Canon 7822A001 - i 950 Color Inkjet Printer Instruction manual

GENERAL INSTRUCTIONS AND FAQ’S
FAQ’S
GENERAL INSTRUCTIONS
IMPORTANT: Please read these general instructions BEFORE REFILLING
1) To avoid any potential spill or mess, refill your cartridge over a workbench or in an area that
can tolerate a spill
2) Read the instructions for your specific cartridge first before attempting to refill
3) If you have any questions, ask our technical support for assistance first before making any attempt on your own (support@uni-kit.com)
4) It is ALWAYS best to refill a cartridge when it is fresh – avoid as much as possible leaving cartridges sit empty for a long time as the print heads could clog. We include printer and head cleaner
with some kits which can help to dissolve print head clogs. You can use this cleaner in the way
explained in the instructions for your specific cartridge, and you could also pour a small amount
of the cleaner into a cup and allow the print heads of the cartridge to sit in the cleaner for a few
hours or overnight. DO NOT immerse any other parts of the cartridge in the cleaning solution,
ONLY the print heads. Keep in mind that many cartridges (like Epson, Canon) do NOT have print
heads – so this procedure does not apply. In general, you should try refilling cartridges when they
are running low or when they have freshly emptied.
5) Try avoiding over-filling any cartridge. It is always better to under-fill rather than over-fill, as
you can always fill again later. Refill slowly to avoid overfilling and creating any potential spill.
6) Be very careful to insert the correct color ink into the correct chamber. If you are unsure, you
can usually check by inserting a toothpick into the filling chamber to see what color ink was there
before. Refer to the diagrams in the instructions, or email technical support for assistance if you
need to. REMEMBER:
(1) Does using Uni-Kit ink or toner refills damage my printer?
As regards your printer warranty, please read the Magnuson-Moss Warranty Improvement Act
United States Code Annotated Title 15 Commerce and Trade Chapter 50 Comsumer Product Warranties 15
Section 2302:
No warrantor of a consumer product may condition his written or implied warranty of such product on the
consumer’s using, in connection with such product, any article or service (other than article or service provided
without charge under the terms of the warranty) which is identified by brand, trade or corporate name; except
that the prohibition of this subsection may be waived by the commission if: 1. The warrantor satisfies the Commission that the warranted product will function properly only if the article or service so identified is used in
connection with the warranted product, and 2. the Commission finds that such a waiver is in the public interest.
(4) Is the refill process messy? Is it safe?
The Uni-Kit refill kits are not messy if used carefully. The inkjet kit uses an injector system that allows you to
accurately control the filling.
The ink is not harmful unless ingested, so keep it out of reach of younger children and avoid contact with eyes.
Wash affected areas with water, and if ingested or ill effects develop, call medical aid.






BK = K = Black
C = Cyan (which is blue)
M = Magenta (which is red)
Y = Yellow (which is yellow)
PC = Photo Cyan (or light Cyan)
PM = Photo Magenta (or light Magenta)
7) If you have quality problems such as faded prints or skipping lines, try soaking the cartridge
heads a little in the print head cleaning solution or dabbing the print heads on a soft paper towel
that has been moistened with water or print head cleaning solution. You need to get the ink to
FLOW through the heads, so by dabbing on the paper towel you are creating a wicking effect that
drains the ink to the bottom and out of the heads. For other troubleshooting advice, please email
your specific problem to support@uni-kit.com. Over 90% of problems related to quality can be
solved!
What this means to you: The manufacturer of the printer you are using cannot void the warranty on your
printer because you use a cartridge or refill kit manufactured by someone other than the printer manufacturer.
(2) Will using Uni-Kit ink refills clog my printer heads?
For inkjet cartridges: Print heads may become clogged if the cartridge is left empty for an excessive period of
time. It is always best to refill before the cartridge empties or soon after it empties. Clogged print heads can
be unclogged most of the time by soaking the cartridge print heads in our “cartridge and print head cleaner”
solution for a few hours. As long as you refill your cartridge soon after it empties (preferably even before it is
completely empty), you will minimize the risk of clogged print heads.
(3) How many refills will I get from 1 kit?
This depends on the cartridges you have. With the Combo Uni-Kit Inkjet Refill Kit you can refill most black and
color inkjet cartridges about 3-7 times each.
(5) Will the Uni-Kit work with my specific printer?
Yes, if you have an inkjet printer it can be refilled with the Uni-Kit Inkjet Refill System. This is because all
inkjet cartridges have a filling hole which can be exposed and used to refill that cartridge with more ink. The
Uni-Kit has a specially designed ink that works in ALL inkjet printers. Our instructions are updated regularly; if your printer or cartridge is not listed in the instruction manual please email tech support: support@
uni-kit.com. Some printers or cartridges have “lockout” mechanisms that prevent the cartridge from being
recognized after it is refilled. Note: Some printers will STILL PRINT even though they give an error message,
you can ignore the error message and continue printing. For Epson cartridges, these require that their chips
be reset; an Epson Resetter is sold separately.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
I
Brother Cartridges
IN-700, LC11BK ______________________________1
IN-710C, LC11CL _____________________________1
LC03BC, LC03MY ____________________________2
LC01BK, LC01C, LC01M, LC01Y _________________3
LC02BK, LC02C, LC02M, LC02Y, LC21Bk, LC21C,
LC21M,LC21Y, LC31C, LC31M, LC31Y, LC31BK____4
LC04C, LC04M, LC04Y, LC04BK_________________5
LC41C, LC41M, LC41Y, LC41BK_________________6
LC25Bk, LC25C, LC25M, LC25Y_________________6
LC51_______________________________________7
LC61BK, LC61C, LC61Y, LC61M, LC65BK, LC65C,
LC65Y, LC65M, LC71BK, LC71C, LC71Y, LC71M,
LC75BK, LC75C, LC75Y, LC75M, LC79BK, LC79C,
LC79Y, LC79M, LC103BK, LC103C, LC103M, lC103Y,
LC105BK, LC105C, LC105M, LC105Y_____________8
BC-22e______________________________________17
PG-30,PG-40, PG-50, CL-41, CL-51, CL-52, PG-210,
CL-211, PG-240, CL-241, PG-245, CL-246, PG-440,
CL-441 _____________________________________18
Compaq Cartridges
337714-001, 180845-001, 337709-001, 180847-001, 337715001, 180846-001, 337710-001, 180848-001,180844-001,
337711-__________________________________________________19
Dell Cartridges
7Y743, T0529, T0601__________________________20
7Y745, T0530, T0602__________________________20
MK990, MK991, MK992, MK993, Series 5, Series 7,
Series 8, Series 9, Series 11, Series 15______________46
Dell 21, 22, 23, 24 Series__________________________21
Canon Cartridges
Digital Cartridges
BCI-21 & 24__________________________________9
BC-20 & BC-23 _______________________________10
BJI-201BK HC, BJI-201BK, BJI-201C, BJI-201M,
BJI-201Y____________________________________11
BC-01, BC-02, BC-05, BX-02, BX-03, BC-06________12
BCI-60, BCI-61, BCI-62________________________13
BCI-3eBk, BCI-3eC, BCI-3eM, BCI-3eY, BCI-3Bk,
BCI-3C, BCI-3M, BCI-3Y, BCI-3PBk, BCI-3PC,
BCI-3PM, BCI-5Bk,BCI-5C, BCI-5M, BCI-5Y, BCI-5PC,
BCI-5PM, BCI-6Bk, BCI-6C, BCI-6Y, BCI-6M, BCI-8Bk,
BCI-8C, BCI-8M, BCI-8Y, BCI-8PBk, BCI-8PC, BCI-8PM,
CLI-8, PGI-5,PGI-220, CLI-221,PGI-225, CLI-226, PGI250, CLI-251_________________________________14
BCI-15B, BCI-16C_____________________________16
LJ50X-AB, LJ50X-AK, LJ50X-AC_________________22
Epson Cartridges
S020062, S020118, S020122, S020130______________23
S020093, S020097, S020110, S020193, S020187,
S020189, S020191, S020089, S020093, S020108,
S020047, S020049, S020097, S020034, S020036,
S020138, T007201, T008, T008201, T009, T009201, T013,
T014, T015201, T016201, T017, T018, T019201, T020201,
T026, T027, T028, T029, T036120, T037020, T040120, T04
1020_______________________________________24
T0321,T0322, T0323, T0324, T0331, T0332, T0333,
T0334, T0335, T0336, T0341, T0342, T0343, T0344,
T0345, T0346, T0347, T0348, T0422, T0423, T0424,
ICD Y21____________________________________25
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
II
INDEX
Epson Cartridges
T0431, T0441, T0442, T0443, T0444, T0481, T0482,
T0483, T0484, T0485, T0486, T0540, T0541, T0542,
T0543, T0544, T0545, T0546, T0547, T0548, T0549,
T0601-T0604_________________________________26
T124, T125, T126, T127, T128 Series ______________27
Hewlett Packard Cartridges
51626A, 51629A, 51626G, 51629G, 51633M, C6614AN,
C6628AN____________________________________28
51625A, 51649A , 51649G, C1816A _______________29
51645A, 51645G, 51640A, 51640C, 51640M, 51640Y,
51644C, 51644M, 51644Y, C6615DN , C6615AN_____30
51641A, C1823A, C1823D, C1823G, C6625AN,
C6578AN, C6578DN, C3844A , C3845A___________31
C4841A, C4842A, C4843A, C4844A, 38, 50, 70, 72, 80
81, 82, 83, 84, 85, 88, 90, 940______________________32
21, 22, 27, 28, 56, 57, 58, 60, 61 & 61XL, 74,
74XL, 75, 75XL, 92, 93, 94, 95, 97, 98, 99, 110,
901___________________________33
701_________________________________________34
564, 920 Cartridges____________________________35
C1806A, C1807A, C1808A, C1809A_______________36
C5010A, C5011A_____________________________37
C6634A, C6635A_____________________________38
C8721,C8771,C8772,C8773,C8774,C8775 (HP 02)
Cartridges___________________________________38
932, 933, 950, 951_____________________________40
Kodak Cartridges
#10, #30 Black Cartridge_________________________________42
#10, #30 Color Cartridge_________________________________42
Lexmark Cartridges
18L0032, 18L0042______________________________20
10N0016, 10N0217, 12A1970, 12A1975, 1361400,
13400HC, 1380620, 1382050, 15M2971, 16G0055,
17G0050, 18L0032,_____________________________43
12A1980, 12A1985, 1380619, 10N0026,, 10N0027, 15M0120,
15M0125, 18L0042, 1382060, 17G0060, 16G0065______43
12A1990, 1361760______________________________43
1380490, 1380491, 1380492, 1380493________________44
18C0031, 18C0032, 18C0033, 18C0034, 18C0035______45
#1, #2, #3, #4A, # 5A, #14A, #15A, #23A, #24A, #28A,
#29A, #32, #33, #34, #35, #36A, #37A, #41A, #42A, #43,
#44, _________________________________________46
100A, 108A, 150A, 200A_________________________47
Okidata Cartridges
52109301__________________________________48
52109302__________________________________48
52110001, 52110002, 52110003, 52110004_________49
Pitney Bowes Cartridge
769-0____________________________________________50
793-5____________________________________________58
797-0____________________________________________59
765-0____________________________________________60
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
III
INDEX
Sharp Cartridges
AJ-C50B, UX-C70B_____ _____________________51
AJ-C50C___________________________________51
Xerox Cartridges
8R12591, 8R7880, 8R882 ______________________52
8R7881____________________________________52
8R7660, 8R7661, 8R7662, 8R7663________________53
8R7638____________________________________54
8R7903,8R7904______________________________55
8R12728____________________________________56
8R7971, 8R7972, 8R7973, 8R7974________________57
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
IV
CLICK HERE TO GO THE INDEX
Brother Cartridges
Black Cartridges:
IN-700, LC11BK
1. Use the enclosed eyelet screw to enlarge the filling hole located at the top of the cartridge. (Do not remove the cap.)
