Product Manual
Momentus Thin Series SATA
®
ST92503010AS
ST91603010AS
100586949
Rev. A
October 2009
Revision history
Revision
Rev. A
Date
10/21/09
Sheets affected or comments
Initial release.
Copyright © 2009 Seagate Technology LLC. All rights reserved. Printed in U.S.A.
Publication number: 100586949, Rev. A August 2009
Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC
in the United States and/or other countries. Momentus and SeaTools are either trademarks or registered
trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or
other countries. All other trademarks or registered trademarks are the property of their respective owners. No part of this publication may be reproduced in any form without written permission of Seagate
Technology LLC. Contact Seagate at 1-800-654-3685 for copyright requests.
One gigabyte, or GB, equals one billion bytes and one terabyte, or TB, equals one trillion bytes. Your
computer's operating system may use a different standard of measurement and report a lower capacity.
In addition, some of the listed capacity is used for formatting and other functions, and thus will not be
available for data storage. Seagate reserves the right to change, without notice, product offerings or
specifications.
Contents
1.0
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1
About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.0
Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.1
Specification summary table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.2
Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2.1
LBA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.3
Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.4
Physical organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.5
Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.6
Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.7
Seek time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.8
Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.9
Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.9.1
Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.9.2
Deferred spinup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.9.3
Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.9.4
Voltage tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.9.5
Power-management modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.10
Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.10.1
Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.10.2
Temperature gradient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.10.3
Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.10.4
Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.10.5
Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.10.6
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.11
Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.12
Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.13
Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.14
Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.14.1
Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.14.2
Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.14.3
FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.15
Environmental protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.15.1
European Union Restriction of Hazardous Substances (RoHS) . . . . . . . . . . . . 15
2.15.2
China Restriction of Hazardous Substances (RoHS) Directive . . . . . . . . . . . . . 15
2.16
Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.0
Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1
Handling and static-discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2
Configuring the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3
Serial ATA cables and connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4
Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
16
17
17
18
4.0
Serial ATA (SATA) interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1
Hot-Plug compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2
Serial ATA device plug connector pin definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3
Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.1
Identify Device command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2
Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.3
S.M.A.R.T. commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
19
19
21
24
28
29
5.0
Seagate Technology support services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Momentus Thin Series SATA Product Manual, Rev. A
i
ii
Momentus Thin Series SATA Product Manual, Rev. A
List of Figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Typical +5V only startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Serial ATA connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Mounting dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Momentus Thin Series SATA Product Manual, Rev. A
iii
1.0
Introduction
This manual describes the functional, mechanical and interface specifications for the following Seagate
Momentus® Thin Series SATA model drives:
• ST92503010AS
• ST91603010AS
These drives provide the following key features:
• 5400-RPM spindle speed.
• 8-MB buffer.
• Quiet operation. Fluid Dynamic Bearing (FDB) motor.
• High instantaneous (burst) data-transfer rates (up to 3Gb/s).
• Perpendicular recording technology.
• State-of-the-art cache and on-the-fly error-correction algorithms.
• Native Command Queuing (NCQ) with command ordering.
• Full-track multiple-sector transfer capability without local processor intervention.
• 1000 Gs nonoperating shock and 350 Gs of operating shock.
• SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns.
• The 3D Defense System™, which includes Drive Defense, Data Defense and Diagnostic Defense, offers the
industry’s most comprehensive protection for disk drives.
• Support for S.M.A.R.T. drive monitoring and reporting.
• Support for Read Multiple and Write Multiple commands.
Momentus Thin Series SATA Product Manual, Rev. A
1
1.1
About the Serial ATA interface
The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary
advantages include:
• Easy installation and configuration with true plug-and-play connectivity. It is not normally necessary to set
any jumpers or other configuration options.
• Thinner and more flexible cabling for improved enclosure airflow and ease of installation.
• Scalability to higher performance levels.
In addition, Serial ATA makes the transition from parallel ATA easy by providing legacy software support. Serial
ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disk drive in your current
system and expect all of your existing applications to work as normal.
The Serial ATA interface connects each disk drive in a point-to-point configuration with the Serial ATA host
adapter. There is no master/slave relationship with Serial ATA devices like there is with parallel ATA. If two
drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they
were both “masters” on two separate ports. This essentially means both drives behave as if they are Device 0
(master) devices.
Note.
The host adapter may, optionally, emulate a master/slave environment to host software where two
devices on separate Serial ATA ports are represented to host software as a Device 0 (master) and
Device 1 (slave) accessed at the same set of host bus addresses. A host adapter that emulates a
master/slave environment manages two sets of shadow registers. This is not a typical Serial ATA
environment.
The Serial ATA host adapter and drive share the function of emulating parallel ATA device behavior to provide
backward compatibility with existing host systems and software. The Command and Control Block registers,
PIO and DMA data transfers, resets, and interrupts are all emulated.
The Serial ATA host adapter contains a set of registers that shadow the contents of the traditional device registers, referred to as the Shadow Register Block. All Serial ATA devices behave like Device 0 devices. For additional information about how Serial ATA emulates parallel ATA, refer to the “Serial ATA: High Speed Serialized
AT Attachment” specification. The specification can be downloaded from http://www.serialata.org.
2
Momentus Thin Series SATA Product Manual, Rev. A
2.0
Drive specifications
Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal
power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the
ST92503010AS and ST91603010AS models.
2.1
Specification summary table
The specifications listed in this table are for quick reference. For details on specification measurement or definition, see the appropriate section of this manual.
Table 1:
Drive specifications
Drive specification
ST92503010AS
ST91603010AS
Formatted GB (512 bytes/sector)*
250
160
Guaranteed sectors
488,397,168
312,581,808
Bytes per sector
512
Physical read/write heads
2
Discs
1
Cache (MB)
8
Recording density in BPI (bits/in avg)
1434k
Track density TPI (tracks/in avg)
265k
Areal density (Gb/in2 avg)
380
Spindle speed (RPM)
5400
Average latency (ms)
5.6
Internal transfer rate (Mb/s max)
1175
I/O data transfer rate (MB/s max)
300
ATA data-transfer modes supported
SATA 1.0, Serial ATA Revision 2.6
PIO modes 0–4
Multiword DMA modes 0–2
Ultra DMA modes 0–6
Height (max)
7.0 mm (0.276 in)
Width (max)
70.10 mm (2.76 in)
Length (max)
100.55 mm (3.959 in)
Weight (max)
<92.0 g (<0.203 lb)
Power-on to ready (sec typical)
3.4
Standby to ready (sec typical)
1.8
Track-to-track seek time, read (ms typical)
1
Average seek, read (ms typical)
14
Full-stroke seek, read (ms)
30 (max)
Startup current, +5V (max)
1.0A
Seek power (typical)
1.54W
Momentus Thin Series SATA Product Manual, Rev. A
3
Table 1:
Drive specifications
Drive specification
ST92503010AS
ST91603010AS
Read/write power (typical)
Read: 1.4W; Write: 1.78W
Idle mode, low power (typical)
0.58W
Standby mode
0.20W (typical)***
Sleep mode
0.20W (typical)***
Voltage tolerance (including noise)
+5V ± 10%
Ambient temperature
0° to 60°C (operating), –40° to 70°C (nonoperating)
Temperature gradient
(°C per hour max)
20°C (operating)
35°C (nonoperating)
Relative humidity
5% to 95% (operating)
5% to 95% (nonoperating)
Relative humidity gradient
30% per hour max
Wet bulb temperature
(°C max)
37.7 (operating)
40 (nonoperating)
Altitude, operating
–304.8 m to 3,048 m (–1000 ft. to 10,000+ ft.)
