Wiznet WIZ-Embedded WebServer User manual

WIZ-600Wi User Manual
(Ver. 1.0)
©2007 WIZnet Inc. All Rights Reserved.
For more information, visit our website at www.wiznet.co.kr
WIZ-600Wi User Manual
WIZnet’s Online Technical Support
If you have something to ask about WIZnet Products, Write down your question on Q&A
Board in WIZnet website (www.wiznet.co.kr). WIZnet Engineer will give an answer as soon
as possible.
2
Technical Support: support@wiznet.co.kr
Sales & Distribution: sales@wiznet.co.kr
For more information, visit our website at http://www.wiznet.co.kr
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
Table of Contents
1.
2.
3.
4.
Overview ....................................................................................................5
1.1.
Main Functions ....................................................................................5
1.2.
Specification .......................................................................................6
1.3.
Products Contents (WIZ-600Wi-EVB) ...........................................................7
WIZ600Wi Module........................................................................................8
2.1.
Module Configuration ...........................................................................8
2.2.
Configuration Menu ............................................................................ 16
WIZ600Wi Hardware Specification ................................................................ 30
3.1.
Usable Channel ................................................................................. 30
3.2.
Dimension ........................................................................................ 31
3.3.
Connector ........................................................................................ 32
WIZ600Wi Base board ................................................................................ 34
4.1.
Description of base board ................................................................... 34
4.2.
Base Board Dimensions ...................................................................... 35
5.
Serial Converter Operation Test ................................................................... 36
6.
Warranty .................................................................................................. 42
Tables
Table 1. Specification ................................................................................... 7
Table 2. Products Contents ............................................................................. 7
Table 3. Channel for 802.11b/g mode .............................................................. 30
Table 4. Electrical Characteristics ................................................................... 30
Table 5. J9 Pin Description : MII Interface & Ethernet PHY Analog ............................. 32
Table 6. Pin Description : GPIO ...................................................................... 32
Table 7. Pin Description : UART & Factory Defalut> .............................................. 32
Table 8. Pin Descriptions : Ethernet PHY Analog Signal& Wireless LED ........................ 33
© Copyright 2008 WIZnet Inc. All rights reserved
3
WIZ-600Wi User Manual
FIGURES
Figure 1. Checking & Changing IP address of PC .................................................... 8
Figure 2. Searching Wireless Network ................................................................ 9
Figure 3. WIZ600Wi Log-in Screen ................................................................... 10
Figure 4. WIZ600Wi Log-in Completion Page....................................................... 11
Figure 5. Configuration Tool – System Information and Network Configuration .............. 12
Figure 6. Configuration Tool – Configuration Change ............................................. 16
Figure 7. Configuration Tool – Network ............................................................. 19
Figure 8. Configuration Tool – DHCP Server ........................................................ 20
Figure 9. Configuration Tool – Port Forward ....................................................... 21
Figure 10. Configuration Tool – Access Ctl.......................................................... 22
Figure 11. Configuration Tool – Security_WEP ..................................................... 23
Figure 12. Configuration Tool – Security_WPA ..................................................... 24
Figure 13. Configuration Tool – System ............................................................. 26
Figure 14. Configuration Tool – Administrator ..................................................... 27
Figure 15. Configuration Tool – F/W Upgrade ...................................................... 28
Figure 16. Configuration Tool – Log.................................................................. 29
Figure 17. WIZ600Wi Module Dimension ............................................................ 31
Figure 18. WIZ600Wi Connector Description ....................................................... 32
Figure 19. WIZ600Wi Base Board..................................................................... 34
Figure 20. WIZ600Wi Base Board Dimensions ...................................................... 35
Figure 21. Serial Converter Block Diagram ......................................................... 36
Figure 22. Configuration Tool – Use Serial Converter ............................................. 37
Figure 23. Device Terminal Program - Configuration ............................................. 38
Figure 24. Device Terminal Program – Input Serial Data ......................................... 39
Figure 25. Device Terminal Program – Send Serial Data .......................................... 40
Figure 26. Device Terminal Program – Input Network Data ...................................... 40
Figure 27. Device Terminal Program – Send Network Data ...................................... 41
© Copyright 2008 WIZnet Inc. All rights reserved
4
WIZ-600Wi User Manual
1. Overview
WIZ-600Wi is 2.4GHz IEEE802.11b/g based wireless device that is used for embedded systems.