2. Connect the needle to the syringe and fill the syringe with 8 ml. of Cartridge & Print
Head Cleaner and inject into the cartridge. Reinsert cartridge into printer and print 5
test pages.
3. Fill the syringe with ink. Insert the needle into the filling hole and push down into the
cartridge. Inject up to 20 ml.. of ink or until the cartridge is full.
Note: Immediately refill any empty cartridges.
Filling Hole
Color Cartridges:
IN-710C, LC11CL
1. The filling holes are located under the plastic cap. Use a thin flathead screwdriver or
knife to remove the cap. Important: Do not to damage the sensors on the back of the
cartridge.
Sensors
Magenta
2. Connect the needle to the syringe and fill with ink.
3. Insert the needle into the matching hole of the color to be refilled, (see diagram above)
and push into the cartridge. Note: You will feel a slight pressure because the cartridge contains a sponge.
Yellow
4. Inject about 8 ml. of ink, per color, into the cartridge until the ink begins to bubble at
the top of the sponge. Important: Do not overfill. Keep the sponge inside the cartridge white.
5. Rinse the needle and syringe with water and dry between each color refilling or store
for future use.
Cyan
6. The cover can be reattached with a piece of tape.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
1
CLICK HERE TO GO THE INDEX
Brother Cartridges
Waste
Ink Port
Black
Filling Hole
LC03BC, LC03MY
1. The filling hole is the same hole as the hole that connects to the printer.
Cyan
Filling Hole
2. Note: The cartridge is lined in a delicate Mylar bag and it is very important not to
insert the needle more than 3/4” or it is possible to pierce or tear the Mylar bag. Important: It is very important to turn the cartridge as shown in the pictures. If you
have the cartridge reversed then you will put the wrong color of ink in the wrong fill
hole. Fill the syringe with ink and carefully insert the needle into the filling hole and
slowly inject about 4 ml. of ink into the cartridge.
3. Hold the cartridge up with the filling hole at the top. Using the syringe, remove any
trapped air in the cartridge by only inserting the tip of the needle and pulling up on
the plunger until all air is removed.
4. Remove the syringe and rinse with water and dry for future use, or to use with a different color ink.
5. Reinsert the cartridge and run a priming cycle as per printer instructions.
NOTE: It is not necessary to disassemble the cartridge to refill it and we strongly recommend you do not.
Magenta
Filling Hole
Yellow
Filling Hole
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
2
CLICK HERE TO GO THE INDEX
Brother Cartridges
LC01BK, LC01C, LC01M, LC01Y
Filling Hole
1. The filling hole is located under the label as shown. Just peel back the label leaving it
still connected to the cartridge, do not remove completely.
2. Use the provided eyelet screw to drill a filling hole on the top of the cartridge(s) into
the lower area.
3. Connect the needle to the syringe and fill with ink..
4. Insert the needle into the filling hole and inject about 10ml of ink.
5. Pull the label back into place and use a piece of tape to hold it in place.
6. Rinse the syringe with water and dry between each color refill or store for future use.
7. Reinsert cartridge back into the printer and run 1 - 3 cleaning cycles as per printer
instructions.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
3
CLICK HERE TO GO THE INDEX
Brother Cartridges
LC02BK, LC02C, LC02M, LC02Y, LC21Bk, LC21C, LC21M, LC21Y,
LC31C, LC31M, LC31Y, LC31BK
1. Put a piece of tape over the bottom hole of the cartridge.
Tape
2. Use a flathead screwdriver to remove the cover by prying up the clip holding the cover
on the cartridge.
3. Using a knife remove both the small and large silver seals.
4. Underneath the large silver seal there are two holes (filling hole and vent hole), use the
eyelet screw to widen the hole closest to the center of the cartridge (not the hole closest
to the edge of the cartridge) Also widen the small hole located under the small silver
seal.
5. Connect the needle to the syringe and fill ink.
6. Insert the syringe into the hole that was located under the large silver seal. Note: You
may feel a slight pressure because the cartridge contains a sponge.
7. Inject about 7 ml. of ink and reseal the filling hole and vent hole with a piece of tape.
8. Insert the syringe into the small filling hole no more than 1/4” and inject approximately 3 ml. of ink and seal with a piece of tape.
9. Snap the plastic cover back onto the cartridge the same direction it came off.
10. Rinse the syringe with water and dry between each color refill or store for future use.
Filling Hole
11. Remove the tape covering the bottom hole and reinsert the cartridge(s) and run a
priming cycle as per printer instructions.
Vent Hole
Note: Immediately refill any empty cartridge
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
4
CLICK HERE TO GO THE INDEX
Brother Cartridges
LC04C, LC04M, LC04Y, LC04BK
1. Put a piece of tape over the bottom hole of the cartridge.
2. Use a flathead screwdriver to remove the cover by prying up the clip holding the cover
on the cartridge.
3. Using a knife remove the large silver seal.
4. Underneath the large silver seal there are two holes (filling hole and vent hole), use the
eyelet screw to widen the hole closest to the center of the cartridge (not the hole closest
to the edge of the cartridge).
5. Connect the needle to the syringe and fill ink.
6. Insert the syringe into the hole that was located under the large silver seal. Note: You
may feel a slight pressure because the cartridge contains a sponge.
Filling Hole
7. Inject about 7 ml. of ink and seal the filling hole and vent hole with a piece of tape.
8. Snap the plastic cover back onto the cartridge the same direction it came off.
9. Rinse the syringe with water and dry between each color refill or store for future use.
10. Remove the tape covering the bottom hole and reinsert the cartridge(s) and run a
priming cycle as per printer instructions.
Note: Immediately refill any empty cartridge
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
5
CLICK HERE TO GO THE INDEX
Brother Cartridges
LC41C, LC41M, LC41Y, LC41BK
1. Stand the cartridge on a towel or ink spillable table. Using the eyelet screw provided,
begin twisting the screw into the front of the cartridge (see illustration to the right).
Continue twisting until it pierces the plastic..
Creat Refill Hole
2. Connect the needle to the syringe and fill with ink.
3. Insert the syringe into the hole and inject about 20 ml. of ink
4. Seal the filling hole with one of the included tape dots or a piece of duct tape.
5. Rinse the syringe with water and dry between each color refill or store for future use.
LC25Bk, LC25C, LC25M, LC25Y
1. Use the eyelet screw to remove the white plug located next to the exit hole. The plug
does not need to be removed completely since the white plug and the exit hole plug are
connected.
2. Connect the needle to the syringe and fill with ink.
3. Insert the syringe through the filling hole which is found where the white plug was
removed.
4. Inject up to 8 ml. of ink (this cartridge is transparent so you will see the ink level) then
reseal the cartridge with the plug that was removed from step 1. Make sure that the
small plastic tip of the plug sits back into the filling hole.
Outlet Hole
Filling Hole
5. Rinse the syringe with water and dry for future use, or use with a different color ink.
6. Reinsert the cartridge(s) and run a priming cycle as per printer instructions.
Note: Immediately refill any empty cartridge
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
6
CLICK HERE TO GO THE INDEX
Brother Cartridges
LC51
1. Cut the label at joint between the top and bottom halves of the cartridge case.
2. Flip open the cartridge casing (shell).
1.
3. Remove the cartridge from the casing (shell).
2.
4. There is a round hole (well) in the top of the cartridge. Inside the hole or well is
a rubber stopper. Use a thumb drill and drill through the rubber stopper.
Note: Do not bump or press the “pressure release button”.
5. Attach the needle onto the syringe and fill the syringe with 10 ml of ink.
6. Insert the needle through the drilled stopper hole and into the cartridge body.
Please be sure the needle does not press up against the bag or puncture it, as this
will ruin the cartridge and make it unusable.
7. Very slowly inject the 10 ml of ink into the cartridge bag. If ink starts to come
out of the filling hole, stop, as the cartridge is now full (pull back 1 ml of ink
from the cartridge back into the syringe to insure that the cartridge is not overfilled). Unused ink can be returned to the bottle.
3.
8. Remove the syringe with needle from the cartridge and seal the hole using the
green tape dots provided or electrical tape. Make sure the hole is sealed airtight.
9. Place the cartridge back into its casing (shell) and use a piece of tape to hold the
two sides of the casing (shell) together.
10. Re-install the cartridge back into the printer and run 1 to 3 cleaning cycles as
per printer instructions.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
7
CLICK HERE TO GO THE INDEX
Brother Cartridges
LC61C, LC61M, LC61Y, LC61BK,
LC65BK, LC65C, LC65Y, LC65M
LC71C, LC71M, LC71Y, LC71BK
LC75C, LC75M, LC75Y, LC75BK,
LC79BK, LC79C, LC79Y, LC79M
LC103BK, LC103C, LC103M, lC103Y,
LC105BK, LC105C, LC105M, LC105Y
Air Nozzle
1. Place the cartridge over a towel, or paper towel.
2. Remove the bottom portion of the cartridge by pushing in the small tabs that
hold it in place. In order to do this, you will need a small flat head screwdriver.
3. Once the bottom portion is removed, find the Ink nozzle. Fill the syringe with
about 10ml of ink. Place the syringe into the ink nozzle just as shown in the
image to the left.
4. Find the Air Nozzle. Before attempting to push the ink into the cartridge you
must keep in mind that air must be released via the air nozzle. In order to do
this, push the tab sticking out of the air nozzle in while you fill the cartridge.
Ink Nozzle
5. Refill slowly. Ink can spill out of the air nozzle if its pushed in to quickly. Fill
slow, and watch the ink as it fills through the see through plastic.
6. Once your done, release the air nozzle, and remove the syringe from the ink
nozzle.
7. Place the bottom cover back on, and your cartridge is now ready for use.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
8
CLICK HERE TO GO THE INDEX
Canon Cartridges
BCI-21 Black & 24 Black
BCI-21 Color & 24 Color
1. Use a knife to remove the top of cartridge(s).
2. Use the included eyelet screw to enlarge the filling hole(s) in the top of the cartridge(s).
3. Connect the needle to the syringe and fill with ink.
4. Insert the syringe into the correct filling hole, (See diagram below for filling hole color)
and push into the center of the cartridge. Note: You may feel a slight pressure because
the cartridge contains a sponge.
