VKI Technologies Eccellenza cafe Service manual

Service Manual
Customer Service – 800.567.2951
VKI Publication# 100285-001
Technical Support – 888.854.0207
May 2015
Eccellenza Pod
2
Eccellenza Pod
Table of Contents
Contents
Safety Information .............................................................................. 4
Specifications ...................................................................................... 6
Equipment Overview ........................................................................... 7
Rinse Cycles ........................................................................................ 9
Powder Rinse Cycle ........................................................................... 9
Brewer Rinse .................................................................................... 9
Maintenance ...................................................................................... 10
Daily.............................................................................................. 10
Weekly .......................................................................................... 10
Monthly ......................................................................................... 11
Every 6-12 Months .......................................................................... 11
Every 18 Months ............................................................................. 11
Sanitization – Milk System ............................................................... 12
Cleaning the Vacuum Duct (Powder System) ...................................... 13
Removing the Rear Panel .................................................................. 14
Removing the Top Panel .................................................................... 15
Removing the Front Panel ................................................................. 16
Draining the Water Tank ................................................................... 20
Replacing Components ...................................................................... 21
Brewer ........................................................................................... 21
Powder Dispensers .......................................................................... 23
Powder Dispenser Motors ................................................................. 25
Power Supply.................................................................................. 29
Control Board ................................................................................. 31
Connector Layout on the Control Board ......................................... 33
Selection Board or LCD Display ......................................................... 34
Water Tank .................................................................................... 39
Outlet Valve Manifold ....................................................................... 42
Disassembling the Dual Valve Manifold ......................................... 44
Disassembling an Outlet Valve ..................................................... 45
Inlet Valve ..................................................................................... 47
Air Pump ........................................................................................ 49
Replacing the Inline Check Valve .................................................. 50
Water Pump ................................................................................... 51
Powder Dispenser and Waste Bin Detection Switches ........................... 53
Whipper Motor ................................................................................ 54
Whipper Vacuum Fan ....................................................................... 59
Exhaust Fan ................................................................................... 61
Main Power Components .................................................................. 62
Fuse Holder (15 Amp) ................................................................. 63
Service Cord .............................................................................. 63
Main Power Switch ..................................................................... 64
Installing the Coin Changer System .................................................. 65
Install the Coin Changer Assembly .................................................... 68
Test the Machine and the Coin Changer System .................................. 69
Updating Equipment Firmware .......................................................... 70
Software Installation ....................................................................... 70
Hardware Installation ...................................................................... 70
Loading Programs onto the Load-n-Go Programmer ............................. 71
Loading New Firmware into the Eccellenza Pod ................................... 74
Error Messages.................................................................................. 77
Wiring Diagram ................................................................................. 79
Information in this document is subject to change without notice.
3
Eccellenza Pod
Safety Information
Safety Information
Your safety is very important to us. It is imperative that you read and understand
this safety information before proceeding with the installation, operation or servicing
of this coffee maker.
This equipment must be used specifically for the purpose for which
it is designed. The manufacturer is not responsible for damage or
injury resulting from improper use of this equipment.
Always switch the machine power OFF and disconnect the
service cord from the wall outlet when servicing this
equipment, unless stated otherwise.
 This coffee maker is designed for indoor use ONLY and must never be
installed outdoors.
 The installation of this equipment must comply with all municipal,
state/provincial, and federal electrical and plumbing codes.
 Installation and servicing of this equipment must only be performed
by qualified personnel. Do not attempt to install or service this equipment if
you are not qualified as it may result in personal injury. There are no userserviceable parts inside the equipment.
 Do not attempt to lift or move this equipment by yourself. Use a hydraulic lift
(or similar) or have a colleague provide assistance.
 This equipment must be installed in a location with an ambient temperature
between 5°C-35°C (40°F-95°F).
 The main water supply pressure must be between a minimum of 20psi and a
maximum of 100psi.
 This equipment must be positioned so that the wall plug and the main power
switch are both easily accessible.
 Do not connect the coffee maker to a voltage supply other than the voltage
indicated on the serial number decal.
 Do not immerse this coffee maker or any part of this equipment in liquid.
 Do not install the equipment in an area where water spray is present.
 This coffee maker must be installed securely on a level surface. If it does not
appear to be a stable location, select another installation location.
 Keep hands clear of the dispensing area at the front of the coffee maker.
Liquids being dispensed are extremely hot and can cause severe
burns.
 Never disconnect the coffee maker by pulling on the service cord, and never
use the coffee maker if the service cord is damaged.
4
Eccellenza Pod
Safety Information
 If the service cord is damaged, it must be replaced with a new service
cord that is available from your distributor or the manufacturer of this
equipment.
 This equipment uses low voltage DC powered valves and motors. Do not
connect components to a voltage supply other than the voltage indicated on
their specifications.
 Never attempt to override the safety features incorporated into the
equipment. They are there for your protection and should never be bypassed
under any circumstances.
 Always switch the power off and disconnect the service cord when cleaning the
interior of the coffee maker. Components inside the coffee maker can cause
electrical shock resulting in personal injury.
 If the coffee maker is not working properly or appears to have a fault, switch
off the power, disconnect the service cord and call an authorized technician
immediately for service. Only qualified personnel should perform service
on this equipment.
 Use caution when servicing the water heater or the outlet valves as they may
be extremely hot and can cause severe burns.
 Use caution when working inside the coffee maker as there may be sharp
edges on some components that can cause cuts.
 To prevent electrical shock, remove all jewelry (rings, watches, etc.) when
servicing the coffee maker.
 Do not allow children to access this equipment. They are not aware of the
potential dangers that exist.
 Never use ammonia based cleaners on machine surfaces as they will become
discolored and/or damaged permanently. Use milder cleaning products, such
as dish soap.
Unauthorized modifications made to this coffee maker can
result in serious personal injury and/or damage to the
equipment, and voids all warranties and certifications.
5
Eccellenza Pod
Specifications
Specifications
Voltage Rating
120 Volts AC @ 60hz (120 Volt Model)
Heater Wattage
1400 Watts
Weight (empty)
55 lbs (25 kg)
Powder Capacity (2)
Milk - 1 lb (450g)
Chocolate – 1.2 lb (550g)
Cup Sizes
3
Brew Time per Cup
Less than 60 seconds
Water Tank Capacity
0.79 gallons (3 liters)
Waste Bin Capacity
50 Pods
Temperature Control
Electronic Probe
Heating Time
Approx. 15 minutes after installation
Brew Temperature
198°F (92°C)
Heater Protection
Yes
Overflow Protection
Yes
Circuit Protection
Yes
Certifications/Listings
cCSAus
Coffee Maker Dimensions
Height:
17.8” (45 cm)
Width:
15”
(38 cm)
Depth:
21 ”
(53 cm)
Minimum Installation Requirements
Height:
18”
(45.5 cm)
Width:
15”
(38 cm)
Depth:
24”
(61 cm)
NOTE: This machine is factory preset with U.S. settings (Preset 1).
