ViewSonic Pro8520HD User guide

Pro8520HD
DLP Projector
User Guide
IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://
www.viewsonic.com in English, or in specific languages using the Regional selection
box in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”
Model No. VS14804
Compliance Information
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
yy
Reorient or relocate the receiving antenna.
yy
Increase the separation between the equipment and receiver.
yy
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
yy
Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modifications not expressly approved
by the party responsible for compliance could void your authority to operate the
equipment.
For Canada
CAN ICES-3 (B)/NMB-3(B)
CE Conformity for European Countries
The device complies with the EMC Directive 2004/108/EC and Low Voltage Directive 2006/95/EC.
Following information is only for EU-member states:
The mark is in compliance with the Waste Electrical and Electronic
Equipment Directive 2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment
including any spent or discarded batteries or accumulators as unsorted
municipal waste, but use the return and collection systems available.
If the batteries, accumulators and button cells included with this equipment,
display the chemical symbol Hg, Cd, or Pb, then it means that the battery
has a heavy metal content of more than 0.0005% Mercury or more than,
0.002% Cadmium, or more than 0.004% Lead.
i
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this unit near water.
Clean with a soft, dry cloth.
Do not block any ventilation openings. Install the unit in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other devices (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade and the third
prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched particularly at plugs.
Convenience receptacles and the point where they exit from the unit. Be sure
that the power outlet is located near the unit so that it is easily accessible.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the unit. When a cart is used, use
caution when moving the cart/unit combination to avoid injury from
tipping over.
13. Unplug this unit when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
unit has been damaged in any way, such as: if the power-supply cord or plug is
damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed
to rain or moisture, or if the unit does not operate normally or has been dropped.
ii
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive
2011/65/EU of the European Parliament and the Council on restriction of the use
of certain hazardous substances in electrical and electronic equipment (RoHS2
Directive) and is deemed to comply with the maximum concentration values issued
by the European Technical Adaptation Committee (TAC) as shown below:
Substance
Proposed Maximum
Concentration
Actual Concentration
Lead (Pb)
0.1%
< 0.1%
Mercury (Hg)
0.1%
< 0.1%
Cadmium (Cd)
0.01%
< 0.01%
Hexavalent Chromium (Cr )
0.1%
< 0.1%
Polybrominated biphenyls (PBB)
0.1%
< 0.1%
Polybrominated diphenyl ethers (PBDE)
0.1%
< 0.1%
6+
Certain components of products as stated above are exempted under the Annex III
of the RoHS2 Directives as noted below:
Examples of exempted components are:
1.Mercury in cold cathode fluorescent lamps and external electrode fluorescent
lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):
(1) Short length (≦500 mm): maximum 3.5 mg per lamp.
(2) Medium length (>500 mm and ≦1,500 mm): maximum 5 mg per lamp.
(3) Long length (>1,500 mm): maximum 13 mg per lamp.
2.Lead in glass of cathode ray tubes.
3.Lead in glass of fluorescent tubes not exceeding 0.2% by weight.
4.Lead as an alloying element in aluminium containing up to 0.4% lead by weight.
5.Copper alloy containing up to 4% lead by weight.
6.Lead in high melting temperature type solders (i.e. lead-based alloys containing
85% by weight or more lead).
7.Electrical and electronic components containing lead in a glass or ceramic other
than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or
ceramic matrix compound.
iii
Copyright Information
Copyright © ViewSonic® Corporation, 2013. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks
of Microsoft Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered
trademarks of ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association.
DPMS and DDC are trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines
Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors
or omissions contained herein; nor for incidental or consequential damages resulting
from furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves
the right to change product specifications without notice. Information in this document may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means,
for any purpose without prior written permission from ViewSonic Corporation.
Product Registration
To fulfill possible future product needs, and to receive additional product information
as it becomes available, please visit your region section on ViewSonic’s website to
register your product online.
The ViewSonic CD also provides an opportunity for you to print the product
registration form. Upon completion, please mail or fax to a respective ViewSonic
office. To find your registration form, use the directory “:\CD\Registration”.
Registering your product will best prepare you for future customer service needs.
Please print this user guide and fill the information in the “For Your Records” section.
Your LCD displays serial number is located on the rear side of the display.
For additional information, please see the “Customer Support” section in this guide.
Product Name:
Model Number:
Document Number:
Serial Number:
Purchase Date:
For Your Records
Pro8520HD
ViewSonic DLP Projector
VS14804
Pro8520HD_UG_ENG Rev. 1B 05-15-13
________________________________
________________________________
Product disposal at end of product life
The lamp in this product contains mercury which can be dangerous to you and the
environment. Please use care and dispose of in accordance with local, state or
federal laws.
ViewSonic respects the environment and is committed to working and living green.
Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic
website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx
iv
Notes on the AC Power Cord
AC Power Cord must meet the requirement of countries where you use this projector.
Please confirm your AC plug type with the graphics below and ensure that the proper
AC Power Cord is used. If the supplied AC Power Cord does not match your AC outlet, please contact your sales dealer. This projector is equipped with a grounding type
AC line plug. Please ensure that your outlet fits the plug. Do not defeat the safety purpose of this grounding type plug. We highly recommend using a video source device
also equipped with a grounding type AC line plug to prevent signal interference due to
voltage fluctuations.
Ground
Ground
For the U.S.A. and
Canada
For Australia and
Mainland China
Ground
Ground
For Continental Europe
For the U.K.
v
Table of contents
Introduction ........................................................................................... 1
Projector Features ................................................................................................................................. 1
Package Contents .................................................................................................................................. 2
Projector Overview ................................................................................................................................. 3
Using the Product ................................................................................. 5
Control Panel ......................................................................................................................................... 5
Connection Ports ................................................................................................................................... 6
Remote Control ...................................................................................................................................... 8
Installing the Batteries .......................................................................................................................... 10
Remote Control Operation ................................................................................................................... 11
Connection .......................................................................................... 12
Connecting a computer or monitor ....................................................................................................... 13
Connecting Video source devices ........................................................................................................ 14
Operation ............................................................................................. 17
Powering On/Off the Projector ............................................................................................................. 17
Adjusting the Projector Height ............................................................................................................. 18
Adjusting the Projector Zoom and Focus ............................................................................................. 18
Adjusting Projection Image Size .......................................................................................................... 19
Locking control keys ............................................................................................................................ 20
Menu Operation ................................................................................................................................... 21
Controlling the projector through a LAN environment .......................................................................... 30
Controlling the projector through a web browser ................................................................................. 33
Displaying images through vsPresenter .............................................................................................. 38
Displaying pictures with a USB storage device .................................................................................... 42
Maintenance ........................................................................................ 45
Cleaning the Lens ................................................................................................................................ 45
Cleaning the Projector Housing ........................................................................................................... 45
Cleaning the Filter Cover ..................................................................................................................... 45
Replacing the Lamp ............................................................................................................................. 46
Specifications ..................................................................................... 48
Dimensions .......................................................................................................................................... 49
Ceiling mount installation ..................................................................................................................... 49
Appendix .............................................................................................. 50
LED Indicator Messages ..................................................................................................................... 50
Compatibility Modes ............................................................................................................................. 51
Troubleshooting ................................................................................................................................... 52
RS-232 Command and Configuration .................................................................................................. 53
IR Control Code ................................................................................................................................... 55
vi
Introduction
Projector Features
The projector integrates high-performance optical engine projection and a user - friendly
design to deliver high reliability and ease of use.
The projector offers the following features:
• Single chip 0.65" Texas Instruments DLP® technology
• 1080p (1920 x 1080 pixels)
Compatibility with Macintosh® computers
Compatibility with NTSC, PAL, SECAM and HDTV
D-Sub 15-pin terminal for analog video connectivity
User-friendly, multi-language on-screen display
Advanced electronic keystone correction
RS-232 connector for serial control
HDMI compatibility
PJLinkTM compatible
LAN Settings allowing management of projector status from a remote computer
LAN display 4-1 (maximum 4PC/ NB display to 1 projector)
LAN display 1-M available (1PC/ NB can display to maximum 8 projectors at the
same time)
• USB display supports computer connection via USB mini-B type to A type cable
• Support USB flash drive for JPEG presentation
• Less than 0.5 W power consumption in standby mode
•
•
•
•
•
•
•
•
•
•
•
Note
• The information in this manual is subject to change without notices.
• The reproduction, transfer or copy of all or any part of this document is not permitted
without express written consent.
1
Package Contents
When you unpack the projector, make sure you have all these components:
HDMI1
HDMI2
Video
Compo
PC
Auto
Enter
Swap
Default
AC Power Cord
Remote Control (IR) & batteries
VGA Cable (D-SUB to DSUB)
HDMI Cable
ViewSonic
DVD Wizard
RS232 cable
RGB to component adapter
ViewSonic
Projector with Lens Cap
Quick Start
Guide
Optional accessories
Filter cover
Projector Carrying Case
Note
• Contact you dealer immediately if any items are missing, appear damaged, or if the unit
does not work.
• For maximum protection of the product, please save the original shipping carton and
packing materials and repack your product as it was originally packed at the factory if
you need to ship it.
2
Projector Overview
Front View
13
1
12
2 3 4 5
11
10
6
1. Lens cap
3. Elevator foot
5. Projection lens
7. Ventilation holes (intake)
9. Speaker
11. Zoom ring
13. Lamp cover
9
7
8
2. Elevator button
4. Lens cap strap
6. Front IR remote control sensor
8. Filter cover
10. Focus ring
12. Control panel
3
Rear View
1
2
3
1. Connection ports
3. Kensington lock
5. Speaker
4
5
6
2. AC power socket
4. Rear IR remote control sensor
6. Ventilation holes (exhaust)
Bottom View
3
1
2
1. Ceiling mount holes (M4*8)
3. Security bar
2. Tilt-adjustment feet
Note
• This projector can be used with a ceiling mount for support. The ceiling mount is not
included in the package.
