Sapido BRC70x User manual

http://www.sapido.com.tw/
1
User Manual v1.0.0
CE Statement of Conformity
Our product has been tested in typical configuration by Ecom Sertech Corp and was found
to comply with the essential requirement of “Council Directive on the Approximation of the
Laws of the Member States relating to Electromagnetic Compatibility” (89/336/EEC;
92/31/EEC; 93/68/EEC)
http://www.sapido.com.tw/
User Manual v1.0.0
Chapter 1
1.1
Introduction
Hardware Features
 Main Chipset
 Realtek RTL8196E Network Processor
 Flash & RAM
 Flash:4Mbytes Serial Flash
 RAM:32Mbytes SDRAM
 Ethernet Interface
 WAN: 1 x 10/100 Mbps RJ45 with auto MDI/MDIX
 LAN: 4 x 10/100 Mbps RJ45 with auto MDI/MDIX
 Buttons
 Reboot/Reset:Press 1 second is for reboot; press 10 seconds is for
reset to default configuration
 Power Supply
 Power Adapter DC5V / 0.5A
 DC Jack Connect
 BSMI
 LED Indicators
 Power LED x1
 Status LED x1 (Reset Indicator)
 WAN LED x 1
 LAN LED x 4
 Security Certification
 FCC
 CE
 BSMI
http://www.sapido.com.tw/
User Manual v1.0.0
1.2
Product Appearance
LED Indicator Status Description:
LED
Function
Color
Status
Description
Power
System status
Green On
Status
Reset indicator
System is ready to work
Green On
Blinking Reset or firmware upgrade in
(120ms) progress
WAN x 1
WAN port activity Green On
System is ready to work
100Mbps Ethernet is
connected
Blinking 100Mbps Ethernet Tx/Rx
(30ms) activity
Green On
10Mbps Ethernet is
connected
Blinking 10Mbps Ethernet Tx/Rx
(120ms) activity
http://www.sapido.com.tw/
User Manual v1.0.0
LAN x 4
LAN port activity Green On
100Mbps Ethernet is
connected
Blinking 100Mbps Ethernet Tx/Rx
(30ms) activity
Green On
10Mbps Ethernet is
connected
Blinking 10Mbps Ethernet Tx/Rx
(120ms) activity
http://www.sapido.com.tw/
User Manual v1.0.0
Chapter 2
System and Network Setup
The BRC70X is an easy to setup device for various application and environment, especially
for large installs such as hotels, offices space, warehouses, hot-spots and more.
To begin with BRC70X, you must have the following minimum system requirements. If your
system can’t correspond to the following requirements, you might get some unknown
troubles on your system.

Internet Account for XDSL/Cable Modem

One Ethernet (10/100mbps) network interface card.

TCP/IP and at least one web browser software installed (E.g.: Internet Explorer, Firefox,
Safari、Chrome latest version).

Recommended OS: WinXP, Visata or Win7 / Linux.

2.1
Build Network Connection
Administrator can manage the settings for WAN, LAN, NTP, password, User Accounts,
Firewall, etc.
Please confirm the network environment or the purpose before setting this product.
2.2
Connecting BRC70X
Prepare the followings before the connection:

PC or Notebook for setup

Ethernet cable
1.
Make sure you are under “Router Mode”.
2.
Connect BRC70X to xDSL/ Cable modem with the Ethernet cable, WAN to LAN.
3.
Turn on your Computer.
http://www.sapido.com.tw/
User Manual v1.0.0
2.3
Network setup
After the network connection is built, the next step is setup the router with proper network
parameters, so it can work properly in your network environment. Before you connect to the
router and start configuration procedures, your computer must be able to get an IP address
from the router automatically (use dynamic IP address). If it’s set to use static IP address, or
you’re unsure, please follow the below instructions to configure your computer with dynamic
IP address:
If the operating system of your computer is….
Windows 2000
- please go to section 2.3.1
Windows XP
- please go to section 2.3.2
Windows Vista/Win7
- please go to section 2.3.3
2.3.1
Windows 2000
Click “Start” button (it should be located at lower-left corner of your computer), then click
control panel. Double-click Network and Dial-up Connections icon, double click Local Area
Connection, and Local Area Connection Properties window will appear. Select “Internet
Protocol (TCP/IP)”, then click “Properties”.
http://www.sapido.com.tw/
User Manual v1.0.0
1.
Select “Obtain an IP address automatically” and “Obtain DNS server address
automatically”, then click “OK”.
2.3.2
1.
Windows XP
Click “Start” button (it should be located at lower-left corner of your computer), then
click control panel. Double-click Network and Internet Connections icon, click Network
Connections, then double-click Local Area Connection, Local Area Connection Status
window will appear, and then click “Properties”.
http://www.sapido.com.tw/
User Manual v1.0.0
2.
Select “Obtain an IP address automatically” and “Obtain DNS server address
automatically”, then click “OK”.
2.3.3
1.
Windows Vista / Windows 7
Click “Start” button (it should be located at lower-left corner of your computer), then
http://www.sapido.com.tw/
User Manual v1.0.0
click control panel. Click View Network Status and Tasks, and then click Manage Network
Connections. Right-click Local Area Network, then select “Properties”. Local Area
Connection Properties window will appear, select “Internet Protocol Version 4 (TCP /
IPv4)”, and then click “Properties”.
2.
Select “Obtain an IP address automatically” and “Obtain DNS server address
automatically”, then click “OK”.
http://www.sapido.com.tw/
User Manual v1.0.0
2.4
Router IP Address Lookup
After the IP address setup was completed, please clicks “start” → “run” at the bottom-lower
corner of your desktop:
Input “cmd”, and then click “OK”.
Input “ipconfig”, then press “Enter” key. Please check the IP address followed by “Default
Gateway” (In this example, the gateway IP address of router is 192.168.1.1)
http://www.sapido.com.tw/
User Manual v1.0.0
NOTE: If the IP address of Gateway is not displayed, or the address followed by ‘IP Address’ begins with
“169.x.x.x”, please recheck network connection between your computer and router, and / or go to the
beginning of this chapter, to recheck every step of network setup procedure.
2.4.1
Log into Web GUI
After your computer obtained an IP address from router, please start your web browser, and
input the IP address of the router in address bar, and the following message should be
shown. Please click “admin” to login the BRC70X.
Enter the User name and Password in to the blank and then Click Login. The default values
for User Name and Password are admin (all in lowercase letters).
Users can set or change user name and password used for accessing the web management
interface in this section.
http://www.sapido.com.tw/
User Manual v1.0.0
Input User Name and New Password, then input Confirm Password again.
Chapter 3
Internet Connection
This Chapter describes how to setup BRC70X to the internet. The BRC70X is delivered with
the following factory default parameters.
Default IP address: 192.168.1.1
Default IP subnet mask: 255.255.255.0
Web login user name: admin
Web login password: admin
3.1
1.
Using as a broadband router
Open a Web browser, and enter http://192.168.1.1 (Default Gateway) into the blank.
http://www.sapido.com.tw/
User Manual v1.0.0
2.
Enter the User name and Password into the blank and then click Login. The default
values for User Name and Password are admin (all in lowercase letters).
Status page
Download
pdadd
Logout
3.2
Home button menu
Click Home button icon to enter MENU as below.
http://www.sapido.com.tw/
User Manual v1.0.0
Item
Description
Internet Setup
There are several different method to access
Internet,ADSL 、DHCP、static IP、PPTP、L2TP
Status
You could check WAN, LAN, Client network in status.
Parental control
You can use URL filter and MAC address filter schedule to limit
access Internet.
Firmware Upgrade
This function allows you upgrade the BRC70X firmware to new
version. Please note do not power off the device during the upload
because it may crash the system.
QoS
The QoS can let you classify Internet application traffic by
source/destination IP address and port number.
DoS
Denial of Service
IP Blinding
Static DHCP Setup
VPN Server
PPTP/L2TP general setup introduction.
NAT Management
There are port forwarding and DMZ function
http://www.sapido.com.tw/
User Manual v1.0.0
DDNS
You can assign a fixed host and domain name to a dynamic
Internet IP address. Each time the router boots up, it will reregister its domain-name-to-IP-address mapping with the DDNS
service provider.
Remote management
This page allow you to access the GUI on WAN.
Advance Setup
Advance setting menu
Time Zone
You can maintain the system time by synchronizing with a public
time server over the Internet.
Factory Default
You could reset the current configuration to factory default.
Reboot
This function is used to reboot
logout
This page is used to logout.
http://www.sapido.com.tw/
User Manual v1.0.0
3.3
Internet Setup
Click Internet Setup icon to enter WAN setup as below. The Internet Setup is
depended on the service that you contract with the provider. The BRC70X provides five
selections for the Internet Mode type, PPPoE, DHCP, Static IP , PPTP and L2TP. Check with
your ISP if you don’t know the WAN type.
http://www.sapido.com.tw/
User Manual v1.0.0
3.3.1
PPPoE
Item
Description
User Name
Input your user name provided by your ISP. If you don’t know,
please check with your ISP.
Password
Input the password provided by your ISP.
3.3.2
DHCP
Item
Description
MAC type
Select "Universal” or “Specific"
http://www.sapido.com.tw/
User Manual v1.0.0
3.3.3
Static IP
Item
Description
IP Address
Enter the IP address which is provided by your ISP.
Subnet Mask
Please enter the Subnet Mask address
Gateway
Input ISP Default Gateway Address.
DNS
Input DNS information which is provided by your ISP
3.3.4
PPTP
http://www.sapido.com.tw/
User Manual v1.0.0
Item
Description
Address Mode
Select "Dynamic" or "Static"
IP Address
Input your IP address or domain name
Gateway
Input ISP Default Gateway Address.
Server IP Address
Input your server IP address provided by your ISP. If you don’t
know, please check with your ISP.
User Name
Input PPTP account provided by your ISP.
Password
Input the password provided by your ISP.
Request MPPE Encryption
Microsoft Point-to-Point Encryption (MPPE) provides data security
for the PPTP connection that is between the VPN client and VPN
server.
Enable IGMP Proxy
Enable IGMP Proxy to provide the service for IP hosts and
adjacent multicast routers to establish multicast group
memberships.
3.3.5
L2TP
http://www.sapido.com.tw/
User Manual v1.0.0
Item
Description
Address Mode
Select "Dynamic" or "Static"
IP Address
Input your IP address or domain name
Gateway
Input ISP Default Gateway Address.
Server IP Address
Input your server IP address provided by your ISP. If you don’t
know, please check with your ISP.
User Name
Input PPTP account provided by your ISP.
Password
Input the password provided by your ISP.
MTU Size
Maximum Transmission Unit. Usually provide by computer
operation systems (OS). Advanced users can set it manually.
http://www.sapido.com.tw/
User Manual v1.0.0
Chapter 4
4.1
GUI Function Setup
Status
You could check WAN, LAN, Client network information