To change this preset, follow the instructions in the “Presets” section
on page 28 of the Eccellenza Pod Operating manual.
NOTE: Any references made in this manual to coffee blends and powder
products are for example purposes only. The actual products used in the
equipment may be different than the examples used in this manual.
6
Eccellenza Pod
Equipment Overview
Equipment Overview
LCD Display
(2 x 20 characters)
Strength Selection Buttons
(Regular or Bold)
Cup Size Selection Buttons
(Small, Regular, Large)
Front Fascia and
Beverage Selection Area
START button
(starts brewing process)
Door Lock
LCD Screen
Pod Door
Selection
Panel
Cup Stand /
Drip Tray
7
Eccellenza Pod
Equipment Overview
Powder
Hoppers
Door Lock
Pod Door
Set-Up Button
Whipper
Waste Bin
Cup Stand / Drip
Tray
Exhaust Fan
Main Power
Switch
Service Cord
Water Inlet
Valve
15A Fuse
8
Eccellenza Pod
Rinse Cycles
Rinse Cycles
WARNING: Place a large cup under the dispensing spout area to
catch the water that is dispensed during the rinse cycle.
Powder Rinse Cycle
NOTE: The powder rinse cycle is triggered automatically and is
mandatory after removing and replacing the powder hoppers, or if the
waste bin is removed for more than 10 seconds (default setting).
To access the powder rinse cycle,
1. Enter the Set-Up mode and scroll to the Powder Rinse menu.
2. Place a large cup or leak-proof container under the dispensing spout.
3. Press the Enter () button to begin the rinse cycle.
4. Repeat step #3 if more rinsing is required.
NOTE: The Powder System rinse menu automatically appears after the powder hoppers
have been removed, refilled and replaced. Performing this cycle is mandatory and once
it is completed, the machine will automatically revert to Standby (ready) mode.
Brewer Rinse
1. Select the coffee beverage and press the Enter () button to open the
brewer.
2. Instead of inserting a coffee pod into the brewer, insert the special brewer
cleaning tablet into the brewer.
3. Press the Enter () button to activate the vend cycle.
The hot water dissolves the cleaning tablet, which in turn cleans all of the
areas in the brewer system with which it comes into contact.
4. Make several vends afterwards (without inserting anything into the brewer) to
rinse out the cleaning solution.
5. Make one final vend using a coffee pod to test the brewer.
9
Equipment Overview
Eccellenza Pod
Maintenance
To keep the equipment running efficiently and at peak performance, the following
maintenance procedures must be performed at their specified intervals. It is
recommended that equipment maintenance be scheduled at a time that would be the
least disruptive to your customers. Whenever possible, replace the components
requiring maintenance with new or refurbished ones, and then refurbish the older
components at your shop.
CAUTION: Never use ammonia based cleaners on machine
surfaces as they will become discolored and/or damaged
permanently. Use mild cleaning products, such as dish soap.
Daily
► Empty the Drip Tray – empty the contents of the drip tray and rinse the tray
and grill under clean running water.
► Empty the Waste Bin – empty the contents of the waste bin.
► Refill the Powder Hoppers – top off the powder hoppers.
► Perform a Whipper Rinse Cycle – this should be done immediately after
refilling the powder hoppers to flush any product that may have fallen into the
whipper.
► Wipe Exterior and Countertop – using the clean towel, wipe any coffee
grounds and spills from the exterior of the machine and the countertop.
Weekly
► Wipe Interior Walls and Door - using the clean towel, wipe any spills from
the interior of the machine and the front door.
► Perform a Whipper Rinse Cycle – this should be done immediately after
refilling the powder hoppers to flush any product that may have fallen into the
whipper.
► Wipe Exterior and Countertop – using the clean towel, wipe any coffee
grounds and spills from the exterior of the machine and the countertop.
10
Eccellenza Pod
Maintenance
Monthly
► Clean the Whipper System – disassemble the whipper system and clean the
components with hot water.
► Clean the Brewer – to clean the brewer, make a vend as you normally
would, however, instead of inserting a coffee pod into the brewer, you need to
insert a special cleaning tab. The hot water dissolves the cleaning tab, which
in turn cleans all of the areas in which it comes into contact. Make several
vends afterwards (without inserting anything into the brewer) to rinse out the
cleaning solution. Make one final vend using a coffee pod to test the brewer.
► Clean Hoses and Spouts – clean the exterior of all the product hoses and
spouts with a wet towel.
► Thoroughly Clean the Interior – clean the interior walls, base and
components with a clean wet towel.
Every 6-12 Months
► Clean the Powder Hoppers – the hoppers should be emptied of product and
given a thorough cleaning to remove stains and deposits that may have
accumulated inside them.
► Clean the Brewer – to clean the brewer, make a vend as you normally
would, however, instead of inserting a coffee pod into the brewer, you need to
insert a special cleaning tab. The hot water dissolves the cleaning tab, which
in turn cleans all of the areas in which it comes into contact. Make several
vends afterwards (without inserting anything into the brewer) to rinse out the
cleaning solution. Make one final vend using a coffee pod to test the brewer.
► Delime the Water Tank - to minimize servicing time, replace the water tank
with a tank that has already been delimed, then clean the removed tank at the
shop and use it the next time a tank replacement is required.
► Clean the Outlet Valves - to minimize servicing time, replace the outlet
valves with valves that have already been cleaned, then clean the removed
valves at the shop and use them the next time a valve replacement is
required.
► Replace the Water Filter – the water filter should be replaced at least once
a year, or when the water flow rate through the filter has decreased. This is an
indication that the filter is starting to clog.
Every 18 Months
► Replace the hose and grommet in the water tank – the 4" hose and the
grommet that connect to the heat exchange tube inside the water tank, and
the water pump tube elbow on the tank lid, will get harden and brittle over
time and must be replaced.
11
Eccellenza Pod
Equipment Overview
Sanitization – Milk System
Should the Eccellenza Pod’s milk system require sanitization, all of the following
components must be removed and soaked in a sanitizing solution for 30 minutes.
