BOXLIGHT CP-775i User`s manual

BEDIENUNGSANLEITUNG
Bitte lessen Sie diese Bedienungsanleitung zugunsten der korrekten Bedienung
aufmerksam.
MANUEL D'UTILISATION
Nous vous recommandons de lire attentivement ce manuel pour bien assimiler le
fonctionnement de l'appareil.
MANUALE D'ISTRUZIONI
Vi preghiamo voler leggere attentamente il manuale d'sitruzioni in modo tale da poter
comprendere quanto riportato ai fini di un corretto utilizzo del proiettore.
MANUAL DE USUARIO
Lea cuidadosamente este manual del usuario para poder utilizar corretamente el
producto.
GEBRUIKSAANWIJIZING
Lees voor het qebruik alstublieft deze handleiding aandachtig door, om volledig profijt te
hebben van de uitgebreide mogelijkheden.
BRUKERHÅNDBOK
Vennligst les denne bruksanvisningen grundig for å være garantert driftssikker bruk.
INSTRUÇÕES DO PROPRIETÁRIO
Para assegurar o uso correto do equipamento, por favor leia atentamente este manual do
usuário.
TECHNICAL
REGULATORY NOTICES
Downloaded From projector-manual.com Boxlight Manuals
ENGLISH
ITALIANO FRANÇAIS DEUTSCH
Please read this user's manual thoroughly to ensure correct usage through understanding.
NEDERLANDS ESPAÑOL
USER'S MANUAL
NORSK
CP-775i
TECHNICAL PORTGÊS
Multimedia LCD Projector
Multimedia LCD Projector
ENGLISH
USER'S MANUAL
Thank you for purchasing this LCD projector.
WARNING • Please read the accompanying manual “SAFETY
INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct
usage through understanding. After reading, store this instruction manual in a
safe place for future reference.
NOTE • The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in this manual
• The reproduction, transmission or use of this document or contents is not permitted without
express written authority.
TRADEMARK ACKNOWLEDGMENT : PS/2, VGA and XGA are registered trademarks of
International Business Machines Corporation. Apple, Mac and ADB are registered trademarks of
Apple Computer, Inc. VESA and SVGA are trademarks of the Video Electronics Standard
Association. Windows is a registered trademark of Microsoft Corporation. Carefully observe the
trademarks and registered trademarks of all companies, even when not mentioned.
CONTENTS
Page
Page
FEATURES .......................................2
BEFORE USE ...................................2
TROUBLESHOOTING ....................20
Contents of Package ..............................2
Part Names.............................................3
Loading the Batteries..............................5
INSTALLATION ................................6
Installation of the Projector and Screen........6
Angle Adjustment ...................................6
Cabling ...................................................7
Power Connection ..................................8
Example of System Setup ......................8
Plug & Play .............................................8
OPERATIONS ...................................9
Power ON ..................................................9
Power OFF ..............................................9
Basic Operation ....................................10
Setup Menu ..........................................12
Input Menu............................................13
Image Menu..........................................14
Options Menu .......................................15
No Signal Menu ....................................16
MAINTENANCE ..............................17
Lamp.....................................................17
Air Filter ................................................19
Other Maintenance ...............................19
OSD Message ......................................20
Indicators Message ..............................21
Symptom ..............................................22
SPECIFICATIONS...........................23
WARRANTY .......................................24
.......................................................................................
TABLES
Table 1. Installation Reference.................6
Table 2. Cabling .......................................7
Table 3. Basic Operation ........................10
Table 4. Setup Menu ..............................12
Table 5. Input Menu................................13
Table 6. Image Menu..............................14
Table 7. Options Menu ...........................15
Table 8. No Signal Menu ........................16
Table 9. OSD Message ..........................20
Table 10. Indicators Message ................21
Table 11. Symptom ................................22
Table 12. Specifications .........................23
.......................................................................................
For "TECHNICAL" and "REGULATORY
NOTICE", see the end of this manual.
Downloaded From projector-manual.com Boxlight Manuals
ENGLISH-1
FEATURES
This liquid crystal projector is used to project various computer signals as well as NTSC / PAL /
SECAM video signals onto a screen. Little space is required for installation and large images can
easily be realized.
Outstanding Brightness
The UHB lamp and high-efficiency optical system assure a high level of brightness.
Partial Magnification Function
Interesting parts of images can be magnified for closer viewing.
Distortion Correction Function
Distortion-free images are quickly available.
Extra-low Noise Function
Acoustic noise level from the unit can be reduced.
BEFORE USE
Contents of Package
Make sure all of the following items are included in the package. If anything is missing, please
contact BOXLIGHT at 800-762-5757 or 360-779-7901.
NOTE • Keep the original packing material for future reshipment.
Power Cord
(US Type)
Power Cord
(Europe Type)
MANUALE D'ISTRUZIONI
Vi preghiamo voler leggere attentamente il manuale d'sitruzioni in modo tale da poter
comprendere quanto riportato ai fini di un corretto utilizzo del proiettore.
MANUAL DE USUARIO
Lea cuidadosamente este manual del usuario para poder utilizar corretamente el
producto.
GEBRUIKSAANWIJIZING
Lees voor het qebruik alstublieft deze handleiding aandachtig door, om volledig profijt te
hebben van de uitgebreide mogelijkheden.
BRUKERHÅNDBOK
Vennligst les denne bruksanvisningen grundig for å være garantert driftssikker bruk.
INSTRUÇÕES DO PROPRIETÁRIO
Para assegurar o uso correto do equipamento, por favor leia atentamente este manual do
usuário.
TECHNICAL
REGULATORY NOTICES
ITALIANO FRANÇAIS DEUTSCH
MANUEL D'UTILISATION
NEDERLANDS ESPAÑOL
Bitte lessen Sie diese Bedienungsanleitung zugunsten der korrekten Bedienung
aufmerksam.
Nous vous recommandons de lire attentivement ce manuel pour bien assimiler le
fonctionnement de l'appareil.
NORSK
USER'S MANUAL
Please read this user's manual thoroughly to ensure correct usage through understanding.