WAN information

LAN information
http://www.sapido.com.tw/
User Manual v1.0.0

Client information
Manage client can
access internet or not
4.2
Parental Control
Parental Control provide URL Filtering and MAC Filter Schedule for setup
http://www.sapido.com.tw/
User Manual v1.0.0
4.2.1
URL Filtering
URL Filtering is used to restrict users to access specific websites in internet
Item
Description
Enable URL Filtering
Please select Enable MAC Filtering to filter MAC addresses
URL Address
Please enter the MAC address that needs to be filtered.
Apply
Click on Apply to save the setting data.
Current Filter Table
It will display all ports that are filtering now.
Delete Selected & Delete
All
Click Delete Selected will delete the selected item. Click Delete All
will delete all items in this table.
Notes: This function will not be in effect when the Virtual Server is enabled. Please disable Virtual Server
before activate the URL Filtering function.
http://www.sapido.com.tw/
User Manual v1.0.0
4.2.2
MAC Filter Schedule
When enabled, filtering will be based on the MAC address of LAN computers. Any computer
with its MAC address on this list will be blocked from accessing the Internet.
http://www.sapido.com.tw/
User Manual v1.0.0
Item
Description
Enable MAC Filtering
Please select Enable MAC Filtering to filter MAC addresses.
4.3
Firmware Upgrade
This function can upgrade the firmware of the router. There are two method for user upgrade
firmware: Auto upgrade and Manual upgrade.
Note: The firmware upgrade will not remove your previous settings.
4.3.1
Auto upgrade
http://www.sapido.com.tw/
User Manual v1.0.0
It provide auto detect new firmware from Internet, and user can select to
upgrade new version or not.
4.3.2
Manual upgrade
If you download firmware from website, you can upgrade firmware manual
as below.
4.4
QoS
The QoS can let you classify Internet application traffic by source/destination IP address and
port number.
To assign priority for each type of application and reserve bandwidth can let you have a
better experience in using critical real time services like Internet phone, video conference …
http://www.sapido.com.tw/
User Manual v1.0.0
etc.
Item
Description
Enable QoS
Check “Enable QoS” to enable QoS function for the WAN port. You
also can uncheck “Enable QoS” to disable QoS function for the WAN
port.
Manual Uplink Speed
Set the uplink speed by manual to assign the download or upload
bandwidth by the unit of Kbps.
Manual Downlink Speed
Set the downlink speed by manual to assign the download or upload
bandwidth by the unit of Kbps.
Mode
Select Guaranteed minimum bandwidth or Restricted maximum
bandwidth
MAC Address
Set MAC Address if the address type is by MAC Address
Uplink Bandwidth
Percentage
LAN device bandwidth of uplink bandwidth
Download Bandwidth
Percentage
LAN device bandwidth of download bandwidth
Add
Add the setting data
Delete Selected & Delete
All
Click Delete Selected will delete the selected item. Click Delete All
will delete all items in this table.
http://www.sapido.com.tw/
User Manual v1.0.0
4.5
DoS
Home:
Item
Description
Home
Check “Home” to enable DoS function for prevention. You also can
check “No Prevention” to disable DoS function.
Enterprise:
http://www.sapido.com.tw/
User Manual v1.0.0
Item
Description
Enterprise
Check “Enterprise” to enable DoS function for prevention. You also
can check “No Prevention” to disable DoS function.
4.6
IP Binding
This function allows you reserve IP addresses, and assign the same IP address to the
network device with the specified MAC address any time it requests an IP address. This is
http://www.sapido.com.tw/
User Manual v1.0.0
almost the same as when a device has a static IP address except that the device must still
request an IP address from the DHCP server.
Item
Description
Enable Static DHCP
Select enable to use Static DHCP function
IP Address
Please enter IP address to limit
MAC address
Please enter MAC address to limit
Static DHCP List
It will display all IP and MAC address you made.
Delete Selected & Delete
All
Click Delete Selected will delete the selected item. Click Delete All
will delete all items in this table.
4.7
VPN Server
The VPN Server function providing PPTP/L2TP mode are designed to allow users to an
external network device / computer and office local area network to establish a secure
network connection. And User can safe login office local area network and access to
personal documents, files Sharing and other resources. It provides the most convenient VPN
encryption.
http://www.sapido.com.tw/
User Manual v1.0.0
Item
Description
Enable Setting
Check this option, will start the VPN Server feature.
Connection Type
Provide PPTP or L2TP access connection type.
VPN Server IP
Input the IP address of VPN server
Remote IP range
It is the IP range of assigned to the VPN Client
Authentication Protocol
It is provided three types of authentication protocol
MPPE Encryption Mode
(RC4)
It is provided three encryption modes
User Name
Input the login name of the client user
Password
Input the login password of the client user
Current Filter Table
It will display all ports that are filtering now.
Delete Selected & Delete
All
Click Delete Selected will delete the selected item. Click Delete All
will delete all items in this table.
4.8
NAT Management
http://www.sapido.com.tw/
User Manual v1.0.0
This section contains configurations for the BRC70X ’s advanced functions such as: virtual
server, and DMZ to provide your network under a security environment.
4.8.1
Virtual Server
The Virtual Server feature allows users to create Virtual Servers by re-directing a particular
range of service port numbers (from the WAN port) to a particular LAN IP address.
Item
Description
Enable Virtual Server
Select to enable virtual server or not.
Address
Specify the IP address which receives the incoming packets.
Protocol
Select the protocol type.
http://www.sapido.com.tw/
User Manual v1.0.0
Public Port Range
Enter the port number, for example 80-80.
Private Port Range
Enter the port number, for example 20-22.
Current Port Forwarding
It will display all port forwarding regulation you made.
Table
Delete Selected & Delete
All
Click Delete Selected will delete the selected item. Click Delete All
will delete all items in this table.
Please find the following figure to know that what the virtual server is. The web server is
located on 192.168.1.100, forwarding port is 80, and type is TCP+UDP.
4.8.2
DMZ
The DMZ feature allows one local user to be exposed to the Internet for special-purpose
applications like Internet gaming or videoconferencing. When enabled, this feature opens all
ports to a single station and hence renders that system exposed to intrusion from outside.
The port forwarding feature is more secure because it only opens the ports required by that
application.
http://www.sapido.com.tw/
User Manual v1.0.0
Item
Description
Enable DMZ
It will enable the DMZ service if you select it.
DMZ Host IP Address
Please enter the specific IP address for DMZ host.
4.9
DDNS
You can assign a fixed host and domain name to a dynamic Internet IP address. Each time
the router boots up, it will re-register its domain-name-to-IP-address mapping with the DDNS
service provider. This is the way Internet users can access the router through a domain
name instead of its IP address.
Note: make sure that you have registered with a DDNS service provider before enabling this feature.
http://www.sapido.com.tw/
User Manual v1.0.0
Please enter Domain Name, User Name/Email, and Password/Key. After entering, click on
Apply Changes to save the setting, or you may click on Reset to clear all the input data.
Item
Description
Enable/Disable DDNS
Select enable to use DDNS function. Each time your IP address to
WAN is changed, and the information will be updated to DDNS
service provider automatically.