• Contact your dealer for information to mount the projector on a ceiling.
4
Using the Product
Control Panel
9 1
2
3
4
8
5
6
10
7
1.
4
Power (Power LED indicator)
Refer to “LED Indicator Messages”.
2. TEMP (Temperature LED indicator)
Refer to “LED Indicator Messages”.
3. LAMP (Lamp LED indicator)
Refer to “LED Indicator Messages”.
4. Keystone/Arrow keys ( /Up, /Down)
Manually correct distorted images resulting from an angled projection.
5. Four directional buttons
Use four directional buttons to select items or make adjustments to your selection.
6. ENTER
Enter to sub-menu and confirm the menu selection.
7. SOURCE
Display the source selection bar.
8. MENU/EXIT
Display or exit the on-screen display menus.
9.
Power
Turn the projector on or off.
10. Right/Panel key
Activate panel key lock.
5
Connection Ports
1
2
18
17
3
4
16 15
5 6
7
8
9
14 13 12 11 10
1. RS-232
When operating the projector via a computer, connect this to the controlling computer's RS-232C port.
2. Monitor Out
Connect to a computer display, etc.
3. Component (Y Cb/Pb Cr/Pr)
Connect Y Cb/Pb Cr/Pr output from video equipment to this jack.
4. S-Video
Connect S-Video output from video equipment to this jack.
5. USB B
USB display supports computer connection via USB mini-B type to A type cable.
6. USB A
This connector supports firmware update, USB flash drive display and wireless
dongle for USB display.
7. LAN
For LAN display/network control and web server.
8. HDMI 1
Connect HDMI output from video equipment to this jack.
9. HDMI 2
Connect HDMI output from video equipment to this jack.
10. DC 12V Out
12V DC out
11. MIC in
Microphone input jack.
12. Audio Out
Connect to a speaker or other audio input equipment.
13. Audio 2
Connect an audio output from video equipment or computer to this jack.
14. Audio 1
Connect an audio output from video equipment or computer to this jack.
6
15. Audio 3 (L/R)
Connect an audio output from video equipment to this jack.
16. Video
Connect composite video output from video equipment to this jack.
17. Computer in 2
Connect image input signal (analog RGB or component) to this jack.
18. Computer in 1
Connect image input signal (analog RGB or component) to this jack.
7
Remote Control
HDMI1
3
4
HDMI2
Video
5
4
6
7
8
Compo
PC
Auto
Enter
15
16
17
18
Swap
9
10
11
12
13
14
Default
19
20
21
22
23
24
25
1. Power
Turn the projector on or off.
2. HDMI 1
Display HDMI 1 signal.
3. Video
Switch input source to Composite/S-Video by sequence.
4.
Up/Volume +, Down/Volume When the On-Screen Display (OSD) menu is not activated, adjust the projector’s
sound level.
5.
Left/Mute
When the On-Screen Display (OSD) menu is not activated, this button is used as
mute function.
6. Menu
Display on-screen display menus.
7. User 1
Recall the customized settings based on the current available settings.
8. Source
Display the source selection bar.
9. Gamma
Change the gamma setting.
10. Pattern
Display embedded test pattern.
11. Color Mode
8
Change the image mode setting by sequence.
12. Blank
Cut off the screen temporarily. Press again to cancel the Blank Screen function.
13. Light
Enable backlight functions of the remote control’s buttons.
14. Compo
Display Component video (YPbPr/ YCbCr) signal.
15. HDMI 2
Display HDMI 2 signal.
16. PC
Switch input source to Computer in 1/Computer in 2 by sequence.
17. Auto/Enter
Resynchronize the projector to the input signal from a computer. This function is
available for computer mode only.
Confirmed selections.
18.
Right/ Lock
When the On-Screen Display (OSD) menu is activated, the #4, #5, and #18 keys
are used as directional arrows to select the desired menu items and to make
adjustments.
Activate panel key lock.
19. ESC
Leave current page or items or to close OSD.
20. User 2
Recall the customized settings based on the current available settings.
21. PIP/POP
Switch screen to PIP/POP by sequence.
22. Swap
Swap input source in PIP or POP image.
23. Aspect
Select the display aspect ratio.
24. RGBCMY
Change indivial RGBCMY color (user color setting).
25. Default
Restore settings to factory default.
9
Installing the Batteries
1. Open the battery cover in the
direction shown.
2. Install batteries as indicated by the
diagram inside the compartment.
3. Close the battery cover into position.
Caution
• Risk of explosion if battery is replaced by an incorrect type.
• Dispose of used batteries according to the instructions.
• Make sure the plus and minus terminals are correctly aligned when loading a battery.
Note
• Keep the batteries out of the reach of children. There is a danger of death by
accidentally swallowing the batteries.
• Remove batteries from remote control when not using for extended periods.
• Do not dispose of the used batteries along with household waste. Dispose of used
batteries according to local regulations.
• Danger of explosion may happen if batteries are incorrectly replaced. Replce all the
batteries with new ones.
• Batteries should not be in or near to fire or water, keep batteries in a dark, cool and dry
place.
• If suspect battery leakage, wipe out the leakage and then replace new batteries. If the
leakage adheres to your body or clothes, rinse well with water immediately.
10
Remote Control Operation
Point the remote control at the infrared remote sensor and press a button.
• Operating the projector from the front
15
15
5m
5m m
9
m
7m 5
MI1
HD
HD
eo
Vid
MI2
o
mp
Co
PC
to
Au
ter
En
Sw
ap
lt
fau
De
• Operating the projector from the rear
15
15
5m
5m
9m
MI1
HD
MI2
HD
eo
Vid
o
mp
Co
PC
to
Au
ter
En
Sw
ap
lt
fau
De
Note
• Do not point the laser directly to the people's eyes (especially small children). There is a
danger of injury to the eyes.
• The remote control may not operate when there is sunlight or other strong light such as
a fluorescent lamp shining on the remote sensor.
• Operate the remote control from a position where the remote sensor is visible.
• Do not drop the remote control or jolt it.
• Keep the remote control out of locations with excessively high temperature or humidity.
• Do not get water on the remote control or place wet objects on it.
• Do not disassemble the remote control.
11
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
1
2
3
1
11
9
6
4
7
8
9
7
10
9
5
12
1.
3.
5.
7.
9.
11.
VGA cable (D-Sub to D-Sub)
USB cable (mini-B type to A type)
Component Video cable
S-Video cable
Audio cable
Microphone 3.5 mini jack cable
2. VGA to DVI-A cable
4. VGA (D-Sub) to HDTV (RCA) cable
6. Audio L/R cable
8. Composite Video cable
10. HDMI cable
12. USB flash drive
Important
• In the connections shown above, some cables may not be included with the projector
(see "Package Contents" on page 2). They are commercially available from electronics
stores.
• The connection illustrations above are for reference only. The rear connecting jacks
available on the projector vary with each projector model.
• For detailed connection methods, see pages 13-16.
12
Connecting a computer or monitor
Connecting a computer
The projector provides two VGA input sockets that allow you to connect them to both
IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are
connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
1. Take the supplied VGA cable and connect one end to the D-Sub output socket of
the computer.
2. Connect the other end of the VGA cable to the Computer in 1 or Computer in 2
signal input socket on the projector.
3. If you wish to use the USB display, take a USB cable and connect the A type end
to the USB port of the computer, and the other end to the USB B socket on the
projector.
Important
• Many notebooks do not turn on their external video ports when connected to a
projector. Usually a key combo like FN + F3 or CRT/LCD key turns the external display
on/off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol
on the notebook. Press FN and the labeled function key simultaneously. Refer to your
notebook's documentation to find your notebook's key combination.
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen,
you can connect the Monitor Out signal output socket on the projector to an external
monitor with a VGA cable following the instructions below:
To connect the projector to a monitor:
1. Connect the projector to a computer as described in "Connecting a computer" on
page 13.
2. Take a suitable VGA cable (only one supplied) and connect one end of the cable to
the D-Sub input socket of the video monitor.
Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable
and connect the DVI end of the cable to the DVI input socket of the video monitor.
3. Connect the other end of the cable to the Monitor Out socket on the projector.
Important
• The Monitor Out output only works when Computer in 1 or Computer in 2 is made to the
projector.
13
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one
of the following output sockets:
• Component Video
• S-Video
• Video (composite)
You need only connect the projector to a Video source device using just one of the
above connecting methods, however each provides a different level of video quality.
The method you choose will most likely depend upon the availability of matching
terminals on both the projector and the Video source device as described below:
Best video quality
The best available video connection method is Component Video (not to be confused
with composite Video). Digital TV tuner and DVD players output Component Video
natively, so if available on your devices, this should be your connection method of
choice in preference to (composite) Video.
See "Connecting a Component Video source device" on page 15 for how to connect
the projector to a component video device.
Better video quality
The S-Video method provides a better quality analog video than standard composite
Video. If you have both composite Video and S-Video output terminals on your Video
source device, you should elect to use the S-Video option.
See "Connecting an S-Video source device" on page 15 for how to connect the
projector to an S-Video device.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less
than optimal result from your projector, being the least video quality of the available
methods described here.
See "Connecting a composite Video source device" on page 16 for how to connect the
projector to a composite Video device.
14
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component
Video output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1. Take a VGA (D-Sub) to HDTV (RCA) cable, Component Video cable or a
Component Video to VGA (D-Sub) adaptor and connect the end with 3 RCA type
connectors to the Component Video output sockets of the Video source device.
Match the color of the plugs to the color of the sockets; green to green, blue to
blue, and red to red.
2. If you are using the VGA (D-Sub) to HDTV (RCA) cable and the Component Video
to VGA (D-Sub) adaptor, connect the other end of the cable (with a D-Sub type
connector) to the Computer in 1 or Computer in 2 socket on the projector. If you
are using the Component Video Cable, connect the other end of 3RCA type
connectors to the Y Cb/Pb Cr/Pr sockets on the projector.
