Westinghouse WB65F1D1 User`s manual

USER’S MANUAL
MANUEL DE L’UTILISATEUR
MANUAL DEL USUARIO
WB55F1D1
WB65F1D1
WB70F1D1
Interactive White Board
Owner’s Operating Manual
Before operating the unit, please read this manual thoroughly,
and retain it for future reference.
Contents
Safety Warning
Installation
Setting and Connections
Menu Operation
Troubleshooting
Care and Maintenance
Display Mode
Safety Warning
Before operating the unit, please read this manual thoroughly,
and retain it for future reference.
Placement
Do not place the unit on an unstable cart, stand, tripod, bracket, table, or shelf. Do not expose the unit to direct sunlight and other sources of heat.
Do not place the unit near appliances that create magnetic fields.
Do not handle liquids near or on the unit.
Never spill liquid of any kind into the unit
Do not put heavy objects on top of the unit.
Power Supply
Check that the unit’s operating voltage is identical with your local power supply.
Please unplug power supply and aerial plug during a thunder (lightening) storm.
Please unplug power supply, when there is nobody at home or not using over a long period
of time.
Please protect power cord from any physical or mechanical damage.
Please use power cord provided, don't modify or lengthen it.
Please check and ensure AC source is grounded.
For 55/65/70/84 inch Display equipment: Fuse rating in inlet is 6.3A, 250 VAC. LCD Screen
Never use any other tough or sharp object to replace with the original touch-write pen.
Unplug the power supply before cleaning.
Clean the screen with a soft dustless dry cloth.
Never use water or detergent to clean the unit.
For deep clean, contact an authorized service center.
Please don't display the high brightness image on the screen for a long time.
Observation Distance
The best distance between audience and screen is 5-7 times that of screen size diagonally.
The best watching angle between audience and screen is within 176 degrees.
Temperature
Do not place the unit near a radiator or heater.
If your unit is suddenly moved from a cold to a warm place, unplug the power cord for
at least two hours allowing the moisture that may have formed inside the unit to dry.
Normal operating temperature is 0~40℃, storage temperature is -20~60℃
Humidity
Do not expose machine to rain, damp area or place near water.
Ensure the indoor operating humidity is 10~90%, storage humidity is 10~95%.
Ventilation
Keep all ventilation openings clear.
Ensure that the unit has enough space for ventilation around: left, right and back >10cm,
top> 20cm.
Earphone
Prolonged use of earphone with louder sound can affects your hearing.
Before using earphone, please turn down the sound volume.
Standby
Standby mode will not turn off the unit.
Double click standby key in order to activate standby mode.
Battery
Properly maintain the batteries and recycle the used batteries.
CAUTION
This is a Class A product, there may be a possibility to cause radio interference.
Installations
Open your package
1) Checking parts:
Warranty Card, Quick Use, Remote Control, Power Cord, VGA/USB/Audio/AV/YPBPR cables,
Batteries, hand-write-touch-pen and CD
2).The mobile bracket (matched) takes material object as the standard
3).The wall bracket (matched) takes material object as the standard
2) Installation
1).Please read “Mobile Bracket Installing Instruction” while installing.
2).Please read “Wall Bracket Installing Instruction” while installing.
Control Panel (located at the Front panel)
①power Display power on/off ②VOL+/‐ Sound Volume adjustment ③P+/‐ Menu Position up/down ④MENU To display MENU image ⑤Source To switch INPUT source Power on/off 1 (one): ON, 0 (zero): OFF ⑥
Input/Output Terminals
YPbPr signal input (DVD, set ‐top ‐box with YPbPr output etc) 1
○
YPbPr 2
○
AUDIO OUT
3
○
AV-1 IN Composite video and Audio signals (R-L)
4
○
AV-2 IN
Composite Video and Audio signals (R-L) by RCA terminals
Earphone or to another external Audio equipment Digital sound signal interface 5
○
SPDIF-audio 6
○
RS232 Serial interface, Used for transfer data/commands
7
○
USB
USB terminal (Touch panel) the same to #16
8
○
POWER 9
○
POWER PC
Turn ON/OFF the internal PC power (if installed)
10
○
RESET PC
Suspend all programs currently running, the system re‐start
11
○
VGA-1 IN
12
○
VGA-2 IN 13
○
VGA OUT
14
○
Audio-1 IN
15
Audio-2 IN
Audio‐2 input (related to VGA‐2 input) 16
Mic IN
Microphone input 17
USB
USB terminal (touch panel) the same to #7 18
USB
USB terminal for other peripheral such as mouse, hard‐disk 19
HDMI-1 IN
High Definition Multimedia Interface‐1 20
HDMI-2 IN
High Definition Multimedia Interface‐2 Power Inlet Analog RGB-1 input
Analog RGB-2 Input VGA output Audio‐1 input (related to VGA‐1 input) 5 Remote control
Remote Control Buttons` Function Description
2 MUTE Power supply switch, Turn on and off the AC source
Mute ON/OFF.
