Montigo R620-ST Owner`s manual

fire feature
www.montigo.com
Installation Operation & Maintenance Manual
Check local codes and read all instructions
C-View-ST Residential Fireplace
R520-ST
Indoor
R620-ST
Indoor
Warning:
If the information in these instructions is not
followed exactly, a fire or explosion
may result causing property damage, personal injury or death.
R620-PV Single-side Shown
Warning:
WHAT TO DO IF YOU SMELL GAS
Improper installation, adjustment, alteration, service or maintenance can cause
injury or property damage. Refer to this manual. For assistance or additional
information consult a qualified installer, service agency or the gas supplier.
Safety Notice:
Glass doors on gas fireplaces are extremely hot while the fireplace is on and remain
hot even after the fireplace has been turned off. Safety screens are available and
can reduce the risks of severe burns. Please keep children away from the fireplace
at all times.
For Your Safety:
Do not store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
®
XG0773
C
US
Canadian Heating Products Inc. Langley, BC V4W 4A
•
•
Do not try to light any appliance.
Do not touch any electrical
switch; do not use any phone in
your building.
• Immediately call your gas
supplier from a neighbor's
phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas
supplier, call the fire department.
Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
• Installer: Leave this manual
with the appliance.
• Consumer: Retain this
manual for future reference.
Montigo Del Ray Corp. Ferndale, WA 98248
032211
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Warning:
Read this manual before installing, operating or troubleshooting this appliance.
Please retain this owner's manual for future reference.
Table of Contents
Congratulations
Section 4: Wiring.................................................................... 17
Safety Alert Key
Introduction................................................................................ 3
Main Wiring Schematic........................................ 18
Installation
Conduit & Wire clearances................................... 18
Before you Start.............................................................. 4
Section 5: Installing the Gas Line........................................... 19
Pre-Installation Checklist................................................ 4
Understanding the Basic Operation of the fireplace....... 4
Section 6: Finishing................................................................ 20
Models............................................................................ 3
Section 1: Installation Overview and Product Dimensions....... 5
▪ Section 1-1-1: Clearances........................................... 5
Section 2: Framing the Fireplace.........................................6 - 8
Section 3: The R-View-ST Power Vent System.................9 - 19
Section 3-1: Installing the EPVRR Power Vent.............. 9
▪ Section 3-1-1: Venting Layout....................................... 9
▪ Vertical Vent
Typical Vertical Vent...............................................9
Multi-Elbow Vertical Vent.......................................9
Downward Vertical Vent.........................................9
▪ Section 3-1-2: Venting Components............................ 10
▪ Section 3-1-3: Installation of the EPVRR...............10 - 12
Section 3-2: Installing the EPVRW Vent...................... 13
▪ Section 3-2-1: Venting Layout..................................... 13
▪ Horizontal Vent
Typical Horizontal Vent.........................................13
Multi-Elbow Horizontal Vent.................................13
Downward Horizontal Vent..................................13
▪ Section 3-2-2: Venting Components............................ 14
▪ Section 3-2-3: Installation of the EPVRW..............14 - 16
Page 2
Fireplace A/C...................................................... 17
Remote Switch . ................................................. 17
Section 7: Installing and Removing the Door......................... 21
Section 8: Installing the Firestones......................................... 22
Section 9: Operation
Start-up Sequence................................................. 22
Honeywell HSI Ignition System. .............................. 23
Start-up Sequence SIT-IPI Gas valve....................... 24
Maintenance . ..................................................................25 - 26
General................................................................ 25
Cleaning............................................................... 25
Gas control valve Honeywell HSI. ........................... 25
Troubleshooting.................................................... 26
Honeywell HSI Gas Control Valve................... 26
SIT- IPI Electronic Gas Control Valve.............. 26
Appendix
A. Power Vent Locations. ..................................27 - 28
EPVRR Vertical Power Vent...................................28
EPVRW Horizontal Power Vent..............................28
B. Warranty............................................................. 29
C. State of Massachusetts........................................ 30
Part No. XG0773 - 032211
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Introduction
Safety Alert Key:
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE: Used to address practices not related to personal injury.
• Important: Used to address practices not related to personal injury.
INTRODUCTION
Congratulations on your purchase of a Montigo Fireplace.
With over 30 years of experience, Montigo is committed to providing you
with a gas fireplace that is not only a beautiful addition to your space, but
that is also designed and manufactured to the highest safety, reliability
and engineering standards.
We strongly encourage you to read and carefully follow the instructions
laid out in this Installation, Operation and Maintenance Manual and retain
it for your future reference. Pay special attention to all cautions, warnings,
and notices throughout this manual intended to ensure your safety.
Warranty and Installation Information: (See Appendix B)
The Montigo warranty will be voided by, and Montigo disclaims any
responsibility for, the following actions:
► Modification of the fireplace and/or components including DirectVent assembly or glass doors.
►
Use of any component part not manufactured or approved by
Montigo in combination with this Montigo fireplace system.
►
Installation other than as instructed in this manual.
Consult your local Gas Inspection Branch on installation requirements
for factory-built gas fireplaces. Installation & repairs should be done by
a qualified contractor.
This manual covers installation, operation and maintenance. Lighting,
operation and care of this fireplace can be easily performed by the
homeowner. All installation and service work should be performed by a
qualified or licensed installer, plumber or gasfitter as certified by the state,
province, region or governing body where the fireplace is being installed.
This installation, operation and maintenance manual is applicable to
the model described below. Refer to your model nameplate to verify
included options.
Model: R520-ST
Gas Type: Natural Gas
Gas Rating: 80,000 BTU/H (23.4 Kilowatts) Input
Venting Type: Top dedicated power vent
Burner Type: Contemporary linear burner
Ignition Type:
Honeywell Electronic (HSI)
SIT Electronic Ignition (IPI)
Model: R620-ST
WARNING
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS UNTIL
COOLED.
NEVER ALLOW CHILDREN TO
TOUCH GLASS.
Gas Type: Natural Gas
Gas Rating: 100,000 BTU/H (29.3 Kilowatts) Input
Venting Type: Top dedicated power vent
Burner Type: Contemporary linear burner
Ignition Type:
Honeywell Electronic (HSI)
SIT Electronic Ignition (IPI)
Part No. XG0773 - 032211
Page 3
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Installation
IMPORTANT MESSAGE: SAVE THESE INSTRUCTIONS
The C-View Residential R520-ST & R620-ST Power Vent
fireplaces must be installed in accordance with these Instructions.
Carefully read all the Instructions in this manual first. Consult the
Local Gas Branch to determine the need for a permit prior to starting
the installation. It is the responsibility of the installer to ensure
this fireplace is installed in compliance with the manufacturers
instructions and all applicable codes.
BEFORE YOU START:
INSTALLATION AND REPAIRS SHOULD BE DONE
BY AN AUTHORIZED SERVICE TECHNICIAN. THE
APPLIANCE SHOULD BE INSPECTED BEFORE USE
AND AT LEAST ANNUALLY BY A PROFESSIONAL
SERVICE TECHNICIAN. MORE FREQUENT CLEANING
MAY BE REQUIRED DUE TO EXCESSIVE LINT
FROM CARPETING, BEDDING MATERIAL, ETC. IT
IS IMPERATIVE THAT CONTROL COMPARTMENTS,
BURNERS AND CIRCULATING AIR PASSAGEWAYS
OF THE FIREPLACE ARE KEPT CLEAN.
