SERVICE
MANUAL
REVISION 0
APR. 2000
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
COPYRIGHT © 2000 CANON INC.
Printed in Japan
Imprimè au Japon
Use of this manual should be strictly supervised
to avoid disclosure of confidential information.
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
LIST OF SERIAL NUMBER
FAU-S11
F96-1911
F96-1931
AZH000000BZH000000-
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
CONTENTS
CHAPTER 1 : GENERAL DESCRIPTIONS
I.
FEATURES ................................ 1-1
A. Front View .......................... 1-3
II. SPECIFICATIONS ....................... 1-2
B. Bottom View ....................... 1-3
III. EXTERIOR FEATURES ............... 1-3
CHAPTER 2 : OPERATION AND TIMING
I.
BASIC OPERATION .................... 2-1
B. Electrical System ................ 2-2
A. System Configuration .......... 2-1
C. Inverter PCB ....................... 2-3
CHAPTER 3 : MECHANICAL SYSTEM
I.
PARTS REPLACEMENT .............. 3-1
D. Removing Inverter Cover ... 3-10
A. Removing Top Cover ........... 3-1
E. Attaching the Inverter Cover
......................................... 3-11
B. Removing Hinge .................. 3-2
C. Removing FAU Cable ........... 3-7
CHAPTER 4 : MAINTENANCE AND SERVICING
I.
PERIODICAL REPLACEMENT
III. PERIODICAL SERVICING ........... 4-1
PARTS ....................................... 4-1
IV. SPECIAL TOOLS ........................ 4-1
II. CONSUMABLE PARTS
V.
SOLVENTS AND LUBRICANTS .... 4-1
DURABILITY .............................. 4-1
CHAPTER 5 : TROUBLESHOOTING
I.
POSSIBLE CAUSE AND CORRECTIVE
ACTION ..................................... 5-1
CHAPTER 6 : PARTS CATALOG
FIGURE 100 .............................. 6-2
COPYRIGHT © 2000 CANON INC.
CANON FAU-S11 REV.0 APR 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
APPENDIX
I.
II. INVERTER PCB CIRCUIT DIAGRAM
GENERAL CIRCUIT
DIAGRAM .................................. A-1
COPYRIGHT © 2000 CANON INC.
........................................... A-2
CANON FAU-S11 REV.0 APR 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
CHAPTER 1
GENERAL DESCRIPTIONS
I.
FEATURES ................................ 1-1
A. Front View .......................... 1-3
II. SPECIFICATIONS ....................... 1-2
B. Bottom View ....................... 1-3
III. EXTERIOR FEATURES ............... 1-3
COPYRIGHT © 2000 CANON INC.
CANON FAU S-11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
CHAPTER 1
I. FEATURES
FAU-S11 is a film adapter unit (FAU) used for CanoScan FB1210U to scan films incorporating
the following features.
* Color and monochrome, negative and positive films can be scanned.
* Film guide enables to scan 35mm film, brownie film (max. 120 x 60mm), and 4 x 5 inches
film.
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
1-1
CHAPTER 1
II. SPECIFICATIONS
Film Type
Film Size
Light Source
Brightness
Operating Environment
Power Source
Standard point of scanning area
Dimensions
Weight
Durability
: Color and monochrome, negative and positive
: 35mm sleeve (preview by 3 frames, scan by 1 frame)
35mm slide mount
Brownie (Max. 120 x 60mm)
4 x 5 inches
: Cold cathode fluorescent lamp
: 3200cd/square meters +/-10%
: Temperature : 10 to 35 degrees
Relataive humidity : 20 to 80%RH
: Supplied from CanoScan FB1210U
: X=45mm, Y=35mm
: 285 (width) x 407.5 (depth) x 33 (height) mm
: 920g
: 20,000 times of the FAU's open/close
Specifications are subject to change without prior notice.
1-2
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
CHAPTER 1
III. EXTERIOR FEATURES
1
A. Front View
2
q FAU Cable
w Top Cover
Figure 1-1
B. Bottom View
1
2
3
q Sponge Sheet
w Hinge
e Lamp Cover Assembly
Figure 1-2
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
1-3
CHAPTER 2
OPERATION AND TIMING
I.
BASIC OPERATION .................... 2-1
B. Electrical System ................ 2-2
A. System Configuration .......... 2-1
C. Inverter PCB ....................... 2-3
COPYRIGHT © 2000 CANON INC.
CANON FAU S-11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
CHAPTER 2
I. BASIC OPERATION
A. System Configuration
The film adapter unit FAU-S11 is an optional device for CanoScan FB1210U to provide the
light source for scanning films.
When the appropriate light source projects through a film and the host computer program
controls the scanning unit moving, charge-coupled-device (CCD) collects all the light signals of
the film and synchronically generates the real analog signals. The main PCB then converts the
analog signal into digital signal. Finally, scanner driver transforms the digital signal into an
image and saves it in the host computer.