3 P.MODE Picture mode selection 4 S.MODE Sound Mode selection. 1 POWER Play/Pause 5 6 FEC Close the LCD screen only listen to the current sound Stop the current playback 7 8 RETURN Return to previous channel Previous/reverse 9 10 11 12 Fast forward Next track Fast reverse 13 INFO Shows the current signal source information 14 ASPECT The image display is switched between 16:9 and 4:3 picture modes 15 ▲ Direction button ,press to move up 16 ◄ Direction button, press to move left 17 ► Direction button, press to move right 18 ▼ Direction button, press to move down 19 ENTER Enter button, press to select status 20 MENU Display MENU screen 21 EXIT ESC/EXIT, Press to exit current status; DVD menu button.
22 VGA Analog RGB, VGA input 23 HDMI HDMI input selection, also be switched between HDMI1 and HDMI2 24 VIDEO Video input selection, also be switched between video 1 and video 2 25 USB USB terminal 26 SOURCE Source input signal selection 27 VOL+、VOL- Sound Volume, increase and decrease 28 ZOOM Increase or decrease the picture zoom size 29 SLEEP Set the sleep time NOTE: Functions related to PC will only work if internal PC is installed.
Functions related to DVD will only work if DVD module is installed. 2 Remote Control Instruction
Insert the Batteries
1 Remove the cover on the rear of the remote control
2 Insert two “AAA” batteries
3 Place the cover
Remote control area
The range of remote control receiver as shown CAUTION
RISK OF DAMAGE IF BATTERY IS REPLACED WITH AN INCORRECT TYPE
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS
Connecting and Setting
For the safety of you and your unit, please do not connect any power source before the
external device is installed
1 External Computer and Touch Connecting
(1) Connect a VGA cable (15pin) between the PC-VGA Input and Output of external PC.
Connect an audio cable between the PC and display. (2) Connect a USB cable between the external PC and USB terminal
(3) Plug-in the POWER cord and switch the display on.
(4) Start the external computer (Setup the touch driver).
(5) Press 1 (one)
to turn the power on.
(6) Press INPUT and change source to PC.
2 A/V Connection
(1) Connect an AV cable between display and external device through the AV out().
Yellow is Video, Red is Audio-R, White is Audio-L .
(2) Plug-in the POWER cord and turn ON the display.
(3) Press 1 (one)
to turn the power on located on the front of the display.
(4) Press INPUT to change source to AV.
2).MIC IN
(1).Connect
microphone to the MIC IN jack.
(2).Plug-in
the POWER cord and switch it on from the rear panel.
(3).Press
1 (one)
to turn the power on.
3).
Y-Pb-Pr
(1). Connect the Y-Pb-Pr cable between the display and an external device.
(2). Plug-in the POWER cord and switch it on from the rear panel.
(3). Press 1 (one)
to turn the power on. (4). Press INPUT to change source to YPbPr.
4). HDMI1/ HDMI2
(1) Connect a HDMI cable from the display to an external device.
(2).Plug-in the POWER cord and switch it on from the rear panel.
(3) Press 1 (one)
to turn the power on. (4)Press INPUT to change source to HDMI.
3 Coaxial Connecting
(1) Connect a Coaxial cable from display to an external device.
