MICROWAVE OVEN
M959 (WHITE) / M959C (RED)
M959GR (GREEN)
SERVICE
Manual
MICROWAVE OVEN
CONTENTS
1. Precaution
2. Specifications
3. Operating Instructions
4. Disassembly and Reassembly
1.
2.
3.
1.
2.
3.
Auto
Auto
1.
Auto
2.
3.
5. Alignment and Adjustments
6. Troubleshooting
1 min +
7. Exploded Views and Parts List
8. PCB Diagrams
9. Schematic Diagrams
1. Precaution
Follow these special safety precautions. Although the microwave oven is completely safe during ordinary
use, repair work can be extremely hazardous due to possible exposure to microwave radiation, as well as
potentially lethal high voltages and currents.
1-1 Safety precautions (
)
1. All repairs should be done in accordance
with the procedures described in this
manual. This product complies with
Federal Performance Standard 21 CFR
Subchapter J (DHHS).
2. Microwave emission check should be
performed to prior to servicing if the oven is
operative.
3. If the oven operates with the door open :
Instruct the user not to operate the oven and
contact the manufacturer and the center for
devices and radiological health immediatly.
4. Notify the Central Service Center if the
microwave leakage exceeds 5 mW/cm2
5. Check all grounds.
6. Do not power the MWO from a "2-prong"
AC cord. Be sure that all of the built-in
protective devices are replaced. Restore any
missing protective shields.
7. When reinstalling the chassis and its
assemblies, be sure to restore all protective
devices, including: nonmetallic control
knobs and compartment covers.
8. Make sure that there are no cabinet openings
through which people--particularly
children--might insert objects and contact
dangerous voltages. Examples: Lamp hole,
ventilation slots.
9. Inform the manufacturer of any oven found
to have emmission in excess of 5 mW/cm2,
Make repairs to bring the unit into
compliance at no cost to owner and try to
determine cause.
Instruct owner not to use oven until it has
been brought into compliance.
CENTRAL SERVICE CENTER
10. Service technicians should remove their
watches while repairing an MWO.
Samsung Electronics
11. To avoid any possible radiation hazard,
replace parts in accordance with the wiring
diagram. Also, use only the exact
replacements for the following parts:
Primary and secondary interlock switches,
interlock monitor switch.
12. If the fuse is blown by the Interlock Monitor
Switch: Replace all of the following at the
same time: Primary and secondary switches,
as well as the Interlock Monitor Switch. The
correct adjustment of these switches is
described elsewhere in this manual. Make
sure that the fuse has the correct rating for
the particular model being repaired.
13. Design Alteration Warning:
Use exact replacement parts only, i.e.,
only those that are specified in the
drawings and parts lists of this manual.
This is especially important for the
Interlock switches, described above.
Never alter or add to the mechanical or
electrical design of the MWO. Any design
changes or additions will void the
manufacturer's warranty.10.Always unplug
the unit's AC power cord from the AC
power source before attempting to
remove or reinstall any component or
assembly.
14. Never defeat any of the B+ voltage
interlocks. Do not apply AC power to the
unit (or any of its assemblies) unless all
solid-state heat sinks are correctly installed.
15. Some semiconductor ("solid state") devices
are easily damaged by static electricity. Such
components are called Electrostatically
Sensitive Devices (ESDs). Examples include
integrated circuits and field-effect
transistors.
Immediately before handling any
semiconductor components or assemblies,
drain the electrostatic charge from your
body by touching a known earth ground.
16. Always connect a test instrument's ground
lead to the instrument chassis ground before
connecting the positive lead; always remove
the instrument's ground lead last.
1-1
Pretaution
1-2 Special Servicing Precautions (Continued)
17. When checking the continuity of the witches
or transformer, always make sure that the
power is OFF, and one of the lead wires is
disconnected.
18. Components that are critical for safety are
indicated in the circuit diagram by
shading,
or
.
19. Use replacement components that have the
same ratings, especially for flame resistance
and dielectric strength specifications. A
replacement part that does not have the
same safety characteristics as the original
might create shock, fire or other hazards.
1-3 Special High Voltage Precautions
1. High Voltage Warning
Do not attempt to measureany of the high
voltages--this includes the filament voltage
of the magnetron. High voltage is present
during any cook cycle.
Before touching any components or wiring,
always unplug the oven and discharge the
high voltage capacitor (See Figure 1-1)
2. The high-voltage capacitor remains charged
about 30 seconds after disconnection. Short
the negative terminal of the high-voltage
capacitor to to the oven chassis. (Use a
screwdriver.)
3. High voltage is maintained within specified
limits by close-tolerance, safety-related
components and adjustments. If the high
voltage exceeds the specified limits, check
each of the special components.
Fig. 1-1. Discharging the High Voltage Capacitor
1-2
Samsung Electronics
2. Specifications
2-1 Table of Specifications
TIMER
99 MINUTES 90 SECONDS
POWER SOURCE
230V 50Hz, AC
POWER CONSUMPTION
MICROWAVE : 1,550W
OUTPUT POWER
FROM 100 TO 1000W (10 LEVEL POWER)
(IEC-705 TEST PROCEDURE)
OPERATING FREQUENCY
2,450MHz
MAGNETRON
OM75PH(31)
COOLING METHOD
COOLING FAN MOTOR
OUTSIDE DIMENSIONS
517(W) x 297(H) x 395(D)
POWER LEVEL
ON TIME
OFF TIME
90W
4 sec
26 sec
20%
180W
7 sec
23 sec
30%
270W
10 sec
20 sec
40%
360W
13 sec
17 sec
50%
450W
16 sec
14 sec
60%
540W
19 sec
11 sec
70%
630W
22 sec
8 sec
80%
720W
25 sec
5 sec
90%
810W
28 sec
2 sec
100%
900W
30 sec
0 sec
%
M959
10%
2-2 Comparison Chart
MODEL
FEATURE
Samsung Electronics
M959/ M959C / M959GR
AUTO REHEAT
O
AUTO COOK
O
POWER LEVEL
O
TIME SETTING AND WEIGHT
O
AUTO DEFROST
O
DEODORIZATION
O
2-1
3. Operating Instructions
3-1 Control Panel
1.
