Razor Scream Machine Owner`s manual

™
NOTE: The eSpark must be traveling up to 3mph before motor will engage. Kick start
up to 3mph while twisting the throttle to engage motor.
Owner’s Manual
Read and understand this entire manual before riding!
DO NOT RETURN TO STORE!
NOTE: Manual illustrations are for demonstration purposes only. Illustrations
may not reflect exact appearance of actual product. Specifications subject to
change without notice.
v.1_07-11_US
Item Number:
13111290
Contents
Safety Warnings.......................................................... 1-2
Before You Begin............................................................ 3
Assembly and Set-Up.................................................. 3-5
Connectors/Hardware Maintenance............................... 5
Repair and Maintenance.............................................. 6-8
Troubleshooting Guide............................................... 9-10
Electric Scooter Parts................................................... 11
Warranty....................................................................... 13
Safety Warnings
WARNING: SPARKS CAN INDUCE FIRE
The recommended rider age is 8 and older. Any rider unable to fit comfortably
on the scooter should not attempt to ride it. A parent’s decision to allow his
or her child to ride this product should be based on the child’s maturity, skill
and ability to follow rules.
To reduce the risk of SERIOUS INJURY or FIRE:
PARENTS and RIDERS: Make sure riders understand that sparks can start a
fire. Keep sparks away from flammable or combustible substances. Use only
under close adult supervision.
Keep this product away from small children and remember that it is
intended for use only by persons who are, at a minimum, completely
comfortable and competent while operating the scooter.
BE RESPONSIBLE: Safety is important. Parents must review the following
warnings and instructions with each rider:
DO NOT EXCEED THE WEIGHT LIMIT OF 120 pounds (54kg). Rider weight
does not necessarily mean a person’s size is appropriate to fit or maintain
control of the scooter.
• For outdoor use only on solid, clean, dry, hardened surfaces. Keep sparks away from substances that can catch fire, such as dry vegetation, paper, chemicals or gasoline. Sparks can induce fire.
Do not touch the brakes, Spark Bar or motor on your scooter when in use or
immediately after riding as these parts can become very hot..
• Do not use in any area prone to wildfires or posted by fire authorities as a Fire Hazard Zone.
ACCEPTABLE RIDING PRACTICES AND CONDITIONS
Always check and obey any local laws or regulations which may
affect the locations where the electric scooter may be used.
Ride defensively. Watch out for potential obstacles that could catch your
wheel or force you to swerve suddenly or lose control. Be careful to avoid
pedestrians, skaters, skateboards, scooters, bikes, children or animals who
may enter your path, and respect the rights and property of others.
• Never use your scooter to try to start a fire. Your eSpark™ scooter emits localized sparks when the Spark Bar on a moving scooter comes in contact with hardened outdoor surfaces like asphalt or concrete. Be responsible.
• Do not ride at night.
• Keep sparks away from eyes, hair, exposed skin and clothing. Sparks can burn.
Do not activate the speed control on the hand grip unless you are on the
scooter and in a safe, outdoor environment suitable for riding. The electric
scooter must be moving at 3 miles per hour before the motor will
engage.
• Spark Bar and cartridge get hot during use. Do not touch after use.
• Do not depress the Spark Bar continuously - only for short periods - while
the scooter is moving under power, as this may overheat components.
Always allow to cool (at least 15 minutes recommended) before replacing a
worn spark cartridge.
Do not attempt or do stunts or tricks on your electric scooter. The scooter is
not made to withstand abuse from misuse such as jumping, curb grinding or
any other type of stunts.
• Observe all other eSpark scooter safety warnings and instructions as provided elsewhere in this manual.
Maintain a hold on the handlebars at all times.
Never allow more than one person at a time to ride the scooter.
Never use near steps or swimming pools.
WARNING: Riding the electric scooter can be a hazardous activity.
Certain conditions may cause the equipment to fail without fault of the
manufacturer. Like other electric products, the scooter can and is intended
to move and it is therefore possible to lose control, fall off and/or get into
dangerous situations that no amount of care, instruction or expertise can
eliminate. If such things occur you can be seriously injured or die, even when
using safety equipment and other precautions. RIDE AT YOUR OWN RISK
AND USE COMMON SENSE.
Keep your fingers and other body parts away from the chain, steering system,
wheels and all other moving components.
Never use headphones or a cell phone when riding.
Never hitch a ride with another vehicle.
