Denon 1910 - AVR AV Receiver Owner`s manual

AV SURROUND RECEIVER
AVR-1910
Owner’s Manual
Manuel de l’Utilisateur
bThe illustrations used for explaining operations in this manual show the buttons of
the remote control unit.
The same operations can be performed using the buttons with the same names on
the main unit panel.
b Les illustrations des boutons présentes dans ce manuel servent à expliquer le
fonctionnement de la télécommande.
Vous pouvez contrôler l’appareil à l’aide du bouton portant le même nom sur la
façade de l’appareil.
ENGLISH FRANCAIS
nSAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
HOT SURFACE. DO NOT TOUCH.
The top surface over the internal heat sink may become
hot when operating this product continuously.
PRECAUTION:
SURFACE CHAUDE. NE PAS TOUCHER.
La surface supérieure du dissipateur de chaleur peut
devenir chaude si vous utilisez ce produit en continu.
I
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
IMPOTANT SAFETY
INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
15. Batteries shall not be exposed to excessive heat such as sunshine, fire or
the like.
CAUTION:
•The ventilation should not be impeded by covering the ventilation
openings with items, such as newspapers, tablecloths, curtains,
etc.
•No naked flame sources, such as lighted candles, should be
placed on the unit.
•Observe and follow local regulations regarding battery disposal.
•Do not expose the unit to dripping or splashing fluids.
•Do not place objects filled with liquids, such as vases, on the
unit.
ATTENTION:
•La ventilation ne doit pas être gênée en recouvrant les ouvertures
de la ventilation avec des objets tels que journaux, rideaux, tissus,
etc.
•Aucune flamme nue, par exemple une bougie, ne doit être placée
sur l’appareil.
•Veillez à respecter les lois en vigueur lorsque vous jetez les piles
usagées.
•L’appareil ne doit pas être exposé à l’eau ou à l’humidité.
•Ne pas poser d’objet contenant du liquide, par exemple un vase,
sur l’appareil.
CAUTION:
To completely disconnect this product from the mains, disconnect
the plug from the wall socket outlet.
The mains plug is used to completely interrupt the power supply to
the unit and must be within easy access by the user.
PRECAUTION:
Pour déconnecter complètement ce produit du courant secteur,
débranchez la prise de la prise murale.
La prise secteur est utilisée pour couper complètement
l’alimentation de l’appareil et l’utilisateur doit pouvoir y accéder
facilement.
FRANCAIS ENGLISH
FCC INFORMATION (For US customers)
nNOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION
1. PRODUCT
This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
product may not cause harmful interference, and (2) this product must accept any interference received, including
interference that may cause undesired operation.
2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.
Modification not expressly approved by DENON may void your authority, granted by the FCC, to use the product.
3. NOTE
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this product does cause harmful interference to radio or
television reception, which can be determined by turning the product OFF and ON, the user is encouraged to try to
correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the product into an outlet on a circuit different from that to which the receiver is connected.
•Consult the local retailer authorized to distribute this type of product or an experienced radio/TV technician for
help.
• Keep the unit free from moisture, water,
and dust.
• Protéger l’appareil contre l’humidité, l’eau
et la poussière.
• Do not let foreign objects into the unit.
• Ne pas laisser des objets étrangers dans
l’appareil.
• Avoid high temperatures.
Allow for sufficient heat dispersion when
installed in a rack.
• Eviter des températures élevées.
Tenir compte d’une dispersion de chaleur
suffisante lors de l’installation sur une
étagère.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
• Do not let insecticides, benzene, and
thinner come in contact with the unit.
• Unplug the power cord when not using the • Ne pas mettre en contact des insecticides,
du benzène et un diluant avec l’appareil.
unit for long periods of time.
• Débrancher le cordon d’alimentation
lorsque l’appareil n’est pas utilisé pendant
de longues périodes.
• Handle the power cord carefully.
Hold the plug when unplugging the cord.
• Manipuler le cordon d’alimentation avec
précaution.
Tenir la prise lors du débranchement du
cordon.
* (For apparatuses with ventilation holes)
• Do not obstruct the ventilation holes.
• Ne pas obstruer les trous d’aération.
• Never disassemble or modify the unit in
any way.
• Ne jamais démonter ou modifier l’appareil
d’une manière ou d’une autre.
II
ENGLISH
n Contents
Getting Started
Flow of operations through playback··········································2
Accessories···················································································2
Cautions on Handling····································································3
Cautions on Installation································································3
About the Remote Control Unit···················································3
Inserting the Batteries···································································3
Operating Range of the Remote Control Unit·······························3
Part Names and Functions····························································4
Front Panel·····················································································4
Display···························································································5
Rear Panel······················································································6
Remote Control Unit······································································7
Connections
Important Information···································································8
Cables Used for Connections························································8
Converting Input video signals for Output (Video Conversion
Function)························································································9
How the on-screen display is displayed depending on the video
input signal····················································································9
Installing/Setting the Speakers·················································· 10
Connecting the Speakers···························································· 11
Connecting Devices····································································· 12
Connecting Devices not Equipped with HDMI terminals········· 13
Once Connections are Completed·············································· 17
Turning the Power On·································································· 17
Turning the Power Off·································································· 17
Settings
Menu map····················································································· 18
Examples of On-screen Display and Front Display··················· 19
Making the Optimum Settings for the Connected Speakers
Automatically (Audyssey Auto Setup)·······································20
Making detailed settings (Manual Setup)·································25
Making the input settings (Input Setup)···································32
Playback
Playing Components····································································38
Playing Blu-ray Disc / DVD Players···············································38
iPod® Playback············································································38
Listening to FM/AM Broadcasts··················································39
Listening to SIRIUS Satellite Radio Programs·····························40
Operations During Playback·························································42
Selecting the Surround Mode·····················································42
q Playing sources according to the sources’ audio signal format/
number of channels (Standard Playback)·····································42
w Playing in a DENON original surround mode···························43
e Direct Playback········································································43
r Stereo Playback·······································································44
t Playing the Pure Direct mode·················································44
Adjusting the Sound Field Effects (Parameter)·························44
Adjusting the sound field effects (Surround Parameter)··············44
Adjusting the tone (Tone Control)················································46
Making the MultEQ, Dynamic EQ and Dynamic Volume settings
(Audyssey Settings)·····································································46
Adjust tonal quality for each speaker using graphic equalizer
(Manual EQ)·················································································47
Restoring compressed audio to nearly pre-compressed conditions
for playback (RESTORER)····························································48
Adjusting the audio delay time while watching the picture (Audio
Delay)···························································································48
Checking the Status (Information)······························48
Convenient functions
HDMI Control Function································································49
Setting the power to standby after a certain amount of time
(Sleep Timer Function)································································49
Adjust the volume of the different speakers·····························50
Saving frequently used settings (Quick Select Function)········50
MAIN ZONE settings···································································50
ZONE2 settings···········································································50
Various memory functions··························································50
Playing 2-Channel Sound in ZONE2 (multizone
function)· ··················································································51
Operating the Connected Devices by Remote
Control Unit
Registering Preset Codes····························································52
Operating Registered Devices····················································52
Assigning buttons that are Not Used to Operate Other Devices
(Punch Through Function)···························································54
Other Information································································55
Troubleshooting···································································61
Restoring all the settings to as they were at the time of
purchase (Resetting the Microprocessor)··································64
Specifications·········································································64
List of preset codes···································End of this manual
ENGLISH
Thank you for purchasing this DENON product. To ensure proper
operation, please read this owner’s manual carefully before using the
product.
After reading them, be sure to keep them for future reference.
Connections
Flow of operations through
playback
Getting Started
Getting Started
Perform the operations leading to playback on the AVR-1910 in
the order shown below.
Accessories
Settings
Connections
Check that the following parts are supplied with the product.
Installing/Setting the Speakers (vpage 10)
Connecting the Speakers (vpage 11)
Connecting Devices (vpage 12)
⇩
Remote Control
Turning the Power On (vpage 17)
Multi-Zone
⇩
qOwner’s manual ...................................................................... 1
wGetting Started ........................................................................ 1
eWarranty (for North America model only) ................................ 1
rService station list ................................................................... 1
tRemote control (RC-1117) ........................................................ 1
yR6/AA batteries ....................................................................... 2
uFM indoor antenna .................................................................. 1
iAM loop antenna ..................................................................... 1
oSetup microphone
Playback
⇩
(DM-A409, Cord length: Approx. 25 ft / 7.6 m)......................... 1
t
u
i
o
Information
Settings
Audyssey Auto Setup (vpage 20)
Troubleshooting
Manual Setup (vpage 25)
b Perform “Manual Setup” as necessary.
Input Setup (vpage 32)
Specifications
Playback
Playing Components (vpage 38)
⇩
Selecting the Surround Mode (vpage 42)
⇩
Adjusting the Sound Field Effects (vpage 44)
2
ENGLISH
Getting Started
Cautions on Handling
•Before turning the power switch on
Check once again that all connections are correct and that there are
no problems with the connection cables.
Note:
For proper heat dispersal, do not install this unit in a confined
space, such as a bookcase or similar enclosure.
Connections
•Power is supplied to some of the circuitry even when the unit is
set to the standby mode. When traveling or leaving home for long
periods of time, be sure to unplug the power cord from the power
outlet.
bNote
b
Settings
Playback
•About condensation
If there is a major difference in temperature between the inside of
the unit and the surroundings, condensation (dew) may form on
the operating parts inside the unit, causing the unit not to operate
properly.
If this happens, let the unit sit for an hour or two with the power
turned off and wait until there is little difference in temperature
before using the unit.
Multi-Zone
•Cautions on using mobile phones
Using a mobile phone near this unit may result in noise. If so, move
the mobile phone away from this unit when it is in use.
Remote Control
•Moving the unit
Turn off the power and unplug the power cord from the power
outlet.
Next, disconnect the connection cables to other system units before
moving the unit.
•Note that the illustrations in these instructions may differ from the
actual unit for explanation purposes.
NOTE
Cautions on Installation
b
b
Wall
About the Remote Control Unit
In addition to the AVR-1910, the included remote control unit (RC1117) can also be used to operate the equipment listed below.
qDENON system components
wNon-DENON system components
•By setting the preset memory (vpage 52)
•Replace the batteries with new ones if the set does not operate even
when the remote control unit is operated close to the unit.
•The supplied batteries are only for verifying operation.
•When inserting the batteries, be sure to do so in the proper direction,
following the “q” and “w” marks in the battery compartment.
•To prevent damage or leakage of battery fluid:
•Do not use a new battery together with an old one.
•Do not use two different types of batteries.
•Do not attempt to charge dry batteries.
•Do not short-circuit, disassemble, heat or dispose of batteries in
flames.
•If the battery fluid should leak, carefully wipe the fluid off the inside
of the battery compartment and insert new batteries.
•Remove the batteries from the remote control unit if it will not be in
use for long periods.
•Used batteries should be disposed of in accordance with the local
regulations regarding battery disposal.
Operating Range of the Remote Control
Unit
Point the remote control unit at the remote sensor when operating it.
Information
Inserting the Batteries
30°
qLift the clasp and remove the wLoad the two batteries properly
Troubleshooting
rear cover.
30°
as indicated by the marks in
the battery compartment.
R6/AA
Approx. 23 feet / 7 m
Specifications
NOTE
The set may function improperly or the remote control unit may not
operate if the remote control sensor is exposed to direct sunlight,
strong artificial light from an inverter type fluorescent lamp or infrared
light.
ePut the rear cover back on.
ENGLISH
Getting Started
Part Names and Functions
Front Panel
W6
W5
W4
W3
Button that function in the same way as remote control buttons
W2 W1
o
i
For buttons not explained here, see the page indicated in parentheses ( ).
qPower operation button
(ON/STANDBY)··········································· (17)
Q3 Q4
Q5 W9 E0
Front
w
Q6 Q7
e
r t
Q8
y
u
Q9
q q
W0
u u
Buttons, terminals and displays only provided on the main unit
W2HD AUDIO indicator····································· (43)
o,Q0o,Q0
W3MASTER VOLUME indicator
W4Display
W5Remote control sensor·································· (3)
W6TUNING PRESET button····························· (41)
W7SOURCE MODE SELECT button················ (38)
W8FRONT SPEAKERS SELECT button············ (42)
W9DIMMER button··········································· (31)
E0STATUS button············································ (48)
i i
Troubleshooting
indicator······················································· (47)
o,Q0o,Q0
Q1 Q1
Information
Q6Power indicator··········································· (17)
Q7Power switch (hON jOFF)················· (17, 64)
Q8Headphones jack (PHONES)······················· (42)
Q9V. AUX INPUT connectors·························· (16)
W0SETUP MIC jack··········································· (21)
W1AUDYSSEY DYNAMIC VOLUME
Remote Control
q
Rear
Multi-Zone
n Buttons that function in the same way as Front Panel buttons
Playback
Q2
Settings
Q0 Q1 W8
wSURROUND MODE buttons······················· (42)
eMENU button··············································· (18)
rCursor buttons (uio p)·························· (18)
tENTER button·············································· (18)
yRETURN button··········································· (18)
uQUICK SELECT buttons······························ (50)
iMASTER VOLUME control knob················ (38)
oSOURCE SELECT knob······························· (38)
Q0ZONE2 SELECT button···························· (51)
Q1ZONE2 ON/OFF button···························· (51)
Q2RESTORER button······································· (48)
Q3DYNAMIC EQ button··································· (47)
Q4DYNAMIC VOLUME button························ (47)
Q5MULTEQ button·········································· (46)
Connections
W7
Q2 Q2
w w
e e
Q5 Q5
r r
t t
,
o Q0o,Q0
Specifications
Q3 Q3
Q4 Q4
y y
Q0 Q0
ENGLISH
Getting Started
Part Names and Functions
Display
Q5
Q4
Q3
Q2 Q1
Q0
o i
u
Connections
Settings
q
w
Playback
q Decoder indicators
The indicator for the currently operating decoder
lights.
Multi-Zone
w Input audio signal indicators
e Information display
Remote Control
The input source name, surround mode, setting
values and other information are displayed
here.
e
r
t QUICK SELECT indicators
Information
These light when the Quick Select function is
set (vpage 50).
y ZONE2 indicator
Lights when signals are being output to the
ZONE2 (vpage 51).
Troubleshooting
u Master volume indicator
When performing setting operations, displays
the menu number.
i SLEEP TIMER indicator
Lights when the sleep timer is operating
(vpage 49).
Specifications
o MUTE indicator
Lights when the muting mode is set (vpage
42).
y
Q0 AUDYSSEY indicator
These light as shown below in the different
modes (vpage 46).
: During “MultEQ” operation
:D
uring “MultEQ” , “Dynamic EQ”
operation
r Front speaker indicator
These light according to the settings of the
front A and B speakers (vpage 42).
t
: During “MultEQ” , “Dynamic EQ”,
b
When speaker settings are changed after the
“Dynamic Volume” operation
Audyssey Auto Setup procedure, either the
indicators’ frame turns off or all the indicators
turn off.
Q1 Input mode indicators
Q2 S.BACK indicator
Lights when audio signals are being output from
the surround back speakers (vpage 26).
Q3 RESTORER indicator
Lights during “RESTORER” operation (vpage
48).
Q4 HDMI indicator
Lights when HDMI input signals are detected
(vpage 13).
Q5 Tuner reception mode indicators
This lights according to the reception conditions
when the input source is set to “TUNER”.
•AUTO
This lights when in the auto tuning mode.
•STEREO
In the FM mode, this lights when receiving
analog stereo broadcasts.
•TUNED
This lights when the broadcast is properly
tuned in.
ENGLISH
Rear Panel
Q3
Q2
Q1
Q0
Connections
Q6 Q5 Q4
Getting Started
Part Names and Functions
Settings
Playback
Multi-Zone
Remote Control
Information
w
e
qHDMI connectors········································ (13)
wDigital audio connectors···························· (14)
rPRE OUT connector···································· (11)
t
y
u
i
yREMOTE CONTROL jacks
Connect a device that supports the remote
control function.
"69
065
Input
ZONE2
o
uAnalog audio connectors··························· (14)
Q3ZONE2 connectors·····································(51)
iFM/AM antenna terminals························· (17)
Q4COMPONENT VIDEO connectors·············· (14)
Q5Control Dock for iPod S-Video input terminal
oSpeaker terminals······································· (11)
Q0Power cord·················································· (17)
Q1AC OUTLET················································· (17)
tSIRIUS connector······································· (16)
Infrared
retransmitter
Infrared
sensor
····································································· (14)
Q6Control Dock for iPod DOCK CONTROL jack
····································································· (14)
Q2EXT. IN connectors····································· (16)
Extension jack for future use.
(Connect devices corresponding
with room to room function to
this jack.)
Specifications
eVIDEO connectors······································ (15)
r
Troubleshooting
q
ENGLISH
Getting Started
Part Names and Functions
Remote Control Unit
Front
Rear
Connections
q
w
e
Q6
r
W0
Settings
t
Playback
t
Multi-Zone
W1
W2
W3
W4
y
Remote Control
Q1
W5
Q7
Q2
Information
u
Q3
W7
Q8
i
o
Troubleshooting
t
Q0
W6
Q4
Q5
Q9
W8
q Remote control signal transmitter
w Indicator······················································ (52)
e Power buttons············································ (17)
r QUICK SELECT buttons····························· (50)
t SOURCE SELECT button··························· (38)
y System buttons·········································· (52)
u MENU button············································· (18)
i Cursor buttons (uio p)························· (18)
o SEARCH button·········································· (39)
Q0 DEVICE SELECT switches···················· (38, 52)
Q1 Master volume control buttons················ (38)
Q2 MUTING button·········································· (42)
Q3 Channel level adjustment button············· (50)
Q4 RETURN button·········································· (18)
Q5 ENTER button············································· (18)
Q6 ZONE2 power button································· (51)
Q7 Tuner operation buttons··························· (40)
Q8 MULTEQ button········································· (46)
Q9 Number buttons (0 ~ 9, +10)······················ (52)
W0 MAIN ZONE power buttons······················ (17)
W1 INPUT MODE button·································· (34)
W2 SLEEP TIMER button·································· (49)
W3 VIDEO SELECT button······························· (34)
W4 RESTORER button······································ (48)
W5 FRONT HEIGHT SPEAKER ON/OFF button
····································································· (46)
W6 Surround mode buttons···························· (42)
W7 DYNAMIC VOLUME button······················· (47)
W8 DYNAMIC EQ button································· (47)
Specifications
For buttons not explained here, see the page
indicated in parentheses ( ).
NOTE
Buttons on the back panel may operate when the
back lid is pressed.
Operations
control
possible
by
remote
n Operations on the AVR-1910
n Operations on six devices other that
the AVR-1910
•Preset the remote control codes of the
devices to be operated (vpage 52).
•Switch two device selector switches according
to the devices to be operated.
Position of switches
Operable devices
AVR-1910
(MAIN ZONE)
iPod
AVR-1910 (ZONE2)
TV
Blu-ray disc player
or
DVD Player
DVD recorder
or
Video deck
Satellite receiver
or
Cable TV
CD player
n ZONE2 operations (vpage 51)
n Punch through setting (vpage 54)
ENGLISH
n Connection Flow
Connections for all compatible audio and video signal formats
are described in this owner’s manual. Please select the types of
connections suited for the equipment you are connecting.
After connections are completed, certain settings must be made on
the receiver. Make the settings indicated“ Set as necessary ”
for the individual items.
NOTE
n Recording Components
n SAT/CABLE Tuner (vpage 15)
n Other Devices
• Video Camera / Game Console (vpage 16)
n Power Cord
Analog
connections
Optical cable
(White)
L
L
(Red)
R
R
Stereo pin-plug cable
Analog
connections
(monaural, for
subwoofer)
Pin-plug cable
Speaker
connections
Speaker cables
Video cables
Component
video
connections
(Green)
(Blue)
(Red)
Specifications
• Component with Multi-channel Output connectors
(vpage 16)
• SIRIUS Connector (vpage 16)
• Antenna terminals (vpage 17)
Coaxial digital cable
Optical digital
connections
Troubleshooting
• DVD Recorder (vpage 15)
• Video Cassette Recorder (vpage 15)
Coaxial digital
connections
Information
• Blu-ray Disc player / DVD player (vpage 14)
• iPod® (vpage 14)
• CD Player (vpage 14)
HDMI cable
Audio cables
Remote Control
n HDMI (vpage 12)
n Monitor (TV) (vpage 13)
n Playback Components
Audio and video cables
HDMI
connections
Multi-Zone
Connecting Devices not Equipped with HDMI
terminals (vpage 13)
Select the cables according to the equipment being connected.
Playback
Connecting Devices (vpage 12)
• Do not plug in the power cord until all connections have been
completed.
• When making connections, also refer to the operating instructions
of the other components.
• Be sure to connect the left and right channels properly (left with left,
right with right).
• Do not bundle power cords together with connection cables. Doing
so can result in humming or noise.
Cables Used for Connections
Settings
Connecting the Speakers (vpage 11)
Important Information
Connections
Installing/Setting the Speakers (vpage 10)
Getting Started
Connections
Component video cable
S-Video
connections
S-Video cable
Video
connections
(Yellow)
75 Ω/ohms pin-plug video cable
Turning the Power On (vpage 17)
8
ENGLISH
Getting Started
Important Information
Converting Input video signals for Output
(Video Conversion Function)
How the on-screen display is displayed depending on the
video input signal
Connections
Settings
The AVR-1910 is equipped with four types of video input terminals (HDMI, Component video, S-Video and
video) and three types of video output terminals (HDMI, Component video and video).
Use the terminals according to the devices to be connected.
This function automatically converts various formats of video signals input to the AVR-1910 into the format
used to output the video signals from the AVR-1910 to a monitor.
AVR-1910
Monitor (TV)
Video devices
Playback
Multi-Zone
Output
Input
(IN)
Remote Control
HDMI connector
HDMI connector
Component video
connectors
Component video
connectors
Output
(MONITOR OUT)
HDMI
connector
Component video
connectors
The way the on-screen display of the menus, status, etc., is displayed differs according to the type of video
signal input to the AVR-1910.
When video signals are input from the HDMI or component video terminals
• Menu: Switches to a screen with a black background and the menu is superimposed. (b1)
• Status display: Not displayed.
b1: If you want to display the menus superimposed on the picture being played, input the same video
signals to the S-Video or video terminals. When a menu is displayed, the picture switches to the one
being input from the S-Video or video terminals and the menu is displayed superimposed over this
picture.
Input
NOTE
Menus and status display screens are not displayed for component video terminal pictures. To
display them, also connect the video terminals.
HDMI connector
Component video
connectors
When video signals are being input from the S-Video or video terminals
• Menu: Menus are displayed superimposed over the picture being played.
• Status display: Displayed.
n Examples of on-screen display
Information
S-Video connector
S-Video
connector
Video connector
Video connector
• Menu screen
Video connector
Video connector
Troubleshooting
Specifications
•The video conversion function supports the NTSC, PAL, SECAM, NTSC 4.43, PAL-N, PAL-M and PAL-60
formats.
•The resolution of the video signal input to the AVR-1910’s HDMI terminal is the resolution set at
“Resolution” (vpage 34). (1080p HDMI signals and 1080p component signals are output at 1080p,
regardless of the setting.)
•Resolutions of HDMI-compatible TVs can be checked at “HDMI Monitor Information” (vpage 48).
NOTE
•The S-Video input terminal is exclusively for use with a Control Dock for iPod. It can be used when the
Control Dock for iPod is connected to the terminal assigned to the iPod input source.
•HDMI signals cannot be converted into analog signals.
•When a non-standard video signal from a game machine or some other source is input, the video
conversion function might not operate.
• Status display screen
When the input source is
switched
When the volume is adjusted
MENU
1.Parameter
2.Information
3.Auto Setup
4.Manual Setup
5.Input Setup
[ENT]:Select
[Auto]
IN :DVD
MODE:STEREO
Master Volume -80.0dB
Status display: The operating status is displayed temporarily on the
screen when the input source is switched or the
volume is adjusted.
ENGLISH
n When 7.1ch (Surround Back Speaker) Connected
Front speakers
2
z1
z4
z5
Surround speakers
Front
speaker
It is not possible to use the front height speakers and
surround back speakers simultaneously.
Surround speakers
Surround back
speaker
GAs seen from aboveH
GAs seen from the sideH
4
Subwoofer
Surround
Surround back
speaker
speaker
Front
speaker
2 to 3 feet /
60 to 90 cm Point slightly
downwards
z2
z1
Monitor
z
3
z1:30˚
z2:45˚
z3:90˚
z4:110˚
Point slightly
downwards
Front height
speaker
Front speaker
Surround
speaker
2 to 3 feet /
60 to 90 cm
Surround speakers
GAs seen from aboveH
GAs seen from the sideH
Troubleshooting
NOTE
3
2
Center speaker
Information
Surround back speakers
z
z
Front height speakers
Front speakers
z1:22 ~ 30˚
z2:90˚
z3:110˚
z
z1
Surround
speaker
n When 7.1ch (Front Height Speaker) Connected
Remote Control
Subwoofer
GAs seen from the sideH
Multi-Zone
Center
speaker
GAs seen from aboveH
Front speakers
Center speaker
Monitor
2 to 3 feet /
60 to 90 cm
Surround speakers
GAs seen from the sideH
n When 6.1ch Connected
Surround
speaker
Playback
Surround
Surround back
speaker
speaker
Front
speaker
2 to 3 feet /
60 to 90 cm Point slightly
downwards
GAs seen from aboveH
Front
speakers
Surround
speaker
Subwoofer
3
Surround back
speakers
Front Height speakers
Subwoofer
z
z1:22 ~ 30˚
z2:120˚
Settings
aDetermine the Speaker Layout.
z
Front speakers
Center speaker
Monitor
z4:30˚
z5:45˚
z2
z1
Installing All the Speakers
z1:22 ~ 30˚
z2:90˚
z3:110˚
Center speaker
Monitor
Subwoofer
Below we introduce examples of speaker layouts. Refer
to these to arrange your speakers according to their
type and how you want to use them.
n When 5.1ch Connected
Connections
•The AVR-1910 is compatible with various types
of surround playback.
• Decide on the surround modes to be played on
the AVR-1910 before making connections and
settings.
Getting Started
Installing/Setting the Speakers
Specifications
10
ENGLISH
Getting Started
Installing/Setting the Speakers
sSet the “Amp Assign” Mode According to the Speaker Layout.
The signals output from the AVR-1910’s SURR. BACK/AMP ASSIGN speaker terminals can be
switched to signals of the surround mode being used (vpage 25 “Amp Assign”).
Connections
Amp assign mode
(vpage 25)
SURR. BACK/AMP ASSIGN
Speaker connections
Connecting the Speakers
Subwoofer with
builtin amplifier
Front speakers
A
Center
speaker
Surround
speakers
Example of speaker installation
(L)
Settings
w
Normal
Front speakers
B
(R)
q
w
(L)
q
w
q
*/
Surround back
speakers
(L)
(R)
w
w
q
(R)
q
w
qw
q
Playback
(7.1)
Multi-Zone
Normal
Remote Control
Surround back
speakers
bConnect to the “L”
speaker terminal.
bSet “Surround Back”
(vpage 26) to “1spkr”.
(6.1)
Not connected
Normal
Information
bSet the “Surround Back”
setting (vpage 26) to
“OFF”.
(5.1)
Troubleshooting
Front Height
Specifications
Front A Bi-Amp
or
Front B Bi-Amp
For connections of the SURR. BACK/AMP
ASSIGN speaker terminals, see “Amp Assign”
(vpage 25).