2.
3.
1.
2.
3.
Auto
Auto Reheat Programs
Auto
Auto Cook Programs
Power Level Button
1.
2.
3.
Auto Defrost Programs
Auto
10s./
Time Setting
and Weight Selection
1min /g
10min/Kg
Cancel Button
1 min +
Deodorization Button
M959
Start Button
3-2 Features & External Views
Door
Safety Interlock Holes
Light
Ventilation Holes
1.
2.
3.
1.
2.
3.
Auto
Auto
Display
Control Panel
1.
2.
3.
Auto
10s./
1min /g
10min/Kg
1 min +
M959
Glass Plate
Roller Ring
Door Latches
Coupler
2.
3.
2.
3.
Auto
Auto
297mm
1.
1.
1.
2.
3.
Auto
10s./
1min/g
10min/kg
1 min +
517mm
Samsung Electronics
395mm
3-1
4. Disassembly and Reassembly
4-1 Replacement of Magnetron, Motor Assembly and Lamp
Remove the magnetron including the shield case,
permanent magnet, choke coils and capacitors (all
of which are contained in one assembly).
Cover Air
Thermo S/W
Lamp
1. Disconnect all lead wires from the magnetron
and lamp.
2. Remove a screw securing the magnetron
supporter.
3. Remove the magnetron supporter.
4. Remove the air cover.
5. Remove screws securing the magnetron to the
wave guide.
6. Take out the magnetron very carefully.
7. Remove screws from the back panel.
8. Take out the fan motor.
9. Remove the oven lamp by rotating to pull out
from hole of air cover.
NOTE1: When removing the magnetron, make
sure that its antenna does not hit any
adjacent parts, or it may be damaged.
NOTE2: When replacing the magnetron, be sure
to remount the magnetron gasket in
the correct position and make sure the
gasket is in good condition.
Fan Motor
Magnetron
Screw
H. V. Trans
H. V. Capacitor
4-1 Replacement of High Voltage Transformer
1. Discharge the high voltage capacitor.
2. Disconnect all the leads.
3. Remove the mounting bolts.
4. Reconnect the leads correctly and firmly.
PRECAUTION
Servicemen should remov their watches whenever
working close to or replacing the magnetron.
PRECAUTION
There exists HIGH VOLTAGE ELECTRICITY with high
current capabilities in the circuits of the HIGH
VOLTAGE TRANSFORMER secondary and filament
terminals. It is extremely dangerous to work on or
near these circuits with the oven energized.
DO NOT measure the voltage in the high voltage
circuit including filament voltage of magnetron.
Samsung Electronics
Screws
H. V. Trans
4-1
Disassembly and Reassembly
4-3 Replacement of Door Assembly
4-3-1 Removal of Door Assembly
Remove hex bolts securing the upper hinge and
lower hinge. Then remove the door assembly.
Upper Hinge
Screws
Lower Hinge
Screws
4-3-2 Removal of Door "C"
Insert flat screwdriver into the gap between Door
"E" and Door "C" to remove Door "C". Be careful
when handling Door "C" because it is fragile.
4-3-3 Removal of Door "E"
Following the procedure as shown in the figure,
insert and bend a thin metal plate between Door
"E" and Door "A" until you hear the 'tick' sound.
1. Insertion depth of the thin metal plate should be
0.5mm or less.
4-3-4 Removal of Key Door & Spring
Remove pin hinge from Door "E"
Detach spring from Door "E" and key door.
Door "E"
Key Door
4-2
Spring
Samsung Electronics
Disassembly and Reassembly
4-3-5 Reassembly Test
After replacement of the defective component parts of the door, reassemble it and follow the instructions below for proper
installation and adjustment so as to prevent an excessive microwave leakage.
1. When mounting the door to the oven, be sure to adjust the door parallel to the bottom line of the oven
face plate by moving the upper hinge and lower hinge in the direction necessary for proper alignment.
2. Adjust so that the door has no play between the inner door surface and oven front surface. If the door
assembly is not mounted properly, microwave energy may leak from the space between the door and
oven.
3. Do the microwave leakage test.
4-4 Replacement of Fuse
1. Disconnect the oven from the power source.
2. Remove the 10A fuse in the fuse holder.
3. When replacing the 10A fuse, be sure to use an
exact replacement part. If new 10A fuse blows
out again after replacement, check the primary
interlock switch, door sensing switch and
interlock monitor switch.
4. When the above three switches operate properly,
check if any other part such as the control circuit
board, blower motor or high voltage
transformer is defective.
4-5 Replacement of Drive Motor
1. Take out the glass tray, guide roller and coupler
from cavity.
2. Turn the oven upside down to replace the drive motor.
Screw
Drive Motor
3. Remove a screw securing the drive motor cover.
4. Disconnect all the lead wires from the drive motor.
5. Remove screws securing the drive motor to the
cavity.
6. Remove the drive motor.
7. When replacing the drive motor, be sure to
remount it in the correct position.
8. Connect all the leads to the drive motor.
Drive Motor Cover
Base Plate
9. Screw the deive motor cover to the base plate
with a screw driver.
10. Remount the coupler in the correct position.
Samsung Electronics
4-3
Disassembly and Reassembly
4-6 Replacement of Control Circuit Board
4-6-1 Removal of Ass'y Control Box
1. Be sure to ground any static electric charge in
your body and never touch the touch control
circuitry.
2. Disconnect the connectors from the control
circuit board.
SCREW
3. Remove screws securing the control box
assembly.
4. Remove the screw securing the ground tail of
the keyboard.
CONTROL BOX
4-6-2 Remonal of Ass'y P.C.B
1. Pull the lever end of the plastic fastener and
remove the Flexible Printed Circuit(FPC) of
membrane panel.