Important
• If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned on
and operating correctly. Also check that the signal cables have been connected
correctly.
•
RGB to component adapter (ViewSonic P/N: J2552-0212-00)
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output
socket available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1. Take an S-Video cable and connect one end to the S-Video output socket of the
Video source device.
2. Connect the other end of the S-Video cable to the S-Video socket on the projector.
Important
• If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned on
and operating correctly. Also check that the signal cables have been connected
correctly.
• If you have already made a Component Video connection between the projector and this
S-Video source device using Component Video connections, you need not connect to
this device using an S-Video connection as this makes an unnecessary second
connection of poorer picture quality. See "Connecting Video source devices" on page
14 for details.
15
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite
Video output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite Video source device:
1. Take a Video cable and connect one end to the composite Video output socket of
the Video source device.
2. Connect the other end of the Video cable to the Video socket on the projector.
Important
• If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned on
and operating correctly. Also check that the signal cables have been connected
correctly.
• You need only connect to this device using a composite Video connection if Component
Video and S-Video inputs are unavailable for use. See "Connecting Video source
devices" on page 14 for details.
About the microphone input
• If you wish to use a microphone, connect a 3.5 mini jack cable microphone to the
projector.
• You can use a wireless microphone as long as a wireless module is attached to the
projector's microphone input jack and it works well with the associated devices. To
ensure a quality use of the wireless microphone, it is recommended that your
microphone conforms to the specifications listed in the table below.
Signal
Microphone
Parameter
Transducer Principle
Impedance
Frequency response
Min
300
600
16
Type
Max
1K
16K
Dynamic
ohm
Hz
Operation
Powering On/Off the Projector
Powering On the Projector:
1. Remove the projector lens cap.
2. Complete the AC power cord and peripheral signal cable(s) connections.
3. Press
to turn on the projector.
The projector takes a minute or so to warm up.
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically
detects your source.
• If you are connecting multiple sources to the projector simultaneously, press
SOURCE on the projector to select your desired signal or press your desired
signal key on the remote control.
Warning
• Remove the lens cap first before powering on.
• Never look into the lens when the lamp is on. This can damage your eyes.
• This focal point concentrates high temperature. Do not place any object near it to avoid
possible fire hazard.
Powering Off the Projector:
1. Press
to turn off the projector lamp. You will see a message "Power off" appear
on the screen.
2. Press
again to confirm.
• When the Power LED begins flashing, the projector has entered stand-by mode.
3. Disconnect the AC power cord from the electrical outlet and the projector.
4. Do not turn on the projector right after power off
17
Adjusting the Projector Height
Tilt-adjustment feet
Elevator foot
Elevator button
The projector is equipped with an elevator foot to adjust the image height.
To raise or lower the image:
1. To raise or lower the image, press the elevator button and raise or lower the front
of the projector. Release the button to lock the adjustment.
2. To level the image on the screen, turn the tilt-adjustment feet to fine-tune the
height.
Note
• To avoid damaging the projector, make sure that the elevator foot and tilt-adjustment
feet are fully retracted before placing the projector in its carrying case.
Adjusting the Projector Zoom and Focus
Zoom ring
Focus ring
1. Focus the image by rotating the focus ring. A still image is recommended for focusing.
2. Adjust the image size by sliding the zoom ring.
18
Adjusting Projection Image Size
Refer to the graphic and table below to determine the screen size and projection distance.
Maximum zoom
Minimum zoom
Screen
Center of lens
Vertical offset
Screen size
Diagonal
[inch (cm)]
30 (76)
40 (102)
50 (127)
60 (152)
80 (203)
100 (254)
120 (305)
150 (381)
200 (508)
220 (559)
250 (635)
300 (762)
Projection distance
16 : 9 Screen
Projection distance [inch (m)]
Image height Vertical offset
[inch (cm)]
[inch (cm)]
(min. zoom)
(max. zoom)
35 (0.89)
55 (1.39)
14.7 (37)
5.0 (12.8)
48 (1.21)
74 (1.87)
19.6 (50)
6.7 (17.1)
60 (1.52)
93 (2.35)
24.5 (62)
8.4 (21.4)
72 (1.83)
111 (2.83)
29.4 (75)
10.1 (25.6)
97 (2.46)
149 (3.79)
39.2 (100)
13.5 (34.2)
122 (3.09)
187 (4.75)
49 (125)
16.8 (42.7)
146 (3.72)
224 (5.7)
58.8 (149)
20.2 (51.3)
183 (4.66)
281 (7.14)
73.5 (187)
25.2 (64.1)
246 (6.24)
376 (9.54)
98.1 (249)
33.6 (85.4)
270 (6.87)
413 (10.5)
107.9 (274)
37.0 (94.0)
307 (7.81)
470 (11.94)
122.6 (311)
42.0 (106.8)
369 (9.38)
564 (14.33)
147.1 (374)
50.5 (128.2)
Note
• Position the projector in a horizontal position; other positions can cause heat build-up
and damage to the projector.
• Keep a space of 30 cm or more between the sides of the projector.
• Do not use the projector in a smoky environment. Smoke residue may build-up on
critical parts and damage the projector or its performance.
• Consult with your dealer for special installation such as suspending from a ceiling.
There is 3% tolerance among these numbers due to optical component variations.
It is recommended that if you intend to permanently install the projector, you
should physically test the projection size and distance using the actual projector in
situ before you permanently install it, so as to make allowance for this projector's
optical characteristics. This will help you determine the exact mounting position so
that it best suits your installation location.
19
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings
from being changed accidentally (by children, for example). When the Panel Key
Lock is on, no control keys on the projector will operate except
Power.
1. Press and hold for 3 seconds on the
projector or remote control.
To release panel key lock, press and hold
for 3 seconds on the projector.
HDMI1
HDMI2
Video
Compo
PC
o
er
Auto
Enter
Swap
Default
Important
• Keys on the remote control are still functional when panel key lock is enabled.
• If you press
Power to turn off the projector without disabling panel key lock, the
projector will still be in locked status the next time it is turned on.
20
Menu Operation
The projector has multilingual on-screen display menus that allow you to make image
adjustments and change a variety of settings.
Brightest, Standard, Theater,
Dark Room, DICOM SIM,
User1, User2
Color Mode
Saturation*4
Video Setting
Sharpness*5
Tint*6
Color Temp.
User, LOW, MID, HIGH
Red Gain
0 - 100
Green Gain
0 - 100
Blue Gain
Color
Hue
Saturation
Gain
0 - 100
Red, Green, Blue,
Cyan, Megenta, Yellow
0 - 255
0 - 255
0 - 255
0 - 100
Video/Audio
0 - 200
0 - 100
0 - 100
Overscan
0% - 10%
Noise Reduction
Off, LOW, MID, HIGH
Audio Setting
Computer 1
Audio 1, Audio 2, Audio 3
Video Source
Audio 1, Audio 2, Audio 3
HDMI 1
Audio 1, Audio 2, Audio 3, HDMI
HDMI 2
Audio 1, Audio 2, Audio 3, HDMI
Microphone Volume
0 - 10
Speaker Volume
0 - 20
Mute
21
Audio 1, Audio 2, Audio 3
Computer 2
Setting
Auto Keystone
Keystone
-40 - +40
Aspect Ratio
Auto, 4:3, 16:9,
ANAMORPHIC 1,
ANAMORPHIC 2
Front-Table, Front-Ceiling,
Rear-Table, Rear-Ceiling
Filter Mode*2
High Altitude
Quick Power On
Quick Power Off
DC 12V Trigger
Input Password
Password Delete
Black, Red, Green, Blue,
Cyan, Yellow, Magenta, White
OSD Setting
Top-Left, Bottom-Left, Center,
Top-Right, Bottom-Right
OSD Timeout
OSD Transparency
Off, CC1, CC2, CC3, CC4,
T1, T2, T3, T4
Others
Status Message
Zoom
DCR
Test Pattern
Function*3
Off, PIP, POP
Display Type
Swap
Yes, No
Green Mode
22
20 - 60
0, 10, 20, 30, 40, 50, 60, 70, 80, 90
NetWork
Status
Wired LAN
Disconnect, Connect
On, Off
Default Gateway
DNS
Apply
Status
Wireless LAN
Disconnect, Connect
SSID
Connection Mode
Network Restart
Information
AP, Infrastructure
Yes, No
Input Source
MAC Address
Filter Hours*2
Filter Hours Reset*2
Equivalent Lamp Hours
Equivalent Lamp Hours
Reset
Factory Default
*1 Adjustable range and default setting vary depending on signal type.
*2 This function is only available when the projector is installed an optional filter cover.
*3 The selectable Function list includes Color Mode, Gamma, Overscan, Noise
Reduction, Keystone and Filter Mode.
*4 Saturation is supported under Component, Video and S-Video modes.
*5 Sharpness is supported under HDMI, Component, Video and S-Video modes.
*6 Tint is supported under Component, Video and S-Video modes.
23
How to operate
1. Press MENU on the projector or Menu on the remote control to open the OSD menu.
2. When OSD is displayed, use
/
to select any feature in the main menu.
3. After selecting the desired main menu item, press
4. Use
/
to
select feature setting.
to select the desired item and adjust the settings with
/ .
5. Press MENU on the projector or Menu on the remote control, the screen will return to
the main menu.
6. To exit OSD, press MENU on the projector or Menu on the remote control again. The
OSD menu will close and the projector will automatically save the new settings.
Picture
Color Mode
There are many factory presets optimized for various types of images.
• Brightest:For the brightest environment.
• Standard:For computer or notebook.
• Theater :For home theater.
• Dark Room:For dark environment.