Front Height
speakers
Protection circuit
(7.1)
Front A or B
speakers
bFor connections,
see “About bi-amp
connections”
(vpage 12).
(5.1)
ZONE2
(Default)
MAIN ZONE
ZONE2 speakers
(5.1)
11
ZONE2
(2)
If the core wires touch the rear panel and the screws
etc., or the ± sides touch each other, the protection
circuit will be activated and the power indicator will
flash red at intervals of 0.5 secs.
If the protection circuit is activated, the speaker
output is isolated, and the power supply goes to
the standby state. If the power supply is turned off,
after the power supply cord is withdrawn, please
confirm that speaker cable and input cable are
connected.
Also, if replaying large sound levels by using
a speaker having an impedance less than that
specified (eg, 4 Ω/ohms), the temperature will rise,
and the protection circuit might be activated. The
power supply will go into the standby state, and the
power indicator will flash red at 2 second intervals.
In this case, please switch off the power supply,
and wait until the AVR-1910 has cooled down, and
the surrounding ventilation is good.
Even if there are no problems with the surrounding
ventilation and connections, in the event of the
protection circuit becoming activated,
due to thinking that the AVR-1910 has failed, please
contact DENON Service center after switching off.
ENGLISH
About bi-amp connections
Carefully check the left (L) and right (R) channels and + (red) and –
(black) polarities on the speakers being connected to the AVR-1910,
and be sure to interconnect the channels and polarities correctly.
These connections make for higher quality playback sound with no
interference between the signals of the bass and treble units.
When the amplifier assignment mode is set to “Front A Bi-Amp” or
“Front B Bi-Amp”, connect as shown below. (The illustration shows a
connection example for the front B Bi-Amp speakers.)
1
Peel off about 10 mm of sheathing from the tip
of the speaker cable, then either twist the core
wire tightly or terminate it.
q
w
(L)
q
w
(R)
AVR-1910
n Functions usable with HDMI connections
Deep Color
Eliminates on-screen color banding, for smooth tonal transitions and
subtle gradations between colors.
x.v.Color
Tighten the speaker terminal firmly before
inserting the banana plug.
Enables displays with natural, vivid colors. “x.v.Color” is a Sony
registered trademark.
Auto Lip Sync (vpage 28)
NOTE
NOTE
This function allows you to operate external devices from the receiver
and operate the receiver from external devices.
NOTE
These functions will not work if the device connected to the HDMI
terminal does not support Deep Color or x.v.Color signal transfer or
the Auto Lip Sync function.
n Copyright protection system (HDCP)
The AVR-1910 supports HDCP (High-bandwidth Digital Contents
Protection). HDCP is a copyright protection technology for digital video
signals. The devices connected to the AVR-1910 must also support
HDCP.
NOTE
When a device that does not support HDCP is connected, video
signals are not properly output.
12
Specifications
•Use speakers compatible with bi-amp connections.
•When making bi-amp connections, be sure to remove the shortcircuiting plate or wire between the speaker’s woofer and tweeter
terminals.
HDMI control function (vpage 28, 49)
Troubleshooting
•Connect the speaker cables in such a way that they do not stick out
of the speaker terminals. The protection circuit may be activated if
the core wires touch the rear panel or if the + and – sides touch each
other (v “Protection circuit”).
•Never touch the speaker terminals while the power
supply is connected. Doing so could result in electric shock.
When in the “Front A Bi-Amp” and “Front B Bi-Amp” modes, the
same signals are output from the front speaker terminals and the AMP
ASSIGN terminals.
Information
HDMI 1.3 incorporates an automatic video/audio synching capability
that allows devices to perform this synchronization automatically with
total accuracy.
Use speakers with an impedance of 6 to 16 Ω/ohms. When using front
A and B speakers simultaneously, use speakers with an impedance of
12 to 16 Ω/ohms.
Remote Control
n When using a banana plug
“HDMI”, “HDMI logo” and “High-Definition Multimedia Interface”
are trademarks or registered trademarks of HDMI Licensing LLC.
Multi-Zone
Turn the speaker terminal clockwise to tighten
it.
“HDMI” is the abbreviation of “High Definition Multimedia
Interface”. This interface allows transfer of digital video signals
and digital audio signals over a single HDMI cable.
Playback
Insert the speaker cable’s core wire to the hilt
into the speaker terminal.
Important Information
Settings
Turn the speaker terminal counterclockwise
to loosen it.
Connecting Devices Equipped with
HDMI terminals
n About HDMI
Front speakers B
2
3
4
Connecting Devices
Connections
Connecting the Speaker Cables
Getting Started
Connecting the Speakers
ENGLISH
Getting Started
Connecting devices
Connections
The AVR-1910 allows connection of inputs from up to 4 HDMI
devices and output to 1 TV.
Connections
DVD
Player
)%.*
065
Settings
Playback
Multi-Zone
Blu-ray
Disc Player
)%.*
065
SAT/CABLE
Tuner
)%.*
065
Digital Video
Recorder
)%.*
065
nConnecting to a device equipped with a DVI-D
terminal
When an HDMI/DVI conversion cable (sold separately) is used, the
HDMI video signals are converted to DVI signals, allowing connection
to a device equipped with a DVI-D terminal.
NOTE
•No sound is output when connected to a device equipped with a
DVI-D terminal. Also make the audio connections.
•Signals cannot be output to DVI-D devices that do not support
HDCP.
•Depending on the combination of devices, the video signals may not
be output.
nSettings related to HDMI connections
Connecting Devices not
Equipped with HDMI terminals
Monitor (TV)
•Select the terminal to use and connect the device.
•For video connections, see “Converting input video signals for output
(Video Conversion Function)” (vpage 9).
For instructions on HDMI connections, see “Connecting Devices
Equipped with HDMI terminals” on page 12.
Monitor (TV)
"6%*0
015*$"065
7*%&0
7*%&0
*/
$0.10/&/57*%&0
*/
:
1# 13
Set as necessary. For details, see the respective reference pages.
Input terminal assignment (vpage 33)
Set this when changing the input sources of the different terminals.
Remote Control
Monitor
(TV)
)%.*
*/
Information
Troubleshooting
•Use a cable on which the HDMI logo is indicated (a certified HDMI
product) for connection to the HDMI connector. Normal playback
may not be possible when using a cable other than one on which the
HDMI logo is indicated (a non-HDMI-certified product).
•When the AVR-1910 is connected to other devices with HDMI cables,
also connect the AVR-1910 and TV using an HDMI cable.
•When a device supporting Deep Color signal transfer is connected,
use a cable compatible with HDMI ver.1.3a.
•Video signals are not output if the input video signals do not match
the monitor’s resolution. In this case, switch the Blu-ray Disc player /
DVD player’s resolution to a resolution with which the monitor is
compatible.
HDMI Setup (vpage 28)
Make these settings related to HDMI input/output signals.
•Auto Lip Sync
•HDMI Audio Out
•HDMI Control
•Standby Source
•Power Off Control
NOTE
The audio signals output from the HDMI connectors are only the
HDMI input signals.
Specifications
NOTE
•If the menu “HDMI Audio Out” setting (vpage 28) is set to “AMP”,
the sound may be interrupted when the monitor’s power is turned
off.
•The audio signal from the HDMI output terminal (sampling
frequency, number of channels, etc.) may be limited by the HDMI
audio specifications of the connected device regarding permissible
inputs.
13
The component video connectors may be indicated differently on your
monitor. For details, see the monitor’s operating instructions.
ENGLISH
CD Player
Control dock for iPod®
Playback Components
Use a DENON control dock for iPod (ASD-1R, ASD-11R, ASD-3N or
ASD-3W sold separately) to connect the iPod to the AVR-1910. For
instructions on the control dock for iPod settings, refer to the control
dock for iPod’s operating instructions.
Blu-ray Disc player / DVD player
For instructions on HDMI connections, see “Connecting Devices
Equipped with HDMI terminals” on page 12.
Control dock for iPod
Blu-ray Disc player /
DVD player
L
R
L
R
ASD-3N
ASD-3Nor
または
ASD-3W
ASD-3W
Settings
7*%&0
"6%*0
$0"9*"065
"6%*0
065
3
R
L
R
R
L
R
L
Multi-Zone
L
Playback
$0.10/&/57*%&0
065
:
1# 13
"6%*0
"6%*0
065
3
Connections
Select the terminal to use and connect the device.
CD Player
Getting Started
Connecting Devices not Equipped with HDMI terminals
Remote Control
Set as necessary
Information
Set this to change the input signal to which the input source
is assigned.
“Assign” (vpage 33)
Troubleshooting
Specifications
Set as necessary
Set as necessary
Set this to change the input signal to which the input source
is assigned.
“Assign” (vpage 33)
NOTE
When connected to a Blu-ray Disc player, and playing Dolby TrueHD,
DTS-HD, Dolby Digital Plus, connect the HDMI.
Set this to assign the iPod to a terminal other than “VCR (iPod)”
“iPod Dock” (vpage 33)
With the default settings, the iPod can be used connected to the VCR
(iPod) connector.
14
ENGLISH
Getting Started
Connecting Devices not Equipped with HDMI terminals
Recording Components
SAT/CABLE Tuner
Select the terminal to use and connect the device.
Connections
Digital Video Recorder
Video Cassette Recorder
Select the terminal to use and connect the device.
Select the terminal to use and connect the device.
For instructions on HDMI connections, see “Connecting Devices
Equipped with HDMI terminals” on page 12.
For instructions on HDMI connections, see “Connecting
Devices Equipped with HDMI terminals” on page 12.
Settings
DVD Recorder
Video cassette recorder
7*%&0
Playback
$0.10/&/57*%&0
065
:
1# 13
"6%*0
7*%&0
065
015*$"065
7*%&0
"6%*0
065
3
Multi-Zone
L
L
R
R
7*%&0
*/
"6%*0
"6%*0
*/
3
L
L
015*$"*/
R
"6%*0
7*%&0
"6%*0
"6%*0
*/
3
7*%&0
065
"6%*0
065
3
L
R
L
R
R
L
L
For instructions on HDMI connections, see “Connecting
Devices Equipped with HDMI terminals” on page 12.
SAT/CABLE Tuner
"6%*0
"6%*0
065
3
L
R
L
R
$0"9*"065
7*%&0
7*%&0
065
R
R
Remote Control
Information
Troubleshooting
Set as necessary
Specifications
Set as necessary
Set this to change the input signal to which the input source is
assigned.
“Assign” (vpage 33)
NOTE
•To record video signals through the AVR-1910, use the same type of video
cable for connection between the AVR-1910 and the player as the cable
used for connection between the AVR-1910 and the recorder.
•Do not connect the output of the component connected to the AVR-1910’s
OPTICAL2 output connector to any input connector other than OPTICAL2.
15
Set as necessary
Set this to change the input signal to which the input source
is assigned.
“Assign” (vpage 33)
NOTE
To record video signals through the AVR-1910, use the same type
of video cable for connection between the AVR-1910 and the
player as the cable used for connection between the AVR-1910
and the recorder.
Set this to change the input signal to which the input source
is assigned.
“Assign” (vpage 33)
ENGLISH
SIRIUS Connector
Other Devices
Video camera /
Game console
7*%&0
7*%&0
065
Settings
"6%*0
"6%*0
065
3
-
SIRIUSConnect Home Tuner
L
R
L
Playback
R
Multi-Zone
bWhen connecting
digital audio
Remote Control
Component with Multi-channel Output connectors
The video signal can be connected in the same way as a Blu-ray Disc player / DVD player (vpage 14).
Set as necessary
"6%*0
46#
800'&3
'30/5
-
R
463306/%
-
L
3
R
463306/%
#"$,
-
L
3
R
To play analog signals input from the
external input (EXT. IN) terminal, set
“Input Mode” (vpage 34) on the menu
to “EXT. IN”.
“EXT. IN” can also be selected with
.
NOTE
Keep the power cord unplugged until the SiriusConnect Home Tuner connection have been completed.
“SIRIUS, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. and its subsidiaries.
All rights reserved. Service not available in Alaska and Hawaii.”
nPositioning the Antenna
For a consistent satellite signal, the antenna must be positioned correctly. Use the following map to
determine which area you are in and position the antenna accordingly.
L
R
L
R
L
R
NORTH
WEST
q
t
w
r
e
SOUTH
16
Specifications
Area 1 :Point the antenna toward the sky in the east,
northeast, or southeast, either through a
window or outside.
Area 2 :Point the antenna toward the sky in the north
or northeast, either through a window or
outside.
Area 3 :Point the antenna toward the sky in the north
or northwest, either through a window or
EAST
outside.
Area 4 :Point the antenna toward the sky in the west,
northwest, or southwest, either through a
HORIZON
window or outside.
Area 5 :Put the antenna outside and point it straight
up. The antenna cannot be used indoors.
SKY
Troubleshooting
L
3
$&/5&3
When connecting digital of the SiriusConnect Home
Tuner, perform the setting “Assign” (vpage 33) from
the menu.
Information
Blu-ray Disc player / DVD player /
External decoder
Connections
•The AVR-1910 is a SIRIUS Satellite Radio Ready® receiver. You can receive SIRIUS® Satellite Radio by
connecting to the SiriusConnect Home Tuner and subscribing to the SIRIUS service.
•Plug the SIRIUS connector on the rear panel.
•Position the Home Tuner antenna near a south-facing window to receive the best signal.
For details, see “Listening to SIRIUS Satellite Radio Programs” (vpage 40, 41).
When making connections, also refer to the operating instructions of the SiriusConnect Home Tuner.
Video Camera / Game Console
Getting Started
Connecting Devices not Equipped with HDMI terminals
ENGLISH
Getting Started
Connecting Devices not Equipped with HDMI terminals
Antenna terminals
3
Direction of broadcasting station
Connections
FM antenna
Return the lever.
Turning the Power On
NOTE
75 Ω/ohms
Coaxial cable
Settings
AM loop
antenna
(supplied)
FM indoor antenna
(supplied)
Once Connections are
Completed
•Do not connect two FM antennas simultaneously.
•Even if an external AM antenna is used, do not disconnect the AM
loop antenna.
•Make sure the AM loop antenna lead terminals do not touch metal
parts of the panel.
1
Press
.
The power indicator lights red and the
power is set to the standby mode.
2
Press
.
The power indicator flashes green and the
power turns on.
Playback
bAlso press
Connecting the Power Cord
Multi-Zone
Wait until all connections have been completed before connecting the
power cord.
AM outdoor antenna
Ground
nAM loop antenna assembly
Remote Control
1
connection line.
To household
power outlet
(AC 120 V, 60 Hz)
Information
2
3-1
Bend in the reverse direction.
Connection to the AC outlets
Troubleshooting
Specifications
•These outlets supply power to external audio equipment.
•Audio equipment with a total power consumption of 120 W (1 A) can be connected.
•The power supply turns on and off together
with the
on the main unit. When set
to “ON”, power is supplied from the outlet.
When set to “STANDBY”, no power is supplied.
With the antenna on top of any
stable surface.
Mount
the antenna attached to a
3-2With
wall.
NOTE
Installation hole Mount on wall, etc.
When “HDMI Control” (vpage 28) is set
to “ON”, power is supplied constantly to
the AC outlet (UNSWITCHED).
nConnection of AM antennas
Push the lever.
Insert the conductor.
17
when in standby
mode, the power turns on.
When
has been pressed, the input source set with the
is set. If a
has been pressed, the input source
stored in the memory for the quick select function is set (vpage
50 “Saving frequently used settings (Quick Select Function)”).
Power cord
Remove the vinyl tie and take out the
1
2
Front
NOTE
•Insert the AC plugs securely. Incomplete connections could cause
noise.
•Only use the AC outlets to plug in audio equipment. Do not use
them as power supplies for hairdryers or anything other than audio
equipment.
This operation can also be performed by pressing a
the main unit.
on
Turning the Power Off
1
Press
.
Front
The power is set to the standby mode.
2
Press
.
The power indicator turns off, and so does
the power.
NOTE
•Power continues to be supplied to some of the circuitry even when
the power is in the standby mode. When leaving home for long
periods of time or when traveling, either press
to turn off the
power, or unplug the power cord from the power outlet.
•When the ZONE2 power is switched on, and you want to switch off
the MAIN ZONE power, press
.
ENGLISH
Getting Started
Settings
With the AVR-1910, settings and operations for most functions can be performed by operating while looking at the menus displayed on the monitor screen.
.
MENU
⇩
Setting items
Number
Description
Page
1-1
1-2
1-3
1-4
1-5
1-6
2-1
2-2
2-3
Surround Parameter
Tone Control
Audyssey Settings
Manual EQ
RESTORER
Audio Delay
Status
Audio Input Signal
HDMI Information
Adjust surround sound parameters.
Adjusts the treble and bass tone.
Makes the MultEQ, Dynamic EQ and Dynamic Volume settings.
Adjust tonal quality for each speaker using graphic equalizer.
Uncompress compressed sources and apply bass boost for richer sound.
Compensate for incorrect timing between video and audio.
Shows information about current settings.
Shows information about audio input signals.
Displays the HDMI input/output signals and TV information.
44
46
46
47
48
48
48
48
48
2-4
2-5
2-6
3-1
Auto Surround Mode
Quick Select
Preset Channel
Audyssey Auto Setup
48
48
48
21
3-2
Parameter Check
4-1
4-2
4-3
4-4
4-5
5-1
5-2
5-3
5-4
5-5
5-6
5-1
5-2
5-3
5-2
5-3
Speaker Setup
HDMI Setup
Audio Setup
ZONE2 Setup
Option Setup
Assign
Video
Input Mode
Rename
Source Level
iPod Playback Mode
Auto Preset
Preset Skip
Preset Name
Parental Lock
Antenna Aiming
Displays the settings stored for the auto surround mode.
Displays the settings stored for the Quick Select function.
Shows information about preset channels.
Makes the optimum settings for the speakers being used
automatically.
Check Audyssey Auto Setup measurement results.
This item is only displayed after the Audyssey Auto Setup procedure
has been performed.
Sets the speaker size and distance, the channel level, etc.
Make settings for HDMI video/audio output.
Make settings for audio playback.
Make settings for audio playback in a ZONE2 system.
Make various other settings.
Change input connector assignment.
Makes the video settings.
Sets the audio input mode and decode mode.
Change the display name for this source.
Adjust the playback level of the audio input.
Make settings for iPod playback.
Use the auto preset function to program radio stations.
Set the preset memories that you do not want to display when tuning.
Assign name to a preset memory.
Set the channel radio reception limits.
Check the SIRIUS radio reception sensitivity.
2. Information
Show information about receiver
settings, input signals, etc.
4. Manual Setup
Use this to make various types of
detailed settings.
25
28
29
30
30
33
34
34
35
35
35
36
36
36
37
37
Specifications
5. Input Setup
Use this to make settings related
to playing input sources.
24
Troubleshooting
3. Auto Setup
Makes the optimum speaker
settings and corrects for the
acoustic characteristics of the
room.
Detailed items
The settings made up to that
point are entered and the
settings menu screen turns off.
Information
Front
to
Remote Control
Set these for example upon purchase.
Once these items are set, there is no need to
set them again unless the speaker layout or the
connected speakers have been changed.
bSelect “Default Yes”, then press
reset to the default setting.
1. Parameter
Adjust various audio parameters.
[ENT]:Select
Items that only need to be set once
.
.
Multi-Zone
1.Parameter
2.Information
3.Auto Setup
4.Manual Setup
5.Input Setup
.
bTo return to the previous item, press
5Press
Playback
n Setting menus
⇩
you want to
set, then press
se uiop to select the item,
4Uthen
press
to set.
Settings
you want to
set, then press
ress ui to
3Pselect
the item
⇩
ress ui to
2Pselect
the item
.
The menu is
displayed.
⇩
1Press
n Operations
Connections
Menu map
18
ENGLISH
Getting Started
Examples of On-screen Display and Front Display
Below we describe typical examples of displays on the TV screen and on the set’s display window.
On-screen Display
Connections
n Top menu display
Front Display
Description
MENU
w 1.Parameter q
2.Information
3.Auto Setup
4.Manual Setup
5.Input Setup
Settings
Playback
e
q : The menu items are displayed here.
w : The selected line is displayed here.
q
q : The number of the current selected setting menu is
Parameter
w
e
The currently selected item is displayed on the display.
Use ui to move to the item you want to set.
e : The number of the current selected setting menu is
displayed.
[ENT]:Select
n Display when changing settings
Assign
q 5-1-1.Input
HDMI Digi Comp
Multi-Zone
DVD
HDP
TV
SAT/CBL
VCR/iPod
DVR
e
1
2
C1
w3
01
C2
4
02
1
DVD
[HDMI1 ]
w
2
displayed.
w : Use uio p to move to the item you want to set.
e : Press
to set to the mode in which the setting can be
made.
[ENT]:Select [RTN]:Back
Remote Control
⇩
Press
⇩
.
Press
.
Assign
q 5-1-1.Input
HDMI Digi Comp
Information
DVD
HDP
TV
SAT/CBL
VCR/iPod
DVR
1
2
C1
r3
01
C2
4
02
1
DVD
r : 0 1 is displayed at the sides of items whose setting can be
changed. Use o p to change to the desired setting.
•HDMI1 –
r
2
Troubleshooting
[ENT]:Select [RTN]:Back
n Display when inputting characters
e 5-4.Rename
DVD
q
q : When o p is pressed, the cursor moves to the left or right.
w : When ui is pressed at the position at which you want to
DVD
:
DVD
Specifications
Default
•¡
w
DVD
–
e
q
input the character, the character is input.
e : The number of the current selected setting menu is
displayed.
[SRCH]:Caps.
[ENT]:OK
[RTN]:Cancel
n Display when resetting
w
5-4.Rename
Default
DVD
:[
DVD
]
q
w
q Default
[ ]:Up/Down
[ENT]:Select [RTN]:Back
19
q : Press i to select “Default”, then press
to set.
w : The number of the current selected setting menu is
displayed.
Default? : • No
w
ENGLISH
Getting Started
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)
The acoustic characteristics of the connected speakers and listening room are measured and the optimum settings are made automatically.
Step 1 :Connect the included Setup
Microphone (vpage 21)
n Changing the amplifier assignment (Amp Assign)
(vpage 22)
GExample qH
FHL
FL
SW
C
FR
GExample wH
FHR
FHL
FL
SW
C
FR
FHR
NOTE
Results (Parameter Check) (vpage 24)
SL
SR
SL
SR
GExample qH
FL
SW
C
GExample wH
FR
FL
SW
C
FR
( : Measuring positions)
SL
SR
SL
SR
*M
*M
SBL
SBR
SBL
SBR
20
Specifications
n When using Surround Back Speakers
Troubleshooting
*M
*M
• Loud test sounds may be played during Audyssey MultEQ automatic
speaker setup. This is part of normal operation. If there is background
noise in room, these test signals will increase in volume.
• Do not stand between the speakers and setup microphone or allow
obstacles in the path while the measurements are being made. This
will cause inaccurate readings.
• Make the room as quiet as possible. Background noise can disrupt
the room measurements. Close windows, silence cell phones,
televisions, radios, air conditioners, fluorescent lights, home
appliances, light dimmers, or other devices as measurements may
be affected by these sounds.
Cell phones should be placed away from all audio electronics during
the measurement process as Radio Frequency Interference (RFI)
may cause measurement disruptions (even if the cell phone is not in
use).
Information
( : Measuring positions)
n Check Audyssey Auto Setup Measurement
About the main listening position (*M)
The main listening position refers to the most central position where
one would normally sit within the listening environment.
MultEQ uses the measurements from this position to calculate
speaker distance, level, polarity, and the optimum crossover value
for the subwoofer.
Remote Control
n When using Front Height Speakers
Step 3 : Performing the Audyssey Auto Setup
Procedure (vpage 22)
: Front height speaker (L)
: Front speaker (L)
: Subwoofer
: Center speaker
: Front speaker (R)
: Front height speaker (R)
: Surround speaker (R)
: Surround back speaker (R)
: Surround back speaker (L)
: Surround speaker (L)
Multi-Zone
(Front Sp.) (vpage 21)
FHL
FL
SW
C
FR
FHR
SR
SBR
SBL
SL
Playback
n Setting the speakers for playing the front channel
Audyssey MultEQ® automatically measures the acoustical
problems in the listening environment to create the best audio
experience for your home theater.
• When the Audyssey Auto Setup procedure is performed, the
MultEQ, Dynamic EQ and Dynamic Volume functions (vpage 46)
are enabled.
• Use the included setup microphone (DM-A409) to perform the
Audyssey Auto Setup procedure.
• Measurements are performed by placing the calibrated microphone
successively at multiple positions throughout the listening area as
shown in GExample qH. For best results, it is strongly recommended
to measure 6 positions so that the measurements have the proper
spatial weighting.
Even if the listening environment is small as shown in GExample wH,
measuring at multiple points throughout the listening environment
results in more effective correction.
Settings
Step 2 :Audyssey Auto Setup Preparations
(vpage 21)
Important Information
Connections
n Audyssey Auto Setup Flow
ENGLISH
Getting Started
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)
Step 2 : Audyssey Auto Setup
Preparations
Step 1 : Connect the included Setup Microphone
NOTE
NOTE
Connections
•Do not disconnect the setup microphone until the Audyssey Auto
Setup procedure is completed.
•When using headphones, unplug the headphones before starting
the Audyssey Auto Setup procedure.
Settings
Playback
Multi-Zone
If adjustment to the environment is necessary, set the following
items before proceeding.
When using a subwoofer on which the volume can
be adjusted and the crossover frequency can be set
Setting the speakers for playing the front channel
(Front Sp.)
(vpage 11 “Connecting the Speakers”)
When using a subwoofer, make the following settings before starting
the Audyssey Auto Setup procedure:
The front speaker to be measured can be selected ahead of time
here.
Set the TV’s input to the AVR-1910.
n When using a subwoofer with a direct mode
(vpage 17 “Turning the Power On”)
n When using a subwoofer without a direct mode
1 Press ui to select “Front Sp.”.
2 Use op to select the speakers.
Remote Control
1 Check the speaker connections.
2 Turn on the power of the TV and subwoofer.
3 Turn on the AVR-1910’s power.
Connect the included calibrated setup microphone to
4 the
SETUP MIC jack on the main unit.
around items indicate the settings made upon purchase.
•Do not hold the microphone in your hand during measurements.
•Avoid placing the microphone close to a seat back or wall as sound
reflections may give inaccurate results.
The Audyssey Auto Setup screen appears automatically.
Set the direct mode to “On” and disable the volume adjustment
and crossover frequency setting.
Make the following settings:
•Volume
:“12 o’clock position”
•Crossover frequency :“Maximum/Highest Frequency”
•Low pass filter
:“Off”
•Standby mode
:“Off”
3-1.Audyssey Auto Setup
MultEQ
Please place microphone
at ear height at
main listening position.
Front Sp.: A
Amp Assign:
Normal
Start
Cancel
[ENT]:Select [RTN]:Back
Sound
receptor
Information
Troubleshooting
5
Mount the setup microphone on a tripod or stand and
install it at the main listening position.
When installing the setup microphone, adjust its height so that
the section where the sound is received is at the height of the
ears during listening.
Specifications
21
A
: The sound is output from front speakers A when measuring
the front speakers.
B
: The sound is output from front speakers B when measuring
the front speakers.
A + B : The sound is output simultaneously from front speakers A
and B when measuring the front speakers.
n To cancel Audyssey Auto Setup
Setup
microphone
Front
Use ui to select “Cancel”, then use o p to select “Yes”.
