Full
100BASE-Half
100BASE-Full
1000BASE-T
4
5
Press [OK].
Press [MENU]. The display returns to Ready.
MACAddressFilter (MAC address filtering setting)
This sets whether or not to enable MAC address filtering.
Note The detailed settings for MAC address filtering are selected
using the optional network interface kit utility software.
>MACAddressFilter
? Off
1
After entering the administrator ID and password, press U or V
repeatedly until >MACAddressFilter appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Press U or V to select whether MAC address filtering is enabled.
Press [OK].
Press [MENU]. The display returns to Ready.
Communication (Select the network interface to use)
Select the interface to be used for network connection.
>Communication
? Standard NIC
1
After entering the administrator ID and password, press U or V
repeatedly until >Communication appears.
2
Press [OK]. A blinking question mark (?) appears.
3
Press U or V to select the desired NIC.
Standard NIC (standard network interface of the printer)
Option NIC (optional network interface kit)
Using the Operation Panel
4
Press [OK].
5
Press [MENU]. The display returns to Ready.
2-53
Restart Network (Restarting the optional network
interface kit)
After all network related settings have been done, restart the network
card of the device. This is mandatory to make the settings effective.
>Restart Network ?
2-54
1
After entering the administrator ID and password, press U or V
repeatedly until >Restart Network appears.
2
Press [OK]. A question mark (?) appears.
3
Press [OK] again. The message Restarting… Please wait.
appears and the network is restarted.
Using the Operation Panel
Device Common (Selecting/Setting the
common device)
Selects/sets all the functions in this printer.
The options available in Device Common are as follows:
• Message Language (Selecting the message language)
• Date Setting (Date and time settings)
• Buzzer (Alarm (Buzzer) setting)
• RAM Disk Mode (Using the RAM disk)
• Error Handling (Error detection setting)
• Timer (Timer setting)
• Sleep Level Set. (Sleep level setting)
• TonerAlert Level (Setting for the alert level for toner addition)
Device Common
>
1
Press [MENU].
2
Press U or V repeatedly until Device Common > appears.
Message Language (Selecting the message
language)
You can select the language of the message display by following the
procedure given below. You can optionally download messages in other
languages. Contact your service technician for information.
1
2
>Message Language
? English
Press Z while Device Common > is displayed.
Press U or V repeatedly until >Message Language appears. The
default message language is English.
3
To change the language, press [OK]. A blinking question mark (?)
appears.
4
Press U or V. The display cycles through the available selection in
the following order:
English
Français
Deutsch
Italiano
Nederlands
Español
Русский
Português
5
6
Using the Operation Panel
Press [OK].
Press [MENU]. The display returns to Ready.
2-55
Date Setting (Date and time settings)
Set the date and time.
The date and time settings consist of the following items:
• ID (Administrator ID input)
• Password (Administrator Password input)
• Date (date setting)
• Time (time setting)
• Date Format (date format selection)
• Time Zone (time difference setting)
• Summer Time (summer time setting)
>Date Setting
>
1
Press Z while Device Common > is displayed.
2
Press U or V repeatedly until >Date Setting > appears.
ID (Administrator ID input)
To use the Date settings, you must enter an administrator ID. For
information on how to set the administrator ID, refer to Administrator
(Administrator settings) on page 2-81.
ID
_
1
Press Z while >Date Setting > is displayed.
2
The message display shows ID and a blinking cursor (_).
3
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. Enter the specified ID. Use Y and Z to move the
cursor right and left. Enter an ID consisting of between 1 and 16
numbers.
4
Press [OK]. Proceed to the next step Password (Administrator
Password input).
Password (Administrator Password input)
To set up the Date settings, you must enter an administrator ID and
administrator password. For information on how to set the administrator
password, refer to Administrator (Administrator settings) on page 281.
Password
_
1
Once you have entered the correct ID in the previous step (ID
(Administrator ID input)), the message display shows Password
(Administrator password input) and a blinking cursor (_).
2
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. Enter the specified password. Use Y and Z to move
the cursor right and left. Enter a password consisting of between 0 (no
settings) and 16 numbers.
Note If you enter the incorrect administrator ID or password,
the message Wrong ID or Wrong Password appears and
the input screen then reappears. Re-enter the ID or password
correctly.
2-56
Using the Operation Panel
3
Press [OK]. The Date settings screen appears.
Date (date setting)
>>Date (Year/Mon/Day)
2013 / 01 / 01
1
After entering the administrator ID and password, press U or V
repeatedly until >>Date (Year/Mon/Day) appears.
2
Press [OK]. A blinking cursor (_) appears.
3
Use the arrow keys to set the year, month, and day. Press U or V to
increase or decrease, respectively, the value at the blinking cursor.
Use Y and Z to move the cursor right and left.
Note The order in which the year, month, and day appear varies
depending on the Date Format (date format selection) on
page 2-57.
4
5
Press [OK].
Press [MENU]. The display returns to Ready.
Time (time setting)
>>Time (Hour:Min:Sec)
11 : 19 : 21
1
After entering the administrator ID and password, press U or V
repeatedly until >>Time (Hour:Min:Sec) appears.
2
Press [OK]. A blinking cursor (_) appears.
3
Use the arrow keys to set the hour, minute, and second. Press U or
V to increase or decrease, respectively, the value at the blinking
cursor. Use Y and Z to move the cursor right and left.
4
5
Press [OK].
Press [MENU]. The display returns to Ready.
Date Format (date format selection)
One of three formats can be selected for the date format.
>>Date Format
? Month/Day/Year
1
After entering the administrator ID and password, press U or V
repeatedly until >>Date Format appears.
2
Press [OK]. A blinking question mark (?) appears.
3
Press U or V to select Date Format. The following date formats
can be selected:
Month/Day/Year
Day/Month/Year
Year/Month/Day
4
5
Using the Operation Panel
Press [OK].
Press [MENU]. The display returns to Ready.
2-57
Time Zone (time difference setting)
Set the time difference from GMT.
>>Time zone
? -05:00 Estn Time
1
After entering the administrator ID and password, press U or V
repeatedly until >>Time zone appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Press U or V to select the location.
Press [OK].
Press [MENU]. The display returns to Ready.
Summer Time (summer time setting)
Set summer time.
>>Summer Time
? Off
1
After entering the administrator ID and password, press U or V
repeatedly until >>Summer Time appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Press U or V to select whether the summer time is enabled.
Press [OK].
Press [MENU]. The display returns to Ready.
Buzzer (Alarm (Buzzer) setting)
This function uses tones to notify the user of printer operations and the
printer status. This setting is useful, for example, when the printer is
located some distance from the user.
The options available in Buzzer are as follows:
• Key Confirm. (Key confirmation tone setting)
• Job End (Job completed tone setting)
• Ready (Preparation completed tone setting)
• Error (Error tone setting)
>Buzzer
>
1
Press Z while Device Common > is displayed.
2
Press U or V repeatedly until >Buzzer > appears.
Key Confirm. (Key confirmation tone setting)
When On is selected in this setting, a tone sounds each time a key is
used. The default setting is On.
1
2
2-58
Press Z while >Buzzer > is displayed.
Press U or V repeatedly until >>Key Confirmation appears.
Using the Operation Panel
>>Key Confirmation
? On
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
Press [OK].
Press [MENU]. The display returns to Ready.
Job End (Job completed tone setting)
When On is selected in this setting, a tone sounds when printing ends.
The default setting is Off.
>>Job End
? Off
1
2
Press Z while >Buzzer > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
Press U or V repeatedly until >>Job End appears.
Press [OK].
Press [MENU]. The display returns to Ready.
Ready (Preparation completed tone setting)
When On is selected in this setting, a tone sounds when print preparation
has been completed. The default setting is Off.
>>Ready
? Off
1
2
Press Z while >Buzzer > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
Press U or V repeatedly until >>Ready appears.
Press [OK].
Press [MENU]. The display returns to Ready.
Error (Error tone setting)
When On is selected in this setting, a tone sounds when a problem such
as running out of paper or a paper jam occurs during printing. The
default setting is On.
>>Error
? On
Using the Operation Panel
1
2
Press Z while >Buzzer > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
Press U or V repeatedly until >>Error appears.
Press [OK].
Press [MENU]. The display returns to Ready.
2-59
RAM Disk Mode (Using the RAM disk)
The RAM disk is a memory space shared within the printer memory that
can temporarily store print jobs. The stored print job can then be used to
print multiple copies of the job reducing the total amount of time required
to print the whole job.