• DICOM SIM: Recommended for DICOM format files in simulation mode.
• User 1:Memorize user 1 defined settings.
• User 2:Memorize user 2 defined settings.
Note
• DCIM SIM option is only for training or reference. It not used for actual diagnosis.
• DICOM represents for the Digital Imaging and Communications in Medicine. This is a
standard created by the American College of Radiology and the National Electrical
Manufacturers Association. This standard specifies the method of digital image data to
be transferred from one system to another.
Brightness
Brighten or darken the image.
Contrast
Set the difference between light and dark areas.
Video Setting
Allow you to enter the Video Setting menu.
• Saturation: Adjust a video image from black and white to fully saturated color.
• Sharpness: Sharpen or soften the image.
• Tint: Shift colors toward red or green.
Color Setting
Adjust the color temperature. At higher temperature the screen looks colder; at lower
temperature, the screen looks warmer. If you select “User”, then you can change the
intensity of each of 3 color (Red, Green, Blue) to customize user color temperature.
User Color
24
User Color provides six sets (RGBCMY) of colors to be adjusted. When you select
each color, you can independently adjust its range and saturation according to your
preference.
Gamma
Effect the represent of dark scenery. With greater gamma value, dark scenery will look
brighter.
Video/Audio
Frequency
Adjust the timing of the projector relative to the computer.
Tracking
Adjust the phase of the projector relative to the computer.
H Position (Horizontal Position)
Adjust the image left or right within the projection area.
V Position (Vertical Position)
Adjust the image up or down within the projection area.
Overscan
Remove noise around the video image.
Noise Reduction
Reduce temporal and/or spatial noise in the image.
Audio Setting
Allow you to enter the Audio Setting menu.
• Computer 1: Select the audio input for Computer in 1 signal.
• When Audio in 1 is turned on, Audio in 2 and Audio in 3 will turn off automatically.
• Computer 2: Select the audio input for Computer in 2 signal.
• When Audio in 2 is turned on, Audio in 1 and Audio in 3 will turn off automatically.
• Video Source: Select the audio input for video source.
• When Audio in 3 is turned on, Audio in 1 and Audio in 2 will turn off automatically.
• HDMI 1: Select the audio input for HDMI 1 signal.
• When HDMI 1 is turned on, Audio in 1, Audio in 2 and Audio in 3 will turn off
automatically.
• HDMI 2: Select the audio input for HDMI 2 signal.
• When HDMI 2 is turned on, Audio in 1, Audio in 2 and Audio in 3 will turn off
automatically.
Microphone Volume
Adjust the microphone’s volume level.
Speaker Volume
Adjust the projector’s volume level.
Mute
Cut off the sound temporarily.
Setting
25
Auto Keystone
Automatically correct distorted images resulting from an angled projection.
Keystone
Manually correct distorted images resulting from an angled projection.
• When adjusting the Keystone, Auto Keystone will be set at "Off" automatically.
Aspect Ratio
Select how the picture fits on the screen:
• Auto:Scales an image proportionally to fit the projector's native resolution in its
horizontal or vertical width.
• 4:3:Scales an image so that it is displayed in the center of the screen with a 4:3
aspect ratio.
• 16:9:Scales an image so that it is displayed in the center of the screen with a 16:9
aspect ratio.
• ANAMORPHIC 1: Scale an image so that it is displayed in the center of the screen
with a 1.85:1 aspect ratio.
• ANAMORPHIC 2: Scale an image so that it is displayed in the center of the screen
with a 2.35:1 aspect ratio.
Projection
Adjust the picture to match the orientation of the projector: upright or upside-down, in
front of or behind the screen. Invert or reverse the image accordingly.
Power Saving
If the input source is not detected and no operation is performed for a specific period
of time, projector will automatically turn off.
Auto Source
Automatically scan through all the input source.
Signal Type
Specify the source to the Computer in 1/Computer in 2 terminal that you wish to
project.
• Auto: Automatically detect the input signal type from Computer in 1 and Computer in 2
terminals.
• RGB: For VGA signal
• YCbCr:For component signal
ECO Mode
Use this function to dim the projector lamp light output which will lower power
consumption and increase lamp life.
• This function will be unavailable when the DCR function is on.
Filter Mode
Use this function to activate filter mode after the projector is installed an optional filter
cover.
High Altitude
Use this function to allow the fans operates at full speed continuously to achieve
proper high altitude cooling of the projector.
Quick Power On
26
• On: The projector will turn on in 3 seconds.
• Off: The projector will turn on following normal power on procedure.
Quick Power Off
• On: The projector will directly shut down without cooling procedure.
• Off: The projector will shut down following normal cooling procedure.
DC 12V Trigger
1. When Green Mode is off and the projector is under standby mode, you can enable
or disable to trigger external devices such as anelectric screen.
2. When Green Mode is on and the projector is under standby mode, DC 12V will not
trigger the screen no matter you set to on or off.
3. When the projector is under normal projection, DC 12V will always trigger the
screen no matter you set to on or off.
Option
Password
Set or delete the password. When the password function is added, image projection
will require to input the preset password when turning on the projector.
Blank Screen
Blank the screen temporarily, and select the screen color when this function is active.
OSD Setting
Allow you to enter the OSD Setting menu.
• Menu Position: Choose the menu location on the display screen.
• OSD Timeout: Duration of OSD menu display countly starts (at idle state by
second).
• OSD Transparency: Select to change the transparency level of the OSD
background.
Closed Caption
Enable or disable closed captions by selecting CC1 (closed caption1, the most
common channel), CC2, CC3, CC4, T1, T2,T3, T4 or OFF.
Others
Allow you to enter the Others menu.
• Message: Enable or disable the message box at the right bottom of the screen.
• Zoom: Zoom in and out the images.
• DCR (Dynamic Contrast Ratio): Enable DCR will further enhance contrast ratio by
darkening the black scenes. Disable DCR will resume to normal contrast
performance. DCR will impact lamp life and system noise performance.
• Test Pattern: Display embedded test pattern.
Function
Allow user to define a short cut key on the remote control, and the function item is
selected in OSD menu.
Display Type
Allow user to select PIP (Picture in Picture) screen, POP (Picture on Picture) screen
or disable PIP/POP function.
27
Swap
Allow user to swap input source in PIP or POP image.
Green Mode
Enable this function when power consumption is under 0.5W.
Network
Wired LAN
Allow you to configure the wired LAN settings.
• Status: Display the projector’s status.
• DHCP: Abbreviation for Dynamic Host Configuration Protocol. This protocol
automatically assigns IP Address to networked devices.
• When the “DHCP” sets to “On”, it takes some time to obtain IP address from
DHCP server.
• When the "DHCP" sets to "Off", that means user will set IP address by manually.
• IP Address: Numerical address to identify networked computers. This function can
only be used when DHCP is set to Off.
• The IP Address is the number that identifies this projector on the network. You
cannot have two devices with the same IP Address on the same network.
• The IP Address “0.0.0.0” is prohibited.
• Subnet Mask: A numeric value to define the number of bits used for a network
address of a divided network (or subnet) in an IP Address. This function can only
be used when DHCP is set to Off.
• The Subnet Mask “0.0.0.0” is prohibited.
• Default Gateway: A server (or router) to communicate across networks (subnets)
that are divided by Subnet Mask. This function can only be used when DHCP is set
to Off.
• DNS: Setup DNS server address when DHCP is disable.
• Apply: Save and execute the wired LAN settings.
Wirless LAN
Allow you to configure the wireless LAN settings.
• Status: Display the projector’s status.
• SSID: Display the projector’s SSID information.
• IP Address: Numerical address to identify networked computers. This function can
only be used when DHCP is set to Off.
• The IP Address is the number that identifies this projector on the network. You
cannot have two devices with the same IP Address on the same network.
• The IP Address “0.0.0.0” is prohibited.
• Connection Mode: Methods for connecting to wireless networks with Wi-Fi enabled
devices.
Network Restart
Restore network settings to default.
The password for web administrator and vsPresenter will be reset to default “admin”.
Information
28
Input Source
Display the current input source.
Resolution
Display current input source resolution.
H. Frequency
Display current image horizontal frequency.
V. Frequency
Display current image vertical frequency.
MAC Address
Abbreviation for Media Access Control Address. MAC Address is a unique ID number
assigned to each network adapter.
Filter Hours
Display the filter’s elapsed operating time (in hours).
• When Filter Mode is turned on, the Filter Hours also turns on automatically.
Filter Hours Reset
Reset the filter Hour to 0 hours.
Equivalent Lamp Hours
Display the lamp’s elapsed operating time (in hours).
Equivalent Lamp Hours Reset
Reset the lamp Hour to 0 hours.
Factory Default
Restore settings to factory default.
The following settings will still remain: MAC Address, Language, Projection, High
Altitude, Filter Mode, Password, Lamp Hours, Filter Hours, Auto Keystone, Keystone.
Language
Select the language used by the on-screen menu.
29
Controlling the projector through a LAN environment
You can manage and control the projector from one or more remote computers when
they are properly connected to the same local area network.
Wired connection
Internet
IP Router
If you are in a DHCP environment:
1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the
projector and the other end to the RJ45 port on your Ethernet or router.
2. Press MENU/EXIT on the projector or Menu on the remote control and then press
/ until the Network menu is highlighted.
3. Highlight Wired LAN and press ENTER on the projector or Enter on the remote
control.
4. Make sure the Status is Connect.
5. Press
to highlight DHCP and press
/
to select On.
6. Press to highlight Apply and press ENTER on the projector or Enter on the
remote control.
7. Please wait for around 15 - 20 seconds, and then re-enter the Wired LAN page.
The IP Address, Subnet Mask, Default Gateway, and DNS settings will be
displayed. Note down the IP address displayed in the IP Address row.
Important
• If the Projector IP Address still does not appear, contact your network administrator.