CAUTION!
Due to its high operating temperatures, the appliance should
be located out of traffic & away from furniture and draperies.
 Children and adults should be alerted to the hazards
of the high surface temperature, which could cause
burns or clothing ignition.
 Young children should be carefully supervised when
they are in the same room as the appliance.
 Clothing or other flammable materials should not be
placed on or near the appliance.
WARNING!
When this appliance is installed directly on any combustible
material other than wood flooring, it must be installed on a
metal or wood panel extending the full width and depth of
the appliance.
Page 4
Installation Checklist
„„ Determine the desired install location of your fireplace
„„ See Section 1, Dimensions on Page 5, and refer to the Framing
Section 2 for details
„„ Select your type and location of your Power Vent : Roof Mounted
(EPVRR) or Wall Mounted (EPVRW)
„„ Lay out the Vent run; calculating the required elbows and straight
runs of 5"/10" flex or rigid pipe
„„ Your termination location should be selected to provide the
shortest possible vent run
„„ Refer to the Section 3, Installing the Power Vent for details
„„ The electrical panel is located on the lower right side when
facing the fireplace
„„ Montigo supplies 20' of low voltage wire, which can be spliced to
any length. This wire CANNOT run in conduit with any other wire
„„ Refer to Section 4, Wiring for Details
„„ The gas connection is located on the lower end when facing
the fireplace
„„ Refer to local codes and guidelines for installation requirements
„„ Installation and repairs should be done by a qualified
contractor and must conform to:
• Installations in Canada must conform to the current
CAN/CGA B-149.1 and .2 Gas Installation Code and local regulations.
• Installations in the USA must conform to local codes,
or in the absence of local codes to the National Fuel Gas Code, ANSI
Z223.1-1988.
• See Appendix C for installation within the State of
Massachusetts. This fireplace must comply with NFPA-54 Chapter
10.
„„ Refer to Section 5, Installing the Gas Line for Details.
Understanding the Basic Operation of the
Residential R520-ST & R620-ST fireplace
The control compartment of this fireplace is located in the bottom of
the fireplace right below the burner system. All models will be supplied with a Honeywell smart valve gas control and will not have a
variable flame control. There are two air switches that are controlling
the gas control system, and are located in the bottom of this fireplace.
These gas valves, and pressure switches communicate with the
electrical control panel via a six conductor cable supplied with the
fireplace.
To operate the fireplace, Montigo has supplied and installed twenty
feet of low voltage wire to this electrical control panel. Connect the
two wire harness to a standard single pole ON/Off switch located at
a location of your choice. You may also extent these wires to any
length, as long as you select a wire of equal quality.
Part No. XG0773 - 032211
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Installation
Section 1: Installation Overview and Product Dimensions
Please review the Pre-Installation Checklist on Page 4 for general information on preparing for a successful installation of your fireplace.
The C-View Residential R520-ST & R620-ST fireplaces may be installed in any location that maintains proper clearances to air conditioning
ducts, electrical wiring and plumbing. Safety, as well as efficiency of operation, must be considered when selecting the fireplace location. Try to
select a location that does not interfere with room traffic, has adequate ventilation, and offers an accessible pathway for Power Vent installation.
The fireplace dimensions are shown below:
I
CL
H
CL
Top View
F
K
O
P
A (Width)
J
G
(Overall
Height)
N
D
(Opening)
B
(Height)
M
C
L
E (Opening)
Front View
A
R520
R620
B
C
D
E
RH-Side View
F
G
H
74 3/4 45 1/4 151/8 18 1/8 61 1/4 233/4 47 7/8 10
86 3/4 45 1/4 151/8 18 1/8 73 1/4 23 3/4 47 7/8 10
I
J
K
5
5
12
2 5/8
12
2 5/8
L
M
N
5 7/8 13 5/8 213/4
5 7/8 13 5/8 21 3/4
O
P
15 1/8
15 1/8
4⅞"
4⅞"
Figure 1. Fireplace dimensions.
Section 1-1-1: Clearances
To ensure the C-View Residential R520-ST and R620-ST Fireplaces
operate safely, all models must maintain the following clearances.
Top - Top Vent
Sides
Floor
Mantel * *
R520-ST
26”
3”
0"
6"
R620-ST
26”
3”
0"
6"
** See Section 6: Finishing for details
Unprotected combustible walls which are perpendicular to the fireplace
opening, must not be closer to the fireplace than the required 6" clearance.
Part No. XG0773 - 032211
WARNING!
The C-View Residential R520-ST & R620-ST are power vented fireplace
systems. Under no circumstances can these model be installed without a
power vent module.
For regular Horizontal vent installation use 5"/10" model EPVRW with the
rough-in kit, EPVRWF for the R520-ST & R620-ST.
For regular Vertical vent installation use 5"/8" model EPVRR with the
rough-in kit, EPVRRF for the R520-ST & R620-ST.
Page 5
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Installation
Section 2: Framing
Step 1. You will need to construct a platform in the framing for the fireplace to sit on. To determine how high to build the platform you must
determine the how high you would like the bottom edge of your glass viewing area to be. The bottom edge of the glass sits 15 1/8" above the
top of the platform. Please note: The top of the platform may not exceed 24" in a room with 8' ceilings.
Q (Opening) both sides typical
U
Framing Dimensions
Model#
Q
R
U
R-Series R520 80¾" 50" 23¾"
R (Opening)
both sides typical
R-Series R620 92¾" 50" 23¾"
3/4”
Plywood
Platform
Max Platform
Ht.
Ceiling
Ht
24"
8'
48"
10'
Figure 2. Fireplace installation, (Rough Frame-In dimensions) Both Sides are Typical.
Step 2. Once the fireplace is placed on the platform, ensure there is access to install the vent pipe, and inline power vent module if applicable
and the gas line. Note the gas line connection location and room to provide a gas service shut-off valve; according to local gas codes. Before
fastening in place line up the front face and rear face of the fireplace (top and botttom), Figure 2a. then secure in place with 1/4" wood screws.
Intake / Exhaust
Venting
1/2”
Both
Sides
Typ
Supply Gas
connection
Figure 2a. Fireplace installation, (Inlet Gas & Power Vent) .
Step 3. Back-framing the Fireplace (Typical Both sides).
Back -frame in the fireplace using typical framing practice, see Figure 2b on both sides and meeting clearance requirements shown on page
5. Install the non-combustible headers supplied by Montigo above the fireplace on both sides as required to attach facing. For cleanest finish
ensure that the facing material is installed flush to the glass viewing area.
Page 6
Part No. XG0773 - 032211
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Installation
NOTE: Remember, both sides of the Fireplace require the same quantities of wood, drywall and hardware.
Cut the Upper and Lower Horizontal 2 x 4's as shown in Figure 2b. Next, cut the Required quantity of short filler 2x4's under the lower Horizontal. Follow Typical building codes and practices when spacing. Next, cut the Required Left and Right Vertical 2 x 4's as shown in Figure 2b.
Lastly, install the Two (2) Supplied Steel Headers above the fireplace throat positioned to attach facing material.
NOTE: When this assembly is in place, ensure ALL the required clearances to combustibles are maintained.
Non-Combustible h eader
(supplied by Montigo)
(vertical)
use Typical
building
practices
when
spacing.