Do not ride your scooter in wet or icy weather and never immerse the scooter
in water, as the electrical and drive components could be damaged by water
or create other possibly unsafe conditions.
This manual contains many warnings and cautions concerning the
consequences of failing to maintain, inspect or properly use your electric
scooter. Because any incident can result in serious injury or even death, we
do not repeat the warning of possible serious injury or death each time such
a possibility is mentioned.
The electric scooter is intended for use on flat, dry surfaces such as
pavement or level ground without loose debris such as sand, leaves, rocks or
gravel. Wet, slick, bumpy, uneven or rough surfaces may impair traction and
contribute to possible accidents. Do not ride your scooter in mud, ice, puddles
or water. Avoid excessive speeds that can be associated with downhill rides.
Never risk damaging surfaces such as carpet or flooring by use of an electric
scooter indoors.
APPROPRIATE RIDER USE AND
PARENTAL SUPERVISION
This manual contains important safety information. It is your responsibility
to review this information and make sure that all riders understand all
warnings, cautions, instructions and safety topics and assure that young
riders are able to safely and responsibly use this product. Razor recommends
that you periodically review and reinforce the information in this manual
with younger riders, and that you inspect and maintain your child’s scooter to
insure their safety.
Do not ride at night or when visibility is limited.
Observe all other eSpark safety warnings and instructions as provided
elsewhere in this manual.
1
Safety Warnings
PROPER RIDING ATTIRE
Always wear proper protective equipment such as an approved safety helmet
(with chin strap securely buckled), elbow pads and kneepads. A helmet may
be legally required by local law or regulation in your area. A long-sleeved
shirt, long pants, and gloves are recommended. Always wear athletic shoes
(lace-up shoes with rubber soles), never ride barefooted or in sandals, and
keep shoelaces tied and out of the way of the wheels, motor and drive
system.
WARNING: ALWAYS INSPECT SCOOTER PRIOR TO RIDING. Properly
inspecting and maintaining your scooter can reduce the risk of injury. Always
inspect your scooter before riding and regularly maintain it.
WARNING: CHECK LOCAL LAWS REGARDING SCOOTER USE. Check
local laws and regulations to see where and how you may use your Razor
scooter legally. In many states and local areas scooter riders are required
BY LAW to wear a helmet. Check local laws and regulations regarding laws
governing helmet use and scooter operation in your area, including laws or
regulations designating High Fire Hazard areas.
USING THE CHARGER
The charger supplied with the electric scooter should be regularly examined
for damage to the cord, plug, enclosure and other parts, and in the event of
such damage, the scooter must not be charged until the charger has been
repaired or replaced.
FAILURE TO USE COMMON SENSE AND HEED THE ABOVE
WARNINGS FURTHER INCREASES SUCH RISKS OF SERIOUS
INJURY. USE AT YOUR OWN RISK AND WITH APPROPRIATE
AND SERIOUS ATTENTION TO SAFE OPERATION. USE CAUTION.
Use only with the recommended charger.
Use caution when charging.
The charger is not a toy. Charger should be operated by an adult.
Do not operate charger near flammable materials.
Unplug charger and disconnect from scooter when not in use.
Always disconnect from the charger prior to wiping down and cleaning your
scooter with liquid.
2
Before You Begin
Remove contents from box. Remove the foam separators that protect the components from damage during
shipping. Inspect the contents of the box for scratches in the paint, dents or kinked cables that may have
occurred during shipping. Because the scooter was 95 percent assembled and packed at the factory, there
should not be any problems, even if the box has a few scars or dents.
MAKE SURE POWER SWITCH IS TURNED “OFF” BEFORE CONDUCTING ANY
MAINTENANCE PROCEDURES.
Estimated Assembly and Set-Up Time
Razor recommends assembly by an adult with experience in bicycle mechanics.
Allow up to 20 minutes for assembly, not including initial charge time.
Allow up to 12 hours for initial charge (see page 4 for charging information)
Charger
(Note: Charger design may vary
from one shown)
Charger
Port
Brake Lever
WARNING:
DO NOT USE NONRAZOR PRODUCTS
WITH YOUR RAZOR
ELECTRIC SCOOTER.
The scooter has been built
to certain Razor design
specifications. The original
equipment supplied at the time
of sale was selected on the
basis of its compatibility with
the frame, fork and all other
parts. Certain aftermarket
products may not be compatible
and will void the warranty.
Note: Electric scooter must
be moving at 3mph/5km while
twisting the throttle to engage
motor.