• If the RJ45 cables are not properly connected, the IP Address, Subnet Mask, Default
Gateway, and DNS settings will display 0.0.0.0. Make sure the cables are properly
connected and perform the procedures above again.
• If you wish to connect to the projector in its standby mode, be sure you have selected
RJ45 and obtained the IP Address, Subnet Mask, Default Gateway, and DNS information
when the projector is on.
If you are in a non-DHCP environment:
1. Repeat steps 1-4 above.
2. Press
to highlight DHCP and press
/
to select Off.
3. Contact your ITS administrator for information on the IP Address, Subnet Mask,
Default Gateway, and DNS settings.
4. Press to select the item you want to modify and press ENTER on the projector
or Enter on the remote control.
30
5. Press
/
to move the cursor and the enter the value.
6. To save the settings, press ENTER on the projector or Enter on the remote
control. If you do not want to save the settings, press MENU/EXIT on the projector
or Menu on the remote control.
7. Press to highlight Apply and press ENTER on the projector or Enter on the
remote control.
Important
• If the RJ45 cables are not properly connected, the IP Address, Subnet Mask, Default
Gateway, and DNS settings will display 0.0.0.0. Make sure the cables are properly
connected and perform the procedures above again.
• If you wish to connect to the projector in its standby mode, be sure you have selected
RJ45 and obtained the IP Address, Subnet Mask, Default Gateway, and DNS information
when the projector is on.
31
Wireless connection
ViewSonic wireless dongle
To connect to the projector wirelessly, you have to plug a ViewSonic wireless dongle
(optional) to the USB Type A connector on the projector, and then only a few OSD
configuration steps are required.
1. Make sure the projector is turned on.
2. Press MENU/EXIT on the projector or Menu on the remote control and then press
/ until the Network menu is highlighted.
3. Highlight Wireless LAN and press ENTER on the projector or Enter on the remote
control.
4. Make sure the Status is Connect.
5. Make sure the SSID information is displayed.
6. In AP mode, you need to use your computer’s wireless connection utility to search
the projector’s SSID and connect to it. Then you can search the projector with
vsPresenter. To use Infrastructure mode, you should connect both your computer
and projector to the same AP router and make connections with the IP address.
About AP and Infrastructure modes
In AP mode, you need to use your computer's wireless connection utility to search for
the projector's SSID and connect to it. Then you can search for the projector with
vsPresenter.
In Infrastructure mode, you should connect both your computer and projector to the
same AP router and make connections with the IP address.
The following diagram describes how to access the Internet in AP and Infrastructure
modes.
(AP mode)
(Infrastructure mode)
Internet
Internet
Important
• If you need more information about AP and Infrastructure modes, please refer to user
documentations for Wireless Routers which are usually available on 3C stores.
32
Controlling the projector through a web browser
Once you have the correct IP address for the projector and the projector is on or in
standby mode, you can use any computer that is on the same local area network to
control the projector.
Important
• If you are using Microsoft Internet Explorer, make sure it is version 7.0 or higher.
• The screenshots in this manual are for reference only, and may differ from the actual
design.
1. Enter the address of the projector in the address bar of your browser and press
Enter.
2. The main page of the ViewSonic webpage control system appears.
3
5
6
4
3. To change the language for the web pages, click the down arrow to reveal a drop
down list and select a desired language.
4. To download vsPresenter, click Download. See "Displaying images through
vsPresenter" on page 38 for details.
5. The Crestron (eControl) page displays the Crestron eControl user interface. See
"About Crestron control" on page 34 for details.
6. To have access to the Admin page, you need to enter a password. The default
password is “admin”.
33
• System Status: Displays the system information.
• General Setup: Allows you to turn on/off the projector, switch the input signal for
the projector, and change the password for the Administrator page.
• Picture Setup/Image Setup: Provides some OSD menu items for adjusting the
projected pictures. See "Menu Operation" on page 21 for details.
• Alert Setup/Mail Setup: Allows you to setup the mail server and send system
error messages to your ITS administrator.
• Network Setup: Provides wired and wireless network settings.
• Reset to Default: Allows you to restore the device to the factory default settings.
About Crestron control
The Crestron (eControl) page displays the Crestron eControl user interface. The
eControl page provides a variety of virtual keys to control the projector or adjust the
projected pictures.
i
i
ii
You can press
W/X to reveal
more buttons.
i
iii
i.
These buttons function the same as the ones on the OSD menus or remote
control.
ii. To switch between input signals, click on your desired signal.
iii. To change the language for the Crestron page, click the down arrow to reveal a
drop down list and select a desired language.
Important
• The Menu button can also be used to go back to previous OSD menus, exit and save
menu settings.
• The source list varies according to the connectors available on the projector.
• When you use the projector control panel or remote control to change the OSD menu
settings, it may take a while for the web browser to synchronize these changes with the
projector.
34
The tools page allows you to manage the projector, configure the LAN control settings
and secure access of remote network operation on this projector.
iv
vi
v
vii
viii
ix
x
iv. This section is only used with the Crestron Control System. Please contact
Creston or refer to its user manual for setup information.
v. Click the down arrow to reveal a drop down list and select a default language.
vi. You can name the projector, keep track of its location and the person in charge
of it.
vii. You can adjust the LAN Control Settings.
viii.Once set, access to the remote network operation on this projector has been
password-protected.
ix. Once set, access to the tools page has been password-protected.
Important
• To prevent errors, only input the English alphabet and digits on the tools page.
• After making the adjustments, press the Send button and the data will be saved for the
projector.
x. Press Exit to go back to the remote network operation page.
35
Please pay attention to the limitation of input length (including space and other
punctuation keys) in the list blow:
Category Item
Input Length
Maximum Number of
Characters
Crestron Control
IP Address
15
IP ID
2
Port
5
Projector
Projector Name
10
Location
9
Assigned To
9
Network Configuration
DHCP (Enabled)
(N/A)
IP Address
15
Subnet Mask
15
Default Gateway
15
DNS Server
15
User Password
Enabled
(N/A)
New Password
20
Confirm
2
Admin Password
Enabled
(N/A)
New Password
20
Confirm
20
The info page displays the information and status of this projector.
Press Exit to go
back to the remote
network operation
page.
After pressing the button “Help”, the Help Desk window will appear in the upper right
corner of the screen. You will be able to deliver messages to RoomView software
administrators/users who connect to the same local area network.
36
Important
• Please only deliver the messages in English letters and digits.
For more information, visit http://www.crestron.com & www.crestron.com/getroomview.
**Crestron RoomView
On the "Edit Room" page, enter the IP Address (or hostname) as shown on the
projector's on-screen display (OSD) menu, and "05" for IPID, "41794" for the reserved
Crestron control port.
About Crestron RoomView setting and command method, please access below
website to get RoomView User Guide and more information:
http://www.crestron.com/features/
roomview_connected_embedded_projectors_devices/resources.asp
37
Displaying images through vsPresenter
Downloading and installing vsPresenter
The vsPresenter is an application running on the host PC. It helps connect your
computer to an available network projector and transfer the desktop content to the
network projector via local network connection.
1. Enter the main page of Network Control. See steps 1-2 on page 33 for details.
2. Download vsPresenter.
3. When the download is complete, install the software to your computer by clicking
the exe file. Follow the on-screen instructions to complete the installation.
4. Launch vsPresenter.
Using vsPresenter
1
7
2
6
3
4 &5
1. The Search page allows you to search and connect to a projector.
i.
To connect to a projector, select Directly then type the projector IP address and
click Connect.
ii. To search for projectors, simply click Search to list all the projectors on the
same local area network. Click the desired projectors in the Search result list,
and click Connect directly. You can also type a desired projector name and
click Search.
iii. You can link to the ViewSonic webpage control system on page 33.
• If you are the first time user, choose your identity as a Normal user or
Administrator. Both require no password. But if you choose to be an
Administrator, you have the authority to set a password for connecting to the
projector. That password should be kept and used next when you try to connect
to the same projector.
• If there are multiple computers connected to the projector, you can decide a
display zone by clicking 1, 2, 3, 4, L, R, All, or Background.
38
2. If you want to freeze the projected image on the screen, press . Any further
movements will be not been seen on the screen until is pressed.
3. You can choose a capture mode from here.
i. To display a full screen, click FullScreen.
ii. To display a partial screen, click FixedSize. A square appears on your screen.
You can place it where you want to project.
iii. If you wish to change the square, click Alterable.
4. The Basic Setting page allows you to configure vsPresenter.
i.
ii.
iii.
iv.
v.
To change the vsPresenter interface language, click the down arrow to reveal a
drop-down list and select a desired language. Click Apply.
Users can change the size parameters of the frame in FixedSize capture mode
by modifying width and height on this page and click Apply to make changes
take effect.
User can use the mirror driver for presenter capture image, if the system has
installed the mirror driver.
To allow notification messages to appear, click Yes. Click Apply.
The Software Information is available on this page.
39
5. The Advanced Setting page allows you to configure vsPresenter.
i.
To adjust the image quality, click the down arrow to reveal a drop-down list and
select a desired quality level. The higher image quality you select, the higher
network transfer speed is required. Select a YUV sample format between
YUV444 and YUV420. Compared to format YUV420, format YUV 444 provides
better effect but may slow the transport and playing speed. Click Apply after
your selections.
ii. To adjust the capture rate, move the slide bar. The network bandwidth may also
affect the performance.
iii. Network port setting for fixed or manual type.
6. You can manage the connected projectors listed under Device Management.
• Under a conference mode:
1. Only the administrator can take control.
2. A projector can display up to 4 computer screens.
• You can set the name of your computer under vsPresenter Management.
40
• For details about the icons, please see the following:
Icon
Description
Icon
Description
You are a normal user and
Disconnects from the projector.
have no access to change the
password.
You are an administrator and
Opens the web page of the
have authority to change the
Network Control.
password.