2. Remove screws securing the control circuit
board.
3. Lift up the control circuit board from the Ass'y
control box.
4. When reconnecting the FPC connector, make
sure that the holes on the connector are properly
engaged with the hooks on the Plastic Fastener.
4-4
screw
FPC
Connector
screw
Samsung Electronics
5. Alignment and Adjustments
PRECAUTION
1. High voltage is present at the high voltage terminals during any cook cycle.
2. It is neither necessary nor advisable to attempt measurement of the high voltage.
3. Before touching any oven components or wiring, always unplug the oven from its power source and discharge the high
voltage capacitor.
5-1 High Voltage Transformer
1. Remove connectors from the transformer terminals
and check continuity.
2. Normal resistance readings are as follows:
MODEL
Filament Terminals
M959/ M959C / M959GR
Secondary
Filament
Primary
Approx. 130W
Approx.0W
Approx.1.700W
(Room temperature = 20ûC)
Secondary
Terminal
Primary
Terminals
5-2 Low Voltage Transformer
1. The low voltage transformer is located on the
control circuit board.
2. Remove the low voltage transformer from the
PCB Ass'y and check continuity.
3. Normal resistor reading is shown in the table.
Terminals
Resistance
1~2(Input)
3~4(Output 2.9V)
5~6(Output13V)
1,000W
3.947W
2.117W
5-3 Magnetron
1. Continuity checks can indicate only an open
filament or a shorted magnetron. To diagnose an
open filament or shorted magnetron :
2. Isolate the magnetron from the circuit by
disconnecting its leads.
3. A continuity check across the magnetron filament
terminals should indicate one ohm or less.
4. A continuity check between each filament terminal
and magnetron case should read open.
Magnetron Antenna
Gasket Plate
Cooling Fins
Samsung Electronics
5-1
Alignment and Adjustments
5-4 High Voltage Capacitor
1. Check continuity of the capacitor with the meter set at the highest resistance scale.
2. Once the capacitor is charged, a normal capacitor shows continuity for a short time, and then indicates 9MW.
3. A shorted capacitor will show continuous continuity.
4. An open capacitor will show constant 9MW.
5. Resistance between each terminal and chassis should read infinite.
5-5 High Voltage Diode
1. Isolate the diode from the circuit by disconnecting its leads.
2. With the ohm-meter set at the highest resistance scale, measure across the diode terminals. Reverse the
meter leads and read the resistance. A meter with 6V, 9V or higher voltage batteries should be used to
check the front-to back resistance of the diode (otherwise an infinite resistance may be read in both
directions). The resistance of a normal diode will be infinite in one direction and several hundred KW in
the other direction.
5-6 Main Relay and Power Control Relay
1. The relays are located on the PCB Ass'y. Isolate them from the main circuit by disconnecting the leads.
2. Operate the microwave oven with a water load in the oven. Set the power level set to high.
3. Check continuity between terminals of the relays after the start pad is pressed.
5-7 Adjustment of Primary Switch, Door Sensing Switch and Monitor Switch
Precaution
For continued protection against radiation hazard, replace parts in accordance with the wiring diagram and be sure to use the
correct part number for the following switches: Primary and secondary interlock switches, and the interlock monitor switch
(replace all together). Then follow the adjustment procedures below. After repair and adjustment, be sure to check the continuity
of all interlock switches and the interlock monitor switch.
1. When mounting Primary switch and Interlock
Monitor switch to Latch Body, consult the figure.
2. No specific adjustment during installation of
Primary switch and Monitor switch to the latch
body is necessary.
3. When mounting the Latch Body to the oven
assembly, adjust the Latch Body by moving it so
that the oven door will not have any play in it.
Check for play in the door by pulling the door
assembly. Make sure that the latch keys move
smoothly after adjustment is completed.
Completely tighten the screws holding the Latch
Body to the oven assembly.
4. Reconnect to Monitor switch and check the
continuity of the monitor circuit and all latch
switches again by following the components test
procedures.
5. Confirm that the gap between the switch
housing and the switch actuator is no more than
0.5mm when door is closed.
5-2
Primary Interlock Switch
Interlock
Monitor
Switch
Lever Door(B)
Body Latch
Door Sensing
Switch
Primary switch
Monitor switch (COM-NC)
Monitor switch (COM-NO)
Door Sensing S/W
Door Open
¥
0
¥
¥
Door Closed
0
¥
0
0
Samsung Electronics
Alignment and Adjustments
5-8 Output Power of Magnetron
CAUTION
MICROWAVE RADIATION
PERSONNEL SHOULD NOT ALLOW EXPOSURE TO MICROWAVE RADIATION FROM MICROWAVE GENERATOR OR OTHER PARTS
CONDUCTING MICROWAVE ENERGY.
The output power of the magnetron can be measured by performing a water temperature rise test.
Equipment needed :
* Two 1-liter cylindrical borosilicate glass vessel (Outside diameter 190 mm)
* One glass thermometer with mercury column
NOTE: Check line voltage under load. Low voltage will lower the magnetron output. Make all temperature
and time tests with accurate equipment.
1. Fill the one liter glass vessel with water.
2. Stir water in glass vessel with thermometer, and record glass vessel's temperature ("T1", 10±1ûC).
3. After moving the water into another glass vessel, place it in the center of the cooking tray. Set the oven to high
power and operate for 54 seconds exactly. (2 seconds included as a holding time of magnetron oscillation:)
4. When heating is finished, stir the water again with the thermometer and measure the temperature ("T2").
5. Subtract T1 from T2. This will give you the water temperature rise. (DT)
6. The output power is obtained by the following formula;
Output Power =
4.187 x 1000 x DT
42
42 : Heating Time (sec)
4.187 : Coefficient for Water
1000 : Water (cc)
DT : Temperature Rise (T2-T1)
* Output (W) = 100 x DT
7. Normal temperature rise for this model is 9ûC to 11ûC at 'HIGH'.
NOTE 1: Variations or errors in the test procedure will cause a variance in the temperature rise.