Altitude, nonoperating
(meters below mean sea level, max)
–304.8 m to 12,192 m (–1000 ft. to 40,000+ ft.)
Shock, operating (Gs max at 2ms)
350
Shock, nonoperating (Gs max at 2ms)
800
Shock, nonoperating (Gs max at 1ms)
1000
Shock, nonoperating (Gs max at 0.5ms)
600
Vibration, operating
1.0 Gs (0 to peak, 5–500 Hz)
Vibration, nonoperating
5.0 Gs (0 to peak, 5–500 Hz)
Drive acoustics, sound power (bels)
Idle**
2.0 (typical)
2.2 (max)
Performance seek
2.4 (typical)
2.5 (max)
Nonrecoverable read errors
1 per 1014 bits read
Annualized Failure Rate (AFR)
0.48%
Load/Unload (U/UL) cycles
25°C, 50% relative humidity
600,000 software-controlled power on/off cycles
20,000 hard power on/off cycles
32°C, 80% relative humidity
5°C, 80% relative humidity
5°C, 10% relative humidity
55°C, 16% relative humidity
600,000 software-controlled power on/off cycles
20,000 hard power on/off cycles
Warranty
To determine the warranty for a specific drive, use a web browser to access the following web page: support.seagate.com/customer/warranty_validation.jsp
From this page, click on the “Verify Your Warranty” link. You will be asked to provide the
drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for your drive.
Supports Hotplug operation per Serial ATA
Revision 2.6 specification
Yes (requires COMPRESET from host after a hotplug event)
*One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment
and formatting.
**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and
power to operational levels.
***Typical notebooks will pull power to the drive when entering S3 and S4; while in the S3 and S4 states, drive sleep and drive standby
modes will not contribute to battery power consumption.
4
Momentus Thin Series SATA Product Manual, Rev. A
2.2
Formatted capacity
Model
Formatted capacity*
Guaranteed sectors
ST92503010AS
250 GB
488,397,168
ST91603010AS
160 GB
312,581,808
Bytes per sector
512
*One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment
and formatting.
2.2.1
LBA mode
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,
where n is the number of guaranteed sectors as defined above.
See Section 4.3.1, "Identify Device command" (words 60-61 and 100-103) for additional information about 48bit addressing support of drives with capacities over 137 GB.
2.3
Default logical geometry
Cylinders
Read/write heads
Sectors per track
16,383
16
63
LBA mode
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,
where n is the number of guaranteed sectors as defined above.
2.4
Physical organization
Drive model
Read/write heads
Number of discs
2
1
ST92503010AS
ST91603010AS
2.5
Recording and interface technology
Interface
Serial ATA (SATA)
Recording method
Perpendicular
Recording density BPI (bits/in avg)
1434k
Track density TPI (tracks/in avg)
265k
Areal density (Gb/in2 avg)
380
Spindle speed (RPM) (± 0.2%)
5400
Maximum Internal transfer rate (Mb/s)
1175
I/O data-transfer rate (MB/s max)
300
Interleave
1:1
Cache buffer
8 MB (8,192 KB)
Momentus Thin Series SATA Product Manual, Rev. A
5
2.6
Physical characteristics
Drive specification
Height
(mm)
(in)
6.8 +/-0.2
0.268 +/-0.0079
Width
(mm)
(in)
69.85 +/-0.25
2.75 +/-0.0098
Length
(mm)
(in)
100.35 +0.20/-0.25
3.951 +0.008/-0.010
Weight (max)
ST92503010AS and ST91603010AS
2.7
92.0 g
0.203 lb
Seek time
Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using
drive diagnostics. The specifications in the table below are defined as follows:
• Track-to-track seek time is an average of all possible single-track seeks in both directions.
• Average seek time is a true statistical random average of at least 5000 measurements of seeks between
random tracks, less overhead.
Table 2:
Typical seek times
Typical seek times (ms)
Read
Track-to-track
1
Average
14
Full-stroke
30 (max)
Average latency
5.56
Note.
2.8
6
These drives are designed to consistently meet the seek times represented in this manual. Physical
seeks, regardless of mode (such as track-to-track and average), are expected to meet the noted
values. However, due to the manner in which these drives are formatted, benchmark tests that
include command overhead or measure logical seeks may produce results that vary from these
specifications.
Start/stop times
Time to ready
Typical
Max @ 25°C
Power-on to Ready (sec)
3.4
3.6
Standby to Ready (sec)
1.8
2.0
Momentus Thin Series SATA Product Manual, Rev. A
2.9
Power specifications
The drive receives DC power (+5V) through a native SATA power connector.
2.9.1
Power consumption
Power requirements for the drives are listed in the table on page 7. Typical power measurements are based on
an average of drives tested, under nominal conditions, at 25°C ambient temperature.
• Spinup power
Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.
• Seek mode
During seek mode, the read/write actuator arm moves toward a specific position on the disk surface and does
not execute a read or write operation. Servo electronics are active. Seek mode power is measured based on
three random seek operations every 100ms. This mode is not typical.
• Read/write power and current
Read/write power is measured with the heads on track, based on three 63 sector read or write operations
every 100ms.
• Idle mode power
Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in
a random track location.
• Standby mode
During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/
write electronics are in power-down model
Table 3:
DC power
Power dissipation
+5V input average (25° C)
Spinup (max)
1.00A
Seek
1.54W
Read
1.40W
Write
1.78W
Idle, performance*
1.30W
Idle, active*
0.70W
Idle, low power mode*
0.58W
Standby**
0.20W
Sleep
0.20W
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and
power to operational levels.