Magenta
Filling Hole
5. Inject up to 5 ml. of ink, per color, into the cartridge.
6. Reposition the top and secure with a piece of tape.
Cyan
Filling Hole
7. Rinse the syringe with water and dry between each color filling or store for future use.
8. Reinsert the cartridge(s) and run a cleaning cycle as per printer instructions.
Yellow
Filling Hole
Black
Filling Hole
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
9
CLICK HERE TO GO THE INDEX
Canon Cartridges
BC-20 & BC-23
High Capacity Cartridge
1. Use the eyelet screw to remove plug located on top of the cartridge.
Filling Hole
2. Connect the needle to the syringe and fill with ink.
3. Insert the syringe through the filling hole and push into the cartridge. Note: You may
feel a slight pressure because the cartridge contains a sponge.
4. Inject up to 30 ml. of ink then reseal the cartridge with the plug that was removed
from step 1.
5. Rinse the syringe with water and dry for future use, or use with a different color ink.
6. Reinsert the cartridge(s) and run a priming cycle as per printer instructions.
Note: Immediately refill any empty cartridges.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
10
CLICK HERE TO GO THE INDEX
Canon Cartridges
Filling Hole
BJI-201BK HC, BJI-201BK, BJI-201C, BJI-201M, BJI-201Y
1. With the cartridge upside down, using a screwdriver, push in the ball bearing that seals
the filling hole. NOTE: There are several versions of these cartridges. One version
has the filling hole under the label on the top of the cartridge. Another version does
not have a ball bearing at all. In this case it would be necessary to make a hole for
the needle to be inserted. Make this hole in the same spot where the ball bearing
would be located, as shown below. Seal hole with the plug provided.
2. Connect the needle to the syringe and fill with ink.
3. Inject about 5 ml. of ink into the filling hole until the tank is full.
4. Use the included plug to seal the filling hole, make sure that the plug is sitting flush in
the cartridge. Additional Note: If the cartridge has been empty/dry, the sponge will
no longer accept any ink which will cause the cartridge to leak.
Outlet Hole
5. Rinse the syringe with water and dry for future use, or use with a different color ink.
6. Reinsert the cartridge and run a priming cycle as per printer instructions.
Note: Immediately refill any empty cartridges.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
11
CLICK HERE TO GO THE INDEX
Canon Cartridges
Black
Filling Hole
BC-01, BC-02, BC-05, BX-02, BX-03,
1. Use the eyelet screw to remove plug located on the top side of the cartridge.
FOR BX-03 ONLY: A hole must be made on the top of the cartridge by using the hole making tool included in the kit. . Firmly hold the handle of the
tool and begin twisting the tool into the top corner of the cartridge. Continue
twisting until it pierces the plastic cover. Once the plastic to is pierced, making
the rest of the hole will go very quickly.
2. Connect the needle to the syringe and fill with ink.
3. Insert the syringe through the filling hole and push into the cartridge. Note:
You may feel a slight pressure because the cartridge contains a sponge.
4. Inject up to 30 ml. of ink then reseal the cartridge with the plug that was
removed from step 1. FOR BX-03 ONLY: Use the plug provided in the kit to
seal the cartridge.
Printer Head
Cyan
Filling Hole
5. Rinse the syringe with water and dry for future use, or use with a different
color ink.
Magenta
Filling Hole
6. Reinsert the cartridge(s) and run a priming cycle as per printer instructions.
Note: Immediately refill any empty cartridges.
Yellow
Filling Hole
Printer Head
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
12
CLICK HERE TO GO THE INDEX
Canon Cartridges
Black
Filling Hole
BCI-60, BCI-61, BCI-62
1. The filling holes are located under the label as shown. Just peel back the label
leaving it still connected to the cartridge, do not remove completely.
2. Use the provided eyelet screw to widen the filling hole(s) in the top of the
cartridge(s).
3. Connect the needle to the syringe and fill with ink.
4. Insert the needle into the widen filling hole. Note: This cartridge has a
sponge so you may feel a slight pressure. Inject about 10 ml. of ink, per
color until the ink bubbles up.
Cyan
Filling Hole
Yellow
Filling Hole
5. Pull the label back into place and use a piece of tape to hold it in place.
6. Rinse the syringe with water and dry between each color refill or store for
future use.
7. Reinsert cartridge back into the printer and run 1 - 3 cleaning cycles as per
printer instructions.
Magenta
Filling Hole
Note: Immediately refill any empty cartridge
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
13
CLICK HERE TO GO THE INDEX
Canon Cartridges
BCI-3e , BCI-3, BCI-5, BCI-6, Cli-8, PGI-5, PGI-220,
CLI-221, PGI-225, CLI-226, PGI-250, CLI-251
(All Colors)
NOTE: Canon Resetter may be required to have the
cartridges resgister as full upon installation.
Method #1
1. Using a manual drill or the small
drill provided with your refill kit,
drill through the plastic casing on the side of the cartridge.
Drill enough to break through
the plastic. Do not drill into the
sponge area beyond the inner
plastic casing.
2. Once the hole has been created, use the syringe to penetrate
through the sponge, and guide the needle into the ink chamber
as shown in the illustration to the left. Slowly inject the ink into
the chamber until 1/2 of it has been filled. Do not fill to the
chamber more than the recommended amount. Doing so
will cause more ink to flow into the sponge area, forcing ink to
exit through the nozzle port (Area where the ink flows out of
the cartridge).
3. Once the cartridge has been filled, careful pull the needle out of the cartridge. It is recommended
that you use hot glue to seal the hole created, however, you can use silicon to cover the hole, and
help complete the seal with some type of instant glue. Be sure to allow the cartridge seal to dry
before inserting it into the printer. Placing the cartridge into the printer to early may break the
seal and cause the cartridge to leak.
Note: Make sure to seal the hole completely and not leave any cracks that would cause leaking.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
14
CLICK HERE TO GO THE INDEX
Canon Cartridges
Refill Hole
(Ball Bearing)
Air Vent
Method #2
1. Use electrical or duct tape to seal the Air Vent found on the top of the cartridge.
Note: Make sure tape is completely covering the vent.
2. Remove the label partially, only to expose the ball bearing underneath. Then use a screwdriver or an L. tool to push the ball bearing into the cartridge. This will give access to the
filling hole.
3. Connect the needle to the syringe and fill with ink.
4. Use your finger as a plug by covering the outlet port. Keep your finger on the outlet port
until you have finished refilling and the refill hole is plugged. If you let go any time earlier,
ink may and can spill out of that outlet.
5. Inject about 10 ml. of ink into the filling hole or until the ink chamber is full. Be sure to
leave enough room in the ink chamber for the silicon plug, it will create pressure when
inserted.
Sponge Chamber
6. Put a silicone plug in the refill hole to seal it, make sure it is air tight. If extra silicone from
the plug is sticking out, you may trim it down to a practical size. Be sure to leave enough
to make it easy for you to remove the next time you wish to refill the cartridge.
Outlet Port
Ink Chamber
Push in the ball bearing (may require
some force)
7. Remove your finger from the outlet (small drops may leak out, but once the cartridge pressure stabilizes itself, it will stop) and remove the tape from earlier off the vent.
8. Rinse the syringe with water and dry for future use, or use with a different color ink.
9. Reinsert the cartridge and run a priming cycle as per printer instructions.
Note: If the cartridge continuously leaks, place the cartridge on its side until the dripping
stops. Also, check the seal on the cartridge to make sure it is airtight.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
15
CLICK HERE TO GO THE INDEX
Canon Cartridges
BCI-15B / BCI-16C
1. Put the cartridges on some paper towels in an area where you can tolerate a spill.
2. Turn the cartridge up side down so that the outlet port of the cartridge is
facing upward.
3. Fill the syringe with 3ml of ink for the color being refilled.
4. Drip ink onto the felt pad in the outlet port. The felt pad will quickly
absorb the ink into the cartridge. If the felt pad will not soak up any
more ink and the ink just sits on top then that chamber is full. Dab a paper towel onto the felt pad to soak up any ink that did not get absorbed
into the cartridge.
5. Please be sure that you put the correct color into the correct chamber
otherwise you will color contaminate. Contaminating another color is
not reversable, and may require you to start over with a new cartridge.
Note: Do not pierce the felt pad with the needle of the syringe.
6. Replace the cartridge and run 1 - 3 cleaning cycles as per printer instructions.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
16
CLICK HERE TO GO THE INDEX
Canon Cartridges
Yellow
BC-22e
Magenta
1. Use the eyelet screw to remove the plugs located on top of the cartridge.
Cyan
Black
2. Connect the needle to the syringe and fill with ink.
3. Insert the syringe through the filling hole and push into the cartridge. Note:
You may feel a slight pressure because the cartridge contains a sponge.
4. Inject up to 10 ml. of ink, per color, then reseal the cartridge with the plug that
was removed from step 1.
5. Rinse the syringe with water and dry for future use, or use with a different
color ink.
6. Reinsert the cartridge(s) and run a priming cycle as per printer instructions.
Note: Immediately refill any empty cartridges.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
17
CLICK HERE TO GO THE INDEX
Canon Cartridges
1. Remove the label from the top of cartridge
2. Using the drill tool, widen the refill holes for each color. Please use the illustrations on the
right for color guidance.
PG-30/PG-40/PG-50
PG-210/PG-240/PG-245
PG-440
CL-31/CL-41/CL-51
CL-211/CL-241/CL-246
CL-441
3. Attach the needle to syringe and load syringe with 6 ml of ink for each color in the color cartridge or 20 ml for the black cartridge.
CL-52
MAGENTA
PHOTO CYAN
4. Insert needle into corresponding color and penetrate the sponge inside. Insert the needle only
a 1/4 of an inch in.
If the needle penetrates to the bottom of the cartridge, the cartridge will leak and is not
salvageable.
BLACK
CYAN
YELLOW
BLACK
PHOTO MAGENTA
5. SLOWLY inject the ink into the cartridge. Reverse the process and pull about 1 ml of ink if it
has spilled out the top of the cartridge.
6. Repeat steps 5, 6, 7, 8 until all colors have been injected.
7. Clean off the top of the cartridge. Place tape over the top of the cartridge so it covers every
hole.
8. Use a pin and put a small hole (vent hole) through the tape for each hole on the top of the
cartridge.
This is important, don’t skip this step. The cartridge must be vented to atmosphere or it will
not work.
9. Reinstall in printer and run one or two cleaning cycles until the cartridge begins to print correctly.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
18
CLICK HERE TO GO THE INDEX
Compaq Cartridges
Fill Hole
Black Cartridges:
337714-001, 180845-001, 337709-001, 180847-001
1. Use the enclosed eyelet screw to enlarge the filling hole located at the top of the cartridge.
(Do not remove the cap.)
2. Connect the needle to the syringe and fill the syringe with 8 ml. of Cartridge & Print Head
Cleaner and inject into the cartridge. Reinsert cartridge into printer and print 5 test pages.
3. Fill the syringe with ink. Insert the needle into the filling hole and push down into the
cartridge. Inject up to 20 ml. of ink or until the cartridge is full.
Note: Immediately refill any empty cartridges.
Color Cartridges:
337715-001, 180846-001, 337710-001, 180848-001,180844-001,
Photo cartridges:
337711-001(photo)
1. The filling holes are located under the plastic cap. Use a thin flathead screwdriver or knife
to remove the cap. Important: Do not to damage the sensors on the back of the cartridge.