Additional power test should be made if temperature rise is marginal.
NOTE 2: Output power in watts is computed by multiplying the temperature rise (step E) by a factor of 91
times the of centigrade temperature.
5-9 Microwave Heat Distribution - Heat Evenness
The microwave heat distribution can be checked indirectly by measuring the water temperature rise at
certain positions in the oven:
1. Prepare five beakers made of 'Pyrex', having 100 milliliters capacity each.
2. Measure exactly 100milliliters off water load with a measuring cylinder, and pour into each beaker.
3. Measure the temperature of each water load. (Readings shall be taken to the first place of decimals.)
4. Put each beaker in place on the cooking tray as illustrated in figure below. Start heating.
5. After heating for 2 minutes, measure the water temperature in each beaker.
6. Microwave heat distribution rate can be calculated as follows:
Heat Distribution =
Minimum
Temperature Rise
Maximum
Temperature Rise
D
X 100(%)
Beaker
D
D/4
The result should exceed 65%.
D/4
D/4
D/4
Samsung Electronics
Cooking Tray
5-3
Alignment and Adjustments
5-10 Procedure for Measurement of Microwave Energy Leakage
1) Pour 275¡ 15cc of 20¡ 5¡ ( 68¡ 9¢ ) water in a
beaker which is graduated to 600cc, and place the
beaker in the center of the oven.
2) Start to operate the oven and measure the leakage by
using a microwave energy survey meter.
3) Set survey meter with dual ranges to 2,450MHz.
4) When measuring the leakage, always use the 2 inch
spacer cone with the probe. Hold the probe
perpendicular to the cabinet door. Place the spacer
cone of the probe on the door and/or cabinet door
seam and move along the seam, the door viewing
window and the exhaust openings moving the
probe in a clockwise direction at a rate of 1 inch/sec. If the leakage testing of the cabinet door seam is
taken near a corner of the door, keep the probe perpendicular to the areas making sure that the probe end
at the base of the cone does not get closer than 2 inches to any metal. If it gets closer than 2 inches,
erroneous readings may result.
5) Measured leakage must be less than 4mW/cm2, after repair or adjustment.
1.
2.
3.
1.
2.
3.
Auto
Auto
1.
2.
3.
Auto
1 min +
Maximum allowable leakage is 5mW/cm2.
4mW/cm2 is used to allow for measurement and meter accuracy
5-11 Check for Microwave Leakage
1. Remove the outer panel.
2. Pour 275±15cc of 20±5ûC(68±9ûF) water in a beaker
which is graduated to 600cc, and place the beaker in
the center of the oven.
3. Start the oven at the highest power level.
4. Set survey meter dual ranges to 2,450MHz.
5. Using the survey meter and spacer cone as described
above, measure arnear the opening of magnetron, the
surface of the air guide and the surface of the wave
guide as shown in the following photo.( but avoid the
high voltage components.) The neading should be less
than 4mW/cm2.
5-12 Note on Measurement
1) Do not exceed the limited scale.
2) The test probe must be held on the grip of the handle, otherwise a false reading may result when the
operator's hand is between the handle and the probe.
3) When high leakage is suspected, do not move the probe horizontally along the oven surface; this may
cause damage to the probe.
4) Follow the recommendation of the manufacturer of the microwave energy survey meter.
5-13 Leakage Measuring Procedure
5-13-1 Record keeping and notification after measurement
1) After adjustment and repair of a radiarion preventing device, make a repair record for the measured
values, and keep the data.
2) If the radiation leakage is more than 4 mW/§† after determining that all parts are in good condition,
functioning properly and the identical parts are replaced as listed in this manual notift that fact to ;
CENTRAL SERVICE CENTER
5-13-2 At least once a year have the microwave energy survey meter checked for accuracy by its
manufacturer.
5-4
Samsung Electronics
6. Troubleshooting
PRECAUTION
1. CHECK GROUNDING BEFORE CHECKING FOR TROUBLE.
2. BE CAREFUL OF THE HIGH VOLTAGE CIRCUIT.
3. DISCHARGE THE HIGH VOLTAGE CAPACITOR.
4. WHEN CHECKING THE CONTINUITY OF THE SWITCHES OR TRANSFORMER, DISCONNECT ONE LEAD WIRE FROM THESE
PARTS AND THEN CHECK CONTINUITY WITHOUT THE POWER SOURCE ON. TO DO OTHERWISE MAY RESULT IN A FALSE
READING OR DAMAGE TO YOUR METER.
5. DO NOT TOUCH ANY PART OF THE CIRCUIT OR THE CONTROL CIRCUIT BOARD, SINCE STATIC DISCHARGE MAY DAMAGE IT.
ALWAYS TOUCH GROUND WHILE WORKING ON IT TO DISCHARGE ANY STATIC CHARGE BUILT UP.
6-1 Electrical Maltunction
SYMPTOM
CAUSE
CORRECTIONS
Oven is dead.
Fuse is OK.
No display and no operation at all.
1. Open or loose lead wire harness
2. Open thermal cutout (Magnetron)
3. Open low voltage transformer
4. Defective Ass'y PCB
Check fan motor when thermal cutout is defective.
No display and no operation at all.
Fuse is blown.
1. Shorted lead wire harness
2. Defective primary latch switch (NOTE 1)
3. Defective monitor switch (NOTE1)
4. Shorted HVCapacitor
5. Shorted HVTransformer (NOTE2)
Check adjustment of primary, interlock monitor,
door sensing switch.
Check Ass'y PCB when LVT is defective.
NOTE 1: All of these switches must be replaced at the same time.
(refer to adjustment instructions)
Check continuity of power relay contacts and if it has continuity, replace power
relay also.
NOTE 2: When HVTransformer is replaced, check diode and magnetron also.
Oven does not accept
key input (Program)
Timer starts countdown but no
microwave oscillation.