Service Provider
Choose correct Service Provider from drop-down list, here including
DynDNS, TZO, ChangeIP, Eurodns, OVH, NO-IP, ODS, Regfish
embedded in BRC70X.
User Name/Email
User name is used as an identity to login Dynamic-DNS service.
Password/Key
Password is applied to login Dynamic-DNS service.
4.10 Remote Management
This page allow you to access the GUI on WAN.
http://www.sapido.com.tw/
User Manual v1.0.0
Item
Description
HTTP Connection Port
Users can access GUI by this port,default is 80
Enable Web Server Access
on WAN
Allow user access GUI from WAN side
4.11 Time Zone
Users can select time zone and synchronize the local clock on the router.
Item
Description
Time Zone Select
Please select the time zone.
4.12 Factory Default
You could reset the current configuration to factory default.
http://www.sapido.com.tw/
User Manual v1.0.0
4.13 Reboot
This function is used to reboot
4.14 Logout
This page is used to logout
http://www.sapido.com.tw/
User Manual v1.0.0
Chapter 5
5.1
Advance Setup
Internet Mode: Internet Setup
Please refer Internet Setup
5.2
IP Config
5.2.1.1
PPPoE
Item
Description
User Name
Input your user name provided by your ISP. If you don’t know,
please check with your ISP.
Password
Input the password provided by your ISP.
Service Name
Input the service name provided by your ISP.
http://www.sapido.com.tw/
User Manual v1.0.0
Connection Type
Three types for select: Continues, Connect on Demand, and
Manual.
MTU Size
Maximum Transmission Unit. Usually provide by computer
operation systems (OS). Advanced users can set it manually.
DNS
Select Attain DNS Automatically. Or select Set DNS Manually, if
you want to specify the DNS, and enter the DNS provided by your
ISP in DNS 1 2 3.
Clone Mac Address
Some ISPs require MAC address registration. In this case, enter
the MAC address registered to the provider to "Clone MAC
Address"
Save & Apply
Click on Save to save the setting date, the Apply button for
execute current configuration.
5.2.1.2
DHCP
Item
Description
Host Name
You can keep the default as the host name, or input a specific
name if required by your ISP.
MTU Size
Maximum Transmission Unit. Usually provide by computer
operation systems (OS). Advanced users can set it manually.
DNS
Select Attain DNS Automatically. Or select Set DNS Manually, if
you want to specify the DNS, and enter the DNS provided by your
ISP in DNS 1 2 3.
http://www.sapido.com.tw/
User Manual v1.0.0
Clone Mac Address
Some ISPs require MAC address registration. In this case, enter
the MAC address registered to the provider to "Clone MAC
Address"
Save & Apply
Click on Save to save the setting date, the Apply button for
execute current configuration.
5.2.1.3
Static IP
Item
Description
IP Address
Enter the IP address which is provided by your ISP.
Subnet Mask
Please enter the Subnet Mask address
Gateway
Input ISP Default Gateway Address, .
MTU Size
Maximum Transmission Unit. Usually provide by computer
operation systems (OS). Advanced users can set it manually.
DNS
Input DNS information which is provided by your ISP
Clone Mac Address
Some ISPs require MAC address registration. In this case, enter
the MAC address registered to the provider to "Clone MAC
Address"
Save & Apply
Click on Save to save the setting date, the Apply button for
execute current configuration.
http://www.sapido.com.tw/
User Manual v1.0.0
5.2.1.4
PPTP
Item
Description
Server IP Address
Input your server IP address provided by your ISP. If you don’t
know, please check with your ISP.
User Name
Input PPTP account provided by your ISP.
Password
Input the password provided by your ISP.
MTU Size
Maximum Transmission Unit. Usually provide by computer
operation systems (OS). Advanced users can set it manually.
Enable MPPE Encryption
Microsoft Point-to-Point Encryption (MPPE) provides data security
for the PPTP connection that is between the VPN client and VPN
server.
Enable MPPC Compression
Microsoft Point-to-Point Compression (MPPC) is a scheme used to
compress Point-to-Point Protocol (PPP) packets between Cisco
and Microsoft client devices. The MPPC algorithm is designed to
optimize bandwidth utilization in order to support multiple
simultaneous connections. The MPPC algorithm uses a LempelZiv (LZ) based algorithm with a continuous history buffer, called a
http://www.sapido.com.tw/
User Manual v1.0.0
dictionar
DNS
Select Attain DNS Automatically. Or select Set DNS Manually, if
you want to specify the DNS, and enter the DNS provided by your
ISP in DNS 1 2 3.
Clone Mac Address
Some ISPs require MAC address registration. In this case, enter
the MAC address registered to the provider to "Clone MAC
Address"
Save & Apply
Click on Save to save the setting date, the Apply button for
execute current configuration.
5.2.1.5
L2TP
Item
Description
Server IP Address
Input your server IP address or Host Name provided by your ISP.
If you don’t know, please check with your ISP.
User Name
Input PPTP account provided by your ISP.
Password
Input the password provided by your ISP.
MTU Size
Maximum Transmission Unit. Usually provide by computer
operation systems (OS). Advanced users can set it manually.
http://www.sapido.com.tw/
User Manual v1.0.0
DNS
Select Attain DNS Automatically. Or select Set DNS Manually, if
you want to specify the DNS, and enter the DNS provided by your
ISP in DNS 1 2 3.
Clone Mac Address
Some ISPs require MAC address registration. In this case, enter
the MAC address registered to the provider to "Clone MAC
Address"
Save & Apply
Click on Save to save the setting date, the Apply button for
execute current configuration.
5.2.2
LAN
Use this page to set up the local IP address and subnet mask for your router.
Please select LAN Interface Setup under the IP Config menu and follow the
instructions below to enter the LAN setting page to configure the settings you
want.
Item
Description
IP Address
The default value of LAN IP address is 192.168.1.1 for this router.
Subnet Mask
Input Subnet Mask, normally it is 255.255.255.0.
http://www.sapido.com.tw/
User Manual v1.0.0
Default Gateway
Input ISP Default Gateway Address. If you don’t know, please
check with your ISP.
DHCP
Enable or disable DHCP services. The DHCP server will
automatically allocate an unused IP address from the IP address
pool to the requesting computer if enabled.
DHCP Client Range
Define the DHCP client range and then the DHCP server will
assign an IP to the requesting computer from this range. The
Show Client will display every assigned IP address, MAC
address, and expired time. The default range is 192.168.1.100 192.168.1.200.
Device Name
The default is 11N_Broadband_Router。
802.1d Spanning Tree
IEEE 802.1d Spanning Tree Protocol (STP) is a link layer
network protocol that ensures a loop-free topology for any bridged
LAN. The main purpose of STP is to ensure that you do not create
loops when you have redundant paths in your network. Loops are
deadly to a network.
Clone MAC Address
Copy the MAC address from the device you had registered to your
ISP if your ISP asks for the specific MAC Address.
5.2.3
DDNS
You can assign a fixed host and domain name to a dynamic Internet IP address. Each time
the router boots up, it will re-register its domain-name-to-IP-address mapping with the DDNS
service provider. This is the way Internet users can access the router through a domain
name instead of its IP address.
Note: make sure that you have registered with a DDNS service provider before enabling this feature.
http://www.sapido.com.tw/
User Manual v1.0.0
Please enter Domain Name, User Name/Email, and Password/Key. After entering, click on
Apply Changes to save the setting, or you may click on Reset to clear all the input data.
Item
Description
Enable/Disable DDNS
Select enable to use DDNS function. Each time your IP address to
WAN is changed, and the information will be updated to DDNS
service provider automatically.