•
•
•
•
•
Drip tray & grill
Spouts
Product hoses
Whipper hose
Whipper components
NOTE: When ready for use, the end-use concentration of all
quaternary chemicals in the solution is not to exceed 200ppm of
active quaternary compound.
To perform a sanitization of the machine components that have an impact on the
milk system, a large leak-proof container, a spray bottle and SC Johnson J-512
sanitizer are required.
1. Fill the leak-proof container with a mixture of water and sanitizer – the
mixture is 2ml of sanitizer per liter of water.
2. Remove the components identified above from the machine.
3. Place them inside the container with the sanitizing solution. Let them soak for
5 minutes.
4. While the components soak, fill a spray bottle with the sanitizing solution (2ml
sanitizer per liter of water).
5. Lightly spray the solution to the exterior of the machine, the interior walls and
interior of the front door, the whipper blade and base, and to the counter-top.
Do not wipe away the solution – let it dry naturally.
6. After their 5 minute soak, remove the components from the leak-proof
container and rinse them with clean warm water.
7. Re-install all of the components back into the machine.
12
Eccellenza Pod
Maintenance
Cleaning the Vacuum Duct (Powder System)
1. Open the front door and remove the two powder dispensers.
2. Lift the front of the upper vacuum duct plate (in the center of the dispenser base),
and pull it towards you to remove it.
3. Remove the steam trap from the whipper system.
4. Lift the front of the lower vacuum duct plate and pull it towards you to remove it.
5. Rinse and thoroughly dry both the upper and lower vacuum duct plates.
To install the vacuum duct plates, follow these same instructions in the reverse
order.
13
Equipment Overview
Removing the Rear Panel
1. Loosen the four screws securing the machine’s rear panel in place.
2. Lift and remove the rear panel.
3. Disconnect the inline wiring connector for the exhaust fan.
14
Eccellenza Pod
Eccellenza Pod
Maintenance
Removing the Top Panel
1. Remove the four screws securing the machine’s top panel in place. There are two
screws on each side of the panel.
2. Lift and remove the top panel.
NOTE: When re-installing the top panel, make certain that the side with the
protective film underneath is installed at the rear left (as illustrated below).
15
Equipment Overview
Eccellenza Pod
Removing the Front Panel
1. Remove the waste bin and open the front door of the machine.
2. Remove the top panel from the machine.
3. Remove the two screws securing the left side of the front panel.
4. Disconnect the wiring connector going to the front panel (this is for the LED wiring).
16
Eccellenza Pod
Maintenance
5. Gently lift the front panel and pull the top of it towards you. This will unhook the
right side of the front panel from the machine wall.
6. Disconnect the three hoses from their respective spouts.



 - Powder Hose
 - Coffee Hose
 - Hot Water Hose
7. Remove the front panel.
17
Eccellenza Pod
Equipment Overview
8. To install the front panel, install notch at the bottom on the panel onto the lower
post on the right wall of the machine.
9. Connect the three product hoses to the three spouts on the bottom of the front
panel.



 - Powder Hose
 - Coffee Hose
 - Hot Water Hose
18
Eccellenza Pod
Maintenance
10. Swing the top of the panel forward and install the notch at the top of the panel
onto the upper post on the right wall of the machine.
11. Secure the left side of the front panel to the machine using two screws.
12. Connect the front panel wiring.
13. Install the top panel and the waste bin.
19
Eccellenza Pod
Equipment Overview
Draining the Water Tank
1. Remove the back panel and the top panel from the machine.
2. Remove the drain hose (and valve) from its clip.
3. With the drain valve closed, remove the black drain plug from the drain valve.
Closed
Open
4. Place the drain hose valve into a leak-proof container and open the valve to drain the
water tank.
5. Once the tank has drained, close the drain valve and re-install the drain plug onto
the valve.
6. Install the drain hose onto its clip, and re-install the back panel and top panel.
20
Eccellenza Pod
Replacing Components
Replacing Components
Brewer
1. Remove the waste bin and open the front door of the machine.
2. Remove the top panel and remove the front panel.
3. Disconnect the inline connector on the wiring harness.
4. Disconnect the brewer outlet hose
a. Remove the safety clip.
b. Push in the collar on the quick-connect fitting and pull out the elbow.
21
Replacing Components
Eccellenza Pod
5. Remove the two wing nuts securing the brewer to the machine.
6. Lift and remove the brewer assembly from the machine.
To install the brewer back into the machine, follow these same instructions in the
reverse order.
WARNING: When reconnecting the outlet elbow to the brewer,
you must install the safety clip under the collar of the fitting to
secure the elbow in place.
22
Eccellenza Pod
Replacing Components
Powder Dispensers
1. With the machine front door open, rotate the spout caps to block each of the powder
dispenser spouts.
2. Rotate the spout caps to block each of the powder dispenser spouts.
3. Remove the powder dispenser by sliding them out towards you.
23
Replacing Components
Eccellenza Pod
4. Fill the replacement dispensers with their respective powders. Never pack the
powders into the dispensers as this causes inconsistent gram throws, and in
some cases, can cause a dispenser to jam.
5. When installing the powder dispensers, they must be properly engaged with the
coupling on the motor (A) and the detection switch (B). If this is not done correctly,
the machine displays a message asking you to install the powder 1 and/or the
powder 2 dispenser(s).
6. Once installed, rotate the spout caps to unblock each of the dispenser spouts.
NOTE: To reduce the risk of powder ‘bearding’ or clogging of the
dispenser spouts, make sure the spouts are completely turned down
(as illustrated above). A retainer on the upper vacuum duct plate will
stop the spouts when they are in their proper position.
7. When the machine is put back into service, a powder rinse cycle will be required to
flush any powder that may have fallen into the whipper bowl.
24
Eccellenza Pod
Replacing Components
Powder Dispenser Motors
1. Drain the water tank as you will need to move it during this process.
2. Remove the top panel, the rear panel and the two powder dispensers.
3. Remove the whipper support plate (four screws) to access the motor wiring.
4. Disconnect the inline wiring connector for the motor that is to be replaced. The blue
wires are for the powder 1 motor and the red for the powder 2 motor.
25
Replacing Components
Eccellenza Pod
5. Remove the screws securing the motor that is to be replaced (there are two screws
per motor).
6. Locate the dispenser motors on the other side of the metal wall shown above. They
are between the tank and the wall.