(No heat while oven lamp and
fan motor turn on.)
Samsung Electronics
1. Key input is not in-Sequence
2. Open or loose connection of membrane
key pad to Ass'y PCB
3. Shorted or open membrane panel
4. Defective Ass'y PCB
Refer to operation procedure.
1. Off-alignment of latch switches
2. Open or loose connection of high voltage
circuit especially magnetron filament
circuit
NOTE: Large contact resistance will bring
lower magnetron filament voltage and
cause magnetron to lower output and/or
intermittent oscillation.
3. Defective high voltage components
H.V.Transformer
H.V.Capacitor
H.V.Diode, H.V.Fuse
Magnetron
4. Open or loose wiring of power relay
5. Defective primary latch switch
6. Defective power relay or Ass'y PCB
Adjust door and latch switches.
Replace PCB main.
Check high voltage component according to
component test procedure and replace if it is
defective.
Replace PCB main.
6-1
Troubleshooting
6-1 Electrical Maltunction(continved)
SYMPTOM
CAUSE
CORRECTIONS
Oven lamp and fan motor turn on
1. Misadjustment or loose wiring
of primary latch switch
2. Defective primary latch switch
Adjust door and latch switches.
Oven can program but timer
does not start.
1. Open or loose wiring of secondary
interlock switch
2. Off-alignment of primary interlock
3. Defective secondary interlock S/W
Adjust door and interlock switches.
Microwave output is low;.
Oven takes longer time to
cook food.
1. Decrease in power source voltage.
2. Open or loose wiring of magnetron
filament circuit. (Intermittent oscillation))
3. Aging of magnetron
Consult electrician.
Fan motor turns on when plugged in
Loose wiring of door sensing switch
Check wire of door sensing switch.
Oven does not operate and return
to the plugged in mode.
Defective Ass'y PCB
Replace PCB main.
Loud buzzing noise can be heard.
1. Loose fan and fan motor
2. Loose screws on H.V.Transformer
3. Shorted H.V.Diode
Tighten screws of fan motor.
Tighten screws of H.V.Transformer.
Replace H.V.Diode.
Turntable motor does not rotate.
1. Open or loose wiring of turntable motor.
2. Defective turntable motor.
Replace turntable motor.
Oven stops operation during cooking
1. Open or loose wiring of primary
interlock switch
2. Operation of thermal cutout(Magnetron)
Adjust door and latch switches.
Sparks
1. Metallic ware or cooking dishes
touching on the oven wall.
2. Ceramic ware trimmed with gold or
silver powder also causes sparks.
Inform the customer.
Do not use any type of cookware with
metallic trimming.
Uneven cooking
Uneven intensity of microwave due to
its characteristics.
Wrap thinner parts of the food with
aluminum foil.
Use plastic wrap or cover with a lid.
Stir once or twice while cooking
foods such as soup, cocoa, or milk.
Noise from the turntable motor
when it starts to operate.
Noise may result from the motor.
Replace turntable motor.
6-2
Samsung Electronics
7. Exploded Views and Parts List
7-1 Exploded Views
D6
D11
D3
D5
D4
D7
M1
D8
M2
D9
D10
D12
M3
M30
D1
M4
D2
M13
M25
M5
M7
M11
M6
M24
NC
NO
COM
M23
M14
M21
M10
M30
B1
M8
M15
M26
M9
B2
B3
M22
B4
B2
M12
C7
C15
C3
C2
M17
C4
M16
C5
C6
C10
C9
M19
C8
M18
C11
C1
C12
M20
M27
C13
C14
M28
M29
Samsung Electronics
7-1
Exploded Views and Parts List
7-2 Main Parts List
Ref. No.
Parts No.
M 1
DE70-30001A
M 1
Description/Specification
Q'ty
Remarks
PANEL-OUTER;SECC T0.6 360 1128 EPOXY-COATIN
1
WHITE
DE70-30001E
PANEL-OUTER;SECC T0.6 360 1128 W/RED RE-44
1
RED
M 1
DE70-30001I
PANEL-OUTER;SECC T0.6 360 1128 DEEP/GRN MX
1
GREEN
M 2
DE63-90035G
CUSHION-RUBBER;DFA20 T2 W190 L100 BLK
1
M 3
DE39-20054C
ASSY POWER CORD;KKP-4819D/B206 250V10A L150
1
M 4
DE39-40537A
WIRE HARNESS-A;230V50HZ M945(SAW)
1
M 5
DE91-40093A
ASSY NOISE FILTER;SN-E10D 250V 10A
1
M 6
DE31-10156A
MOTOR-FAN;SMF-945EA 230/50 2400 M97G45
1
M 7
DE47-20009A
THERMOSTAT;CS-7SA (160/60) 187Y 250V7.5A 160
1
M 8
DE03-30035A
MAGNETRON;OM75PH(31)ESS
1
M 9
DE93-20020A
ASSY BODY LATCH;RE-43B/90B
1
M 10
4713-001004
LAMP-INCANDESCENT;230V,-,40W,ORG,-,-,25x