Service Provider
Choose correct Service Provider from drop-down list, here including
DynDNS, TZO, ChangeIP, Eurodns, OVH, NO-IP, ODS, Regfish
embedded in BRC70X .
User Name/Email
User name is used as an identity to login Dynamic-DNS service.
Password/Key
Password is applied to login Dynamic-DNS service.
Save & Apply
Click on “Save” to save the setting data. The “Apply” button can
execute current configuration
5.3
IPv6 Config
http://www.sapido.com.tw/
User Manual v1.0.0
Item
Description
Origin Type
SLAAC、DHCPv6、IP。Please check ISP to get correct type
WAN Link Type
PPPoE、IP
PPPoE
Use IPv4 PPPoE account and password to do IPv6 connect
Child Prefix Address
Check ISP to get this data
Static IP
Check ISP to get IP address and default gateway IP address
Router Name
Router domain
DNSv6
Select Attain DNS Automatically. Or select Set DNS Manually, if you
want to specify the DNS, and enter the DNS provided by your ISP in
DNS
http://www.sapido.com.tw/
User Manual v1.0.0
5.4
NAT
This section contains configurations for the BRC70X ’s advanced functions such as: virtual
server, and DMZ to provide your network under a security environment.
5.4.1
DMZ
The DMZ feature allows one local user to be exposed to the Internet for special-purpose
applications like Internet gaming or videoconferencing. When enabled, this feature opens all
ports to a single station and hence renders that system exposed to intrusion from outside.
The port forwarding feature is more secure because it only opens the ports required by that
application.
Item
Description
Enable DMZ
It will enable the DMZ service if you select it.
DMZ Host IP Address
Please enter the specific IP address for DMZ host.
5.4.2
Virtual Server
The Virtual Server feature allows users to create Virtual Servers by re-directing a particular
range of service port numbers (from the WAN port) to a particular LAN IP address.
http://www.sapido.com.tw/
User Manual v1.0.0
Item
Description
Enable Virtual Server
Select to enable virtual server or not.
Address
Specify the IP address which receives the incoming packets.
Protocol
Select the protocol type.
Public Port Range
Enter the port number, for example 80-80.
Private Port Range
Enter the port number, for example 20-22.
Current Port Forwarding
It will display all port forwarding regulation you made.
Table
Delete Selected & Delete
All
Click Delete Selected will delete the selected item. Click Delete All
will delete all items in this table.
Please find the following figure to know that what the virtual server is. The web server is
located on 192.168.1.100, forwarding port is 80, and type is TCP+UDP.
http://www.sapido.com.tw/
User Manual v1.0.0
5.5
VPN Server: PPTP/L2TP Setup
Please refer VPN server
5.6
Firewall
5.6.1
DoS
Please refer DoS
5.5.2 QoS
http://www.sapido.com.tw/
User Manual v1.0.0
Item
Description
Enable QoS
Check “Enable QoS” to enable QoS function for the WAN port. You
also can uncheck “Enable QoS” to disable QoS function for the WAN
port.
Automatic uplink speed
Check the Automatic uplink speed.
Manual Uplink speed
Input uplink bandwidth manually
Automatic downlink
speed
Check the Automatic downlink speed.
Manual Downlink speed
Input downlink bandwidth manually
Address Type
Set QoS by IP Address or MAC address
Local IP Address
Set local IP Address if the address type is by IP Address
MAC Address
Set MAC Address if the address type is by MAC Address
http://www.sapido.com.tw/
User Manual v1.0.0
Mode
Select Guaranteed minimum bandwidth or Restricted maximum
bandwidth
Uplink Bandwidth
Key in the bandwidth.
Downlink Bandwidth
Key in the bandwidth.
5.5.3 Port Filtering
When enabled packets are denied access to Internet/filtered based on their port address.
Item
Description
Enable Port Filtering
Select Enable Port Filtering to filter ports.
Port Range
Enter the port number that needs to be filtered.
Protocol
Please select the protocol type of the port.
Add
Click on Add to save the setting data.
Current Filter Table
It will display all ports that are filtering now.
Delete Selected & Delete
All
Click Delete Selected will delete the selected item. Click Delete All
will delete all items in this table.
Port 80 has been blocked as the following illustrate.
http://www.sapido.com.tw/
User Manual v1.0.0
IP: 192.168.1.x
Port: 80-80
5.5.4 IP Filtering
When enabled, LAN clients are blocked / filtered from accessing the Internet based on
their IP addresses
Item
Description
Enable IP Filtering
Please select Enable IP Filtering to filter IP addresses.
Local IP Address
Please enter the IP address that needs to be filtered.
Protocol
Please select the protocol type of the IP address
Apply
Click on Apply to add the setting data
Current Filter Table
It will display all ports that are filtering now.
Delete Selected & Delete
All
Click Delete Selected will delete the selected item. Click Delete All
will delete all items in this table.
http://www.sapido.com.tw/
User Manual v1.0.0
5.5.5 Mac Filter Schedule
Please refer Mac Filter Schedule
5.5.6 URL Filtering
Please refer URL Filtering
5.5.7 IP Binding
Please refer IP Binding
5.5.8 VLAN
5.5.9 VLAN
VLAN Settings
Item
Description
Tag
Add VLAN tag to packet
VID
Set VLAN ID(1~4096)
http://www.sapido.com.tw/
User Manual v1.0.0
Priority
It indicates the frame priority level. Values are from 0 (best effort) to
7 (highest); 1 represents the lowest priority
CIF
Enable or Disable CIF
http://www.sapido.com.tw/
User Manual v1.0.0
5.6 System
This section including Wake on LAN, Change Username/Password, Upgrade Firmware,
Profiles Save,
Remote Management,
Time Zone, UPnP, Route Setup, VPN
Passthrough, and Wan Type Auto Detection. It is easy and helpful for users making more
detailed settings.
5.6.2
Wake on Lan
Switch your computer ON through your LAN or the Internet . To support WOL you must have a
computer with Motherboard that supports WOL, as well as a Network Controller (NIC) supporting
this function. Most of the newer Motherboard (circa 2002 and On), have an On Board NIC that
supports WOL. Otherwise you need to install a PCI NIC that is WOL capable.
5.6.3
Change Password
Users can set or change user name and password used for accessing the web management
interface in this section.
http://www.sapido.com.tw/
User Manual v1.0.0
Input User Name and New Password, then input Confirm Password again.
5.6.4
Firmware Upgrade
Please refer Firmware Upgrade
5.6.5
Profiles Save
Users can create a backup file that contains current router settings. This backup file can be
used to restore router settings. This is especially useful in the event you need to reset the
router to its default settings.
1.
Save Configuration
(1). Click Save
(2). Please click “Save” to save the configuration to your computer.
http://www.sapido.com.tw/
User Manual v1.0.0
(3). Select the location which you want to save file, then click Save.
2.
Load configuration file
(1). Tap “browse” and select configuration file then click Open
http://www.sapido.com.tw/
User Manual v1.0.0
(2). Click Upload to upload configuration file to BRC70X .
(3). After 60 seconds, BRC70X will reboot automatically.
5.6.6
Remote Management
Please refer Remote Management
5.6.7
Time Zone
Users can synchronize the local clock on the router to an available NTP server
(optional). To complete this setting, enable NTP client update and select the correct
Time Zone.
http://www.sapido.com.tw/
User Manual v1.0.0
Item
Description
Time Zone Select
Please select the time zone.
Enable NTP client update
Please select to enable NTP client update or not.
Automatically Adjust
Please select to enable Automatically Adjust Daylight Saving or
not.
Daylight Saving
NTP Server
Please select the NTP server from the pull-down list, or you can
enter the NTP server IP address manually.
Save & Apply
Click on Save to save the setting date, the Apply button for
execute current configuration.
5.6.8
UpnP