Cyan
Yellow
Magenta
2. Connect the needle to the syringe and fill with ink.
3. Insert the needle into the matching hole of the color to be refilled, (see diagram above)
and push into the cartridge. Note: You will feel a slight pressure because the cartridge
contains a sponge.
4. Inject about 8 ml. of ink, per color, into the cartridge until the ink begins to bubble at the
top of the sponge. Important: Do not overfill. Keep the sponge inside the cartridge white.
5. Rinse the needle and syringe with water and dry between each color refilling or store for
future use.
6. The cover can be reattached with a piece of tape.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
19
CLICK HERE TO GO THE INDEX
Dell Cartridges
Black Cartridges:
Dell: 7Y743, T0529, T0601
Lexmark: 18L0032
Fill Hole
Slot
1. Use the enclosed eyelet screw to enlarge the filling hole located at the top of the cartridge. (Do
not remove the cap.)
2. Connect the needle to the syringe and fill the syringe with 8 ml. of Cartridge & Print Head
Cleaner and inject into the cartridge. Reinsert cartridge into printer and print 5 test pages.
3. Fill the syringe with ink. Insert the needle into the filling hole and push down into the cartridge. Inject up to 20 ml. of ink or until the cartridge is full.
Note: Immediately refill any empty cartridges
Color Cartridges:
Dell: 7Y745, T0530, T0602
Lexmark: 18L0042
Slot
Magenta
Cyan
1. The filling holes are located under the plastic cap. Use a thin flathead screwdriver or knife to
remove the cap. Important: Do not to damage the sensors on the back of the cartridge.
2. Connect the needle to the syringe and fill with ink.
3. Insert the needle into the matching hole of the color to be refilled, (see diagram above) and
push into the cartridge. Note: You will feel a slight pressure because the cartridge contains a
sponge.
Yellow
4. Inject about 8 ml. of ink, per color, into the cartridge until the ink begins to bubble at the top of
the sponge. Important: Do not overfill. Keep the sponge inside the cartridge white.
5. Rinse the needle and syringe with water and dry between each color refilling or store for future
use.
6. The cover can be reattached with a piece of tape.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
20
CLICK HERE TO GO THE INDEX
Dell Cartridges
Dell 21, 22, 23, 24 Series
1. Peel back the label from the top of the cartridge to expose the refill holes of the cartridge. (If the illustration on the right differ from your cartridge model, use 3 toothpicks and poke each hole to determine its color)
BLACK
2. Fill the syringe with 10 ml of black ink (5 ml for each color on color cartridges).
3. Insert the needle into the cartridge gently, however, make sure you don’t push the
needle in to the cartridge too deep. Doing so could cause it to go right through the
sponge and come out the other end, causing the sponge to break. To be safe, insert the
needle very slightly, and inject the ink..
4. Once the cartridge has been refilled, stick the label back in place, if the label has been
destroyed, use duct tape or electrical tape. (Try keeping the label size when using tape)
5. Rinse the syringe with water and dry between each color refill or store for future use.
6. Reinstall the cartridge and run 1 - 3 test pages as per printer instructions. If necessary
leave the cartridge in printer for up to 24 hours to allow ink to flow to the print head.
YELLOW
7. After you refill and reinsert the cartridge(s) back into the printer, the printer will still
“remember” the cartridge as empty so it will continue to give you a low/out of ink
warning. Some printers will still allow you to print, but if your printer will not, you
will need to replace the chip on the cartridge (check for availability).
CYAN
MAGENTA
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
21
CLICK HERE TO GO THE INDEX
Digital Cartridges
Yellow
LJ50X-AB, LJ50X-AK, LJ50X-AC
Color Cartridge
Cyan
1. The filling holes are located under the cap. The cap is easily removed by simply
pulling it off with your fingers. Be careful not to damage the sensors on the
back
Magenta
2. Connect the needle to the syringe and fill with ink.
3. Insert the needle into the filling hole of the color to be refilled, pushing it down
into the cartridge. Note: You may feel a slight pressure because the cartridge
contains a sponge.
4. Inject about 8 ml. of ink, per color, or until the ink bubbles at the filling hole.
Black Cartridge
1. The actual cartridge is located inside a plastic shell. To remove it pry the locking tab out and pull the cartridge out of the plastic shell. Important: All of
the parts in the cartridge are very sensitive and delicate and should not be
touched. They can be damaged easily.
Black
2. Using a screwdriver remove the plug (not shown) from the filling hole. (Do
not remove the top).
3. Fill the syringe with ink, insert the filling needle into the filling hole and push
3/4 of the way into the cartridge. Inject about 15 ml. of ink or until the ink
tank is full.
4. Slide the cartridge back into the plastic shell and reinsert into the printer.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
22
CLICK HERE TO GO THE INDEX
Epson Cartridges
S020062, S020118, S020122, S020130
1. The filling hole is the same hole as the hole that connects to the printer.
2. Note: The cartridge is lined in a delicate Mylar bag and it is very important
not to insert the needle more than 3/4” or it is possible to pierce or tear the
Mylar bag. Fill the syringe with the correct color ink and carefully insert
the needle into the filling hole and slowly inject approximately 90 ml. of ink
into the cartridge.
3. Hold the cartridge upright with the filling hole at the top. Using the syringe,
remove any trapped air in the cartridge by only inserting the tip of the needle
and pulling up on the plunger until all air is removed.
4. Remove the syringe and rinse with water and dry for future use, or to use with
a different color ink.
5. Reinsert the cartridge and run a priming cycle as per printer instructions.
Note: Immediately refill any empty cartridges.
NOTE: It is not necessary to disassemble the cartridge to refill it and we strongly
recommend you do not. We have included a picture of the inside of the cartridge
to satisfy your curiosity.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
23
CLICK HERE TO GO THE INDEX
Epson Cartridges
S020093, S020097, S020110, S020193,
S020187, S020189, S020191, S020089, S020093,
S020108, S020047, S020049, S020097, S020034, S020036, S020138,
T001, T003011, T003012, T005011,
A Chip Resetter (sold separately) is needed for the following:
T007201, T008, T008201, T009, T009201, T013, T014, T015201,
T016201, T017, T018, T019201, T020201, T026, T027, T028, T029,
T036120, T037020, T040120, T041020
Cyan
1. Put a piece of tape over each outlet hole(s) at the bottom of the cartridge.
Magenta
Yellow
2. Connect the needle to the syringe. Before filling the syringe with ink, use the
needle tip to pierce through the label to create the filling hole. Then fill the
syringe with the appropriate color ink.
3. Slowly inject approximately 8 ml. of ink, per color, until the cartridge is full.
4. Use tape to seal the hole(s) made in the top of the label.
Black
5. Rinse the syringe with water and dry between each color refill or store for
future use.
Follow this step for cartridges WITHOUT the smart chip:
6. Leave the tape on the outlet hole(s) and insert the cartridge into the printer
and run 1 - 3 cleaning cycles as per printer instructions. It may be necessary
to leave cartridge in printer for up to 24 hours to allow ink to flow to the print
head.
Cyan
Black
Magenta
Yellow
Fill Hole
Photo Cartridge
NOTE: If cartridge is refilled before it is completely empty this time is greatly
reduced.
Cyan
Light Cyan
Magenta
Light Magenta
Yellow
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
24
CLICK HERE TO GO THE INDEX
Epson Cartridges
A Chip Resetter (sold separately) is needed for the following cartridges:
T0321,T0322, T0323, T0324, T0331, T0332, T0333, T0334, T0335, T0336,
T0341, T0342, T0343, T0344, T0345, T0346, T0347, T0348, T0422, T0423,
T0424, ICD Y21
Filling Hole
1. Turn the cartridge upside down and using a paper clip or a similar object, pierce
through the label into the cartridge of the proper filling hole (as shown below).
2. Connect the needle to the syringe and fill with ink.
3. Inject about 5 - 7 ml. of ink into the filling hole until the cartridge is almost full.
Be aware that the needle will only go into the cartridge about 3/8 of an inch.
Do not use
this hole
4. Use the tape dot to seal the filling hole, make sure it is completely sealed.
5. Rinse the syringe with water and dry for further use, or use with a different color
ink.
6. Follow the resetting instructions before inserting cartridge into printer.
Note: Immediately refill any empty cartridges.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
25
CLICK HERE TO GO THE INDEX
Epson Cartridges
A Chip Resetter (sold separately) is needed for the following cartridges:
T0431, T0441, T0442, T0443, T0444, T0481, T0482, T0483, T0484,
T0485, T0486, T0540, T0541, T0542, T0543, T0544, T0545, T0546,
T0547, T0548, T0549, T0601-T0604
Create Refill hole
1. It is important to understand the sections of this cartridge before refilling. Please
study diagram closely.
2. Using the eyelet screw, create a hole (see illustration to the right). Keep the screw
centered when drilling the hole.
3. Connect the needle to the syringe and fill with the correct color ink.
4. Insert the needle into the newly created hole. Inject about 12 ml. of ink slowly
into the filling hole until the cartridge is almost full.
5. Wipe the filling hole clean and dry and then insert a silicon plug. Depending on
the sealing plug you receive, you may need to widen the hole to accommodate
the new plug. Be sure to seal it air tight (not sealing it air tight could cause leakage while printing).
6. Rinse the syringe with water and dry for future use, or use with a different color
ink.
7. Follow the resetting instructions before inserting the cartridge into printer.
Note: Immediately refill any empty cartridges.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
26
CLICK HERE TO GO THE INDEX
Epson Cartridges
A Chip Resetter (sold separately) is needed for the following cartridges:
Create Hole Here
T124120, T124220, T124320, T124420, T125120, T125220, T125320,
T125420, T126120, T126220, T126320, T126420, T127120, T127220,
T127320, T127420, T128120, T128220, T128320, T128420
1. It is important to understand the sections of this cartridge before refilling. Please
study diagram closely.
2. Using the eyelet screw, create a hole (see illustration to the right). Keep the screw
centered when drilling the hole.
Cover with Tape
3. Using Tape, seal the air path to the cartridge as shown on the right.
4. Connect the needle to the syringe and fill with the correct color ink.
5. Plug the hole using the silicone or rubber plug, and then penetrate the needle
through the plug. This will create an air tight seal while refilling. Inject about 12
ml. of ink slowly into the filling hole until the cartridge is almost full. You may
need to pull back on the syringe and then push in slowly to get all the ink in.
6. Once finished remove the tape from you used to cover the air path in step 3.
7. Rinse the syringe with water and dry for future use, or use with a different color
ink.
8. Follow the resetting instructions from the resetter before inserting the cartridge
into printer.
Note: Immediately refill any empty cartridges.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
27
CLICK HERE TO GO THE INDEX
Hewlett Packard Cartridges
51626A, 51629A, 51626G, 51629G,
51633M, C6614AN, C6628AN
9. Rinse the syringe with water and dry for future use.
10. Now remove the tape over (Aerator “B”).
1. Put a piece of tape over (Aerator “B”) on the bottom of the cartridge. This aerator must
be sealed tightly to prevent leaking. - See diagram.
2. Aerator “C” is located in the center of the top of cartridge. DO NOT STICK THE
NEEDLE IN THIS HOLE.
3. If you have a cartridge that has a ball bearing in the top corner of the cartridge then
simply push in the ball bearing with a pointed object such as a screwdriver.