1
M 11
DE61-50490A
BRACKET-TCO;SECC1 T0.6 34 58
1
M 12
DE71-60016A
COVER-AIR;PP 2 WHT M945/MB45
1
M 13
DE91-70101C
ASSY-THERMOSTAT;MW5574W 160/60 187-HORIZ
1
M 14
DE73-90027A
FERRITE CORE;NI-ZN T13.8 W21.0 L28.0 BNF 14
1
M 15
DE26-10100A
TRANS-H.V;SHV-945EG1 230V 50HZ 2310V DPC
1
M 16
DE61-50106A
BRACKET-HVC;SECC T0.8 W31 L125.8
1
M 17
2501-001019
C-OIL;1.01uF,2100V,BK,35x54x90,20mm
1
M 18
DE59-40001A
DIODE-H.V;HVR-1X-32B-12
1
M 19
DE91-70061A
ASSY-H.V.FUSE;THV060T-0800-H 5KV/0.8A WHT
1
M 20
DE61-40017A
FOOT;PP(A353) BLK MW5630T
2
M 21
DE31-10154A
MOTOR-DRIVE;M2HJ49ZR02,ST-16 1V 5/6
1
M 22
DE80-10001A
BASE-PLATE;SGCC T0.8 345 565
1
M 23
DE47-20008A
THERMOSTAT;PW2N-52JC 100/60 250V/7.5A H
1
M 24
DE71-60382A
COVER-CEILING;MICASHEET T0.5 70 133
1
M 25
ASSY DOOR;M959/AMF WHT BASIC
1
WHITE
M 25
ASSY DOOR;M959C/AMF RED
1
RED
M 25
ASSY DOOR;M959GR/XEF GREEN
1
GREEN
M 26
ASSY CONTROL-BOX;230V50HZ M959 WHT
1
WHITE
M 26
ASSY CONTROL-BOX;230V50HZ M959CAMF RED
1
RED
M 26
ASSY CONTROL-BOX;230V50HZ M959GR/XEF GRN
1
GREEN
M 27
DE74-20015B
TRAY-COOKING;GLASS T6.0 PI318 1050G MW5630T
1
M 28
DE92-90189D
ASSY-GUIDE ROLLER;D19 STD
1
M 29
DE67-60075A
COUPLER;PPS 7G BRN M97G45
1
M 30
DE63-90065N
CUSHION-GUIDE;PUT-FOAM T10 W10 L200 BLK MW55
1
M 31
DE63-90065O
CUSHION-GUIDE;PUT-FOAM T35 W20 L135 VBLK MW55
1
: Option Parts
7-2
: Warning
:Electrostatically Sensitive Devices
Samsung Electronics
Exploded Views and Parts List
7-3 Door Parts List
Ref. No.
Parts No.
Description / Specification
D 1
D 1
D 1
D 2
D 3
D 3
D 3
D 4
D 5
D 5
D 6
D 7
D 8
D 8
D 9
D 10
D 11
D 12
D 12
D 12
DE64-20112D
DE64-20112C
DE64-20112E
DE01-00098A
DE64-40263F
DE64-40263G
DE64-40263H
DE67-20265D
DE92-50127H
DE92-50127F
DE64-40012A
DE01-00002B
DE61-70126A
DE61-70032A
DE64-40264A
DE61-80003A
DE61-80002A
DE92-40197A
DE92-40198A
DE92-40198B
HANDLE-DOOR;ABS(HR0370U) 30G WHT M959
HANDLE-DOOR;ABS BLK 30G RE-447
HANDLE-DOOR;ABS(HR0370D) 30G GRN M959GR
FILM-DOOR;PET T0.13 W22.6 L201.8
DOOR-A;ABS(HR-0370U) 160G WHT M959
DOOR-A;ABS(HR-0370U) 160G GRN M959GR NE
DOOR-A;ABS(HR-0370D) 160G GRN M959GR NE
DOOR-SCREEN;ACRYL (IF850)ED17 M959
ASSY DOOR-E;COATING BLACK T0.8
ASSY DOOR-E;BLK COATING DOOR-E/T0.8
DOOR-C;RESIN-PP(TB53) T2.0 CE945GF BLA
FILM-DOOR;PC T0.15 275 175 MW5574W
SPRING-KEY;0.8 0.36 6 BLUING
SPRING-KEY;ES MSWR PI0.6 D5.4 L25 MW8640T
DOOR-KEY;POM(HANDLE) T.25 W51 L40 40G
HINGE-LOWER;SCP1 T2.3 26 77 ZPC3 WHT CHR
HINGE-UPPER;SCP1 T2.3 26 77 ZPC3 WHT CHR
ASSY DOOR-A;M959 WHT
ASSY DOOR-A;M959C RED
ASSY DOOR-A;M959GR.XEF GRN
Q'ty
Remarks
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
WHITE
RED
GREEN
WHITE ONLY
WHITE
RED
GREEN
Remarks
WHITE/RED
GREEN
WHITE/RED
GREEN
WHITE
RED
GREEN
7-4 Standard Parts List
Parts No.
Description / Specification
Q'ty
DE60-10012A
DE60-10012A
DE60-10012A
DE60-10033A
DE60-10033A
DE60-10045A
DE60-10080A
DE60-10080A
DE60-10082H
DE60-10082H
DE60-10082H
DE60-10082H
DE60-10082H
DE60-10082H
DE60-10098A
DE60-10098A
DE60-10045A
DE60-10066A
DE60-10012A
DE60-10098A
SCREW-TAP TITE;TH,+,3,M4,L10,SWR10,ZPC2,TOOTH
SCREW-TAP TITE;TH,+,3,M4,L10,SWR10,ZPC2,TOOTH
SCREW-TAP TITE;TH,+,3,M4,L10,SWR10,ZPC2,TOOTH
SCREW-TH;TH,+,M4,L10,MSWR10,FEFZY
SCREW-TH;TH,+,M4,L10,MSWR10,FEFZY
SCREW-TAP PH;PH,M3,L6,FEFZY
SCREW-WASHER;M5,L12,2S
SCREW-WASHER;M5,L12,2S
SCREW-A;2S-4X12,TOOTHED
SCREW-A;2S-4X12,TOOTHED
SCREW-A;2S-4X12,TOOTHED
SCREW-A;2S-4X12,TOOTHED
SCREW-A;2S-4X12,TOOTHED
SCREW-A;2S-4X12,TOOTHED
SCREW-ASSY TAP TITE;PH,TC,M4X8,SWRCH18A,ZPC2,GLD,W
SCREW-ASSY TAP TITE;PH,TC,M4X8,SWRCH18A,ZPC2,GLD,W
SCREW-TAP PH;PH,M3,L6,FEFZY
SCREW-TAP TH;TH,M4,L8,FEFZY,2-SLOT
SCREW-TAP TITE;TH,+,3,M4,L10,SWR10,ZPC2,TOOTH
SCREW-ASSY TAP TITE;PH,TC,M4X8,SWRCH18A,ZPC2,GLD,W
1
1
1
2
2
2
4
4
5
2
2
2
1
2
1
2
1
2
1
1
Samsung Electronics
P-C-EA
S-M-EA
N-F-EA
HI-LOW
HI-UPP
MG-TCO
TNS-HV
TNS-HV
PN/OUT
B-PLTE
BD-LAT
CN-BOX
CV/AIR
MO/FAN
CV-TCO
M/GEAR
H/DOOR
B/D-MO
B/HVC
7-3
Exploded Views and Parts List
7-5 Control Parts List
Ref. No.