BEDIENUNGSANLEITUNG
TECHNICAL PORTGÊS
Multimedia LCD Projector
CP-775i
ENGLISH
Projector
RGB Cable
Mouse cable
(PS/2)
Component
Video Cable
(with green lead)
User’s Manual
(this manual)
Safety Instructions
BLANK
STANDBY/ON
LASER
VIDEO
RGB
AUTO
MENU
KEYSTONE
MENU SELECT
RESET
POSITION
Batteries
for Remote Control
Transmitter
Carrying Bag
Downloaded
From projector-manual.com Boxlight Manuals
ENGLISH-2
FREEZE
MAGNIFY
PinP
MUTE
OFF
VOLUME
Remote Control
Transmitter
Part Names
Speaker
Zoom Knob
Focus Ring
Remote Control Sensor
Lens
Foot Adjuster
Carrying Handle
AC Inlet
(to the Power Cord)
Power Switch
Foot Adjuster
Ventilation Openings
(Intake)
Lens Cap
FRONT/LEFT VIEW OF
THE PROJECTOR
Control Panel (Refer to P.9 "OPERATIONS")
INPUT Button
LAMP Indicator
TEMP Indicator
POWER Indicator
RESET Button
MENU Button
STANDBY/ON Button
KEYSTONE Button
Foot Adjuster Button
Filter Cover
Air Filter and Intake
for the Cooling Fan
(
)
Ventilation Openings
(exhaust)
REAR/RIGHT VIEW OF
THE PROJECTOR
S-VIDEO Terminal
Remote Control Sensor
COMPONENT VIDEO
Y Terminal
CB/PB Terminal
CR/PR Terminal
DVI Terminal
RGB IN 1 Terminal
COMPONENT VIDEO
CR/PR CB/PB Y
VIDEO IN Terminal
DVI
1
AUDIO
IN
AUDIO 1
IN
AUDIO IN R Terminal
R
L
2
RGB IN
RGB IN 2 Terminal
2
S-VIDEO IN
VIDEO IN
AUDIO OUT
USB
RGB OUT
CONTROL
AUDIO IN L Terminal
CONTROL Terminal
AUDIO IN 1 Terminal
RGB OUT Terminal
AUDIO IN 2 Terminal
AUDIO OUT Terminal
Terminal Panel
(Refer below)
USB Terminal
TERMINAL PANEL
Downloaded From projector-manual.com Boxlight Manuals
ENGLISH-3
ENGLISH
BEFORE USE (continued)
BEFORE USE (continued)
Part Names (continued)
BLANK Button
STANDBY/ON Button
VIDEO Button
K
STAN
Disk Pad
LASER Button
N
BLA
DBY/O
N
ER
LAS
RGB Button
B
RG
MOUSE / RIGHT Button
O
VIDE
Used to operate the
mouse shift function and
left click function.
Used to click the right
mouse button.
KEYSTONE Button
AUTO Button
MENU Button
O
AUT
MENU SELECT Button
Used to click the left
mouse button.
,
,
,
Button
Used to operate the
mouse shift function.
M
RESET Button
Used to click the right
mouse button.
TONE
KEYS
ENU
CT
ELE
S
NU
ME
ET
RES
ION
POSIT
E ZE
FRE
PinP Button
PinP
FREEZE Button
TE
MU
NIFY
MAG
OFF
MUTE Button
M
VOLU
E
VOLUME Button
POSITION Button
REMOTE CONTROL
TRANSMITTER
(Refer to P.9 "OPERATIONS")
MAGNIFY Button
These functions work when the mouse control function is activated. Remember, the POSITION,
BLANK ON and MENU ON functions disable the mouse control function.
WARNING • The laser pointer of the remote control transmitter is used in
place of a finger or rod. Never look directly into the laser beam outlet or point
the laser beam at other people. The laser beam can cause vision problems.
CAUTION • Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation exposure.
AVOID EXPOSURELASER RADIATIONS IS
EMITTED FROM THIS
APERTURE
C A U T I O N
LASER RADIATIONDO NOT STARE INTO BEAM
MAX. OUTPUT: 1mW
WAVE LENGTH: 650nm
CLASS2 LASER PRODUCT
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS2 LASER PRODUCT
MAX. OUTPUT: 1mW
WAVE LENGTH: 650nm
IEC60825-1 : 1993+A1:1997
Complies with 21 CFR 1040. 10 and 1040. 11 except for deviations
pursuant to Laser Notice No.50, dated 2001.7.26
SMK CORPORATION
6-5-5 Togoshi Shinagawa-ku, Tokyo, JAPAN 142-8511
MANUFACTURED Novemver 2001
PLACE OF MANUFACTURER: A
NOTE • Keep the remote control transmitter away from children and pets.
• Do not give the remote control transmitter any physical impact. Take care not to drop.
• Do not place the heavy objects on the remote control transmitter.
• Do not wet the remote control transmitter or place it on any wet object.
• Do not place the remote control transmitter close to the cooling fan of the projector.
• Do not disassemble the remote control transmitter.
Downloaded
From projector-manual.com Boxlight Manuals
ENGLISH-4
BEFORE USE (continued)
Install the AA batteries into the remote control
transmitter.
1. Remove the battery cover.
Push the knob while lifting up the battery cover.
2. Load the batteries.
Make sure the plus and minus poles are correctly
oriented.
3. Close the battery cover.
ENGLISH
Loading the Batteries
1
2
CAUTION • Use only the specified batteries with this remote control
transmitter. Also, do not mix new and old batteries. This could cause
battery cracking or leakage, which could result in fire or personal injury.
• When loading the batteries, make sure the plus and minus terminals are
correctly oriented as indicated in the remote control transmitter. Incorrect
orientation could cause battery cracking or leakage, which could result in
personal injury or pollution of the surrounding environment.
• When you dispose the battery, you should obey the law in the relative area or
country.
• Keep the battery away from children and pets.
• When not to be used for an extended period, remove the batteries from the
remote control transmitter.
NOTE Replace the batteries when remote control transmitter operation becomes difficult.
Downloaded From projector-manual.com Boxlight Manuals
ENGLISH-5
INSTALLATION
Installation of the Projector and Screen
Refer to the drawing and table below for determining the screen size and projection distance.
The projection distances shown in the table below are for
full size (1024 x 768 dots).
a: Distance from the projector to the screen. (±10%)
Table 1. Installation Reference
Screen size
[inches (m)]
a [inches (m)]
Min.
Max.
40 (1.0)
60 (1.5)
62 (1.6)
94 (2.4)
82 (2.1)
123 (3.1)
80 (2.0)
127 (3.2)
164 (4.2)
100 (2.5)
160 (4.1)
205 (5.2)
120 (3.0)
192 (4.9)
246 (6.3)
150 (3.8)
241 (6.1)
308 (7.8)
200 (5.0)
323 (8.2)
411 (10.4)
Top View
a
Side View
CAUTION • Install the projector in a suitable environment according to instructions of
the accompanying manual “SAFETY INSTRUCTIONS” and this manual.
• When you fix this unit with a metal tool and the like, you must connect it with ground
wire; otherwise, fire or electric shock can result.
Connect the ground terminal of AC inlet of this unit with the ground terminal provided at the
building using an optional three-core power-supply cord.
• Please basically use liquid crystal projector at the horizontal position. If you use liquid
crystal projector by the lens up position, the lens down position and the side up position, this
may cause the heat inside to build up and cause damage. Be especially careful not to install it
with ventilation holes blocked.
• Do not install LCD projector in smoke effected environment. Smoke residue may buildup
on critical parts (i.e.LCD panel, Lens Assy etc.).
Angle Adjustment
Use the foot adjusters on the bottom of the projector to adjust the projection angle. It is variable
within 0˚ to 9˚ approximately.
Foot Adjusters
Press the foot
adjuster button
1. Lift up the front side of the projector, and pressing the foot adjuster button, adjust the projection
angle.