ENGLISH
Changing the amplifier assignment (Amp Assign)
The signals output from the AVR-1910’s SURR. BACK/AMP ASSIGN
speaker terminals can be switched to signals of the surround mode
being used.
Front
Detection of the speaker
configuration starts.
from the speakers connected to the SURR.
BACK/AMP ASSIGN terminals.
Front B Bi-Amp :
The sound of the front B bi-amp channel is output
:The sound of the front height channel is output
from the speakers connected to the SURR.
BACK/AMP ASSIGN terminals.
Use ui to select “Cancel”, then use o p to select “Yes”.
the screen on
4 Once
the right appears,
Step2:Measurement
move
the
setup
microphone to the
second position, use
ui to select “Next”,
then press
.
Next
Calculate
Cancel
MultEQ
Please place microphone
at ear height at
2nd listening position.
[ENT]:Next
Measurements for the second position begin.
Analysis begins.
b Analysis
takes several
minutes
to
complete.
The time required for
this analysis depends on
the number of speakers
connected. The greater
the number of speakers
connected, the longer
analysis will take.
Step2:Measurement
MultEQ
All the measurements
were finished.
Calculate
Retry
Cancel
[ENT]:Cancel
⇩
Step3:Calculation
MultEQ
Calculating
Please wait...
[----------]
ui to select the item you want to check, then
7 Use
press
.
The measurement result
confirmation screen is
displayed.
b Subwoofers
or
other
speakers may be set to
a value that does not
correspond to the actual
distance.
Step4:Check
MultEQ
Please check the results
of the measured item.
Speaker Config.Check
Distance Check
Channel Level Check
Crossover Freq.Check
Next
[ENT]:Select
Specifications
n To cancel Audyssey Auto Setup
Measurements for the main listening position begin.
6
Once measurements
are finished, use ui
to select “Calculate”,
then press
.
Troubleshooting
from the speakers connected to the SURR.
BACK/AMP ASSIGN terminals.
you have checked the results, use ui to select
3 Once
“Next”, then press
.
position and positions around it. It is possible to stop the settings
with five positions or fewer, but for better results we recommend
measuring at six positions.
Information
and the screen on
the right appears,
check the results
of detection of the
connected speakers.
Step1:Speaker Detection
MultEQ
Front Sp.
:Yes
Center Sp.
:Yes
Subwoofer
:Yes
Surround Sp.
:Yes
S.Back Sp.
:Yes
:2sp
Next
Retry
[ENT]:Next
bMeasure at a total of six positions, including the main listening
Remote Control
all the speakers
2 Once
have been detected
:If the ZONE2 power is on, the sound of the
ZONE2 channel is output from the speakers
connected to the SURR. BACK/AMP ASSIGN
terminals.
Front A Bi-Amp :The sound of the front A bi-amp channel is output
Front Height
.
3-1.Audyssey Auto Setup
MultEQ
Please place microphone
at ear height at
main listening position.
Front Sp.: A
Amp Assign:
Normal
Start
Cancel
[ENT]:Select [RTN]:Back
Once measurements for the sixth position are completed, “All
the measurements were finished.” is displayed.
Multi-Zone
ZONE2
:The sound of the surround back channel is output
from the speakers connected to the SURR.
BACK/AMP ASSIGN terminals.
Playback
Normal
ui to select
1 Press
“Start”, then press
Perform Step 4 repeatedly for the 3rd, 4th, 5th, and
5 6th
measurments.
Settings
3-1.Audyssey Auto Setup
MultEQ
Please place microphone
at ear height at
main listening position.
Front Sp.: A
Amp Assign:
Normal
Start
Cancel
[ENT]:Select [RTN]:Back
•The Audyssey Auto Setup function detects the presence of each
speaker and automatically calculates the speaker size, channel
level, distance, and optimal crossover frequency setting. Audyssey
MultEQ corrects acoustical distortions within the listening area.
•Once started, MultEQ will play a series of test tones through each
speaker.
•Before starting, connect and position all of your speakers.
Connections
1 Press ui to select “Amp Assign”.
o p to select
2 Press
Amp Assign Mode.
Step 3 : Performing the Audyssey Auto Setup Procedure
Getting Started
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)
See overleaf
22
ENGLISH
Getting Started
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)
8 Press
NOTE
.
This returns you to analysis results items, so repeat
step 7.
Front
Connections
Settings
i to select “Next”, then
9 Press
press
.
ui to select
10Press
“Store”, then press
.
Playback
“Storing Please wait...” is
Multi-Zone
displayed on the on-screen
display while the results
are being stored.
When storing is complete,
“Storing complete. Auto
Setup is now finished.” is
displayed on the on-screen
display.
Step5:Store
MultEQ
Please select “Store”
to store measurement
values.
Store
Cancel
[ENT]:Store
⇩
Step5:Store
Remote Control
Storing
Please wait...
MultEQ
b If you do not want to save
Information
the measurement results,
use ui to select “Cancel”,
then select “Yes” using
o p. All the measured
Audyssey Auto Setup data
will be erased.
NOTE
Do not turn the power off while the settings are being stored.
Troubleshooting
the setup microphone from the AVR12Disconnect
1910.
Specifications
23
Do not change the speaker connections or subwoofer volume, or
speaker locations after making measurements. If changes are necessary, make the changes and use the Audyssey Auto Setup once again
for an updated EQ solution.
•If the result differs from the actual connection status or an error message appears, use ui to on-screen display “Retry” and then press
to repeat the measurement.
•If the result still differs from the actual connection status after remeasurement or the error message still appears, it is possible that
the speakers are not connected properly. Turn the AVR-1910 off,
check the speaker connections and repeat the measurement process from the beginning.
•For instance, If the location or direction of a speaker is altered, the
Audyssey Auto Setup should be performed again to ensure the correct EQ solution for the new room configuration.
ENGLISH
Error Messages
If the Audyssey Auto Setup procedure could not be completed due to speaker installation, the measuring environment, etc., an error message is
displayed. If this happens, check the relevant items, be sure to take the necessary measures, then perform the Audyssey Auto Setup procedure
over again.
Error messages (examples)
•Connect the included setup microphone to the
SETUP MIC jack on the main unit.
•Check the speaker connections.
then press
.
“Parameter Check” is
displayed on the on-screen
display.
Speaker Config.Check
Distance Chenck
Channel Level Check
Crossover Freq.Check
EQ Check
Restore
[ENT]:Select [RTN]:Back
Retry
Cancel
Front
Caution
Retry
Cancel
•Too much noise in the room for accurate
measurements to be made.
•Speaker or subwoofer sound is too low for
accurate measurements to be made.
•Either turn off any device generating noise or
move it away.
•Try again when the surroundings are quieter.
•Check the speaker installation and the direction
in which the speakers are facing.
•Adjust the subwoofer’s volume.
ui to select the item you want to check, then
2 Use
press
.
Speaker Config. Check :Check the speaker configuration
Distance Check
[ENT]:Retry
Caution
Front
R :None
]:CH
Caution
MultEQ
Front
L :Phase
]:CH
of
the
displayed
Channel Level Check
: Check the distance
: Check the channel level
Crossover Freq. Check :Check the crossover frequency
EQ Check
: Check the equalizer
o p to switch the display between the different
3 Use
speakers.
4 Press .
•Check the polarities of the displayed speaker.
•For some speakers, this error message may
be displayed even if the speaker is properly
connected. If you are sure that the wiring is
correct, press ui to select “Skip”, then press
.
The confirmation screen reappears. Repeat steps 2 and 3.
Even if the settings are changed after the Audyssey Auto Setup
procedure, the Audyssey Auto Setup settings can be restored by
selecting “Restore” then pressing
.
n To perform the Audyssey Auto Setup procedure again
Press ui to select “Retry”, then press
.
n To cancel Audyssey Auto Setup
Use ui to select “Cancel”, then select “Yes” using o p.
24
Specifications
[
Retry
Cancel
Skip
]:Up/Down [
connections
Troubleshooting
[
Retry
Cancel
Skip
]:Up/Down [
•Check the
speaker.
Information
MultEQ
•Displayed speaker could not be detected.
· The front R speaker were not properly detected.
· Only one channel of the surround speakers was
detected.
· Sound was output from the R channel when only
one surround back speaker was connected.
· The surround back, but the surround speaker was
not detected.
•Displayed speaker connected with the polarities
reversed.
Remote Control
MultEQ
FAmbient noise is
too high or
Level is too low.
Multi-Zone
[ENT]:Retry
Playback
•Not all speakers could be detected.
•The front L speaker was not properly detected.
Measures
3-2.Parameter Check
Settings
MultEQ
FMicrophone:None
or
Speaker
:None
Press ui to select
1 “Parameter
Check”,
Cause
•Included setup microphone is not connected.
Caution
This is displayed after the Audyssey Auto Setup procedure is
completed.
Connections
NOTE Be sure to turn the power off before checking the speaker connections.
Check Audyssey Auto Setup
Measurement Results (Parameter Check)
Getting Started
Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)
ENGLISH
Getting Started
Making detailed settings (Manual Setup)
Connections
Use this procedure to change the Audyssey Auto Setup settings or to change the various audio,
video and display settings.
The set can be used without changing these settings. Make these settings as necessary.
For a description of “Menu map” and operating instructions, see page 18.
Making the speaker settings (Speaker Setup)
Default settings are underlined.
Use this procedure to set the speakers manually or if you wish to change the settings made with
the Audyssey Auto Setup procedure.
n Items that can be set with the Manual Setup procedure
Settings
Making the speaker settings (Speaker Setup) vpage 25
Playback
Making the HDMI settings (HDMI Setup) vpage 28
Multi-Zone
Making the audio settings (Audio Setup) vpage 29
Remote Control
Making the ZONE2 settings (ZONE2 Setup) vpage 30
Setting items
Setting contents
Amp Assign
Sets the signal output to the
speaker connected to the
SURR. BACK/AMP ASSIGN
terminals.
Normal :The surround back channel audio signals are output.
ZONE2 :The ZONE2 audio signals are output.
Front A Bi-Amp : The bi-amp audio signals are output. Set this for bi-amp
playback of the front A speakers.
Front B Bi-Amp : The bi-amp audio signals are output. Set this for bi-amp
playback of the front B speakers.
Front Height : The front height channel audio signals are output.
Speaker Config.
Front : Set the front speaker size.
Select speaker configuration • Large : Use of a large speaker that can adequately play back low
frequencies.
and size.
(bass reproduction capability) • Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
Information
If “Subwoofer” is set to “No”, “Front” is automatically set to “Large”.
Center : Set the presence and size of the center speaker.
• Large : Use of a large speaker that can adequately play back low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when a center speaker is not connected.
Making other settings (Option Setup) vpage 30
n Examples of Menu Screen Displays
Speaker Setup
HDMI Setup
Audio Setup
Troubleshooting
4-1.Speaker Setup
4-2.HDMI Setup
4-3.Audio Setup
1.Amp Assign
2.Speaker Config.
3.Bass Setting
4.Distance
5.Channel Level
6.Crossover Freq.
7.Front Sp Setup
Auto Lipsync
: ON
HDMI Audio Out : Amp
HDMI Control
: OFF
1.EXT.IN SW Level
2.2ch Direct/Stereo
3.Auto Surround Mode
4.EQ Customize
Specifications
[ENT]:Select [RTN]:Back
[RTN]:Back
ZONE2 Setup
4-4.ZONE2 Setup
4-5.Option Setup
Level Lch
:
Level Rch
:
Vol.Display :
Vol.limit
:
Power On Lev:
Mute Lev.
:
1.Volume Control
2.Source Delete
3.On-Screen Display
4.Quick Select Name
5.ZONE Rename
6.Display
7.Setup Lock
0dB
0dB
Relative
OFF
Last
Full
[RTN]:Back
2
[ENT]:Select [RTN]:Back
Option Setup
Remote control
operation buttons
NOTE
Select “Large” or “Small” not
according to the physical size
of the speaker but according
to
the
low
frequency
reproduction
capabilities
based on the frequency set
at “Crossover Frequency”
(vpage 27).
• “Large” is not displayed when “Front” is set to “Small”.
• Even if “Center” has been set to “Large”, when “Front” is set to
“Small”, the “Center” setting automatically switches to “Small”.
• Subwoofer : Set the presence of a subwoofer.
• Yes : Use a subwoofer.
• No : Select when a subwooofer is not connected.
When “Front” is set to “Small”, “Subwoofer” can automatically set
to “Yes”.
[ENT]:Select [RTN]:Back
Displaying the menu
: Cancel the menu
See overleaf
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
Setting contents
Setting items
Speaker Config.
Select “Large” or “Small” not
according to the physical size
of the speaker but according
to
the
low
frequency
reproduction
capabilities
based on the frequency set
at “Crossover Frequency”
(vpage 27).
Remote control
operation buttons
•“Large” is not displayed when “Front” is set to “Small”.
•Even if “Front Height” is set to “Large”, the “Front Height” setting
is automatically switched to “Small” if “Front” is set to “Small”.
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
NOTE
Set the difference in the distance between the speakers to less than 6.0
meters (20 feet). “Relocate Speaker” is displayed on the screen if an
inappropriate distance is set.
Default : Reset all distance settings to factory default.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
: Decision the setting
: Return to previous menu
26
Specifications
Troubleshooting
NOTE
•The speakers that can be selected differ depending on the “Amp Assign”
(vpage 25) and “Speaker Config.” (vpage 25) settings.
•Default settings :
Front/Center/Subwoofer/Front Height : 3.6 meters (12 feet)
Surround/Surr. Back : 3.0 meters (10 feet)
Information
“Front
Height”
is
displayed when the “Amp
Assign” setting (vpage
25) is set to “Front
Height”.
Remote Control
NOTE
Even when the Surround Back Speaker setting is other than “None”,
sound may not be emitted from the surround back speaker, depending
on the playback source. In this case, “Surround Back” setting other
than “OFF” (vpage 45).
Front Height : Set the front height speaker size.
• Large : Use of a large speaker that can adequately play back low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when a front height speaker is not connected.
Multi-Zone
•“Large” is not displayed when “Surround” is set to “Small”.
•Even if “S.Back” is set to “Large”, the “S.Back” setting is automatically
switched to “Small” if “Surround” is set to “Small”.
Playback
Subwoofer Mode : Select low range signal to be reproduced by
Make the settings related to subwoofer.
playback of low frequency • LFE : Add the low frequency signal of the channel for which the speaker
signals (subwoofer and LFE). size is set to “Small” to the subwoofer signal and output it.
• LFE+Main : Add the low frequency signal of all channels to the subwoofer
This can be set when
signal and output it.
“Speaker
Config.”
–
•Play music or a movie source and select the mode offering the
“Subwoofer” (vpage
strongest bass.
25) is set to “Yes”.
•Select “LFE+Main” if you want the bass signals to always be
produced from the subwoofer.
LPF for LFE : Set the upper limit of the low frequency signals output from
the subwoofer.
• 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz
Unit : Set the unit of distance.
Distance
Set the distance from the • Feet
listening position to the • Meters
Step : Set the minimum variable width of the distance.
speakers.
Measure the distance from • 1ft / 0.1ft
the listening position to the • 0.1m / 0.01m
speakers beforehand.
• FL (Front L)/ FR (Front R)/ C (Center)/ SW (Subwoofer)/ SL (Surround L)/
SR (Surround R/ SBL (Surr. Back L)/ SBR (Surr. Back R)/ FHL (Front Height L)/
FHR (Front Height R) : Select the speaker you want to set, and set the
distance. Set the value that is closest to the measured distance.
• 0.0ft ~ 60.0ft / 0.00m ~ 18.00m
Settings
“Large” is not displayed when “Front” is set to “Small”.
S.Back : Set the presence, size and number of surround back speakers.
• Large : Use of a large speaker that can adequately play back low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when the surround back speakers are not connected.
• 2sp : Use two surround back speakers.
• 1sp : Use only one surround back speaker. Surround back audio is output
from the surround back L terminal.
Bass Setting
Connections
Surround : Set the presence and size of the Surround speakers.
Select speaker configuration • Large : Use of a large speaker that can adequately play back low
frequencies.
and size.
(bass reproduction capability) • Small : Use of a small speaker that has inadequate playback capacity for
low frequencies.
• None : Select when the surround speakers are not connected.
“S.Back” is displayed
when the “Amp Assign”
setting (vpage 25) is
set to “Normal”.
Setting contents
Setting items
Getting Started
Making detailed settings (Manual Setup)
ENGLISH
Getting Started
Making detailed settings (Manual Setup)
Setting contents
Setting items
Channel Level
Connections
Set the volume of the test
tone to be the same when it
is output from each speaker.
Settings
Test Tone Start : Output test tones.
FL (Front L)/ C (Center)/ FR (Front R)/ SR (Surround R)/
SBRz (Surround Back R)/ SBLz (Surround Back L)/ SL (Surround L)/
FHL (Front Height L)/ FHR (Front Height R)/ SW (Subwoofer) : Select
the speaker.
zWhen the “S.Back” setting (vpage 26) is set to “1sp”, “SB” is
displayed.
• –12.0dB ~ +12.0dB (0.0dB) : Adjust the volume.
Playback
•When “Channel Level” is adjusted, the adjusted values are set for
all the surround modes. To adjust the channel level separately for the
different surround modes, use the operation see “Adjust the volume of
the different speakers” (vpage 50).
•Speakers set to “None” in the “Speaker Config.” (vpage 25) settings
are not displayed.
•When o is pressed while the subwoofer volume is set to “–12dB”, the
“Channel Level” setting switches to “OFF”.
•If output of the test tones begins while the muting mode is set, the
muting mode is canceled.
Multi-Zone
Remote Control
Information
Crossover Frequency
Troubleshooting
Outputs at below set
frequency, each speaker’s
bass signal output from the
subwoofer. Set this according
to the low frequency
reproduction capabilities of
the speakers you are using.
Specifications
This can be set when
“Speaker Config.” –
“Subwoofer” (vpage
25) is set to “Yes” or
“No”.
27
Crossover Frequency
•Always set the crossover frequency to “80 Hz”. When using small
speakers, however, we recommend setting the crossover frequency
to a higher frequency.
•For speakers set to “Small”, sound below the crossover frequency
is cut from the sound output. The cut bass sound is output from the
subwoofer or front speakers.
•The speakers that can be set when “Advanced” is selected differ
according to the “Bass Setting” setting (vpage 26).
· When “LFE” is selected, speakers set to “Small” at “Speaker
Config.” (vpage 25) can be set.
· When “LFE+Main” is selected, speakers can be set regardless of
the speaker size setting.
Setting : Choose the method for setting the front speakers.
Front Speaker Setup
.
Select front speakers to use • Normal : The front speakers are set using the
• Custom : The front speakers used for the different playing modes are
for each surround mode.
set in advance.
Default : Reset all channel level settings to factory default.
Yes : Reset to the defaults.
No : Do not reset to the defaults.
Crossover : Outputs at below set frequency, each speaker’s bass signal
output from the subwoofer.
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz
• Advanced : Set the low frequency signals to be output from the signals
of the respective speakers to the subwoofer.
• Front / Center / Surround / S.Back / Front Height : Select the speaker.
· 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
250Hz : Set the crossover frequency.
Remote control
operation buttons
Displaying the menu
: Cancel the menu
Setting contents
Setting items
: Moves the cursor (Up/Down/Left/Right)
DIRECT/STEREO : The front speakers used in the direct, stereo and pure
direct play modes are set in advance.
• A : Front speaker A is used.
• B : Front speaker B is used.
• A+B : Both front speakers A and B are used.
MULTI CH : The front speakers used in modes other than the direct, stereo
and pure direct play modes are set in advance.
• A : Front speaker A is used.
• B : Front speaker B is used.
• A+B : Both front speakers A and B are used.
NOTE
•When set to “Custom”,
does not operate.
•The front speaker setting stored for the “Quick Select” function is given
priority.
: Decision the setting
: Return to previous menu
ENGLISH
Setting items
Making the HDMI settings(HDMI Setup)
Default settings are underlined.
Setting items
Setting contents
ON : Compensated.
OFF : Not compensated.
Playback
Amp : Use speakers connected to AVR-1910 for audio playback.
TV : Use speakers of TV for audio playback.
NOTE
Remote Control
NOTE
Multi-Zone
When the HDMI control function is operating, the setting of audio playback
in the connected TV takes priority (vpage 49 “Controlling HDMIcompatible devices from the AVR-1910 (HDMI Control Function)”).
HDMI Control
ON : Use the HDMI control function.
External devices can be OFF : Do not use the HDMI control function.
controlled from the AVR• Please consult the operating instructions for each connected device
1910 and the AVR-1910 can
to check the settings.
be controlled from external
•
For details on the HDMI control function, see “Controlling HDMIdevices.
compatible devices from the AVR-1910 (HDMI Control Function)”
(vpage 49).
NOTE
Information
• When “Control” is set to “ON”, it consumes more standby power.
• When not using this unit for a long period, we recommend that you press
to turn off (jOFF) the power.
• When the “HDMI Control” setting has been changed, always turn off the
power to the connecting devices afterwards and then turn back on.
• The “HDMI Control” does not work when the power to the equipment is
off.
• When “HDMI Control” is set to “ON”, power is supplied constantly to the
AC outlet (UNSWITCHED).
Troubleshooting
The
HDMI
control
function
controls
operations of a TV that
is compatible with the
HDMI control function.
Make sure that the TV
and HDMI are connected
when you perform HDMI
control.
Specifications
Standby Source
Last : Standby with last used input source during power on.
Set the HDMI connector for HDMI1 / HDMI2 / HDMI3 / HDMI4 : The standby mode is set at the input
HDMI signal input during source assigned to the respective.
standby.
This can be set when
“HDMI Control” is set
to “ON”.
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
Settings
Auto Lip Sync
Automatic
compensation
for timing shift in audio and
video output.
HDMI Audio Out
Select HDMI audio output
device.
Power Off Control
ON:Switched.
The power of the AVR-1910 OFF:Not switched.
and external device turn off
• Please consult the operating instructions for each connected device
together.
to check the settings.
• For details on the HDMI control function, see “Controlling HDMIThis can be set when
compatible devices from the AVR-1910 (HDMI Control Function)”
“HDMI Control” is set
to “ON”.
(vpage 49).
Connections
Make settings for HDMI video/audio output.
Setting contents
Getting Started
Making detailed settings (Manual Setup)
: Decision the setting
: Return to previous menu
28
ENGLISH
Getting Started
Making detailed settings (Manual Setup)
Making the audio settings (Audio Setup)
Default settings are underlined.
Connections
Make settings for audio playback.
Settings
Playback
Setting items
Setting contents
EXT.IN SW Level
Set the playback level of the
analog subwoofer signals
input from the external input
terminals (EXT.IN).
2ch DIRECT/STEREO
Make speaker settings for 2channel mode playback.
+15dB : This is the recommended level.
+10dB / +5dB / 0dB : Select the level according to the player being used.
Multi-Zone
Remote Control
Information
Troubleshooting
Specifications
2
Setting : Select the method for setting the speakers used in the 2-channel
direct and stereo playback modes.
• Basic : The settings at “Speaker Setup” (vpage 25) are applied.
• Custom : Make separate settings for 2-channel mode.
Front : Set the front speaker size.
• Large : Use of a large speaker that can adequately play back low
frequencies.
• Small : Use of a small speaker that has inadequate playback capacity
for low frequencies.
SW : Set the presence of a subwoofer.
• Yes : Use a subwoofer.
• No : Select when a subwoofer is not connected.
SW Mode : Select low range signal to be reproduced by subwoofer.
• LFE : Add the low frequency signal of the channel for which the speaker
size is set to “Small” to the subwoofer signal and output it.
• LFE+Main : Add the low frequency signal of all channels to the
subwoofer signal and output it.
Crossover : Outputs at below set frequency, each speaker’s bass signal
output from the subwoofer.
• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz
/ 250Hz
Distance FL / Distance FR : Select the speaker you want to set, and set
the CH Level. Set the value that is closest to the measured distance.
• 0.0ft ~ 60.0ft (12.0ft) / 0.00m ~ 18.00m(3.6m)
CH Level FL/ CH Level FL FR : Select the speaker you want to set, and
set the CH Level. Adjust the level of each channel.
• –12.0dB ~ +12.0dB(0.0dB)
Remote control
operation buttons
Displaying the menu
: Cancel the menu
Setting items
Setting contents
Auto Surround Mode
Make setting for memorizing
surround mode setting for
each input signal type.
ON : Memorize settings. Most recently stored surround mode is
automatically selected.
OFF : Do not memorize settings. Surround mode does not change
according to input signal.
The auto surround mode function lets you store in the memory the
surround mode last used for playing the four types of input signals
listed below.
q Analog and PCM 2-channel signals
w Dolby Digital and DTS 2-channel signals
e Dolby Digital and DTS multi-channel signals
r Multi-channel signals other than Dolby Digital and DTS (PCM, etc.)
NOTE
When playing in the PURE DIRECT mode, the surround mode does not
change even if the input signal is changed.
EQ Customize
Audyssey Byp. L/R / Audyssey Flat / Manual
Set so that unused equalizer • Used
settings are not displayed • Not Used
when
is used.
: Moves the cursor (Up/Down/Left/Right)
NOTE
• Set so that the “Audyssey Byp. L/R” and “Audyssey Flat” settings can be
made when the Audyssey Auto Setup procedure is performed.
• Equalizer settings for which “Not Used” is set with the Quick Select
function cannot be stored and called out.
: Decision the setting
: Return to previous menu
ENGLISH
Making the ZONE2 settings (ZONE2 Setup)
Making other settings (Option Setup)
Default settings are underlined.
Setting items
–12dB ~ +12dB (0dB)
–12dB ~ +12dB (0dB)
Information
NOTE
•The currently selected input source cannot be set.
•Input sources set to “Delete” cannot be selected using
.
See overleaf
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
0
Specifications
Master Volume : Master volume display during adjustment.
• Bottom : Displayed at the bottom of the screen.
• Top : Displayed at the top of the screen.
• OFF : Turn display off.
Troubleshooting
On-Screen Display
Screensaver : Make screensaver settings.
Make the settings related to • ON : The screen switches to the screensaver if no operation is performed
displays on the TV screen.
for approximately 3 minutes while a menu is displayed or while an iPod
screen is displayed. When you press uio p, the screen saver is
cancelled and the screen before that screen saver started is displayed.
• OFF : Turn the screensaver function off.
Text : The mode name is displayed when the operation for switching the
surround mode, input mode, etc., is performed.
• ON : Turn display on.
• OFF : Turn display off.
Remote control
operation buttons
Remote Control
Power On Level : This sets the volume set when the MAIN ZONE’s power
is turned on.
• Last : Use the memorized setting from the last session.
• – – – : Always use the muting on condition when power is turned on.
• –80dB(1) ~ +18dB(99) : The volume is adjusted to the set level.
Mute Level : This sets the amount of attenuation of the volume when the
mute mode is set in the MAIN ZONE.
• Full : The sound is cut off entirely.
• –40dB : The sound is attenuated by 40 dB.
• –20dB : The sound is attenuated by 20 dB.
Source Delete
TUNER / CD / DVD / HDP / TV / SAT/CBL / VCR / DVR / V.AUX /
Remove
input
sources SIRIUS: Select the sources you do not want to use.
that are not used from the • ON : Use this source.
display.
• Delete : Do not use this source.
Multi-Zone
• The volume is displayed using the display method set at “Volume Display” (vpage 30).
•Set the main volume at “Volume Control” (vpage 30).