Parts No.
C 1
C 1
C 1
C 2
C 3
C 3
C 3
C 4
C 4
C 4
C 5
C 5
C 5
C 6
C 6
C 6
C 7
C 8
C 9
C 9
C 9
C 10
C 10
C 10
C 11
C 11
C 11
C 12
C 12
C 12
C 13
C 14
C 14
C 14
C 15
C 15
C 15
DE71-60366F
DE71-60366G
DE71-60366K
DE67-40145A
DE72-70171G
DE72-70171H
DE72-70171Q
DE66-20174R
DE66-20174S
DE66-20174T
DE66-20197J
DE66-20197K
DE66-20197L
DE66-20198J
DE66-20198K
DE66-20198L
DE66-20179A
DE91-10502A
DE66-20175E
DE66-20175D
DE66-20175F
DE66-20176E
DE66-20176D
DE66-20176F
DE66-20177E
DE66-20177B
DE66-20177F
DE66-20178E
DE66-20178B
DE66-20178F
DE61-70126A
DE66-20173E
DE66-20173F
DE66-20173M
DE93-30406G
DE93-30406H
DE93-30406Q
Description/Specification
COVER-PANEL;ABS(HR0370U) 45G WHT M95
COVER-PANEL;ABS-HR0370 45G BLK M959C
COVER-PANEL;ABS(HR0370D) GRN M959GR/XEF
WINDOW-DISPLAY;ACRYL T2 W40 L77 SMOG 30G
CONTROL-PANEL;ABS(HR0370U) WHT 160G M9
CONTROL-PANEL;ABS-HR0370 RED 160G M959
CONTROL-PANEL;ABS GRN M959/XEF
BUTTON-SELECT-A;PC 2G WHT M959
BUTTON-SELECT-A;PC 2G WINE-RED M759C
BUTTON-SELECT-A;PC 2G DEEP-GRN M759GR
BUTTON-SELECT(A-B);PC 2G WHT M959
BUTTON-SELECT(A-B);PC 2G WINE-RED M759C
BUTTON-SELECT(A-B);PC 2G DEEP-GRN M759GR
BUTTON-SELECT(A-C);PC 2G WHT M959
BUTTON-SELECT(A-C);PC 2G WINE-RED M759C
BUTTON-SELECT(A-C);PC 2G DEEP-GRN M759GR
BUTTON-SELECT;ABS(HR0370) NTR 30G RE-445
ASSY PCB-MAIN;RC-M959-00 230V50HZ LED M959
BUTTON-SELECT-B;ABS(HR0370U) 5G, WHT M959
BUTTON-SELECT-B;ABS(HR0370) BLK 5G RE-446
BUTTON-SELECT-B;ABS(HR0370D) 5G GRN M959GR
BUTTON-SELECT-C;ABS(HR0370U) 5G, WHT M959
BUTTON-SELECT-C;ABS(HR0370) BLK 5G RE-446
BUTTON-SELECT-C;ABS(HR0370) 5G GRN M959GR
BUTTON-SELECT-D;ABS(HR0370U) 3G, WHT M959
BUTTON-SELECT-D;ABS(HR0370) RED 3G RE-445R
BUTTON-SELECT-D;ABS(HR0370D) 2G GRN M959GR/XEU
BUTTON-SELECT-E;ABS(HR0370U) WHT 2G M959
BUTTON-SELECT-E;ABS(HR0370) RED 3G RE-445R
BUTTON-SELECT-E;ABS(HR0370D) 2G GRN M959GR
SPRING-KEY;0.8 36 6 BLUING
BUTTON-START;ABS(HR0370U) 7G WHT M959
BUTTON-START;ABS(HR0370) 7G RED M959C
BUTTON-START;ABS GRN M959GR/XEF
ASSY CONTROL-PANEL;M959 WHT
ASSY CONTROL-PANEL;240V50HZ M959C RED
ASSY CONTROL-PANEL;230V50HZ M959GR/XEF GRN
Q'ty
Remarks
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
WHITE
RED
GREEN
Q'ty
Remarks
WHITE
RED
GREEN
WHITE
RED
GREEN
WHITE
RED
GREEN
WHITE
RED
GREEN
WHITE
RED
GREEN
WHITE
RED
GREEN
WHITE
RED
GREEN
WHITE
RED
GREEN
WHITE
RED
GREEN
WHITE
RED
GREEN
7-6 Body Latch Parts List
Ref. No
B
B
B
B
7-4
1
2
3
4
Parts No.
Description / Specification
DE66-40021A
3405-000178
3405-000175
DE66-90054A
LATCH-BODY;POM(F20-02) 50GR RE-330
SWITCH-MICRO;250V,15A,200gf,SPST-NO
SWITCH-MICRO;250V,15A,200gf,SPST-NO
LEVER-SWITCH;POM(F20-02) 15G NTR RE-330
1
2
1
1
Samsung Electronics
8. P.C.B Diagrams
8-1 P.C.B Diagrams
Samsung Electronics
8-1
P.C.B Diagrams
8-2 P.C.B Parts List
Parts No.