UPNP
Universal Plug and Play (UPnP) is a standard of networking protocols
promulgated by the UPnP Forum. The goals of UPnP are to allow devices to
connect seamlessly and to simplify the implementation of networks in the
home (data sharing, communications, and entertainment) and in corporate
http://www.sapido.com.tw/
User Manual v1.0.0
environments for simplified installation of computer components. BRC70X
supports UPnP function, and can cooperate with other UPnP devices. When
you activate UPnP, please click My Network Places. Users will see an Internet
Gateway Device icon. By click the icon, users can enter the GUI of the router.
If you do not wish to use UPnP, you can disable it.
5.6.9
Route Setup
Dynamic routing is a distance-vector routing protocol, which employs the hop count as a
routing metric. RIP prevents routing loops by implementing a limit on the number of hops allowed
in a path from the source to a destination. The maximum number of hops allowed for RIP is 15
Static routing is a data communication concept describing one way of configuring path
selection of routers in computer networks. It is the type of routing characterized by the absence
of communication between routers regarding the current topology of the network.This is achieved
by manually adding routes to the router routing table.
http://www.sapido.com.tw/
User Manual v1.0.0
Item
Description
Enable Dynamic Route
Enable or Disable dynamic route
NAT
Enable or Disable NAT function
Transmit
There are 3 options:
Receive
1.
Disable:do not send any RIP packet out
2.
Send RIP1 packet out
3.
Send RIP2 packet out
There are 3 options:
4.
Disable:do not receive any RIP packet
5.
Only receive RIP1 packet
6.
Only receive RIP2 packet
Item
Description
Enable Static Route
Enable or Disable dynamic route
IP Address
Destination IP address
Subnet Mask
Destination IP subnet mask
Gateway
Gateway IP address for destination
Metric
Metric number on router’s routing table
Interface
Static route rule for LAN or WAN interface
5.6.10 VPN Passthough
Virtual Private Networking (VPN) is typically used for work-related networking. For VPN tunnels,
the router supports IPSec, Pass-through, PPTP Pass-through, and L2TP Pass-through.
http://www.sapido.com.tw/
User Manual v1.0.0
Item
Description
IPSec Pass-through
Internet Protocol Security (IPSec) is a suite of protocols used to
implement secure exchange of packets at the IP layer. To allow
IPSec tunnels to pass through the router, IPSec Pass-through is
enabled by default. To disable IPSec Pass-through , select Disable
PPTP Pass-through
Point-to-Point Tunneling Protocol is the method used to enable
VPN sessions to a Windows NT 4.0 or 2000 server. To allow PPTP
tunnels to pass through the router, PPTP Pass-through is enabled
by default. To disable PPTP Pass-through, select Disable.
L2TP Pass-through
To allow the L2TP network traffic to be forwarded to its destination
without the network address translation tasks.
IPV6 Pass-through
Allow IPV6 packet to be forwarded to its destination without the
network address translation tasks.
5.6.11 Wan Type Auto Detection
http://www.sapido.com.tw/
User Manual v1.0.0
6
Q&A
6.5 Installation
1.
Q: Where is the XDSL Router installed on the network?
A: In a typical environment, the Router is installed between the XDSL line and the LAN.
Plug the XDSL Router into the XDSL line on the wall and Ethernet port on the Hub
(switch or computer).
2.
Q: Why does the throughput seem slow?
A: To achieve maximum throughput, verify that your cable doesn’t exceed 100 meter. If
you have to do so, we advise you to purchase a bridge to place it in the middle of
the route in order to keep the quality of transmitting signal. Out of this condition you
would better test something else.