2. Release the button to lock at the desired angle.
3. Use the foot adjusters for fine adjustment. Do not force the adjuster screws. This
could damage the adjusters or cause the lock to fail.
CAUTION • Do not release the foot adjuster button unless the projector is being held;
otherwise, the projector could overturn or fingers could get caught and cause
personal injury.
Downloaded
From projector-manual.com Boxlight Manuals
ENGLISH-6
INSTALLATION (continued)
ENGLISH
Cabling
Refer to the table below for connecting each terminal of the projector to a device.
Table 2. Cabling
Function
RGB input
Terminal
RGB IN 1
RGB IN 2
RGB output
RGB OUT
DVI input
DVI
Audio input
(from the computer)
AUDIO IN 1
(interlocked with RGB IN 1 or DVI)
Cable
RGB cable
with D-sub 15-pin shrink jack
and inch thread screws
DVI cable with inch thread screws
Audio cable with stereo mini jack
AUDIO IN 2
(interlocked with RGB IN 2)
PS/2 mouse control
PS/2 mouse cable
ADB mouse control
ADB mouse cable
CONTROL
Serial mouse control
Serial mouse cable
RS-232C communication
RS-232C cable
USB mouse control
USB
USB cable
S-video input
S-VIDEO IN
S-Video cable
with mini DIN 4-pin jack
Video input
VIDEO IN
Video/Audio cable
COMPONENT VIDEO Y
Component video input
COMPONENT VIDEO CB/PB
Component Video cable
COMPONENT VIDEO CR/PR
Audio input
(from video equipment)
AUDIO IN L
AUDIO IN R
Video/Audio cable
or Audio cable with RCA jack
Audio output
AUDIO OUT
Audio cable with stereo mini jack
CAUTION • Incorrect connecting could result in fire or electrical shock.
Please read this manual and the separate “SAFETY INSTRUCTIONS”.
• Before connecting, turn off to all devices to be connected, except for the USB
cable.
• The cables may have to be used with the core set to the projector side. Use the
cables which are included with the projector or specified.
NOTE • Before connecting, read instruction manuals of the devices to be connected, and make sure that the
projector is compatible with the device.
• Secure the screws on the connectors and tighten.
• For some RGB input modes, the optional Mac adapter is necessary.
• To select the DVI input, the comuter may need some settings. See the manuals of the computer for details.
• Some computers may have multiple display screen modes. Use of some of these modes will not be possible
with this projector.
• Refer to the “TECHNICAL” section for the pin assignment of connectors and RS-232C communication data.
• When the DVI terminal is used, the RGB OUT terminal may not function.
Downloaded From projector-manual.com Boxlight Manuals
ENGLISH-7
INSTALLATION (continued)
Power Connection
Use the correct power cord depending on the power outlet to be used.
Connect the AC inlet of the projector to the power outlet firmly by the power cord.
CAUTION • Be carful in handling the power
cord according to instructions of the
accompanying manual "SAFETY INSTRUCTIONS"
and this manual.
• Connect the power cord firmly. Avoid using a
loose, unsound outlet or failed contact.
Power
outlet
Power Cord
AC Inlet
Example of System Setup
Display
Monitor
COMPONENT VIDEO
CB/PB
Y
CR/PR
DVI
DVD Player
1
AUDIO
IN
R
AUDIO 1
IN
L
2 AUDIO OUT
2
USB
RGB OUT
S-Video Tape
Recorder
RGB IN
S-VIDEO IN
VIDEO IN
CONTROL
Computer
(notebook type)
Speaker with
amplifier
Computer
(desktop type)
NOTE • When connecting with a notebook computer, set the proper RGB external image output
(setting CRT display or simultaneous display of LCD and CRT). Please read instruction manual of
the notebook for more information.
Plug & Play
This projector is VESA DDC 1/2B compatible. Plug & play is possible by connecting to a computer
that is VESA DDC (Display Data Channel) compatible.
Please use this function by connecting the RGB cable with RGB IN 1 terminal (DDC 1/2B compatible), or by connecting a DVI cable with DVI terminal (DDC 2B
compatible). Plug & play may not operate by other connections.
NOTE • Plug & play is a system configured with peripheral equipment including a computer,
display and an operating system.
• This projector is recognized as a plug & play monitor. Use the standard display drivers.
• Plug & play may not operate by the computer to connect. Use the RGB IN 2 terminal if plug &
play does not operate correctly.
Downloaded
From projector-manual.com Boxlight Manuals
ENGLISH-8
STANDBY/ON Button
STANDBY/
ON Button
BLANK
STANDBY/ON
LASER
VIDEO
POWER Indicator
Zoom Knob
Focus Ring
RGB
AUTO
MENU
KEYSTONE
MENU SELECT
RESET
POSITION
FREEZE
MAGNIFY
PinP
MUTE
OFF
Power Switch
Lens Cap
VOLUME
Power ON
1. Check that the power cord is connected correctly.
2. Set the power switch to [ | ]. The standby mode is selected, and the POWER indicator is turned to
orange.
3. Press the STANDBY/ON button
on the control panel or the remote control transmitter.
Warm-up begins and the POWER indicator blinks in green.
4. The POWER indicator ceases blinking and turns to green when power is on. Remove the lens
cap.
5. Adjust picture size using the zoom knob.
6. Adjust focus using the focus ring .
Power OFF
1. Press the STANDBY/ON button
on the control panel or the remote controller. Then,the
message "Power off?" will appear on the screen, and the message will disappear by any operation
or no operation for 5 seconds. During this message indication, press the STANDBY/ON
button again. The projector lamp is extinguished and lamp cooling begins. The POWER indicator
blinks orange during lamp cooling. Pressing the STANDBY/ON button
has no effect while
the POWER indicator is blinking.
2. The system assumes the Standby mode when cooling is complete, and the POWER indicator
ceases blinking and changes to orange. Check that the indicator is orange and set the power
switch to [O].
3. The POWER indicator is extinguished when power is off. Do not forget to attach the lens cap.
WARNING • Please read this manual, and the separate “SAFETY
INSTRUCTIONS” thoroughly before using the equipment. Always ensure that
the equipment is used safely.
NOTE • Except in emergencies, follow the above-mentioned procedure for turning power off.
Incorrect procedure will reduce the life of the projector lamp and LCD panel.
• To prevent any trouble, turn on/off the projector when the computer or video tape recorder is OFF.
Providing a RS-232C cable is connected, turn on the computer before the projector.
• When a projector continues projecting the same image, the image may remain as an afterimage.
Please do not project the image same for a long time.
Downloaded From projector-manual.com Boxlight Manuals
ENGLISH-9
ENGLISH
OPERATIONS
OPERATIONS (continued)
Basic Operation
The basic operations shown in Table 3 is performed from the supplied remote control transmitter or
the projector control panel. Items indicated by (*) may be used from the control panel.
Table 3 . Basic Operation
Item
Description
Select Input Signal (*) : Press the INPUT button.
RGB IN 1→RGB IN 2→DVI→ VIDEO IN → S-VIDEO IN → COMPONENT VIDEO (→ RGB IN 1)
Select RGB Input : Press the RGB button.