2 x 4, (Top
horizontal)
Distance between 2 x 4's
R520 = 71½"
R620 = 83½"
2 x 4, (Bottom 2-pcs 2 x 4 (vertical)
Both Sides Typ
horizontal)
RHS 102
1” clearance
1” clearance
Both
Sides
Typ
Figure 2b. Fireplace installation, Both Sides are Typical.
Step 4. Installation of the RHS 102 heat shield
When the vent passes through the first adjacent ceiling (or wall for horizontal runs) a Montigo RHS102 heat shield must be installed around the
pipe as shown above.
See the detail of the RHS 102 on the following page.
Part No. XG0773 - 032211
Page 7
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Installation
Figure 2c. Montigo supplied RHS 102 required as venting
passes through the first adjacent ceiling or wall for horizontal
vent runs
Page 8
Part No. XG0773 - 032211
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Installation
Section 3: Installing the Power Vent
Montigo supplies a variety of power venting options. The
location of the power vent should be selected and laid out to provide
the shortest possible run to an external wall or through the roof.
Multi-Elbow Installations
Multi-elbow installations are possible up to a maximum of six 90°
elbows.
,
Section 3-1: Installing a Roof Mounted Vertical Exterior Power
Vent (EPVRR)
This section applies to installations where the shortest possible vent
run is through the roof. Refer to Appendix A - Power Vent locations,
to ensure the planned Power vent location is acceptable. Once the
vent location has been established, please refer to the appropriate
section below for installation details.
V3
Elbow 4
Elbow 5
H2
V2
Section 3-1-1: Venting Layout
Selection of components and details of venting lay out should
adhere to the following guidelines:
Elbow 2
Elbow 3
H1
„„ Ensure there is a minimum run of 2’ of straight pipe before the
power vent.
V1
Elbow 1
„„ Ensure the maximum vent run does not exceed 80’.
„„ Ensure the number of 90° elbows does not exceed 6.
„„ Ensure the number of 45° elbows does not exceed 12.
Max V1 + H1 + V2 + H2 + V3
Max Elbows
100’ feet
six 90
Figure 3a. Multi-elbow Venting Installations.
Max V
120’ feet
Max Elbows
N/A
Downward Vertical Venting
Note: The downward vent run must not exceed 6' of vent run.
Figure 3. Typical straight Venting Installations.
V3
Elbow 3
Elbow 2
H1
D = 6’ foot
MAX
V1
Elbow 1
Elbow
Elbow 4
H2
Max V1 + H1 + D + H2 + V3
Max Elbows
40’ feet
six 90
Figure 3b. Downward Venting Installations.
Part No. XG0773 - 032211
Page 9
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Installation
Section 3-1-2: Venting Components
The following venting components and associated Montigo part
numbers are available for the EPVRR:
A - Termination
EPVRR
B - Rough-in Frame
EPVRRF
RFL-1 (12" Section)
RFL-2 (24" Section)
RFL-3 (36" Section)
RFL-4 (48" Section)
C - Flex Sections
D - Rigid Sections
Section 3-1-3: Installation of the EPVRR external roof
mounted power vent module. Refer to Appendix A - Power
Vent locations, to ensure the planned Vertical Power vent location is
acceptable.
The EPVRR Power Vent dimensions:
Ø14”
REXT - 1 (12" m/f Section)
RXT-20 (20" section)
REXT - 2 (24" m/f Section)
REXT - 3 (36" m/f Section)
REXT - 4 (48" m/f Section)
E - Elbows
REL-90MM (m/m 90° Elbow)
REL-90FF (f/f 90° Elbow)
REL-90FM (f/m 90° Elbow)
REL-45FM (f/m 45° Elbow)
F - Power Cord
Harnesses:
EPVH10 -10 foot power cord and harness
EPVH20 -20 foot power cord and harness
EPVH30 -30 foot power cord and harness
EPVH40 -40 foot power cord and harness
EPVH50 -50 foot power cord and harness
EPVH60 -60 foot power cord and harness
EPVH70 -70 foot power cord and harness
EPVH80 -80 foot power cord and harness
EPVH90 -90 foot power cord and harness
EPVH100 -100 foot power cord and harness
19 1/4”
2”
8 1/2”
Ø 1/2”
Front View
18”
18”
Connection and installation of the vent components
should adhere to the following guidelines:
„„ Connect all vent sections using a minimum of three sheet
metal screws on the outer pipe flue.
„„ Ensure the pipe ends male to female slide in a minimum of
1 1/2“ of overlap.
Top View
The EPVRRF Rough-in Frame dimensions:
6”
„„ Ensure all runs are supported with a minimum of 3 supports
per 10’ of venting.
„„ When hanging/ supporting venting, ensure that 1” clearance
is maintained on all sides to any combustible material.
Ø 8”
14”
„„ Ensure when cutting sections of rigid pipe to maintain integrity
of internal supports.
Front View
„„ Place the springs, supplied with the pipe kit, between the
outer and inner pipes to keep the pipes separate and avoid
any possible hot spots.
„„ Montigo recommends the use of a flex section for the final pipe
connected directly to the fireplace offering greater flexibility of
installation and absorption of movement.
18”
18”
„„ All exterior joints in venting should be sealed with high heat
silicone RV230.
Top View
Page 10
Part No. XG0773 - 032211
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Installation
Installing the external roof mounted power vent module
Step 1.Construct a Vertical Chase for the termination opening to
meet the following requirements:
Step 3.
Install the Power Vent Rough-in Kit. Pull wire harness through
the supplied hole in the bottom corner of the rough-in box, and
snap into the slot provided, (See figure 4b inset).
■ Opening Size must be: 14 1/2" x 14 1/2" x 18" Min. height.
14 1/2"
1/2”
14
14
141/2”
1/2"
Power Vent
Rough-in Kit
Electrical Harness
Connector Location
18”
18"
Inset
Electrical Harness
Figure 4. Contruction, Rough-in framing.
Step 2.
Install the Vent pipe female end up, and 2" to 3" MAX. from
the top of the Constructed Chase. Also, at this point install the
Electrical harness, (EPVH-(10-100) that will communicate with
the Power Vent Module.
Figure 4b. Installation of Rough-in Kit
Step 4.
Install fasteners around perimeter of Rough-in Kit. (Holes supplied for ease of installation)
Electrical Harness
with Connection
2 to 3” MAX
Vent Pipe
Install Fasteners around
perimeter of Rough-in Kit
Vent Chase
Figure 4c. (Fasten Rough-in Kit to framing)
Figure 4a. Installation, Vertical Vent pipe. (female end top end).
WARNING!
All venting material must be sealed with high heat silicone sealant
RV230. All venting material to be Montigo flex pipe, with as few
joints as possible. All joints use MVA vent splice, sealed thoroughly
with silicone.
WARNING!
Montigo will not be held responsible for any water damage
that may occur from not installing the equipment as specified
by this document.
Part No. XG0773 - 032211
Figure 4d. (Installed Stainless steel cover)
Page 11
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Installation
Step 5.
Install the Power Vent, Roof-top Stainless steel cover over the
Installed Rough-in Kit. (You can see the Electrical harness connector in the top right corner).
Electrical Harness
from Power Vent
Stainless Steel
Fasteners
Figure 4e.
Figure 4f.
Step 6.
Install the Power Vent Module Power / communication harness.