4. If you have a cartridge that does not have this ball bearing; a hole must be made in the
top corner of the cartridge- see diagram. Use the hole making tool included in the kit
or an exacto knife or a drill bit to make this hole. This hole must be made perfectly
round.
5. Remove the Hole Making Tool from its packaging then remove the cover from the tool
to expose the blade. CAREFUL! Blade is sharp. Firmly hold the handle of the tool and
begin twisting the tool into the top corner of the cartridge. Continue twisting until it
pierces the plastic cover. Once the plastic to is pierced, making the rest of the hole will
go very quickly.
11. If the cartridge continues to drip ink, Insert ONLY the tip (no more than
1/8 inch) of the needle into (Aerator “C”), hold the cartridge over a sink or
paper towels. Pull back on the plunger of the EMPTY syringe to 2 ml and
push down on the plunger to pump 2 ml of air into cartridge. Important: Do
NOT insert the needle more than 1/8 inch into aerator C as you will damage
the cartridge.
12. Ink will now drip from the nozzles. Blot the nozzles with the tissue until ink
stops dripping.
13. Reinsert cartridge into printer and run several test cycles until print quality
is restored.
Note: Allow the cartridge to sit outside the printer overnight to restore print
quality. Note: Immediately refill any empty cartridges.
Filling Hole
Aerator “C”
IMPORTANT: Do not make a hole as big as the tool itself. The plug provided must
fit tightly in order for a perfect air tight seal.
6. Connect the needle to the syringe and pull back on the plunger to fill with cartridge
and printhead cleaner. Inject approximately 2 ml of cleaner. It is not necessary to seal
the cartridge. Let the cartridge sit for about 2 minutes. To remove the cleaner, turn the
cartridge over and let it drain out of the filling hole.
7. Now turn the cartridge upright on a paper towel and fill with 20 ml. of ink through the
filling hole on the top corner of the cartridge.
8. Squeeze the sides of the cartridge while sealing the hole with the plug included. Optional: To insure that it is sealed airtight, cover the plug with a piece of electrical
tape.
Aerator “B”
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
28
CLICK HERE TO GO THE INDEX
Hewlett Packard Cartridges
51625A, 51649A , 51649G, C1816A
1. The plastic cover must be remove to reveal the filling holes. Carefully pry it off
with a thin metal blade, such as a thin flathead screwdriver. Or lay the cartridge on its side with the plastic cap off the edge of a table holding it firmly
then break the seal by striking it with a blunt object. Important: Make certain
that the sensors on the back of the cartridge do not get damaged.
2. Connect the needle to the syringe and fill with the correct color of ink.
Yellow
Cyan
3. Insert the needle into the hole of the color to be refilled, (see diagram above)
and push directly down into the cartridge. Note: You may feel a slight pressure due to the sponge inside the cartridge.
4. Slowly inject approximately 7 ml. of ink, per color, into the cartridge. Stop
when the ink begins to surface. Important: The sponge inside is white. And
in order to prevent overfilling the chamber, the color of the sponge must
remain white. As soon as the ink starts to bubble near the needle then stop
injecting, the cartridge is full.
5. Rinse the syringe and needle with water and dry between each color refilling or
store for future use.
6. The cover can be reconnected with a piece of adhesive tape.
Magenta
Yellow
Filling Hole
Cyan
Filling Hole
Magenta
Filling Hole
Sensors
Note: Immediately refill any cartridge that has become empty.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
29
CLICK HERE TO GO THE INDEX
Hewlett Packard Cartridges
51645A, 51645G, 51640A, 51640C, 51640M, 51640Y, 51644C,
51644M, 51644Y, C6615DN , C6615AN
1. Turn the cartridge upside down and using a peel back the plastic film covering
the stainless steel ball bearing as shown below.
2. Using a screwdriver push the ball bearing into the cartridge.
3. Connect the needle to the syringe and fill with the correct color ink. Important: Do NOT insert the needle more than 1 inch into the cartridge as you may
purchase the bag inside the cartridge.
4. Inject 20 ml. of ink into the hole.
5. Squeeze the sides of cartridge while sealing the filling hole with the included
plug, make sure that the plug is seated flush against the cartridge.
6. Allow cartridge to sit with the print head down for at least 2 minutes to draw
out any excess ink and equalize the pressure in the cartridge. Important: Do
not leave the cartridge resting on a paper towel. This will cause your cartridge to slowly empty itself..
7. Rinse the syringe with warm water and dry between each color refill or store
for future use.
8. Reinsert the cartridge and run a priming cycle as per printer instructions.
Note: Immediately refill any empty cartridges.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
30
CLICK HERE TO GO THE INDEX
Hewlett Packard Cartridges
Yellow
51641A, C1823A, C1823D, C1823G, C6625AN,
C6578AN, C6578DN, C3844A, C3845A
Magenta
Cyan
1. The small sealed holes on the top are the filling holes. Use a small screwdriver
to push the plastic seals into the cartridge.
2. Connect the needle to the syringe and fill with the color ink you are going to
fill.
3. Insert the needle into the filling hole of the color you are refilling, (see diagram
above) and push all the way towards the center of the cartridge. Note: The
cartridge contains a sponge and resistance will be felt.
4. Inject approximately 10 ml of ink, per color, or until ink just begins to bubble
at the top of the filling hole. Note: Remember to reseal the holes when your
done.
5. Clean the syringe with warm water, and dry before refilling with another color
or for future use.
Note: Empty cartridges should always be filled immediately.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
31
CLICK HERE TO GO THE INDEX
Hewlett Packard Cartridges
C4841A, C4842A, C4843A, C4844A
38, 50, 70, 72, 80, 81, 82, 83, 88, 90, 940
1. Cut label at joint between top and bottom cap of cartridge case.
2. Flip back the bottom cap of cartridge.
3. Squeeze the sides of cartridge casing and wiggle out the Mylar ink bag and
pump assembly from the insert lock.
4. Screw the eyelet screw into the center of the rubber sealing plug, (situated in
the filling hole) until a firm grip is made and pull out the plug. (Do not pull the
plug off the end of the eyelet screw.)
5. Inject the ink through the filling hole into the Mylar ink bag. Do not insert the
needle more than 1/2” into the bag or else the Mylar ink bag may be pierced.
(Black takes 20 ml of ink. Color cartridges take 10 ml of ink)
6. Fill with ink until ink appears at the bottom of the filling hole. Reseal with the
plug on the end of the screw and then remove the screw from the plug.
7. Remove the excess air from the Mylar ink bag and pump assembly as follows:
A. Hold assembly at a 45° angle with outlet hole at the top.
B. Insert needle of empty injector (with plunger pushed in) into outlet hole.
C. Press and release cartridge pump several times which will push air into the
syringe.
D. Pull back the plunger on the syringe to remove any air from the outlet hole
then remove the needle.
8. Replace the Mylar ink bag assembly into the cartridge case and clip the bottom
back into position.
After refilling, the chips have to be turned off by pushing the reset
button on the printer in for 5 seconds (This procedure may not work for all
printer models)
Note: This cartridge has a chip that knows its manufacturer date. It
lets the cartridge operate and be refilled for two years then it will stop
working. If the cartridge sat on a shelf for 6 months before you bought
it, you only have 18 months to use it and refill it as much as you want.
9. Install the cartridge back into printer.
Note: Immediately refill any empty cartridges.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
32
CLICK HERE TO GO THE INDEX
21, 22, 27, 28, 56, 57, 58, 60, 61, 61XL, 74,
74XL, 75, 75XL, 92, 93, 94, 95, 96, 97, 98, 99, 901
Hewlett Packard Cartridges
1. Peel back the label from the top of the cartridge to expose the refill
holes of the cartridge. (If the illustration on the right differ from your
cartridge model, use 3 toothpicks and poke each hole to determine its
color)
2. For high capacity cartridges (designated with the suffix “XL” such as the
HP 60xl) fill the syringe with 15 ml of black ink or 5 ml for each color
on color cartridges. For standard capacity cartridges (such as the regular HP 60), fill the syringe with 7.5 ml of black ink or 3.5 ml for each
color on the color cartridges. It is always best to under fill rather than
overfill a cartridge.
Cartridge Model #’s
21/27/56/74/74XL
92/94/96/98
Cartridge Model #’s
60/61/61XL/75/
75XL/93/95/97/110/
901
Cartridge Model #’s
22/28/57
BLACK
YELLOW
MAGENTA
MAGENTA
CYAN
YELLOW
CYAN
3. Be careful to inject the ink slowly, and if you notice that the cartridge
is getting full, don’t overfill it. Some cartridges may hold less ink than
others due to factors such as the wear and tear on the internal sponge
and the capacity of the cartridge itself.
IMPORTANT: When refilling, only puncture the top of the sponge in
the cartridge, about 1/8 to 1/4 inch. Puncturing to the bottom may
cause leakage in the cartridge.
4. Stick the label back in place, if the label has been destroyed, use duct
tape or electrical tape. (Try keeping the label size when using tape)
Cartridge Model #’s
99
Cartridge Model #’s
58
BLACK
LIGHT
MAGENTA
5. Rinse the syringe with water and dry between each color refill or store
for future use.
6. Reinstall the cartridge and run 1 - 3 test pages as per printer instructions. If necessary leave the cartridge in printer for up to 24 hours to
allow ink to flow to the print head.
Cartridge Model #’s
60, 61, 61XL, 901
BLACK
LIGHT
MAGENTA
LIGHT
CYAN
BLACK
LIGHT
CYAN
NOTE: Cartridges that are not refilled right away may and can dry with time. For the best
results, refill right after the cartridges are depleted.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
33
CLICK HERE TO GO THE INDEX
HP Cartridges
HP 701
1. Peel back the label from the top of the cartridge to expose the vent hole of
the cartridge.
2. Fill the syringe with 15 ml of black ink (5 ml for each color on color cartridges).
3. If the vent hole is to small, use the provided drill to increase the width. Be
sure to only drill through the plastic and not the sponge. Then insert the
needle into the cartridge and fill slowly. If to much ink is inserted, pull back
on the syringe handle to pull 1 ml out.
IMPORTANT: When refilling, only puncture the top of the sponge in the
cartridge, about 1/8 to 1/4 inch. Puncturing to the bottom may cause leakage in the cartridge.
4. Stick the label back in place, if the label has been destroyed, use duct tape or
electrical tape (Tape is optional).
5. Rinse the syringe with water and prepare it for storage.
6. Reinstall the cartridge and run 1 - 3 test pages as per printer instructions.
If necessary leave the cartridge in printer for up to 24 hours to allow ink to
flow to the print head.
NOTE: Cartridges that are not refilled right away may and can dry with time.
For the best results, refill right after the cartridges are depleted.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
34
CLICK HERE TO GO THE INDEX
HP Cartridges
Refill Hole
(Ball Bearing)
Air Vent
HP 564 and 920
1. Use electrical or duct tape to seal the Air Vent found on the top of the cartridge.
Note: Make sure tape is completely covering the vent.
2. Remove the label partially, only to expose the ball bearing underneath. Then use a screwdriver or an L tool to push the ball bearing into the cartridge. This will give access to the
filling hole.