INPUT
SELECT
VIDEO IN / S-VIDEO IN / COMPONENT VIDEO → RGB IN 1 / RGB IN 2 / DVI
RGB IN 1 → RGB IN 2 → DVI (→ RGB IN 1)
Select Video Input : Press the VIDEO button.
RGB IN 1 / RGB IN 2 / DVI → VIDEO IN / S-VIDEO IN / COMPONENT VIDEO
VIDEO IN → S-VIDEO IN → COMPONENT VIDEO (→ VIDEO IN)
• The selected signal name is displayed for approximately 3 seconds when the input
signal is changed.
Set/Clear Position Adjustment Mode : Press the POSITION button.
The [
] icon is displayed in the POSITION mode.
POSITION
Image Position Adjustment: Press the
POSITION mode.
,
,
and
buttons in the
RESET (*)
Initialize Each Item : Select an item and press the RESET button.
Initialize Position Adjustment : Press the RESET button and the
POSITION mode. This function is valid only when RGB signal is input.
• Valid only in the MAGNIFY mode with a video signal is input.
• After approximately 10 seconds of inactivity the [ ] icon is extinguished and the
POSITION mode is cleared automatically.
•
, ,
and
buttons may operate as the mouse control button. Refer to page 4.
• Valid except for the VOLUME, LANGUAGE and H PHASE.
• The RESET button may operate as the mouse control button. Refer to page 4.
MAGNIFY
Set MAGNIFY Mode : Press the MAGNIFY
button.
Move Magnified Area : Run the POSITION in the MAGNIFY mode.
Adjust Magnification : Press the MAGNIFY
/
button in MAGNIFY
mode.
Clear MAGNIFY Mode : Press the MAGNIFY
button.
OFF
• The MAGNIFY mode is cleared by running or setting the AUTO, ASPECT, INPUT
SELECT or VIDEO, or by changing the input signal.
Set/Clear FREEZE Mode : Press the FREEZE button. The [II] icon is
displayed, and the image is frozen, in the FREEZE mode.
FREEZE
• The FREEZE mode is cleared by running or setting POSITION, VOLUME, MUTE,
Automatic Adjustment, BLANK ON/OFF, or MENU ON/OFF, or by changing the
input signal.
• Do not forget to clear frozen static images.
NOTE • Strong light and obstacles will interfere with operation of the remote control transmitter.
Downloaded
From projector-manual.com Boxlight Manuals
ENGLISH-10
OPERATIONS (continued)
ENGLISH
Items indicated by (*) may be used from the control panel.
Table 3. Basic Operation (continued)
Item
Description
VOLUME
Volume Adjustment : Press the VOLUME
MUTE
Set/Clear Mute Mode : Press the MUTE button. No sound is heard in the
MUTE mode.
AUTO
/
button.
Automatic Adjustment at RGB Input : Press the AUTO button. Horizontal
position(H.POSIT), vertical position (V.POSIT),clock phase (H.PHASE),
and horizontal size(H.SIZE) are automatically adjusted. Use with the
window at maximum size in the application display.
Automatic Adjustment at Video Input : Press the AUTO button. A signal
type appropriate for the input signal is selected automatically. Valid only
when AUTO is set for VIDEO on the menu.
• This operation requires approximately 10 seconds. It may not function correctly
with some input signals.
BLANK
ON/OFF
Set/Clear Blank Mode: Press the BLANK button. No image is displayed in
the Blank mode. The screen color is as set in BLANK on the Image menu.
Menu Display Start/Stop: Press the MENU button.
MENU
• The menu display is terminated automatically after approximately 10 seconds of
ON/OFF (*)
inactivity.
Select Menu Type: Press the MENU SELECT button. Allows the user to
select the normal menu or the single menu. Only the selected item is
displayed on the single menu, and other items are displayed with the
and
buttons as with the normal menu.
MENU
SELECT
• Valid only when the Setup menu is used. Push the MENU SELECT button after
selecting items such as "BRIGHTNESS".
• The MENU SELECT button may operate as the mouse control button. Refer to
page 4.
Normal menu
Single menu
(MENU SELECT)
SETUP
INPUT
BRIGHT
CONTRAST
V POSIT
H POSIT
H PHASE
H SIZE
COLOR BAL R
COLOR BAL B
ASPECT
P.IN P.
MODE
IMAGE
OPT.
0
-2
100
100
+1
800
0
0
CONTRAST
-2
Select Mode of P.IN P. Display : Press the PinP button.
Small → Large → P.IN P. off ( → Small)
• P.IN P. function suoerimposes a video image over RGB or DVI signals.
Set / Clear KEYSTONE Mode (*) : Press the KEYSTONE
button.
Select
KEYSTONE
Mode
:
Press
the
/
button
in
the
KEYSTONE
KEYSTONE
↔
Horizontal
mode. Vertical
Adjust KEYSTONE : Press the
/
button.
Downloaded From projector-manual.com Boxlight Manuals
ENGLISH-11
OPERATIONS (continued)
Setup Menu
SETUP
The following adjustments and settings are possible
when SETUP is selected at the top of the menu. Part
of the Setup menu differs between RGB input and
video input. Select an item with the
and
buttons, and start operation. Use the Single menu to
reduce menu size (see Table 3, MENU SELECT).
Table 4. Setup Menu
Item
INPUT
BRIGHT
CONTRAST
V POSIT
H POSIT
H PHASE
H SIZE
COLOR BAL R
COLOR BAL B
ASPECT
IMAGE
SETUP
OPT.
INPUT
IMAGE
OPT.
0
+1
+1
0
0
0
0
0
BRIGHT
CONTRAST
SHARPNESS
COLOR
TINT
H PHASE
COLOR BAL R
COLOR BAL B
ASPECT
0
-2
100
100
+1
800
0
0
VIDEO
S-VIDEO
COMPONENT VIDEO
RGB IN 1
RGB IN 2
DVI
Description
↔ Light
RGB IN 1
RGB IN 2
DVI
VIDEO
S-VIDEO
COMPONENT
✔
✔
✔
BRIGHT
Adjustment: Dark
CONTRAST
Adjustment: Weak
↔ Strong
✔
✔
✔
V POSIT
Adjustment: Down
↔ Up
✔
-
-
H POSIT
Adjustment: Left
↔ Right
✔
-
-
H PHASE
Adjustment: Left
↔ Right
• Adjust to eliminate flicker.
✔
-
✔
H SIZE
↔ Large
• The image may not be displayed correctly if the horizontal
size is excessive. In such cases, press the RESET button,
and initialize the horizontal size.
✔
-
-
SHARPNESS
Adjustment: Soft
↔ Clear
-
-
✔
COLOR
Adjustment: Light
↔ Dark
-
-
✔
-
-
✔
Adjustment: Small
TINT
↔ Green
• Valid only when NTSC or NTSC 4.43 signal is received.