Hold the Power Vent in close proximity of the assembled Chase,
(with stainless steel cover attached) and plug in the Power Vent
communication / Power Cord. (Note the direction and orientation of the plug socket). (See Figure 4e & Figure 4f)
Install Power Vent Module
with Power / Communication
Harness
Vertical Roof Top
Power Vent
Vertical Roof Top
Power Vent Rough-in
Kit
Figure 4h. (Installed Power Vent Module)
Step 8.
Install (3) three stainless steel fasteners around Power Vent
Module @120 degrees (penetrating through the inner stainless
steel vent cover)
CAUTION!
 Vent terminations can be very hot. The termination is to be
installed higher than 7 feet above a public walkway.
 Do not obstruct, or attempt to conceal, the vent termination.
These actions will affect the operation of the fireplace, and may be
hazardous.
 In heavy snow areas, take extra care to prevent snow buildup
from obstructing the vent termination.
Figure 4g. (Installation of Power Vent Module)
Step 7.
Install the Power Vent Module. Place the Power Vent Module
over the stainless steel cover flange and vent pipe, aligning the
Power Vent into final position. Ensure the Harness is placed
down in the Rough-in box when placing the Power Vent Module
into place. The Power Vent Module will sit flush with the stainless
steel cover if installed correctly.
Page 12
Part No. XG0773 - 032211
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Installation
Section 3-2: Installing a Wall Mounted Vertical Exterior Power
Vent (EPVRW)
This section applies to installations where the shortest possible
vent run is through an exterior wall. Refer to Appendix A - Power
Vent locations, to ensure the planned Power vent location is acceptable. Once the vent location has been established, please refer to the
appropriate section below for installation details.
Multi-Elbow Installations
Multi-elbow installations are possible up to a maximum of six 90°
elbows.
Elbow 6
Elbow 4
Section 3-2-1: Venting Layout
Selection of components and details of venting lay out
should adhere to the following guidelines:
Elbow 5
H2
V2
„„ Ensure there is a minimum run of 2’ of straight pipe before the
power vent.
Elbow 2
Elbow 3
„„ Ensure the maximum vent run does not exceed 100’.
„„ Ensure the number of 90° elbows does not exceed 6.
„„ Ensure the number of 45° elbows does not exceed 12.
H3
V3
H1
V1
Elbow 1
H
Max V1 + H1 + V2 + H2 + V3 + H3
V
Max Elbows
100’ feet
six 90
Figure 5a. Multi-elbow Venting Installations.
Downward Vertical Venting
Max V + H
100’f eet
Max Elbows
Note: The downward vent run must not exceed 6' of vent run.
H1
six 90
Figure 5. Typical Venting Installations.
WARNING!
All venting material must be sealed with high heat silicone sealant
RV230. All venting material to be Montigo flex pipe, with as few
joints as possible. All joints use MVA vent splice, sealed thoroughly
with silicone.
V
D
H2
WARNING!
Montigo will not be held responsible for any water damage
that may occur from not installing the equipment as specified
by this document.
Max V1 + H1 + D + H2
Max Elbows
40’ feet
six 90
Figure 5b. Downward Venting Installations.
Part No. XG0773 - 032211
Page 13
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Installation
Section 3-2-2: Venting Components
The following venting components and associated Montigo
part numbers are available for the EPVRW:
A - Termination
EPVRW
B - Rough-in Frame
EPVRWF
RFL-1 (12" Section)
RFL-2 (24" Section)
RFL-3 (36" Section)
RFL-4 (48" Section)
C - Flex Sections
D - Rigid Sections
REXT - 1 (12" m/f Section)
RXT-20 (20" section)
REXT - 2 (24" m/f Section)
REXT - 3 (36" m/f Section)
REXT - 4 (48" m/f Section)
E - Elbows
REL-90MM (m/m 90° Elbow)
REL-90FF (f/f 90° Elbow)
REL-90FM (f/m 90° Elbow)
REL-45FM (f/m 45° Elbow)
F - Power Cord
Harnesses:
Section 3-2-3: Installation of the EPVRW external wall
mounted power vent module. Refer to Appendix A - Power
Vent locations, to ensure the planned Vertical Power vent location is
acceptable.
The EPVRW Power Vent dimensions:
16 3/4”
14 1/8”
14 3/4”
Side View
EPVH10 -10 foot power cord and harness
EPVH20 -20 foot power cord and harness
EPVH30 -30 foot power cord and harness
EPVH40 -40 foot power cord and harness
EPVH50 -50 foot power cord and harness
EPVH60 -60 foot power cord and harness
EPVH70 -70 foot power cord and harness
EPVH80 -80 foot power cord and harness
EPVH90 -90 foot power cord and harness
EPVH100 -100 foot power cord and harness
Connection and installation of the vent components
should adhere to the following guidelines:
„„ Connect all vent sections using a minimum of three sheet
metal screws on the outer pipe flue.
„„ Ensure the pipe ends male to female slide in a minimum of
1 1/2“ of overlap.
Ø
Ø 5.0"
5”
15 5/8”
14 1/8”
Front View
The EPVRWF Rough-in Frame dimensions:
4 5/8"
3”
Ø 8”
„„ Ensure all runs are supported with a minimum of 3 supports
per 10’ of venting.
14”
Front View
„„ When hanging/ supporting venting, ensure that 1” clearance
is maintained on all sides to any combustible material.
18 3/4"
„„ Ensure when cutting sections of rigid pipe to maintain integrity
of internal supports.
„„ Place the springs, supplied with the pipe kit, between the
outer and inner pipes to keep the pipes separate and avoid
any possible hot spots.
18 3/4"
„„ Montigo recommends the use of a flex section for the final pipe
connected directly to the fireplace offering greater flexibility
of installation and absorption of movement.
„„ All exterior joints in venting should be sealed with high heat
silicone RV230.
Page 14
Top View
Part No. XG0773 - 032211
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Installation
Installing the external wall mounted power vent module
Step 4.
Insert the conduit from the Power Vent Module into the rough-in
frame through the two top right entry holes. Remove the nut from
the supplied strain relief and place as shown, Figure 6c.
Step 1.Construct a frame for the termination opening to meet the
following requirements:
■ Opening Size must be: 14 1/2" x 14 1/2".
Strain Relief
14 1/2”
(Opening)
Power Vent Conduit
Strain Relief
Nut
14 1/2”
(Opening)
Figure 6. Framing the Opening for Power Vent
Figure 6c. Installation of Power Vent Conduit
Step 2.
Step 5.
Insert the Power Vent Rough-in Box as shown in Figure 6a.
Fasten the Box securely in place with Screws or nails, Figure
6a. Apply exterior sheathing and finishing if required.
Securely fasten bottom Collar pan into the Rough-in frame using
the existing hardware, (4-pcs). Tighten Strain Relief nut onto
Strain relief.
Step 6.
Framing
Fasteners
Pull Power Vent Connector, (from behind) half-way through
supplied hole in conduit mounting frame, and snap into place,
(notches in two plastic wing clips. Orientation not critical).
Strain Relief & tightened nut
Power Vent Conduit
Rough-in Frame
Conduit
mounting
frame
Power Vent
Connector
Figure 6a. Orientation, Placing the Power Vent Inner Box
Step 3.