26
Eccellenza Pod
Replacing Components
7. Carefully lift and slightly pull the empty water tank away from the wall on which the
motors are installed. Do not force it away from the wall.
8. To remove the Powder 2 motor, pull it towards the water tank and turn it slightly so
that both the coupling and the coil of the motor clear the wall.
27
Replacing Components
Eccellenza Pod
9. To remove the Powder 1 motor, pull it towards you and twist it slightly clockwise. It
may be necessary to turn it into the hot water hose to get the motor coupling and
coil to clear the wall.
10. To install the new motors, follow this procedure in the reverse order.
11. After the new motors are mounted onto the wall, reseat the water tank back into its
proper position.
12. Inspect the hoses on the two outlet valves to make certain they are properly
secured to the valves.
13. Inspect the outlet end of the hot water and powder hoses to make certain they are
properly secured to their respective component.
14. When reconnecting the inline power wiring connectors to their motors, make certain
the blue wires are on the powder 1 motor and the red on the powder 2 motor.
15. Test the machine to make certain everything is functioning properly.
28
Eccellenza Pod
Replacing Components
Power Supply
1. Switch off the machine power and disconnect the service cord from the wall outlet.
2. Remove the waste bin and remove the rear panel.
3. The three screws that secure the power supply in place are located on left wall on
the waste bin area. These screws require a smaller tipped Philips screwdriver than
the one typically used for the other screws in the machine.
4. Slightly loosen the three screws securing the power supply to the wall. Do not
remove these screws.
5. From the rear of the machine, lift up the power supply and pull it away from the wall on
which it is mounted. Once cleared from the wall, pull the power supply towards you.
6. Disconnect the two wiring harnesses from the power supply.
29
Replacing Components
Eccellenza Pod
7. Connect the two wiring harnesses to the new power supply (see image above).
8. Install the three mounting screws to the rear of the power supply (if missing).
9. Install the power supply onto the keyhole slots on the inner wall of the machine.
10. Drop the three screws into the keyhole slots and then tighten the screws.
11. Install the rear panel and the waste bin.
12. Connect the service cord to the wall outlet and switch the machine power on.
13. Test the machine to make certain everything is functioning properly.
30
Eccellenza Pod
Replacing Components
Control Board
1. Switch off the machine power and disconnect the service cord from the wall outlet.
2. Remove the rear service panel.
3. The control board is located on the inside of the right wall. Remove the screw that
secures the control board in place.
4. Move the board to the left until it clears the metal edge and pull it towards you.
31
Replacing Components
Eccellenza Pod
5. As you are removing the board, disconnect the wiring from their respective
connectors on the board.
6. The new board can now be installed. As you are installing the new board, connect
the wiring to their respective connectors on the board (see next page for layout of
the board connectors).
NOTE: The wiring connectors are matched with their respective
connectors on the board assembly, reducing the likelihood of making
connection errors. Make certain to push the wiring connectors firmly
into the board connectors, ensuring that they are locked in place.
7. To secure the board in place, lock the rear of the board bracket into the slot on the
metal shelf. Once done, secure the front of the board bracket with a screw.
8. Install the rear panel, connect the service cord to the wall outlet and power up the
machine.
9. Test the machine to make certain everything is functioning properly.
32
Eccellenza Pod
Replacing Components
Connector Layout on the Control Board
LCD Screen
Waste bin detection switch
Water tank (low power)
LED’s for beverage area and brewer pod illumination
MDB – coin changer system
Power supply
Main power wire – black
Power supply
Water pump (coffee)
Powder motors
Brewer
Powder 2 hopper detection switch (yellow marking on
wiring)
Powder 1 hopper detection switch (red marking on wiring)
Firmware update connector (for loading new firmware)
Inset shows older style connector.
33
Eccellenza Pod
Replacing Components
Selection Board or LCD Display
1. Switch off the machine power and disconnect the service cord from the wall outlet.
2. Remove the top panel and open the front door and remove the screws that secure
the selection board cover to the door.
NOTE: The two upper screws are
each equipped with a small plastic
spacer. This spacer also holds the
screws in place to simplify the reinstallation of the board cover. Do
not lose these two spacers!
3. Disconnect the wiring from the selection board.
a. If you are replacing the LCD display, remove the two screws that secure the
LCD to the door and replace the LCD. If replacing the selection board, proceed
to the next step.
34
Eccellenza Pod
Replacing Components
4. To remove the selection panel, the front door must now be removed. Turn the door
until it is almost closed, and then lift it to remove it from the two door hinges.
5. Lay the door on a flat surface. The selection board is secured to the front door with a
double-sided adhesive, therefore it must be pried off. Using a flat head screwdriver,
insert the tip between the selection board and the door, and carefully and slowly
pry the board off the door.
6. After the board is removed, place the board on your table with the adhesive side up.
After you remove the backing from the adhesive on the new selection board,
install the backing onto the adhesive of the old selection board. This prevents
the board from sticking to the packaging should it need to be returned to VKI
under warranty or for repair.
35
Replacing Components
Eccellenza Pod
7. Peel off the backing from the adhesive on the new selection board and install the
backing onto the old selection board.
8. The inside of the front door is equipped with four small alignment tabs (one for each
corner of the board). Lightly place the selection board onto these four alignment
tabs. Once satisfied that it is in the proper position, apply light pressure with your
fingers to the back of the board to make it stick to the door. Avoid touching any of
the IC chips when applying the pressure.
9. Connect the wiring from the LCD to the selection board.
36
Eccellenza Pod
Replacing Components
10. Re-install the front door onto the machine by sliding it down onto the hinges.
11. Connect the wiring from the machine onto the front selection board.
NOTE: This particular connector is square (2 rows x 2 columns) and must be
installed correctly. Pin one on the connector is identified with a small arrow
and this arrow must be pointing to the top left pin on the board connector.
12. Switch the machine power ON, and check the contrast on the LCD screen. If the
contrast needs to be adjusted, it can be done using the potentiometer next to the
LCD connector on the selection board. Once set, switch the machine power OFF.
37
Replacing Components
Eccellenza Pod
13. Make sure the two spacers are installed on the two top screws on the metal
selection board cover. Do not install the board cover if these spacers missing!
14. Install the selection board cover onto the selection board and secure it in place with
four screws – including the spacers on the two top screws.
15. Close the front door, reconnect the service cord to the wall outlet and power up the
machine.