Adjustment: Red
COLOR BAL R Adjustment: Light
↔ Dark
✔
✔
✔
COLOR BAL B Adjustment: Light
↔ Dark
✔
✔
✔
✔
✔
-
-
-
✔
Select Image Aspect Ratio :
Full [
]
↔
16:9[
]
Select Position of Image:
Press the
button while 16:9[
] is selected.
Center →
Down →
Up ( → Center
)
ASPECT
Select Image Aspect Ratio:
4:3[
]
↔
16:9[
]
↔
4:3 small[
Select Position of Image :
Press the
button while 16:9[
] / 4:3 small[
is selected.
Center →
Down →
Up ( → Center
)
]
]
• 4:3 small cannot be selected with the input of 720p or
1080i component.
• 4:3 small may not be displayed correctly with some input
signals.
Downloaded
From projector-manual.com Boxlight Manuals
ENGLISH-12
Input Menu
The following functions are available when INPUT is selected on the
menu. Select an item with the
and
buttons, and start or stop
operation with the
and
buttons. The function indicated (**) are
effective on video input mode only, not on RGB input mode, except in
the P.IN P. window on RGB input mode.
Table 5. Input Menu
Item
AUTO
SETUP
AUTO
RGB
VIDEO
HDTV
INPUT
IMAGE
OPT.
EXECUTE
CANCEL
Description
Automatic Adjustment at RGB Input: Select the EXECUTE with the
button. Horizontal position (H.POSIT), vertical position (V.POSIT), clock
phase (H.PHASE), and horizontal size (H.SIZE) are automatically adjusted.
Use with the window at maximum size in the application display.
Automatic Adjustment at Video Input: Select the EXECUTE with the
button. A signal type appropriate for the input signal is selected
automatically when EXECUTE is selected automatically. Valid only when
AUTO is set for VIDEO on the menu.
• This operation requires approximately 10 seconds. It may not function correctly with
some input signals. Pressing the AUTO button in this case may correct this problem.
• This function is the same as for the AUTO function in Basic operation.
RGB
Displays RGB Input Frequency: Displays the horizontal and vertical sync
signal frequencies for RGB input.
• Valid only at RGB input.
Select Video Signal Type: Select the signal type with the
and
buttons. Select NTSC, PAL, SECAM, NTSC4.43, M-PAL, or N-PAL as
appropriate for the input signal. The selection of AUTO enables and
executes the function AUTO (Automatic Adjustment at Video Input), except
for the N-PAL input.
VIDEO (**)
HDTV
• Use this function when the image becomes unstable (eg. the image becomes
irregular, or lacks color) at VIDEO/S-VIDEO input.
• Automatic Adjustment requires approximately 10 seconds. It may not function
correctly with some input signals. Pressing the AUTO button in this case may correct
this problem except for the N-PAL input.
• For the COMPONENT VIDEO input, this function is not effective and the signal
type is distinguished automatically. Refer to the item HDTV of the OPT. Menu for the
signal of HDTV.
Select HDTV mode: Select the 1035i mode or 1080i mode suitable for the
input signal with the
/
button.
Downloaded From projector-manual.com Boxlight Manuals
ENGLISH-13
ENGLISH
OPERATIONS (continued)
OPERATIONS (continued)
Image Menu
SETUP
The following adjustments and settings are available when IMAGE is
selected on the menu. Select an item with the
and
buttons, and
start or stop operation with the
and
buttons.
INPUT
BLANK
START UP
MyScreen
MIRROR
P. IN P. POSIT
P. IN P. INPUT
GAMMA
IMAGE
OPT.
MyScreen
ORIGINAL
Table 6. Image Menu
Item
BLANK
Description
Select Blank Screen: Select the screen in case of the BLANK mode with the
/
button. The selected one (MyScreen, ORIGINAL or one colors) is displayed when the
BLANK mode is ON.
MyScreen is a mode that the customer-customized screen is displayed. This is the
blue screen at the factory setting. Refer to the description of MyScreen below.
ORIGINAL is a mode that the factory fixed screen is displayed.
• When MyScreen or ORIGINAL is selected, the screen is going to the black after several minutes.
START UP
Select Start Up Screen: Select the screen in case of no signal input with the
/
button. The selected one (MyScreen, ORIGINAL or TURN OFF) is displayed when
no signal is input.
My Screen is a mode that the customer-customized screen is displayed. This is the
blue screen at the factory setting. Refer to the description of MyScreen below.
ORIGINAL is a mode that the factory fixed screen is displayed.
TURN OFF displays the blue screen.
• When MyScreen or ORIGINAL is selected, the screen is going to the black after several minutes.
MyScreen
Set MyScreen Mode: Select the EXECUTE with the
button to display the
MyScreen menu and set the MyScreen mode for BLANK and START UP functions.
ESC clears and closes the menu box.
NORM. is default of the MyScreen menu.
FREEZE freezes the image and displays the frame to capture.
Press the
button after freeze to go to the MyScreen Capture Position mode.
In the MyScreen Capture Position mode, the buttons
, ,
and
allow to
move the frame to capture.
After adjusting the position, press the KEYSTONE button to go to the MyScreen
Display Size mode.
To cancel freezing and return to the NORM. of the MyScreen menu, press the
RESET button.
In the MyScreen Display Size mode, select the magnification x1, x2 or FULL with
the button
/ . After selecting the magnification, press the KEYSTONE button to
go to the CAPT. mode and start capturing.
To return to the MyScreen Capture Position mode, press the RESET button.
CAPT. executes a capturing the image. It requires about 20 seconds. After capturing,
the captured image will be displayed for about 10 seconds.
MIRROR
Select Mirror Status: Select mirror status with
P. IN P.
POSIT
Select Position of P. in P. Display : Press the
or
button.
↔
↔
↔
• P.IN P. function suoerimposes a video image over RGB or DVI signals.
P. IN P.
INPUT
Select signal of P. in P. Display : Press the
VIDEO
↔
S-VIDEO
GAMMA
Select Gamma Mode: Select the gamma mode with the
NORMAL
↔
CINEMA
↔
DYNAMIC
Downloaded
From projector-manual.com Boxlight Manuals
ENGLISH-14
/
or
button.
button.
/
button.
Options Menu
SETUP
The following adjustments and settings are available when OPT. is
selected on the menu. Select an item with the
and
buttons, and
start or stop operation with the
and
buttons.
Table 7. Options Menu
Item
INPUT
IMAGE
OPT.
16
VOLUME
MENU COLOR
LANGUAGE
AUTO OFF
SYNC ON G
WHISPER
IR REMOTE
Description
↔
VOLUME
Reduce
MENU COLOR
Select Menu Background Color: Select with the
LANGUAGE
Select Menu Display Language: Select with the
/
button.
Set AUTO OFF: Set 1~99 minutes with the
/
button. The system
automatically enters the standby mode when a signal is not received for
the set time.
Clear AUTO OFF: Select STOP (0 min.) with the
button. When
STOP is selected the system does not enter the standby mode even if
no signal is received.
SYNC ON G Valid: Select TURN ON with the
button.
SYNC ON G Invalid: Select TURN OFF with the
button.
AUTO OFF
SYNC ON G
WHISPER
/
button.