Next, remove the bottom collar and conduit mounting frame as
shown Figure 6b. (Place removed hardware in a handy location
for re-assembly).
Tightened hardware, 4-pcs.
Figure 6d. (Installing Conduit connector & conduit mounting frame)
Step 7.
Fasten Conduit mounting frame into place using existing hardware, (6-pcs). (Coil conduit in behind cover.)
Figure 6b. Installation of Rough-in Kit
Part No. XG0773 - 032211
Page 15
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Installation
CAUTION!
 Vent terminations can be very hot. The termination is to be
installed higher than 7 feet above a public walkway.
Installed Power Vent
Connector
 Do not obstruct, or attempt to conceal, the vent termination.
These actions will affect the operation of the fireplace, and may be
hazardous.
Tightened hardware, 6-pcs.
 In heavy snow areas, take extra care to prevent snow buildup
from obstructing the vent termination.
Figure 6e. (Assembled Rough-in Kit)
Step 8.
Install the Power Vent Power / communication harness. Hold the
Power Vent in close proximity of the assembled Rough-in Kit,
and plug in the Power Vent communication / Power Cord. (Note
the direction and orientation of the pins inside the Power Vent
connector, snap together). (Figure 6f).
Communication
Harness.
TOP of Power Vent,
(Note Quantity of
louvers).
Note louver
direction
Figure 6f. (Installation of Power Vent communication harness)
Step 9.
Install the Power Vent. Place the Power Vent into the Rough-in
frame, aligning the Power Vent into final position. Ensure the
Harness is placed down in the Rough-in box when placing the
Power Vent. (Secure the Power Vent in Place with the supplied
hardware).
Tightened hardware,
4-pcs.
Figure 6g. (Completed Installation of Power Vent)
Page 16
Part No. XG0773 - 032211
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Installation
Section 4: Wiring
Installation Of Electrical Supply
The C-View Residential R520-ST & R620-ST Fireplaces are supplied with an external electrical Control Panel pre-wired by the factory.
The power control box is connected to the fireplace with a 20 foot
long 6 conductor cable that will communicate with the fireplace.The
control panel should be located in a location that would be accessible
when the fireplace in finished.
Wall Switch
110V Power Supply
Fuse
LED Indicator
6 - conductor
communication
cable
Power Vent
Speed Control
Left-sideView
Power Vent
Speed Control
Right-sideView
Figure 10. C-View Residential Power Vent Module
Installing The Remote Switch
The C-View Residential R520-ST & R620-ST Fireplaces may be
connected to a wall switch or a hand-held remote. The valve operates on a 24V circuit. DO NOT connect the gas valve to an external
circuit.
Figure 8. (Fireplace to Control Panel Harness)
The power cord from the power vent module pugs into the side of this
panel. A 20 foot low voltage wire is attached and connected to this
panel as well. Connect a single pole On/Off switch (Black and White)
to these two wires at a location of your choice, (See Installing the
Remote Switch).
Installations in Canada must be electrically grounded in accordance
with CSA C22.1 Canadian Electrical Code Part 1 and/or Local Codes.
Installations in the USA must be electrically grounded in accordance with local codes or, in the absence of local codes, with the
National Electrical Code, ANSI/NFPA 70-1987.
Wall Switch
Figure 11. (Remote Switch Wire connection)
The external electrical panel supplied with the fireplace is equipped
with a 20 foot low voltage wire, for connecting to a wall switch of your
choice. Should you require a longer switch wire, replace this wire to
any length with a wire of equal quality. Additional length are available
upon request.
CAUTION!
Power Vent
Motor
Pre-purge
Module
Indicator
light
Post-purge
Module
Fuse
Wall
Switch
Gas Control
Wiring & Air
Proving
Switch
Part No. XG0773 - 032211
After this Time-On Delay the fireplace will proceed with the Initiated Start-Up Sequence has completed.
Vent Speed
Control
110V Power
Supply
Figure 9. (Control Panel Overview)
The valve has a 1/2 minute Time-On Delay to clear All possible
build up of burned gas within the System.
Ignitor
operation
Lights
Terminal Block
Page 17
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Installation
If you do not follow these instructions exactly, a fire or
explosion may result causing property damage, personal injury or loss of life.
WARNING!
NC
Gas
Valve 1
LV Wall
Switch
7
8
Gnd
Green
6
Brn
5
Blu
4
Red
3
Blk / Wht
2
Wht / Blk
Wht / Blk
1
Blk / Wht
Pre-purge
Time-On delay
Post-purge Module
NO
Combustion Flue Gas
Air Switch Switch
Fireplace
Figure 12. C-View Residential R520-ST & R620-ST Wiring Schematic
Conduit & Wiring clearances
Connect the wiring to the fireplace as outlined in the C-View Residential R520-ST & R620-ST schematic, figure 12. Connect the
wiring to the Linear power vent as outlined in the previous section.
Ensure that the proper clearances are maintained for the wiring and
conduit. When installing the wiring it must never run above the vent
run and it must be at least 1" clear of all venting.
1” Clearance
Figure 12b. Conduit and Wiring Clearances.
Page 18
Part No. XG0773 - 032211
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Installation
Section 5: Installing the Gas line
Section 5-1: FUEL CONVERSION
„„ Verify that your fireplace is compatible with your available gas
type. (Natural Gas or Propane shown by "N" or "L" in your
model number
„„ If gas type is not compatible, contact your local Montigo
representative to purchase a conversion kit.
„„ Conversion kits must be installed by a qualified service technician.
After gas line is connected, each appliance connection,
valve and valve train must be checked while under normal
operating pressure with either a liquid solution, or leak
detection device, to locate any source of leak. Tighten any
areas where bubbling appears or leak is detected until
bubbling stops completely or leak is no longer detected.
DO NOT use a flame of any kind to test for leaks.
WARNING!
Section 5-2: GAS PRESSURE
„„ Optimum appliance performance requires proper input pressures.
„„ Gas line sizing requirements will be determined in ANSI Z221.3
National Fuel Gas Code in the USA and CAN/CGA B149 in
Canada.
Gas Pressure
Minimum inlet pressure
Manifold pressure
Note:
Natural Gas
Propane
5.5in. w.c.
3.5in. w.c.
11in. w.c.
10in. w.c.
When pressure testing the fireplace, Gas line, and input system
follow the appropriate local codes or your area. DO NOT
connect the fireplace to pressures in excess of 1/2lb. This will
damage the gas control valve.
„„ The manifold outlet pressure is set from the factory to the
appropriate pressure but should be verified.
„„ To check pressures, control valves have a provision to remove
a 1/8” N.PT. plug to be fitted with a hose barb.
„„ Montigo requires a service shut off valve be located in an
accessible location to isolate the gas supply.
„„ Only install gas shut-off valves approved for use by the state,
province, or other governing body in which the fireplace is being
installed.
Section 5-3: GAS CONNECTION
„„ See Figure 14 below for location of gas line access.
„„ Flexible gas connectors must not exceed 3 feet in length, unless
allowable within local regulations.
„„ Connect incoming gas line to the 1/2"or 3/8" gas inlet port.
„„ Purge all air out of gas line.
„„ Check appliance connection, valve and valve train under normal
operating pressure with a commercially available leak check
solution.
„„ DO NOT USE A FLAME OF ANY KIND TO TEST FOR LEAKS.
3”
3”
1/2” gas
inlet
Figure 14. Gas Inlet Supply location, (Right-hand side of fireplace).