Twist Grip Throttle
Charger
Plug
Handlebar
Stem
Push Button
Spark Bar
Quick Release
On/Off switch
Reset Button
Charger Port
Limiter
Spark Cartridge
Motor
- Battery
- Control Module
Required Tools
5mm Allen wrench
(Included)
8mm, 10mm, 13mm and
16mm open wrenches
(Not Included)
Phillips
Screwdriver
(Not Included)
Bicycle-style tire pump
for Schrader valve tires,
with pressure gauge
(Not included)
Need Help? Visit our web site for replacement parts, product support and a list of authorized service centers
at www.razor.com or call toll free 866-467-2967 Monday - Friday 8AM - 5PM Pacific Time.
3
Assembly and Set-Up
q Attaching the Handlebars
Note: Make sure the cables/
wires are out of the way before
inserting the stem into the fork.
(a)
1 Open the quick release.
2 Depress the push button (a)
located on the front fork and insert the handlebar stem until the
bottom of the handlebar stem
locks securely onto the fork.
3 Adjust the tension of the
quick release to where you can
close the lever all the way to
secure the stem.
q Inflating the Tire
The front tire is inflated when shipped but it invariably may lose some pressure between the point of
manufacturing and your purchase.
WARNING: Failure
to recharge the battery at least
once a month may result in
a battery that will no longer
accept a charge.
1 Using a bicycle style tire
pump equipped for a Schradertype valve, inflate the front tire
to the correct PSI indicated on
the sidewall of the tire.
q Charging the Battery
Your electric scooter may not have a fully charged battery; therefore it is a good idea to charge the battery
prior to use.
•Initial charge time: 12 hours
•Recharge time: up to 12 hours, depending on level
of depletion and even if the light turns green.
•Fully charge battery before storing.
•When the scooter is not in regular use, recharge
the battery at least once a month until normal
use is resumed.
•Run time: Up to 40 minutes of continuous ride time.
Run time may vary depending on riding conditions,
climate and/or proper maintenance.
•Average battery life: 250 charge/discharge cycles
•To ensure long battery life, do not store the battery
in temperatures above 75° or below -10° F.
WARNING:
Rechargeable batteries are
only to be charged under adult
supervision. Always disconnect
your scooter from the charger
before cleaning with liquid.
Note: If your charger does not
look like the one illustrated,
your unit has been supplied
with an alternative charger.
The specifications and charging
procedure would not change.
The charger has a small window
with one LED to indicate the
charge status. Refer to the
illustration on the charger unit
for the actual “charging” and
“charged” status indications for
your model charger.
Charger
Note: Make sure power is
turned OFF when unit is not in
use. If the power switch is left
on for an extended period of
time, the battery may reach a
stage at which it will no longer
hold a charge.
Note: The pressurized air
supplies found at gasoline
stations are designed to inflate
high-volume automobile tires.
If you decide to use such an
air supply to inflate the tire,
first make sure the pressure
gauge is working, then use very
short bursts to inflate to the
correct PSI. If you inadvertently
over-inflate the tire, release the
excess pressure immediately.
2 Turn power OFF before
1 Plug the charger into a wall
charging. Plug the charger into
the charger port to charge unit.
outlet. If the lights on charger
do not light up, check the power
to the outlet. If necessary, try a
different outlet.
4
Chargers have built-in over-charge
protection to prevent battery from
being over-charged.
Charger will get warm during use.
This is normal for some chargers
and is no cause for concern. If
your charger does not get warm
during use, it does not mean that
it is not working properly.
Assembly and Set-Up
q Installing Spark Bar
1 Using two (2) 5mm Allen
wrenches remove the coupling
bolt that is attached to the end
of the metal bar of the Spark
Bar. Slide the Spark Bar onto
the metal bar located on the
opposte side of the chain. Push
down on the Spark Bar and slide
the bar all the way on until the
holes are aligned.
2 Re-insert the coupling bolt
through the metal bar and
tighten until Spark Bar is locked
securely in place.
CONNECTORS/HARDWARE MAINTENANCE
q
Brake
q
q
Frame, Fork and Handlebars
q
q
Tires
Check the brakes for proper function. When you squeeze the lever,
the brake should provide positive braking action. When you apply
the brake with the speed control on, the brake cut-off switch
should stop the motor. Make sure that brakes are not rubbing.