• May not be displayed correctly with some input signals when SYNC ON G is
valid. In such cases, remove the signal connector so that no signal is received,
set SYNC ON G to invalid, and reconnect the signal.
Set / Crear WHISPER Mode: Press the
/
button. When the
WHISPER is selected, the WHISPER mode is active. In the WHISPER
mode, acoustic noise level from the unit is reduced, and brightness level
on screen is a little lower.
Select Remote Control Sensor: Select the sensors to activate along
the menu with the
/
button. Use this function if the remote does
not work stably. The ambient light may affect the remote.
SETUP
IR REMOTE
Increase
INPUT
VOLUME
MENU COLOR
LANGUAGE
AUTO OFF
SYNC ON G
WHISPER
IR REMOTE
IMAGE
2
1
1
OPT.
3
2
3
: active
: inactive
Downloaded From projector-manual.com Boxlight Manuals
ENGLISH-15
ENGLISH
OPERATIONS (continued)
OPERATIONS (continued)
No Signal Menu
VOLUME
BLANK
START UP
MIRROR
MENU COLOR
LANGUAGE
AUTO OFF
SYNC ON G
WHISPER
IR REMOTE
The same adjustments and settings are available with the Image and
Options menus when the MENU button is pressed during display of the
“NO INPUT IS DETECTED ON ***” or “SYNC IS OUT OF RANGE
ON ***” message while no signal is received.Select an item with the
and
buttons, and start or stop operation with the
and
buttons.
16
Table 8. No Signal Menu
Item
Description
Reduce
VOLUME
BLANK
↔
Increase
• When this function is used, audio input is automatically switched to video. The audio input can
be switched by moving the DISK PAD left and right during the display of the volume adjustment
bar. The volume adjustment bar is displayed by pressing VOLUME
/
button.
Select Blank Screen: Select the screen in case of the BLANK mode with the
/
button. The selected one (MyScreen, ORIGINAL or one colors) is displayed when the
BLANK mode is ON.
MyScreen is a mode that the customer-customized screen is displayed. This is the
blue screen at the factory setting. Refer to the description of MyScreen below.
ORIGINAL is a mode that the factory fixed screen is displayed.
• When MyScreen or ORIGINAL is selected, the screen is going to the black after several minutes.
START UP
Select Start Up Screen: Select the screen in case of no signal input with the
/
button.
The selected one (MyScreen, ORIGINAL or TURN OFF) is displayed when no signal is input.
My Screen is a mode that the customer-customized screen is displayed. This is the
blue screen at the factory setting. Refer to the description of MyScreen below.
ORIGINAL is a mode that the factory fixed screen is displayed.
TURN OFF displays the blue screen.
• When MyScreen or ORIGINAL is selected, the screen is going to the black after several minutes.
MIRROR
Select Mirror Status: Select the mirror status with the
/
MENU COLOR Select Menu Background Color: Select the color with the
LANGUAGE
AUTO OFF
SYNC ON G
WHISPER
IR REMOTE
Select Menu Display Language: Select the language with the
button.
/
button.
/
button.
Set AUTO OFF: Set 1~99 minutes with the
/
button. The system
automatically enters the standby mode when a signal is not received for the set time.
Clear AUTO OFF: Select the STOP (0 min.) with the
button. When the STOP is
selected the system does not enter the standby mode even if no signal is received.
SYNC ON G Valid: Select the TURN ON with the
button.
SYNC ON G Invalid: Select the TURN OFF with the
button.
• May not be displayed correctly with some input signals when the SYNC ON G is valid. In such
cases, remove the signal connector so that no signal is received, set the SYNC ON G to invalid,
and reconnect the signal.
Set / Crear WHISPER Mode: Press the
/
button. When the WHISPER is
selected, the WHISPER mode is active. In the WHISPER mode, acoustic moise level
from the unit is reduced, and brightness level on screen is a little lower.
Select Remote Control Sensor: Select the sensors to activate along the menu with
the
/
button. Use this function if the remote does not work stably. The ambient
light may affect the remote.
VOLUME
BLANK
START UP
MIRROR
MENU COLOR
LANGUAGE
AUTO OFF
SYNC ON G
WHISPER
IR REMOTE
2
1
1
3
2
3
: active
: inactive
Downloaded
From projector-manual.com Boxlight Manuals
ENGLISH-16
Lamp
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
Contact BOXLIGHT before replacing the lamp.
For the optional lamp, see the item “Optional Parts” of the Table 12.
Before replacing the lamp, switch power OFF, remove the power cord from the power outlet, and
wait approximately 45 minutes until the lamp has cooled. The lamp may explode if handled at high
temperatures.
WARNING • For disposal of used lamp, treat
according to the instruction of community
authorities.
• Since the lamp is made of glass, do not apply shock
to it and do not scratch it.
• Also, do not use old lamp. This could also cause
explosion of the lamp.
• Premature lamp failure MAY be caused by an
electronic component in the projector and not
necessarily the lamp. If unsure contact BOXLIGHT.
• If it is probable that the lamp has exploded (explosive
sound is heard), disconnect the power plug from the
power outlet and ask BOXLIGHT to replace lamp. The
lamp is covered by front glass, but in rare cases, the
reflector and the inside of the projector may be
damaged by scattered broken pieces of glass, and
broken pieces could cause injury when being handled.
• Do not use the projector with the lamp cover removed.
Lamp
Reflector
Front
glass
Lamp Life
Projector lamps have a finite life. The image will become darker, and hues will become weaker,
after a lamp has been used for a long period of time.
Replace the lamp if the LAMP indicator is red, or the CHANGE THE LAMP message appears
when the projector is switched ON. See Table 9 of P.20 and Table 10 of P.21.
NOTE • The LAMP indicator is also red when the lamp unit reaches high temperature. Before
replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again.
If the LAMP indicator is still red, replace the lamp.
Downloaded From projector-manual.com Boxlight Manuals
ENGLISH-17
ENGLISH
MAINTENANCE
MAINTENANCE (continued)
Replacing the Lamp
1. Switch the projector OFF, remove the power cord from the
power outlet, and wait at least 45 minutes for the unit to cool.
2. Prepare a new lamp.
3. Check that the projector has cooled sufficiently, and gently
turn it upside down.
4. Loosen the two screws as shown in the diagram, and remove
the lamp cover.
5. Loosen the three screws, and gently remove the lamp while
holding the grips. Touching the inside of the lamp case may
result in uneven coloring.
6. Install the new lamp and tighten the three screws firmly.
Also steadily push the opposite side of the screwed lamp into
the unit.
7. Replace the lamp cover in position and tighten the two
screws firmly.
8. Gently turn the projector right-side up.
CAUTION • Ensure that screws are tightened
properly. Screws not tightened fully may result
in injury or accidents.
• Do not use the projector with the lamp cover
removed.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp. When the lamp has been replaced after the LAMP
indicator is red, or the CHANGE THE LAMP message is displayed, complete the following
operation within ten minutes of switching power ON. The power will be turned off automatically in
over 10 minutes.