Film Adapter Unit (FAU-S11)
Inverter PCB
FAU Lamp
Host
Computer
Figure 2-1
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
2-1
CHAPTER 2
B. Electrical System
Electrical control of the FAU is perfromed by the main PCB in the scanner. Inverter PCB
performs various processing in the FAU according to the control signal sent from the main
PCB.
CN2
FAU Lamp
Scanner
(Main PCB)
Inverter PCB
JP2
CN1
CN3
FAU Lamp
Figure 2-2
2-2
COPYRIGHT © 2000 CANON INC. CANON FAU S-11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
CHAPTER 2
C. Inverter PCB
FAU lamp ON depends on the device selection by the host computer. When the scanner is
powered ON, the scanning lamp is turned ON. When FAU is selected by the host computer as
a TWAIN or Plug-in Module compliant input device and application software is started, the FAU
lamp is turned ON and the scanning lamp is turned OFF.
FAU Lamp
Scanner
(Main PCB)
CN2-2
CN2-3
CN3-2
Inverter PCB
CN1-1 JP2-1
-2
-2
-3
-3
FLON
+12V
GND
CN3-3
FAU Lamp
Figure 2-3
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
2-3
CHAPTER 2
An inverter transforms the voltage (+12V) supplied from the scanner into tremendously high
voltages to light on two cold cathode fluorescent lamps to generate the initial light source. The
initial light source is transformed to an equal-intensity light source through Reflective Film,
Light Guide Plate, 1st Diffusive Film, Brightness Enhancement Film (BEF), 2nd Diffusive Film
to Transparent Plate.
Reflective Film
Light Guide Plate
1st Diffusive Film
Brightness Enhancement Film
2nd Diffusive Film
Transparent Plate
Figure 2-4
2-4
COPYRIGHT © 2000 CANON INC. CANON FAU S-11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
CHAPTER 2
High Voltage
Voltage supplied
from the scanner
Transparent
Plate
Inverter
2nd Diffusive
Film
Cold Cathode
Fluorescent Lamp
Light Enhancement Film
1st Diffusive
Film
Reflective Film
Light Guide
Plate
Film
Figure 2-5
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
2-5
CHAPTER 3
MECHANICAL SYSTEM
I.
PARTS REPLACEMENT .............. 3-1
A. Removing Top Cover ........... 3-1
B. Removing Hinge .................. 3-2
C. Removing FAU Cable ........... 3-7
COPYRIGHT © 2000 CANON INC.
D. Removing Inverter Cover
......................................... 3-10
E. Attaching the Inverter Cover
......................................... 3-11
CANON FAU S-11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
CHAPTER 3
I. PARTS REPLACEMENT
A. Removing Top Cover
1) Remove four screws from the lamp cover assembly, then slide the top cover to remove it.
1
2
3
q Screw
w Lamp Cover Assembly
e Top Cover
Figure 3-1
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
3-1
CHAPTER 3
B. Removing Hinge
1) Remove the top cover.
2) Push both hooks of the hinge cover to unhook it.
1
q Hinge Cover
Figure 3-2
3-2
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
CHAPTER 3
3) Stand the hinges then remove the hinge cover in the arrow direction in the figure.
1
2
q Hinge
w Hinge Cover
Figure 3-3
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
3-3
CHAPTER 3
4) Pull up the hinge spring to unhook it.
1
q Hinge Spring
Figure 3-4
3-4
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
CHAPTER 3
5) Turn the hinge in the arrow direction in the figure to remove it.
1
q Hinge
Figure 3-5
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
3-5
CHAPTER 3
6) Remove the left and right hinge springs from the hinge shaft.
1
q Hinge Spring
Figure 3-6
3-6
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
CHAPTER 3
C. Removing FAU Cable
1) Remove the top cover.
2) Open the inverter cover on the lamp cover assembly.
1
2
q Inverter Cover
w Lamp Cover Assembly
Figure 3-7
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
3-7
CHAPTER 3
3) Remove the FAU cable from the connector CN1 on the inverter PCB.
1
2
q FAU Cable
w Inverter PCB
Figure 3-8
3-8
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
CHAPTER 3
Note: When assembling, insert the FAU cable in the recess shown in the figure.
1
q FAU Cable
Figure 3-9
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
3-9
CHAPTER 3
D. Removing Inverter Cover
1) Remove the top cover.
2) Remove two screws from the inverter PCB to hold it, then remove the inverter cover.
1
2
3
4
q
w
e
r
Screw
Inverter Cover
Inverter PCB
Spacer
Figure 3-10
Note: Take care not to miss two spacers under the inverter PCB.
3 - 10
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
CHAPTER 3
E. Attaching the Inverter Cover
1) Place the inverter PCB on the inverter cover.