**Standby power is measured at steady state (after 200ms from transition)
Momentus Thin Series SATA Product Manual, Rev. A
7
2.9.1.1
Typical current profile
Figure 1. Typical +5V only startup and operation current profile
2.9.2
Deferred spinup
Momentus Thin Series SATA drives do not support the deferred spinup option. If you require this option, refer
to the Momentus 5400.3 SATA Blade Server family of drives.
2.9.3
Conducted noise
Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on
the +5 volt line.
Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave
injected noise at up to 10 MHz.
Note.
Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write
current.
2.9.4
Voltage tolerance
Voltage tolerance (including noise):
5V ± 10%
8
Momentus Thin Series SATA Product Manual, Rev. A
2.9.5
Power-management modes
The drive provides programmable power management to provide greater energy efficiency. In most systems,
you can control power management through the system setup program. The drive features the following
power-management modes:
Table 4:
Power management modes
Power modes
Heads
Spindle
Buffer
Active (operating)
Tracking
Rotating
Full power
Idle, performance
Tracking
Rotating
Self refresh—low power
Idle, active
Floating
Rotating
Self refresh—low power
Idle, low power
Parked
Rotating
Self refresh—low power
Standby
Parked
Stopped
Self refresh—low power
Sleep
Parked
Stopped
Self refresh—low power
• Active mode
The drive is in Active mode during the read/write and seek operations.
• Idle mode
The buffer remains enabled, and the drive accepts all commands and returns to Active mode any time disk
access is necessary.
• Standby mode
The drive enters Standby mode when the host sends a Standby Immediate command. If the host has set the
standby timer, the drive can also enter Standby mode automatically after the drive has been inactive for a
specifiable length of time. The standby timer delay is established using a Standby or Idle command. In Standby
mode, the drive buffer is in Self Refresh Low Power mode, the heads are parked and the spindle is at rest.
The drive accepts all commands and returns to Active mode any time disk access is necessary.
• Sleep mode
The drive enters Sleep mode after receiving a Sleep command from the host. In Sleep mode, the drive buffer
is in Self Refresh Low Power mode, the heads are parked and the spindle is at rest. The drive leaves Sleep
mode after it receives a Hard Reset or Soft Reset from the host. After receiving a reset, the drive exits Sleep
mode and enters Standby mode with all current translation parameters intact.
• Idle and Standby timers
Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and
begins counting down from its specified delay times to zero. If the standby timer reaches zero before any
drive activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the
drive accepts all commands and returns to Active mode when disk access is necessary.
Momentus Thin Series SATA Product Manual, Rev. A
9
2.10
Environmental specifications
2.10.1
Ambient temperature
Ambient temperature is defined as the temperature of the environment immediately surrounding the drive.
Actual drive case temperature should not exceed 65°C (149°F) within the operating ambient conditions.
Above 1000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet.
Operating:
0° to 60°C (32° to 140°F)
Nonoperating:
–40° to 70°C (–40° to 158°F)
2.10.2
Temperature gradient
Operating
20°C per hour (68°F per hour max), without condensation
Nonoperating
35°C per hour (95°F per hour max), without condensation
2.10.3
Humidity
2.10.3.1
Relative humidity
Operating
5% to 95% noncondensing (30% per hour max)
Nonoperating
5% to 95% noncondensing (30% per hour max)
2.10.3.2
Wet bulb temperature
Operating
37.7°C (99.86°F max)
Nonoperating
40°C (104°F max)
2.10.4
Altitude
Operating
–304.8 m to 3,048 m (–1000 ft to 10,000+ ft)
Nonoperating
–304.8 m to 12,192 m (–1000 ft to 40,000+ ft)
10
Momentus Thin Series SATA Product Manual, Rev. A
2.10.5
Shock
All shock specifications assume that the drive is mounted securely with the input shock applied at the drive
mounting screws. Shock may be applied in the X, Y or Z axis.
2.10.5.1
Operating shock
These drives comply with the performance levels specified in this document when subjected to a maximum
operating shock of 350 Gs based on half-sine shock pulses of 2ms. Shocks should not be repeated more than
two times per second.
2.10.5.2
Nonoperating shock
The nonoperating shock level that the drive can experience without incurring physical damage or degradation
in performance when subsequently put into operation is 800 Gs based on a nonrepetitive half-sine shock pulse
of 2ms duration.
The nonoperating shock level that the drive can experience without incurring physical damage or degradation
in performance when subsequently put into operation is 1000 Gs based on a nonrepetitive half-sine shock
pulse of 1ms duration.
The nonoperating shock level that the drive can experience without incurring physical damage or degradation
in performance when subsequently put into operation is 600 Gs based on a nonrepetitive half-sine shock pulse
of 0.5ms duration.
2.10.6
Vibration
All vibration specifications assume that the drive is mounted securely with the input vibration applied at the
drive mounting screws. Vibration may be applied in the X, Y or Z axis.
2.10.6.1
Operating vibration
The maximum vibration levels that the drive may experience while meeting the performance standards specified in this document are specified below.
5–500 Hz
2.10.6.2
1.0 Gs (0 to peak). Max displacement may apply below 10Hz.
Nonoperating vibration
The maximum nonoperating vibration levels that the drive may experience without incurring physical damage or degradation in performance when subsequently put into operation are specified below.
5–500 Hz:
5.0 Gs (0 to peak). Max displacement may apply below 22Hz.
Momentus Thin Series SATA Product Manual, Rev. A
11
2.11
Acoustics
Drive emission of sound is measured consistent with the ECMA-74 and its’ referenced standards. Testing is
conducted at room temperature (approximately 25°C). Emission levels are reported as the total A-weighted
sound power levels for steady state, idle, and active seek modes of operation.
Table 5:
Drive A-weighted Sound Power Levels (SWL, BA)
Idle*
Performance seek
2.0 bels (typ)
2.2 bels (max)
2.4 bels (typ)
2.5 bels (max)
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and
power to operational levels.
Test for Prominent Discrete Tones (PDTs)
Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this process is the use of the absolute threshold of hearing. Seagate uses the lower limit for the threshold curve* to
discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone
ratios according to Annex D of the ECMA-74 standards.
*Defined as the median curve given by ISO 389-7 (Tf curve) minus 10dB at all frequencies.