Part No. XG0773 - 032211
Page 19
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Installation
Section 6: Finishing
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Combustible
facing material
Start of combustible
framing
Combustible
construction allowed
in shaded area
Top of
fireplace
Non-combustible
headers supplied by
Montigo (may be
placed where required
for fastening facing)
12 11 10 9 8 7 6 5 4 3 2 1
Glass
Figure 16. Combustible mantles and facings. (Not to scale)
Fireplace Facing
When selecting the finish material for your fireplace, it is important to
remember the following:
If the surround of the fireplace is to be painted to match the room decor,
heat-resistant paint must be provided . Also, decorative facing must not
extend past the fireplace opening at all, because it will interfere with the
access to retainers for removal of glass door and access to the lower
compartment.
Mantels & Surrounds
NOTE: National Canadian Gas Association mantel test requirements
are for fire hazard prevention to combustible materials.
Please be aware; temperatures over the mantel will rise above normal
room temperature and walls above fireplace may be hot to touch.
Warning:
We recommend careful consideration be given to the effects of elevated
mantel temperatures which may be in excess of product design, for
example: candles, plastic or pictures. This can cause melting, deformation,
discoloration or premature failure of T.V. and radio components.
WARNING!
We recommend careful consideration be given to the effects of
elevated mantel temperatures which may be in excess of product
design, for example: candles, plastic or pictures. This can cause
melting, deformation, discoloration or premature failure of T.V.
radio, and other electronic components.
Page 20
WARNING!
When covering the upper metal portion of the fireplace, (as
shown, Fig.16) with a non-combustible material, Please Note:
The decorative facing materials may be subject to temperatures
in excess of 250° F. This should be considered when selecting
facing materials.
Part No. XG0773 - 032211
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Installation
Section 7: Removing & Installing the Door
Removing the doors:
The doors are removed in a few simple steps.
Follow the steps below to remove the Vertical Door trim, place the
Door removal tool, and then remove the door. Replace all the parts in
reverse order.
Step 3. Hold the Glass Removal Tools firmly, Lift the door upward,
into the top door frame, Figure 17c. Then pull the bottom of the glass
door downward, and tilt outward from the bottom fireplace door frame.
Figure 17d. NOTE: Read ALL the instruction supplied with the
tool, and follow the associated operating procedures.
Step 1. Remove the two (2) Vertical Trim pieces, (LH & RH). Pulling
firmly with your fingers, remove from the bottom then the top. (See
Figures 17 & 17a). Other side Typical.
Lift Upward into
the door frame.
Lift Downward
& away from frame.
Figure 17c. (Lift the door upward) Figure 17d. (Lift the bottom of the
door outward).
Step 4. Still holding the Glass
Removal Tool firmly, remove the door
outward, and away from the Fireplace, Figure 17e.
Step 5. Place the door in a safe
location while maintenance, cleaning
or other operation are in progress.
Figure 17. (Remove LH Trim)
Figure 17a. (Remove RH Trim)
NOTE: Read ALL the instruction
supplied with the tool, and follow
the associated operating procedures.
Step 2. Remove the supplied glass lifting tool from the packaging.
Place in the center of the Glass door as shown, and activate the suction feature of the tool, Figure 17b. NOTE: Read ALL the instruction supplied with the tool, and follow the associated operating
procedures.
Step 6. To replace, See Installing
the Door, Below.
Figure 17e.
Installing the Door:
To install the door, follow Steps 1 and 4 above, (in reverse order).
WARNING!
Do not attempt to clean glass when hot.
Figure 17b. Supplied Glass lifting tools.
Part No. XG0773 - 032211
Do not clean glass with abrasive materials as any glass etching may cause premature glass failure.
Page 21
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Installation
Section 8: Installing the Firestones
The C-View Residential R520-ST & R620-ST fireplace have the
option of installing the supplied glass Firestones or other optional
colored glass media, or cultured rocks.
Note: The designer Firestones or cultured rocks cannot cover
the burners, doing so produces an undesirable / uneven flame
pattern and eventual sooting.
Section 9: Start-up Sequence
WARNING!
If you do not follow these instructions exactly, a fire
or explosion may result causing property damage,
personal injury or loss of life.
Startup Sequence:
Firestones
The C-View Residential R520-ST & R620-ST fireplace are supplied
with a quantity of Glass Firestones. To install the Firestones remove
the Door and trim as shown in the previous Instruction. Follow these
instructions to ensure all parts are removed or replaced as required.
Once the Trim and glass doors are removed place the firestones
randomly around the burners as shown in Figures 19 and 19a.
Note: DO NOT cover the burners with designer Firestones
or Optional Rocks.
A. Purge all air out of the gas supply line to the fireplace system and ensure that the supply pressure is not in excess of
12" WC.
B. Plug the electrical control panel into the power outlet. (The
power vent will start and run for about three minutes and
then turn off.
Caution: Do not turn OFF the power to this panel at this time
to operate the fireplace
1. Turn the speed control on the right side of the panel to a low
positing ( clockwise ).
2. Turn the wall switch to the "On" position. The LED on the
left of the panel should illuminate.
Figure 19. Completed glass Firestone installation. (Note: place glass
Firestones on top of mesh pilot cover to complete the installation.
3. Turn the speed up on the speed control knob very slowly
until the right LED is illuminated. Note: There will be a 1/2
minute Time-On delay, then burner will fire up. This Initial
setting will produce the most attractive looking fire. However, You may increase the speed if desired.
4. If the right LED is not illuminated when the power vent
module is running it will be a signal that the combustion air
supply is inadequate.
Figure 19a. Operating Propane gas fireplace with designer glass
Firestones surrounding burner tray.
Optional River Rocks
The C-View Residential fireplace has the option of installing the cultured rocks which mimic real stone. These may be spaced at random,
or in a visual pattern of your preference. See the Montigo web site for
photographs and ideas.
www.montigo.com
CAUTION!

This fireplace has been set up at the factory for a
determined air volume though the venting system.

This fireplace will not operate unless the correct
air movement is detected by our control system..

Please consulted with your contact person at
Montigo should you have any problems with your start up.
CAUTION!
DO NOT OPERATE THIS FIREPLACE WITHOUT THE GLASS
DOOR OR WITH A BROKEN GLASS DOOR.
Page 22
Part No. XG0773 - 032211
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Operation
with Honeywell Electronic Ignition
For Your Safety - READ BEFORE LIGHTING:
WARNING!
If you do not follow these instructions exactly, a fire or explosion may
result causing property damage, personal injury or loss of life.
A. This appliance is equipped with an ignition system that
lights the pilot burner automatically. Do not attempt to
light the pilot by hand.
B. BEFORE LIGHTING smell all around the appliance area for
gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
What To Do If You Smell Gas:
QQ Do not try to light any appliance.
QQ Do not touch any electrical switch; do not use any
phone in your building.
QQ Immediately call your gas supplier from a neighbour's
phone. Follow the gas supplier's instructions.
QQ If you cannot reach your gas supplier, call the Fire
Department.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by
hand, don't try to repair it, call a qualified service technician.
Force or attempt to repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system,
and any gas control which has been under water.
Lighting Instructions:
1. STOP! Read the safety information above on this label.
2. Lift out the lower Horizontal access panel.
8. If the fireplace does not operate, follow the instructions "To
Turn Off Gas To Appliance" and call your service technician
or gas supplier.