(2) Plug-in the POWER cord and switch it on from the rear panel.
(3) Press 1 (one)
to turn the power on
4 Video-OUT
1) VGA -OUT
(1) Connect a VGA cable from the display to an external device, Connect a Earphone cable
from the display’s audio-out to an external device.
(2) Plug-in the POWER cord and switch it on from the rear panel.
(3) Press 1 (one)
to turn power ON.
(4) Press INPUT to change source input to PC.
(5) Setup the VGA-OUT or Multi-Screen in the internal computer.
Note: VGA-OUT can only output the image from an internal computer
Connections to Internal PC
1 Network cable
2 Microphone Cable
3
USB Device
RS232 connection
After connecting the central control system and unit, you can use some
of the function, such as power on/off or adjust the volume etc.
Internal PC basic operations:
1. Wait about 30 seconds after installing PC to back of the display, press
POWER to turn on the TV and PC together;
2. While booting, press the POWER button, wait for 2 to 3 seconds and then
press the power button again to turn off the TV and PC together;
3. Turn on the PC source, select "WINDOWS" on the lower left corner of
the desktop or press the "WINDOWS" button on the remote control, and
then select the "off", then, turn off the PC but keep the TV on.
4. Turn on TV, the state of the PC is off, it is possible to turn on the
PC by pressing the INPUT button to select PC.
Internal PC unit (option) location
With the model which included the PC unit inside, the location of PC dock located at
behind of the set.
OSD Operation 1. Press menu to display the main menu. 2. Use " / " key to navigate through the menu. Source Menu Select "Source Menu ", use "▲
/▼
" to navigate of each feature press "OK" to make the selection. Picture 1. Press "Menu" key access OSD menu, use " / " to select "Picture" menu. 2. Use "▲
/▼
" to select "Picture Mode", access by "Enter" key, use " / " to select the picture mode. 3. Use "▲
/▼
" to select "Color Temperature", access by "Enter" key, use " / " to select. /▼
" to select "Aspect Ratio 16:9", access by "Enter" key, use " / " to select. 4. Use "▲
/▼
" to select "Noise Reduction", access by "Enter" key , use " / " to select. 5. Use "▲
6. Use "▲
/▼
" to select "PC SETUP", access by "Enter" key ,use " / " to select. Press the "Menu" key to return. Sound 1. Press "Menu" key to access OSD menu, use " / " to select "Sound" menu. 2.Use "▲
/▼
" to select "Sound Mode", access by "Enter" key, use " / " to choose the selection. /▼
" to select "Balance", access by "Enter" key, use " / " to choose the selection. 3.Use "▲
/▼
" to select "Auto Volume", access by "Enter" key ,use " / " to choose the selection. 4.Use "▲
▲
▼
5.Use " / " to select "Surround Sound", access by "Enter" key ,use " / " to choose the selection. /▼
" to select "SPDIF MODE", access by "Enter" key ,use " / " to choose the selection. 6.Use "▲
/▼
" to select "EQ", access by "Enter" key ,use "▲
/▼
/ / " to choose the selection. Press the 7.Use "▲
"Menu" key to return. Time 1.Press "Menu" key to access OSD menu, use " / " to select "Time" menu. /▼
" to select "Time", access by "Enter" key ,use "▲
/▼
/ / " to set the time. 2. Use "▲
3. Use "▲
/▼
" to select "Clock", access by "Enter" key ,use "▲
/▼
/ / " to set the clock time. 4. Use "▲
/▼
" to select "Off Time", access by "Enter" key ,use "▲
/▼
/ / " to choose the selection. /▼
" to select "On Time", access by "Enter" key ,use "▲
/▼
/ / " to choose 5. Use "▲
the selection. 6. Use "▲
/▼
" to select "Sleep Timer", press "Enter" key to select on/off . Press the "Menu" key to return. Option 1.Press "Menu" key to access OSD menu, use " / " to select "Option" menu. 2. Use "▲
/▼
" to select "OSD Language ", access by "Enter" key, use " / " to choose the selection. 3.Use "▲
/▼
" to select "Restore Factory Default", access by "Enter" key, use " / " to choose necessary operation selection. 4. Use "▲
/▼
" to select "Transparency", access by "Enter" key, use " / " to choose the selection. /▼