2.12
Electromagnetic immunity
When properly installed in a representative host system, the drive operates without errors or degradation in
performance when subjected to the radio frequency (RF) environments defined in the following table:
Table 6:
Radio frequency environments
Test
Description
Performance
level
Reference
standard
Electrostatic discharge
Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV
B
EN 61000-4-2: 95
Radiated RF immunity
80 to 2000 MHz, 10 V/m,
80% AM with 1 kHz sine
900 MHz, 3 V/m, 50% pulse modulation @ 200 Hz
A
EN 61000-4-3: 96
ENV 50204: 95
Electrical fast transient
± 1 kV on AC mains, ± 0.5 kV on external I/O
B
EN 61000-4-4: 95
Surge immunity
± 1 kV differential, ± 2 kV common, AC mains
B
EN 61000-4-5: 95
Conducted RF immunity
150 kHz to 80 MHz, 3 Vrms, 80% AM with 1 kHz
sine
A
EN 61000-4-6: 97
Power Frequency H-field
immunity
1 A/m, 50Hz/60Hz, 3 axes
A
EN 61000-4-8: 97
Voltage dips, interrupts
30% Reduction for 25 cycles
>95% Reduction for 250 cycles
>95%, 0.5 cycles
C
C
B
EN 61000-4-11: 94
12
Momentus Thin Series SATA Product Manual, Rev. A
2.13
Reliability
Measurement type
Specification
Nonrecoverable read errors
1 per 1014 bits read, max.
Annualized Failure Rate (AFR)
<0.48%
Load/Unload (U/UL)
25°C, 50% relative humidity
600,000 software-controlled power on/off cycles
20,000 hard power on/off cycles
32°C, 80% relative humidity
5°C, 80% relative humidity
5°C, 10% relative humidity
55°C, 16% relative humidity
600,000 software-controlled power on/off cycles
20,000 hard power on/off cycles
Warranty
To determine the warranty for a specific drive, use a web browser to access the
following web page: support.seagate.com/customer/warranty_validation.jsp
From this page, click on the “Verify Your Warranty” link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for your drive.
2.14
Agency certification
2.14.1
Safety certification
These products are certified to meet the requirements of UL60950-1, CSA60950-1 and EN60950 and so
marked as to the certify agency.
2.14.2
Electromagnetic compatibility
Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Electromagnetic Compatibility Directive (2004/108/EC) as put into place 20 July 2007. Testing is performed to the
levels specified by the product standards for Information Technology Equipment (ITE). Emission levels are
defined by EN 55022, Class B and the immunity levels are defined by EN 55024.
Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the
directives when used in the test systems, we cannot guarantee that all systems will comply with the directives.
The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if
necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators should
confirm EMC compliance and provide CE marking for their products.
Korean RRL
If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of
Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility
(EMC) Framework requirements of the Radio Research Laboratory (RRL) Communications Commission,
Republic of Korea.
These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic
Susceptibility (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a
Korean-recognized lab.
• Certificate number:
STX-MomentusThin (B)
• Trade name or applicant:
Seagate Technology LLC
• Manufacturing date:
September 17, 2009
• Manufacturer/nationality:
USA, Singapore and China
Momentus Thin Series SATA Product Manual, Rev. A
13
Australian C-Tick (N176)
If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZ
CISPR22 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian
Communication Authority (ACA).
2.14.3
FCC verification
These drives are intended to be contained solely within a personal computer or similar enclosure (not attached
as an external device). As such, each drive is considered to be a subassembly even when it is individually marketed to the customer. As a subassembly, no Federal Communications Commission verification or certification
of the device is required.
Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total
assembly (enclosure, disk drive, motherboard, power supply, etc.) does comply with the limits for a Class B
computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is
likely to result in interference to radio and television reception.
Radio and television interference. This equipment generates and uses radio frequency energy and if not
installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio
and television reception.
This equipment is designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause interference to radio or television, which can be determined by turning the equipment on and off,
you are encouraged to try one or more of the following corrective measures:
• Reorient the receiving antenna.
• Move the device to one side or the other of the radio or TV.
• Move the device farther away from the radio or TV.
• Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.
If necessary, you should consult your dealer or an experienced radio/television technician for additional suggestions. You may find helpful the following booklet prepared by the Federal Communications Commission:
How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402. Refer to publication number 004-000-00345-4.
14
Momentus Thin Series SATA Product Manual, Rev. A
2.15
Environmental protection
Seagate designs its products to meet environmental protection requirements worldwide, including regulations
restricting certain chemical substances.
2.15.1
European Union Restriction of Hazardous Substances (RoHS)
The European Union Restriction of Hazardous Substances (RoHS) Directive, restricts the presence of chemical substances, including Lead, Cadmium, Mercury, Hexavalent Chromium, PBB and PBDE, in electronic products, effective July 2006. This drive is manufactured with components and materials that comply with the RoHS
Directive.
2.15.2
China Restriction of Hazardous Substances (RoHS) Directive
This product has an Environmental Protection Use Period (EPUP) of 20 years. The following
table contains information mandated by China's "Marking Requirements for Control of Pollution
Caused by Electronic Information Products" Standard.
"O" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is lower
than the threshold defined by the China RoHS MCV Standard.
“O”表示该部件(于同类物品程度上)所含的危险和有毒物质低于中国RoHS MCV标准所定义的门槛值。
"X" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is over
the threshold defined by the China RoHS MCV Standard.
“X”表示该部件(于同类物品程度上)所含的危险和有毒物质超出中国RoHS MCV标准所定义的门槛值。
2.16
Corrosive environment
Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to
light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM
B845. However, this accelerated testing cannot duplicate every potential application environment.
Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive chemicals as electronic drive component reliability can be affected by the installation environment. The silver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide,
chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components
should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or
exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulcanized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any
electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.
Momentus Thin Series SATA Product Manual, Rev. A
15
3.0
Configuring and mounting the drive
This section contains the specifications and instructions for configuring and mounting the drive.
3.1
Handling and static-discharge precautions
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following standard handling and static-discharge precautions:
Caution:
• Keep the drive in the electrostatic discharge (ESD) bag until you are ready for installation to limit the drive’s
exposure to ESD.
• Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal
chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire
installation procedure.
• Handle the drive only by its edges or frame.
• The drive is fragile—handle it with care. Do not press down on the drive top cover.
• Always rest the drive on a padded, antistatic surface until you mount it in the computer.
• Do not touch the connector pins or the printed circuit board.
• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids
the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are
used to seal out dirt and contamination.
16
Momentus Thin Series SATA Product Manual, Rev. A
3.2
Configuring the drive
Each drive on the Serial ATA interface connects in a point-to-point configuration with the Serial ATA host
adapter. There is no master/slave relationship because each drive is considered a master in a point-to-point
relationships. If two drives are attached on one Serial ATA host adapter, the host operating system views the
two devices as if they were both “masters” on two separate ports. This means both drives behave as if they are
Device 0 (master) devices.