To use the RAM disk, activate and enter the desired size of the RAM disk
in the manner described below. The maximum RAM disk size can be
calculated as follows:
When the RAM disk is activated = The maximum RAM disk size is
16 MB (when no options are attached)
When the optional memory is installed = The maximum RAM disk size is
1/2 of the total optional memory installed
To activate RAM disk in the printer's memory, first you must set the RAM
disk mode to On and set the desired data size for the RAM disk as
described in the following section. This allows you to perform the
following operations on the RAM disk.
Note The RAM disk is an allocated part of the printer’s memory.
IMPORTANT The RAM disk stores data only temporarily. When the
printer is reset or turned off, the stored data will be erased.
The RAM disk is allocated from the printer memory available to users.
If the size of the RAM disk is set too large, the printing speed may
decrease or the memory may become insufficient.
>RAM Disk Mode >
? On
1
2
Press Z while Device Common > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
Press U or V repeatedly until >RAM Disk Mode > appears.
Press [OK].
Press [MENU]. The display returns to Ready.
RAM Disk Size (Setting the RAM disk size)
Use this procedure to set the amount of memory used for the RAM disk.
IMPORTANT The RAM Disk Size menu option only appears when
RAM Disk Mode is set to On.
>>RAM Disk Size
016 MByte
1
Press Z while >RAM Disk Mode
2
Press [OK]. The message display shows a blinking cursor (_). Press
U or V to display the desired size. Use Y and Z to move the cursor
right and left.
On > is displayed.
This range varies depending on the total memory size of the printer.
3
4
2-60
When the desired RAM disk size is displayed, press [OK].
Press [MENU]. The display returns to Ready. Turn the printer off and
then on again. The selected RAM disk size is activated after the
printer is restarted.
Using the Operation Panel
Error Handling (Error detection setting)
This specifies the settings for the detection methods used for duplex
printing errors and for paper size and paper type errors when the paper
source is fixed.
The options available in Error Handling are as follows:
• Duplex (Duplex printing error detection setting)
• Paper Mismatch (Detection settings for paper size/type errors when
the paper source is fixed)
• MP Tray Empty (Warning when the MP tray is empty)
>Error Handling
>
1
Press Z while Device Common > is displayed.
2
Press U or V repeatedly until >Error Handling > appears.
Duplex (Duplex printing error detection setting)
If the error detection setting for duplex printing has been turned On, and
you attempt to print onto a paper size and paper type that cannot be
used for duplex printing, the Duplex disabled Press GO error
message will be displayed and printing will stop.
On
• To print onto one-side of the paper only when this message
is displayed, press [GO].
• Press [Cancel] to cancel the printing itself.
Off
>>Duplex
? On
• To print onto one-side of the paper.
1
2
Press Z while >Error Handling > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
Press U or V repeatedly until >>Duplex appears.
Press [OK].
Press [MENU]. The display returns to Ready.
Paper Mismatch (Detection settings for paper size/type errors
when the paper source is fixed)
Turn this setting to Off if you want to continue printing even if the paper
size or type you specified is different from the fixed paper source, or turn
it to On to have the paper feed error displayed.
>>Paper Mismatch
? On
Using the Operation Panel
1
2
Press Z while >Error Handling > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
Select On or Off using U or V.
Press U or V repeatedly until >>Paper Mismatch appears.
2-61
5
6
Press [OK].
Press [MENU]. The display returns to Ready.
MP Tray Empty (Warning when the MP tray is empty)
Turn this setting to On if you want the error displayed when the MP tray is
configured as the default paper source, and there is no paper in the MP
tray, or turn it to Off not to have the error displayed.
The setting On enables the paper-empty message to display when the
MP tray is empty.
>>MP Tray Empty
? On
1
2
Press Z while >Error Handling > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
Select On or Off using U or V.
5
6
Press [OK].
Press U or V repeatedly until >>MP Tray Empty appears.
Press [MENU]. The display returns to Ready.
Timer (Timer setting)
This specifies timer-related settings such as the automatic form-feed
timeout and the timeout settings for Sleep timer.
The options available in Timer are as follows:
• ID (Administrator ID input)
• Password (Administrator Password input)
• Auto Panel Reset (Auto panel reset settings)
• Panel Reset Timer (Setting the panel reset timer)
• Low Power Timer (Low Power Mode timer timeout time)
• Sleep Timer (Sleep timer timeout time)
• Auto Error Clear (Auto error clear setting)
• Error Clear Timer (Setting the error clear time)
• Form Feed Time Out (Automatic form feed timeout setting)
>Timer
>
1
Press Z while Device Common > is displayed.
2
Press U or V repeatedly until >Timer > appears.
ID (Administrator ID input)
To use the Timer settings, you must enter an administrator ID. For
information on how to set the administrator ID, refer to Administrator
(Administrator settings) on page 2-81.
ID
_
2-62
1
Press Z while >Timer > is displayed.
2
The message display shows ID and a blinking cursor (_).
Using the Operation Panel
3
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. Enter the specified ID. Use Y and Z to move the
cursor right and left. Enter an ID consisting of between 1 and 16
numbers.
4
Press [OK]. Proceed to the next step Password (Administrator
Password input).
Password (Administrator Password input)
To set up the Timer settings, you must enter an administrator ID and
administrator password. For information on how to set the administrator
password, refer to Administrator (Administrator settings) on page 281.
Password
_
1
Once you have entered the correct ID in the previous step (ID
(Administrator ID input)), the message display shows Password
(Administrator password input) and a blinking cursor (_).
2
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. Enter the specified password. Use Y and Z to move
the cursor right and left. Enter a password consisting of between 0 (no
settings) and 16 numbers.
Note If you enter the incorrect administrator ID or password,
the message Wrong ID or Wrong Password appears and
the input screen then reappears. Re-enter the ID or password
correctly.
3
Press [OK]. The Timer settings screen appears.
Auto Panel Reset (Auto panel reset settings)
The Auto Panel Reset function automatically restores the default
settings if the panel is not used for a set time. The default setting is On.
For setting the time until the panel is reset, refer to the next section
Panel Reset Timer (Setting the panel reset timer).
>>Auto Panel Reset
? On
1
After entering the administrator ID and password, press U or V
repeatedly until >>Auto Panel Reset appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Select On or Off using U or V.
Press [OK].
Press [MENU]. The display returns to Ready.
Panel Reset Timer (Setting the panel reset timer)
When Auto Panel Reset is set to On, this sets the time until the panel is
automatically reset after the user stops using the panel. The default time
is 90 seconds.
1
Using the Operation Panel
After entering the administrator ID and password, press U or V
repeatedly until >>Panel Reset Timer appears.
2-63
>>Panel Reset Timer
090sec.
2
Press [OK]. The message display shows a blinking cursor (_).
3
Press U or V to increase or decrease the value at the blinking cursor
and set the desired time. The time must be set between 005 and 495
seconds, in 5-second increments. Use Y and Z to move the cursor
right and left.
4
5
Press [OK].
Press [MENU]. The display returns to Ready.
Low Power Timer (Low Power Mode timer timeout time)
You can adjust the length of time the printer waits before entering Low
Power Mode in the absence of a print job.
The printer reverts to normal operation mode when the printer receives a
print job or [GO] is pressed on the operation panel. The default time is
1 minute.
>>Low Power Timer
005 min.
1
After entering the administrator ID and password, press U or V
repeatedly until >>Low Power Timer appears.
2
To change the timeout time, press [OK]. A blinking cursor (_)
appears.
3
Press U or V to increase or decrease the value at the blinking cursor
and set the desired time. The timer can be set between 1 and
120 min (for Europe) or 1 and 240 min (except for Europe). Use Y
and Z to move the cursor right and left.
4
5
Press [OK].
Press [MENU]. The display returns to Ready.
Sleep Timer (Sleep timer timeout time)
You can adjust the length of time the printer waits before entering Auto
Sleep in the absence of data.
The printer reverts to normal operation mode when the printer receives a
print job, or [GO] is pressed on the operation panel. The default time is
15 minutes (for Europe) and 1 minute (except for Europe).
Note Calibration is automatically executed before the printer
reverts to normal operation mode.
>>Sleep Timer
015 min.
2-64
1
After entering the administrator ID and password, press U or V
repeatedly until >>Sleep Timer appears.
2
To change the timeout time, press [OK]. A blinking cursor (_)
appears.