2
1
q Inverter PCB
w Inverter Cover
Figure 3-11
2) Draw FAU cable and lamp cable through the inverter cover, cover the inverter PCB with the
inverter cover, then hook two hooks in the front.
1
2
3
q
w
e
r
FAU Cable
Inverter Cover
Lamp Cable
Hook
4
Figure 3-12
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
3 - 11
CHAPTER 3
3) Close both sides of the inverter cover, place two spacers under the inverter PCB, then fasten
two screws to fix the inverter PCB.
Note: Insert the lamp cable in the recess shown in the figure.
1
4
3
2
q
w
e
r
Screw
Spacer
Lamp Cable
Recess
Figure 3-13
3 - 12
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
CHAPTER 4
MAINTENANCE AND SERVICING
I.
PERIODICAL REPLACEMENT PARTS
III. PERIODICAL SERVICING ........... 4-1
.......................................... 4-1
IV. SPECIAL TOOLS ........................ 4-1
II. CONSUMABLE PARTS DURABILITY
V.
SOLVENTS AND LUBRICANTS .... 4-1
........................................... 4-1
COPYRIGHT © 2000 CANON INC.
CANON FAU S-11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
CHAPTER 4
I. PERIODICAL REPLACEMENT PARTS
None
II. CONSUMABLE PARTS DURABILITY
None
III. PERIODICAL SERVICING
None
IV. SPECIAL TOOLS
None
V. SOLVENTS AND LUBRICANTS
None
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
4-1
CHAPTER 5
TROUBLESHOOTING
I.
POSSIBLE CAUSE AND CORRECTIVE
ACTION ................................... 5-1
COPYRIGHT © 2000 CANON INC.
CANON FAU S-11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
CHAPTER 5
I. POSSIBLE CAUSE AND CORRECTIVE ACTION
FAU-S11 may have a failure ”FAU lamp does not light”. Table 5-1 shows its possible cause
and corrective action.
I. POSSIBLE CAUSE AND CORRECTIVE ACTION
Cause
Corrective Action
Inverter PCB failure
FAU cable poor connection
Replace the inverter PCB
Reconnect the FAU cable
FAU cable failure
Replace the FAU cable
Lamp cover assembly failure
Replace the lamp cover assembly
Table 5-1
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
5-1
CHAPTER 6
PARTS CATALOG
FIGURE 100 .............................. 6-2
COPYRIGHT © 2000 CANON INC.
CANON FAU S-11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
FAU-S11
COPYRIGHT © 2000 CANON INC.
CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
6-1
FIGURE 100
FAU-S11
1
4
2
3
4
3
5
7
5
8
10
6
9
10
11
8
8
12
6-2
COPYRIGHT © 2000 CANON INC.
CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
R
A
N
K
Q'
T
Y
FIGURE
&
KEY NO.
PART NUMBER
100-01
NIP-N406-400
1
HINGE, LEFT
02
NIP-N406-300
1
HINGE, RIGHT
03
NIM-L103-600
2
SPRING, 1
04
NIM-L103-500
2
SPRING, 2
05
NIP-N219-400
2
COVER, HINGE
06
NIP-N218-700
1
COVER, TOP
07
NIA-YFSC-087
1
CABLE, I/F
08
NIS-X300-874
6
SCREW, M3x8, SELF-TAPP
09
NIP-S200-500
1
COVER, INVERTER
10
NIM-U200-100
2
SPACER
11
NIA-YFSC-123
1
FLUORESCENT LAMP ASSEMBLY
12
NIA-YFSC-111
1
DOCUMENT COVER PP (F)
COPYRIGHT © 2000 CANON INC.
DESCRIPTION
SERIAL NUMBER/REMARKS
CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
6-3
APPENDIX
I.
GENERAL CIRCUIT
DIAGRAM .................................. A-1
COPYRIGHT © 2000 CANON INC.
II. INVERTER PCB CIRCUIT DIAGRAM
........................................... A-2
CANON FAU S-11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
FAU Lamp 1
FAU Lamp 2
I. GENERAL CIRCUIT DIAGRAM
CN2
1 2 3
CHK_FAU
FAU_LAMP
GND
CHK_FAU
FAU_LAMP
GND
1 2 3
CN3
CHK_FAU
FAU_LAMP
GND
Inverter PCB
1 2 3
CN1
JP2
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
A-1
II. INVERTER PCB CIRCUIT DIAGRAM
L1
F1
T1
+VIN
Q1
C2
CN2-3
C3
R1
CN3-3
C1
R2
Q2
R3
CN2-1
CN3-1
GND
A-2
COPYRIGHT © 2000 CANON INC. CANON FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN (IMPRIME AU JAPON)
©JAPON)
2000 CANON INC. CANON0400M0.04-1
FAU-S11 REV.0 APR. 2000 PRINTED IN JAPAN
AU JAPON)
PRINTED IN JAPAN COPYRIGHT
(IMPRIME AU
CANON(IMPRIME
INC.