Serial ATA drives are designed for easy installation. It is normally not necessary to set any jumpers on this
drive for proper operation. If the host system does not support SATA 3Gb/s operation, place a jumper on pins 1
and 2 to limit the drive to 1.5Gb/s operation.
3.0 Gbits per second operation
Limit data transfer rate to
1.5 Gbits per second
Jumper block
SATA power connector
SATA interface connector
Figure 2. Serial ATA connectors
3.3
Serial ATA cables and connectors
The Serial ATA interface cable consists of four conductors in two differential pairs, plus three ground connections. The cable size may be 30 to 26 AWG with a maximum length of one meter (39.37 inches). See Table 7
for connector pin definitions. Either end of the SATA signal cable can be attached to the drive or host.
For direct backplane connection, the drive connectors are inserted directly into the host receptacle. The drive
and the host receptacle incorporate features that enable the direct connection to be hot pluggable and blind
mateable.
For installations which require cables, you can connect the drive as illustrated in Figure 3.
SATA interface connector
Power connector
SATA interface cable
Power cable
Figure 3. Attaching SATA cabling
Each cable is keyed to ensure correct orientation.
Momentus Thin Series SATA Product Manual, Rev. A
17
3.4
Drive mounting
You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting
holes. See Figure 4 for drive mounting dimensions. Follow these important mounting precautions when mounting the drive:
• Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.
• Use only M3 UNC mounting screws.
• Do not overtighten the mounting screws. Maximum torque: 4.0 in-lb (0.4519 N-m).
• Four (4) threads (0.080 inches, 2.032 mm) minimum screw engagement recommended.
• Avoid excessive drive distortion when mounting. Refer to the following specifications for stiffness/deflection
information:
Top cover stiffness/deflection
Operating with no performance degradation, emitted noise,
mechanical damage, or hard errors
10 mm probe: 1.02kgf or
5 mm probe: 0.92kgf
Non-operating with no hard errors
20 mm probe: 2kgf at any point of top cover
20 mm probe: 15kgf at top cover edges only
Measurements shown in Figure 4 are in inches.
Figure 4. Mounting dimensions—top, side and end view
18
Momentus Thin Series SATA Product Manual, Rev. A
4.0
Serial ATA (SATA) interface
These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA
programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. The drive
also supports the use of the IORDY signal to provide reliable high-speed data transfers.
For detailed information about the Serial ATA interface, refer to the “Serial ATA: High Speed Serialized AT
Attachment” specification.
4.1
Hot-Plug compatibility
Momentus Thin Series SATA drives incorporate connectors which enable you to hot plug these drives in accordance with the Serial ATA: High Speed Serialized AT Attachment specification revision 2.0. This specification
can be downloaded from http://www.serialata.org. This device requires a COMRESET from the host after a
hotplug event.
4.2
Serial ATA device plug connector pin definitions
Table 7 summarizes the signals on the Serial ATA interface and power connectors.
Table 7:
Segment
Signal
Serial ATA connector pin definitions
Pin
Function
Definition
S1
Ground
2nd mate
S2
A+
Differential signal pair A from Phy
S3
A-
S4
Ground
2nd mate
S5
B-
Differential signal pair B from Phy
S6
B+
S7
Ground
2nd mate
Key and spacing separate signal and power segments
Momentus Thin Series SATA Product Manual, Rev. A
19
Table 7:
Segment
Power
Serial ATA connector pin definitions
Pin
Function
Definition
P1
V33
3.3V power
P2
V33
3.3V power
P3
V33
3.3V power, pre-charge, 2nd mate
P4
Ground
1st mate
P5
Ground
2nd mate
P6
Ground
2nd mate
P7
V5
5V power, pre-charge, 2nd mate
P8
V5
5V power
P9
V5
5V power
P10
Ground
2nd mate
P11
Reserved
The pin corresponding to P11 in the backplane receptacle connector is also reserved
The corresponding pin to be mated with P11 in the power cable receptacle connector
shall always be grounded
P12
Ground
1st mate.
P13
V12
12V power, pre-charge, 2nd mate
P14
V12
12V power
P15
V12
12V power
Notes:
1. All pins are in a single row, with a 1.27 mm (0.050”) pitch.
2. The comments on the mating sequence apply to the case of backplane blindmate connector only. In this
case, the mating sequences are:
• the ground pins P4 and P12.
• the pre-charge power pins and the other ground pins.
• the signal pins and the rest of the power pins.
3. There are three power pins for each voltage. One pin from each voltage is used for pre-charge when
installed in a blind-mate backplane configuration.
4. All used voltage pins (Vx) must be terminated.
20
Momentus Thin Series SATA Product Manual, Rev. A
4.3
Supported ATA commands
The following table lists Serial ATA standard commands that the drive supports. For a detailed description of
the ATA commands, refer to the Serial ATA: High Speed Serialized AT Attachment specification. See
“S.M.A.R.T. commands” on page 29.for details and subcommands used in the S.M.A.R.T. implementation.
Command name
Command code (in hex)
ATA-standard commands
Device Configuration Restore
B1h/C0h
Device Configuration Freeze Lock
B1h/C1h
Device Configuration Identify
B1h/C2h
Device Configuration Set
B1h/C3h
Download Microcode
92h
Execute Device Diagnostics
90h
Flush Cache
E7h
Flush Cache Extended
EAh
Identify Device
ECh
Initialize Device Parameters
91h
Read Buffer
E4h
Read DMA
C8h
Read DMA Extended
25h
Read DMA without Retries
C9h
Read Long with Retries
22h
Read Long without Retries
23h
Read Multiple
C4h
Read Multiple Extended
29h
Read Native Max Address
F8h
Read Native Max Address Extended
27h
Read Sectors
20h
Read Sectors Extended
24h
Read Sectors without Retries
21h
Read Verify Sectors
40h
Read Verify Sectors Extended
42h
Read Verify Sectors without Retries
41h
Seek
70h
Set Features
EFh
Set Max Address
F9h
Momentus Thin Series SATA Product Manual, Rev. A
21
Command name
Command code (in hex)
Note: Individual Set Max commands are identified by the value placed in the Set Max Features register as defined to the right.