Verify network traffic does not exceed 37% of bandwidth.

Check to see that the network does not exceed 10 broadcast messages per
second.

Verify network topology and configuration.
6.6 LED
1.
Why doesn’t BRC70X power up?
A: Check if the output voltage is suitable, or check if the power supply is out of order.
2.
The Internet browser still cannot find or connect to BRC70X after verifying the IP
address and LAN cable, the changes cannot be made, or password is lost.
A: In case BRC70X is inaccessible; you can try to restore its factory default settings.
Please press the “Reset” button and keep it pressed for over 7 seconds and the light
of STATUS will vanish. The LEDs will flash again when reset is successful.
3.
Why does BRC70X shut down unexpectedly?
A: Re-plug your power adapter. Then, check the STATUS indicator; if it is off, the
internal flash memory is damaged. For more help, please contact with your provider.
http://www.sapido.com.tw/
User Manual v1.0.0
6.7 IP Address
1.
Q: What is the default IP address of the router for LAN port?
A: The default IP address is 192.168.1.1 with subnet mask 255.255.255.0
2.
Q: I don't know my WAN IP.
A: There are two ways to know.
Way 1:
Check with your Internet Service Provider.
Way 2:
Check the setting screen of BRC70X. Click on Status & Log item to
select Network Configuration on the Main Menu. WAN IP is shown on
the WAN interface.
3.
How can I check whether I have static WAN IP Address?
A: Consult your ISP to confirm the information, or check Network Configuration in
BRC70X ’s Main Menu.
4.
Will the Router allow me to use my own public IPs and Domain, or do I have to
use the IPs provided by the Router?
A: Yes, the Router mode allows for customization of your public IPs and Domain.
6.8 OS Setting
1.
Why can’t my computer work online after connecting to BRC70X?
A: It’s possible that your Internet protocol (TCP/IP) was set to use the following IP
address. Please do as the following steps. (Windows 2000 & XP) Start>Settings>
Network and Dial-up Connections>double click on Internet Protocol(TCP/IP)>
select obtain IP address automatically> Click on OK button. Then, open Internet
browser for testing. If you still can’t go online, please test something else below.

Verify network configuration by ensuring that there are no duplicate IP
addresses.

Power down the device in question and ping the assigned IP address of the
device. Ensure no other device responds to that address.