3. Turn switch on the gas control to OFF".
4. Wait 5 minutes to clear out any gas. If you smell gas,
STOP! Follow "B" in the safety information above on this
label. If you don't smell gas, go to the next step.
5. Turn switch on the gas control to "ON". NOTE: This unit is
equipped with an ignition system that lights the pilot burner
automatically. Do not attempt to light the pilot by hand.
Gas
Inlet
Gas Control Switch
Shown in "On" Position
6. Turn on wall switch.
7. Replace the lower Horizontal access panel.
To Turn Off Gas To Appliance:
1. Turn off remote switch.
3. Turn the switch on the gas control to "Off".
2. Lift out the lower Horizontal access panel.
4. Replace the lower Horizontal access panel.
Part No. XG0773 - 032211
Page 23
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Operation
Proflame SIT Electronic Ignition
For Your
Safety
- READ
BEFORE
LIGHTING:
with
American
Flame Electronic
Ignition
WARNING!
If you do not follow these instructions exactly, a fire or explosion may
result causing property damage, personal injury or loss of life.
A. This appliance is equipped with an ignition system that
lights the pilot burner automatically. Do not attempt to light
the pilot by hand.
B. BEFORE LIGHTING smell all around the appliance area for
gas. Be sure to smell next to the floor because some gas is
heavier than air and will settle on the floor.
What To Do If You Smell Gas:
 Do not try to light any appliance.
 Do not touch any electrical switch; do not use any phone
in your building.
 Immediately call your gas supplier from a neighbour's
phone. Follow the gas supplier's instructions.
 If you cannot reach your gas supplier, call the Fire
Department.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by
hand, don't try to repair it, call a qualified service technician.
Force or attempt to repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system,
and any gas control which has been under water.
Lighting Instructions:
1. STOP! Read the safety information above on this label.
2. Remove the lower Horizontal access panel.
3. Turn Incoming gas valve to the ON" position.
4. Wait 5 minutes to clear out any gas. If you smell gas,
STOP! Follow "B" in the safety information above on this
label. If you don't smell gas, go to the next step.
5. Turn wall switch "ON".
two trials, (one minute audible clicking, thirty seconds of
silence, and then another one minute of audible clicking).
7. After completion of the information in the Troubleshooting
section, Repeat step 5.
8. If the system will not function correctly, follow the instructions "To Turn Off Gas To Appliance" and call your service
technician or gas supplier.
6. If the Fireplace does not light, the System will cycle through
EV1 (Pilot
burner)
Pilot Sensor
Lockout Reset Key
Diagnostic Terminal
Igniter
Ground
EV1 (Pilot burner)
EV2 (Main burner)
Power
Gas "In"
EV2 (Main
burner)
Pilot Adjust Screw
Gas "Out"
Incoming Gas
Line, Shut-off
Valve
To fireplace Main
burner
Command (Wall
switch)
To Turn Off Gas To Appliance:
1. Turn off remote switch.
3. Turn the incoming gas control valve to "Off".
2. Remove the lower Horizontal access panel.
4. Replace the lower Horizontal access panel.
Page 24
Part No. XG0773 - 032211
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Maintenance
Gas Control Valve (Honeywell HSI)
Lighting Instructions
See pages 23 and 24.
Honeywell (Q3450)
Pilot Assembly
Pilot Electrical
Harness Connector
Honeywell Gas
Control (SV9501M)
General
 Have the fireplace and installation inspected yearly. The inspection
must include, but is not limited to, the following:
• A visual check of the entire vent system and termination.
• An inspection of the explosion relief flappers and the door
gasketing to ensure a proper seal.
• An inspection of the burner, venturi, and primary air openings.
Gas Control
Connector
R
W
Bk
Figure 20. Honeywell SV9501 gas valve.
• An inspection of the gas valve, gas components, and pilot flame.
For your convenience a 1/8" manifold pressure tap is supplied
on the gas valve for a test gauge connection.
• Ensure proper log placement as per this manual.
• Inspection of all optional equipment; fans, thermostats, etc.
 For Natural Gas this appliance requires a minimum inlet pressure
of 5.5" W.C. and a manifold pressure of 3.5" W.C.
 For Propane Gas this appliance requires a minimum inlet pressure
of 11" W.C. and a manifold pressure of 10" W.C.
 Always keep the fireplace area clear and free of combustible materials,
as well as gasoline and other flammable vapors and liquids.
 Do not use this appliance if any part has been under water. Immediately
call a qualified service technician to inspect the appliance and to
replace any part of the control system and any gas control which
has been under water.
Cleaning
When the fireplace is first activated, there may be some smoking and
a visible film may be left on the glass. This is a normal condition, and is
the result of burning of protective coatings on new metal.
 Glass must be cleaned periodically to remove any film (which is
a normal by-product of combustion) which may be visible. Film
can easily be removed by removing the door, as shown on Page
23. Handle the door carefully, and clean it with non-abrasive glass
cleaners. One of the most effective products is Kel Kem.
 Silicone seals on inner door during initial firing will "off gas", leaving
a visual deposit of a white substance on combustion chamber walls.
This can easily be removed using normal household products.
 Use a vacuum cleaner or whisk broom to keep the control
compartment, burner, and firebox free from dust and lint. Part No. XG0773 - 032211
Page 25
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Maintenance
Troubleshooting: (Honeywell).
Troubleshooting: (SIT - IPI Electronic)
1. Locate the lead to the battery backup, (remove)
(Refer to schematic, below)
2. Locate the AC/DC wall transformer, (Unplug connector)
(Refer to schematic, below)
1.
2.
If your fireplace still does not operate correctly, consult your dealer or
the manufacturer.
If your fireplace still does not operate correctly, consult your dealer or
the manufacturer.
All service and repairs should be performed by a qualified
Technician.
All spare parts, optional fans, and optional trim finishes are available
from your local dealer or the manufacturer.
Page 26
Part No. XG0773 - 032211
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Appendix A - Power Vent Locations
V
Horizontal
Detail
Vertical Detail
A = clearance to the termination frame above grade, veranda, porch, deck, or balcony
[30 inches (75 cm) minimum]
N =
B = clearance to door, or sides and top of window, that may be opened [30 inches (75
cm) minimum for appliances.
P = clearance under veranda, porch, deck, or balcony [30 inches (75 cm) minimum‡ to
non-combustibles] [30 inches (75 cm) minimum‡ to combustibles]
C = clearance to bottom of window that may be opened horizontally [36 inches (92 cm)
minimum for appliances.
Q = clearance above a roof [18 inches (46 cm) minimum]
D = no clearance to permanently closed window when installed with approved glass
penetration termination
S = clearance from corner in recessed location [30 inches (75 cm) minimum]
E = clearance to permanently closed window [30 inches 75 cm recommended to prevent
condensation on window]
F = vertical clearance to ventilated soffit located above the termination within a horizontal
distance of [30 inches 75 cm] from the centreline of the termination [30 inches (75
cm) minimum]
G = clearance to unventilated soffit [30 inches (75 cm) minimum to non-combustibles]
[30 inches (75 cm) minimum to combustibles]
R = clearance to adjacent walls and neighboring buildings [30 inches (75 cm) minimum]
T = maximum depth in recessed location [48 inches (122 cm) minimum]
U = minimum width for back wall of recessed location [60 inches (150 cm) minimum]
V = minimum horizontal clearance between the frames of two terminations that are
level, (see applicable Detail).