Check for cracks or broken connections. Although broken frames
are rare, it is possible for an aggressive rider to run into a curb
or wall and wreck and bend or break a frame. Get in the habit of
inspecting your scooter on a regular basis.
Safety Gear
Always wear proper protective gear such as an approved safety
helmet. Elbow pads and kneepads are recommended. Always
wear athletic shoes (lace-up shoes with rubber soles), never ride
barefooted or in sandals, and keep shoelaces tied and out of the
way of the wheels, motor and drive system.
Battery
Make sure the power switch is turned off whenever the scooter is
not in use. Never store the product in freezing or below freezing
temperatures! Freezing will permanently damage the battery.
Recharge the battery at least once a month when scooter is not
in use.
Periodically inspect the tires for excess wear and regularly check
the front tire pressure and re-inflate as necessary.
Do not use this product for the first time until you have inflated
the front tire to the correct PSI and charged the battery for at
least 12 hours. Failure to follow these instructions may damage
your product and void your warranty.
5
Repair and Maintenance
Turn power switch “OFF” before conducting any maintenance procedures.
q Adjusting the Brakes
1 To adjust the brake cable
play, thread the brake lever
adjuster in or out 1/4 to 1/2 turn
until the desired brake adjustment is attained. Most
adjustments are complete at
this step. If brake still needs
further adjustment, proceed to
step 2.
2 If brake is too tight or has
too much slack, use a 10mm
open wrench to loosen the
brake cable and adjust accordingly.
3 Inspect the brake pads (A)
for proper alignment against
the wheel or excess wear. To
realign brake pads, loosen the
fixing nut (B) and adjust the pad
to contact the rim. Retighten
and test. Readjust as needed.
Note: Front wheel hardware
sequence
9-5
9-3
9-1
9-4
9-5
9-3
9-1
q Front Wheel Replacement
9-6
9-4
9-2
Right Side (Throttle)
9-5 - (Short) spacer
9-4 - Flat washer
Fork
9-3 - Flat washer
9-2 - Lock washer
9-1 - 17mm locknut
1 Using a 10mm open wrench,
loosen the brake cable bolt.
2 Using two 17mm open
Middle
wrenches, loosen the locknuts
by turning the wrenches counter
clockwise. Remove wheel and
install replacement wheel.
9-6 - Front axle bolt
Left Side (Brake)
9-5 - (Short) spacer
9-4 - Flat washer
Fork
9-3 - Flat washer
9-2 - Lock washer
9-1 - 17mm locknut
Need Help? Visit our web site for replacement parts, product support and a list of authorized service centers
at www.razor.com or call toll free 866-467-2967 Monday - Friday 8AM - 5PM Pacific Time.
6
9-2
Repair and Maintenance
q Chain and Rear Wheel Replacement
Tools required: Phillips screwdriver, 10mm open wrench, two (2) 8mm open wrenches, and two (2) 13mm
open wrenches.
Note: Rear wheel hardware
sequence
18-1
18-2
18-4
18-7
18-8
18-5
18-3
1 With a Phillips screwdriver,
loosen the two screws on the
chain guard and remove the
chain guard.
2 Using two 13mm open
3 To loosen the chain, push the
tensioner down to create some
slack in the chain.
wrenches, loosen the locknuts
by turning the wrenches counter
clockwise.
18-4
18-2
18-1
Left Side (Brake)
18-1 Locknut
18-2 Lock washer
18-3 Flat washer
Frame
18-4 Thick washer
18-6 Spring
18-7 Spring housing
18-8 (Long) spacer
4 Remove wheel and install
replacement wheel.
(Note the sequence of the
hardware)
5 Push the chain tensioner
6 With two 13mm open
down to install the chain on
both sprockets.
wrenches, re-tighten the
locknuts.
Right Side (Throttle)
18-1 Locknut
18-2 Lock washer
18-3 Flat washer
Frame
18-4 Thick washer
18-5 (Short) spacer
7 Re-attach the chain guard.
q When to Replace the Spark Cartridge
Spark cartridge will continue to emit sparks until it is worn to the indicator line.
Indicator line
7
18-3
18-6
Repair and Maintenance
q Replacing the Spark Cartridge
Friction during sparking will eventually wear out the replaceable cartridge and cause the scooter to stop making
sparks. Worn out cartridges must be replaced.
WARNING: Do not
attempt to replace cartridge
immediately after riding as
cartridge will be hot. Handle only
when cool.
A
WARNING: Keep fingers
clear of Spark Bar hinge .