1. Switch power ON, and press the RESET button, for approximately three seconds. The ‘LAMP
xxxx hr’ message will appear on the lamp timer on the bottom of the screen.
2. Press the MENU button on the remote control transmitter, or the RESET button on the control
panel, while the lamp timer is displayed. The ‘LAMP xxxx → 0 ■ CANCEL’ message will
then appear.
3. Press the
and select 0, and wait until the timer display is cleared.
NOTE • Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always
when replacing the lamp. The message functions will not operate properly if the lamp timer is not
reset correctly.
Downloaded
From projector-manual.com Boxlight Manuals
ENGLISH-18
Air Filter
Cleaning the air Filter
The air filter should be cleaned as described below at intervals of approximately 100 hours.
1. Switch the projector power supply OFF, and remove the power cord from the power outlet.
2. Clean the air filter with a vacuum cleaner.
Replacing the Air Filter
Replace the air filter if contamination cannot be removed, or if it is damaged.
1. Remove the filter cover.
2. Remove the old filter.
3. Set the new filter and the filter cover.
CAUTION • Switch power OFF and remove the power cord from the power
outlet before beginning maintenance work. Please read the separate “SAFETY
INSTRUCTIONS” thoroughly to ensure that maintenance is performed correctly.
• Replace the air filter if contamination cannot be removed, or if it is damaged.
Contact BOXLIGHT for service. For the optional air filter, see the item “Optional
Parts" of the Table 12.
• Do not use the equipment with the air filter removed.
• When the air filter is clogged with dust etc. the power supply is switched OFF
automatically to prevent the temperature rising inside the projector.
Other Maintenance
Maintenance Inside the Equipment
For safety reasons, ensure that the equipment is cleaned and checked by BOXLIGHT once every
two years. Maintaining the equipment by yourself is dangerous.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Cabinet and Remote control transmitter
Gently wipe with a soft cloth. If dirt and stains etc. are not easily removed, use a soft cloth
dampened with water, or water and a neutral detergent, and wipe dry with a soft, dry cloth.
CAUTION • Switch power OFF and remove the power cord from the power
outlet before beginning maintenance work. Please read the separate “SAFETY
INSTRUCTIONS” thoroughly to ensure that maintenance is performed correctly.
• Do not use detergents or chemicals other than those noted above (e.g. benzene
or thinners).
• Do not use cleaning sprays.
• Do not rub with hard materials, or tap the equipment.
Downloaded From projector-manual.com Boxlight Manuals
ENGLISH-19
ENGLISH
MAINTENANCE (continued)
TROUBLESHOOTING
OSD Message
The messages as described below may appear on the screen at power ON. Take the appropriate
measures when such messages appears.
Table 9. OSD Message
Message
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
(*1)
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
THE POWER WILL TURN OFF
AFTER ** hr.
(*1)
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
THE POWER WILL
TURN OFF
AFTER 0 hr.
Contents
The usage time of lamp will be reaching 2000 hr
shortly.(*2)
It is recommended to replace the lamp soon. Prepare a
new lamp as a replacement.
The usage time of lamp will be reaching 2000 hr shortly.
It is recommended to replace the lamp within * *
hours.(*2)
It might be happened that the lamp is cut off before * * hr
by any chance. Power will be switched OFF
automatically in * * hours. Replace the lamp as shown in
P.17~18 “Lamp”. Always reset the lamp timer after
replacing the lamp.
The usage time of lamp is about to reach. Power will be
switched OFF in a few minutes.(*2)
Switch power OFF immediately and replace the lamp as
shown in P.17 ~18 “Lamp”. Always reset the lamp timer
after replacing the lamp.
NO INPUT IS DETECTED
ON ***
No input signal found.
Check signal input connections and signal sources.
SYNC IS OUT OF RANGE
ON ***
The horizontal or vertical frequency of the input signal is
not within the specified range.
Check the specifications of the equipment and the signal
source.
NOTE (*1) This message is cleared automatically after approximately three minutes, and
appears every time power is switched ON.
(*2) The unit has a function to turn the power off which will be active when the usage time reaches
2000 hr. However the life of lamp might be much different among lamps, so that it might be
happened that a lamp is cut off before the function is active.
Downloaded
From projector-manual.com Boxlight Manuals
ENGLISH-20
Indicators Message
The POWER indicator, LAMP indicator, and TEMP indicator are lit and blank as follows. Take the
appropriate measures.
Table 10. Indicators Message
POWER LAMP TEMP
indicator indicator indicator
Contents
Lights
orange
Turns off Turns off The Standby mode has been set.
Blinks
green
Turns off Turns off Warming up. Please wait.
Lights
green
Turns off Turns off ON. Normal operation possible.
Blinks
orange
Turns off Turns off Cooling. Please wait.
Blinks red
-
Blinks
/Lights red
Lights
red
Blinks
/Lights red
Blinks
red
Cooling. Please wait.
The error is found. Take the appropriate measures when the
POWER indicator ceases blinking
Lamp is not lit.
The interior of the equipment may be too hot. Switch power OFF,
wait 20 minutes until the equipment cools, and check whether the
Turns off
ventilation openings are blocked, whether the air filter is dirty, or
whether the ambient temperature exceeds 35 °C. And switch
power ON again. Replace the lamp if the same problem occurs.
-
Turns off
Lamp or lamp cover is not found, or hasn’t been fitted in correctly.
Switch power OFF, and wait for 45 minutes until the equipment
cools. Check fitting of the lamp and lamp cover, and switch power
ON again. Contact BOXLIGHT if the same problem occurs again.
The cooling fan is not operating.
Switch power OFF, and wait for 20 minutes until the equipment
cools. Check for foreign matters in the fan, and switch power ON
again. Contact BOXLIGHT if the same problem occurs again.
The interior of the equipment is too hot.
Switch power OFF, and wait for 20 minutes until the equipment
Blinks
cools. Check whether the ventilation openings are blocked,
Turns off Lights red
whether the air filter is dirty, or whether the ambient temperature
/Lights red
exceeds 35 °C. Then switch power ON again. Contact BOXLIGHT
if the same problem occurs again.
The interior of the equipment is too cool.
Lights
Blinks
Blinks Check whether the ambient temperature is below 0°C. Contact
BOXLIGHT if the same problem occurs when the ambient
green
red
red
temperature is 0~35°C.
Blinks
Turns off
/Lights red
Blinks
red
NOTE When the internal temperature becomes excessive power is switched OFF automatically
for safety reasons, and the indicator is extinguished. Set the power switch to [O] and wait for 20
minutes until the equipment has cooled sufficiently.
Downloaded From projector-manual.com Boxlight Manuals
ENGLISH-21
ENGLISH
TROUBLESHOOTING (continued)
TROUBLESHOOTING (continued)
Symptom
Before requesting repair, consult the following chart. If the situation cannot be corrected, then
contact BOXLIGHT at 800-762-5757 or 360-779-7901.
Table 11. Symptom
Symptom
The power is not
turned on.
Possible cause
Remedy
The main power switch is not
turned on.