3
Press U or V to increase or decrease the value at the blinking cursor
and set the desired time. The timer can be set between 1 and
120 min (for Europe) or 1 and 240 min (except for Europe). Use Y
and Z to move the cursor right and left.
4
Press [OK].
Using the Operation Panel
5
Press [MENU]. The display returns to Ready.
Auto Error Clear (Auto error clear setting)
If an error that still allows you to continue printing occurs, the next
received data is automatically printed after a set period of time elapses.
For example, if the printer is shared over a network as a network printer
and one person causes one of the above errors, after the set period of
time elapses, the data sent from the next person is printed. The default
setting is Off (Auto Error Clear disabled).
The auto clear errors are:
• Memory overflow Press GO
• KPDL error
## Press GO
• RAM disk error## Press GO
• Duplex disabled Press GO
• Job not stored Press GO
• No multi copies Press GO
• USB memory error ## Press GO
For setting the auto error clear recovery time, refer to the next section
Error Clear Timer (Setting the error clear time).
>>Auto Error Clear
? Off
1
2
Press Z while >Timer > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select On or Off using U or V.
Press U or V repeatedly until >>Auto Error Clear appears.
Press [OK].
Press [MENU]. The display returns to Ready.
Error Clear Timer (Setting the error clear time)
If Auto Error Clear is set to On and a non-fatal error (an error that allows
printing to continue) occurs, this setting specifies the time until the error
is recovered and printing resumes.
>>Error Clear Timer
030sec.
Using the Operation Panel
1
Press Z while >Timer > is displayed.
2
Press U or V repeatedly until >>Error Clear Timer appears.
3
Press [OK]. A blinking cursor (_) appears.
4
Press U or V to increase or decrease the value at the blinking cursor
and set the desired time. The time must be set between 005 and 495
seconds, in 5-second increments. You can use Y and Z to move the
cursor right and left.
5
6
Press [OK].
Press [MENU]. The display returns to Ready.
2-65
Form Feed Time Out (Automatic form feed timeout setting)
If the printer receives no data for a certain period, it will time out and
release the current interface. It prints whatever data it has in its buffer
and feeds out the page. The default form feed timeout time is 30
seconds.
>>Form Feed Time Out
005sec.
1
2
Press Z while >Timer > is displayed.
3
Press [OK]. A blinking cursor (_) appears.
4
Press U or V to increase or decrease the value at the blinking cursor
and set the desired time. The timeout time can be between 5 and 495
seconds, in 5-second increments. Use Y and Z to move the cursor
right and left.
5
6
Press [OK].
Press U or V repeatedly until >>Form Feed Time Out appears.
Press [MENU]. The display returns to Ready.
Sleep Level Set. (Sleep level setting)
For Europe
This sets whether or not the machine enters sleep mode when
connected to a network.
• ID (Administrator ID input)
• Password (Administrator Password input)
• Network (Setting for entering sleep mode when connected to a
network)
• USB Cable (Setting for entering sleep mode when connected to a
USB)
• RAM Disk (Setting for entering sleep mode when using the RAM disk)
>Sleep Level Set.
>
1
Press Z while Device Common > is displayed.
2
Press U or V repeatedly until >Sleep Level Set. > appears.
ID (Administrator ID input)
To use the Sleep Level settings, you must enter an administrator ID. For
information on how to set the administrator ID, refer to Administrator
(Administrator settings) on page 2-81.
ID
_
2-66
1
Press Z while >Sleep Level Set. > is displayed.
2
The message display shows ID and a blinking cursor (_).
3
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. Enter the specified ID. Use Y and Z to move the
cursor right and left. Enter an ID consisting of between 1 and 16
numbers.
Using the Operation Panel
4
Press [OK]. Proceed to the next step Password (Administrator
Password input).
Password (Administrator Password input)
To set up the Sleep Level settings, you must enter an administrator ID
and administrator password. For information on how to set the
administrator password, refer to Administrator (Administrator
settings) on page 2-81.
Password
_
1
Once you have entered the correct ID in the previous step (ID
(Administrator ID input)), the message display shows Password
(Administrator password input) and a blinking cursor (_).
2
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. Enter the specified password. Use Y and Z to move
the cursor right and left. Enter a password consisting of between 0 (no
settings) and 16 numbers.
Note If you enter the incorrect administrator ID or password,
the message Wrong ID or Wrong Password appears and
the input screen then reappears. Re-enter the ID or password
correctly.
3
Press [OK]. The Sleep Level settings screen appears.
Network (Setting for entering sleep mode when connected to a
network)
This sets whether or not the machine enters sleep mode when
connected to a network.
>>Network
? On
1
After entering the administrator ID and password, press U or V
repeatedly until >>Network appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Select On or Off using U or V.
Press [OK].
Press [MENU]. The display returns to Ready.
USB Cable (Setting for entering sleep mode when connected to a
USB)
This sets whether or not the machine enters sleep mode when
connected to a USB.
>>USB Cable
? On
Using the Operation Panel
1
After entering the administrator ID and password, press U or V
repeatedly until >>USB Cable appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Select On or Off using U or V.
Press [OK].
Press [MENU]. The display returns to Ready.
2-67
RAM Disk (Setting for entering sleep mode when using the RAM
disk)
This sets whether or not the machine enters sleep mode when using the
RAM disk.
>>RAM Disk
? On
1
After entering the administrator ID and password, press U or V
repeatedly until >>RAM Disk appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Select On or Off using U or V.
Press [OK].
Press [MENU]. The display returns to Ready.
Except for Europe
Select the sleep level.
The options available in Sleep Level Set. are as follows:
• ID (Administrator ID input)
• Password (Administrator Password input)
• Sleep Level (Sleep level setting)
• Network (Setting for entering energy-saving mode when connected to
a network)
• USB Cable (Setting for entering energy-saving mode when connected
to a USB)
• RAM Disk (Setting for entering energy-saving mode when using the
RAM disk)
Note Network, USB Cable and RAM Disk are only displayed
when Sleep Level is set to Energy Saver.
>Sleep Level Set.
>
1
Press Z while Device Common > is displayed.
2
Press U or V repeatedly until >Sleep Level Set. > appears.
ID (Administrator ID input)
To use the Sleep Level settings, you must enter an administrator ID. For
information on how to set the administrator ID, refer to Administrator
(Administrator settings) on page 2-81.
ID
_
2-68
1
Press Z while >Sleep Level Set. > is displayed.
2
The message display shows ID and a blinking cursor (_).
3
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. Enter the specified ID. Use Y and Z to move the
cursor right and left. Enter an ID consisting of between 1 and 16
numbers.
4
Press [OK]. Proceed to the next step Password (Administrator
Password input).
Using the Operation Panel
Password (Administrator Password input)
To set up the Sleep Level settings, you must enter an administrator ID
and administrator password. For information on how to set the
administrator password, refer to Administrator (Administrator
settings) on page 2-81.
Password
_
1
Once you have entered the correct ID in the previous step (ID
(Administrator ID input)), the message display shows Password
(Administrator password input) and a blinking cursor (_).
2
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. Enter the specified password. Use Y and Z to move
the cursor right and left. Enter a password consisting of between 0 (no
settings) and 16 numbers.
Note If you enter the incorrect administrator ID or password,
the message Wrong ID or Wrong Password appears and
the input screen then reappears. Re-enter the ID or password
correctly.
3
Press [OK]. The Sleep Level settings screen appears.
Sleep Level (Sleep level setting)
There are two sleep modes with different levels of sleep: Quick
Recovery and Energy Saver.
Quick Recovery Mode: The recovery from the sleep mode is faster than
when using Energy Saver mode.
Energy Saver Mode: This makes it possible to reduce energy
consumption even further than with Quick Recovery mode. With Energy
Saver mode, you can set whether to enable the Energy Saver mode for
each separate function.
IMPORTANT Cautions when setting the Energy Saver mode
• The data stored on the RAM disk is deleted when the machine goes
into Energy Saver mode.
• The machine will not recover from Energy Saver mode if printing data is
received from a computer via a USB cable.
• An ID card is not recognized when in Energy Saver mode.
Note For information on the Quick Recovery mode and Energy
Saver mode, refer to the Connecting and Printing section in the
Operation Guide.
Sleep Level Set. menu is not displayed when the optional network
interface kit (IB-50) or wireless network interface kit (IB-51) has
been installed.
>>Sleep Level
? Energy Saver
Using the Operation Panel
1
After entering the administrator ID and password, press U or V
repeatedly until >>Sleep Level appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Press U or V to select Quick Recovery or Energy Saver.