3. Connect the needle to the syringe and fill with ink.
4. Use your finger as a plug by covering the outlet port. Keep your finger on the outlet port
until you have finished refilling and the refill hole is plugged. If you let go any time earlier,
ink may and can spill out of that outlet.
5. Inject about 10 ml. of ink into the filling hole or until the ink chamber is full. Be sure to
leave enough room in the ink chamber for the silicon plug, it will create pressure when
inserted.
Sponge Chamber
6. Put a silicone plug in the refill hole to seal it, make sure it is air tight. If extra silicone from
the plug is sticking out, you may trim it down to a practical size. Be sure to leave enough
to make it easy for you to remove the next time you wish to refill the cartridge.
Outlet Port
Ink Chamber
Push in the ball bearing (may
require some force)
7. Remove your finger from the outlet (small drops may leak out, but once the cartridge pressure stabilizes itself, it will stop) and remove the tape from earlier off the vent.
8. Rinse the syringe with water and dry for future use, or use with a different color ink.
9. Reinsert the cartridge and run a priming cycle as per printer instructions.
Note: If the cartridge continuously leaks, place the cartridge on its side until the dripping
stops. Also, check the seal on the cartridge to make sure it is airtight.
Method 2. If you feel that the first method of refilling is not something you’d like to try, you can place ink into the cartridge via the nozzle. By turning the
cartridge over so that the nozzle (Outlet Port) points up, you can slowly drip ink into the nozzle. This procedure may take long and no ink will go into the ink
chamber, but the sponge will retain some ink for you to use and continue the use of your cartridge. You may usually use about 3-4 ml of ink at a time in the
sponge.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
35
CLICK HERE TO GO THE INDEX
Hewlett Packard Cartridges
C1806A, C1807A, C1808A, C1809A
1. Remove the Mylar ink bag from the cardboard covering. Note: (This Mylar
ink bag is very delicate and must be handled with care).
2. Use both hands when holding the top of the Mylar bag and use both thumbs
to pry the hose cap off of the connector. (Pop off the connector the same way
you would pop off the cap of an aspirin bottle. Be very careful not to damage
the connector.) Make certain not to misplace or damage the O-ring. It must be
in the same position shown below before the hose cap assembly can be reinstalled.
Assembly
Connector
Mylar Bag
Base of
Connector
3. Connect the needle to the syringe and fill with ink.
4. Hold the bag upright and inject up to 60 ml of ink or until 3/4 full. Do not
fill completely because you need room to install the hose cap assembly. Note:
(After filling do not squeeze the Mylar bag as this will cause ink to squirt out
of the connector.
5. Hold the top of the Mylar bag and using both thumbs reinstall the hose cap
assembly. You can grasp the block at the base where the assembly is installed
into the Mylar bag. Make sure the hose cap assembly is firmly attached to the
connector. You will feel two clicks when reinstalling the hose cap assembly.
Hose Cap
Assembly
Connector
6. Put the Mylar bag back into the cardboard covering and install into machine.
7. Rinse the syringe and needle with water between each color refilling and dry
for future use.
O-Ring
Note: Empty cartridges should be refilled immediately.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
36
CLICK HERE TO GO THE INDEX
Hewlett Packard Cartridges
C5010A, C5011A
1. Connect the needle to the syringe. Using the needle, pierce through the label
into the cartridge. Note: We have removed the label to illustrate where the
filling holes are located. We do not recommend removing it.
Magenta
Yellow
2. After you have pierced the label, fill the syringe with the correct color of ink.
3. Insert the needle into the cartridge of the filling hole. Slowly inject ink into the
cartridge is full. Use approximately 5 ml per chamber.
4. Use a piece of tape to seal the hole(s) made in the top label. Note: The cartridge will leak if the holes are not sealed properly.
5. Rinse the syringe with water and dry between each color refill or store for
further use.
6. Reinstall the cartridge and run 1 - 3 test pages as per printer instructions. If
necessary leave cartridge in printer for up to 24 hours to allow ink to flow to
the print head.
Cyan
NOTE: This time is greatly reduced if the cartridge is refilled before it is completely empty.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
37
CLICK HERE TO GO THE INDEX
Hewlett Packard Cartridges
C6634A, C6635A
1. Drill filling holes on the top of the cartridge (as shown below left) or pry off
the cartridge top as shown below right. Do the procedure that is easier for you.
Use the hole making tool included in the kit, drill each filling hole on the top
of the cartridge wide enough to fit the needle as shown below left. Or use a flathead screwdriver to pry off the top.
Black
2. Connect the needle to the syringe and fill with the ink. Note: All 3 filing holes
must be refilled in the black cartridge.
3. Insert the syringe through the filling hole and push all the way into the cartridge. Note: You may feel a slight pressure because the cartridge contains a
sponge.
4. Slowly inject up to 6 ml. of ink, per chamber, then seal the filling holes using a
piece of tape.
5. Rinse the syringe with water and dry for future use, or use with a different
color ink.
6. Reinsert the cartridge(s) and run a test page as per printer instructions.
Note: Immediately refill any empty cartridges.
Magenta
Cyan
Yellow
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
38
CLICK HERE TO GO THE INDEX
Hewlett Packard Cartridges
Refilling the Black Cartridge:
1. Use the enclosed eyelet screw to create the filling hole at the top of the cartridge. Picture
A, on the right, illustrates where the refill hole should be created.
2. Fill the syringe with ink. Insert the needle into the filling hole and push down into the cartridge. Inject up to 9 ml of ink into the cartridge. It is always better to under fill than over
fill any cartridge. You can always add more ink later.
NOTE: On OEM HP cartridges, there is a small dimple located near the
HP emblem as illustrated on picture B. If this dimple is on your
OEM HP cartridges, please create the refilling hole through it
Picture B shows a refilling hole which was created through the dimple
of a yellow HP OEM cartridge.
A
Refill hole
Refill hole
B
3. Once your cartridge has been filled, remove the needle from the cartridge and plug the top
of the cartridge with the plugs provided in your refill kit. Please make sure to seal the plug
tight so that no extra air goes in our out of the cartridge as it prints. You will also avoid
any spills as well.
Refilling the Color Cartridges:
1. Use the enclosed eyelet screw to create the filling hole at the top of the cartridge. Picture B,
on the right, illustrates where the refill hole should be created.
2. Fill the syringe with ink. Insert the needle into the filling hole and push down into the
cartridge. Inject up to 4 ml of ink into the cartridge. It is always good practice to under fill
than over fill any cartridge. You can always add more ink later.
3. Once your cartridge has been filled, remove the needle from the cartridge and plug the top
of the cartridge with the plugs provided in your refill kit. Please make sure to seal the plug
tight so that no extra air goes in our out of the cartridge as it prints. You will also avoid
any as well.
Reinstalling the Cartridges
Reinstalling:
1. Open the lid to your printer.
2. Place your refilled cartridge into the cradle that corresponds with the color of the
tank.
3. Close the lid to your printer.
4. A prompt will then display on your printer screen saying “Original HP Ink Depleted”.
5. On your printer will be a circle of buttons with “OK” in the middle and arrow
keys. Press the right arrow key.
6. A prompt will then display on your printer screen saying “Attention”.
7. Press the “OK” button on your printer.
NOTE: The ink levels will not show on the screen. However, once the volume of
ink has been depleted from the replaced tank, the printer will not allow you to
print any further until the tank has been refilled again.
Some printers may require a new chip after refill
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
39
Hewlett Packard Cartridges
932, 933, 950, 951
CLICK HERE TO GO THE INDEX
Method A
1. Locate the “Fill Port” on your cartridge.
2. You should see a plastic ball in this “Fill Port”. Use a allen wrench, or a small screw driver with a hammer, to gently
knock the plastic ball into the cartridge.
3. Connect the needle to the syringe and fill with ink.
4. Inject about 10-15 ml. of ink into the filling hole or until the ink chamber is full. Be sure to leave enough room in the
ink chamber for the new plug, it will create pressure when
inserted.
Fill Port
5. Seal the hole. Make sure the seal is air tight. If your plug is sticking out to much, cut it down to size and use electrical
or duct tape to help secure the plug in place.
6. Rinse the syringe with water and dry for future use, or use with a different color ink.
7. Reinsert the cartridge and run a priming cycle as per printer instructions.
1. Locate the “Nozzle” on your cartridge.
Method B
2. Connect the cannula needle to the syringe and fill with ink.
3. Inject about 10-15 ml. of ink into the cartridge or until the ink chamber is full. If you feel
a little pressure, pull back on the syringe handle to pull some air out, and then continue
filling (repeat this process as needed).
4. Once finished, pull back on the sryinge handle a little while its still in the nozzle, to help
prime the cartridge and get it ready to use.
Nozzle
5. Remove the syringe from the cartridge, rinse it with water and dry for future use, or use
with a different color ink.
6. Reinsert the cartridge and run a priming cycle as per printer instructions.
Note: You may want to refer to your printer manual to turn off usage information. This
allows you to continue using your newly refilled cartridge.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
40
Hewlett Packard Cartridges
CLICK HERE TO GO THE INDEX
Chip Replacement
This illustration shows the cartridge sitting in its
upright position. The chip is located on the bottom part of the cartridge. Although this cartridge
may sit in a certain position in your printer, this
would be considered the correct upright position.
The illustration above is the bottom part
of the cartridge. The chip is located on the
right side in this example. To remove it, you
will need a small flat head screwdriver. When
ready, pry the chip from the cartridge.
Once you have removed the chip, replace
it with the new chip you purchased. Some
chips may have a tape backing that you can
just peel off and easily place it on the cartridge, others may need to be glued onto the
cartridge. Once its replaced, print a test page
and check the ink levels.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
41
Kodak Cartridges
CLICK HERE TO GO THE INDEX
#10 (Black and Color)
1. Peel back the sticker at the top of the cartridge to reveal refilling holes. (See picture’s
to the right)
Black
2. Connect the needle to the syringe and fill the syringe with 10 ml of ink for the Black
cartridge or 5 ml of ink for each of the colors in the color cartridge.
3. Insert the needle into the filling hole and push down into the cartridge. (Only push
down about 1/4 of an inch). Fill the cartridge with the proper color and then clean
the syringe with water before moving on to the next color. (Do not cross contaminate colors. Cleaning the syringe is a must before filling it with the next color).
4. Once your done refilling, try the chip installation chip below before inserting the
cartridge into the printer.
*Chip installation instructions*
Newly refilled Kodak ink cartridges need to have their chips replaced with new
chips so that the printer can “recognize” them as full again.
Aftermarket chips are slightly different in shape to the original chips in order
to better protect them from damage (replacement chips are slightly thicker),
and therefore it is required to modify the chip slot on the cartridge to adequately hold the replacement chip in place.
Black
Cyan
Magenta
Glossy
Yellow
1. You will notice that the OEM (original) chip is held in place by a small
plastic protrusion that is holding the chip in place from the bottom of the
chip (see just below the chip, in the middle of the chip). This plastic protrusion can be depressed easily with a screwdriver or pen tip, releasing
the hold on the chip. The chip will then easily slide downwards,and out.