Turn on the main power switch.
The power cord is
disconnected.
Plug the power cord into an AC
power outlet.
The input is not correctly set.
Use the projector or remote control
transmitter to set.
10
No signal input.
Connect correctly.
7,8
The projector is not correctly
connected.
Connect correctly.
7,8
No video or audio.
Video is present but
The volume is set to minimum.
no audio.
Press VOLUME
on the remote
control or display the menu screen
and adjust the volume.
Mute is turned on.
Press the MUTE
The projector is not correctly
connected.
Connect correctly.
button.
Audio is present but The brightness adjustment knob Select BRIGHT with the MENU
button and the press the
button.
is rotated fully clockwise.
no video.
The lens cap is still attached.
Colors are pale and Color density and color
color matching is
matching are not correctly
poor.
adjusted.
Images are dark.
Video is blurred.
Page
Remove the lens cap.
8,9
11,15
11
7,8
12
9
Adjust the video.
12
Brightness and contrast are not
Adjust the video.
correctly adjusted.
12
The lamp is nearing the end of
its service life.
Replace with a new lamp.
17
WHISPER mode is set.
Clear WHISPER mode.
15
Focus or H PHASE is out of
adjustment.
Adjust the focus or H PHASE.
Downloaded
From projector-manual.com Boxlight Manuals
ENGLISH-22
9,12
Table 12. Specifications
Item
Product name
Liquid
crystal
panel
Specification
Liquid crystal projector
Panel size
2.3 cm (0.9 type)
Drive system
TFT active matrix
Pixels
786,432 pixels (1024 horizontal x 768 vertical)
Lens
Zoom lens F=1.7 ~ 2.1 f=36.8 ~ 47.8 mm
Lamp
250 W UHB
Speaker
1.0W+1.0W (stereo)
Power supply
AC100 ~ 120V, 4.5A / AC220 ~ 240V, 1.9A
Power consumption
410W
Temperature range
0 ~ 35°C (Operating)
Size
360 (W) x 106 (H) x 256.5 (D) mm
Weight (mass)
4.5 kg
1
RGB IN
RGB
signal
input
2
Video
signal
input
Video: Analog 0.7Vp-p, 75Ω terminator (positive)
H/V. sync.: TTL level (positive/negative)
Composite sync.: TTL level
D-sub 15-pin shrink jack
TMDS, DC: 150~1200 mV / AC: 1.56 Vp-p
TTL Level (Positive/Negative)
DVI
AUDIO IN
ENGLISH
SPECIFICATIONS
RGB1
DVI
RGB2
200mVrms, 50 kΩ (max. 3.0Vp-p)
Stereo mini jack
VIDEO IN
1.0Vp-p, 75Ω terminator
RCA jack
S-VIDEO IN
Brightness signal: 1.0Vp-p, 75Ω terminator
Color signal: 0.286Vp-p (NTSC, burst signal),75Ω terminator
0.300Vp-p (PAL/SECAM, burst signal),75Ω terminator
Mini DIN 4-pin jack
Y
1.0 Vp-p, 75 Ω Terminator (Positive)
COMPONENT
CB/CR 0.7 Vp-p, 75 Ω Terminator (Positive)
VIDEO
PB/PR 0.7 Vp-p, 75 Ω Terminator (Positive)
AUDIO IN
Signal
output
Control
functions
L
R
200mVrms, 50 kΩ (max. 3.0Vp-p)
RCA jack
RGB OUT
Video: Analog 0.7Vp-p, 75Ω output impedance (positive)
H/V. sync.: TTL level (positive/negative)
Composite sync.: TTL level
D-sub 15-pin shrink jack
AUDIO OUT
200mVrms, output impedance 1 kΩ (max. 3.0Vp-p)
Stereo mini jack
CONTROL
D-sub 15-pin shrink plug
USB
USB jack (B type)
Optional Parts
Lamp: CP-775i-930 (DT00471)
Air Filter: CP-775i-935 (NJ060131)
* For others, consult BOXLIGHT.
NOTE • This specifications are subject to change without notice.
Downloaded From projector-manual.com Boxlight Manuals
ENGLISH-23
WARRANTY
LIMITED WARRANTY
BOXLIGHT CORPORATION("BOXLIGHT") warrants that each Boxlight CP-775i ("the Product") sold
hereunder will conform to and function in accordance with the written specifications of BOXLIGHT. Said
limited warranty shall apply only to the first person or entity that purchases the Product for personal or business
use and not for the purpose of distribution resale. Said warranty shall continue for a period of two (2) years from
the date of such purchase. BOXLIGHT does not warrant that the Product will meet the specific requirements of
the first person or entity that purchases the Product for personal or business use. Lamp is warrantied for 120
days.
BOXLIGHT CORPORATION's liability for the breach of the foregoing limited warranty is limited to the repair
or replacement of the Product or refund of the purchase price of the Product, at BOXLIGHT's sole option. To
exercise the Purchaser's rights under the foregoing warranty, the Product must be returned at the Purchaser's sole
cost and expense, to BOXLIGHT or any authorized service center provided, however, that the Product must be
accompanied by a written letter explaining the problem and which includes (i) proof of purchase; (ii) the dealer's
name; (iii) the model and serial number of the Product. A return authorization number, issued by the
BOXLIGHT customer service department, must also be clearly displayed on the outside of the shipping carton
containing the Product.
WARRANTY LIMITATION AND EXCLUSION
BOXLIGHT CORPORATION shall have no further obligation under the foregoing limited warranty if the
Product has been damaged due to abuse, misuse, neglect, accident, unusual physical or electrical stress,
unauthorized modification, tampering, alterations, or service other than by BOXLIGHT or its authorized agents,
causes other than from ordinary use or failure to properly use the Product in the application for which said
Product is intended.
DISCLAIMER OR UNSTATED WARRANTIES
The warranty printed above is the only warranty applicable to this purchase.
All other warranties express or implied, Including, but not limited to, the implied warranties or merchantability
and fitness for a particular purpose are disclaimed. There are no warranties that extend beyond the face of hereof
and the forgoing warranty shall not be extended, altered or varied except by written instrument signed by
BOXLIGHT CORPORATION.
LIMITATION OF LIABILITY
It is understood and agreed that BOXLIGHT's liability whether in contract, in tort, under any warranty, in
negligence or otherwise, shall not exceed the return of the amount of the purchase price paid by purchaser and
under no circumstances shall BOXLIGHT be liable for special, indirect or consequential damages. The price
stated for the Product is a consideration in limiting BOXLIGHT's liability. No action regardless of form, arising
out of the agreement to purchase the product, may be brought by purchaser more than one year after the cause of
action has accrued.
Boxlight
19332 Powder Hill Place
Poulsbo, WA 98370-7407-USA
www.boxlight.com
U.S. and Canada 800-762-5757
International 360-779-7901
Downloaded
From projector-manual.com Boxlight Manuals
ENGLISH-24
*QR52531
*
Downloaded From
projector-manual.com
Boxlight Manuals
Printed in Japan