16. Test the machine to make certain everything is functioning properly.
38
Eccellenza Pod
Replacing Components
Water Tank
1. Switch the machine power off and unplug the service cord.
2. Turn off the water supply, and drain the water tank.
3. Remove the machine top panel and the rear panel.
4. Disconnect the wiring to the three water level probes, remove the temperature
probe, and disconnect the water pump tube from the barbed elbow on top of the
water tank.
5. Disconnect the valve wiring and the valve outlet hoses. Be careful that the hoses do
not fall through their cutouts in the center wall.
39
Replacing Components
Eccellenza Pod
6. Open the clamps and remove the inlet hose and the drain hose.
7. Lift the water tank up and out of the machine.
8. To install the replacement water tank, lower the tank onto its front and rear
supports. Make certain that the tab on the bottom of the water tank is locked into
the slot in the metal shelf.
9. Connect the inlet hose and the drain hose to the bottom of the water tank and
secure them with plastic clamps.
10. Connect the outlet hoses onto the outlet valves.
40
Eccellenza Pod
Replacing Components
11. Connect the wiring onto the outlet valves
a) White pair ► Powder Valve
b) Yellow pair ► Hot Water Valve
12. Connect the wiring to the three water level probes, install the temperature probe,
and connect the water pump tube to the barbed elbow on top of the water tank.
13. Turn on the water supply, connect the service cord to the wall outlet and switch on
the machine power.
14. Allow the water tank to fill and check for leaks.
15. Test the machine to make certain everything is functioning properly.
16. Install the rear panel and the top panel.
41
Replacing Components
Eccellenza Pod
Outlet Valve Manifold
1. Switch the machine power off and unplug the service cord.
2. Turn off the water supply, and drain the water tank.
3. Remove the rear panel and the top panel.
NOTE: The Eccellenza Pod machine is equipped with a dual outlet valve
manifold (two stacked outlet valves in one assembly - one for the powder
and one for hot water).
4. Disconnect the valve wiring and the valve outlet hoses. Be careful that the hoses do
not fall through their cutouts in the center wall.
5. Lift the water tank and pull the outlet valve manifold from the valve port on the
water tank. The tank must be lifted high enough so that the valve clears the side
wall. Use caution as there may still be a bit water remaining behind the valve
when you remove it – this water may be extremely hot.
42
Eccellenza Pod
Replacing Components
6. Install the new valve manifold onto the valve port of the water tank. Make certain
the two O-rings are installed on the valve inlet and that the valve is pushed
into the valve port as far as it can go.
7. Lower the water tank back onto its front and rear supports.
8. Connect the outlet hoses onto the outlet valves.
9. Connect the wiring onto the outlet valves
a) White pair ► Powder Valve
b) Yellow pair ► Hot Water Valve
10. Turn on the water supply, connect the service cord to the wall outlet and switch on
the machine power.
11. Allow the water tank to fill and check for leaks.
12. Test the machine to make certain everything is functioning properly.
13. Install the rear panel and the top panel.
43
Replacing Components
Eccellenza Pod
Disassembling the Dual Valve Manifold
1. Remove the two black clips (top and bottom center clips) securing the two valves
together, and gently pull the two valves apart.
2. Remove the two clips securing the valve end cap to the valve body and gently
remove the end cap. There are two o-rings located between the valve body and the
end cap, and they must be replaced when re-assembling the valve.
3. Remove the two clips securing the valve inlet to the valve body and gently remove
the inlet. There is an o-ring located between the valve body and the inlet, and it
must be replaced when re-assembling the valve.
44
Eccellenza Pod
Replacing Components
Disassembling an Outlet Valve
Overview of Outlet Valve Components
Breather Tube
O-Ring
Diaphragm
Hex Nut & Washer
Plunger Housing
Coil
Plunger
Valve Body - Outlet
Valve Body - Main
Plunger Spring
Spacer
1. Remove the breather tube from the valve.
2. Rotate the outlet section of the valve body counterclockwise to release it from the
main valve body, and pull the two sections apart. Be careful not to lose the small
orange o-ring located between the two valve body sections.
3. Remove the hex nut from the coil, and remove the coil from the main valve body. Be
careful not to lose the small black spacer located between the coil and main
valve body.
45
Replacing Components
Eccellenza Pod
4. On the main valve body, twist the ground tab clockwise to free the plunger housing, and
pull it away from the main valve body. This exposes the plunger and assembly. Be
careful not to lose the small spring inserted into the end of the plunger.
5. Pull the plunger assembly out of the main valve body. This exposes the diaphragm
installed onto the tip of the plunger.
6. Remove the diaphragm by pulling it off of the tip of the plunger. The spring on the other
end of the plunger can also be removed.
To re-assemble the outlet valve, follow these same instructions, but in the reverse
order.
46
Eccellenza Pod
Replacing Components
Inlet Valve
1. Switch the machine power off and unplug the service cord from the wall
outlet.
2. Disconnect the water supply and remove the inlet fitting from the inlet
valve.
3. Remove the rear panel from the machine and drain the water tank.
4. Remove the circle clamp and remove the inlet valve’s outlet hose.
5. Disconnect the power wires from both of the inlet valve solenoids.
6. Compress the clip on the right side of the inlet valve, and push the right side of the
valve through the opening in the metal and remove the valve.
47
Replacing Components
Eccellenza Pod
7. To install the new valve, lock the valve’s left side clip to the left of the opening in the
metal, and then push the right side of the valve until the right side clip locks in
place.
8. Secure the valve outlet hose to the new inlet valve with a new Oetiker clamp.
9. Connect the power wires to the valve solenoids.
10. Attach an inlet fitting to the valve and connect the water supply.
11. Connect the service cord to a wall outlet and switch the machine power on – the
water tank will start filling.
12. Check for leaks and, if any are present, repair them immediately.
13. Test the machine to make certain everything is functioning properly.
14. Install the rear panel onto the machine.
48
Eccellenza Pod
Replacing Components
Air Pump
1. Remove the top and rear panels.
2. The air pump is located on the left of the wall behind the brewer (the water pump is
also located in this area, on the right side).
3. Cut the tie-wrap securing the air pump to the wall and disconnect the power wires
and the outlet hose from the pump.
4. Connect the power wires to the new air pump. Note that this is a DC powdered
pump and the wires must be placed on the correct terminals. Connect the
white wire (positive) to the terminal with the ‘+’ marking, and connect the black wire
(ground) to the other terminal.
-
+
49
Replacing Components
Eccellenza Pod
5. Secure the air pump to the opening on the metal wall using a large tie-wrap.
6. Connect the outlet hose to the air pump.
7. Test the machine to make certain everything is functioning properly.
Replacing the Inline Check Valve
The air pump is equipped with a check valve that prevents water from flowing into the
pump, but still allows air to flow out of the pump. To replace this check valve;
1. Cut the two tie-wraps on the check valve and pull the hose off each side. The
check valve has now been removed.