B
1 Using your thumbs, press tabs
(A & B) on both sides of the cartridge to release from the bracket.
Slide cartridge away from you and
remove from bracket.
2 Place a new cartridge in back of the bracket making sure to align the slots on the cartridge with the
two legs of the bracket and slide cartridge forward
until you hear a click and the thumb tabs are locked
in place.
q Using the Spark Bar
When riding, place ball of foot on the Spark Bar and gradually apply pressure. Only use enough pressure to cause
sparking action. Do not engage the Spark Bar for extended or continuous periods of use.
WARNING: Applying too
much pressure on the Spark Bar
may cause loss of control.
NOTE: Sparks and Spark
cartridge life will vary based on
the amount of pressure applied
to the Spark Bar, the length of
time pressure is applied and
the smoothness of the riding
surface.
q Battery Care and Disposal
Do not store the battery in temperatures above 75° F (23.8° C) or below -10° F (-23.3° C).
CONTAINS SEALED LEAD ACID BATTERIES. BATTERIES MUST BE RECYCLED.
Disposal: Your Razor product uses sealed lead-acid batteries which must be recycled or disposed of in an
environmentally safe manner. Do not dispose of a lead-acid battery in a fire. The battery may explode or leak. Do not
dispose of a lead-acid battery in your regular household trash. The incineration, land filling or mixing of sealed leadacid batteries with household trash is prohibited by law in most areas. Return exhausted batteries to a federal or state
approved lead-acid battery recycler or a local seller of automotive batteries. If you live in Florida or Minnesota, it is
prohibited by law to throw away lead-acid batteries in the municipal waste stream.
q Charger
The charger supplied with the electric scooter should be regularly examined for damage to the cord, plug, enclosure
and other parts and in the event of such damage, the product must not be charged until it has been repaired or
replaced.
Use ONLY with the recommended charger.
WARNING: If a battery
leak develops, avoid contact with
the leaking acid and place the
damaged battery in a plastic bag.
Refer to the disposal instructions at
left. If acid comes into contact with
skin or eyes, flush with cool water
for at least 15 minutes and contact
a physician.
q Wheels
Wheels and drive system are subject to normal wear and tear. It is the responsibility of the user to periodically inspect
wheels for excess wear and adjust and replace drive train components as required.
q Replacement Parts
The most frequently requested replacement parts are available for purchase at some Razor retail partners. For the
complete selection of replacement parts visit www.razor.com/shop.
WARNING: Battery
posts, terminals and related
accessories contain lead and lead
compounds. Wash your hands
after handling.
q Repair Centers
For a list of authorized Razor repair centers:
• Check online at www.razor.com.
• Call 866-467-2967 for the center nearest you.
Need Help? Visit our web site for replacement parts, product support and a list of authorized service centers
at www.razor.com or call toll free 866-467-2967 Monday - Friday 8AM - 5PM Pacific Time.
8
Troubleshooting Guide
Problem
Possible Cause
Solution
Scooter does not run
Scooter must be traveling 3mph
before motor will engage.
Kick start to 3mph while twisting the throttle to engage motor.
Battery needs a charge
Charge the battery. A new battery should be charged for at least 12
hours before using the scooter for the first time and up to 12 hours
after each subsequent use.
Check all connectors. Make sure the charger connector is tightly
plugged into the charging port and that the charger is plugged into
the wall.
Scooter suddenly
stopped working while
in use
Charger is not working
Make sure power flow to the wall outlet is on.
Tripped circuit breaker
Check all wires and connectors to make sure they are tight.
The circuit breaker (next to on/off switch) will automatically shut off
the power if the motor is overloaded.
An excessive overload, such as too heavy a rider or too steep a hill,
could cause the motor to overheat. If the scooter suddenly stops
running, wait a few seconds and then push the breaker to reset the
circuit. Correct the conditions that caused the breaker to trip to avoid
repeatedly tripping the breaker.
Short run time (less
than 15 minutes per
charge)
Undercharged battery
Charge the battery. A new battery should be charged for at least 12
hours before using the scooter for the first time and up to 12 hours
after each subsequent use.
Check all wires and connectors. Make sure the battery connector is
tightly plugged into the charger connector and that the charger is
plugged into the wall.
Make sure power flow to the wall outlet is on.
Scooter runs sluggishly
Battery is old and will not accept
full charge
Even with proper care, a rechargeable battery does not last forever.
Average battery life is 1 to 2 years depending on scooter use and
conditions. Replace only with a Razor replacement battery.