" to select "OSD Duration", access by "Enter" key, use " / " to choose the 5. Use "▲
selection. Press the "Menu" key to return. USB When USB module inserted, the picture as like as right appears indicating that the module is accepted. Picture : ( play sounds too) /▼
/ / " choose the selections and "enter", Use " / " key select "PHOTO" and "Enter", press"▲
press " " key to play . Press "EXIT" key to return the menu. " " key to play or pause. Next/previous picture : Stop playing and return to the menu. /▼
/ / " to choose the selection, enter by "enter" key. Remark: press "▲
MUSIC Use " / " key select "MUSIC" and "Enter", press "▲
/▼
/ / " to choose the selection, enter by "enter" key. Press " " key to play. Press "EXIT" key to return to the menu. Use " " key to play or pause. Next/previous music REW/FF key : Stop playing and return to the menu. Remark: press "▲
/▼
/ / " to choose the selection, enter by "enter" key. MOVIE Use " / " key to select "MOVIE" and "Enter", press "▲
/▼
/ / " to choose the selection, enter by "enter" key. Press " " key to play. Press "EXIT" key to return the menu. " " key to play or pause. Next/previous movie REW/FF key : Stop playing and return to the menu. Remark: Press "▲
/▼
/ / " to choose your selection, enter by "enter" key. TEXT Use "" key o select "TEXT" and "Enter", press "▲
/▼
/ / " to choose the selection, enter by "enter" key. Press " " key to play. Press "EXIT" key to return the menu. " " key to play or pause. Next/previous movie REW/FF key : Stop playing and return to the menu. Remark: press "▲
/▼
/ / " to choose the selection, enter by "enter" key. Trouble shooting
Remote control:
no function
1 .Check whether there is object between remote control and TV
receiver.
2. Check whether the batteries polarity in remote control is
correct.
3. Check whether the batteries are exhausted.
The unit shuts down
1. Check sleep function if operated.
automatically
2. Check whether there is a sudden power failure.
3. Check for the signal to system and control.
PC mode
No signal
1. Check display setting.
2. Check the resolution.
3. Adjust the Hs & Vs (synchronization) in the menu.
Background streaking
1 .Choose auto-adjust.
2. Adjust clock and phase.
False color
1. Check the VGA.
2. Adjust color, tint, brightness and contrast.
Non supported format
1. Choose auto adjust.
2. Adjust clock and phase.
Touch Function
No Touch
1. Check driver is installed correctly.
Software installed
2. Re-install the driver software. No Touch
1. Check setup and align it.
Function
2. Reinstall driver software.
3. Check whether the touch pen is working properly.
Video not working properly
No picture/No sound
1. Check POWER status.
2. Check the signal cable.
3. Check the internal PC.
Pixelization
1. Check the signal cable.
2. Check for other electronics signal interferences.
Poor picture
1 .Adjust chroma, brightness and contrast in the menu.
2. Check the signal cable.
Audio not working properly
No sound
1. Check the mute function if operated.
2. Adjust sound volume.
3. Check the audio cable.
One speaker
1. Adjust sound balance in the menu.
2. Check the setting in sound control panel of computer.
3. Check the audio cable.
VGA-OUT silence
1. Check for proper earphone connection.
Care and Maintenance
With proper care, your unit will provide you many years of service. Please follow
these guidelines to ensure the maximum performance from your unit.
Cleaning
Unplug the unit from the wall outlet before cleaning or polishing it.
Do not use liquid or aerosol cleaners.
Use a cloth lightly dampened with water for cleaning the exterior of the unit.
Repeat occasionally if possible, Do not use or place liquids near or on the unit.
Don't use machine for a long time as like as 24H-7D operation.
Don't use system for long periods of time, please unplug unit when not in use,
To prevent system failures and power supply surges use power surge protector.
Display mode
1. Y-Pb-Pr (Y-Cb-Cr) Mode
2. VGA Mode
www.westinghousedigital.com
S/N:
Westinghouse Digital International
Orange, CA
SE-UM-0102-1301