You are the user of the
There is another user of the
projector.
projector.
You are an administrator of
You are a normal user of the
projector.
the projector.
Sets a display zone for the projector.
7. Disconnect
To disconnect from the projector(s), click the Disconnect icon.
Important
• Be sure to turn off other virtual network control programs before using vsPresenter.
41
Displaying pictures with a USB storage device
The projector is built-in an application which can display packaged images on a USB
storage device. It can eliminate the need for a computer source.
The projector supports the following image formats:
File format
Maximum pixel size
JPEG
8000 x 8000
GIF/TIFF/PNG/BMP
1280 x 800
• Progressive JPEG files are not supported.
• Some JPEG files may not be displayed clearly.
To display the images on a USB storage device:
1. Plug the USB storage device into the USB A socket.
2. The projector automatically displays the main screen. Or your can manually select
USB A from the source selection bar.
3. Press ENTER on the projector or Enter on the remote control to display the
content of your USB storage device.
4. Folders and supported files are represented in thumbnail mode.
• To scroll through the thumbnails, use the four directional arrow keys.
• To open a folder/file, press ENTER or Enter.
• To go back to the previous screen, select the thumbnail with an up arrow in the
top right corner of the screen, and press ENTER or Enter.
• To obtain more functions, press MENU to open the menu. To leave the menu,
press ENTER or Enter again.
When viewing thumbnails
• Next: Selects the next folder/image.
• Previous: Selects the previous folder/image.
• Thumbnail/Full Screen/SlideShow: Displays the selected image in thumbnail/
Full Screen/SlideShow mode.
42
• NameOrder/ExtendOrder/SizeOrder/TimeOrder: Sets the images to be
displayed in the order of filenames, filename extension, file sizes, or time the
photos were taken.
• EXIF OFF/EXIF ON: Sets whether to display the image in EXIF format.
• FileName ON/FileName OFF: Sets whether to display the filename.
When viewing slide shows
•
•
•
•
•
Stop: Stops the slide show.
NEXT: Selects the next image.
Previous: Selects the previous image.
Delay 3/Deplay 4/Deplay 5: Sets the interval between the two images display.
Slide Right/Slide Up/Right Down/XLines/YLines/Blocks: Sets the way the slide
show is displayed.
• Repeat On/Off: Sets whether to repeat the slide shows.
When viewing full screen images
• Thumbnail/Full Screen/SlideShow: Displays the selected image in thumbnail/
Full Screen/SlideShow mode.
• Best Fit/Actual Size: Sets the display size of the image.
• EXIFDisp OFF/EXIFDisp ON: Sets whether to display the EXIF data.
• + 90deg: Rotates the image 90 degrees clockwise.
• -90deg: Rotates the image 90 degrees counterclockwise.
• USB 2.0 compliant USB storage media (Mass Storage Class) is supported.
43
• It is strongly recommended to use an AC power adaptor with the USB hard disk.
• The following formats are recommended for the USB hard disk: FAT12/FAT16/
FAT32 (NTFS format is not supported).
• Some USB flash drives may not work correctly with the projector.
• The security USB flash drive is not supported.
• Do not connect any apparatus other than USB storage devices and other
equipment for battery charge through USB. It may caused malfunction.
• The projector plays up to 200 files in a folder.
• The filenames are displayed in the following order: symbols, digits, letters.
• The projector can display the filenames up to 16 characters including the file
extension.
• The application is best to display the filenames in English. If the files are named in
other languages, the filenames may not show properly, but the content still can be
displayed.
• Folders in the USB storage device can be recognized up to 3 layers. The priority of
thumbnail display for image files is as follows:
A : Currect directory: A
File display priority in folder:
A > B > C > D > E > F.
Folder G: Cannot be displayed because it is in the
4th layer.
B : Folder B
D : Folder D
E : Folder E
G : Folder G
C : Folder C
F : Folder F
• Response time may vary depending on image contents when switching pages,
loading and playing files.
44
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt
or spots will project on the screen and diminish image quality. If any other parts need
replacing, contact your dealer or qualified service personnel. When cleaning any part
of the projector, always switch off and unplug the projector first.
Warning
• Never open any of the covers on the projector. Dangerous electrical voltages inside the
projector can cause severe injury. Do not attempt to service this product yourself. Refer
all servicing to qualified service personnel.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Projector Housing
Gently wipe with a soft cloth. If dirt and stains are not easily removed, use a soft cloth
damped with water, or water and neutral detergent, and wipe dry with a soft, dry cloth.
Cleaning the Filter Cover
The filter cover, which is located at the side of the projector, should be cleaned after
every 100 hours of use. If it is not cleaned periodically, it can become clogged with
dust and prevent the projector from being ventilated properly. This can cause over
heating and damage the projector.
To clean the filter cover:
1. Switch the projector off and unplug the AC
power cord from the wall socket.
2. Remove the filter cover as the illustration
shown.
3. Clean the filter cover.
• To clean the filter cover, you are advised
to use a small vacuum cleaner designed
for computers and other office
equipment.
• If the filter cover is torn, replace it.
4. Replace the filter cover.
5. Attach the filter cover.
6. Plug the power back into the projector.
Note
• Turn off the projector and remove the AC power cord from the power outlet before
beginning maintenance work.
• Make sure the lens is cool before cleaning.
• Do not use detergents or chemicals other than those noted above. Do not use benzene
or thinners.
• Do not use chemical sprays.
45
• Use a soft cloth or lens paper only.
Replacing the Lamp
As the projector operates over time, the brightness of the projector lamp gradually
decreases and the lamp becomes more susceptible to breakage. We recommend
replacing the lamp if a warning message is displayed. Do not attempt to replace the
lamp yourself. Contact the qualified service personnel for replacement.
Type number: RLC-076
Note
• The lamp is extremely hot right after turning off the projector. If you touch the lamp, you
may scald your finger. When you replace the lamp, wait for at least 45 minutes for the
lamp to cool down.
• Do not touch the lamp glass at any time. The lamp may explode due to improper
handling, including the touching of the lamp glass.
• Lamp lifetime may differ from lamp to lamp and according to the environment of use.
There is no guarantee of the same lifetime for each lamp. Some lamps may fail or
terminate their lifetime in a shorter period of time than other similar lamps.
• A lamp may explode as a result of vibration, shock or degradation as a result of hours of
use as its lifetime draws to an end. Risk of explosion may differ according to the
environment or conditions in which the projector and lamp are being used.
• Wear protective gloves and eyeglasses when fixing or detaching the lamp.
• Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least for 5
minutes to turn off the projector after powering on.
• Do not operate the lamp in proximity to paper, cloth, or other combustible material nor
cover it with such materials.
• Do not operate the lamp in an atmosphere containing an inflammable substance, such
as thinner.
• Thoroughly ventilate the area or the room when operating the lamp in an oxygen
atmosphere (in the air). If ozone is inhaled, it could cause headaches, nausea, dizziness,
and other symptoms.
• The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury inside the
lamp will be exposed. Leave the area immediately if the lamp shatters while being
operated and ventilate the area for at least 30 minutes in order to avoid the inhalation of
mercury fumes. Otherwise it could be harmful to user’s health.
46
1. Turn off the projector.
2. If the projector is installed in a ceiling mount, remove it
3. Unplug the power cord.
4. Loosen the screw in the side of the lamp cover and remove the cover.
5. Remove the screws from the lamp module, raise the handle, and lift out the
module.
6. Insert the new lamp module into the projector and tighten the screws.
7. Replace the lamp cover and tighten the screw.
8. Turn on the projector. If the lamp does not turn on after the warm-up period, try
reinstalling the lamp.
9. Reset the lamp hour. Refer to the “Information” menu.
Note
• Dispose the used lamp according to local regulations.
• Ensure that screws are tightened properly. Screws not tightened fully may result in
injury or accidents.
• Since the lamp is made of glass, do not drop the unit and do not scratch the glass.
• Do not reuse the old lamp. This could cause the lamp to explode.
• Be sure to turn off the projector and unplug the AC power cord before replacing the
lamp.
• Do not use the projector with the lamp cover removed.
47
Specifications
Display system
Resolution
Zoom
F/No.
Focal length
Screen size
Lamp
Input terminal
Output terminal
Control terminal
Speaker
Video compatibility
Single 0.65" DLP panel
1080p (1920 × 1080 pixels)
1.5X
2.41 - 2.97
20.72 - 31mm
30” - 300”
350W
D-Sub 15-pin x 2, S-Video x 1, Video x 1, Audio signal input
(3.5 mm stereo mini jack) x 2, HDMI x 2, Component RCA
jack x 1, RCA audio jack (L/R) x 1, 3.5 mm Mic input x1,
USB A type x1 (supports firmware update, USB flash drive
display and wireless dongle for USB display), USB mini-B
type x1 (supports USB display)
D-Sub 15 pin x 1, Audio signal output (3.5 mm stereo mini
jack) x 1
RS-232 x 1, 12-Vdc trigger output x 1, RJ45 x 1
10 watt x 2
NTSC, NTSC 4.43
PAL, PAL-N, PAL M
SECAM, HDTV (480i/p, 576p, 720p, 1080i/p), Composite
video
Scanning frequency
Horizontal frequency
Vertical frequency
Environment
31 - 100 KHz
50 - 85 Hz
Operating:
Temperature: 0°C to 40°C
Humidity: 10%-80%
Storage:
Temperature: -20°C to 60°C
Humidity: 5%-85%
Power requirement
AC 100-240 V, 50 - 60 Hz, 4.3A
Power consumption
450 W
Dimension (W x D x H) 335 x 267 x 132 mm
Weight
3.86 kg (8.5 lbs)
Note: Design and Specifications are subject to change without prior notice.