Brakes are not adjusted
properly
Refer to adjusting the brakes instructions on page 6.
Riding conditions are too stressful
Use only on solid, flat, clean and dry surfaces such as pavement or
level ground.
Tire is not properly inflated
The tire is inflated when shipped, but it invariably will lose some
pressure between the point of manufacturing and your purchase.
Refer to instructions on page 4 of this manual to properly inflate tire.
Scooter is overloaded
Make sure you do not overload the scooter by allowing more than
one rider at a time, exceeding the electric scooters 120 pounds (54kg)
maximum weight limit, going up a hill or towing objects behind the
scooter. If the scooter is overloaded, the circuit breaker may trip and
shut off power to the motor. Correct the riding conditions that caused
the overload, wait a few seconds, and then push the breaker to reset
the circuit. Avoid repeatedly tripping the circuit breaker.
Brake dragging
Turn off scooter and use your fingers to twist the adjuster in either
direction until front wheel is centered between pads.
Brakes are not adjusted properly
Refer to adjusting the brakes instructions on page 6.
9
Troubleshooting Guide
Problem
Possible Cause
Solution
Sometimes the scooter
doesn’t run, but other
times it does
Loose wires or connectors
Check all wires around the motor and all connectors to make sure
they are tight.
Motor or electrical switch
damage
Contact your local Razor authorized service center for diagnosis and
repair.
Scooter makes loud
noises or grinding
sounds
Chain is too dry
Apply a lubricant such as 3 in 1 or Tri-Flow to the chain.
TM
For more helpful troubleshooting guides, visit us at www.razor.com.
10
TM
parts
Keep your scooter running for years with genuine Razor parts. Visit our website for more information on spare part availability.
(Specifications subject to change without notice.)
01
Handlebar grip (right/left)
13
Charger Port
02
Single speed twist grip throttle
14
Reset Button
02-1 Sleeve
15
Kickstand
03
Handlebar stem
16
Motor (24V / 100W)
04
Brake lever assembly
17
Battery (2 - 12V/4.5Ah)
05
Quick release
18
Rear wheel complete
06
Headset (upper/lower)
(See pg. 7 for hardware sequence)
07
Front Fork with limiter
19
Chain tensioner
08
Front caliper brake with brake pads
20
Chain
09
Front wheel complete
21
Chain guard
(See pg. 6 for hardware sequence)
22
Battery bracket
10
Battery Tray
23
Deck plate with grip tape
11
Control Module
24
Spark Bar
12
On/Off switch
25
Spark cartridge
Need Help? Visit our web site for replacement parts, product support and a list of authorized service centers
at www.razor.com or call toll free 866-467-2967 Monday - Friday 8AM - 5PM Pacific Time.
11
SB 1918 (CALIFORNIA) DECLARATION
YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS
INVOLVING THE USE OF THIS SCOOTER/ELECTRIC RIDE-ON PRODUCT. TO
DETERMINE IF COVERAGE IS PROVIDED, YOU SHOULD CONTACT YOUR
INSURANCE COMPANY OR AGENT.
12
Warranty
Razor Limited Warranty
Razor does not offer an extended warranty. If you have purchased an
extended warranty, it must be honored by the store at which it was
purchased.
The manufacturer warranties this product to be free of manufacturing defects
for a period of 90 days from date of purchase. This Limited Warranty does
not cover normal wear and tear, tires, tubes or cables, or any damage, failure
or loss caused by improper assembly, maintenance, or storage or use of the
Razor eSpark™.
For your records, save your original sales receipt with this manual and write
the serial number below.
__________________________________________
This Limited Warranty will be void if the product is ever
• used in a manner other than for recreation;
• modified in any way;
• rented.
Item Number:
13111290
The manufacturer is not liable for incidental or consequential loss or damage
due directly or indirectly to the use of this product.
Need Help? Visit our web site for replacement parts, product support and a list of authorized service centers at
www.razor.com or call toll free 866-467-2967 Monday - Friday 8AM - 5PM Pacific Time.
U.S. Design Patent D497,397 S
Printed in China for:
Razor USA LLC
PO Box 3610
Cerritos, CA 90703
Copyright © 2003-2011 Razor USA LLC. All rights reserved. RAZOR and the Razor Logo Design are
among the registered trademarks of Razor USA LLC in the United States and/or select foreign countries. eSpark is trademark of Razor USA.
13
07/2011