Volume Control
Volume Display : Set the volume display method.
Set the MAIN ZONE volume • Relative : The volume is displayed within the range of – – –dB (Minimum),
setting.
–80 dB ~ +18 dB.
• Absolute : The volume is displayed within the range of 0, 1 ~ 99.
Vol.Limit : Make a setting for maximum volume.
• OFF : Do not set a maximum volume.
• –20dB(61) / –10dB(71) / 0dB(81)
Playback
Relative : The volume is displayed within the range of – – –dB (Minimum),
–80 dB ~ +18 dB.
Absolute : The volume is displayed within the range of 0, 1 ~ 99.
Vol.Limit
OFF : Do not set a maximum volume.
Make a setting for maximum –20dB / –10dB / 0dB
volume.
Power On Level
Last : Use the memorized setting from the last session.
Define the volume setting – – – : Always use the muting on condition when power is turned on.
that is active when the power –80dB ~ +18dB (99) : The volume is adjusted to the set level.
is turned on.
Mute Level
Full : The sound is cut off entirely.
Set the amount of attenuation –40dB : The sound is attenuated by 40 dB.
when muting is on.
–20dB : The sound is attenuated by 20 dB.
Setting contents
Settings
Level Lch
Adjust the left channel output
level.
Level Rch
Adjust the right channel
output level.
Volume Display
Set the ZONE2 volume
display method.
Setting contents
Setting items
Connections
Make settings for audio playback in a ZONE2 system.
“ZONE2 Setup” is displayed when ZONE2 is selected with “Amp Assign” (vpage 25).
Default settings are underlined.
Getting Started
Making detailed settings (Manual Setup)
ENGLISH
Getting Started
Making detailed settings (Manual Setup)
Setting items
Setting contents
Setting items
Connections
On-Screen Display
Tuner Information : This sets the time the on-screen display is displayed
Make the settings related to when a tuner operation is performed.
displays on the TV screen.
• Always : Show display continuously.
• 30sec : Show display for 30 seconds after operation.
• 10sec : Show display for 10 seconds after operation.
• OFF : Turn display off.
Settings
Playback
Multi-Zone
iPod Information : This sets the time the on-screen display is displayed
when an iPod operation is performed.
• Always : Show display continuously.
• 30sec : Show display for 30 seconds after operation.
• 10sec : Show display for 10 seconds after operation.
• OFF : Turn display off.
Quick Select Name
Rename Label : Change the display name of the selected “Quick Select”
Change the Quick Select setting.
name.
1.Use ui to select the name of the Quick Select setting you want
to change, then press
.
2.Use o p to set the cursor to the character you want to change.
3.Use ui to change the character, then press
.
Remote Control
• Up to 16 characters can be input.
• The input character type can be switched by pressing
while the
display name is being changed.
• The types of characters that can be input are as shown below.
Information
GCapital lettersH A B C D E F G H I J K L M N O P Q RST U V W X Y Z
GSmall lettersH a b c d e f g h i j k l m n o p q r s tu v w x y z
GSymbolsH
’()b+–./:;<=>?[]
GNumbersH
01 2 3 4 5 6 7 8 9 (space)
Troubleshooting
4.Repeat steps 2 and 3 to change the display name.
Template : The display name can be changed by selecting “Operation” and
“Device Name” from the previously set templates.
Quick Select Name
Default : The changed display names are reset to the defaults.
• Yes : Reset to the defaults.
• No : Do not reset to the defaults.
Zone Rename
1.Use ui to select the zone name you want to change, then press
Rename the display names
.
of the different zones as
MAIN ZONE / ZONE2
desired.
2.Use o p to set the cursor to the character you want to change.
3.Use ui to change the character, then press
.
• Up to 10 characters can be input.
• The input character type can be switched by pressing
while the
display name is being changed.
• The types of characters that can be input are as shown below.
GCapital lettersH ABCDEFGHIJKLMNOPQRSTUVWXYZ
GSmall lettersH abcdefghijklmnopqrstuvwxyz
GSymbolsH
’()b+–./:;<=>?[]
GNumbersH
0123456789 (space)
4.Repeat steps 2 and 3 to change the display name.
Display
• Bright : Normal display brightness.
Adjust display brightness of • Dim : Reduced display brightness.
the receiver.
• Dark : Very low display brightness.
• OFF : Turns the display off.
Setup Lock
Protect
settings
inadvertent change.
1.Use ui to select the name of the Quick Select setting you want
to change, then press
.
2.Use ui to select “Template”, then press
.
.
3.Use ui to select “Operation”, then press
Specifications
• Watch / Listen to / Play / For
4.Use uio p to select “Device Name ”, then press
Setting contents
Switching is also possible by pressing
• ON : Turn protection on.
from • OFF : Turn protection off.
on the main unit.
When “Setup Lock” is set to “ON”, the settings listed below can
no longer be changed. Also, “SETUP LOCKED!” is displayed if you
attempt to operate related settings.
・RESTORER
・Dynamic Volume
・MultEQ
・Channel Level
・Dynamic EQ
・Audio Delay
.
•DVD / Blu-Ray / HDP / TV / Cable TV / Satellite / VCR / DVR / iPod /
V.AUX / LD / Movie (When “Operation” is selected to “Watch”.)
•CD / TUNER / SIRIUS / iPod / MD / TAPE / MUSIC (When
“Operation” is selected to “Listen to”.)
•PC / Game (When “Operation” is selected to “Play”.)
•Father / Mother / Son / Daughter / Brother / Sister / Grandfather
/ Grandmother / Me (When “Operation” is selected to “For”.)
31
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
DVD
HDP
TV
SAT/CBL
VCR/iPod
DVR
1
2
02
2
Input Mode
Decode Mode
[RTN]:Back
Rename
[RTN]:Back
Source Level
iPod Playback Mode
5-5.Source Level
Analog Input
Digital Input
: DVD
: Auto
: Auto
5-6.iPod Playback Mode
:
:
0dB
0dB
Repeat Mode
Shuffle Mode
:
:
One
OFF
Defaulut
[
]:Up/Down [ ]:Rename
[RTN]:Back
[RTN]:Back
Auto Preset
5-1.Auto Preset
Auto Tuning
Preset Station Memory
Storing Preset Memory
[ENT]:Start [RTN]:Back
5-2.Preset Skip
Block
:
A Block Presets:
A1 FM 87.50MHz :
A2 FM 89.10MHz :
A3 FM 98.10MHz :
A4 FM107.90MHz :
A5 FM 90.10MHz :
A6 FM 90.10MHz :
A7 FM 90.10MHz :
A8 FM 90.10MHz :
Parental Lock
5-2.Parental Lock
A
ON
ON
ON
ON
ON
ON
ON
ON
ON
5-3.Preset Name
Block: A
A1FM 87.50MHz:
A2FM 89.10MHz:
A3FM 98.10MHz:
A4FM107.90MHz:
A5FM 90.10MHz:
A6FM 90.10MHz:
A7FM 90.10MHz:
A8FM 90.10MHz:
[ENT]:Select [RTN]:Back
Antenna Aiming
5-3.Antenna Aiming
Setting the Preset Channels to be Skipped (Preset Skip) vpage 36
Satellite
MIN
Troubleshooting
1.Lock Setting
2.Edit Lock Code
Assign Name to a Preset Memory (Preset Name) vpage 36
Preset Name
:0
MAX
Terrestrial :0
MIN
MAX
Specifications
[ENT]:Select [RTN]:Back
Setting Radio Reception Restrictions (Parental Lock) vpage 37
Check the SIRIUS Radio Reception Sensitivity (Antenna Aiming)
vpage 37
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
Information
Start
Presetting Radio Stations (Auto Preset) vpage 36
[RTN]:Back
Preset Skip
Remote Control
Setting the iPod Playback Mode (iPod Playback Mode) vpage 35
4
Source
Anlg/HDMI
Auto
Auto
Auto
Full
Multi-Zone
Correcting the Input Source’s Playback Level (Source Level)
vpage 35
01
C2
5-4.Rename
DVD
Changing the Input Source’s Display Name (Rename) vpage 35
3
Input Mode
5-3.Input Mode
Video Select:
i/p Scaler :
Resolution A:
Resolution H:
Progre.Mode :
Aspect
:
1
[ENT]:Select [RTN]:Back
Making the video settings (Video) vpage 34
Changing the Input Source’s Input Mode and Decoding mode (Input
mode) vpage 34
C1
Video
5-2.Video
Playback
Changing the Input Sources Assigned to the Input Terminals (Assign)
vpage 33
Assign
5-1-1.Input Assign
HDMI Digi Comp
Settings
n Items that can be set with the Input Setup procedure
n Examples of Menu Screen Displays
Connections
Make the settings related to the currently selected input source.
Before displaying the menu screen, press
to switch to the input source to be set.
The items that can be set differ according to the selected input source.
The set can be used without changing these settings. Make these settings as necessary.
For a description of “Menu map” and operating instructions, see page 18.
Getting Started
Making the input settings (Input Setup)
: Return to previous menu
2
ENGLISH
Getting Started
Making the input settings (Input Setup)
Changing the Input Sources Assigned to the Input Terminals
(Assign)
Default settings are underlined.
Connections
Setting items
Setting contents
Settings
Input Assign (HDMI)
TV
SAT/CBL VCR
DVR V.AUX input
HDMI : The DVD HDP
Assign input sources to input
sources are assigned to the HDMI input terminals as shown below.
connectors.
• HDMI1 / HDMI2 / HDMI3 / HDMI4
• None : Do not assign an HDMI input terminal to the currently selected
input source.
Setting items
Setting contents
Input Assign (Component)
TV
SAT/CBL VCR DVR V.AUX
Component : The DVD HDP
Assign input sources to input
input sources are assigned to the component video input terminals as
connectors.
shown below.
● COMP1 (Component video 1 input terminal) / COMP2 (Component
video 2 input terminal)
● None : Do not assign the component video input terminals to the currently
selected input source.
bUpon purchase, the settings of the different input sources are as shown
below.
Playback
bUpon purchase, the settings of the different input sources are as shown
below.
Multi-Zone
Input
source
Default
setting
DVD
HDP
HDMI1 HDMI2
TV
SAT/CBL
VCR
DVR
V.AUX
None
HDMI3
None
HDMI4
None
Remote Control
Information
•When HDMI is assigned to an input source, the audio signal switches
to HDMI along with the video signal. To use with the digital audio
input connectors assigned, set menu “Input Mode” (vpage 34) to
“Digital”.
•When the AVR-1910 and TV are connected with an HDMI cable, if the
TV is not compatible with HDMI audio signal playback, only the video
signals are output to the monitor.
•The audio signals input from the analog, digital and EXT. IN connectors
are not output to the TV.
Input
source
DVD
HDP
TV
SAT/CBL
VCR
DVR
V.AUX
Default
setting
COMP1
None
None
None
None
COMP2
None
iPod Dock
The control dock for iPod can be assigned to the DVD SAT/CBL VCR
Change the input source to
DVR V.AUX
CD input sources.
which the control dock for
Assign
:
Assign
the
currently selected input source to the Control Dock for
iPod is assigned.
iPod input.
None : Do not assign the currently selected input source to the Control Dock
for iPod input.
•With the default settings, the control dock for iPod can be used
connected to the VCR (iPod) connector.
•Even if “iPod Dock” is set to “Assign”, if AVR-1910 and control dock
for iPod are not connected, the input is used as the normal input
source.
NOTE
Troubleshooting
When “HDMI Control” is set to “ON”, HDMI cannot be assigned to “TV”
at the “HDMI” settings (vpage 28).
Specifications
Input Assign (Digital)
TV
SAT/CBL VCR DVR V.AUX
CD
Digital : The DVD HDP
Assign input sources to input
input sources are assigned to the digital audio input terminals as
SIRIUS
connectors.
shown below.
• C1 (COAX1) / C2 (COAX2) / O1 (OPT1) / O2 (OPT2)
• None : Do not assign a digital input terminal to the currently selected
input source.
bUpon purchase, the settings of the different input sources are as shown
below.
Input source
DVD
HDP
TV
SAT/CBL
VCR
COAX1
None
OPT1
COAX2
None
Input source
DVR
V.AUX
CD
SIRIUS
Default setting
OPT2
None
None
None
Default setting
33
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
Making the video settings (Video)
Default settings are underlined.
Changing the Input Source’s Input Mode and Decoding mode
(Input Mode)
Default settings are underlined.
NOTE
Setting items
.
to select “Source”.
TV
SAT/CBL
VCR
Default
setting
Auto
HDMI
Digital
Auto
Analog
Input
source
DVR
V.AUX
CD
TUNER
Default
setting
Auto
Analog
Analog
Analog
•The “HDMI” settings are made for input sources for which HDMI
input terminals are assigned at “Assign” (vpage 33).
•The “Digital” settings are made for input sources for which digital
input terminals are assigned at “Assign” (vpage 33).
•When a digital signal is properly input, the “
” indicator lights on
the display. If the “
” indicator does not light, check the digital
input connector assignment and the connections.
•The surround mode cannot be set if the input mode is set to “EXT.
IN”.
•This can also be set by pressing
.
Each time you press the button, the input mode display will change.
Auto
HDMI
EXT. IN
: Decision the setting
Digital
Analog
: Return to previous menu
34
Specifications
: Moves the cursor (Up/Down/Left/Right)
HDP
Troubleshooting
Displaying the menu
: Cancel the menu
DVD
Information
Remote control
operation buttons
Input
source
Remote Control
•To cancel, press
i/p Scaler
TV SAT/CBL VCR DVR V.AUX
This can be set to the DVD HDP
The input source’s resolution
input sources.
is converted to the resolution
OFF : Do not use i/p scaler function.
set at “Resolution”.
Analog : Analog signals are converted to HDMI signals.
Analog and HDMI : Both analog signals and HDMI signals are converted
to the desired HDMI resolution.
Resolution
This can be set when the input source is set to DVD
HDP
TV
Set the output resolution.
SAT/CBL VCR DVR V.AUX , and when “i/p Scaler” is set to anything
Resolution A : Analog Video
other than “OFF”.
Resolution H : HDMI
AUTO : Detect monitor panel resolution and automatically set output
resolution.
480p/576p / 1080i / 720p / 1080p : Select the output resolution.
Progressive Mode
This can be set when the input source is set to DVD
HDP
TV
Select optimum progressive
SAT/CBL VCR DVR V.AUX , and when “i/p Scaler” is set to anything
mode for video material.
other than “OFF”.
AUTO : The video material is automatically detected and the appropriate
mode is set.
Video1 : Select mode suitable for video playback.
Video2 : Select mode suitable for video and 30-frame film material
playback.
Aspect
This can be set when the input source is set to DVD
HDP
TV
Set the aspect ratio of the
SAT/CBL VCR DVR V.AUX , and when “i/p Scaler” is set to anything
video signal output from the
other than “OFF”.
HDMI terminal.
Normal : Output at 4:3 aspect ratio.
Full : Output at 16:9 aspect ratio.
bUpon purchase, the settings of the different input sources are as shown
below.
Multi-Zone
•This can also be set by pressing
Setting contents
Input Mode
Auto : Automatically detect input signal and perform playback.
Set the audio input modes for HDMI : Play only signals from HDMI input. (Excluding CD and SIRIUS)
the different input sources. Digital : Play only signals from digital input.
Analog : Play only signals from analog input.
EXT. IN : Play only signals from EXT. IN input.
Playback
• It is not possible to select HDMI input signals.
• When playing HDMI video input signals, the analog video signal of
another input source cannot be selected for the HDMI video output.
• Input sources for which “Delete” is selected at “Source Delete” (vpage
30) cannot be selected.
• Input sources for which “None” is selected at “Assign” (vpage 33)
cannot be selected.
The selectable input modes depend on the input source and “Assign” setting (vpage
33 “Changing the input sources assigned to the input terminals”).
Settings
Setting items
Setting contents
Video Select
Source : Play the picture and sound of the input source.
Switch video input source DVD / HDP / TV / SAT/CBL / VCR / DVR / V.AUX : Select video input
while listening to audio source to view. This can be set for individual input sources.
signal.
Connections
The items that can be set depend on the input source and the “Assign” setting.
Getting Started
Making the input settings (Input Setup)
ENGLISH
Getting Started
Making the input settings (Input Setup)
Setting items
Decode Mode
Set the input
decoding mode.
Setting contents
Connections
Auto : Detect type of digital input signal and decode and play
source’s automatically.
PCM : Decode and play only PCM input signals.
DTS : Decode and play only DTS input signals.
Settings
•This can be set for input sources for which “HDMI” or “Digital” is
assigned at “Assign” (vpage 33).
•Normally set this to “Auto”.
Playback
Changing the Input Source’s Display Name (Rename)
Default settings are underlined.
Correcting the Input Source’s Playback Level
(Source Level)
Default settings are underlined.
Use this procedure to correct the playback level of the currently selected input source's audio input.
Set this if there are differences in the input volume levels between the different sources. The analog
input level and digital input level can be corrected separately.
Setting items
Setting contents
Source Level (Analog)
–12dB ~ +12dB (0dB)
Correct the playback level of
the analog audio input.
Source Level (Digital)
–12dB ~ +12dB (0dB)
Correct the playback level of
the digital audio input.
Multi-Zone
Use this procedure to change the display name of the currently selected input source.
Setting items
Setting contents
Remote Control
Rename
1.Use o p to set the cursor to the character you want to change.
Change the input source’s 2.Use ui to change the character, then press
.
display name to the desired
• Up to 8 characters can be input.
name.
• The input character type can be switched by pressing
while the
display name is being changed.
• The types of characters that can be input are as shown below.
Information
GCapital lettersH A B C D E F G H I J K L M N O P Q RST U V W X Y Z
GSmall lettersH a b c d e f g h i j k l m n o p q r s tu v w x y z
GSymbolsH
’()b+–./:;<=>?[]
GNumbersH
01 2 3 4 5 6 7 8 9 (space)
Troubleshooting
Default
Yes : Reset to the defaults.
The changed display names No : Do not reset to the defaults.
are reset to the defaults.
Setting the iPod Playback Mode (iPod Playback Mode)
Default settings are underlined.
This can be selected for input sources for which “Assign” is assigned at the “iPod Dock” (vpage
33) setting.
Setting items
Setting contents
Repeat
All : Repeat all songs.
Make settings for repeat One : Repeat the current song.
mode.
OFF : Cancel repeat mode.
Shuffle
nWhen DENON control dock for iPod ASD-1R or ASD-11R is
Make settings for shuffle
connected
mode.
Songs : Shuffle all songs.
Albums : Shuffle songs from current album only.
OFF : Cancel shuffle mode.
Specifications
35
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
Assign Name to a Preset Memory (Preset Name)
Presetting Radio Stations (Auto Preset)
Default settings are underlined.
Setting contents
Setting items
Auto Preset
This can be set when the source is set to TUNER .
Use the auto preset function
Start : Start the auto preset process.
to program radio stations.
Setting contents
Preset Name
This can be set when the source is set to TUNER .
Assign name to a preset
1.Use ui to select the preset channel name you want to change,
memory.
then press
.
2.Use o p to set the cursor to the character you want to change.
3.Use ui to change the character, then press
.
•Up to 8 characters can be input.
Default settings are underlined.
Setting contents
4.Repeat steps 2 and 3 to change the display name.
Remote Control
Preset Skip
This can be set when the source is set to TUNER SIRIUS .
Set the preset memories that
A ~ G : Select the preset channel(s) you do not want to display.
you do not want to display
• ON : Display this number.
when tuning.
• Skip : Skip this number.
GCapital lettersH ABCDEFGHIJKLMNOPQRSTUVWXYZ
GSmall lettersH abcdefghijklmnopqrstuvwxyz
GSymbolsH
’()b+–./:;<=>?[]
GNumbersH
0123456789 (space)
Multi-Zone
Setting items
•The input character type can be switched by pressing
while the
display name is being changed.
•The types of characters that can be input are as shown below.
Playback
Setting the Preset Channels to be Skipped (Preset Skip)
Settings
If an FM station cannot be preset automatically, select the desired station
by tuning it in manually, then preset it manually.
Connections
Setting items
Default settings are underlined.
Getting Started
Making the input settings (Input Setup)
Information
If you set “Block Presets” to “Skip”, you can skip the preset memory
blocks (A to G).
Troubleshooting
Specifications
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
36
ENGLISH
Getting Started
Making the input settings (Input Setup)
Setting Radio Reception Restrictions (Parental Lock)
Default settings are underlined.
Connections
Setting items
Lock Setting
Set the channel
reception limits.
Check the SIRIUS Radio Reception Sensitivity
(Antenna Aiming)
Default settings are underlined.
Setting contents
radio
Settings
This can be set when the source is set to SIRIUS .
1. Press
.
2. Using uio p, input the password (4 digits number) and press
.
3. Select channel by pressing ui, and set the lock by pressing o p.
• Unlock : Do not lock selected channel(s).
• Lock : Lock selected channel(s).
Playback
bWhen a Parental Locked channel is tuned, “Code : [
then input the password.
Setting items
Antenna Aiming
Check the SIRIUS
reception sensitivity.
Setting contents
radio
This can be set when the source is set to SIRIUS .
Satellite : Indicate satellite signal strength.
Terrestrial : Indicate terrestrial signal strength.
SIRIUS Antenna
Display
]” is displayed,
Multi-Zone
• The default password is “0000”.
• If the password is wrong, “Incorrect Code” is displayed. Input the correct
password.
• While listening to the channel being played, you can also set parental lock
(vpage 41).
Remote Control
Edit Lock Code
Change the password.
Condition
Signal strength is excellent
Signal strength is good
Signal strength is weak
No signal
This can be set when the source is set to SIRIUS .
1. Press
.
2.Input “Current Code” (4 digits) using uio p, and press
3. Input “New Code” (4 digits) using uio p, and press
.
.
Information
4.Input “Repeat Code” (4 digits) again using uio p, and press
. If
the correct password is input, “Completed” is displayed, and the new
password is modified.
Troubleshooting
Specifications
• If the “Current Code” is incorrectly input, “Incorrect Code” is displayed,
and proceed again from step 1.
• If the password input is 3 digits or less, “Enter 4-digit” is displayed, and
input again with a 4 digit password.
• If the new password is not correctly input, “Code don’t Match” is displayed
and the password does not change.
• The password cannot be cleared even if the operation to reset the unit is
performed. We recommend writing down the password so as not to forget
it.
37
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
Playing Components
n Operation Flow
Before starting playback, make the connections between the
different components and the settings on the receiver.
Playing Components (vpage 38)
2
r Stereo Playback (vpage 44)
If “TUNING PRESET” is selected for
preset channel, press
before turning
NOTE
Also refer to the operating instructions of the connected
components when playing them.
● External devices can be controlled by remote control unit
(vpage 52 “Operating the Connected Devices by Remote
Control Unit”).
●
the component connected to
4 Play
theAVR-1910.
(vpage 33).
to “MAIN/TV”
eSet
2
3
to “MAIN”.
TurnontheAVR-1910’spower.
(vpage 17“Turning the Power On”)
Press toselecttheinputsourceassignedinstep1wabove.
Front
Make the necessary settings on the
player (language setting, subtitles
setting,etc.)beforehand.
5
Use
toadjustthevolume.
GVariable rangeH
–––
–80.0dB ~ 18.0dB
※The variable range differs according to the input signal and channel
OKtodisconnect.
(iPod screen)
b If the screens above are not displayed, the iPod may not be
properly connected. Try connecting again.
level setting.
6 Selectthedesiredsurroundmode.
7 Adjustthedesiredsoundfieldeffects.
(vpage 42“Selecting the Surround Mode”)
(vpage 44“Adjusting the Sound Field Effects”)
See overleaf
8
Specifications
Adjusting the Sound Field Effects (Parameter)
(vpage 44)
.
for iPod.
w Assign the control dock for iPod’s input
Troubleshooting
t Playing the Pure Direct mode (vpage 44)
and select the input
Front
q Set the iPod in the DENON control dock
Information
e Direct Playback (vpage 43)
1 Prepareforplayback.
(vpage 17“Turning the Power On”)
3 Press
source.
q Standard Playback (vpage 42)
w Playing in a DENON original surround mode
(vpage 43)
TurnontheAVR-1910’spower.
Listening to music on an iPod®
Remote Control
Selecting the Surround Mode (vpage 42)
①Turn on the power of the TV, subwoofer and player.
②Set the TV’s input to the AVR-1910.
Front
③Load the disc in the player.
Multi-Zone
n Operations During Playback (vpage 42)
1Prepareforplayback.
The music / video on an iPod can be played by using the control
dock for iPod (ASD-1R, ASD-11R, ASD-3N or ASD-3W sold
separately).
Connect the control dock for iPod beforehand. (vpage 14
“iPod®”).
Playback
(vpage 40)
The following describes the procedure for playing Blu-ray disc/
DVD players.
Use the same procedure to play other components.
Settings
n Playing Blu-ray Disc/DVD Players (vpage 38)
n iPod® Playback (vpage 38)
n Listening to FM/AM Broadcasts (vpage 39)
n Listening to SIRIUS Satellite Radio Programs
iPod® Playback
Playing Blu-ray Disc / DVD Players
Connections
Getting Started
Playback
ENGLISH
Getting Started
Playing Components
4
Press
and hold it down for a 2 seconds or more to
select the display mode.
Connections
There are two modes for display the contents recorded on the
iPod.
Browse mode :Displayed on the TV screen.
Settings
Audio file
Playback
Playable
files
Video file
Active
buttons
nStopping playback temporarily
S
S
Sz2
nRepeat playback and shuffle
Sz1
Multi-Zone
S
S
iPod®
A
S
Remote Control
video file to be played.
Information
Playback starts.
to adjust the volume.
Troubleshooting
–80.0dB ~ 18.0dB
※The variable range differs according to the input signal and channel
Specifications
8 Select the desired surround mode.
9 Adjust the desired sound field effects.
(vpage 42 “Selecting the Surround Mode”)
(vpage 44 “Adjusting the sound Field Effects”)
Front
Press and hold
mode.
Front
“Remote iPod” is displayed on the AVR1910’s display.
• Use the RESTORER mode to expand the low and high frequency
components of compressed audio files and achieve a richer sound.
The default setting is “Mode3” (vpage 48).
• To check the name of the title, the artist or the
album when playing in browse mode, press
.
“TV Out” at the iPod’s “Slideshow Settings” or “Video Settings” must
be set to “On” in order to display the iPod’s photo data or videos on
the monitor. For details, see the iPod’s operating instructions.
Front
Front
NOTE
• Depending on the type of iPod and the software version, some
functions may not operate.
• DENON will accept no responsibility whatsoever for any loss of iPod
data.
iPod is a trademark of Apple Inc., registered in the U.S. and other
countries. The iPod may only be used to copy or play contents that
are not copyrighted or contents for which copying or playback is
legally permitted for your private use as an individual. Be sure to
comply with applicable copyright legislation.
Listening to FM/AM Broadcasts
Basic Operation
1
Set
2
Press
39
to set the Remote
the iPod’s screen, use ui
2 Watching
to select “Photos” or “Videos”.
Press
until the image you want to
3 view
is displayed.
“iPod Playback Mode” (vpage 35)
• Press
and set the AVR-1910’s power to the
standby mode before disconnecting the iPod.
Also switch the input source to one to which
the menu “iPod dock” is not assigned before
disconnecting the iPod.
• Photo and video data on the iPod can be viewed on the monitor. Only
for iPod equipped with slideshow or video functions. (When using an
ASD-1R or ASD-11R)
• Video may not be output, depending on the combination of ASD-1R
or ASD-11R and iPod.