48
Dimensions
335 mm (W) x 267 mm (D) x 132 mm (H)
335
64.5
267
132
84.9
Ceiling mount installation
227
Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)
Unit: mm
174
103
49
Appendix
LED Indicator Messages
LED type
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Color
Blue
Red
Red
Blue
Red
Red
Blue
Red
Red
Blue
Red
Red
Blue
Red
Red
Blue
Red
Red
Blue
Red
Status
Solid
Off
Off
Flash
Off
Off
Solid
Off
Off
Solid
Off
Off
Flash
Off
Off
Solid
Solid
Flash
Solid
Solid
Temp LED
Red
Off
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Blue
Red
Red
Blue
Red
Red
Blue
Red
Red
Solid
Flash
Off
Off
Solid
Solid
Flash
Off
Off
Meaning
Standby mode when green mode is turned
on.
Standby mode when green mode is turned
off.
Powering up
Normal operation
Powering down
(The projector needs to cool for 35 seconds
after the power is turned off.)
The projector system has some problems
with its fans, so the projector cannot start up.
The lamp has reached its end of life and must
be changed soon. The lamp will continue to
opearate until it failes. Change the lamp. If
the lamp is off, then the ballast will become
malfuction.
Temperature is too high. The lamp will turn
off. The fan motor is cooling the lamp.
The lamp ignition failied. If temperature is too
high, the fans will cool the lamp.
The projector needs to cool for 90 seconds
after the power is turned off. If you try to restart the projector, it will shut down again.
50
Compatibility Modes
Computer:
Compatibility
Resolution
VGA
640 x 480
SVGA
800 x 600
XGA
1024 x 768
SXGA
1280 x 1024
UXGA
Mac 13
Mac 16
Mac 19
1080i30
1080i25
480p
576p
720p60
720p50
1080p60
1080p50
1600 x 1200
640 x 480
832 x 624
1024 x 768
1920 x 1080
1920 x 1080
720 x 480
720 x 576
1280 x 720
1280 x 720
1920 x 1080
1920 x 1080
H-Sync [KHz]
24.69
31.5
37.9
37.5
43.3
30.99
35.2
37.9
48.1
46.9
53.7
39.63
48.4
56.5
60
64
80
47.7
35
49.72
60.24
33.75
28.13
31.47
31.25
45
37.5
67.5
56.25
V-Sync [Hz]
50
60
72
75
85
50
56
60
72
75
85
50
60
70
75
60
75
60
67
75
75
60
50
59.94
50
60
50
60
50
Video:
Compatibility
1080p
1080p
1080i
1080i
720p
720p
576p
576i
480p
480i
Resolution
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1280 x 720
1280 x 720
720 x 576
720 x 576
720 x 480
720 x 480
H-Sync [KHz]
67.5
56.3
33.8
28.1
45
37.5
31.3
15.6
31.5
15.8
51
V-Sync [Hz]
60
50
60
50
60
50
50
50
60
60
Troubleshooting
Refer to the symptoms and measures listed below before sending the projector for
repairs. If the problem persists, contact your local reseller or service center. Please
refer to "LED Indicator Messages" as well.
Start-up problems
If no lights turn on:
• Be sure that the power cord is securely connected to the projector and the other end is
plugged into an outlet with power.
• Press the power button again.
• Unplug the power cord and wait for a short while, then plug it in and press the power
button again.
Image problems
If the searching source is displayed:
• Press SOURCE on the projector or Source on the remote control to select an
active input source.
• Be sure the external source is turned on and connected.
• For a computer connection, ensure your notebook computer’s external video port is
turned on. Refer to the computer manual.
If the image is out of focus:
• Be sure the lens cover is removed.
• While displaying the on-screen menu, adjust the focus ring. (The image size should
not change; if it does, you are adjusting the zoom, not the focus.)
• Check the projection lens to see if it needs cleaning.
If the image is flickering or unstable for a computer connection:
• Press Auto on the remote control.
• Press MENU on the projector or Menu on the remote control, go to Video/Audio and
adjust Frequency or Tracking.
Remote control problems
If the remote control does not operate:
• Be sure nothing is blocking the remote control receiver on the front of the projector.
Use the remote control within the effective range.
• Aim the remote control at the screen or at the front or back of the projector.
• Move the remote control so it is more directly in front of or behind the projector and
not as far to the side.
52
RS-232 Command and Configuration
D-Sub 9 pin
1
2
3
4
5
6
7
8
9
Wire List
1 CD
RXD
TXD
DTR
GND
DSR
RTS
CTS
RI
C1
1
2
3
4
5
6
7
8
9
SHELL
Baud Rate
Data Length
Parity Check
Stop Bit
Flow Control
COLOR
Black
Brown
Red
Orange
Yellow
Green
Blue
Purple
White
DW
19200 bps
8 bit
None
1 bit
None
POWER ON / POWER OFF
POWER ON
BE,EF,10,05,00,C6,FF,11,11,01,00,01,00
POWER OFF
BE,EF,02,06,00,6D,D2,34,00,00,00,00,00
Computer 1
BE,EF,02,06,00,BC,D3,35,00,00,00,00,00
Computer 2
BE,EF,02,06,00,8F,D3,36,00,00,00,00,00
COMPONENT
BE,EF,02,06,00,5E,D2,37,00,00,00,00,00
COMPOSITE
BE,EF,02,06,00,A1,D2,38,00,00,00,00,00
S-VIDEO
BE,EF,02,06,00,70,D3,39,00,00,00,00,00
HDMI 1
BE,EF,02,06,00,43,D3,3A,00,00,00,00,00
HDMI 2
BE,EF,02,06,00,92,D2,3B,00,00,00,00,00
USB A
BE,EF,02,06,00,25,D3,3C,00,00,00,00,00
USB B
BE,EF,02,06,00,F4,D2,3D,00,00,00,00,00
LAN
BE,EF,02,06,00,8A,DF,63,00,00,00,00,00
SOURCE SELECT
QUICK KEY
MENU
BE,EF,02,06,00,C8,D7,01,00,00,00,00,00
UP
BE,EF,02,06,00,FB,D7,02,00,00,00,00,00
DOWN
BE,EF,02,06,00,2A,D6,03,00,00,00,00,00
LEFT
BE,EF,02,06,00,9D,D7,04,00,00,00,00,00
RIGHT
BE,EF,02,06,00,4C,D6,05,00,00,00,00,00
ENTER
BE,EF,02,06,00,E6,D6,0F,00,00,00,00,00
53
C2
1
3
2
6
5
4
8
7
9
SHELL
RESYNC
BE,EF,02,06,00,F2,D5,1B,00,00,00,00,00
ASPECT
BE,EF,02,06,00,C7,D2,3E,00,00,00,00,00
MUTE
BE,EF,02,06,00,16,D3,3F,00,00,00,00,00
FREEZE
BE,EF,02,06,00,D9,D8,40,00,00,00,00,00
BLANK
BE,EF,02,06,00,08,D9,41,00,00,00,00,00
SOURCE
BE,EF,02,06,00,7F,D6,06,00,00,00,00,00
OTHER FUNCTION
DCR ON
BE,EF,02,06,00,EA,D8,43,00,00,00,00,00
DCR OFF
BE,EF,02,06,00,5D,D9,44,00,00,00,00,00
ECO ON
BE,EF,02,06,00,8C,D8,45,00,00,00,00,00
ECO OFF
BE,EF,02,06,00,BF,D8,46,00,00,00,00,00
VOLUME INC
BE,EF,02,06,00,6E,D9,47,00,00,00,00,00
VOLUME DEC
BE,EF,02,06,00,91,D9,48,00,00,00,00,00
KEYSTONE INC
BE,EF,02,06,00,40,D8,49,00,00,00,00,00
KEYSTONE DEC
BE,EF,02,06,00,73,D8,4A,00,00,00,00,00
FACTORY RESET
BE,EF,02,06,00,A2,D9,4B,00,00,00,00,00
LAMP HOURS RESET
BE,EF,02,06,00,15,D8,4C,00,00,00,00,00
FILTER HOURS RESET
BE,EF,02,06,00,C4,D9,4D,00,00,00,00,00
54
IR Control Code
System Code: 83F4
Format : NEC
87
HDMI1
HDMI2
Video
Compo
6D
PC
67
6E
6F
08
82
Auto
Enter
83
08
81
85
84
Swap
Default
55
8D
02
01
62
04
09
0B
03
06
8E
63
8F
05
Customer Support
For technical support or product service, see the table below or contact your reseller.
Note : You will need the product serial number.
T = Telephone
Email
F = FAX
AUS= 1800 880 818
Australia/New Zealand
www.viewsonic.com.au
service@au.viewsonic.com
NZ= 0800 008 822
T (Toll-Free)= 1-866-463-4775
Canada
www.viewsonic.com
T (Toll)= 1-424-233-2533
service.ca@viewsonic.com
F= 1-909-468-3757
Europe
www.viewsoniceurope.com www.viewsoniceurope.com/uk/support/call-desk/
Hong Kong
www.hk.viewsonic.com
T= 852 3102 2900
service@hk.viewsonic.com
India
www.in.viewsonic.com
T= 1800 266 0101
service@in.viewsonic.com
Korea
www.kr.viewsonic.com
T= 080 333 2131
service@kr.viewsonic.com
Latin America (Argentina) www.viewsonic.com/la/
T= 0800-4441185
soporte@viewsonic.com
Latin America (Chile)
www.viewsonic.com/la/
T= 1230-020-7975
soporte@viewsonic.com
Latin America
www.viewsonic.com/la/
T= 01800-9-157235
soporte@viewsonic.com
(Columbia)
Latin America (Mexico)
www.viewsonic.com/la/
T= 001-8882328722
soporte@viewsonic.com
Renta y Datos, 29 SUR 721, COL. LA PAZ, 72160 PUEBLA, PUE. Tel: 01.222.891.55.77 CON 10 LINEAS
Electroser, Av Reforma No. 403Gx39 y 41, 97000 Mérida, Yucatán. Tel: 01.999.925.19.16
Other places please refer to http://www.viewsonic.com/la/soporte/index.htm#Mexico
Latin America (Peru)
www.viewsonic.com/la/
T= 0800-54565
soporte@viewsonic.com
Macau
www.hk.viewsonic.com
T= 853 2870 0303
service@hk.viewsonic.com
Middle East
ap.viewsonic.com/me/
Contact your reseller
service@ap.viewsonic.com
T= 1-800-688-6688 (English)
service.us@viewsonic.com
Puerto Rico & Virgin
www.viewsonic.com
T= 1-866-379-1304 (Spanish)
Islands
soporte@viewsonic.com
F= 1-909-468-3757
Singapore/Malaysia/
www.viewsonic.com.sg
T= 65 6461 6044
service@sg.viewsonic.com
Thailand
South Africa
ap.viewsonic.com/za/
Contact your reseller
service@ap.viewsonic.com
T (Toll-Free)= 1-800-688-6688
United States
www.viewsonic.com
T (Toll)= 1-424-233-2530
service.us@viewsonic.com
F= 1-909-468-3757
Country/Region
Website
56
Limited Warranty
ViewSonic® Projector
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and
workmanship, under normal use, during the warranty period. If a product proves to
be defective in material or workmanship during the warranty period, ViewSonic will,
at its sole option, repair or replace the product with a like product. Replacement
product or parts may include remanufactured or refurbished parts or components.