W = horizontal clearance between the frames of two terminations that are not level. [30
inches (75 cm) minimum]
a vent shall not terminate directly above a sidewalk or paved driveway which is
located between two single family dwellings and serves both dwellings
only permitted if veranda, porch, deck, or balcony has an open side that is equal
to or greater than the depth of the enclosed area
*
as specified in CGA B149 Installation Codes. Note: local Codes or Regulations may
require different clearance.
†
H = clearance to outside corner [30 inches (75 cm) minimum]
I =
clearance to inside corner [30 inches (75 cm) minimum]
J = * not to be installed above a meter/regulator assembly within
40" (103 cm) horizontally from the centreline of the regulator
K = clearance to service regulator vent outlet [3 feet minimum in the United States] [*6
feet (1.8 m) minimum in Canada]
†
clearance above paved sidewalk or a paved driveway located on public property
[*7 feet (2.1 m) minimum]
‡
L = clearance to non-mechanical air supply inlet to building or the combustion air inlet
to any other appliance [16 inches (41 cm) minimum for appliances ≤100 000 BTU/H
(30kW)]
M = clearance to mechanical air supply inlet [*6 feet (1.8 m) minimum]
Part No. XG0773 - 032211
Page 27
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Appendix A - Power Vent Locations
EPVRR Vertical Power Vent Detail
EPVRW Horizontal Power Vent Detail
Wall
30”Min.
“R”
Eaves / Overhang
Wall
Wall
30”Min.
“R”
“R”
Top View
24” (61cm)
Min. “V”
30”Min.
“H” & “I”
30”Min.
“F” & “G”
30” (75cm)
Min. “V”
Front View
Wall
18”
18”
Min.
Front View
Page 28
Part No. XG0773 - 032211
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Appendix B - Warranty
The Warranty
The Companies warrants the Montigo Gas Appliance to be free from defects in materials and workmanship at the time of manufacture. On the Montigo fireplace,
there is a ten-year warranty on the firebox and its components, a five-year warranty on the main burner and pilot burner, and a one-year warranty on the gas control
valve, fibre logs and Power Vent Module. The Glass, plated / painted finishes, and refractory lining are exempt from the warranty.
Remedy And Exclusions
The coverage of this Warranty is limited to all components of the Gas Appliance manufactured by The Companies.
This Warranty only covers Montigo Gas Appliances installed in the United States or Canada.
If the components of the Gas Appliance covered by this Warranty are found to be defective within the time frame stated (see The Companies right of investigation
outlined below). The Companies will, at its option, replace or repair defective components of the Gas Appliance manufactured by The Companies at no charge,
and will also pay for reasonable labour costs incurred in replacing or repairing components. If repair or replacement is not commercially practical, The Companies
will, at its option, refund the purchase price of the Montigo Gas Appliance.
This Warranty covers only parts and labour as provided above. In no case shall The Companies be responsible for materials, components, or construction which
are not manufactured or supplied by The Companies, or for the labour necessary to install, repair or remove such materials, components or construction. All
replacement or repair components will be shipped F.O.B. the nearest The Companies factory.
Qualifications To The Warranty
The Gas Appliance Warranty outlined above is further subject to the following qualifications:
(1) The Gas Appliance must be installed in accordance with The Companies installation instructions and local building codes. The Warranty on this Montigo
Gas Appliance covers only the component parts manufactured by The Companies. The use of components manufactured by others with this Montigo Gas
Appliance could create serious safety hazards, may result in the denial of certification by recognized national safety agencies, and could be in violation of
local building codes. This warranty does not cover any damages occurring from the use of any components not manufactured or supplied by The Companies
(2) The Montigo Gas Appliance must be subjected to normal use. The Gas Appliances are designed to burn gas only. Burning conventional fireplace fuels such
as wood, coal or any other solid fuel will cause damage to the Gas Appliance, will produce excessive temperatures and will result in a fire hazard.
Limitations On Liability
It is expressly agreed and understood that The Companies sole obligation, and purchaser's exclusive remedy under this Warranty, under any other warranty,
expressed or implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above.
In no event shall The Companies be responsible for any incidental or consequential damages caused by defects in its products, whether such damage occurs
or is discovered before or after replacement or repair, and whether or not such damage is caused by The Companies negligence. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. The duration of any implied warranty
with respect to this Montigo Gas Appliance is limited to the duration of the foregoing warranty. Some states do not allow limitation on how long an implied warranty
lasts, so the above may not apply to you.
Investigation Of Claims Against Warranty
The Companies reserves the right to investigate any and all claims against this Warranty and to decide upon method of settlement.
The Companies Are Not Responsible For Work Done Without Written Consent
The Companies shall in no event be responsible for any warranty work done without first obtaining The Companies written consent.
Dealers Have No Authority To Alter This Warranty
The Companies employees and dealers have no authority to make any warranties nor to authorize any remedies in addition to or inconsistent with those stated above.
How To Register A Claim Against Warranty
In order for any claim under this Warranty to be valid, The Companies must be notified of the claimed defect in writing or by telephone, as soon as reasonably
possible after the defect is discovered. Claims against this Warranty in writing should include the date of installation, and a description of the defect.
Other Rights
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
NOTE:
The Companies as stated above refer to - Canadian Heating Products Inc. and/or Montigo Del Ray Corp.
Canadian Heating Products Inc. and/or Montigo DelRay Corp. reserves the right to make changes at any time, without notice, in design, materials,
specifications, prices and also to discontinue colors, styles and products.
Part No. XG0773 - 032211
Page 29
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Appendix C - State of Massachusetts
Amendment
(Gas Fireplace / Equipment sold in the State of Massachusetts)
5.08: Modifications to NFPA-54, Chapter 10
(1) Revise NFPA-54 section 10.5.4.2 by adding a second exception as follows:
Existing chimneys shall be permitted to have their use continued when a gas conversion burner is installed, and shall be equipped with a manually reset device
that will automatically shut off the gas to the burner in the event of a sustained back-draft.
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes,
including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in
the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gas fitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the floor
level where the gas equipment is to be installed. In addition, the installing plumber or gas fitter shall observe that a battery operated or hard wired carbon
monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled
equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon
monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with
alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days
to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm
shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet
above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print
size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless,
upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the
Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes. (c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions
provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies “special venting systems”,
the following requirements shall be satisfied by the manufacturer:
1. The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and
2. The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for
venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.
(3) After NFPA-54 section 10.10.4.2 add a new section 10.10.4.3 as follows:
When more than four gas appliances are to be vented through a common gas vent or common horizontal vent manifold, a plan of the proposed vent installation
shall be submitted to the Inspector and the serving gas supplier for review and approval.
Extraction from: Massachusets Rules and Regulations
5.00: Amendments To 2002 Edition Of ANSI Z223.1-NFPA-54
Page 30
Part No. XG0773 - 032211
R520-ST & R620-ST Power Vent Indoor Gas Fireplace
Notes
Part No. XG0773 - 032211
Page 31
XG0773 - 032211
Canadian Heating Products Inc.
Langley, BC V4W 4A1
Montigo Del Ray Corp.
Ferndale, WA 98248