1
playback
• The time (default : 30 sec) for which the onscreen display are displayed can be set at
menu “iPod Information” (vpage 31). Press
uio p to return to the original screen.
or p.
level setting.
.
During playback, press
or
.
Press again to resume playback.
Remote mode
Remote control
unit (AVR-1910)
GVariable rangeH – – –
or press
Browse mode
Use ui to select the menu, then
5 press
or p to select the music or
6
7 Use
During playback, either press and hold
During playback,
either press (to cue to
the current track) or
(to cue to the next
track).
z1:When using an ASD-11R, ASD-3N or ASD-3W control dock for
iPod.
z2:Video may not be output, depending on the combination of
ASD-1R or ASD-11R and iPod.
Front
Press
Viewing Still Pictures or Videos on the iPod®
nTo cue to the beginning of a track
Remote mode :Displayed on the iPod’s screen.
Display mode
nTo stop
to “MAIN/TV” and
to “MAIN”.
to select “TUNER”.
Front
Front
ENGLISH
to select “FM” or “AM”.
Tune
Rear
in the desired broadcast
station.
qTo tune in automatically (Auto Tuning)
Press
to light the “AUTO” indicator on the display, then use
wTo tune in manually (Manual Tuning)
Press
to turn off the display’s “AUTO” indicator, then use
Presetting Radio Stations (Preset Memory)
Tune in the broadcast station you want to preset.
Front
Press
.
Press
to select the block (A to G)
Press
Press
to select the preset number (1 to 8).
again to complete the setting.
•To preset other stations, repeat steps 1 to 5.
•Stations can be preset automatically at menu “Auto Preset” (vpage
36).
to select the desired preset channel (1
to 8).
To subscribe to SIRIUS, U.S. and Canadian customers can call 1-888539-SIRI (1-888-539-7474) or visit sirius.com (US) or siriuscanada.ca
(Canada).
SIRIUS XM Radio Legal
nDefault settings
Auto tuner presets
A1 ~ A8
87.5 / 89.1 / 98.1 / 107.9 / 90.1 / 90.1 / 90.1 /
90.1 MHz
B1 ~ B8
520 / 600 / 1000 / 1400 / 1500 / 1710 kHz,
90.1 / 90.1 MHz
C1 ~ C8
90.1 MHz
D1 ~ D8
90.1 MHz
E1 ~ E8
90.1 MHz
F1 ~ F8
90.1 MHz
G1 ~ G8
90.1 MHz
Listening to
Programs
SIRIUS, XM and all related marks and logos are trademarks of Sirius
XM Radio Inc. and its subsidiaries. All other marks and logos are the
property of their respective owners. All rights reserved. SIRIUS and
XM subscriptions sold separately. Taxes and a one-time activation fee
may apply. XM tuners and home docks or SIRIUS tuners (each sold
separately) are required to receive the SIRIUS or XM satellite radio
service. All programming and fees subject to change. It is prohibited to
copy, decompile, disassemble, reverse engineer, hack, manipulate or
otherwise make available any technology or software incorporated in
receivers compatible with the SIRIUS or XM Satellite Radio Systems.
Service not available in Alaska and Hawaii.
Basic Operation
SIRIUS
Satellite
Radio
About SIRIUS XM Radio
To listen to Satellite Radio, you’ll need to connect either a SIRIUS or XM
Satellite Radio tuner (sold separately) to your satellite-ready receiver.
Satellite Radio is available to residents of the US (except Alaska and
Hawaii) and Canada.
Satellite Radio delivers a variety of commercial-free music from
categories ranging from Pop, Rock, Country, R&B, Dance, Jazz,
Classical and many more plus coverage of all the top professional
and college sports including play by play games from select leagues
and teams. Additional programming includes expert sports talk,
uncensored entertainment, comedy, family programming, local traffic
and weather and news from your most trusted sources.
Whether you purchase a SIRIUS or XM tuner, you’ll need to activate
and subscribe to begin enjoying the service. Easy to follow installation
and setup instructions are provided with the satellite tuners. Whichever
service you choose, there are a variety of programming packages
available, including the option of adding “The Best of SIRIUS”
programming to your XM tuner or “The Best of XM” programming
to your SIRIUS tuner, enabling you to enjoy the most popular
programming among both services. The “Best of” packages are not
available to SIRIUS or XM Canada subscribers at this time.
1
Set
2
Press
3
Use
to “MAIN/TV” and
to “MAIN”.
to select “SIRIUS”.
Front
Front
to select the channel.
When the channel is tuned in, the name of
the track and artist are displayed.
Specifications
in which the station is to be preset.
Press
Troubleshooting
1
2
3
4
5
to select the memory block (A to G).
Information
Your favorite broadcast stations can be preset so that you can tune
them in easily. Up to 56 stations can be preset.
Remote Control
•When tuning in stations manually, press and hold
to change
frequencies continuously.
•The time (default : 30 sec) for which the on-screen display are
displayed can be set at “On-Screen Display” (vpage 31).
Press
Multi-Zone
•If the desired station cannot be tuned in with auto tuning, tune it in
manually.
1
2
To subscribe to XM, U.S. customers should visit xmradio.com or call
1-800-XMRADIO (1-800-967-2346); Canadian customers should visit
xmradio.ca or call XM Listener Care at 1-877-GETXMSR (1-877-4389677).
Playback
to select the station you want to hear.
Listening to Preset Stations
Settings
to select the station you want to hear.
NOTE
Preset stations are erased by overwriting them.
Connections
3
4
Press
Getting Started
Playing Components
Family friendly packages are also available to restrict channels featuring
content that may be inappropriate for children.
See overleaf
40
ENGLISH
Getting Started
Playing Components
Searching Categories
Front
•The channel switches continuously when
The strength of both the SIRIUS and terrestrial signals can be checked
at menu “Antenna Aiming” (vpage 37).
is pressed and held.
Connections
Settings
Playback
Multi-Zone
Remote Control
2
to select “SIRIUS”.
1
2
3
Tune in the broadcast channel you want to preset.
Press
Front
on the main unit until “SIGNAL” appears
on the display.
The display will switch as shown below,
depending on the reception conditions.
Information
Troubleshooting
Specifications
3
4
5
Status
Signal strength is excellent
Signal strength is good
Signal strength is weak
No signal
Press
Front
to select the block (A
preset.
4
5
Press
again to complete the setting.
NOTE
Preset channels are erased by overwriting them.
and select channel 0 (SR000).
Front
Listening to Preset Channels
1
2
Press
Press
to select the desired preset channel (1
to 8).
You can also operate via the main unit. In this case, perform the
following operations.
bWrite your own SIRIUS ID for storage use.
Sirius ID :
41
•“UPDATING” is displayed while the encoding code is being
updated.
•“SIRIUS UPDATING” is displayed when updating SIRIUS tuner
firmware.
•Refer to “Troubleshooting” – “SIRIUS Satellite Radio” regarding other
messages (vpage 64).
1
2
3 uio p
Tune to the channel you want to lock.
Press
“Code: [
for at least 3 seconds.
Front
]” is displayed.
When you enter the correct code, the corresponding channel is
locked.
4
Press
.
to select the memory block (A to G).
SR000 SiriusID
Sirius ID
o p to select the category,
then use ui to select the desired
channel.
Use
.
on the main unit until the channel you
want to check (example: “SR001”) is displayed.
************
Channel category
Parental Lock
to select the preset number (1 to 8).
To preset other channels, repeat steps 1 to 5.
Press
⇩
Pops
Enter the 4-digit lock code using
EXCELLENT” is shown on the display.
Channel No. and Sirius ID are alternately
shown on the display.
.
to G) in which the channel is to be
Press
Adjust the position of the antenna until “SIGNAL:
Press
2
Press
Display
EXCELLENT
GOOD
WEAK
NO SIGNAL
CAT :
Front
Your favorite broadcast channels can be preset so that you can tune
them in easily. Up to 56 channels can be preset.
Checking the SIRIUS Signal Strength and Radio ID
Press
Press o p.
Presetting Radio Channels (Preset Memory)
•The song title, artist name, composer name,
category and reception level can be checked
by pressing
on the main unit.
•The time (default : 30 sec) for which the onscreen display are displayed can be set at
menu “On-Screen Display” (vpage 31).
Press uio p to return to the original
screen.
1
1
•Press
, then turn
on the main
unit to select the preset radio channel.
•Channels under Parental Lock cannot be tuned in by performing
Tuning Up/Down or by category search.
•Channels stored in preset memory can be tuned in by the preset
channel select operation, even if Parental Lock is applied.
•When a channel to which Parental Lock is applied is being played,
Parental Lock for that channel is cancelled by performing Step2.
•See “Edit Lock Code” (vpage 37) for the method of changing
Parental Lock Code.
•You can also set “Parental Lock” from the menu (vpage 37).
ENGLISH
Operations During Playback
Selecting the Surround Mode
Select a surround mode to enjoy surround playback with your favorite sound field effects.
Turning Off the Sound Temporarily (Muting)
Front
.
q Playing sources according to the sources’ audio signal format/number of channels
(Standard Playback)
Operations
The sound from the speakers and pre-out connectors is automatically
cut.
Press
mode.
to select the surround
Rear
Select the mode for the source at “Mode” (vpage
44).
nDOLBY PLgx, DOLBY PLg
Cinema
:This mode is suited for movie sources.
Music
:This mode is suited for music sources.
Game
:This mode is suited for games.
Pro Logic :This is the Pro Logic playback mode. This can be
NOTE
.
Front B
Front A+B
NOTE
DOLBY PLgx,
DOLBY PLg
or
DOLBY PLgz
DTS NEO:6
Cinema
:This mode is suited for movie sources.
Music
:This mode is suited for music sources.
z
:The signals are decoded in DOLBY PLgx,
DOLBY PLg or DOLBY PLgz, for playback.
:The signals are decoded in DTS NEO:6 for
playback.
※The modes that can be selected depend on the input source
being played.
he “Cinema” and “Music” modes can also be set by pressing
T
or
.
z:DOLBY PLgx can be selected when surround back speakers are
being used.
Specifications
When you set to “Custom” with “Front Speaker Setup“ (vpage 27),
you cannot operate
.
When you select “DOLBY PLgz”, set “Amp
Assign” to “Front Height”.
nDTS NEO:6
Troubleshooting
Front A
n2channel sources
Information
Switching the front speakers
The surround modes that can be selected
differ according to the input source.
Remote Control
selected when playing with a DOLBY PLg decoder.
When this mode is selected, “DOLBY PL” is
displayed.
nMultichannel sources
• To prevent hearing loss, do not raise the volume level excessively
when using headphones.
• Unplug headphones when performing the Audyssey Auto Setup
procedure or other settings.
Press
1
2
This is the operation for playing 2-channel sources.
Multi-Zone
Plug the headphones into the PHONES jack on the main
unit.
Playing the source (vpage 38).
Playback
Listening with Headphones
3
Settings
• The sound is reduced to the level set at menu “Mute Level” (vpage
30).
• To cancel, press
again. Muting can also be canceled by adjusting
the master volume.
The selectable surround modes depend on the following:
•Format of the audio signals being input
•Number of channels of the audio signals being input
•The set amplifier assignment mode (vpage 25)
Connections
Press
Getting Started
Playing Components
See overleaf
42
ENGLISH
Getting Started
Selecting the Surround Mode
Displaying the currently playing surround mode
nSurround playback of multichannel sources
(Dolby Digital, DTS, etc.)
Connections
In the case of standard playback of multi channel sources, the
AVR-1910 recognizes the format of the multi-channel audio input
signal and automatically operates the appropriate decoder for
surround sound.
Settings
Input signal
Playback
Dolby Digital
(other than 2ch)/
Dolby Digital EX
Multi-Zone
Dolby
Digital
Dolby Digital Plus
(z1)
Dolby TrueHD (z1)
Remote Control
DTS (5.1ch)/
DTS-ES Discrete 6.1 /
DTS-ES Matrix 6.1 /
DTS 96/24
Information
DTS
DTS-HD (z1)
Troubleshooting
PCM
PCM
(multi ch)
Display
DOLBY DIGITAL
DOLBY DIGITAL EX
DOLBY DIGITAL+PLgx CINEMA
DOLBY DIGITAL+PLgx MUSIC
DOLBY DIGITAL+PLgz
DOLBY DIGITAL++PLgx C
DOLBY DIGITAL++PLgx M
DOLBY DIGITAL++PLgz
DOLBY TrueHD
DOLBY HD+EX
DOLBY HD+PLgx CINEMA
DOLBY HD+PLgx MUSIC
DOLBY HD+PLgz
DTS SURROUND
DTS+PLgx CINEMA
DTS+PLgx MUSIC
DTS+PLgz
DTS+NEO:6
DTS ES MTRX6.1 (z2)
DTS ES DSCRT6.1 (z3)
DTS 96/24 (z4)
DTS-HD HI RES
DTS-HD MSTR
DTS-HD+NEO:6
DTS-HD+PLgx CINEMA
DTS-HD+PLgx MUSIC
DTS-HD+PLgz
MULTI CH IN
MULTI IN+PLgx CINEMA
MULTI IN+PLgx MUSIC
MULTI IN+PLgz
MULTI CH IN 7.1
Specifications
z1:When a signal is input, the HD AUDIO indicator lights.
z2:This is displayed when the input signal is “DTS-ES Matrix 6.1”
and the AVR-1910’s “AFDM” setting (vpage 45) is set to “ON”.
z3:This is displayed when the input signal is “DTS-ES Discrete
6.1”.
z4:This is displayed when the input signal is “DTS 96/24”.
43
w Playing in a DENON original surround
mode
The desired mode according to the program source and viewing
situation can be selected from among 7 DENON original surround
modes.
1
Select the input source by pressing
and play the source (vpage
38).
Front
Press
mode.
2
to select the Surround
Rear
5CH/7CH STEREO :This mode is for enjoying stereo sound from all
speakers.
ROCK ARENA
:This mode is for enjoying the atmosphere of a
live concert in an arena.
JAZZ CLUB
:This mode is for enjoying the atmosphere of a
live concert in a jazz club.
MONO MOVIE :This mode is for playing monaural movie
sources with surround sound. z1
VIDEO GAME
:This mode is suited for achieving surround
sound with video games.
MATRIX
:This mode lets you add a sense of expansion
to stereo music sources.
VIRTUAL
:This mode is for enjoying surround effects
using only the front speakers or headphones.
z1:When playing sources recorded in monaural in the MONO
MOVIE mode, the sound will be off balance with a single
channel (left or right), so input to both channels.
Depending on the program source being played, it may not be possible
to achieve a satisfactory surround effect. In this case, try other modes
to achieve a sound field suited to your tastes.
NOTE
When the input signal is DOLBY TrueHD, DOLBY DIGITAL Plus,DTSHD
you cannot select DENON original surround mode.
e Direct Playback
In this mode the signals bypass the tone adjustment circuitry for
high quality sound.
The sound is output to the same channels as the input signal.
1
Select the input source by pressing
and play the source (vpage
38).
2
Press
Front
Rear
to select the “DIRECT”.
Displaying the currently playing surround mode
Input signal
Analog signal /
PCM (2ch) /
Dolby Digital source /
DTS source /
Other 2-channel digital signals
PCM (multi ch)
Display
DIRECT
MULTI CH DIRECT
M DIRECT + PLgx CINEMA
M DIRECT + PLgx MUSIC
M DIRECT + PLgz
M DIRECT 7.1
ENGLISH
Adjusting the Sound Field Effects (Parameter)
r Stereo Playback
1
Press
NOTE
Some of the setting items cannot be set while playback is stopped. Set these items during playback.
Adjusting the sound field effects (Surround Parameter)
Default settings are underlined.
Rear
toselectthe“STEREO”.
Setting items
Mode
t Playing the Pure Direct mode
Press
.
Rear
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
Specifications
NOTE
When in the PURE DIRECT mode, the on-screen display is not
displayed and the display on the main unit is turned off.
Troubleshooting
• To cancel, press
again.
• The channel level and surround parameters in the PURE DIRECT
mode are the same as in the DIRECT mode.
• The “Music” mode is also effective for movie sources including a
lot of stereo music.
• The “Cinema” and “Music” modes can also be set by pressing
or
.
OFF : “Cinema EQ” is not used.
Cinema EQ
Soften the treble range of ON : “Cinema EQ” is used.
movie sound tracks for better
understanding.
Dynamic
Range Low/Mid/High : These set the compression level.
Compression (D.Comp) OFF : Turn dynamic range compression off.
Compress dynamic range
The “D.Comp” indicator lights when playing DTS source that supports
(difference between loud
the “D.Comp” function.
and soft sounds).
Dynamic Range Control Auto : Dynamic range compression of Dolby TrueHD sources turns on and
off automatically.
(DRC)
Low/Mid/High : These set the compression level.
Compress dynamic range
OFF : Turn dynamic range compression off.
–10dB ~ 0dB
LFE
Adjust the low-frequency
For proper playback of the different program sources, we recommend
effects level (LFE).
setting to the values below.
• Dolby Digital sources : “0dB”
• DTS movie sources :
“0dB”
• DTS music sources :
“–10dB”
Information
2
Front
Cinema : This is the mode for cinema source.
Music : This is the mode for music source.
Remote Control
Select the input source by pressing
andplaythesource(vpage
38).
Cinema : This is the mode for cinema source.
Music : This is the mode for music source.
Game : This is the mode for game source.
ProLogic : Dolby Pro Logic playback mode (PLg mode only). (This is
the mode for 4-channel playback (front L, front R, center, surround
(MONO).)
n In the DTS NEO:6 mode
This is the mode that recreates the original sound most faithfully,
providing extremely high quality sound.
1
n In the PLgx, PLg or PLgz mode
Multi-Zone
Set the play mode for
playing 2-channel sources in
surround.
Setting contents
Playback
2
Front
Settings
Select the input source by pressing
andplaythesource(vpage
38).
The sound being played in the surround mode can be adjusted to your liking.
The items (parameters) that can be adjusted depend on the signal being input and the currently set surround
mode. For details on the adjustable parameters, see “Surround Modes and Parameters” (vpage 58).
Connections
This is the mode for playing in stereo. The tone can be adjusted.
Sound is output from the front left and right speakers and
subwoofer.
Getting Started
Selecting the Surround Mode
ENGLISH
Getting Started
Adjusting the Sound Field Effect (Parameter)
Setting items
Center Image
Setting contents
Setting items
Setting contents
AFDM (Auto Flag Detect ON : Set.
OFF : Do not set.
Mode)
0.0 ~ 1.0 (0.3)
Connections
Assign center channel signal
to front left and right channels
for wider sound.
Panorama
Settings
Playback
Multi-Zone
Remote Control
Information
Troubleshooting
ON : Set.
Assign front L/R signal also OFF : Do not set.
to surround channels, for
wider sound.
0 ~ 6 (3)
Dimension
Shift sound image center
to front or rear, to adjust
playback balance.
0 ~ 7 (3)
Center Width
Assign center channel signal
to front left and right channels
for wider sound.
0ms ~ 300ms (30ms)
Delay Time
Adjust delay time to control
sound stage size.
1 ~ 15 (10)
Effect Level
Adjust the strength of the
Set to a lower level if the positioning and sense of phase of the
surround effect.
surround signals seems unnatural.
Small : Simulate acoustics of a small room.
Room Size
Determine size of acoustic Medium small : Simulate acoustics of a medium-small room.
Medium : Simulate acoustics of a medium room.
environment.
Medium large : Simulate acoustics of a medium-large room.
NOTE
Large : Simulate acoustics of a large room.
“Room Size” does not
indicate the size of the room
in which sources are played.
Detects the source’s surround
back channel signal and sets
the optimum surround mode
automatically.
Surround Back
Sets the method of
generating of the surround
back channel.
nFor 2-channel sources
ON : The surround back channel is used.
OFF : No signal is played from the surround back channels.
nFor multi channel sources
Set this to set the method of generating of the surround back channel
for sources that do not include surround back signals and when you
do not want to play the surround back signals included in the source.
Check the audio signals of the source being played before making this
setting.
OFF : No signal is played from the surround back channels.
MTRX ON : Generate and play the surround back signals from the
surround channel signals.
PLgx CINEMAz1 : Generate and play the surround back signals by
decoding the signals in the “Dolby Pro Logic gx Cinema” mode.
PLgx MUSICz2 : Generate and play the surround back signals by
decoding the signals in the “Dolby Pro Logic gx Music” mode.
ES MTRX : Generate and play the surround back signals from the
surround channel signals of the DTS source.
ES DSCRTz3 : Play the surround back signals included in the 6.1channel DTS source.
DSCRT ONz3 : Play the surround back signals included in the 7.1channel source.
z1 : This can be selected when “S.Back” in the “Speaker Config.”
settings (vpage 26) is set to “2sp”.
z2 : This can be selected when “S.Back” in the “Speaker Config.”
settings (vpage 26) is set to “2sp” or “1sp”.
z3 : When “AFDM” is set to “ON”, the surround back channel is played
with the AFDM function. When selected while “AFDM” is set to
“OFF”, the source’s surround back signals are played.
Specifications
This can also be set by pressing
.
NOTE
This is valid when the “Amp Assign” setting (vpage 25) is set to “7.1channel surround back” or “6.1-channel surround back”, and when the
“S.Back” setting (vpage 26) is set to “Large” or “Small”.
45
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
Setting items
Setting contents
Making the MultEQ, Dynamic EQ and Dynamic Volume
settings (Audyssey Settings)
Front Height
Default settings are underlined.
Subwoofer ATT
ON : The input from the subwoofer channel is attenuated.
Attenuate subwoofer level OFF : The input from the subwoofer channel is not attenuated. Usually use
in this mode.
when using EXT. IN mode.
Setting contents
Bass
–6dB ~ +6dB (0dB)
Adjusts the low frequencies.
Treble
–6dB ~ +6dB (0dB)
Adjusts
the
frequencies.
high
This can be set when
“Tone Control” is set to
“ON”.
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
46
Specifications
This can be set when
“Tone Control” is set to
“ON”.
Troubleshooting
ON : Allow tone adjustment (treble, bass).
Sets the tone control function OFF : Playback without tone adjustment.
ON and OFF.
The tone cannot be adjusted when in the DIRECT mode.
This can be set when
“Dynamic EQ” (vpage
47) is set to “OFF”.
Audyssey : Optimize frequency response of all speakers.
Corrects
the
frequency Audyssey Byp.L/R : Optimize frequency response of speakers except
response of the different front L and R speakers.
Audyssey Flat : Optimize frequency response of all speakers to flat
speakers.
response.
NOTE
Manual : Apply frequency response set with “Manual EQ” (vpage 47).
•“MultEQ” and “Manual OFF : The “MultEQ” equalizer cannot be used.
EQ” settings for which
• When “Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is
“Not Used” has been set at
selected, “
” lights.
“EQ Customize” (vpage
29) cannot be selected.
• After running Audyssey Auto Setup, if the Speaker Configuration,
•When using headphones,
Distance, Channel Level, and Crossover Frequency have changed
“MultEQ” is set to “OFF”.
without increasing the number of speakers measured, only “
” lights.
•This can also be set by pressing
.
Information
Tone Control
Setting contents
MultEQ
Remote Control
Setting items
Setting items
Multi-Zone
Default settings are underlined.
Playback
Adjusting the tone (Tone Control)
NOTE
If the speaker settings are changed after the “Audyssey Auto Setup” procedure is performed,
“MultEQ”, “Dynamic EQ” and “Dynamic Volume” functions cannot be selected and “Run Audyssey”
is displayed.
If this happens, either perform the “Audyssey Auto Setup” procedure again, or perform the “Restore”
operation (vpage 24) to restore the settings to as they were after the “Audyssey Auto Setup”
procedure was performed.
Settings
Set this to “ON” if the subwoofer channel level seems too high when
playing audio signal.
ON : The subwoofer is used.
Subwoofer
Turn subwoofer output on OFF : The subwoofer is not used.
and off.
Yes : Reset to the defaults.
Default
Restores all the surround No : Do not reset to the defaults.
parameter settings to their
defaults.
•When the “Audyssey Auto Setup” (vpage 20) procedure is performed, the “MultEQ”, “Dynamic
EQ” and “Dynamic Volume” functions are enabled.
•Operating conditions for each function
•Dynamic EQ :
MultEQ
When “MultEQ” is set to “ON”
Dynamic EQ
•Dynamic Volume :
When “Dynamic EQ” is set to “ON”
Dynamic Volume
•Setting :
Setting
When “Dynamic Volume” is set to “ON”
Connections
ON : Use the front height channel.
Set whether or not to use OFF : Do not use the front height channel.
the front height channel.
This can also be set by pressing
.
Getting Started
Adjusting the Sound Field Effect (Parameter)
ENGLISH
Getting Started
Adjusting the Sound Field Effect (Parameter)
Setting items
Setting contents
Setting items
Dynamic EQ
Connections
ON : Use Dynamic EQ function.
Audyssey Dynamic EQ solves OFF : Do not use Dynamic EQ function.
the problem of deteriorating
•W
hen set to “ON”, “
” is displayed.
sound quality as volume is
•
W
hen
“MultEQ”
is
set
to
“OFF”
, “Dynamic EQ” is automatically set
decreased by taking into
to “OFF”
account human perception
•This can also be set by pressing
.
and room acoustics.
Settings
Dynamic EQ : ON/Volume : OFF
Playback
This can be set when the
“MultEQ” (vpage 46)
is set to anything other
than “OFF”.
“Red”
“Green”
Setting
Set Dynamic Volume effect.
This can be set when
“Dynamic EQ” (vpage
47) is set to “ON”.
Setting contents
Day : Low setting provides the least adjustments to the loudest and
softest of sounds.
Evening : Middle setting prevents loud and soft sounds from being much
louder and softer respectively than average sounds.
Midnight : High setting affects volume the most, causing all sounds to be
of equal loudness.
Dynamic EQ / Volume : OFF
Adjust tonal quality for each speaker using graphic equalizer
(Manual EQ)
“Off”
“OFF”
Default settings are underlined.
NOTE
Multi-Zone
“Tone Control” is set to “OFF” when “Dynamic EQ” is set to “ON”.
Reference Level Offset : Audyssey Dynamic EQ takes the standard film
mixing level of 85 dB SPL during –20 dB FS input as its reference level.
However, since standardization is lacking outside the film industry, the
reference level of media contents may not be appropriate. In order to
view such contents, Reference Level Offset of Dynamic EQ has available
offsets of 5 dB, 10 dB and 15 dB.
• 0dB : Suitable for viewing movies.
• 5dB : Suitable for listening to classical music and other content mixed
at a high level.
• 10dB : Suitable for listening to jazz and other audio sources with a wide
dynamic range. Also suitable for viewing TV.
• 15dB : Suitable for listening to pop, rock music and other content with an
extremely wide dynamic range.
Remote Control
Information
Troubleshooting
Specifications
etting is enabled when “Dynamic EQ” is “ON” .
S
ON : Use Dynamic Volume. The Dynamic Volume effect will be at the level
Audyssey Dynamic Volume of the “Setting” (vpage 47)
solves the problem of OFF : Do not use Dynamic Volume.
large variations in volume
•When set to “ON”, “
” is displayed.
level between television
•When “MultEQ” is set to “OFF”, “Dynamic Volume” is automatically
programs, commercials, and
set to “OFF”.
between the soft and loud
•This can also be set by pressing
.
passages of movies.
Dynamic EQ / Volume : ON
Dynamic EQ : ON / Volume : OFF
Dynamic Volume
This can be set when
“Dynamic EQ” (vpage
47) is set to “ON”.