2. The replacement chip is thicker than the original chip, so the same
plastic protrusion needs to be depressed even more in order to get the
replacement chip to slide in place. The protrusion may need to be physically bent a little to create the extra space needed to slide the chip place.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
42
CLICK HERE TO GO THE INDEX
Lexmark Cartridges
M = Magenta
Y = Yellow
C = Cyan
Black Cartridges:
10N0016, 10N0217, 12A1970, 12A1975, 1361400, 13400HC, 1380620,
1382050, 15M2971, 16G0055, 17G0050, 18L0032,
1. Use the enclosed eyelet screw to enlarge the filling hole located at the top of the
cartridge. (Do not remove the cap.)
2. Connect the needle to the syringe and fill the syringe with 8 ml. of Cartridge
& Print Head Cleaner and inject into the cartridge. Reinsert cartridge into
printer and print 5 test pages.
Sensors
3. Fill the syringe with ink. Insert the needle into the filling hole and push down
into the cartridge. Inject up to 20 ml. of ink or until the cartridge is full.
Magenta
Yellow
Note: Immediately refill any empty cartridges.
Color Cartridges:
12A1980, 12A1985, 1380619, 10N0026, 10N0027, 15M0120, 15M0125,
18L0042, 1382060, 17G0060, 16G0065
Cyan
Photo cartridges:
12A1990, 1361760
Filling Hole
1. The filling holes are located under the plastic cap. Use a thin flathead screw
driver or knife to remove the cap. Important: Do not to damage the sensors on
the back of the cartridge.
4. Inject about 8 ml. of ink, per color, into the cartridge until the ink
begins to bubble at the top of the sponge. Important: Do not overfill.
Keep the sponge inside the cartridge white.
2. Connect the needle to the syringe and fill with ink.
5. Rinse the needle and syringe with water and dry between each color
refilling or store for future use.
3. Insert the needle into the matching hole of the color to be refilled, (see diagram
above) and push into the cartridge. Note: You will feel a slight pressure because
the cartridge contains a sponge.
6. The cover can be reattached with a piece of tape.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
43
CLICK HERE TO GO THE INDEX
Lexmark Cartridges
1380490, 1380491, 1380492, 1380493
1. The filling hole is the same hole as the hole that connects to the printer.
2. Note: The cartridge is lined in a delicate Mylar bag and it is very important not
to insert the needle more than 3/4” or it is possible to pierce or tear the Mylar
bag. Fill the syringe with the correct color ink and carefully insert the needle Front of
Cartridge
into the filling hole and slowly inject approximately 90 ml. of ink into the
cartridge.
Filling Hole
Waste
Ink Port
3. Hold the cartridge upright with the filling hole at the top. Using the syringe,
remove any trapped air in the cartridge by only inserting the tip of the needle
and pulling up on the plunger until all air is removed.
4. Remove the syringe and rinse with water and dry for future use, or to use with
a different color ink.
5. Reinsert the cartridge and run a priming cycle as per printer instructions.
Note: Immediately refill any empty cartridges.
NOTE: It is not necessary to disassemble the cartridge to refill it and we strongly
recommend you do not. We have included a picture of the inside of the cartridge
to satisfy your curiosity.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
44
CLICK HERE TO GO THE INDEX
Lexmark Cartridges
18C0031, 18C0032, 18C0033, 18C0034, 18C0035
Black Cartridges:
1. Use the enclosed eyelet screw to enlarge the filling hole located at the top of the
cartridge. (Do not remove the cap.)
2. Connect the needle to the syringe and fill the syringe with 8 ml. of Cartridge &
Print Head Cleaner and inject into the cartridge. Reinsert cartridge into printer
and print 5 test pages.
3. Fill the syringe with ink. Insert the needle into the filling hole and push down into
the cartridge. Inject up to 20 ml. of ink or until the cartridge is full. Note: Immediately refill any empty cartridges.
Magenta
Color Cartridges:
1. The filling holes are located under the plastic cap. Use a thin flathead screwdriver
or knife to remove the cap. Important: Do not to damage the sensors on the back
of the cartridge.
2. Connect the needle to the syringe and fill with ink.
3. Insert the needle into the matching hole of the color to be refilled, (see diagram
above) and push into the cartridge. Note: You will feel a slight pressure because the
cartridge contains a sponge.
4. Inject about 8 ml. of ink, per color, into the cartridge until the ink begins to bubble
at the top of the sponge. Important: Do not overfill. Keep the sponge inside the
cartridge white.
5. Rinse the needle and syringe with water and dry between each color refilling or
store for future use.
6. The cover can be reattached with a piece of tape.
Cyan
Yellow
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
45
CLICK HERE TO GO THE INDEX
Lexmark Cartridges / Dell Cartridges
1. Peel back the label from the top of the cartridge to expose the refill
holes of the cartridge. (If the illustration on the right differ from
your cartridge model, use 3 toothpicks and poke each hole to determine its color)
2. Fill the syringe with 15 ml of black ink (5 ml for each color on
color cartridges).
3. Insert the needle into the cartridge (corresponding with the correct color ink) and fill. If to much ink is inserted, pull back on the
syringe handle to pull 1 ml out.
DELL
MK990, MK992,
Series 5 , Series 7, Series 8,
Series 9, Series 15,Series 11
LEXMARK
#3, #4A, #14A, #23A, #28A, #32,
#34, #36A, #42A, #44
BLACK
DELL
MK991, MK993,
Series 5, Series 7, Series 8,
Series 9, Series 15,Series 11
LEXMARK
#1, #2, #5A, #15A, #24A, #29A, #33,
#35, #37A, #41A. #43
MAGENTA
IMPORTANT: When refilling, only puncture the top of the sponge
in the cartridge, about 1/8 to 1/4 inch. Puncturing to the bottom
may cause leakage in the cartridge.
4. The cartridge will function better keeping the label off the top of
the cartridge, allowing air to enter the cartridge from the top and
thereby allowing ink to flow better through the cartridge. Keep the
top of the cartridge exposed to air (do not put tape over the holes).
Make sure to keep the cartridges up right when transporting them
back to the printer
YELLOW
CYAN
5. Rinse the syringe with water and dry between each color refill or
store for future use.
6. Reinstall the cartridge and run 1 - 3 test pages as per printer instructions. If necessary leave the cartridge in printer for up to 24
hours to allow ink to flow to the print head.
NOTE: Cartridges that are not refilled right away may and can dry
with time. For the best results, refill right after the cartridges are depleted.
NOTE: If your cartridge is part of Lexmark’s recycle program, then the refilling holes might not be
viewable. In this case you can drill a hole in the
same area’s indicated above to refill the cartridge.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
46
Lexmark Cartridges / Dell Cartridges
Items needed: gloves, hand-drill, cartridges, paper towels.
Note: You will need the Lexmark 100A version. Some models may require a new replacment
chip to succesfully reset the cartridge.
CLICK HERE TO GO THE INDEX
LEXMARK 100A, 108A, 150A, 200A
Lexmark offers for sale two different versions of the same cartridge: The regular version
(#100) is not refillable. It is the “Return Program” or “Rebate” cartridge. Supposedly,
when you buy this cartridge you agree to return the empty cartridge to Lexmark. In
return, Lexmark gives you roughly $5 off the retail list price of the cartridge. The “A”
version (#100A) can easily be refilled. However, the price of the cartridge is roughly $5
higher than the regular version, so most people unknowingly buy the regular version. If
you want to refill, you will need “A” version cartridges.
Pierce needle here
1. Put the cartridge on some paper towels in an area where you can tolerate a spill.
2. Fill the syringe with 12 ml. of black ink or 5 ml of Color Ink .
4. Push the needle at least half way down into the sponge and Very SLOWLY inject ink
into the sponge.
5. When finished, leave the pierced hole open (this will just be a vent hole).
6. Replace the cartridge and run 1 - 3 cleaning cycles as per printer instructions.
Or print the following pages:
For best results, leave cartridge in printer for 8 hours after refilling so the ink can saturate the entire sponge.
Chip Replacement Option
To replace the chip, peel back the top
label until the chip is fully exposed.
Pry it from its current position, remove
it, and then replace it with a new one in
the same orientation as the original or
previous chip.
CHIP
3. Pierce with the needle into the label where black meets white. (You can rub your
finger over the label and feel the hole underneath.) See illustration.
Once the chip has been replaced, place
the label back on the cartridge. Your cartridge should be ready for use.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
47
CLICK HERE TO GO THE INDEX
Okidata Cartridges
Black Cartridge:
52109301
1. Use the enclosed eyelet screw to enlarge the filling hole located at the top of the cartridge. (Do not remove the cap.)
2. Connect the needle to the syringe and fill the syringe with 8 ml. of Cartridge & Print
Head Cleaner and inject into the cartridge. Reinsert cartridge into printer and print 5
test pages.
3. Fill the syringe with ink. Insert the needle into the filling hole and push down into the
cartridge. Inject up to 20 ml. of ink or until the cartridge is full. Note: Immediately
refill any empty cartridges.
Color Cartridge:
52109302
1. The filling holes are located under the plastic cap. Use a thin flathead screw driver or
knife to remove the cap. Important: Do not to damage the sensors on the back of the
cartridge.
Cyan
Yellow
Magenta
2. Connect the needle to the syringe and fill with ink.
3. Insert the needle into the matching hole of the color to be refilled, (see diagram above)
and push into the cartridge. Note: You will feel a slight pressure because the cartridge contains a sponge.
4. Inject about 8 ml. of ink, per color, into the cartridge until the ink begins to bubble at
the top of the sponge. Important: Do not overfill. Keep the sponge inside the cartridge white.
5. Rinse the needle and syringe with water and dry between each color refilling or store
for future use.
6. The cover can be reattached with a piece of tape.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
48
CLICK HERE TO GO THE INDEX
Okidata Cartridges
52110001, 52110002, 52110003, 52110004
1. The filling hole is located under the label as shown. Just peel back the label
leaving it still connected to the cartridge, do not remove completely.
Filling hole
2. Use the provided eyelet screw to drill a filling hole on the top of the
cartridge(s) opposite side of the sponge.
3. Connect the needle to the syringe and fill with ink.
4. Insert the needle into the filling hole and inject about 5 ml of ink.
5. Use the provided plug to seal the hole. Note: If the cartridge has been empty/
dry, the sponge will no longer accept any ink which will cause the cartridge
to leak. Pull the label back into place and use a piece of tape to hold it in place.
6. Rinse the syringe with water and dry between each color refill or store for
future use.
7. Reinsert cartridge back into the printer and run 1 - 3 cleaning cycles as per
printer instructions.
Note: Immediately refill any empty cartridges
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
49
CLICK HERE TO GO THE INDEX
Pitney Bowes Cartridge
Outlet hole
769-0
1. Put a piece of tape over the exit hole located on the bottom of the cartridge
2. The filling hole is located on the back of the cartridge and must be widen using
the included eyelet screw
3. Connect the needle to the syringe and fill with FLUORESCENT RED ink.
4. Insert the syringe into the filling hole all the way down into the cartridge.
Note: This cartridge contains a sponge so you may feel a slight pressure.
Filling hole
5. Use your thumb to hold the tape in place while injecting 4 ml. of ink into the
cartridge.
6. Rinse the syringe with water and dry for future use.
7. Reinsert the cartridge(s) and run a cleaning cycle as per postage machines
instructions.