Press [OK].
Press [MENU]. The display returns to Ready.
2-69
Network (Setting for entering energy-saving mode when connected
to a network)
This sets whether or not the machine enters Energy Saver mode when
connected to a network.
>>Network
? On
1
After entering the administrator ID and password, press U or V
repeatedly until >>Network appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Select On or Off using U or V.
Press [OK].
Press [MENU]. The display returns to Ready.
USB Cable (Setting for entering energy-saving mode when
connected to a USB)
This sets whether or not the machine enters sleep mode when
connected to a USB.
>>USB Cable
? On
1
After entering the administrator ID and password, press U or V
repeatedly until >>USB Cable appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Select On or Off using U or V.
Press [OK].
Press [MENU]. The display returns to Ready.
RAM Disk (Setting for entering energy-saving mode when using the
RAM disk)
This sets whether or not the machine enters sleep mode when using the
RAM disk.
>>RAM Disk
? On
2-70
1
After entering the administrator ID and password, press U or V
repeatedly until >>RAM Disk appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Select On or Off using U or V.
Press [OK].
Press [MENU]. The display returns to Ready.
Using the Operation Panel
TonerAlert Level (Setting for the alert level for toner
addition)
This sets the toner addition alert level displayed on the status monitor.
The options available in TonerAlert Level are as follows:
• ID (Administrator ID input)
• Password (Administrator Password input)
• Off/On
• TonerAlert Level (Setting for the alert level for toner addition)
>TonerAlert Level
>
1
Press Z while Device Common > is displayed.
2
Press U or V repeatedly until >TonerAlert Level > appears.
ID (Administrator ID input)
To use the TonerAlert Level settings, you must enter an administrator ID.
For information on how to set the administrator ID, refer to
Administrator (Administrator settings) on page 2-81.
ID
_
1
Press Z while >TonerAlert Level > is displayed.
2
The message display shows ID and a blinking cursor (_).
3
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. Enter the specified ID. Use Y and Z to move the
cursor right and left. Enter an ID consisting of between 1 and 16
numbers.
4
Press [OK]. Proceed to the next step Password (Administrator
Password input).
Password (Administrator Password input)
To set up the TonerAlert Level settings, you must enter an administrator
ID and administrator password. For information on how to set the
administrator password, refer to Administrator (Administrator
settings) on page 2-81.
Password
_
1
Once you have entered the correct ID in the previous step (ID
(Administrator ID input)), the message display shows Password
(Administrator password input) and a blinking cursor (_).
2
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. Enter the specified password. Use Y and Z to move
the cursor right and left. Enter a password consisting of between 0 (no
settings) and 16 numbers.
Note If you enter the incorrect administrator ID or password,
the message Wrong ID or Wrong Password appears and
the input screen then reappears. Re-enter the ID or password
correctly.
3
Using the Operation Panel
Press [OK]. The TonerAlert Level settings screen appears.
2-71
Off/On (Setting toner addition notifications)
Select whether Toner Alert Level is enabled.
>>Off/On
? Off
1
After entering the administrator ID and password, press U or V
repeatedly until >>Off/On appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Select On or Off using U or V.
Press [OK].
Press [MENU]. The display returns to Ready.
TonerAlert Level (Setting for the alert level for toner addition)
This sets the level at which toner addition alerts will be displayed.
>>TonerAlert Level
005 %
2-72
1
After entering the administrator ID and password, press U or V
repeatedly until >>TonerAlert Level appears.
2
Press [OK]. A blinking cursor (_) appears.
3
Press U or V to increase or decrease the value at the blinking cursor
and set the level at which an alert will be displayed. The setting is
possible between 005 and 100%. Use Y and Z to move the cursor
right and left.
4
5
Press [OK].
Press [MENU]. The display returns to Ready.
Using the Operation Panel
Security
The security functions can be set up to protect printer operation and the
print data.
The options available in Security are as follows:
• ID (Administrator ID input)
• Password (Administrator Password input)
• I/F Block (Interface (external device) block setting)
• WSD-PRINT (WSD-PRINT setting)
• Enhanced WSD (Enhanced WSD setting)
• EnhancedWSD(SSL) (Enhanced WSD (SSL) setting)
• IPP (IPP setting)
• SSL Server (SSL Server setting)
• IPSec (IPSec setting)
• LAN Interface (LAN Interface setting)
• Security Level (Security Level setting)
Note When Embedded Web Server RX is used, network
parameters and security settings can be conveniently
changed and checked from your PC. For more information,
refer to the Embedded Web Server RX User Guide.
Security
>
1
Press [MENU].
2
Press U or V repeatedly until Security > appears.
ID (Administrator ID input)
To use the Security function, you must enter an administrator ID. For
information on how to set the administrator ID, refer to Administrator
(Administrator settings) on page 2-81.
ID
_
1
Press Z while Security > is displayed.
2
The message display shows ID and a blinking cursor (_).
3
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. Enter the specified ID. Use Y and Z to move the
cursor right and left. Enter an ID consisting of between 1 and 16
numbers.
4
Press [OK]. Proceed to the next step Password (Administrator
Password input).
Password (Administrator Password input)
To set up the Security functions, you must enter an administrator ID and
administrator password. For information on how to set the administrator
password, refer to Administrator (Administrator settings) on page 281.
Using the Operation Panel
2-73
Password
_
1
Once you have entered the correct ID in the previous step (ID
(Administrator ID input)), the message display shows Password
(Administrator password input) and a blinking cursor (_).
2
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. Enter the specified password. Use Y and Z to move
the cursor right and left. Enter a password consisting of between 0 (no
settings) and 16 numbers.
Note If you enter the incorrect administrator ID or password,
the message Wrong ID or Wrong Password appears and
the input screen then reappears. Re-enter the ID or password
correctly.
3
Press [OK]. The Security screen appears.
I/F Block (Interface (external device) block setting)
You can use this to lock and thereby protect the interface. The options
available in Interface Block are as follows:
• USB Host (USB memory slot setting)
• USB Device (USB interface setting)
• Option I/F (Network interface card setting)
• USB Storage (USB memory setting)
>I/F Block
>
1
After entering the administrator ID and password, press U or V
repeatedly until >I/F Block > appears.
USB Host (USB memory slot setting)
This locks and protects the USB memory slot (USB host). The default
setting is Unblock.
>>USB Host
? Unblock
1
2
Press Z while >I/F Block > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select Block or Unblock using U or V.
Press U or V repeatedly until >>USB Host appears.
Press [OK].
Press [MENU]. The display returns to Ready.
USB Device (USB interface setting)
This locks and protects the USB interface. The default setting is
Unblock.
>>USB Device
? Unblock
2-74
1
2
Press Z while >I/F Block > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
Press U or V repeatedly until >>USB Device appears.
Using the Operation Panel
4
5
6
Select Block or Unblock using U or V.
Press [OK].
Press [MENU]. The display returns to Ready.
Option I/F (Network interface card setting)
This locks and protects the network interface card (NIC). The default
setting is Unblock.
Note Option I/F is displayed only when the optional network
interface is installed on the printer.
>>Option I/F
? Unblock
1
2
Press Z while >I/F Block > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
Select Block or Unblock using U or V.
5
6
Press [OK].
Press U or V repeatedly until >>Option I/F appears.
Press [MENU]. The display returns to Ready.
USB Storage (USB memory setting)
This blocks and protects the USB storage (USB memory). The default
setting is Unblock.
>>USB Storage
? Unblock
1
2
Press Z while >I/F Block > is displayed.
3
Press [OK]. A blinking question mark (?) appears.
4
5
6
Select Block or Unblock using U or V.
Press U or V repeatedly until >>USB Storage appears.
Press [OK].
Press [MENU]. The display returns to Ready.
WSD-PRINT (WSD-PRINT setting)
Select whether or not to use WSD Print. The default setting is On.
>WSD-PRINT
? On
Using the Operation Panel
1
After entering the administrator ID and password, press U or V
repeatedly until >WSD-PRINT appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Press U or V to select whether WSD-PRINT is enabled.
Press [OK].
Press [MENU]. The display returns to Ready.
2-75
Enhanced WSD (Enhanced WSD setting)
Set whether to use our proprietary web services. Network driver use this
Enhanced WSD Web service. The default setting is On.
>Enhanced WSD
? On
1
After entering the administrator ID and password, press U or V
repeatedly until >Enhanced WSD appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Press U or V to select whether Enhanced WSD is enabled.
Press [OK].