47
Remote control
operation buttons
“Green”
“Green”
Displaying the menu
: Cancel the menu
Setting items
Setting contents
Adjust CH
1.Select speaker adjustment method.
All CH : Adjust tonal quality for all speakers together.
Adjust the tonal quality of
L/R CH : Adjust tonal quality for each L/R speaker pair.
the individual speakers.
Each CH : Adjust tonal quality for each speaker separately.
2.Select the frequency band to be adjusted.
63Hz / 125Hz / 250Hz / 500Hz / 1kHz / 2kHz / 4kHz / 8kHz /
16kHz
bWhen “L/R CH” or “Each CH” is selected, select the speaker to be
adjusted.
3.Adjust the level.
–20.0dB ~ +6.0dB (0dB)
Yes : Copy.
Base Curve Copy
Copy the MultEQ “Audyssey No : Do not copy.
Flat” correction curve.
“Base Curve Copy” is displayed after the Audyssey Auto Setup
procedure has been performed.
Yes : Reset to the defaults.
Default
Reset the “Manual EQ” No : Do not reset to the defaults.
settings to their defaults.
“Red”
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
ENGLISH
Restoring compressed audio to nearly pre-compressed
conditions for playback (RESTORER)
Default settings are underlined.
Mode 1
(RESTORER 64)
Mode 2
(RESTORER 96)
Mode 3
(RESTORER HQ)
Setting contents
0ms ~ 200ms
Remote control
operation buttons
Displaying the menu
: Cancel the menu
: Moves the cursor (Up/Down/Left/Right)
: Decision the setting
: Return to previous menu
8
Specifications
• If you wish to adjust the “Audio Delay” while playing HDMI or component video signals, press u
to set “OSD” to “OFF”.This way the audio delay can be adjusted while watching the picture. (Press
the u again. The display switches to the display of the menu screen only.)
• This cannot be adjusted when playing in the EXT. IN, DIRECT or STEREO mode (with “Front
Speaker” set to “Large”, “Tone Control” to “OFF” and “MultEQ” and “RESTORER” to “OFF”).
• When the Auto Lipsync Correction function is operating, you can set within the range 0 ~ 100 ms.
• Store “Audio Delay” for each input source.
Troubleshooting
Default settings are underlined.
Information
Adjusting the audio delay time while watching the picture
(Audio Delay)
You can also display current status on the main unit’s display each time you
press
on the main unit.
ZONE2
• POWER/ Select Source/ Master Volume
Surround Mode : The currently set surround mode is displayed.
Audio Input Signal
Shows information about Signal : The input signal type is displayed.
fs : The input signal’s sampling frequency is displayed.
audio input signals.
Format : The number of channels in the input signal (front, surround, LFE)
is displayed.
Offset : The dialogue normalization correction value is displayed.
Flag : This is displayed when inputting signals including a surround back
channel. “MATRIX” is displayed with Dolby Digital EX and DTS-ES Matrix
signals, “DISCRETE” with DTS-ES Discrete signals.
HDMI Signal Information
HDMI Information
Shows information about • Resolution / Color Space / Pixel Depth
HDMI input signals and HDMI Monitor Information
monitor.
• Interface / Suport Resolution
Analog/PCM / Digital 2ch / Digital 5.1ch / Multi CH
Auto Surround Mode
Shows information about
auto
surround
mode
settings.
Quick Select 1 / Quick Select 2 / Quick Select 3
Quick Select
Shows information about • Name / Input Source / Video Select / Volume Level / MultEQ /
Dynamic EQ / Dynamic Vol / Front SP / Analog/PCM / Digital 2ch /
quick select settings.
Digital 5.1ch / Multi CH
ZONE2 Quick Select
Quick Select 1 Source / Quick Select 1 Volume / Quick Select 1 Name
Quick Select 2 Source / Quick Select 2 Volume / Quick Select 2 Name
Quick Select 3 Source / Quick Select 3 Volume / Quick Select 3 Name
A1~G8
Preset Channel
Shows information about • TUNER / SIRIUS
preset channels.
Remote Control
OFF
Select Source / Surround Mode / Input Mode / Decode Mode / HDMI
about / Digital / Component / iPod Dock / Video Select / Source Level / i/p
Scaler / Resolution / Progressive Mode / Aspect
Multi-Zone
• The default setting for “iPod” is “Mode3”. All others are set to “OFF”.
• When set to something other than “OFF”, “
” is displayed.
• This can also be set by pressing
during playback.
Shows information
current settings.
Playback
Status
Setting contents
Settings
Setting contents
OFF : Do not use RESTORER.
Mode1 (RESTORER 64) : Optimized mode for compressed sources with very weak highs.
Mode2 (RESTORER 96) : Apply suitable bass and treble boost for all compressed sources.
Mode3 (RESTORER HQ) : Optimized mode for compressed sources with normal highs.
Setting items
Connections
• Such compressed audio formats as MP3, WMA (Windows Media Audio) and MPEG-4 AAC reduce the
amount of data by eliminating signal components that are hard for the human ear to hear. The RESTORER
function generates the signals eliminated upon compression, restoring the sound to conditions near
those of the original sound before compression. It also corrects the sense of volume of the bass to obtain
richer sound with compressed audio signals.
• This can be set with analog signals or when a PCM signal (fs = 44.1/48 kHz) is input.
Checking the Status (Information)
Getting Started
Adjusting the Sound Field Effect (Parameter)
ENGLISH
Getting Started
Convenient functions
HDMI Control Function
Connections
When you make an HDMI connection with a TV or player
compatible with AVR-1910 and HDMI control functions, you can
perform the following operations by setting the HDMI control
function of each device.
Settings
n AVR-1910 power off can be linked to the TV power
Playback
output setup operation, you can switch the amp power
on.
off step
zWhen you set “Output audio from amp” in the TV audio
n You can switch audio output devices with a TV
Multi-Zone
operation
n You can adjust AVR-1910 volume in the TV volume
adjustment operation
Remote Control
n You can switch AVR-1910 input source through
linkage to TV input switching
n When playing the player, the AVR-1910 input
function switches to the function of that player
Information
• To play the TV’s sound on the AVR-1910, make optical digital
connections (vpage 13 “Connecting the TV”).
• To use this function, set “HDMI Control” (vpage 28) to “ON”.
Troubleshooting
NOTE
Specifications
• When you power off AVR-1910, the HDMI control function does not
operate.
• Some functions may not operate depending on the connected
TV or player. Check the owner’s manual of each device for details
beforehand.
• When “HDMI Control” is set to “ON”, it is not possible to assign an
HDMI terminal to “TV” at “HDMI” (vpage 28).
• When “HDMI Control” (vpage 28) is set to “ON”, power is supplied
constantly to the AC outlet (UNSWITCHED).
1
2
Turnthepoweronforalltheequipmentconnectedby
HDMIcable.
Set the HDMI control function for all equipment
connectedbyHDMIcable.
Set “HDMI Control” (vpage 28) to “ON“.
b Please refer to the owner’s manual as regards setting of connected
devices.
b Carry out Steps 1 and 2 should any of the equipment be
unplugged.
3
4
5
SwitchthetelevisioninputtotheHDMIconnectedto
theAVR-1910.
SwitchtheAVR-1910inputtotheHDMIinputsource
andcheckifthepicturefromtheplayerisok.
WhenyouturntheTV’spowertostandby,checkthat
thepoweroftheAVR-1910andplayeralsogoeson
standby.
If the HDMI control function does not operate properly, check the
following points.
• Is the TV or player compatible with the HDMI control function?
• Is the AVR-1910 properly set?
• Is “HDMI Control” (vpage 28) set to “ON”?
• Is “Power Off Control” (vpage 28) set to “ON”?
• Are the HDMI control function settings of all equipment correct?
NOTE
Should any of the operations below be performed, the interlocking
function may be reset, in which case, repeat step’s 1 and 2.
• Menu “HDMI” (vpage 28) setting has changed.
• There is a change to the connection between the equipment and the
HDMI, or an increase in equipment.
Setting the power to standby
after a certain amount of time
(Sleep Timer Function)
This function allows you to automatically set the power to standby
after the set amount of time has passed.
When the sleep timer turns the power off in the MAIN ZONE, the
power also turns off in the ZONE2.
Press
anddisplaythetimeyouwanttoset.
The “SLEEP” indicator on the display lights.
• The time switches as shown below each time
pressed.
Sleep:OFF
Sleep:120min
Sleep:30min
is
Sleep:90min
Sleep:60min
• The time display turns off after about 5 seconds, and the
setting is activated.
• Once the set time has passed, the power is automatically set
to standby.
n To cancel the sleep timer
Press
to set “OFF”.
• The “SLEEP” indicator on the display turns
off.
Rear
ENGLISH
Saving frequently used settings
(Quick Select Function)
You can adjust the channel level either according to the playback
sources or to suit your taste, as described below.
1
Press
.
Channel Volume
0.0dB
0.0dB
0.0dB
0.0dB
SR
SBR
SBL
SL
0.0dB
0.0dB
0.0dB
0.0dB
[
Front
Press ui to select the speaker.
The speaker that can be set switches each
time one of the buttons is pressed.
Press o p to adjust the volume.
bIn the case of a subwoofer, reducing the volume when it is at
“–12 dB” will change the setting to “OFF” (none).
Saving the settings
1
MAIN ZONE settings
Saving the settings
1 Set the items below to the settings you want to save.
q Input source (vpage 38)
w Input Mode (vpage 34)
e Surround Mode (vpage 42)
r Audyssey Settings (MultEQ, Dynamic EQ, Dynamic
Volume) (vpage 46)
t Front Speaker Setup (vpage 27)
y Volume setting (vpage 38)
Press and hold the desired
2 appears
on the display.
The current settings will be memorized.
until “Memory”
Front
This function lets you adjust (fade) the sound from all the front (Front
speaker / center speaker / Front Height speaker) or rear (Surround speaker /
Surround Back speaker) speakers at once.
Press o p to adjust the volume of the speakers.
Volume
–40 dB
–40 dB
–40 dB
Personal Memory Plus Function
This function sets the settings (input mode, surround mode, MultEQ,
Dynamic EQ, Dynamic Volume, audio delay etc.) last selected for the
individual input sources.
This stores the settings as they were directly before the standby mode
was set.
When the power is turned back on, the settings are restored to as they
were directly before the standby mode was set.
Backup Memory
Calling the settings out
Press the
at which the
settings you want to call out are saved.
Various memory functions
Front
The various settings are backed up for about 1 week, even if the power
is turned off or the power cord is disconnected.
NOTE
•The fader function does not affect the subwoofer.
•The fader can be adjusted until the volume of the speaker adjusted
to the lowest value is –12 dB.
Input sources stored with the quick select function cannot be selected
if they have been deleted at menu “Source Delete” (vpage 30). In
this case, store them again.
50
Specifications
1
2
or i to select “Fader”, then select the item
to be adjusting using o or p.
Use
Input Source
DVD
SAT/CBL
VCR/iPod
Perform steps 1 and 2 under “MAIN ZONE
settings”.
Last Function Memory
GQuick Select DefaultsH
Quick Select 1
Quick Select 2
Quick Select 3
2
Troubleshooting
Adjusting the volume of groups of speakers
(Fader Function)
device selector switches as
shown on right.
Information
If headphones are plugged in, the headphones settings screen
appears.
Set the remote control unit’s
Remote Control
3
It is also possible to save three settings for ZONE2.
Multi-Zone
2
]:CH Sel.
ZONE2 settings
Playback
Fader
FRONT : REAR
•Three sets of settings can be saved.
“Quick Select Name” (vpage 31).
Settings
FL
C
FR
SW
Connections
Adjust the volume of the different speakers
This function allows you to save all the settings shown in step
1. When frequently used settings are saved, they can easily be
set again the next time you want to use them. This function also
allows you to always enjoy the same playback environment.
nNaming Quick Select settings
Getting Started
Adjust the volume of the
different speakers
ENGLISH
Getting Started
Playing 2-Channel Sound in ZONE2 (multizone function)
Connections
2-channel sound can be played in rooms other than the MAIN
ZONE where multichannel sound is played.
There are two methods to do this, as described below. Choose
one of the methods.
qZONE2 playback by speaker output
wZONE2 playback by audio output (PRE OUT) (using an
external amplifier))
Settings
Playback
q ZONE2 playback by speaker
output
w ZONE2 playback by audio
output
The audio signals connected to the AVR-1910’s ZONE2 output terminals
(ZONE2 OUT) are output to the ZONE2’s amplifier and played with that
amplifier.
Connection (ZONE2)
Playback
The operation is the same for “q ZONE2 playback by speaker
output” and “w ZONE2 playback by audio output”.
1
Set the remote control unit’s
“device selector switches” as
shown on right.
2
Turn on the AVR-1910’s power.
MAIN ZONE
(vpage 17 “Turning the Power On”)
With the Amp Assign function, Zone 2 audio signals are output from
the AVR-1910's SURR BACK/AMP ASSIGN terminals.
Multi-Zone
3
Press
Preparations
Rear
R
AVR-1910
L
Remote Control
Connecting and setting the speakers
to turn on the ZONE2 power.
When the power turns on, the “
display.
” indicator lights on the
bThe power can be turned on by pressing the one of
while in the standby mode.
n Connecting the speakers
4
Use the input source selector to choose the input
ZONE2
R
Information
(L)
w
(R)
q
w
L
"69
*/
q
source.
The selected input source is shown on the display.
NOTE
Troubleshooting
When “SOURCE” is selected for the input source, the sound being
played in the MAIN ZONE is played. No sound is output if a digital
audio input source is being played in the MAIN ZONE.
Adjusting the volume (for “q ZONE2 playback by
speaker output”)
n Necessary settings
Specifications
• Set the AMP ASSIGN mode to “ZONE2”.
“AMP Assign” (vpage 25)
• Perform the settings at “ZONE2 Setup”.
“Making the ZONE2 settings” (vpage 30)
Use
• Adjust the volume on the connected amplifier.
• Also be sure to read the operating instructions of the connected
devices.
NOTE
•We recommend using high quality pin-plug cables for audio
connections in order to prevent noise.
•It is not possible to play the digital audio signals input from the
HDMI, COAXIAL or OPTICAL terminals in ZONE2. Play using analog
connections (in stereo).
51
to adjust the volume.
GVariable rangeH – – –
–80dB(1) ~ –40dB(41) ~ +18dB(99)
b The volume can be adjusted up to the level set at “Vol. Limit”
(vpage 30).
b The volume display is the display set at “Volume Display”
(vpage 30).
or “w ZONE2 playback by audio output”, adjust the volume on the
F
connected amplifier.
ENGLISH
Registering Preset Codes
Operating Registered Devices
MAIN/TV : To register a TV
DEVICE : To operate a Blu-ray disc player, DVD player,
to the component to be registered.
TV
Digital video recorder, video deck, satellite
receiver, cable TV or CD player
2 Set
: TV
TV
: TV
DVD/HDP : DVD player or Blu-ray disc player
DVR/VCR : DVD recorder or video deck
DVR/VCR : Digital video recorder or video deck
SAT/CBL : Satellite receiver or cable TV
SAT/CBL : Satellite receiver or cable TV
3
: CD player
at the same
Rear
The indicator starts flashing.
Depending on the model and year of manufacture, this function cannot
be used for some models, even if they are of makes listed in the list
of preset codes.
uio p
ENTER
Cursor
Enter
3
Pause
Press and
hold
b For details, refer to the component’s operating instructions.
NOTE
Auto search
(cue)
Front
SEARCH
RETURN
Once
Page search
Browse/Remote mode switching
mode switching
z2
Return
z1 : This operation is possible when using a
DENON ASD-3N or ASD-3W Control Dock
for iPod.
z2 : This operation is possible when using a
DENON ASD-1R or ASD-11R Control Dock
for iPod.
Specifications
store the codes of another component in the
5 Tomemory,
repeat steps 1 to 4.
Operate the component.
8 9
Troubleshooting
4
Press
~
and input the 3digit number of the brand of the
component to be preset. The numbers
are shown in the Preset Code Table
(vEnd of this manual).
and
: CD player
Play / Pause
Stop
MEMORYz1
Page up/down z1
Information
3
Press
time.
CD
1
2
MEMORY
TU/PAGE
Remote Control
DVD/HDP : DVD player or Blu-ray disc player
CD
DEVICE SELECT
to the component you want to operate.
Front
MAIN/TV : To operate the TV
DEVICE : To operate a Blu-ray disc player, DVD player,
Multi-Zone
2 Set
iPod
Playback
Digital video recorder, video deck, satellite
receiver, cable TV or CD player
1
.
Settings
1
.
Switch
Connections
DENON and other makes of components can be operated by setting
the preset memory.
Switch
Getting Started
Operating the Connected Devices by Remote Control Unit
•Some manufacturers use more than one type of remote control code.
Refer to the included list of preset codes to change the number and
verify correct operation.
•VDP (Video Disc Player) can be preset when
is set to “DVD/
HDP”.
•The preset memory can be set for one component only among the
following: DVD/HDP, DVR/VCR and SAT/CABLE.
52
ENGLISH
Getting Started
Operating Registered Devices
TV
Blu-ray Disc / DVD Player
Front
Connections
Settings
Playback
6 7
Multi-Zone
CH + –
TV INPUT
VOLUME df
Remote Control
Front
MUTE
MENU
uio p
ENTER
SETUP
RETURN
DEVICE SELECT
Power on / Standby
Playz
Pausez
Stopz
Manual search z
POWER OFF
ON/SOURCE
1
2
SHIFT, 3
(fast-reverse / fast-forward)
Channelz
SKIP +
Switching the input
d : TV Volume (+)
f : TV Volume (–)
TV MUTE
Calling out the menus
Cursor operation
Enter setting
Setup
Return
6 7
Front
Information
Channels
0 ~ 9, +10
Troubleshooting
q
Default setting
(Preset code)
Special Remarks
Power off
Power on or Power on / Standby
Play
Stop
Pause
BD Player
DVD Player
–
ON/SOURCE
1
2
SHIFT, 3
6 7
CH + –
MENU
uio p
ENTER
SETUP
RETURN
Disc skip
Manual search
(fast-reverse / fast-forward)
Auto search (cue)
Calling out the menus
Cursor operation
Enter setting
Setup
Return
Front
Calling out the top menus
Number input / Track selection
BD Player
DVD Player
DENON DENON (121)
(111)*
q, w
Specifications
Rear
Rear
Power on / Standby
Play
Stop
Pause
Manual search
(fast-reverse / fast-forward)
Switch channels (+, –)
Calling out the menus
Cursor operation
Enter setting
Setup
Return
Rear
0 ~ 9, +10
Default setting
(Preset code)
Special Remarks
* : The initial setting of Preset code is 111 (DVD Player).
【Special Remarks】
q Only one device can be set in the preset memory for each mode.
When a new preset code is registered, the existing code is automatically erased.
w For some brands, the DVD remote control buttons may have different function names.
Check beforehand.
53
DEVICE SELECT
Rear
HITACHI (014)
z : When the punch through function
(vpage 54) is set, this functions as the
button for the device for which punch
through is set.
Rear
8 9
MENU
uio p
ENTER
SETUP
RETURN
SOURCE SELECT /
TOP MENU
Rear
1 ~ 12
Default setting
(Preset code)
Special Remarks
Front
Front
DEVICE SELECT
ON/SOURCE
1
3
2
Digital Video Recorder / Video Deck
Channels
HITACHI (008)
q, w
ENGLISH
Satellite receiver/Cable TV
CD Player
Front
Front
Rear
0 ~ 9, +10
Special Remarks
Front
0 ~ 9, +10
Number input / Track selection
Default setting
(Preset code)
DENON (111)
Special Remarks
q
: Assigning TV buttons to operate other devices
SAT/CBL : Assigning satellite receiver or cable TV buttons to
3
.
TV
operate other devices
Press
and
at the same time.
Rear
The indicator starts flashing.
4
Refer to the table below and input the number
corresponding to the device to be assigned.
ABC (009)
–
2 Switch
Rear
Channels
Satellite
Cable TV
Receiver
operate other devices
q
Device to be assigned
z : When the punch through function
(vpage 54) is set, this functions as the
button for the device for which punch
through is set.
Numbers
Troubleshooting
iPod, Tuner
CD Player
Blu-ray Disc Player / DVD Player
Specifications
DVD Recorder, Video Deck
No setting
Rear
Rear
【Special Remarks】
q Only one device can be set in the preset memory for each mode.
When a new preset code is registered, the existing code is automatically erased.
w For some brands, the DVD remote control buttons may have different function names.
Check beforehand.
Information
Default setting
(Preset code)
8 9
.
MAIN/TV : Assigning TV buttons to operate other devices
DEVICE : Assigning satellite receiver or cable TV buttons to
Remote Control
Front
6 7
Cursor operation
Enter setting
Calling out the menus
Setup
Return
1 Switch
Multi-Zone
CH + –
uio p
ENTER
MENU
SETUP
RETURN
(fast-reverse / fast-forward)
Channelz
Power off
Power on or Power on / Standby
Play
Stop
Pause
Disc skip +
Manual search
(fast-reverse / fast-forward)
Auto search (cue)
Playback
6 7
POWER OFF
ON/SOURCE
1
2
SHIFT, 3
SKIP +
Power on / Standby
Playz
Pausez
Stopz
Manual search z
Settings
ON/SOURCE
1
3
2
DEVICE SELECT
Connections
DEVICE SELECT
The Blu-ray disc Player/DVD player, Digital Video recorder, video deck,
or CD player can be operated as described below even when
is set to the “SAT/CBL” or “TV” position.
•Play
•Stop
•Pause
•fast-forward
•fast-reverse
•Auto Search
Getting Started
Assigning buttons that are Not
Used to Operate Other Devices
(Punch Through Function)
Operating Registered Devices
This is set to “No setting” upon purchase.
54
ENGLISH
Getting Started
Other Information
Surround
Settings
Dolby Digital
Dolby Pro Logic gx
DTS Digital Surround
Dolby Digital is a multichannel digital signal format developed by Dolby
Laboratories.
A total of 5.1-channels are played: 3 front channels (“FL” , “FR” and
“C”), 2 surround channels (“SL” and “SR”) and the “LFE” channel for
low frequencies.
Because of this, there is no crosstalk between channels and a realistic
sound field with a “three-dimensional” feeling (sense of distance,
movement and positioning) is achieved.
A real, overpowering sense of presence is achieved when playing
movie sources in AV rooms as well.
Dolby Pro Logic gx is a further improved version of the Dolby Pro Logic
g matrix decoding technology.
Audio signals recorded in 2-channels are decoded to achieve a natural
sound with up to 7.1-channels.
There are 3 modes: “Music” suited for playing music, “Cinema”
suited for playing movies, and “Game” which is optimized for playing
games.
DTS Digital Surround is the standard digital surround format of DTS,
Inc., compatible with a sampling frequency of 44.1 or 48 kHz and up
to 5.1-channels of digital discrete surround sound.
Playback
Connections
The AVR-1910 is equipped with a digital signal processing circuit that lets you play program sources in the surround mode to achieve the same sense of presence as in a movie theater.
Dolby Surround
Multi-Zone
Remote Control
Dolby Digital Plus
Information
Dolby Digital Plus is an improved Dolby Digital signal format that is
compatible with up to 7.1-channels of discrete digital sound and also
improves sound quality thanks to extra data bit rate performance. It
is upwardly compatible with conventional Dolby Digital, so it offers
greater flexibility in response to the source signal and the conditions
of the playback equipment.
Troubleshooting
Dolby TrueHD
Specifications
Dolby TrueHD is a high definition audio technology developed by Dolby
Laboratories, using lossless coding technology to faithfully reproduce
the sound of the studio master.
This format is compatible with a maximum sampling frequency of 96
kHz and up to 7.1-channels, so it is used for applications particularly
prioritizing sound quality.
Dolby Pro Logic g
Dolby Pro Logic g is a matrix decoding technology developed by Dolby
Laboratories.
Regular music such as that on CDs is encoded into 5-channels to
achieve an excellent surround effect.
The surround channel signals are converted into stereo and full band
signals (with a frequency response of 20 Hz to 20 kHz or greater)
to create a “three-dimensional” sound image offering a rich sense of
presence for all stereo sources.
55
DTS Surround
Dolby Digital EX
Dolby Digital EX is a 6.1-channel surround format proposed by Dolby
Laboratories that allows users to enjoy in their homes the “DOLBY
DIGITAL SURROUND EX” audio format jointly developed by Dolby
Laboratories and Lucas Films.
The 6.1 channels of sound, including surround back channels, provide
improved sound positioning and expression of space.
Dolby Pro Logic gz
Dolby Pro Logic gz introduces a new dimension to Home Entertainment
through the addition of a pair of front height channels. Compatible with
stereo, 5.1 and 7.1 content, Dolby Pro Logic gz provides enhanced
spaciousness, depth and dimension to movies, concert video and
videogame playback while maintaining the full integrity of the source
mix.
Dolby Pro Logic gz identifies and decodes spatial cues that occur
naturally in all content, directing this information to the front height
channels, complementing the performance of left and right surround
sound speakers. Content that is encoded with Dolby Pro Logic
gz height channel information can be even more revealing, with
perceptually discrete height channel information bringing an exciting
new dimension to home entertainment. Dolby Pro Logic gz, with
front height channels is also an ideal alternative for households that
cannot support the placement of back surround speakers of a typical
7.1 channel system but may have bookshelf space available to support
the addition of height speakers.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks of
Dolby Laboratories.
DTS-HD High Resolution Audio
DTS-HD High Resolution Audio is an improved version of the
conventional DTS, DTS-ES and DTS 96/24 signals formats, compatible
with sampling frequencies of 96 or 48 kHz and up to 7.1-channels
of discrete digital sound. High data bit rate performance provides
high quality sound. This format is fully compatible with conventional
products, including conventional DTS digital surround 5.1-channel
data.
DTS-HD Master Audio
DTS-HD Master Audio is DTS, Inc’s lossless audio format compatible
with up to 96 kHz/7.1-channels. The lossless audio coding technology
faithfully reproduces the sound of the studio master. It is fully
compatible with conventional products, including conventional DTS
digital surround 5.1-channel data.
DTS-ES™ Discrete 6.1
DTS-ES™ Discrete 6.1 is a 6.1-channel discrete digital audio format
adding a surround back (SB) channel to the DTS digital surround sound.
Decoding of conventional 5.1-channel audio signals is also possible
according to the decoder.
DTS-ES™ Matrix 6.1
DTS-ES™ Matrix 6.1 is a 6.1-channel discrete digital audio format
inserting a surround back (SB) channel to the DTS digital surround
sound through matrix encoding. Decoding of conventional 5.1-channel
audio signals is also possible according to the decoder.
DTS NEO:6™ Surround
DTS NEO:6™ is a matrix decoding technology for achieving 6.1channel surround playback with 2-channel sources. It includes “DTS
NEO:6 Cinema” suited for playing movies and “DTS NEO:6 Music”
uited for playing music.
ENGLISH
Audyssey Dynamic Volume™
DTS 96/24 is a digital audio format enabling high sound quality
playback in 5.1-channels with a sampling frequency of 96 kHz and 24
bit quantization on DVD-Video.
Audyssey Dynamic Volume solves the problem of large variations in
volume level between television programs, commercials, and between
the soft and loud passages of movies.
Audyssey Dynamic EQ is integrated into Dynamic Volume so that as
the playback volume is adjusted automatically, the perceived bass
response, tonal balance, surround impression, and dialog clarity
remain the same.