Address:
Password:
Lock:
Unlock:
Freeze Lock:
Set Multiple Mode
C6h
S.M.A.R.T. Disable Operations
B0h/D9h
S.M.A.R.T. Enable/Disable Autosave
B0h/D2h
S.M.A.R.T. Enable Operations
B0h/D8h
S.M.A.R.T. Enable/Disable Auto Offline
B0h/DBh
S.M.A.R.T. Enable One Attribute Modification
B0h/E0h
S.M.A.R.T. Execute Offline
B0h/D4h
S.M.A.R.T. Read Attribute Thresholds
B0h/D1h
S.M.A.R.T. Read Data
B0h/D0h
S.M.A.R.T. Read Log Sector
B0h/D5h
S.M.A.R.T. Return Status
B0h/DAh
S.M.A.R.T. Save Attribute Values
B0h/D3h
S.M.A.R.T. Write Attribute Thresholds
B0h/D7h
S.M.A.R.T. Write Attribute Values
B0h/E1h
S.M.A.R.T. Write Log Sector
B0h/D6h
Write Buffer
E8h
Write DMA
CAh
Write DMA Extended
35h
Write DMA without Retries
CBh
Write Long with Retries
32h
Write Long without Retries
33h
Write Multiple
C5h
Write Multiple Extended
39h
Write Sectors
30h, 31h
Write Sectors Extended
34h
Write Uncorrectable
45h
00H
01H
02H
03H
04H
ATA-standard power-management commands
Check Power Mode
E5h
Idle
E3h
Idle Immediate
E1h
Sleep
E6h
Standby
E2h
22
Momentus Thin Series SATA Product Manual, Rev. A
Command name
Command code (in hex)
Standby Immediate
E0h
ATA-standard security commands
Security Set Password
F1h
Security Unlock
F2h
Security Erase Prepare
F3h
Security Erase Unit
F4h
Security Freeze Lock
F5h
Security Disable Password
F6h
Momentus Thin Series SATA Product Manual, Rev. A
23
4.3.1
Identify Device command
The Identify Device command (command code ECH) transfers information about the drive to the host following
power up. The data is organized as a single 512-byte block of data, whose contents are shown in the table on
page 27. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or
vary with the state of the drive.
The following commands contain drive-specific features that may not be included in the Serial ATA specification.
Word
Description
Value
0C5AH
0
Configuration information:
• Bit 15: 0 = ATA; 1 = ATAPI
• Bit 7: removable media
• Bit 6: removable controller
• Bit 0: reserved
1
Number of logical cylinders
16,383
2
ATA-reserved
0000H
3
Number of logical heads
16
4
Retired
0000H
5
Retired
0000H
6
Number of logical sectors per logical track: 63
003FH
7–9
Retired
0000H
10–19
Serial number: (20 ASCII characters, 0000H = none)
ASCII
20
Retired
0000H
21
Retired
0400H
22
Obsolete
0000H
23–26
Firmware revision (8 ASCII character string, padded with
blanks to end of string)
x.xx
27–46
Drive model number: (40 ASCII characters, padded with
blanks to end of string)
ST92503010AS
ST91603010AS
47
(Bits 7–0) Maximum sectors per interrupt on Read multiple
and Write multiple (16)
8010H
48
Reserved
0000H
49
Standard Standby timer, IORDY supported and may be disabled
2F00H
50
ATA-reserved
0000H
51
PIO data-transfer cycle timing mode
0200H
52
Retired
0200H
53
Words 54–58, 64–70 and 88 are valid
0007H
54
Number of current logical cylinders
xxxxH
55
Number of current logical heads
xxxxH
56
Number of current logical sectors per logical track
xxxxH
57–58
Current capacity in sectors
xxxxH
24
Momentus Thin Series SATA Product Manual, Rev. A
Word
Description
Value
59
Number of sectors transferred during a Read Multiple or
Write Multiple command
xxxxH
60–61
Total number of user-addressable sectors
This field contains a value that is one greater than the total
number of user-addressable sectors. The maximum value
that shall be placed in this field is 0FFFFFFFh. The
0FFFFFFFh value applies to all capacities over 137GB (see
Section 2.2 and 2.3 for related information).
ST92503010AS
ST91603010AS
62
Retired
0000H
63
Multiword DMA active and modes supported
(see note following this table)
xx07H
64
Advanced PIO modes supported (modes 3 and 4 supported)
0003H
65
Minimum multiword DMA transfer cycle time per word
(120 nsec)
0078H
66
Recommended multiword DMA transfer cycle time per word
(120 nsec)
0078H
67
Minimum PIO cycle time without IORDY flow control
(240 nsec)
00F0H
68
Minimum PIO cycle time with IORDY flow control (120 nsec)
0078H
69–74
ATA-reserved
0000H
75
Queue depth
001FH
76
Serial ATA capabilities
0508H
77
ATA-reserved
0000H
78
Serial ATA features supported
0048H
79
Serial ATA features enabled
0040H
80
Major version number
003EH
81
Minor version number
0028H
82
Command sets supported
306BH
83
Command sets supported
4001H
84
Command sets support extension
4000H
85
Command sets enabled
30xxH
86
Command sets enabled
0001H
87
Command sets enable extension
4000H
88
Ultra DMA support and current mode
(see note following this table)
xx7FH
89
Security erase time
0000H
90
Enhanced security erase time
0000H
92
Master password revision code
FFFEH
93
Hardware reset value
(see description following this table)
xxxxH
94
Auto acoustic management setting
xxxxH
Momentus Thin Series SATA Product Manual, Rev. A
= 0FFFFFFFh
= 0FFFFFFFh
25
Word
Description
Value
95–99
ATA-reserved
0000H
100–
103
Total number of user-addressable LBA sectors available
(see Section 2.2 for related information)
These words are required for drives that support the 48-bit
addressing feature. Maximum value: 0000FFFFFFFFFFFFh.
ST92503010AS
ST91603010AS
104–
118
ATA-reserved
0000H
119
Free Fall Protection support (bit 5)
1 = Free Fall Protection supported
0 = Free Fall Protection not supported
120
Free Fall Protection enable/disable (bit 5)
1 = Free Fall Protection feature is enabled
0 = Free Fall Protection feature is disabled
121–
127
ATA reserved
0000H
128
Security status
0001H
129–
159
Seagate-reserved
xxxxH
160–
254
ATA-reserved
0000H
255
Integrity word
xxA5H
Note.
= 488,397,168
= 312,581,808
See the bit descriptions below for words 63, 88, and 93 of the Identify Drive data:
Description (if bit is set to 1)
26
Bit
Word 63
0
Multiword DMA mode 0 is supported.
1
Multiword DMA mode 1 is supported.
2
Multiword DMA mode 2 is supported.
8
Multiword DMA mode 0 is currently active.
9
Multiword DMA mode 1 is currently active.
10
Multiword DMA mode 2 is currently active.
Momentus Thin Series SATA Product Manual, Rev. A
Bit
Word 88
0
Ultra DMA mode 0 is supported.
1
Ultra DMA mode 1 is supported.