Check that the cables and connectors or use another LAN cable.
http://www.sapido.com.tw/
User Manual v1.0.0
2.
Q: Why can't I connect to the router's configuration utility?
A: Possible Solution 1: Make sure that your Ethernet connect properly and securely.
Make sure that you've plugged in the power cord.
Possible Solution 2: Make sure that your PC is using an IP address within the range
of 192.168.1.2 to 192.168.1.254. Make sure that the address of the subnet mask is
255.255.255.0. If necessary, the Default Gateway data should be at 192.168.1.1. To
verify these settings, perform the following steps:
Windows 2000, or XP Users:
1.
Click on Windows Start > click on Run > input cmd > click on OK button.
2.
At the DOS prompt, type ipconfig/all.
3.
Check the IP Address, Subnet Mask, Default Gateway data. Is this data
correct? If the data isn't correct. Please input ipconfig/release > press Enter >
input ipconfig/renew > press Enter.
Possible Solution 3: Verify the connection setting of your Web browser and verify
that the HTTP Proxy feature of your Web browser is disabled. Make these
verifications so that your Web browser can read configuration pages inside your
router. Launch your Web browser.
Internet Explorer Users:
1. Click on Tools > Internet Options > Connections tab.
2. Select never dial a connection, click on Apply button, and then click on OK
button.
3. Click on Tools and then click on Internet Options.
4. Click on Connections and then click on LAN Settings.
5. Make sure none of the check boxes are selected and click on OK button.
6. Click on OK button.
Netscape Navigator Users:
1. Click on Edit > Preferences > double-click Advanced in the Category window.
2. Click on Proxies > select Direct connection to the Internet > click on OK
button.
3. Click on Edit again and then click on Preferences.
4. Under category, double-click on Advanced and then click on Proxies.
http://www.sapido.com.tw/
User Manual v1.0.0
5. Select Direct connection to the Internet and click on OK button.
6. Click on OK button.
3.
Q:
Web page hangs, corrupt downloads, or nothing but junk characters is being
displayed on the screen. What do I need to do?
A: Force your NIC to 10Mbps or half duplex mode, and turn off the "Auto-negotiate"
feature of your NIC as a temporary measure. (Please look at the Network Control
Panel, in your Ethernet Adapter's Advanced Properties tab.)
4.
Q: Why can't I connect to the Web Configuration?
A: you can remove the proxy server settings in your web browser.
6.9 BRC70X Setup
1.
Q: Why does BRC70X’s setup page shut down unexpectedly?
A: If one of the pages appears incompletely in BRC70X ’s setup pages, please click on
Logout item on the Main Menu before shutting it down. Don’t keep it working. Then,
close Internet browser and open it again for going back to the previous page.
2.
Q:
I don’t know how to configure DHCP.
A: DHCP is commonly used in the large local network. It allows you to manage and
distribute IP addresses from 2 to 254 throughout your local network via BRC70X.
Without DHCP, you would have to configure each computer separately. It’s very
troublesome. Please Open Internet browser > Input 192.168.1.1 in the website
blank field > Select DHCP Server under the IP Config Menu. For more
information, please refer to 3.3.2 (Router Mode) or 4.3.1 (AP Mode).
3.
Q: How do I upgrade the firmware of BRC70X ?
A: Periodically, a new Flash Code is available for BRC70X on your product supplier’s
website. Ideally, you should update BRC70X’s Flash Code using Firmware
Upgrade on the System Management menu of BRC70X Settings.
4.
Q: Why is that I can ping to outside hosts, but cannot access Internet websites?
A: Check the DNS server settings on your PC. You should get the DNS servers
settings from your ISP. If your PC is running a DHCP client, remove any DNS IP
http://www.sapido.com.tw/
User Manual v1.0.0
address setting. As the router assign the DNS settings to the DHCP-client-enabled
PC.
5.
Q: BRC70X couldn’t save the setting after click on Apply button?
A: BRC70X will start to run after the setting finished applying, but the setting isn’t
written into memory. Here we suggest if you want to make sure the setting would be
written into memory, please reboot the device via Reboot under System
Management directory.
6.10 Support
1.
Q: What is the maximum number of IP addresses that the XDSL Router will
support?
A: The Router will support to 253 IP addresses with NAT mode.
5. Q: Is the Router cross-platform compatible?
A: Any platform that supports Ethernet and TCP/IP is compatible with the Router.
6.11 Others
1.
Q: Why does the router dial out for PPPoE mode very often?
A: Normally some of game, music or anti-virus program will send out packets that
trigger the router to dial out, you can close these programs. Or you can set the idle
time to 0, then control to dial out manually.
2.
Q: What can I do if there is already a DHCP server in LAN?
A: If there are two DHCP servers existing on the same network, it may cause conflict
and generate trouble. In this situation, we suggest to disable DHCP server in router
and configure your PC manually.
http://www.sapido.com.tw/
User Manual v1.0.0
7
Appendices
7.5 Operating Systems
1.
Microsoft:Windows 2000, XP, Vista, Windows 7.
2.
Apple:Mac OS X 10.4.7, Leopard and the following related versions.
3.
Linux:Redhat 9, Fedora 6 & 7, Ubuntu 7.04 and the following related versions.
7.6 Browsers
1.
Internet Explorer ver. 6 and 7 and the following related versions.
2.
FireFox ver. 2.0.0.11 and the following related versions.3.
3.
Safari ver. 3.04 and the following related versions.
7.7 Communications Regulation Information
Should any consumers need to learn more information, services and supports, please
contact the supplier of your product directly.
http://www.sapido.com.tw/
User Manual v1.0.0