Manufactured under license from Audyssey Laboratories. U.S.
and foreign patents pending. Audyssey MultEQ® is a registered
trademark of Audyssey Laboratories. Audyssey Dynamic EQ™ is a
trademark of Audyssey Laboratories. Audyssey Dynamic Volume™
is a trademark of Audyssey Laboratories.
Playback
Audyssey
Settings
Manufactured under license under U.S. Patent #’s: 5,451,942;
5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,212,872;
7,333,929; 7,392,195; 7,272,567 & other U.S. and worldwide patents
issued & pending. DTS is a registered trademark and the DTS
logos, Symbol, DTS-HD and DTS-HD Master Audio are trademarks
of DTS, Inc.© 1996-2008 DTS, Inc. All Rights Reserved.
Connections
DTS 96/24
Getting Started
Surround
Multi-Zone
Audyssey MultEQ®
Remote Control
Audyssey MultEQ is a room equalization solution that calibrates any
audio system so that it can achieve optimum performance for every
listener in a large listening area. Based on several room measurements,
MultEQ calculates an equalization solution that corrects for both
time and frequency response problems in the listening area and also
performs a fully automated surround system setup.
Audyssey Dynamic EQ™
Information
Troubleshooting
Audyssey Dynamic EQ solves the problem of deteriorating sound
quality as volume is decreased by taking into account human perception
and room acoustics. Audyssey Dynamic EQ works in tandem with
Audyssey MultEQ to provide well-balanced sound for every listener
at any volume level.
Specifications
56
ENGLISH
Getting Started
Surround
Surround Modes and Parameters
Signals and adjustability in the different modes
Parameter (default values are shown in parentheses)
Center
PURE DIRECT, DIRECT
S
D
D
D
A
D
S (OFF)
S (0dB)
A
A
MULTI CH DIRECT
S
D
D
D
A
D
A
S (0dB)
S (ON)
S
STEREO
S
A
A
A
A
D
S (OFF)
S (0dB)
A
EXT. IN
S
D
D
D
A
D
A
A
MULTI CH IN
S
D
D
D
A
D
A
S (0dB)
DOLBY PRO LOGIC gx
S
D
D
D
A
D
S (OFF)
A
A
S
DOLBY PRO LOGIC g
S
D
D
A
A
D
S (OFF)
A
A
DTS NEO:6
S
D
D
D
A
D
S (OFF)
A
A
DOLBY PRO LOGIC gz
S
D
D
A
D
D
S (OFF)
A
A
A
S (OFF)
DOLBY DIGITAL
S
D
D
D
D
D
S (OFF)
S (0dB)
S (ON)
S
DOLBY DIGITAL Plus
S
D
D
D
D
D
S (OFF)
S (0dB)
S (ON)
DOLBY TrueHD
S
D
D
D
D
D
S (OFF)
S (0dB)
DTS SURROUND
S
D
D
D
D
D
S (OFF)
Remote Control
DTS 96/24
S
D
D
D
D
D
S (OFF)
DTS-HD
S
D
D
D
D
D
5CH/7CH STEREO
S
D
D
D
D
ROCK ARENA
S
D
D
D
JAZZ CLUB
S
D
D
MONO MOVIE
S
D
Information
VIDEO GAME
S
MATRIX
VIRTUAL
Settings
Front L/R
Surround
L/R
Multi-Zone
Surround mode
Playback
Connections
Channel output
Surround Front Height
Su­b­­­­woofer
Back L/R
L/R
LFE
AFDM
Room Size
Effect
Delay time
Subwoofer
A
A
A
A
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
S (Auto)
A
A
A
A
A
A
A
A
A
S (ON)
S
A
A
A
A
A
A
A
S (NOTE1) S (Cinema)
A
A
A
A
S (Auto)
S
S (NOTE2) S (Cinema)
A
A
A
A
S (Auto)
S
S (NOTE1) S (Cinema)
A
A
A
A
A
A
A
A
A
A
A
S (OFF)
A
A
A
A
A
A
S
S (OFF)
A
A
A
A
A
A
S (ON)
S
S (OFF)
A
A
A
A
A
S (Auto)
S (0dB)
S (ON)
S
S (OFF)
A
A
A
A
A
A
S (0dB)
S (ON)
S
S (OFF)
A
A
A
A
A
A
S (OFF)
S (0dB)
S (ON)
S
S (OFF)
A
A
A
A
A
A
D
S (OFF)
S (0dB)
A
S
A
A
A
A
A
A
A
D
D
S (OFF)
S (0dB)
A
S
A
A
S (Medium)
S (10)
A
A
A
D
D
D
S (OFF)
S (0dB)
A
S
A
A
S (Medium)
S (10)
A
A
A
D
D
D
D
S (OFF)
S (0dB)
A
S
A
A
S (Medium)
S (10)
A
A
A
D
D
D
D
D
S (OFF)
S (0dB)
A
S
A
A
S (Medium)
S (10)
A
A
A
S
D
D
D
D
D
S (OFF)
S (0dB)
A
S
A
A
A
A
S (30 ms)
A
A
S
A
A
A
A
D
S (OFF)
S ( 0dB)
A
A
A
A
A
A
A
A
A
z1
z2
z1
SB CH Out Cinema EQ.
DRC
Mode
Troubleshooting
S: Signal / Adjustable
A : No signal / Not adjustable
D:Turned on or off by speaker configuration setting
Specifications
57
D. Comp
S: Signal / Adjustable
A : No signal / Not adjustable
NOTE1 :This parameter is available when the menu “Mode” (vpage 44) is set to “Cinema”.
NOTE2 :T his parameter is available when the menu “Mode” (vpage 44) is set to “Cinema” or “PL”.
NOTE:
z1 :When playing Dolby Digital and DTS signals.
z2 :When playing Dolby Digital, DTS and Linear PCM (multi ch).
z3 :When playing Dolby TrueHD signal.
z3
S (Auto)
ENGLISH
Signals and adjustability in the different modes
Parameter (default values are shown in parentheses)
Surround mode
PRO LOGIC g/gx MUSIC mode only
NEO:6 MUSIC
mode only
EXT. IN only
MultEQ
Dynamic EQ
(NOTE5)
Dynamic
Volume
(NOTE6)
RESTORER
(NOTE7)
A
Dimension
C. Width
Center Image
SW ATT
PURE DIRECT, DIRECT
A
A
A
A
A
A
A
A
A
MULTI CH DIRECT
A
A
A
A
A
A
A
A
A
A
STEREO
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
EXT. IN
A
A
A
A
S
A
A
A
A
A
MULTI CH IN
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
DOLBY PRO LOGIC gx
S (OFF)
S (3)
S (3)
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
DOLBY PRO LOGIC g
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
S (0.3)
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
DOLBY PRO LOGIC gz
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
DOLBY DIGITAL
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
DOLBY DIGITAL Plus
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
DOLBY TrueHD
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
DTS SURROUND
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
DTS-96/24
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
DTS-HD
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
A
5CH/7CH STEREO
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
ROCK ARENA
A
A
A
A
A
S (NOTE3)
S (OFF)
S (OFF)
S (OFF)
S
JAZZ CLUB
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
MONO MOVIE
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
VIDEO GAME
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
MATRIX
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
VIRTUAL
A
A
A
A
A
S (0dB)
S (OFF)
S (OFF)
S (OFF)
S
Information
A
A
Remote Control
S (3)
A
Multi-Zone
S (3)
A
Playback
S (OFF)
DTS NEO:6
Settings
Panorama
Connections
Tone
(NOTE4)
Getting Started
Surround
Troubleshooting
S: Adjustable
A : Not adjustable
NOTE3 :BASS +6 dB, TREBLE +4 dB
NOTE4 :Cannot be set when the “Dynamic EQ” (vpage 47) setting is “ON”.
NOTE5 :Cannot be set when the “MultEQ” (vpage 46) setting is “OFF”.
NOTE6 :Cannot be set when the “Dynamic EQ” (vpage 47) setting is “OFF”.
NOTE7 :“RESTORER” can be set for analog or PCM 48 k or 44.1 k input signals.
Specifications
58
ENGLISH
Getting Started
Surround
Differences in Surround Mode Names Depending on the Input Signals
Input signals
Button
PCM
Connections
Surround mode
Note
Linear
ANALOG
PCM
(multi ch)
DTS-HD
Linear
PCM
(2ch)
DTS-HD
Master
Audio
DTS
DTS-HD
High
Resolution
Audio
DTS ES
DTS ES
DSCRT
MTRX
(With Flag) (With Flag)
DOLBY
DTS
(5.1ch)
DTS
96/24
DOLBY DIGITAL
DOLBY
DOLBY
DIGITAL
TrueHD
Plus
DOLBY
DIGITAL
EX (With
Flag)
DOLBY
DOLBY
DIGITAL EX
DIGITAL
(With no
(5.1/5/4ch)
Flag)
DOLBY
DIGITAL
(4/3ch)
DOLBY
DIGITAL
(2ch)
STANDARD
Settings
DTS SURROUND
DTS-HD MSTR
A
A
A
F
A
A
A
A
A
A
A
A
A
A
A
A
DTS-HD HI RES
A
A
A
A
F
A
A
A
A
A
A
A
A
A
A
A
Playback
DTS ES DSCRT6.1
z1 z3
A
A
A
A
A
F D
A
A
A
A
A
A
A
A
A
A
DTS ES MTRX6.1
z1 z3
A
A
A
A
A
A
F D
A
A
A
A
A
A
A
A
A
DTS SURROUND
A
A
A
A
A
S
S
F
A
A
A
A
A
A
A
A
DTS 96/24
A
A
A
A
A
A
A
A
F
A
A
A
A
A
A
A
Multi-Zone
DTS (–HD) + PLgx CINEMA
z2 z3
A
A
A
S
S
S
S
S
S
A
A
A
A
A
A
A
DTS (–HD) + PLgx MUSIC
z1 z3
A
A
A
S
S
S
S
S
S
A
A
A
A
A
A
A
DTS (–HD) + PLgz
z1 z4
A
A
A
S
S
S
S
S
S
A
A
A
A
A
A
A
DTS (–HD) + NEO:6
z1 z3
A
A
A
S
S
A
S
S
S
A
A
A
A
A
A
A
Remote Control
DTS NEO:6 CINEMA
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DTS NEO:6 MUSIC
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY TrueHD
A
A
A
A
A
A
A
A
A
F
A
A
A
A
A
A
DOLBY DIGITAL+
A
A
A
A
A
A
A
A
A
A
F
A
A
A
A
A
DOLBY SURROUND
Information
DOLBY DIGITAL EX
z1 z3
A
A
A
A
A
A
A
A
A
A
A
S
S
S
S
A
DOLBY (D+) (HD) +EX
z1 z3
A
A
A
A
A
A
A
A
A
S
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
S
F
F
F
A
DOLBY DIGITAL
DOLBY (D) (D+) (HD) +PLgx CINEMA
z2 z3
A
A
A
A
A
A
A
A
A
S
S
F D
S
S
S
A
DOLBY (D) (D+) (HD) +PLgx MUSIC
z1 z3
A
A
A
A
A
A
A
A
A
S
S
S
S
S
S
A
Troubleshooting
DOLBY (D) (D+) (HD) +PLgz
z1 z4
A
A
A
A
A
A
A
A
A
S
S
S
S
S
S
A
DOLBY PRO LOGIC gx CINEMA
z3
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY PRO LOGIC gx MUSIC
z3
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY PRO LOGIC gx GAME
z3
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY PRO LOGIC gz
z4
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY PRO LOGIC g CINEMA
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
Specifications
DOLBY PRO LOGIC g MUSIC
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY PRO LOGIC g GAME
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
DOLBY PRO LOGIC
S
A
S
A
A
A
A
A
A
A
A
A
A
A
A
S
NOTE:
z1: This mode is not available when the surround back speaker setup is set to “None”.
z2: This mode is not available when the surround back speaker setup is set to “1sp” or “None”.
z3: Can be set when “Amp Assign” is set to “Normal”
.
z4: Not selectable when “Amp Assign” is set to anything other than “Front Height”
.
59
F : Mode selectable in initial status
D : Mode fixed when “AFDM” is “ON”
S : Selectable mode
A : Non-selectable mode
ENGLISH
Input signals
Button
PCM
Surround mode
Note
DTS
Linear
PCM
(2ch)
DTS-HD
Master
Audio
DTS-HD
High
Resolution
Audio
DTS ES
DTS ES
DSCRT
MTRX
(With Flag) (With Flag)
DOLBY
DTS
(5.1ch)
DTS
96/24
DOLBY DIGITAL
DOLBY
DOLBY
DIGITAL
TrueHD
Plus
DOLBY
DIGITAL
EX (With
Flag)
DOLBY
DOLBY
DIGITAL
DIGITAL
EX (With
(5.1/5/4ch)
no Flag)
DOLBY
DIGITAL
(4/3ch)
DOLBY
DIGITAL
(2ch)
STANDARD
MULTI CH IN
MULTI CH IN
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
MULTI IN + PLgx MUSIC
z1 z3
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
MULTI IN + PLgz
z1 z5
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
MULTI IN + Dolby EX
z1 z3
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
z3
A
F D (7.1)
A
A
A
A
A
A
A
A
A
A
A
A
A
A
MULTI CH IN 7.1
Playback
F
z2 z3
Settings
A
MULTI IN + PLgx CINEMA
DIRECT
S
A
S
S
S
S
S
S
S
S
S
S
S
S
S
S
MULTI CH DIRECT
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
z2 z3
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
M DIRECT + PLgx MUSIC
z1z3
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
M DIRECT + PLgz
z1z5
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
M DIRECT + Dolby EX
z1 z3
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
z3
A
S (7.1)
A
A
A
A
A
A
A
A
A
A
A
A
A
A
M DIRECT 7.1
Remote Control
M DIRECT + PLgx CINEMA
Multi-Zone
DIRECT
PURE DIRECT
PURE DIRECT
S
A
S
S
S
S
S
S
S
S
S
S
S
S
S
S
MULTI CH PURE DIRECT
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
M PURE D + PLgx MUSIC
z1 z3
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
M PURE D + PLgz
z1 z5
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
M PURE D + Dolby EX
z1 z3
A
S
A
A
A
A
A
A
A
A
A
A
A
A
A
A
z3
A
S (7.1)
A
A
A
A
A
A
A
A
A
A
A
A
A
A
z4
M CH PURE DIRECT 7.1
Troubleshooting
z2 z3
Information
M PURE D + PLgx CINEMA
DSP SIMULATION
5CH/7CH STEREO
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
JAZZ CLUB
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
MONO MOVIE
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
VIDEO GAME
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
MATRIX
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
VIRTUAL
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
S
F
S
F
S
S
S
S
S
S
S
S
S
S
S
S
S
Specifications
S
ROCK ARENA
STEREO
STEREO
NOTE :
z1: This mode is not available when the surround back speaker setup is set to “None”.
z2: This mode is not available when the surround back speaker setup is set to “1sp” or “None”.
z3: Can be set when “Amp Assign” is set to “Normal”
.
z4: If the surround back speaker setup is set to “None”, then “5CH STEREO” is displayed.
z5: Not selectable when “Amp Assign” is set to anything other than “Front Height”
.
Connections
Linear
ANALOG
PCM
(multi ch)
DTS-HD
Getting Started
Surround
F : Mode selectable in initial status
D : Mode fixed when “AFDM” is “ON”
S : Selectable mode
A : Non-selectable mode
60
ENGLISH
Getting Started
Troubleshooting
Connections
Settings
If a problem should arise, first check the following:
1. Are the connections correct?
2. Is the set being operated as described in the owner’s manual?
3. Are the other components operating properly?
If this unit does not operate properly, check the items listed in the table below. Should the problem persist,
there may be a malfunction.
In this case, disconnect the power immediately and contact your store of purchase.
GGeneralH
Playback
Multi-Zone
Remote Control
Symptom
Set does not
operate properly.
Power does not
turn on, or turns
off directly after it
was turned on.
No sound is
produced from
speakers.
Cause
Countermeasure
•External noise or interference is •Reset the microprocessor.
causing the set to malfunction.
•Connection of the power cord is •Check the insertion of the power
faulty.
cord plug.
Information
•Connection with the input
devices or connection of the
speaker cables is faulty.
•Device you want to play and set
input source do not match.
•Master volume is turned too
low.
•Mute mode is set.
•Headphones are connected.
•No digital signals are being
input.
•Check the connections.
Troubleshooting
Specifications
•Select an appropriate input
source.
•Adjust the master volume to an
appropriate level.
•Cancel the mute mode.
•Disconnect the headphones.
•Select an input source for which
the digital input setting has been
made.
•The connectors to which the •Set the input mode.
digital inputs are assigned and
the settable input modes do not
match.
Display is off.
•The “Display” setting is set to •Set to something other than
“OFF”.
“OFF”.
•The PURE DIRECT mode is set. •Set a surround mode other than
the PURE DIRECT mode.
“DOLBY DIGITAL” •Blu-ray Disc player / DVD player’s •Check the Blu-ray Disc player /
indicator does not
digital audio output setting is not DVD player’s audio output setting.
appear on display.
proper.
For details, read the Blu-ray Disc
player / DVD player’s operating
instructions.
61
Page
64
17
11
38
38
42
42
33
34
31
44
–
Symptom
Power switches
off suddenly while
you are using the
AVR-1910, the
power indicator
will flash in red
at intervals of
approximately 2
seconds.
Power switches
off suddenly while
you are using the
AVR-1910, the
power indicator
will flash red
at intervals of
approximately 0.5
seconds.
Even applying
power, the power
display flashes
red at intervals of
approximately 0.5
seconds.
Set does not work
properly when
remote control
unit operated.
Cause
Countermeasure
•The protection circuit will be •Please switch off power at once,
activated depending upon the and re-apply the power after
temperature rise in the internal the body temperature has fallen
parts of the unit.
sufficiently.
•Please re-install AVR-1910 in a
place having good ventilation.
Page
3
•Use speakers having impedance •Please use speakers which have
less than that specified.
the specified impedance.
•If speaker cable core wires touch •Unplug the power cord, then
each other or the core wires after twisting the core wires
become disconnected from their together tightly again, or effecting
terminals, the protection circuit termination treatments etc,
will be activated in the event of please reconnect once again.
core wires coming into contact
with the AVR-1910 rear panel.
•The AVR-1910 amplifier circuit •Switch off the power and please
has failed.
contact the DENON service
adviser.
12
•Batteries are worn.
•You are operating outside of the
specified range.
•Obstacle between main unit and
remote control unit.
•The batteries are not inserted in
the proper direction, as indicated
by the polarity marks in the
battery compartment.
•The set’s remote control sensor
is exposed to strong light (direct
sunlight, inverter type fluorescent
bulb light, etc.).
•Settings do not match the remote
control unit’s DEVICE SELECT
switch.
•Replace with new batteries.
•Operate within the specified
range.
•Remove the obstacle.
3
3
•Insert the batteries in the
proper direction, following the
polarity marks in the battery
compartment.
•Move the set to a place in which
the remote control sensor will
not be exposed to strong light.
3
•Match the settings to the remote
control unit’s DEVICE SELECT
switch.
52
–
12
–
3
3
ENGLISH
42, 43
Symptom
No picture
appears.
45
42
–
25
Picture cannot be
recorded.
11
50
–
–
35
28
DVDs cannot be
copied on a DVR.
The menu screen
and status
indicators are not
displayed.
Cause
•The connections between the
AVR-1910 and monitor are faulty.
•The monitor’s input setting is
wrong.
•PURE DIRECT mode is set.
•The player is connected using
the component input connectors,
the monitor is connected
using the video (yellow) output
connectors.
Countermeasure
•Check the connections.
•Set properly.
Page
13 ~ 16
–
•Cancel the PURE DIRECT mode.
•High definition (1080i/720p) and
progressive (480p/576p) video
signals are not down-converted.
Set the player to interlace
(480i/576i) signals.
44
–
•Input source does not match •The video conversion function
recorder’s video connection does not work for the REC
connector (video).
OUT connectors. Match the
input source and recorder
connections.
•This is not a malfunction. Most
movie software includes copy
–
prevention signals and cannot be
copied.
•When
viewing
HDMI
or
component video signals via the
AVR-1910, the on-screen display
appears when the MENU button
on the main unit or the MENU
button on the main remote
control unit.
•“OFF” is displayed for the •Set “Manual Setup” – “Option
status.
Setup” – “On-Screen Display”
– “Text” to “ON”.
•The main volume display is •Set “Manual Setup” – “Option
“OFF”.
Setup” – “On-Screen Display”
– “Master Volume” to “Top” or
•The display during tuner operation “Bottom”.
is “OFF”.
•Set when “Manual Setup”
– “On-Screen Display” – “Tuner
•The display during iPod operation Information” is not “OFF”.
is “OFF”.
•Set when “Manual Setup”
– “On-Screen Display” – “ iPod
Information” is not “OFF”.
15
–
9
30
Specifications
28
GVideoH
Troubleshooting
•The “Manual Setup” – “HDMI • Set to “TV”.
Setup” – “HDMI Audio Out”
setting is set to “AMP”.
26
–
Information
25
Page
13
–
Remote Control
•The surround back speaker’s •Check the setting and change it
power amplifier is assigned to a as necessary.
different channel.
•“S.Back” setting is set to •Set to something other than
“None”.
“None”.
•The “Parameter” – “Surround •Please set “Parameter” –
Parameter” – “SB CH Out” “Surround Parameter” – “SB
settings are “OFF”.
CH Out” to settings other than
“OFF”.
•Surround mode not set to a mode •Select a surround playback
for 6.1- or 7.1-channel playback.
mode.
•Subwoofer’s power not turned •Turn on the subwoofer’s power.
on.
•The “Subwoofer” setting at •Set to “Yes”.
“Speaker Config.” is set to “No”.
•The subwoofer is not properly •Check the connections.
connected.
•The subwoofer’s volume is •Adjust the subwoofer’s volume
turned off.
to an appropriate level.
•Blu-ray Disc player / DVD player’s •Set the Blu-ray Disc player / DVD
audio output setting is not set to player. For details, refer to the
bitstream.
Blu-ray Disc player / DVD player’s
operating instructions.
•Blu-ray Disc player / DVD player is •Use a DTS-compatible player.
not compatible with DTS sound
playback.
•The AVR-1910’s “Decode Mode” •Set to the “Auto” or “DTS”
setting is set to “PCM”.
mode.
•The “Manual Setup” – “HDMI •Set to “AMP”.
Setup” – “HDMI Audio Out”
setting is set to “TV”.
Cause
Countermeasure
•Connect the HDMI.
•HDMI is not connected.
•Blu-ray Disc player’s audio output •Set the Blu-ray Disc player. For
setting is not set to bitstream.
details, refer to the Blu-ray Disc
player’s operating instructions.
•Blu-ray Disc player is not •Use a DTS-compatible player.
compatible with DTS sound
playback.
Multi-Zone
HDMI audio
signals are not
output from
speakers.
No sound is
output from
the monitor
connected
with HDMI
connections.
Symptom
Dolby TrueHD,
DTS-HD, Dolby
Digital Plus audio
is not output.
Playback
DTS sound is not
output.
Page
42
Settings
No sound is
produced from
subwoofer.
Cause
Countermeasure
•You are playing a monaural source •The mode is set to something
(TV, etc.) in the “STANDARD” other than “STANDARD” (Dolby/
(Dolby/DTS Surround) mode.
DTS Surround).
•The surround mode is set to •Set to a surround playback
“STEREO”, “DIRECT” or “PURE mode.
DIRECT”.
Connections
Symptom
No sound is
produced from
center speaker.
No sound
is produced
from surround
speakers.
No sound is
produced from
surround back
speaker.
Getting Started
GAudioH
30
31
31
62
ENGLISH
Getting Started
GSIRIUS Satellite RadioH
GHDMIH
Connections
Settings
Playback
Multi-Zone
Symptom
HDMI audio
signals are not
output from
speakers.
Cause
Countermeasure
•The “Manual Setup” – “HDMI •Set to “Amp”
Setup” – “HDMI Audio Out”
setting is set to“TV”
No picture
appears
with HDMI
connections.
•The connections to the HDMI
connectors are faulty.
•HDMI input setting is improper.
•The monitor is not compatible
with
copyright
protection
(HDCP).
•The HDMI format of the player
and monitor do not match.
•The “Manual Setup” – “HDMI
Setup” – “HDMI Audio Out”
setting is set to “Amp”.
Remote Control
Information
Troubleshooting
No sound is
output from
the monitor
connected
with HDMI
connections.
When performing •HDMI’s
CEC
the following
operating.
operations on a
connected device,
AVR-1910 has the
same operations.
⋅Power ON/OFF
⋅Switching audio
output devices
⋅Adjust volume
⋅Switch input
source
function
Page
28
•Check the connections.
13
•Check the HDMI input setting.
•Connect a monitor that is
compatible
with
copyright
protection (HDCP).
•Match the HDMI format of the
player and monitor.
•Set to “TV”.
33
12
is •Set “Manual Setup” – “HDMI
Setup” -– “HDMI Control” to
“OFF”.
When you only want to operate
the power on/off each device, set
“Power Off Control” to “OFF”.
12
28
28
Symptom
Specifications
63
Cause
Countermeasure
•The input source assigned to •Switch to the input source
“iPod Dock” is not selected.
assigned at “iPod Dock”.
•Cable is not properly connected. •Reconnect.
•Control dock for iPod’s AC •Plug the control dock for iPod’s
adapter is not connected to AC adapter into a power outlet.
power outlet.
”Call SIRIUS”z
is displayed.
”SUBSCRIPTION
UPDATED” is
displayed.
”Enter Lock
Code [
]” is
displayed.
Cause
Countermeasure
•The SiriusConnect Home Tuner •Check that the connections are
unit is not connected.
correct.
Page
33
14
–
Page
16
•The antenna is not connected.
•Check that the connections are
correct.
16
•The signal cannot be received.
•Reposition the antenna.
–
•Channel is not present.
•Select another channel.
–
•The signal cannot be received.
•Reposition your SiriusConnect
Home Tuner and Home Dock
antenna.
•Displays while SiriusConnect •Reposition your SiriusConnect
Home Tuner is connected.
Home Tuner and Home Dock
antenna.
•Channels are not subscribed to. •If you subscribe to the channel,
you can receive the channel.
•While
updating
contract
–
information.
•Selected channels are locked.
•Please insert pass word (4 digits)
into “[
]”.
z: After scroll displays “Call 888-539-....” twice, displays “Call SIRIUS”.
GiPodH
iPod cannot be
played.
Symptom
“CHECK SIRIUS
TUNER” is
displayed.
”ANTENNA
ERROR” is
displayed.
”NO SIGNAL” is
displayed.
”INVALID
CHANNEL” is
displayed.
”ACQUIRING
SIGNAL” is
displayed.
–
–
–
–
41
ENGLISH
Playback
Multi-Zone
If in step 3 the display does not flash at intervals of about 1 second, start over from step 1.
• Power amplifier
Front (A, B):
Rated output:
(8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
90 W+90 W
125 W+125 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Center:
90 W
(8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
125 W
(6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Surround:
90 W+90 W
(8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
125 W+125 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Surround Back:
90 W+90 W
(8 Ω/ohms, 20 Hz ~ 20 kHz with 0.08 % T.H.D.)