Limited Three (3) year General Warranty
Subject to the more limited one (1) year warranty set out below, North and South
America: Three (3) years warranty for all parts excluding the lamp, three (3) years
for labor, and one (1) year for the original lamp from the date of the first consumer
purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic
office for the warranty information.
Limited One (1) year Heavy Usage Warranty:
Under heavy usage settings, where a projector’s use includes more than fourteen
(14) hours average daily usage, North and South America: One (1) year warranty
for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for the
original lamp from the date of the first consumer purchase; Europe: One (1) year
warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days
for the original lamp from the date of the first consumer purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic
office for the warranty information.
Lamp warranty subject to terms and conditions, verification and approval. Applies to
manufacturer’s installed lamp only. All accessory lamps purchased separately are
warranted for 90 days.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1.Any product on which the serial number has been defaced, modified or removed.
2.Damage, deterioration, failure, or malfunction resulting from:
a.Accident, abuse, misuse, neglect, fire, water, lightning, or other acts of nature,
improper maintenance, unauthorized product modification, or failure to follow
instructions supplied with the product.
b.Operation outside of product specifications.
c.Operation of the product for other than the normal intended use or not under
normal conditions.
d.Repair or attempted repair by anyone not authorized by ViewSonic.
e.Any damage of the product due to shipment.
f. Removal or installation of the product.
g.Causes external to the product, such as electric power fluctuations or failure.
h.Use of supplies or parts not meeting ViewSonic’s specifications.
i. Normal wear and tear.
j. Any other cause which does not relate to a product defect.
3.Removal, installation, and set-up service charges.
57
How to get service:
1. For information about receiving service under warranty, contact ViewSonic
Customer Support (please refer to “Customer Support” page). You will need to
provide your product’s serial number.
2. To obtain warranted service, you will be required to provide (a) the original dated
sales slip, (b) your name, (c) your address, (d) a description of the problem, and
(e) the serial number of the product.
3. Take or ship the product freight prepaid in the original container to an authorized
ViewSonic service center or ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center,
contact ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description
contained herein including the implied warranty of merchantability and fitness for a
particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product.
ViewSonic shall not be liable for:
1. Damage to other property caused by any defects in the product, damages based
upon inconvenience, loss of use of the product, loss of time, loss of profits, loss of
business opportunity, loss of goodwill, interference with business relationships, or
other commercial loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
Effect of local law:
This warranty gives you specific legal rights, and you may also have other rights
which vary from local authority. Some local governances do not allow limitations on
implied warranties and/or do not allow the exclusion of incidental or consequential
damages, so the above limitations and exclusions may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty information and service on ViewSonic products sold outside of the
U.S.A. and Canada, contact ViewSonic or your local ViewSonic dealer.
The warranty period for this product in mainland China (Hong Kong, Macao and
Taiwan Excluded) is subject to the terms and conditions of the Maintenance
Guarantee Card.
For users in Europe and Russia, full details of warranty provided can be found in
www.viewsoniceurope.com under Support/Warranty Information.
Projector Warranty Term Template In UG
VSC_TEMP_2005
58
Mexico Limited Warranty
ViewSonic® Projector
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal
use, during the warranty period. If a product proves to be defective in material or workmanship during
the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or components &
accessories.
How long the warranty is effective:
3 years for all parts excluding the lamp, 3 years for labor, 1 year for the original lamp from the date of
the first consumer purchase.
Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer’s
installed lamp only.
All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
a.Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product
modification, unauthorized attempted repair, or failure to follow instructions supplied with the
product.
b.Any damage of the product due to shipment.
c.Causes external to the product, such as electrical power fluctuations or failure.
d.Use of supplies or parts not meeting ViewSonic’s specifications.
e.Normal wear and tear.
f.Any other cause which does not relate to a product defect.
3.Any product exhibiting a condition commonly known as “image burn-in” which results when a static
image is displayed on the product for an extended period of time.
4.Removal, installation, insurance, and set-up service charges.
How to get service:
For information about receiving service under warranty, contact ViewSonic Customer Support (Please
refer to the attached Customer Support page). You will need to provide your product’s serial number,
so please record the product information in the space provided below on your purchase for your future
use. Please retain your receipt of proof of purchase to support your warranty claim.
For Your Records
Product Name: ________________________ Model Number: ____________________________
Document Number: ____________________ Serial Number: ____________________________
Purchase Date: ________________________ Extended Warranty Purchase? _____________(Y/N)
If so, what date does warranty expire? __________
1.To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your
name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.
2.Take or ship the product in the original container packaging to an authorized ViewSonic service
center.
3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein
including the implied warranty of merchantability and fitness for a particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not
be liable for:
1.Damage to other property caused by any defects in the product, damages based upon
inconvenience, loss of use of the product, loss of time, loss of profits, loss of business opportunity,
loss of goodwill, interference with business relationships, or other commercial loss, even if advised
of the possibility of such damages.
2.Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.
59
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within
Mexico:
Name, address, of manufacturer and importers:
México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:
Distribuciones y Servicios Computacionales SA
de CV.
Calle Juarez 284 local 2
Col. Bugambilias C.P: 83140
Tel: 01-66-22-14-9005
E-Mail: disc2@hmo.megared.net.mx
Villahermosa:
Compumantenimietnos Garantizados, S.A. de
C.V.
AV. GREGORIO MENDEZ #1504
COL, FLORIDA C.P. 86040
Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09
E-Mail: compumantenimientos@prodigy.net.mx
Puebla, Pue. (Matriz):
RENTA Y DATOS, S.A. DE C.V. Domicilio:
29 SUR 721 COL. LA PAZ
72160 PUEBLA, PUE.
Tel: 01(52).222.891.55.77 CON 10 LINEAS
E-Mail: datos@puebla.megared.net.mx
Veracruz, Ver.:
CONEXION Y DESARROLLO, S.A DE C.V. Av.
Americas # 419
ENTRE PINZÓN Y ALVARADO
Fracc. Reforma C.P. 91919
Tel: 01-22-91-00-31-67
E-Mail: gacosta@qplus.com.mx
Chihuahua
Soluciones Globales en Computación
C. Magisterio # 3321 Col. Magisterial
Chihuahua, Chih.
Tel: 4136954
E-Mail: Cefeo@soluglobales.com
Cuernavaca
Compusupport de Cuernavaca SA de CV
Francisco Leyva # 178 Col. Miguel Hidalgo
C.P. 62040, Cuernavaca Morelos
Tel: 01 777 3180579 / 01 777 3124014
E-Mail: aquevedo@compusupportcva.com
Distrito Federal:
QPLUS, S.A. de C.V.
Av. Coyoacán 931
Col. Del Valle 03100, México, D.F.
Tel: 01(52)55-50-00-27-35
E-Mail : gacosta@qplus.com.mx
Guadalajara, Jal.:
SERVICRECE, S.A. de C.V.
Av. Niños Héroes # 2281
Col. Arcos Sur, Sector Juárez
44170, Guadalajara, Jalisco
Tel: 01(52)33-36-15-15-43
E-Mail: mmiranda@servicrece.com
Guerrero Acapulco
GS Computación (Grupo Sesicomp)
Progreso #6-A, Colo Centro
39300 Acapulco, Guerrero
Tel: 744-48-32627
Monterrey:
Global Product Services
Mar Caribe # 1987, Esquina con Golfo Pérsico
Fracc. Bernardo Reyes, CP 64280
Monterrey N.L. México
Tel: 8129-5103
E-Mail: aydeem@gps1.com.mx
MERIDA:
ELECTROSER
Av Reforma No. 403Gx39 y 41
Mérida, Yucatán, México CP97000
Tel: (52) 999-925-1916
E-Mail: rrrb@sureste.com
Oaxaca, Oax.:
CENTRO DE DISTRIBUCION Y
SERVICIO, S.A. de C.V.
Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: 01(52)95-15-15-22-22
Fax: 01(52)95-15-13-67-00
E-Mail. gpotai2001@hotmail.com
Tijuana:
STD
Av Ferrocarril Sonora #3780 L-C
Col 20 de Noviembre
Tijuana, Mexico
FOR USA SUPPORT:
ViewSonic Corporation
381 Brea Canyon Road, Walnut, CA. 91789 USA
Tel: 800-688-6688 (English);
866-323-8056 (Spanish);
Fax: 1-800-685-7276
E-Mail: http://www.viewsonic.com
Projector Mexico Warranty Term Template In UG
VSC_TEMP_2006
60