Press [MENU]. The display returns to Ready.
EnhancedWSD(SSL) (Enhanced WSD (SSL) setting)
Set whether to use our proprietary web services over SSL. SSL must be
set to On in SSL Server (SSL Server setting) on page 2-77. The default
setting is On.
>EnhancedWSD(SSL)
? On
1
After entering the administrator ID and password, press U or V
repeatedly until >EnhancedWSD(SSL) appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Press U or V to select whether Enhanced WSD (SSL) is enabled.
Press [OK].
Press [MENU]. The display returns to Ready.
IPP (IPP setting)
IPP (Internet Printing Protocol) is a standard that uses TCP/IP networks
such as the Internet to enable print jobs to be sent between remote
computers and printers.
IPP is an extension of the HTTP protocol used to view websites and
enables printing to be carried out via routers on printers in remote
locations. It also supports the HTTP authentication mechanisms along
with SSL server and client authentication as well as encryption.
The default setting is On.
Note Check with your network administrator when selecting
network settings.
>IPP
>IPP
? Off
2-76
1
After entering the administrator ID and password, press U or V
repeatedly until >IPP appears.
2
Press [OK]. A blinking question mark (?) appears.
3
Select On or Off using U or V.
Using the Operation Panel
4
5
Press [OK].
Press [MENU]. The display returns to Ready.
SSL Server (SSL Server setting)
SSL (Secure Sockets Layer) refers to a protocol used to encrypt
information sent and received over a network. SSL can currently be used
to encrypt data such as the WWW or FTP files widely used on the
Internet so that privacy-related information, credit card numbers,
corporate secrets and other confidential information can be sent and
received safely.
SSL servers use this protocol to authenticate servers and clients.
The default setting is On.
Note Check with your network administrator when selecting
network settings.
>SSL Server
>
>SSL Server
? Off
>
1
After entering the administrator ID and password, press U or V
repeatedly until >SSL Server > appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Select On or Off using U or V.
Press [OK].
Press [MENU]. The display returns to Ready.
DES (SSL Server DES setting)
DES (Data Encryption Standard) is a typical symmetric-key
cryptographic algorithm that divides data in to 64-bit blocks and then
encrypts each block using a 56-bit key.
Note Symmetric-key cryptography, because it uses the same
key for both encryption and decryption, uses the same key in both
directions when encrypted data is exchanged. Accordingly, to
prevent the key from being divulged, key transfer and storage
must be very strictly managed.
The default setting is Off.
>>DES
? Off
Using the Operation Panel
1
Press Z while >SSL Server
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Select On or Off using U or V.
On > is displayed. >>DES appears.
Press [OK].
Press [MENU]. The display returns to Ready.
2-77
3DES (SSL Server 3DES setting)
3DES (Triple Data Encryption Standard) is a high level of encryption in
which DES encryption is repeated threefold.
The default setting is On.
>>3DES
? On
1
Press Z while >SSL Server
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Select On or Off using U or V.
On > is displayed. >>3DES appears.
Press [OK].
Press [MENU]. The display returns to Ready.
AES (SSL Server AES setting)
AES (Advanced Encryption Standard) was developed to replace DES as
the standard encryption as the safety of DES has declined. AES is a
block encryption system that uses 128-bit blocks and an SPN structure
(a typical structure for repeated encryption) with three selectable key
lengths of 128, 192 and 256 bits.
The default setting is On.
>>AES
? On
1
Press Z while >SSL Server
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Select On or Off using U or V.
On > is displayed. >>AES appears.
Press [OK].
Press [MENU]. The display returns to Ready.
IPP over SSL (SSL Server IPP over SSL setting)
IPP over SSL is an encryption function that uses SSL for
communications between users and servers in network printing. To use
IPP over SSL, both server and client must support the protocol.
The default setting is On.
>>IPP over SSL
? Off
2-78
1
Press Z while >SSL Server On > is displayed. >>IPP over SSL
appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Select On or Off using U or V.
Press [OK].
Press [MENU]. The display returns to Ready.
Using the Operation Panel
HTTPS (SSL Server HTTPS setting)
HTTPS (HyperText Transfer Protocol Secure) is a protocol that adds
SSL data encryption, message authentication and a digital signature
function to the HTTP protocol used for data transfer between WWW
servers and clients.
S-HTTP is a similar protocol, but HTTPS differs in that it uses SSL.
The default setting is On.
>>HTTPS
? On
1
Press Z while >SSL Server On > is displayed. >>HTTPS appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Select On or Off using U or V.
Press [OK].
Press [MENU]. The display returns to Ready.
IPSec (IPSec setting)
IPSec (IP Security Protocol) is a security protocol adopted as the
standard by the IETF for authentication and encryption in the third
network layer (IP layer).
It can be used with both IPv4 and IPv6.
Note IPv4 uses 32-bit IP addresses and IPv6 uses 128-bit IP
addresses.
The default setting is Off.
Note Check with your network administrator when selecting
network settings.
>IPSec
>IPSec
? Off
Using the Operation Panel
1
After entering the administrator ID and password, press U or V
repeatedly until >IPSec appears.
2
Press [OK]. A blinking question mark (?) appears.
3
4
5
Select On or Off using U or V.
Press [OK].
Press [Menu]. The display returns to Ready.
2-79
LAN Interface (LAN Interface setting)
Specify the settings for the LAN interface to be used. The default setting
is Auto.
>LAN Interface
Auto
>LAN Interface
? Auto
1
After entering the administrator ID and password, press U or V
repeatedly until >LAN Interface appears.
2
Press [OK]. A blinking question mark (?) appears.
3
Press U or V to select the desired LAN Interface. The available LAN
Interfaces are as follows:
Auto
10Base-Half
10Base-Full
100Base-Half
100Base-Full
1000Base-T
4
5
Press [OK].
Press [MENU]. The display returns to Ready.
Security Level (Security Level setting)
Security Level is primarily a menu used by service personnel for
maintenance work. There is no need for customers to use this menu.
2-80
Using the Operation Panel
Administrator (Administrator settings)
The Administrator setting is a function that identifies a user who can use
the printer and manage other users.
When using the Security and Optional Network functions, the
administrator ID and password set here are authenticated, and settings
can be specified after they are properly authenticated.
The options available in Admin are as follows:
• ID (Administrator ID input)
• Password (Administrator Password input)
• Change ID (Administrator ID change)
• Change Password (Administrator Password change)
Administrator
>
1
Press [MENU].
2
Press U or V repeatedly until Administrator > appears.
ID (Administrator ID input)
You can use this to set the administrator ID.
Note The default setting is "3500".
ID
_
1
Press Z while Administrator > is displayed.
2
The message display shows ID and a blinking cursor (_).
3
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. Enter the specified ID. Use Y and Z to move the
cursor right and left. Enter an ID consisting of between 1 and 16
digits.
4
Press [OK]. Proceed to the next step Password (Administrator
Password input).
Password (Administrator Password input)
You can use this to set the administrator password.
Note The default setting is "3500".
Password
_
Using the Operation Panel
1
Once you have entered the correct ID in the previous step (ID
(Administrator ID input)), the message display shows Password
(Administrator password input) and a blinking cursor (_).
2-81
2
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. Enter the specified password. Use Y and Z to move
the cursor right and left. Enter a password consisting of between 0
and 16 digits.
Note If you enter the incorrect administrator ID or password,
the Wrong ID or Wrong Password message appears and
the input screen then reappears. Re-enter the ID or password
correctly.
>Change ID
00000001
3
Once you enter the correct ID and password, the Admin (change)
screen appears. (E.g.: Where the administrator ID is 00000001)
Each time you press U or V, the following settings to be changed
appear in succession.
• Change ID
• Change Password
Note If a change is required, refer to the procedures in
Change ID (Administrator ID change) and Change Password
(Administrator Password change) below.
4
Press [OK] again. The administrator ID and password are confirmed.
5
Press [MENU]. The display returns to Ready.
Change ID (Administrator ID change)
You can use this to change the administrator ID.
>Change ID
001
>Change ID
_
OK?
002
2-82
1
In step 3 in Password (Administrator Password input) above, press U
or V while the Admin (Change) screen is displayed until >Change
ID appears. (E.g.: Where the administrator ID is 001)
2
When you press [OK], a blinking cursor (_) appears.
3
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. Enter the ID to be changed. Use Y and Z to move the
cursor right and left. Enter an ID consisting of between 1 and 16
numbers.