NOTE: The check valve must be installed in the proper direction or you risk
damaging it and/or other components in the equipment.
2. Connect the pump side tubing to the flat side of the check valve.
3. Connect the other tube to the tapered side of the check valve.
4. Secure the tubing with a tie-wrap on each side of the check valve.
50
Eccellenza Pod
Replacing Components
Water Pump
1. Remove the top and rear panels.
2. Disconnect the water pump inlet hose from the fitting on top of the water tank.
3. Disconnect the water pump outlet hose from the inlet of the “Y” fitting (on the
brewer side of the wall).
4. Disconnect the two power wires from the water pump.
5. Remove the four screws securing the water pump to the wall, and remove the pump.
51
Eccellenza Pod
Replacing Components
6. Place the new water pump on the wall and secure it in place with four screws.
7. Connect the power wires to the water pump. Note that this is a DC powdered
pump and the wires must be placed on the correct terminals. Connect the red
wire (positive) to the terminal with the red marking, and connect the blue wire
(ground) to the other terminal.
+
8. Connect the water pump outlet hose to the inlet of the “Y” fitting (on the brewer side
of the wall.
9. Connect the water pump inlet hose to the fitting on top of the water tank.
10. Test the machine to make certain everything is functioning properly.
11. Install the top panel and the rear panel onto the machine.
52
Eccellenza Pod
Replacing Components
Powder Dispenser and Waste Bin Detection Switches
Three detection switches are used in this machine – one to detect the presence of the
waste bin, and the other two to detect the presence of the powder dispensers.
Should you need to replace any one of these detection switches:
1. Remove the waste bin, the two powder dispensers, the top panel and the rear panel.
2. Disconnect the wiring connector at the rear of the switch that is to be replaced.
3. Compress the clip at the front of the switch to unlock it and remove the switch.
4. Press the new switch into the cutout in the metal until the clip locks it in place.
5. Connect the wiring connector to the rear of the switch.
6. Re-install all of the panels, the powder dispensers and the waste bin and test the
machine to make certain everything is functioning properly.
53
Replacing Components
Eccellenza Pod
Whipper Motor
NOTE: Replace the impeller if it has been removed and re-installed multiple
times as it may become loose on the whipper shaft and fall off during
operation.
1. With the power to the machine switched off, remove the waste bin and open the
front door.
2. Rotate the spout caps to block each of the powder hopper spouts.
54
Eccellenza Pod
Replacing Components
3. Disconnect the outlet hose from the whipper chamber.
4. Remove the four screws securing the whipper plate to the machine and remove it.
5. Disconnect the inline power connector from the whipper motor.
6. Remove the steam trap (vacuum cap) from the whipper chamber.
55
Replacing Components
Eccellenza Pod
7. Turn the small handle on the locking ring (on the whipper base) to the right until it
stops. This unlocks the whipper chamber from the whipper base, allowing it to be
pulled off.
8. Remove the screw securing the top of the whipper base to the machine wall, and
turn the handle on the locking ring to the left until it stops.
56
Eccellenza Pod
Replacing Components
9. While pressing down on the locking clip at the front of the plate, press down on the
clip at the rear of the plate, and push it out through to the front.
10. Remove the base, gasket and impeller from the old motor and transfer it to the new
motor.
11. Install the new motor into the cutout in the whipper mounting plate. Install the
bottom of the assembly first, and then push the top of the assembly into the cutout
until the plastic clip locks it in place.
12. Turn the handle on the locking ring completely to the right and secure the base to
the wall with a screw.
57
Replacing Components
Eccellenza Pod
13. Insert the whipper chamber into the base (making sure to also insert the chamber’s
inlet into the adaptor), and turn the handle on the locking ring to the center position
to secure the chamber.
14. Install the steam trap (vacuum cap) onto the whipper chamber.
15. Connect the inline wiring connector that supplies power to the whipper motor.
16. Install the whipper support plate onto the machine and secure it with four screws.
17. Connect the whipper outlet hose, and rotate the spout caps to open each of the
powder hopper spouts.
18. Close the front door and install the waste bin.
19. Power on the machine. A rinse cycle is now required.
20. Perform a “Powder Rinse” cycle to flush any powder that may have fallen into the
whipper chamber.
58
Eccellenza Pod
Replacing Components
Whipper Vacuum Fan
1. Switch off the machine power and disconnect the service cord from the wall outlet.
2. Remove the waste bin.
3. Disconnect the outlet hose from the whipper chamber.
4. Remove the four screws securing the whipper plate to the machine and remove it.
5. Disconnect the two power wires and the vacuum hose from the vacuum fan.
59
Replacing Components
Eccellenza Pod
6. In the waste bin area, loosen the two screws securing the fan to the wall. It is not
necessary to remove these screws.
7. Lift the fan and pull it to the left to remove it.
8. Install the new whipper vacuum fan and tighten the two screws to secure it to the
wall.
9. Connect the two power wires and the vacuum hose to the fan.
10. Re-install the whipper plate and secure it with the four screws.
11. Test the machine to make certain everything is functioning properly.
60
Eccellenza Pod
Replacing Components
Exhaust Fan
1. With the power to the machine switched off, remove the machine’s rear panel.
2. Disconnect the inline wiring connector for the exhaust fan
3. The fan is secured to the rear panel with four screws and hex nuts. Remove the four
exterior screws using a screwdriver, while holding their respective interior hex nuts
with a nut driver or small wrench.
To install the new exhaust fan, follow these same instructions in the reverse
order.
61
Replacing Components
Eccellenza Pod
Main Power Components
The service cord must be disconnected from the wall outlet
when servicing these components. They remain live even when
the main power is switched off at the rear of the machine.
The main power components are all secured to the bottom rear of the machine. Removing
the rear panel provides access to the fuse holder, the main power switch and the service
cord.
1. Switch the machine power off and disconnect the service cord from the wall
outlet.
2. Remove the rear panel of the machine.
3. The main power components are located at the bottom rear of the machine.
4. Replace the faulty component (see next two pages for detailed instructions on
replacing each of these components).