125 W+125 W (6 Ω/ohms, 1 kHz with 0.7 % T.H.D.)
Output connectors:
Front:
A or B
6~16 Ω/ohms
A + B
12~16 Ω/ohms
Center, Surround, Surround Back / Amp Assign:
6~16 Ω/ohms
• Analog
Input sensitivity / Input impedance: 200 mV / 47 kΩ/kohms
10 Hz ~ 100 kHz — +1, –3 dB (DIRECT mode)
Frequency response:
100 dB (IHF-A weighted, DIRECT mode)
S/N:
Settings
1 Turn off the power using on the main unit.
and
on the main unit.
2 Press while simultaneously pressing
the display starts flashing at intervals of about 1 second, release the two
3 Once
buttons.
nAudio section
Connections
Perform this procedure if the display is abnormal or if operations cannot be performed.
When the microprocessor is reset, all the settings are reset to their default values.
Specifications
Getting Started
Restoring all the settings to as they were at the
time of purchase
(Resetting the Microprocessor)
Remote Control
nVideo section
nTuner section
Y (brightness) signal — 1 Vp-p, 75 Ω/ohms
PB / CB signal — 0.7 Vp-p, 75 Ω/ohms
PR / CR signal — 0.7 Vp-p, 75 Ω/ohms
5 Hz ~ 60 MHz — +0, –3 dB
[AM]
520 kHz ~ 1710 kHz
18 µV
Specifications
[FM]
(note: µV at 75 Ω/ohms, 0 dBf = 1 x 10-15 W)
87.5 MHz ~ 107.9 MHz
1.2 µV (12.8 dBf)
MONO 2.8 µV (20.2 dBf)
STEREO 48.7 µV (45.0 dBf)
MONO 70 dB
STEREO 67 dB
MONO 0.7 %
STEREO 1.0 %
Troubleshooting
Receiving Range:
Usable Sensitivity:
50 dB Quieting Sensitivity:
S/N (IHF-A):
Total harmonic Distortion (at 1 kHz):
1 Vp-p, 75 Ω/ohms
5 Hz ~ 10 MHz — +1, –3 dB
Information
• Standard video connectors
Input / output level and impedance:
Frequency response:
• Color component video connector
Input / output level and impedance:
Frequency response:
nGeneral
Power supply:
Power consumption:
Maximum external dimensions:
Weight:
AC 120 V, 60 Hz
5.5 A
0.3 W (Standby)
434 (W) x 171 (H) x 377 (D) mm (17-3/32” x 6-47/64” x 14-27/32”)
10.7 kg (25 lbs 5.7 oz)
nRemote control unit (RC-1117)
Batteries:
Maximum external dimensions:
Weight:
R6/AA Type (two batteries)
52 (W) x 243 (H) x 21 (D) mm (2-3/64” x 9-9/16” x 53/64”)
184 g (Approx 6.5 oz) (including batteries)
z For purposes of improvement, specifications and design are subject to change without notice.
64
List of preset codes / Liste de codes préréglés
Contec
Contec/Cony
Craig
Crosley
Crown
CTX
DEVICE SELECT : TV
Television
A
B
C
3M
Addison
Admiral
Advent
Adventura
Aiko
Akai
Albatron
Alleron
America Action
Ampro
Amtron
Anam
Anam National
AOC
Apex
Apex Digital
Audiovox
Aventura
Axion
Bang & Olufsen
Barco
Baur
Belcor
Bell & Howell
Benq
Blue Sky
Bradford
Brillian
Brockwood
Broksonic
byd:sign
Candle
Carnivale
Carver
CCE
Celebrity
Celera
Changhong
Ching Tai
Chun Yun
Chung Hsin
Citizen
Clarion
Coby
100
163
033, 044, 050, 141
130
041
138
018, 019, 034, 119, 137, 151
127, 131
039
139
129
038
139
035, 038
030, 036, 079, 137 151, 154
048, 062
174
038, 067, 071, 138, 139, 140
029
120
146
020
034
030
033
089, 135
020
038, 139
145
030
050, 139, 141
123
037, 041, 137, 151
137, 151
155
147, 152
034
048
048
163
157, 163, 169, 173
160, 169
037, 038, 049, 137, 138,
151, 153, 156
139
074
PRESET CODE
Curtis Mathes
D
CXC
Cytron
Daewoo
Daytron
Dell
Denon
DiamondVision
Dimensia
Disney
Dumont
Durabrand
E
Dwin
Electroband
Electrograph
Electrohome
Element
Emerson
F
G
Emprex
Envision
Epson
Erres
ESA
Ether
Firstar
Fujitsu
Funai
Furi
Futuretech
Gateway
GE
H
GFM
Gibralter
Go Video
Goldstar
Gradiente
Grundig
Grunpy
Haier
Hallmark
Hankook
Harman/Kardon
139
038
038, 139
049, 155
038, 139, 153
082
010, 019, 044, 137, 140,
143, 151, 153, 155, 156
038, 139
118
030, 036, 049, 138, 140, 153
030
012, 032
143
125
010
060
013, 030
012, 029, 050, 111, 136,
139, 141
044, 128
034
142
034, 035, 050
106
012, 029, 030, 038, 039,
049, 050, 139, 141, 153
124
137, 151
080, 097
149
018, 029
158
170
037, 039, 077
029, 038, 039, 139
165
038, 139
085, 142, 144
010, 012, 035, 040, 045,
055, 140
027, 028
013, 030, 137, 151
134
012, 030, 036, 137, 151
084
152
038, 039, 139
107, 114, 136, 148
012
158, 168, 169
155
I
J
K
L
M
Harvard
Havermy
Hello Kitty
Hewlett Packard
Hisense
Hitachi
HP
Hyundai
Ilo
IMA
Infinity
InFocus
Initial
Innova
Insignia
Janeil
JBL
JC Penney
JCB
Jean
Jinxing
JVC
Kawasho
Kaypani
KEC
Kenwood
Kioto
KLH
Kloss Novabeam
Kolin
KTV
LG
Logik
LXI
M&S
Magnasonic
Magnavox
Majestic
Marantz
Maxent
Mediator
Megapower
Megatron
Memorex
MGA
Megatron
Mintek
Mitsubishi
Monivision
038, 139
044
140
068
087, 167, 174
[014]z, 058, 103, 143, 181
031
133
090, 115, 117, 122
038
155
099
117
152
029, 108, 109, 110
041
155
010, 036, 037, 040
034
159, 163, 167, 170
161, 165, 167
023, 024, 025, 040, 050
034
154
139
030, 137, 151
020, 155
048
038, 041
166, 169
038, 137, 139, 147, 151, 153
012, 030, 036, 127, 151
033
010, 012, 155
155
049
028, 037, 047, 054, 056,
137, 151, 155
033
046, 137, 151, 152, 155
112, 142
149
127
012, 143
012, 029, 033, 036, 050, 141
012, 030, 036, 137, 151
013, 040, 153
117
012, 030, 036, 044, 057, 178
127, 131
N
O
P
Montgomery Ward
Motorola
MTC
Multitech
NAD
NEC
Netsat
Net-TV
Newave
Nikko
Norcent
Norwood Micro
Noshi
NTC
Olevia
Onwa
Oppo
Optoma
Optonica
Orion
Otto Versand
Panasonic
Penney
Philco
Philips
Q
R
Philips Magnavox
Phonola
Pilot
Pioneer
Polaroid
Portland
Prima
Princeton
Prism
Proscan
Proton
Protron
Proview
Pulsar
Pye
Quasar
Quelle
Radio Shack/
Realistic
Radiola
RadioShack
RCA
Realistic
033
035, 044
030, 036, 137, 151, 156
038, 139, 147
012, 152
030, 035, 036, 081, 137, 151
152
090, 142
163, 164, 168
012, 137, 138, 151
079, 174
090
150
138
064, 072, 078
038, 139
121
098
044
050, 141
034
007, 008, 009, 035, 040,
059, 069, 176
012, 030, 137, 150, 151,
153, 156
030, 035, 036, 037, 050,
137, 151, 155
020, 021, 022, 035, 037,
046, 066, 105, 149, 152,155
020, 046, 047
149
030, 137, 151, 153
180, 184
030, 048, 075
030, 036, 138, 153
083, 130
127
040
010
012, 154
073
086, 106
013, 030
149
035, 040
034
010, 038
149
012, 030, 137, 139, 151, 153
010, 011, 030, 035, 036,
043, 045, 150, 156
012, 030, 137, 139, 151, 153
S
Runco
Sampo
Samsung
Samsux
Sansui
Sanyo
SBR
Sceptre
Scimitsu
Scotch
Scott
Sears
SEI
Sharp
Shen Ying
Sheng Chia
Shogun
Signature
Simpson
Sinudyne
SKY
Skygiant
Sony
Soundesign
Sova
Sowa
Squareview
SSS
Starlite
Studio Experience
Superscan
Supre-Macy
Supreme
SVA
Sylvania
T
Symphonic
Synco
Syntax
Syntax-Brillian
Tacico
Tandy
Tatung
Technics
Techview
Techwood
Teco
Teknika
013, 137, 151
137, 142, 151, 153, 154
012, 018, 019, 030, 036,
101, 102, 137, 147, 151,
152, 156
153
050, 141
092
149
096
030
012
012, 030, 038, 039, 116, 139
010, 012, 029, 039, 088, 155
034
015, 016, 017, 044, 070,
153, 179, 183
163
044, 164
030
033
037
034
152
169
000, 001, 002, 034, 052,
053, 175, 182
012, 037, 038, 039, 139
073
162, 167
029
030, 038, 139
038, 139
131
044
041
034
020, 113, 148, 174
026, 027, 028, 029, 037,
063, 104, 137, 151, 155
029, 038, 139
157, 162, 163, 164, 168, 172
072
072, 088
163, 168
044
035, 090, 144, 159, 162, 167
040
132
040
159, 164, 168
030, 033, 036, 037, 038,
039, 138, 139, 153, 155, 156
Telefunken
TMK
Toshiba
U
V
W
Y
Z
Totevision
Trutech
Tuntex
TVS
US Logic
Vector Research
Vidikron
Vidtech
Viewsonic
Viking
Viore
Vizio
Wards
Westinghouse
White
Westinghouse
Yamaha
Yapshe
Zenith
019
012
003, 004, 005, 006, 030,
051, 156, 177
153
091
158, 163
050, 141
090
137, 151
155
012, 030, 036
061, 076, 142
041
115
061, 093, 094, 095, 126, 144
010, 012, 030, 033, 036,
039, 137, 151, 155
061, 065, 140
T
W
RCA
Sylvania
F
M
P
T
G
C
D
G
H
I
L
M
O
P
R
S
Akai
Apex
Axion
Coby
Cytron
DiamondVision
Disney
GFM
Haier
Ilo
Initial
Insignia
LG
Mintek
Oppo
Panasonic
Philips
Polaroid
RCA
Sansui
Sharp
Sylvania
028
059
006
Blu-ray Disc Player
D
Denon
030, 036, 137, 151
171
012, 013, 014, 030, 033,
042, 050, 138, 141
Accele Vision
Accurian
Advent
Akai
Alco
Allegro
Amphion
MediaWorks
AMW
Apex
011
026
B
C
D
E
Apple
Arrgo
Aspire
Astar
Audiovox
Axion
Bang & Olufsen
Blaupunkt
Blue Parade
BOSS
Broksonic
California Audio
Labs
Changhong
CineVision
Coby
Curtis Mathes
CyberHome
Cytron
Daewoo
Denon
Desay
DiamondVision
Disney
Durabrand
Emerson
H
121
I
DVD Player
A
049, 050, 141
119
062
120
074
118
125
060
028
114
117
117
108
030
117
121
069
066
075
010
051
070
027, 063
Magnavox
Panasonic
Toshiba
DEVICE SELECT : DVD/HDP
TV/DVD Combination
A
005, 051
065
TV/DVD/VCR Combination
TV/VCR Combination
R
S
Toshiba
Westinghouse
088
146
131
098, 126
129
142
117
117
025, 026, 027, 028, 049,
059, 136
109
043
132
090
075, 129
099
137
136
039
089
061, 126
128
071, 153
074, 142
050, 081
143
029, 043, 151, 152, 155, 156
097
057, 142
014, 070, [111]z, 112, 128
116
124, 125
053, 063
144
127, 138, 145
J
K
L
M
N
O
P
Enterprise
Epson
ESA
Fisher
Funai
Gateway
GE
GFM
Go Video
Gradiente
Greenhill
Haier
Harman/Kardon
Hitachi
Hiteker
Ilo
Initial
Insignia
Integra
Irradio
iSymphony
JBL
JVC
Kawasaki
Kenwood
KLH
Koss
Landel
Lasonic
Lenoxx
LG
Liquid Video
Liteon
Magnavox
Memorex
Microsoft
Mintek
Mitsubishi
Nesa
Next Base
Nexxtech
Onkyo
Oppo
Optoma
Oritron
Panasonic
Philips
Pioneer
Polaroid
Proceed
Proscan
138
120
145
139
145
068, 154
044, 054, 136
101
012, 142
128
136
103
082, 140
013
025
096
096, 136
055, 102, 145
039
091
108
140
030, 031, 032, 033, 034
129
080, 128
058, 129, 136
067, 134
147
141
133, 144
055, 076, 077, 095, 138, 142
134
068, 146
047, 062, 127, 135, 145
053, 126
044
096, 136
056
136
147
115
071, 135
100, 114
122
067, 134
017, 018, 019, 020, 021,
022, 023, 024, 078, 083,
084, 085, 128, 135
007, 037, 038, 047, 052,
064, 073, 104, 135
039, 040, 041, 042, 087
028, 086
025
044
Q
R
S
Protron
Qwestar
RCA
Regent
Rio
Rowa
Sampo
Samsung
Sansui
Sanyo
Sharp
Shinsonic
Sonic Blue
Sony
T
Sungale
Superscan
Sylvania
Symphonic
Teac
Technics
Theta Digital
Toshiba
U
V
W
X
Y
Z
Trutech
Urban Concepts
US Logic
Venturer
VocoStar
Westinghouse
Xbox
Yamaha
Zenith
119
067
035, 036, 039, 044, 129, 136
133
142
130
148, 150
011, 012, 013, 015, 016,
048, 128
008, 126
126, 139
051, 060, 079, 092, 093, 094
096
142
000, 001, 002, 003, 004,
005, 006 ,045, 065, 066,
105, 106, 107
113
127
046, 101, 123, 127, 145
038
129, 149, 157, 158
128
039
007, 008, 009, 010, 069,
126, 135
110
135
096
129
118
072
044
017, 128
055, 135, 138, 142
DVD/VCR Combination
B
C
G
I
P
S
T
Broksonic
CineVision
Go Video
Insignia
Panasonic
Samsung
Sony
Sylvania
Toshiba
061
074
012
055
018, 019, 020
012, 048
002, 003, 004, 005
046
007, 010
TV/DVD Combination
A
C
Akai
Apex
Audiovox
Axion
Coby
098
026
075
099
081
D
G
H
I
L
M
O
P
R
S
T
W
Cytron
DiamondVision
Disney
GFM
Haier
Ilo
Initial
Insignia
LG
Mintek
Oppo
Panasonic
Philips
Polaroid
RCA
Sansui
Sharp
Sylvania
Toshiba
Westinghouse
097
124
063
101
103
096
096
102
077
096
100
078
073
086
035
008
079
046, 123
008, 101
072
TV/DVD/VCR Combination
M
P
T
Magnavox
Panasonic
Toshiba
062
021
009
DEVICE SELECT : DVR/VCR
Digital Video Recorder
A
B
C
D
E
G
H
ABS
Alienware
Bang & Olufsen
CyberPower
Dell
035
035
079
035
035
063, 065, 066, 067, 071,
DIRECTV
073, 077
Dish Network
076
Dishpro
076
Echostar
076
Expressvu
076
Gateway
035
GOI
076
Hewlett Packard
035
HNS
072
Howard Computers 035
HP
035
HTS
076
Hughes Network
063, 065, 066, 067, 073
Systems
Humax
063
Hush
035
PRESET CODE
I
J
L
M
N
P
R
S
T
iBUYPOWER
JVC
Linksys
Media Center PC
Microsoft
Mind
Niveus Media
Northgate
Panasonic
Philips
Proscan
RCA
ReplayTV
Samsung
Sonic Blue
Sony
Stack
Systemax
Tagar Systems
Tivo
U
V
Z
Toshiba
Touch
UltimateTV
Viewsonic
Voodoo
ZT Group
035
063, 076
035
035
035
035
035
035
070
063, 065, 066, 067, 068, 072
077
063, 065, 072, 077
069
065, 067, 072
069
035, 064, 074, 078
035
035
035
063, 064, 065, 068, 073,
074, 078
035, 075
035
077
035
035
035
D
E
F
G
H
Video Cassette Recorder
A
B
C
ABS
Adventura
Aiwa
Akai
Alienware
American High
Asha
Audio Dynamics
Audiovox
Beaumark
Bell & Howell
Broksonic
Calix
Candle
Canon
CineVision
Citizen
Colortyme
Craig
Curtis Mathes
Cybernex
CyberPower
035
008, 033
008, 033
020
035
032
013, 030
018
031
013, 030
029
056
031
030, 031
032
058
030, 031
018
013, 030, 031
012, 018, 030, 032
013, 030
035
PRESET CODE
I
J
K
L
M
Daewoo
Davidson
DBX
Dell
Denon
DIRECTV
Durabrand
Dynatech
Electrohome
Electrophonic
Emerson
Fisher
Fuji
Funai
Garrard
Gateway
GE
Go Video
Goldstar
Gradiente
Harley Davidson
Harman/Kardon
Headquarter
Hewlett Packard
Hitachi
Howard Computers
HP
Hughes Network
Systems
Humax
Hush
iBUYPOWER
Insignia
Instant Replay
JC Penney
JCL
JVC
Kenwood
Kodak
LG
Linksys
Lloyd's
LXI
Magnasonic
Magnavox
Magnin
Marantz
Marta
Matsushita
Media Center PC
MEI
Memorex
019, 033
008
018
035
014
061
025
008, 033
010, 031
031
008, 010, 021, 031, 032, 033
029
026, 032
008, 021, 033
008, 033
035
012, 013, 030, 032
013, 048
018, 031
008, 033
033
018
029
035
[008]z, 014
035
035
014, 061
061
035
035
059
032
018, 029, 030, 031, 032
032
016, 017, 018, 029
018, 029
031, 032
031
035
008, 033
031
021
008, 021, 022, 025, 028, 032
013, 031
018, 029, 032
031
032
035
032
008, 013, 025, 029, 030,
031, 032, 033, 062
N
O
P
Q
R
MGA
MGN Technology
Microsoft
Mind
Minolta
Mitsubishi
Motorola
MTC
Multitech
NEC
Nikko
Niveus Media
Noblex
Northgate
Olympus
Optimus
Optonica
Orion
Panasonic
Penney
Pentax
Philco
Philips
Philips Magnavox
Pilot
Profitronic
Pulsar
Quarter
Quartz
Quasar
RadioShack
Radio Shack/
Realistic
Radix
Randex
RCA
Realistic
ReplayTV
Ricavision
Runco
S
Samsung
Sanky
Sansui
Sanyo
Scott
Sears
Sharp
Shogun
Singer
Sonic Blue
010, 013
013, 030
035
035
014
010, 038
032
008, 013, 030
008, 030, 033
018, 029
031
035
013, 030
035
032
021, 031
024
044, 062
000, 001, 002, 003, 004,
032, 060
013, 014
014
032
024, 032, 041, 061
041
031
013
025
029
029
032
008, 024, 031
024, 029, 030, 031, 032, 033
031
031
011, 012, 013 ,014, 015,
030, 032, 051
008, 024, 029, 030, 031,
032, 033
060
035
025
013, 019, 020, 030, 040,
048, 049, 061
025
008, 044, 062
013, 029, 030
010, 019
008, 014, 029, 031, 032
023, 024, 042
013, 030
032
060
Sony
Stack
STS
Sylvania
T
Symphonic
Systemax
Tagar Systems
Tandy
Tashiko
Teac
Technics
Teknika
Thomas
Tivo
TMK
Toshiba
U
V
W
X
Y
Z
Totevision
Touch
Unitech
Vector
Vector Research
Video Concepts
Videosonic
Viewsonic
Villain
Voodoo
Wards
XR-1000
Yamaha
Zenith
ZT Group
005, 006, 007, 008, 026
,034, 035, 036, 037, 045 ,
052, 053, 054
035
014, 032
008, 010, 021, 022, 032,
033, 046, 055
008, 021, 022, 033
035
035
029
031
008, 033
032
008, 031, 032, 033
008
061
013, 030
009, 010, 019, 035, 039,
047, 050, 057
013, 030, 031
035
013, 030
019
018
018, 019
013, 030
035
008
035
008, 013, 014, 024, 030,
031, 032, 033
008, 032, 033
018, 029
008, 025, 026, 027, 043
035
TV/DVD/VCR Combination
M
P
T
T
Broksonic
CineVision
Go Video
Insignia
Panasonic
Samsung
Sony
Sylvania
Toshiba
056
058
048
059
002, 003, 004
040, 048, 049
037, 045, 052, 053, 054
046
039, 050, 057
Satellite Receiver
A
C
D
E
G
H
I
J
L
M
TV/VCR Combination
R
S
RCA
Sylvania
051
055
022
001
047
DEVICE SELECT : SAT/CBL
DVD/VCR Combination
B
C
G
I
P
S
Magnavox
Panasonic
Toshiba
N
P
AccessHD
Alpha Digital
Alphastar
Artec
CaptiveWorks
Channel Master
Chaparral
Coolsat
Coship
Crossdigital
Digital Stream
109
109
083
106
102
111
077
103
114
120
110
058, 059, 060, 061, 062, 063,
064, 068, 069, 073, 074, 075,
DIRECTV
076, 088, 089, 090, 093,
095, 116
052, 053, 054, 055, 065, 091,
Dish Network
115, 119
Dishpro
115, 119
Drake
078
Echostar
052, 065, 091, 115, 119
Expressvu
119
GE
056, 057, 112
General Instrument 079, 117
GOI
119
Goodmind
112
Hisense
118
Hitachi
074, 084
HTS
119
Hughes Network
060, 062, 067, 068, 070,
Systems
075, 093
Humax
104
Ilo
118
Insignia
096
Jerrold
117
JVC
052, 065, 091, 119
Lasonic
113
LG
096, 105
Magnavox
073, 107
Memorex
073
MicroGem
108
Mitsubishi
068, 099
Motorola
117
Next Level
117
Panasonic
061, 095, 097
R
Pioneer
Primestar
Proscan
Proton
RadioShack
RCA
S
T
U
V
Z
Realistic
Samsung
Sharp
Sony
Star Choice
STS
Tivax
Tivo
Toshiba
UltimateTV
Uniden
US Digital
Viewsat
Voom
Zenith
F
G
H
J
Jerrold
L
M
B
C
D
E
ABC
Adelphia
Americast
Antronix
Archer
AT&T
Bell South
Cable Vision
Cabletenna
Cableview
Clearmaster
ClearMax
Colour Voice
Comcast
Comtronics
Contec
Coolmax
COX
Daeryung
Director
Dumont
Eastern
[009]z, 010, 012, 028, 040
007
047
014, 015
015
003
047
006
014
013
046
046
016
000, 005, 033
017
018
046
005
036
033
051
019
LG
Magnavox
MegaCable
Memorex
Motorola
N
O
P
Cable TV
A
Everquest
Focus
GC Electronics
GE
Gehua
Gemini
General Instrument
Goldstar
Hamlin
Hitachi
Jasco
Q
R
S
Movie Time
Multitech
NEC
NET Brazil
NSC
Oak
Pace
Panasonic
Paragon
Philips
Pioneer
Popular Mechanics
Proscan
Pulsar
Quasar
RadioShack
RCA
Realistic
Recoton
Regal
Regency
Rembrandt
Runco
Samsung
Scientific Atlanta
Signal
Signature
Sony
Sprucer
Standard
Component
Starcom
Stargate
Starquest
041
045
015
009, 010
033
020, 041
005, 010, 033, 044
042
021
010
041
005, 010, 020, 028, 029, 033,
041, 044
050
022
005
023, 040
000, 003, 005, 033, 037,
039, 044
024
046
011
035
024
018
008, 043
026, 027, 040
040
016, 022
002, 030, 036, 042
045
009, 010
040
040
041, 046
013, 027
015
045
021
019
010
040
008, 034, 042
001, 002, 003, 007, 012,
036, 038
020, 041
010
006, 048
027
025
020, 028, 041
020, 041
020, 041
T
U
V
Z
Supercable
Supermax
Time Warner
Tocom
Torx
Toshiba
Trans PX
Tristar
TS
Tusa
TV86
Unika
United Cable
Universal
V2
View Star
Viewmaster
Vision
Vortex View
Zenith
Zentek
044
046
004
031
049
040
044
046
049
020, 041
024
014, 015
028
014, 015
046
018, 022, 024
046
046
046
032, 040, 047
045
N
O
P
Q
R
S
DEVICE SELECT : CD
CD Player
A
B
C
D
G
H
J
K
L
L
M
Accuphase
Acoustic Research
ADS
Aiwa
Akai
Audio Alchemy
Audio Pro
Audio-Technica
B&K
California Audio
Labs
Carver
Denon
DKK
DMX Electronics
Dynamic Bass
GE
Genexxa
Harman/Kardon
JVC
Kenwood
Krell
Linn
Magnavox
Marantz
Miro
018
019
020
021
022
023
024
025
026
036
040, 041
001, 042, [111]z
035
040
041
017
037
007
003, 011, 012
038, 039
040
040
027
028
035
T
W
Y
Z
Mission
Musical Fidelity
NEC
NSM
Onkyo
Optimus
Philips
Pioneer
Polk Audio
Proscan
Proton
QED
Quad
RCA
Realistic
Rotel
SAE
Sansui
Sanyo
SAST
Sharp
Silsonic
Sonic Frontiers
Sony
Soundesign
Symphonic
TAG McLaren
Technics
Wards
Yamaha
Zonda
040
029
030
040
002
035, 037, 039, 041
009, 010
006
040
017
040
040
040
000, 017
041
040
040
040
031
040
032
038
040
004, 005, 008, 013, 014
033
034
040
015
040
016
040
DVD preset codes / Codes préréglés DVD
111
(default / default)
DVD-900
DVD-700
DVD-1000
DVD-1400
DVD-1500
DVD-1710
DVD-1720
DVD-1730
DVD-1740
DVD-1910
DVD-1920
DVD-1930
DVD-1940
DVD-2200
DVD-2800
DVD-2800g
014
DVD-2900
DVD-2910
DVD-2930
DVD-3800
DVD-3910
DVD-3930
DVD-A11
DVD-A1XV
DVD-A1
DVD-800
DVD-1600
DVD-2000
DVD-2500
DVD-3000
DVD-3300
Blu-Ray preset codes /
Codes préréglés Blu-Ray
e Model No. /
Modéle numéro
Philips
100
073
111
107
060, 067, 068, 070, 072,
073, 090
060
082
056, 057
118
117
056, 057, 058, 070, 076, 086,
087, 088, 089, 092
080
060, 062, 069, 070, 071, 094
098
059, 066, 116
117
085
109
060, 070
063
116
073, 081
118
101
117
064, 096
eM
odel No. / Modéle numéro
Pansat
Paysat
PCT
Philco
121
DVD-1800BD
DVD-2500BT
DVD-3800BD
DVD-A1UDCI
[ ]* :Preset codes set upon shipment from
the factory.
*[ ] :Les codes préréglés diffèrent en fonctiom
des livraison de l’usine.
PRESET CODE
www.denon.com
D&M Holdings Inc.
Printed in China 5411 10250 005DA