4
Press [OK]. A confirmation screen appears. (E.g.: Where the
administrator ID is changed to 002)
5
6
Press [OK]. The new administrator ID is confirmed.
Press [MENU]. The display returns to Ready.
Using the Operation Panel
Change Password (Administrator Password change)
You can use this to change the administrator password.
>Change Password
1
In step 3 in Password (Administrator Password input) above, press U
or V while the Admin (Change) screen is displayed until >Change
Password appears.
IMPORTANT The administrator password is not displayed.
>Change Password
_
OK?
010
Using the Operation Panel
2
Press [OK]. A blinking cursor (_) appears.
3
Press U or V to increase or decrease, respectively, the value at the
blinking cursor. Enter the password to be changed. Use Y and Z to
move the cursor right and left. Enter a password consisting of
between 0 and 16 numbers.
4
Press [OK]. A confirmation screen appears. (E.g.: Where the
administrator password is changed to 010)
5
6
Press [OK]. The new administrator password is confirmed.
Press [MENU]. The display returns to Ready.
2-83
Adjust/Maintenance (Adjust/Maintenance
selection/setting)
Adjust/Maintenance is used to adjust the print quality and to carry out
printer maintenance.
The options available in Adjust/Maintenance are as follows:
• Restart Printer
• Service (for maintenance)
IMPORTANT Service is primarily a menu used by service personnel for maintenance work. There is no need for customers to use this
menu.
Adjust/Maintenance
>
1
Press [MENU].
2
Press U or V repeatedly until Adjust/Maintenance > appears.
Restart Printer
The procedure described below resets the printer’s temporary
conditions, such as the current page orientation, font, etc., set by
commands to their default values. Downloaded fonts and macros are
deleted from the printer’s memory.
>Restart Printer ?
2-84
1
2
Press Z while Adjust/Maintenance > is displayed.
3
Press [OK]. A question mark (?) appears.
4
Press [OK] again. Self test appears while the printer is resetting
itself, followed by Please wait and then Ready.
Press U or V repeatedly until >Restart Printer appears.
Using the Operation Panel
Service (for maintenance)
The options available in Service are as follows:
• Print Status Page (Printing the service status page)
• Print Network Status Page (Printing the network status page)
• Print Op Network Status Page (Printing the option network status
page)
• Print Test Page
• Maintenance (New Maintenance Kit replacement confirmation setting)
• Developer (Initializing the developer unit)
IMPORTANT Service is primarily a menu used by service personnel
for maintenance work. There is no need for customers to use this
menu.
>Service
>
1
Press Z while Adjust/Maintenance > is displayed.
2
Press U or V repeatedly until >Service > appears.
Print Status Page (Printing the service status page)
The service status page contains printer settings information that is more
detailed than the standard status page and is therefore mostly for service
purposes. However, there is a great deal of information on the service
status page that may be useful to you.
>>Print Status Page ?
1
2
Press Z while >Service > is displayed.
3
Press [OK]. A question mark (?) appears.
4
Press [OK] again. Processing appears and a service status page
is printed out.
5
When printing ends, the display returns to Ready.
Press U or V repeatedly until >>Print Status Page appears.
Print Network Status Page (Printing the network status page)
The network status page contains detailed information on the network
settings. This is primarily used for maintenance by service personnel, but
it contains information that may also be useful to you.
1
2
>>Print
Network Status Page?
Using the Operation Panel
Press Z while >Service > is displayed.
Press U or V repeatedly until >>Print Network Status Page
appears.
3
Press [OK]. A question mark (?) appears.
4
Press [OK] again. Processing appears and a network status page
is printed out.
5
When printing ends, the display returns to Ready.
2-85
Print Op Network Status Page (Printing the option network
status page)
The option network status page contains detailed information on the
network settings. This is primarily used for maintenance by service
personnel, but it contains information that may also be useful to you.
>>Print Op
Network Status Page?
1
2
Press Z while >Service > is displayed.
3
Press [OK]. A question mark (?) appears.
4
Press [OK] again. Processing appears and an option network
status page is printed out.
5
When printing ends, the display returns to Ready.
Press U or V repeatedly until >>Print Op Network Status
Page appears.
Print Test Page
The test page is printed to check the effectiveness of printer
adjustments. This is primarily used for maintenance by service
personnel, but it contains information that may also be useful to you.
>>Print Test Page ?
1
Press Z while >Service > is displayed.
2
Press U or V repeatedly until >>Print Test Page appears.
3
Press [OK]. A question mark (?) appears.
4
Press [OK] again. Processing appears and a test page is printed
out.
5
When printing ends, the display returns to Ready.
Maintenance (New Maintenance Kit replacement confirmation
setting)
This specifies the setting for confirmation of replacement with the new
Maintenance Kit (resets the total number of Maintenance Kit print
images). This is primarily used for maintenance by service personnel.
Note The Maintenance menu is displayed only when Replace
MK appears.
>>Maintenance ?
2-86
1
2
Press Z while >Service > is displayed.
3
Press [OK]. A question mark (?) appears.
4
Press [OK] again. The confirmation of replacement with the new
Maintenance Kit is set.
5
When the replacement ends, the display returns to Ready.
Press U or V repeatedly until >>Maintenance appears.
Using the Operation Panel
Developer (Initializing the developer unit)
The replaced developer can be automatically fill up the toner using this
menu when a toner container is installed and the printer is turned on.
This is primarily used for maintenance by service representative.
Using the Operation Panel
2-87
2-88
Using the Operation Panel
3
Option
This chapter explains the options for this printer.
General Information
Expansion Memory Modules
Paper Feeder (PF-100)
Network Interface Kit (IB-50)
Wireless Network Interface Kit (IB-51)
USB Flash Memory
Option
3-2
3-3
3-5
3-5
3-5
3-5
3-1
General Information
The printers have the following options available to satisfy your printing
requirements.
Note Install the memory module before installing the optional
paper feeder (PF-100).
For instructions on installing individual options, refer to the
documentation included with the option. Some options are explained in
the following sections.
USB Flash Memory
Network Interface
Kit (IB-50)
Expansion Memory
Module (DIMM
256/512/1024 MB)
Paper Feeder (PF-100)
Up to two cassettes can
be attached.
3-2
Wireless Network
Interface Kit (IB-51)
Option
Expansion Memory Modules
To expand the printer memory for more complex print jobs and faster
print speed, you can plug in optional memory module (dual in line
memory module) in the memory slot provided on the printer main
controller board. You can select additional memory module from 256,
512, or 1024 MB. The maximum memory size is 1280 MB.
Note The expansion memory should only be installed by your
service technician. We shall not be liable for any damages caused
by improper installation of expansion memory.
Precautions for Handling the Printer's Main
Controller Board and Memory Module
To protect electronic parts, discharge static electricity from your body by
touching a water pipe (faucet) or other large metal object before handling
the memory module. Or, wear an antistatic wrist strap, if possible, when
you install the memory module.
Always hold the main controller board or a memory module by its edges
as shown below to avoid damaging electronic parts.
Correct
Incorrect
Installing the Memory Module
1
2
Option
Turn off the printer and disconnect the power cord and printer cable.
Remove the right cover as shown in the figure.
3-3
3
Remove the fixing tape in case of the first installation. Then, remove
the memory slot cover as shown in the figure.
4
5
Remove the memory module from its package.
Aligning the cutouts of the memory module with the matching keys of
the socket, carefully plug the memory module into the memory
socket until it clicks in place. Then, push down the memory module
to secure.
CAUTION Before inserting a memory module in the printer,
make sure that the printer is switched off.
6
7
Push down the memory module to secure.
Reinstall the memory slot cover and the right cover.
Removing a Memory Module
To remove a memory module, remove the right cover and the memory
slot cover from the printer. Then, carefully push out the two socket
clamps. Ease the memory module out of the socket to remove.
Verifying the expanded memory
To verify that the memory module is working properly, test it by printing a
status page.
3-4
Option
Paper Feeder (PF-100)
The PF-100 allows you to add two more paper cassette to the bottom of
the printer for continuous feeding of a large volume of paper. Each paper
cassette can hold up to approximately 250 sheets of ISO A4, ISO A5,
JIS B5, Letter, or Legal size (80g/m2) paper. This feeder is attached at
the bottom of the printer as shown on the left.
CAUTION Before attaching the PF-100 to the printer, make
sure that the printer is switched off.