62
Eccellenza Pod
Replacing Components
Fuse Holder (15 Amp)
a. Disconnect the wiring from the fuse holder.
b. Loosen the plastic hex nut that secures the fuse holder to the
machine (see image).
c. Remove the fuse holder and replace it with the new one.
d. Transfer the fuse and the cap from the old fuse holder onto
the new one (if required).
e. Install the new fuse holder and secure it to the machine with
the hex nut.
f. Connect the wiring to the new fuse holder.
Service Cord
a. Disconnect the service cord wiring from the main power switch (switch tabs 1a
and 2a).
b. Disconnect the ground terminal from the grounding post on the metal wall.
c. Compress the strain relief and pull the service cord out of the opening in the
metal.
d. Install the strain relief onto the service cord and insert the end of the new
service cord through the opening in the metal.
e. Connect the service cord wiring to the main power switch (switch tabs 1a and 2a).
f. Connect the ground terminal to the grounding post on the metal wall.
g. Compress the strain relief and pull the service cord into of the opening in the
metal.
63
Replacing Components
Eccellenza Pod
Main Power Switch
a. Disconnect the wiring from the main power switch.
b. Compress the clips on the top of the switch, and push the switch through the
opening in the metal.
c. Insert the new switch into the opening on the metal, and snap it in place to
secure it.
d. Connect the wiring to the new power switch.
i. Black wire (hot) -> connects to tab #1a on the switch
ii. Black wires (hot) - dual terminal -> connects to tab #1 on the switch
iii. White wires (neutral) -> connect to tabs #2 and #2a on the switch.
64
Eccellenza Pod
Installing a Coin Changer System
Installing the Coin Changer System
The Eccellenza Pod uses the “MDB–Level 3” protocol to communicate with a compatible
coin changer. VKI has thoroughly tested and validated ONLY the following coin changer for
proper operation with the Eccellenza Pod (firmware 2.2 or higher):
Coinco® - Guardian 6000 Series, Quantum Pro, CoinPro3
MEI® - Cashflow 7000 Series
NRI® - Currenza C2
Conlux® - MCM5-1
It is highly recommended that you acquire the “Operation & Service” manuals for each
of these changers from their manufacturer. This sophisticated changer is highly
customizable and may require direct configuration through its own respective software,
which is totally independent of the Eccellenza Pod software configuration.
1. Remove the two right side top panel screws, and remove the rear panel.
2. Disconnect and remove the exhaust fan from the original rear panel and install it
onto the rear panel that accompanied the coin changer housing.
65
Installing a Coin Changer System
Eccellenza Pod
3. Install the coin changer housing onto the right side of the machine and secure it by
re-installing the two screws you removed from the top panel through the changer
housing, the top panel and into the machine cabinet. For this operation, you will
require a smaller stubby Philips screwdriver.
4. Connect one end of the supplied wiring extension to the MDB connector on the
control board, and connect the other end to the wiring harness in the changer
housing.
66
Eccellenza Pod
Installing a Coin Changer System
5. Install the new rear panel to the back of both the machine and the coin changer
housing.
a. Make sure the cutout in the rear panel is installed over the wiring harness so
as not to pinch the wiring between the cover and the machine chassis (the
wiring should be sticking out of the cutout). Install the cover plate over the
cutout to cover the wiring harness.
b. Reconnect the exhaust fan wiring.
c. Secure the rear panel onto the machine chassis using the screws provided.
67
Installing a Coin Changer System
Eccellenza Pod
Install the Coin Changer Assembly
1. Unlock the coin changer housing and pull the door open.
2. Loosen the three mounting screws on the inner wall of the housing.
3. Slide the coin changer over the three screws (there are three keyhole slots at the
rear of the changer) and push down on it, making sure all three screws are inserted
into the slot.
68
Eccellenza Pod
Installing a Coin Changer System
4. Flip open the acceptor portion of the coin changer and tighten the three screws to
secure the changer to the housing, and then close the acceptor portion.
5. Connect the coin changer wiring to the small connector in the changer housing.
6. Close and lock the door of the coin changer housing.
Test the Machine and the Coin Changer System
1. To switch the machine from free mode to coin mode, enter the Set-Up mode and
scroll to the Options menu and then select the Vending sub-menu and the
Changer option. Change this setting to “On” to enable coin mode.
2. Insert several coins to test the coin changer system (insert more than the selling
price of the beverage). The coins should be accepted and a credit will be displayed
on the LCD screen.
3. Make a beverage selection and press the Start button to prepare the beverage. You
should receive change if your credit exceeded the selling price of the beverage.
4. Insert a few more coins, only this time, press the coin reject button on the changer.
The money inserted should now be returned to you in the coin return cup.
69
Error Messages
Eccellenza Pod
Updating Equipment Firmware
To update the firmware in the Eccellenza Pod machine, a Load-n-Go handheld programmer
(shown below) is required. Should multiple different firmware files become available for the
Eccellenza Pod, you can load up to four of them onto this one programmer.
NOTE: VKI Technologies does not sell this programmer. It can be purchased
online at www.ccsinfo.com. Please visit this web site for more details.
Software Installation
1. Insert the CD Rom provided into your computer drive.
2. Click on the ccsload folder and select setuccsload.exe.
3. Allow the installation process to complete.
4. Click on the USB-Drivers folder (on CD-Rom).
5. Select usbdrivers.exe and follow the instructions for installing the driver and adding
the new hardware.
6. See the included Help File on the CD (CCSLoad.CHM) for more assistance after
installation.
Hardware Installation
1. Insert four AA batteries into the battery compartment in back of the Load-n-Go
programmer.
2. Connect the Load-n-Go programmer to your PC via the USB cable provided.
3. Run the ccsload.exe software that was installed on your PC (a shortcut should have
been left on your desktop).
70
Eccellenza Pod
Error Messages
Loading Programs onto the Load-n-Go Programmer
1. Connect the Load-n-Go programmer to your PC via the USB cable provided.
2. Run the ccsload.exe software that was installed on your PC to open the CSS
Programmer Control Panel.
3. Once loaded, from the upper right area of the screen, select any of the four memory
banks.
71
Error Messages
Eccellenza Pod
4. Click on the Browse button and select the file from the Open dialog box (your PC)
to be loaded into the programmer, and press the Open button. This step loads the
file into the CSS Programmer Control Panel application.
5. Click on the Test button. A drop-down box opens with a list of compatible memory
chips. From this list, you must select the PIC24FJ128GA006 memory chip.
You must select the PIC24FJ128GA006 memory chip from the list
displayed! If the proper chip is not selected, it will not be possible to
update the machine’s firmware.
72
Eccellenza Pod
Error Messages
6. Click on the “Write to Mem” button to write the specified file to the memory
location that was selected.