Note: Immediately refill any empty cartridges.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
50
CLICK HERE TO GO THE INDEX
Sharp Cartridges
Black Cartridges:
AJ-C50B, UX-C70B
1. Use the enclosed eyelet screw to enlarge the filling hole located at the top of
the cartridge. (Do not remove the cap.)
2. Connect the needle to the syringe and fill the syringe with 8 ml. of Cartridge
& Print Head Cleaner and inject into the cartridge. Reinsert cartridge into
printer and print 5 test pages.
3. Fill the syringe with ink. Insert the needle into the filling hole and push down
into the cartridge. Inject up to 20 ml. of ink or until the cartridge is full. Note:
Immediately refill any empty cartridges
Filling Hole
Color Cartridge:
AJ-C50C
1. The filling holes are located under the plastic cap. Use a thin flathead screwdriver or knife to remove the cap. Important: Do not to damage the sensors
on the back of the cartridge.
2. Connect the needle to the syringe and fill with ink.
3. Insert the needle into the matching hole of the color to be refilled, (see diagram above) and push into the cartridge. Note: You will feel a slight pressure
because the cartridge contains a sponge.
4. Inject about 8 ml. of ink, per color, into the cartridge until the ink begins to
bubble at the top of the sponge. Important: Do not overfill. Keep the sponge
inside the cartridge white.
5. Rinse the needle and syringe with water and dry between each color refilling
or store for future use.
6. The cover can be reattached with a piece of tape.
Sensors
Magenta
Yellow
Cyan
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
51
CLICK HERE TO GO THE INDEX
Color Cartridges:
8R12591, 8R7880, 8R882
Xerox Cartridges
Sensors
Magenta
1. The filling holes are located under the plastic cap. Use a thin flathead screw\driver or
knife to remove the cap. Important: Do not to damage the sensors on the back of
the cartridge.
Yellow
2. Connect the needle to the syringe and fill with ink.
3. Insert the needle into the matching hole of the color to be refilled, (see diagram
above) and push into the cartridge. Note: You will feel a slight pressure because the
cartridge contains a sponge.
4. Inject about 8 ml. of ink, per color, into the cartridge until the ink begins to bubble
at the top of the sponge. Important: Do not overfill. Keep the sponge inside the
cartridge white.
Cyan
5. Rinse the needle and syringe with water and dry between each color refilling or store
for future use.
6. The cover can be reattached with a piece of tape
Black Cartridges:
8R7881
1. Use the enclosed eyelet screw to enlarge the filling hole located at the top of the cartridge. (Do not remove the cap.)
2. Connect the needle to the syringe and fill the syringe with 8 ml. of Cartridge & Print
Head Cleaner and inject into the cartridge. Reinsert cartridge into printer and print
5 test pages.
3. Fill the syringe with ink. Insert the needle into the filling hole and push down into
the cartridge. Inject up to 20 ml. of ink or until the cartridge is full.
Filling Hole
Note: Immediately refill any empty cartridges.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
52
CLICK HERE TO GO THE INDEX
Xerox Cartridges
8R7660, 8R7661, 8R7662, 8R7663
1. The filling hole is located under the label as shown. Just peel back the label
leaving it still connected to the cartridge, do not remove completely.
2. Use the provided eyelet screw to drill a filling hole on the top of the
cartridge(s) opposite side of the sponge.
3. Connect the needle to the syringe and fill with ink.
4. Insert the needle into the filling hole and inject about 5 ml of ink.
5. Use the provided plug to seal the hole. Note: If the cartridge has been empty/
dry, the sponge will no longer accept any ink which will cause the cartridge
to leak. Pull the label back into place and use a piece of tape to hold it in place.
6. Rinse the syringe with water and dry between each color refill or store for
future use.
7. Reinsert cartridge back into the printer and run 1 - 3 cleaning cycles as per
printer instructions.
Note: Immediately refill any empty cartridges
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
53
CLICK HERE TO GO THE INDEX
Xerox Cartridges
8R7638
1. Using the included hole making tool make a filling hole in the front of the
cartridge about 1/2” from the top.
2. Connect the needle to the syringe and fill with ink.
3. Insert the filling needle into the hole and aim it towards the center of the cartridge.
Note: The cartridge contains a dense sponge made out of felt. As soon as
the needle touches the felt stop pushing in the needle.
4. Inject up to 40 ml. of ink or until ink bubbles at the filling hole.
5. Use either the plug included in the kit or a piece of tape to seal the filling hole.
6. Rinse the syringe and needle with water and dry for future use.
7. Reinsert the cartridge and run a priming cycle as per printer instructions.
Note: Empty cartridges should be refilled immediately.
Make 1/8” /3mm
filling hole
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
54
CLICK HERE TO GO THE INDEX
Xerox Cartridges
Plastic
Cover
Sensors
8R7903, 8R7904
1. The filling holes are located under the plastic cap. The cap is held in place with
a pin at the each corner. Use a thin flathead screwdriver or knife to remove the
cap. Important: Do not to damage the sensors on the back of the cartridge.
2. Connect the needle to the syringe and fill with ink.
3. Insert the needle into the matching hole of the color to be refilled, (see diagram above) and push into the cartridge. Note: You will feel a slight pressure
because the cartridge contains a sponge.
4. Inject about 10 ml. of ink, per color, into the cartridge until the ink begins to
bubble at the top of the sponge. Important: Do not overfill. Keep the sponge
inside the cartridge white.
5. Rinse the needle and syringe with water and dry between each color refilling
or store for future use.
Cyan
Unused Filling hole
Yellow
Black
6. The cover can be put back onto the cartridge by pressing it down.
Magenta
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
55
CLICK HERE TO GO THE INDEX
Xerox Cartridges
Top and body
of cartridge
8R12728
1. Use the eyelet screw to make the filling hole in the small notch on the corner
located next to the “1” shown on the label.
2. Fill the syringe with ink and inject about 8 ml. of ink until the ink tank is full.
3. Use a piece of tape to seal the filling hole, make sure that the tape is stuck to
the cartridge.
4. Rinse the syringe with water and dry for future use, or use with a different
color ink.
5. Reinsert the cartridge and run a priming cycle as per printer instructions.
Note: Immediately refill any empty cartridges.
Filling Hole
Under Label
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
56
CLICK HERE TO GO THE INDEX
Xerox Cartridges
Top and body
of cartridge
8R7971, 8R7972, 8R7973, 8R7974
1. The filling hole is located under the label on the top of the cartridge. Use the
empty needle to pierce through the label to make the filling hole.
2. Fill the syringe with ink and inject about 4 ml. of ink until the ink tank is full.
3. Use a piece of tape to seal the filling hole, make sure that the tape is stuck to
the cartridge
4. Rinse the syringe with water and dry for future use, or use with a different
color ink.
5. Reinsert the cartridge and run a priming cycle as per printer instructions.
Note: Immediately refill any empty cartridges.
Filling Hole
Under Label
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
57
CLICK HERE TO GO THE INDEX
Pitney Bowes
793-5
1. Peel off the sticker on the top front of the cartridge (original Pitney Bowes
cartridges have a sticker that covers the entire top side of the cartridge, whereas
NuPost Compatible cartridges have a smaller sticker).
2. Underneath the sticker, you will notice at least 1 hole. Locate the hole that is
covered by a silver foil seal tab, this silver seal covers the filling hole. (If you do
not see this hole in your cartridge, please use the illustration to your right to
create a hole to refill the cartridge).
3. Attach the needle to the syringe and draw up 8 ml of compatible ink.
4. Either insert the needle through the silver seal, or remove the seal first using
a small knife or blade and then insert the needle through the filling hole. (do
NOT insert the needle through any hole that has a rubber protrusion, as indicated by the lower hole in this Nupost compatible cartridge). The filling hole
should provide no initial resistance to your needle other than the seal that lies
above it. Once you insert the needle into the cartridge, you will begin to feel
some resistance due to the sponge inside the cartridge, it is OK to penetrate
this sponge. Push the needle gently through to the bottom of the sponge, and
inject about 8 ml of ink or until the cartridge is full. You will know the cartridge is full because the sponge will no longer be able to hold any more ink.
Create refill hole here
5. Seal the filling hole with electrical tape, and allow the cartridge to sit for a few
minutes over some paper towels in order to allow the ink to settle to the bottom of the cartridge, and for any overflow to drip and settle its way out through
the bottom. Once the cartridge is no longer dripping, you can place it back in
the printer.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
58
797-0
Pitney Bowes
CLICK HERE TO GO THE INDEX
1. SKIP THIS STEP if your cartridge is not a Pitney Bowes original cartridge. The original PB
cartridges have a cap which needs to be removed. Using a medium sized flat screwdriver,
lift the tab as shown in the picture. Once the tab has cleared the top of the cartridge, slide
the cap away from you until it is completely removed from the cartridge.
2. Remove the circular silver seal tabs (not necessary for Nupost compatible cartridges). Pay
careful attention to both areas exposed by removing the silver seals, you will notice that 1
are actually has 2 holes right next to each other, whereas the other area only has 1 hole. In
the area that has 2 holes next to each other, make sure NOT to put ink into the outer hole,
as that is a vent hole and any ink poured in there will leak out the bottom of the cartridge.
3. FOR PITNEY BOWES ORIGINAL CARTRIDGES: Enlarge the 2 filling holes (the one on
the right of the picture shown, and the INNER of the 2 holes on the left of the cartridge as
shown). You can enlarge these holes using an eyelet screw or a small drill bit. Note that you
need to fill BOTH filling holes with ink in order for the cartridge to work. FOR NUPOST
COMPATIBLE CARTRIDGES: There are 2 filling holes, the one is a self-sealing rubber
hole in the middle of the circle on the left, and the other is to the right of the picture which
needs to be enlarged with an eyelet screw or small drill. Both these holes (the larger self
sealing hole on the left, as well as the hole you have enlarged on the right) need to be filled with
ink.
4. Draw up compatible ink in the syringe, and fill both chambers as positioned in point 4 above.
The larger chamber on the left will hold more ink. Do NOT overfill the chambers, especially
the right chamber. If you have filled it to the brink, carefully remove a small amount of ink to
avoid it spilling. You will know when each chamber is full because you will see the ink coming to the top. Stop short of the top for both chambers to avoid spillage.
5. Cover both filling holes with electrical tape, making sure to leave the middle vent hole open
on the Nupost model as shown below.
6. Replace the cap of the cartridge (not needed for Nupost model). If the cartridge is dripping ink,
place it on some paper towels until it has pressurized and stopped dripping. Now you can place
it back in the Pitney Bowes meter.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
59
Pitney Bowes
CLICK HERE TO GO THE INDEX
765-0
1. Locate the filling hole in the center of the rubber plug as shown in
the image below. For Nupost models, this filling hole is covered by a
silver seal. You can poke through the silver seal with the syringe and
needle.
2. Inject approximately 25 ml into the cartridge, being careful not to
overfill.
3. Place the cartridge back into the mailing machine and run a test
cycle. Prompt your machine to let it know that you have inserted a
new cartridge.
© All rights reserved, Easy Group, LLC. Version 4.2
All trademarks are property of their respective owners. Uni-Kit® has no association with any of the manufacturers listed here such as Hp, Epson, Lexmark, Xerox, etc.
All logos and brand names shown here are used for identification purposes only. It is illegal to reproduce these instructions without written licensing consent from Easy Group LLC.
60