1003-001033
3501-001050
3501-001062
3710-000246
DE07-20133A
DE09-30650A
DE13-20016A
DE26-20146A
DE30-20016A
DE37-90019A
0401-001025
0402-001188
0403-000717
0501-000283
0501-000388
0504-001014
2001-000273
2001-000290
2001-000429
2001-000502
2001-000577
2001-000613
2001-000904
2202-000780
2401-000247
2401-000876
2401-000914
2401-001362
2802-000161
3404-000282
3711-000203
3711-000240
3711-000881
DE13-20009A
DE39-60001A
DE60-60012A
8-2
Description / Specification
IC-SOURCE DRIVER;TD62781AP,DIP,18P,300MIL,OCTAL
RELAY-MINIATURE;24VDC,200mW,5A,1FormA,10mS,5mS
RELAY-POWER;24VDC,523.2mW,16A,1FormA,15mS
CONNECTOR-SOCKET;9P,1R,2.5mm,STRAIGHT,SN
LED DISPLAY;ODG-404ADL,GRN,5,22,H24,RE-445
IC-MCU;KS57C0004-G6E,4,DIP,4,-,M959
IC-VOLT REGU;KA7805A,TO-220AB,1A,0/125C
TRANS-L.V;SLV-745EN,230V,50HZ,AC17/7V
BUZZER;CBE2220BA,STICK
CONNECTOR ASSY;YJN25009,PLATE,73MM,WHT
DIODE-SWITCHING;1N4148M,50V,450mA,DO-34,TP
DIODE-RECTIFIER;1T4(TP26),400V,1A,TS-1,TP
DIODE-ZENER;MTZJ5.1B,5.1V,4.94-5.2V,500mW
TR-SMALL SIGNAL;KSA539,PNP,400mW,TO-92,TP,120
TR-SMALL SIGNAL;KSC815,NPN,400mW,TO-92,BK,120
TR-DIGITAL;KSR1005,NPN,300mW,4.7K-10K,TO
R-CARBON;100Kohm,5%,1/8W,AA,TP,1.8x3.2m
R-CARBON;10Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R-CARBON;20ohm,5%,1/4W,AA,TP,2.4x6.4mm
R-CARBON;2Kohm,5%,1/8W,AA,TP,1.8x3.2mm
R-CARBON;3.9Kohm,5%,1/8W,AA,TP,1.8x3.2m
R-CARBON;620ohm,5%,1/8W,AA,TP,1.8x3.2mm
C-CERAMIC,MLC-AXIAL”;100nF,+80-20%,50V,Y5V,TP,3.5x1
C-AL;100uF,20%,10V,GP,-,6.3x11mm,5m
C-AL;220uF,20%,50V,GP,TP,13x20mm,5m
C-AL;22uF,20%,16V,-,TP,5x11,5mm
C-AL;470uF,20%,16V,GP,-,10x12.5mm,5
RESONATOR-CERAMIC;4MHz,0.5%,TP,10.0x5.0x7.5mm
SWITCH-TACT;12Vdc,50mA,120+-30gf,6.2x3.6mm
CONNECTOR-HEADER;1WALL,3P,1R,3.96mm,ANGLE,SN
CONNECTOR-HEADER;1WALL,4P,1R,3.96mm,STRAIGHT,SN
CONNECTOR-HEADER;BOX,3P,1R,2.5mm,STRAIGHT,SN
IC;KA7533,DIP
WIRE-SO COPPER;PI0.6,SN,T,52MM,TAPING_WIRE
PIN-EYELET;ID2.1,OD2.5,L3.0,SN,BSP,T0.25
Q'ty
1
2
1
1
1
1
1
1
1
1
10
3
1
1
2
4
1
9
5
7
2
3
1
4
1
1
1
1
1
10
1
1
1
1
10
6
Remarks
IC02
RY02,RY03
RY01
CN05
LED1
IC01
IC04
LVT1
BUZ1
CN04
D04~D13
D1~03
ZD01
TR03
TR01,TR04
TR02,TR05,TR06,TR08
R15
R05~R07,R10,R12,R13,R19~R21
R01,R02,R08,R11,R17
R22~R28
R03,04
R09,R14,R16
R18
C05~C08
C03
C01
C04
C02
XTL1
SW01~SW10
CN01
CN02
CN03
IC03
J01~J10
Samsung Electronics
9. Schematic Diagrams
9-1 Schematic Diagrams
ASSY NOISE FILTER
LAMP
(230V40W)
L.V.TRANS
2200pF
500K
BLK
H.V.T
L
FM
YEL
YEL
0V
H.V.D
ORG
230V
21V
DM
H.V.FUSE
MONITOR
SWITCH
0V
ORG
H.V.C
BLU
E
YEL
MONITOR
FUSE
2200pF
BRN
BLU
MAIN
RELAY
C2
VOLTAGE
FREG
BLU
1mH
PRIMARY
SWITCH
CAVITY
TCO BRN
BLK
C1
MAIN FUSE
E
BRN
BRN
LIN-CAPACITORT 0.1uF
230V~
50Hz
MGT
TCO
RESISTOR
INRUSH RELAY
WHT
F
YEL
FA
BLU
BLU
POWER RELAY
NOTE
PRIMARY
LATCH
SWITCH
Samsung Electronics
BLU YEL
BLU BLK
BRN
ORG
DOOR
SENSING
SWITCH
NO
COM NO
ASSY MAIN P.C.B
ORG
ORG
COM NO
MAIN INRUSH POWER
RELAY RELAY RELAY
BRN
L.V.T
BRN BLK
MAGNETRON
DOOR
SENSING
SWITCH
COM NO
1. INPUT : 230V
2. DOOR : OPEN
3. LAMP : ON
4.
: P.C.B PATTERN
5.
: P.C.B IN/OUT
POINT
MONITOR
SWITCH
SYMBOL
BRN
BLU
ORG
RED
WHT
BLK
YEL
GRN
Y/G
COLOR
BROWN
BLUE
ORANGE
RED
WHITE
BLACK
YELLOW
GREEN
YELLOW/GREEN
9-1