Network Interface Kit (IB-50)
The network interface kit is a high-speed interface for communications
speeds of 1 gigabit per second. In addition to the TCP/IP and NetBEUI
supported by the machine's standard network interface, it also supports
IPX/SPX and Apple Talk, so network printing becomes possible in
various environments, including Windows, Macintosh, UNIX and
Netware. For details, refer to IB-50 User's Manual.
Wireless Network Interface Kit (IB-51)
This is a wireless network interface kit which supports the wireless
network specifications IEEE802.11n (Max 300 Mbps) and 11 g/b.
With the utilities supplied, settings are possible for a variety of OS and
network protocols. For details, refer to IB-51 User's Manual.
USB Flash Memory
See your dealer for purchasing information of this optional device that
are best suited for use with this printer.
Option
3-5
3-6
Option
4
Computer Interface
This chapter contains explanations on the following topics:
General Information
USB Interface
Network Interface
Computer Interface
4-2
4-2
4-3
4-1
General Information
This chapter explains the connector specifications of USB and network
interfaces.
USB Interface
This printer supports the Hi-Speed USB. USB (Universal Serial Bus)
interface specifications are as follows.
Specifications
Basic specification
Complies with the Universal Serial Bus Specification Revision 2.0.
Connectors
Printer: B-type receptacle (female) with upstream port
Cable: B-type plug (male)
Cable
Use a shielded cable that complies with USB 2.0 (Hi-Speed USB) and
not longer than 5 meters (16 feet).
Transfer Mode
High speed (480 Mbps maximum)
Full-Speed (12 Mbps maximum)
Power Control
Self-power device
Interface Signals
USB Connector Pin Assignment
4-2
Pin
Signal
Description
1
Vbus
Power supply (+5 V)
2
D-
Data transmission
3
D+
Data transmission
4
GND
Signal ground
Shell
—
Shield
Computer Interface
Network Interface
Features
Automatic IP address resolution
This feature is compatible with the DHCP/DHCPv6 protocol and allows
the printer to automatically receive IP addresses from the
DHCP/DHCPv6 server.
Management using Web browsers
HTTP pages are incorporated in to the interface, so that a web browser
can be used to monitor and change a range of settings. The settings can
be password-protected.
Support for a range of protocols
The SMTP, POP3, SSL, SNMP, IPv6 and NetBIOS over TCP/IP
protocols are supported for easier printer management and more robust
security.
Support for IEEE 802.1x
The interface supports EAP-TLS and PEAP authentication.
Supports IPv6
Supports IPv6, which is based on IPv4 with improvements, such as
increased manageable address space, additional security functions and
priority based data transmission.
Supports IPSec
Supports IPSec, the security protocol that authenticates and encrypts in
the network layer (IP layer).
Specifications
Connector
10 Base-T/100 Base-TX/1000 BASE-T
Operating Systems
Windows XP/Vista/7/8/Server2003/2008/2012 R2, MacOS 10.5 or later
Network protocols
• IPv6: HTTP, HTTPS, LPD, FTP, IPP, RawPort, ICMPv6, LLTD, SNTP,
DHCPv6, SMTP, POP3, DNS, SNMPv1/v2c/v3, IPPS, WSD
• IPv4: HTTP, HTTPS, LPD, FTP, IPP, RawPort, ICMP, DHCP, SMTP,
POP3, SNTP, DNS, WINS, NetBIOS over TCP/IP, SNMPv1/v2c/v3,
Bonjour, IPPS, LLTD, WSD
• Etc.: IPX/SPX, NetWare (NDS/Bindery), NetBEUI
Security Protocols
SSL/TLS (HTTPS, IPPS), SNMPv3, EAP-TLS, PEAP, AH, ESP
Computer Interface
4-3
EMI Countermeasures
VCCI Class B, FCC Class B (U.S.), CE (Europe)
IMPORTANT When IPv6 functions are used, the devices used on the
network (routers, PCs, etc) must support IPv6.
4-4
Computer Interface
Glossary
Additional memory
An additional memory (optional) is used for increasing the memory
capacity of this machine. For DIMM that can be used in this machine,
contact your service technician.
AppleTalk
AppleTalk offers file sharing and printer sharing and it also enables you
to utilize application software that is on another computer on the same
AppleTalk network.
Default Gateway
This indicates the device, such as a computer or router, that serves as
the entrance/exit (gateway) for accessing computers outside of the
network that you are on. When no specific gateway is designated for a
destination IP address, data is sent to the host that is designated as the
Default Gateway.
DHCP (Dynamic Host Configuration Protocol)
This is a protocol that automatically resolves the IP address, Subnet
Mask and Gateway address on a TCP/IP network. Use of DHCP
minimizes the load of network administration, especially on network
environments with a large number of client computers where it is not
specifically necessary to assign a separate IP address to each client,
including printers.
dpi (dots per inch)
This indicates the number of dots printed per inch (25.4 mm) as a unit for
expressing resolution.
EcoPrint
This is a printing mode that reduces toner consumption. Pages printed in
the EcoPrint mode are lighter than pages printed in the normal mode.
Emulation
This refers to emulation of other manufacturers' printers. The printer
emulates operation of the following printers: PCL 6, KPDL,
KPDL (AUTO), Line Printer, IBM Proprinter and EPSON LQ-850
Form Feed Timeout
While data is being sent to a printer, some pauses may occur. At this
time, the printer waits for the next data without making a page break.
Form feed timeout is a function to wait only a preset amount of time
before it executes an automatic page break. After the waiting period
begins, once the designated amount of time is exceeded, the printer will
automatically process the currently received data and print it out. If the
machine has received no print data for the last page, the printer ends
processing of that job without outputting paper.
5-1
IP Address (Internet Protocol Address)
The Internet Protocol address is a unique number that represents a
specific computer in a network. The format of an IP Address is four
numbers separated by dots, e.g. 192.168.110.171. Each number should
be a decimal between 0 and 255.
KPDL
KPDL is Kyocera's implementation of the PostScript page description
language Level3.
MP Tray
This tray is used instead of the cassette when printing on envelopes,
postcards, transparency sheets, and labels.
NetBEUI (NetBIOS Extended User Interface)
An enhanced version of the NetBIOS protocol, it enables the utilization
of more advanced functions on small-scale networks than do other
protocols such as TCP/IP, etc.
Outline font
With outline fonts, character outlines are represented with numerical
expressions and fonts can be enlarged or reduced in different ways by
changing the numeric values of those expressions. Printing remains
clear even if you enlarge fonts, since the characters are defined with
outlines represented with numerical expressions. You can specify the
font size in steps of 0.25 points up to 999.75 points.
PostScript
This is a page description language developed by Adobe Systems, Inc. It
enables flexible font functions and highly-functional graphics, allowing
higher quality printing.
PPM (prints per minute)
This indicates the number of printouts made in one minute.
Printer driver
The printer driver makes it possible for you to print data created using
application software. The printer driver for the printer is contained on the
DVD-ROM supplied with the printer. Install the printer driver on the
computer connected to the printer.
Sleep mode
This mode is provided to save power. It is activated when the machine is
not used for a preset period of time. In this mode, power is reduced to
the minimum. The default setting can be changed.
Status page
This lists machine conditions, such as the machine's memory, the total
number of prints and paper source settings. You can print the status
page from the operation panel.
5-2
Subnet Mask
This is a 32-bit numerical value that defines which bits of the IP address
specify the network address and which specify the host address.
TCP/IP (Transmission Control Protocol/Internet Protocol)
TCP/IP is a suite of protocols designed to define the way computers and
other devices communicate with each other over a network.
USB (Universal Serial Bus) 2.0
A USB interface standard for Hi-Speed USB 2.0. The maximum transfer
rate is 480 Mbps. This machine is equipped with USB 2.0 for high-speed
data transfer.