7. The file will then be written to the programmer. A progress bar at the bottom of the
window allows you to see how much of the file has been transferred.
NOTE: Do not disconnect the programmer from the PC while the
file is being written.
73
Error Messages
Eccellenza Pod
8. After the file is written to the programmer, a confirmation message appears on the
screen. If any errors prevented the file from being written, they will be displayed in
this area. Also notice that at the lower right of the screen, it reads “Pass=1” – this
indicates that one file has successfully passed the writing process.
9. If you are finished loading files into the programmer, we recommend that you close
the CCS Programmer Control Software application on your PC first, and only then
disconnect the USB cable from your PC.
Loading New Firmware into the Eccellenza Pod
1. Switch off the power to the machine.
2. Remove the rear panel from the machine.
3. Locate the firmware update port in the center of the control board. Newer machines
are equipped with an RJ25 connector (left image) and older machines use a special
port on the control board (right image).
74
Eccellenza Pod
Error Messages
4. On older machines, connect the special programming cable to the firmware update
port in the center of the control board. Note that this connector must be installed in
a specific way (illustrated below). On newer units, connect the phone type cable
directly to the RJ25 connector on the control board.
The three larger silver colored guide pins must align with the three contacts on the
control board, and the four plastic clips on the connector must align with the four
small holes in the control board. Once aligned, compress the sides of the connector
slightly and push the connector onto the board until it locks in place.
Newer machines (and control
boards) are equipped with an
RJ25 phone type connector.
75
Eccellenza Pod
Error Messages
5. Connect other end of the cable to the programmer (uses a standard RJ25 telephone
jack).
6. Switch the machine power on.
7. Press the “On/Off” button on the programmer. The green light will be on when the
unit is powered.
8. Use the “Program Select” button to choose the memory bank in which your file was
stored. One of the four LEDs will be illuminated to indicate the memory bank that is
selected.
9. Press the “Load” button to start the firmware upload. The status LED will start
flashing to indicate that the file is uploading.
10. When the upload is complete, the LED will stop flashing and turn green if the upload
was successful or red if the upload failed.
11. If the upload was successful, switch off the power to the machine, disconnect the
programming cable and switch the machine power back on.
12. If the upload failed, verify that you have the correct file on your PC and repeat the
entire loading process (first from the PC to the programmer, and then from the
programmer to the machine).
NOTE: Once a file is loaded into the programmer, it will remain
stored in the programmer until you write another file into that
memory location.
76
Eccellenza Pod
Error Messages
Error Messages
MESSAGE DISPLAYED
CAUSE
Beverage Unavailable
A beverage cannot be
dispensed.
Brewer Error
An error has been detected
with the brewer.
POSSIBLE REMEDIES
• Make sure the waste bin is installed.
• Make sure both of the powder hoppers
are installed.
• Verify the brewer motor wiring.
• The brewer may be jammed. Repair or
replace the brewer.
• Press "START" () to cycle the brewer.
• Reboot the machine (power off and on).
Brewer Home Error.
The brewer is not in the
home or starting position.
• The brewer may be jammed. Repair or
replace the brewer.
• An electrical connection to the brewer
home switch is faulty.
Button(s) Error
An error has been detected
with one of the selection
buttons.
• The front selection panel may need to
be replaced.
Call Key Operator
The cashbox may be full.
• Empty the cashbox and reset the
Cashbox Total Counter
Empty Waste Bin
Waste bin may be full.
Fill Powder 1
Powder 1 dispenser is low
and required refilling.
Fill Powder 2
Powder 2 dispenser is low
and required refilling.
• Reset the “Refill” message for the
Powder 2 dispenser.
Heating Water
Water inside the hot water
tank is heating.
• Normal operating message and does
not indicate an error.
Insert Waste Bin
The waste bin is missing.
• Install the waste bin.
Insert Powder 1
Powder 1 hopper is missing.
• Install the powder 1 hopper.
Insert Powder 2
Powder 2 hopper is missing.
• Install the powder 2 hopper.
Keypad
Not Connected
The keypad is not being
detected.
• Check the wiring to the keypad.
• Empty the contents of the waste bin.
• Reset the “Waste Bin” counter.
• Refill the dispenser for powder 1.
• Reset the “Refill” message for the
Powder 1 dispenser.
• Refill the dispenser for powder 2.
• Empty and dry the overflow/cup tray.
• Verify the water level probe adjustment.
They may be set too high allowing too
much water into the tank.
Overflow Error
A water overflow has been
detected.
• Water level probes may need to be
cleaned.
• Inlet valve may be leaking, constantly
allowing water to enter the tank. Replace
the inlet valve.
• Water in the tank may be boiling. Lower
the water temperature setting.
77
Eccellenza Pod
Error Messages
MESSAGE DISPLAYED
CAUSE
Overheat Error
The water tank is
overheating.
Power Saving Mode –
Press Start to Exit
The machine is in Power
Saving Mode.
POSSIBLE REMEDIES
• Check the temperature settings in the
set-up.
• The temperature probe may need to be
replaced.
• Press "START" () to exit Power Saving
Mode.
• Check the 15 amp fuse.
Tank Not Heating Error
The hot water tank is not
heating.
• Reset the thermal cut-off switch.
• Verify wiring to heater element.
• Check heater element.
Temperature Probe
Error
The temperature probe is
not functioning correctly.
• Replace the temperature probe.
Thermister Shorted
Error
The thermister is not
functioning correctly.
• Replace the thermister.
Thermister Open Error
The thermister is not
functioning correctly.
• Replace the thermister.
• Clean the water level probes.
Water Level Error
The water tank is
overfilling.
• The water temperature may be too high
– lower the temperature.
• Inlet valve may be leaking – replace inlet
valve.
• At this point, the water tank is not full
and this message has to be reset. To reset
it, switch the power off and on.
Water Source Error
Indicates a problem with
the main water supply not
getting to the water tank.
• If the problem persists, check all
components on the water line (water filter,
tubing, fittings, etc.).
• Check inlet valve to make certain it is
functioning properly.
• In the case of a temporary disruption
with the water supply, the coffee maker will
reset itself after every hour.
• The whipper motor may be jammed.
Clean the whipper assembly.
Whipper Error
78
An error has been detected
with the whipper.
• Verify wiring to the whipper assembly.
• The whipper motor assembly may need
to be replaced.
Eccellenza Pod
Service Manual
Wiring Diagram
79
Service Manual
80
Eccellenza Pod