2
Ultra DMA mode 2 is supported.
3
Ultra DMA mode 3 is supported.
4
Ultra DMA mode 4 is supported.
5
Ultra DMA mode 5 is supported
6
Ultra DMA mode 6 is supported
8
Ultra DMA mode 0 is currently active.
9
Ultra DMA mode 1 is currently active.
10
Ultra DMA mode 2 is currently active.
11
Ultra DMA mode 3 is currently active.
12
Ultra DMA mode 4 is currently active.
13
Ultra DMA mode 5 is currently active.
14
Ultra DMA mode 6 is currently active.
Bit
Word 93
13
1 = 80-conductor cable detected, CBLID above VIH
0 = 40-conductor cable detected, CBLID below VIL
Momentus Thin Series SATA Product Manual, Rev. A
27
4.3.2
Set Features command
This command controls the implementation of various features that the drive supports. When the drive receives
this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted.
Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the
Features register are defined as follows:
Table 8:
Set Features command values
02H
Enable write cache (default).
03H
Set transfer mode (based on value in Sector Count register).
Sector Count register values:
00H Set PIO mode to default (PIO mode 2).
01H Set PIO mode to default and disable IORDY (PIO mode 2).
08H PIO mode 0
09H PIO mode 1
0AH PIO mode 2
0BH PIO mode 3
0CH PIO mode 4 (default)
20H Multiword DMA mode 0
21H Multiword DMA mode 1
22H Multiword DMA mode 2
40H Ultra DMA mode 0
41H Ultra DMA mode 1
42H Ultra DMA mode 2
43H Ultra DMA mode 3
44H Ultra DMA mode 4
45H Ultra DMA mode 5
46H Ultra DMA mode 6
55H
Disable read look-ahead (read cache) feature.
82H
Disable write cache
AAH
Enable read look-ahead (read cache) feature (default).
C1H
Disable the Free Fall Protection feature (41H above enables the Free Fall Protection feature)
F1H
Report full capacity available
Note.
28
At power-on, or after a hardware or software reset, the default values of the features are as indicated above.
Momentus Thin Series SATA Product Manual, Rev. A
4.3.3
S.M.A.R.T. commands
S.M.A.R.T. provides near-term failure prediction for disk drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines
that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable.
S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.
commands and implementation, see the Draft ATA-8 Standard.
SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4H) that eliminates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at:
http://seatools.seagate.com.
This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that
supports S.M.A.R.T. to enable this feature. The table below shows the S.M.A.R.T. command codes that the
drive uses.
Table 9:
S.M.A.R.T. commands
Code in features register
S.M.A.R.T. command
D0H
S.M.A.R.T. Read Data
D1H
Vendor-specific
D2H
S.M.A.R.T. Enable/Disable Attribute Autosave
D3H
S.M.A.R.T. Save Attribute Values
D4H
S.M.A.R.T. Execute Off-line Immediate (runs DST)
D5H
S.M.A.R.T. Read Log Sector
D6H
S.M.A.R.T. Write Log Sector
D7H
Vendor-specific
D8H
S.M.A.R.T. Enable Operations
D9H
S.M.A.R.T. Disable Operations
DAH
S.M.A.R.T. Return Status
Note.
If an appropriate code is not written to the Features Register, the command is aborted and 0x 04
(abort) is written to the Error register.
Momentus Thin Series SATA Product Manual, Rev. A
29
5.0
Seagate Technology support services
Internet
For information regarding Seagate products and services, visit www.seagate.com.
Worldwide support is available 24 hours daily by email for your questions.
Presales Support:
Presales@Seagate.com
Technical Support:
DiscSupport@Seagate.com
Warranty Support:
http://www.seagate.com/www/en-us/support/warranty_&_returns_assistance
mySeagate
my.seagate.com is the industry's first Web portal designed specifically for OEMs and distributors. It provides
self-service access to critical applications, personalized content and the tools that allow our partners to manage their Seagate account functions. Submit pricing requests, orders and returns through a single, passwordprotected Web interface-anytime, anywhere in the world.
spp.seagate.com
spp.seagate.com supports Seagate resellers with product information, program benefits and sales tools. You
may register for customized communications that are not available on the web. These communications contain
product launch, EOL, pricing, promotions and other channel-related information. To learn more about the benefits or to register, go to spp.seagate.com, any time, from anywhere in the world.
Global Customer Support
Presales Support
Our Presales Support staff can help you determine which Seagate products are best suited for your specific
application or computer system, as well as product availability and compatibility.
Technical Support
Seagate technical support is available to assist you online at support.seagate.com or through one of our call
centers. Have your system configuration information and your "ST" model/product number available.
30
Momentus Thin Series SATA Product Manual, Rev. A
Customer Service Operations
Warranty Service
Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct
customers should contact their Seagate Customer Service Operations (CSO) representative for warrantyrelated issues. Resellers or end users of drive products should contact their place of purchase or Seagate warranty service for assistance. Have your serial number and model or part number available.
Data Recovery Services
Seagate offers data recovery services for all formats and all brands of storage media. Our data recovery services labs are currently located throughout the world. Additional information, including an online request form
and data loss prevention resources, is available at http://services.seagate.com/index.aspx.
Authorized Service Centers
Seagate Service Centers are available on a global basis for the return of defective products. See www.seagate.com for the service center near you.
USA/Canada/Latin America support services
For an extensive list of telephone numbers to technical support, presales and warranty service in USA/
Canada/Latin America, including business hours, go to the "Contact Us" page on www.seagate.com.
Global Customer Support
Presales, Technical, and Warranty Support
Call Center
Toll-free
USA, Canada,
and Mexico
1-800-SEAGATE
Data Recovery Services
Call Center
USA, Canada,
and Mexico
Toll-free
1-800-475-0143
Direct dial
+1-405-324-4700
Direct dial
+1-905-474-2162
FAX
1-800-475-0158
+1-905-474-2459
Europe, the Middle East and Africa Support Services
For an extensive list of telephone numbers to technical support, presales and warranty service in Europe, the
Middle East and Africa, go to the "Contact Us" page on www.seagate.com.
Asia/Pacific Support Services
For an extensive list of telephone numbers to technical support, presales and warranty service in Asia/Pacific,
go to the "Contact Us" page on www.seagate.com.