5-3
5-4
Index
Numerics
D
3DES setting
SSL server............................................................. 2-78
Date setting................................................................... 2-56
DES setting
SSL server ............................................................. 2-77
DHCP............................................................................ 2-42
DIMM .............................................................................. 3-2
Duplex path
Setting.................................................................... 2-25
Duplex Printing.............................................................. 2-29
Duplex printing
Binding modes ....................................................... 2-29
Error detection ....................................................... 2-61
A
Adhesive label ................................................................ 1-8
Administrator ID 2-50, 2-56, 2-62, 2-66, 2-68, 2-71, 2-73,
2-81
Change .................................................................. 2-82
Administrator Password 2-50, 2-56, 2-63, 2-67, 2-69, 2-71,
2-73, 2-81
Change .................................................................. 2-83
AES setting
SSL server............................................................. 2-78
Alarm (Buzzer).............................................................. 2-58
Alternative emulation for KPDL..................................... 2-31
AppleTalk ...................................................................... 2-52
Auto cassette change ................................................... 2-27
Auto error clear ............................................................. 2-65
Timer...................................................................... 2-65
Auto panel reset............................................................ 2-63
Timer...................................................................... 2-63
Auto-IP.......................................................................... 2-42
Automatic cassette selection ........................................ 2-28
B
Bonjour ......................................................................... 2-44
C
Canceling a printing job .................................................. 2-6
Carriage return code..................................................... 2-38
Cassette
Basis weight ............................................................ 1-5
Minimum and maximum page sizes ........................ 1-3
Paper feed mode ................................................... 2-28
Paper size...................................................... 1-4, 2-21
Paper source ......................................................... 2-26
Paper type ................................................... 1-11, 2-23
Changing default font size ............................................ 2-33
Character pitch ............................................................. 2-33
Code set
Setting ................................................................... 2-34
Colored paper ................................................................. 1-9
Common device
Selecting or setting ................................................ 2-55
Computer interface ......................................................... 4-1
Conventions in this guide................................................... v
Counter
Printed pages ........................................................ 2-18
E
EcoPrint mode .............................................................. 2-36
Emulation
on the status page ................................................. 2-14
Setting.................................................................... 2-30
Enhanced WSD ............................................................ 2-76
Enhanced WSD (SSL) .................................................. 2-76
Envelope ......................................................................... 1-9
Error detection
Duplex printing....................................................... 2-61
MP tray empty........................................................ 2-62
Paper mismatch..................................................... 2-61
Setting.................................................................... 2-61
Expansion memory module
Option ...................................................................... 3-2
F
Features
Network interface..................................................... 4-3
Font select
Selecting default font ............................................. 2-32
G
Gateway........................................................................ 2-44
I
IB-50 ...................................................................... 3-2, 3-5
IB-51 ...................................................................... 3-2, 3-5
Installing memory module ............................................... 3-3
Interface block............................................................... 2-74
Interface signals
USB interface........................................................... 4-2
IPP (Internet Printing Protocol) ..................................... 2-76
IPP over SSL setting
SSL server ............................................................. 2-78
IPSec (IP Security Protocol) ......................................... 2-79
Index-1
J
Job name ...................................................................... 2-40
K
Keys
Basic operation ........................................................ 2-6
Cancel...................................................................... 2-6
Cursor keys.............................................................. 2-7
GO ........................................................................... 2-6
MENU ...................................................................... 2-6
OK............................................................................ 2-7
KPDL Errors .................................................................. 2-31
L
Label ............................................................................... 1-7
LAN interface ................................................................ 2-80
Linefeed code................................................................ 2-38
Low power timer............................................................ 2-64
M
Memory
on the status page ................................................. 2-14
Memory module handling................................................ 3-3
Menu map ..................................................................... 2-12
Menu selection system.................................................... 2-8
Message display
Indicators ................................................................. 2-5
Message language................................................. 2-55
Status information .................................................... 2-4
Message language........................................................ 2-55
Mode selection menu ...................................................... 2-8
MP tray
Basis weight............................................................. 1-5
Minimum and maximum paper sizes ....................... 1-3
Paper size ..................................................... 1-4, 2-19
Paper source.......................................................... 2-26
Paper type................................................... 1-11, 2-20
N
Netware......................................................................... 2-51
Network
Settings .................................................................. 2-41
TCP/IP (IPv4)......................................................... 2-41
TCP/IP (IPv6)......................................................... 2-45
Network interface ............................................................ 4-3
Network interface kit........................................................ 3-5
Option ...................................................................... 3-2
Network settings
FTP (Server) .......................................................... 2-47
HTTP...................................................................... 2-49
LPD ........................................................................ 2-48
NetBEUI ................................................................. 2-46
POP3 ..................................................................... 2-48
Protocol Detail........................................................ 2-46
RAW Port ............................................................... 2-48
Index-2
Restart Network ....................................................
SMTP ....................................................................
SNMP....................................................................
SNMPv3 ................................................................
Number of copies
USB flash memory ................................................
2-49
2-47
2-47
2-47
2-17
O
Operation Panel
diagram ................................................................... 2-3
Option
Expansion memory module..................................... 3-2
Network interface kit................................................ 3-2
Paper feeder ........................................................... 3-2
Wireless network interface kit ................................. 3-2
Optional network settings ............................................. 2-50
AppleTalk............................................................... 2-52
Communication ..................................................... 2-53
IPSec..................................................................... 2-52
LAN interface ........................................................ 2-52
MACAddressFilter ................................................. 2-53
Netware................................................................. 2-51
Restart network ..................................................... 2-54
TCP/IP................................................................... 2-51
TCP/IP (IPv6) ........................................................ 2-51
Options ........................................................................... 3-2
Override A4/Letter ........................................................ 2-30
P
Page set
Carriage-return...................................................... 2-38
Linefeed ................................................................ 2-38
Number of copies .................................................. 2-37
Print area setting for XPS data.............................. 2-39
Print mode setting for TIFF/JPEG files.................. 2-39
Print orientation ..................................................... 2-37
Wide A4 pitch ........................................................ 2-39
Paper
Minimum and maximum sizes................................. 1-3
Paper feed source ........................................................ 2-26
Paper feeder................................................................... 3-5
Option...................................................................... 3-2
Paper settings .............................................................. 2-19
Paper type
Custom.................................................................. 2-24
Paper weight .................................................................. 1-5
Setting ................................................................... 2-24
PF-100.................................................................... 3-2, 3-5
Postcard ......................................................................... 1-8
Preprinted paper............................................................. 1-9
Print
Fonts list................................................................ 2-15
Menu map ............................................................. 2-11
Network status page ............................................. 2-85
Option network status page .................................. 2-86
RAM disk file list.................................................... 2-15
Status page ................................................. 2-13, 2-85
Test page............................................................... 2-86
Print density
Setting ................................................................... 2-36
Print file
USB flash memory.................................................
Print quality
EcoPrint mode .......................................................
KIR mode...............................................................
Print density...........................................................
Resolution..............................................................
Setting ...................................................................
Print settings .................................................................
Printing a list of files
USB flash memory.................................................
Printing KPDL error report ............................................
Print file.................................................................. 2-16
Print file list ............................................................ 2-17
Remove device ...................................................... 2-17
2-16
2-36
2-35
2-36
2-36
2-35
2-26
2-17
2-31
R
V
Verifying expanded memory ........................................... 3-4
Viewing counter value ................................................... 2-18
W
Wireless network interface kit ......................................... 3-5
Option ...................................................................... 3-2
WSD-PRINT.................................................................. 2-75
RAM Disk...................................................................... 2-60
Recycled paper ............................................................. 1-10
Removing memory module............................................. 3-4
Removing USB flash memory....................................... 2-17
Resetting custom paper type ........................................ 2-25
Restart printer ............................................................... 2-84
S
Security level ................................................................ 2-80
Selecting paper feed source
USB flash memory................................................. 2-17
Selecting regular or dark............................................... 2-32
Service (for maintenance)............................................. 2-85
Sleep level .................................................................... 2-66
Sleep timer.................................................................... 2-64
Special paper .................................................................. 1-7
Specifications
Network interface..................................................... 4-3
USB interface .......................................................... 4-2
SSL (Secure Sockets Layer) Server ............................. 2-77
Status page sample ...................................................... 2-13
Subnet mask................................................................. 2-43
T
Time setting .................................................................. 2-56
Timer setting
Auto error clear...................................................... 2-65
Auto panel reset .................................................... 2-63
Error clear timer..................................................... 2-65
Form feed time out ................................................ 2-66
Low power timer .................................................... 2-64
Panel reset timer ................................................... 2-63
Sleep timer ............................................................ 2-64
Toner alert level ............................................................ 2-71
Transparency .................................................................. 1-7
U
Unit of measurement .................................................... 2-22
Selecting................................................................ 2-22
USB interface.................................................................. 4-2
USB memory ................................................................ 2-16
Copies ................................................................... 2-17
Paper source ......................................................... 2-17
Index-3
Index-4
We recommend the use of our own brand supplies.
We will not be liable for any damage caused by the use of third party supplies in this machine.
TA Triumph-Adler GmbH
Betriebsstätte Norderstedt
Ohechaussee 235
22848 Norderstedt
Germany
Rev.1 2014.7
2PJGEEN401