Momentus Thin Series SATA Product Manual, Rev. A
31
32
Momentus Thin Series SATA Product Manual, Rev. A
Index
A
ACA 14
acoustics 4, 12
Active mode 9
Address 21
AFR 13
Agency certification 13
Altitude 10
Altitude, nonoperating 4
Altitude, operating 4
Ambient temperature 4, 10
ambient temperature 6
Annualized Failure Rate 13
Annualized Failure Rate (AFR) 4
Areal density 3, 5
ATA commands 21
ATA data-transfer modes supported 3
Australia/New Zealand Standard AS/NZ CISPR22 14
Australian Communication Authority (ACA) 14
Australian C-Tick 14
Average seek time 6
Average seek, read 3
B
bels 4
BPI 3
buffer 3, 5
Bytes per sector 3, 5
C
cables and connectors 17
Cache 3
cache 5
capacity 5
case temperature 10
CE mark 13
certification 13
Check Power Mode 22
chemical substances 15
China RoHS directive 15
Class B computing device 14
compatibility 13
Conducted noise 8
Conducted RF immunity 12
Configuring the drive 16
connectors 17
CSA60950-1 13
current 3
cycles 13
Cylinders 5
Momentus Thin Series SATA Product Manual, Rev. A
D
data-transfer rates 1
DC power 7
Default logical geometry 5
density 3
Device Configuration Freeze Lock 21
Device Configuration Restore 21
Device Configuration Set 21
Diagnostics 21
dimensions 18
Discs 3
dissipation 7
Download Microcode 21
E
Electrical fast transient 12
Electromagnetic compatibility 13
Electromagnetic Compatibility (EMC) 13
Electromagnetic Compatibility control Regulation 13
Electromagnetic Compatibility Directive (2004/108/
EC) 13
Electromagnetic immunity 12
Electrostatic discharge 12
electrostatic discharge (ESD) 16
EN 55022, Class B 13
EN 55024 13
EN60950 13
Environmental protection 15
Environmental specifications 10
error-correction algorithms 1
errors 4, 13
ESD 16
EU 13
European Union (EU) requirements 13
European Union Restriction of Hazardous Substances 15
evice Configuration Identify 21
Execute Device Diagnostics 21
F
FCC verification 14
features 1
Federal Communications Commission 14
Flush Cache 21
Flush Cache Extended 21
Formatted capacity 5
Formatted Gbytes 3
Freeze Lock 21
G
Gbytes 5
geometry 5
gradient 4
33
Guaranteed sectors 3, 5
guaranteed sectors 5
H
handling 16
Handling precautions 16
heads 5
Height 3
height 6
Humidity 10
humidity 4
I
I/O data-transfer rate 3, 5
Identify 21
Identify Device 21
Identify Device command 24
Idle 7, 22
Idle and Standby timers 9
Idle Immediate 22
Idle mode 4, 9
Idle mode power 7
Information Technology Equipment (ITE) 13
Initialize Device Parameters 21
Input noise ripple 8
Interface 5
interface 19
Interleave 5
Internal data transfer rate 3
Internal data-transfer rate 5
ITE 13
N
noise 8
nominal power 6
Nonoperating shock 11
Nonoperating vibration 11
Nonrecoverable read errors 4
nonrecoverable read errors 13
O
Operating shock 11
Operating vibration 11
P
Physical characteristics 6
Physical organization 5
Physical read/write heads 3
point-to-point 2, 17
Power consumption 7
power dissipation 7
power management 9
power on/off cycles 13
Power specifications 7
Power-management modes 9
Power-on to Ready 6
Power-on to ready 3
precautions 16, 18
programmable power management 9
Q
quick reference 3
K
R
KCC 13
Korean Communications Commission 13
Korean RRL 13
master/slave 2
Max Address 21
maximum temperature 10
Microcode 21
mounting 18
mounting screws 11
mounting the drive 16
Radiated RF immunity 12
Radio and television interference 14
radio frequency (RF) 12
random track location 7
Read Buffer 21
Read DMA 21
Read DMA Extended 21
Read DMA without Retries 21
read errors 4, 13
Read Long with Retries 21
Read Long without Retries 21
Read Multiple 21
Read Multiple Extended 21
Read Native Max Address 21
Read Native Max Address Extended 21
Read Sectors 21
Read Sectors Extended 21
Read Sectors without Retries 21
Read Verify Sectors 21
Read Verify Sectors Extended 21
Read Verify Sectors without Retries 21
34
Momentus Thin Series SATA Product Manual, Rev. A
L
latency 3
LBA mode 5
Length 3
length 6
Load/Unload 13
logical geometry 5
M
Read/write heads 5
Read/write power 4
read/write power and current 7
Recording density 3, 5
Recording method 5
Recording technology 5
Relative humidity 4, 10
Reliability 13
resistance 8
Retries 21
RF 12
RoHS 15
RPM 3
RRL 13
S
S.M.A.R.T. 22
S.M.A.R.T. implementation 21
Safety certification 13
SATA 5, 19
screws 11, 18
sector 5
sectors 5
Sectors per track 5
Security Disable Password 23
Security Erase Prepare 23
Security Erase Unit 23
Security Freeze Lock 23
Security Set Password 23
Security Unlock 23
Seek 21
seek mode 7
Seek power 3
Seek time 6
seek time 3
Seeking 7
Self refresh, low power 9
Serial ATA 5
Serial ATA (SATA) interface 19
serial ATA ports 2
servo electronics 7
Set Features 21
Set Max Address 21
Set Multiple Mode 22
Shock 11
Shock, nonoperating 4
Shock, operating 4
single-track seeks 6
Sleep 7, 22
Sleep mode 4, 9
sound power 4
Specification summary table 3
Spindle speed 3, 5
Spinup 7
spinup power 7
Momentus Thin Series SATA Product Manual, Rev. A
Standby 7, 22
Standby Immediate 23
Standby mode 4, 7, 9
Standby to Ready 6
Standby to ready 3
Start/stop times 6
Startup current 3
static-discharge 16
support services 30
Surge immunity 12
T
technical support services 30
temperature 4, 6, 10
Temperature gradient 4, 10
timers 9
TPI 3
Track density 3, 5
Track-to-track seek time 3, 6
U
UL60950-1 13
V
Vibration 11
Vibration, nonoperating 4
Vibration, operating 4
Voltage dips, interrupts 12
Voltage tolerance 4, 8
W
Warranty 13
Weight 3
weight 6
Wet bulb temperature 4, 10
Width 3
width 6
Write Buffer 22
Write DMA 22
Write DMA Extended 22
Write Long with Retries 22
Write Long without Retries 22
Write Multiple 22
Write Sectors 22
Write Sectors Extended 22
write uncorrectable 22
35
36
Momentus Thin Series SATA Product Manual, Rev. A
Seagate Technology LLC
920 Disc Drive, Scotts Valley, California 95066-4544, USA
Publication Number: 100586949, Rev. A, Printed in USA