WIZ-600Wi supports not only MII but also RS232C interface that enabling “Serial-to-Wireless”
functions. By using WIZ-600Wi, embedded access point cab be implemented.
1.1. Main Functions
„
Supports IEEE 802.11 b/g
„
Supports 54Mbps wireless LAN and 10/100Mbps Fast Ethernet
„
Supports 4/128/152Bit WEP Encryption
„
Supports WPA
„
User Filtering by using MAC address (ACL)
„
IEEE802.1x that supports EAP certification
„
Compatibility between wireless devices
„
Provides simple and user-friendly interface
„
Independent operation from main system
„
RS232 & Ethernet Interface
„
Supports AP, AP Client & Repeater
„
Available of implementing wireless function without changing the hardware of existing
system
„
Simple Configuration by using web-based AP utility
„
Dynamic IP Configuration by using DHCP server / client
„
Supports Multiple SSID & VLAN
„
Supports Serial to Wireless function (RS232c)
© Copyright 2008 WIZnet Inc. All rights reserved
5
WIZ-600Wi User Manual
1.2. Specification
< SOFTWARE >
Item
Operation mode
Specification
IEEE802.11b/g Access Point, Repeater, Client-bridge mode supported
Radio Enable/Disable, SSID Hidden, Multi SSID, Auto Channel Select,
Wireless
6
Rate Control (Include Auto mode), TX Power Control, Fragment Length,
RTS/CTS Length, Short & Long Preamble, Super A/g Adaptive Radio,
Beacon Interval, DTIM Period
WPA, WPA2.0(with Radius Server or Pre-Shared Key), AES and/or TKIP,
Security
Unicast Encryption: 802.1x Authentication, WEP Encryption, Packet Filtering,
MAC Address Filtering/Limiting, (NetBIOS/NetBEUI Filtering, DHCP Filtering)
Port
Network
Forwarding
(UDP,
TCP
or
Both
Protocol
Support),
DHCP
Client/Server/Relay,
WDS(Wireless Distribution System) Supported, NAT, DNS Server Setting
LAN: IP, Subnet, Gateway, WAN: IP, Subnet, Gateway, VLAN
Administrator ID/PWD, Device Name, Station & AP Assoc Information,
Management
System Information, SNMP v1/v2 (MIB-II, ieee802dot11), Telnet Server Support
Web-based Configuration, Upgrade through HTTP/TFTP,
Event Log (WEB Interface), RS232 Console Support
< HARDWARE >
Item
Specification
Standard
IEEE 802.11b/g, IEEE802.3 10/100Mbps Ethernet
Modulation
DBPSK, DQPSK, CCK, OFDM
Frequency
2.400~2.483 GHz
Available
Spectrum
83.5 MHz
Channels
13ch (1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13)
Data Rate (Mbps)
1,2,5.5,11, 6,9,12,18,24,36,48,54
Out Power
18 dBm
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
Sensitivity
1M: -94dBm, 54M: -68dBm
Operating Range
Indoor: 100 m, Outdoor: 400m
Interface
Ethernet 10/100 1 Port, UART, Factory Reset , Wireless Link/Activity LED,
Ethernet Link LED, Two Antenna Port (Rx Diversity)
Power
DC3.3V (Pin header Type)
Power (Internal)
3.3V,
Temperature
Storage: -20°C ~ +65°C
Range
Operating: -0°C ~ +55°C
Humidity
10% ~ 90% (Non-Condensing)
2.85V, 1.8V
7
Table 1. Specification
1.3. Products Contents (WIZ-600Wi-EVB)
Item
EVB B/D
WIZ600Wi Module (Plugged in Base Board)
1
WIZ600Wi Base Board
1
Power Adaptor (DC 5V/2A)
1
Antenna
Accessory
Quantity
Option
Software CD
1
UTP Cable
1
Serial Cable
1
Table 2. Products Contents
☞ Antenna is optional item. Please specify the detail when placing the order.
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
2. WIZ600Wi Module
2.1. Module Configuration
2.1.1.
Connecting Web Browser
WIZ-600Wi configuration can be processed though web browser. As default IP address of
WIZ600Wi is ‘192.168.1.254’, the IP address of PC should be changed as ‘192.168.1.x’ for normal
8
connection.
The default log-in information is <username : admin> & <password : admin>.
The connection process is as below.
STEP 1>
<When connecting through Ethernet>
Checking IP address of PC (Control Panel -> Network and Internet Connections -> Local Area
Connections -> Internet Protocol (TCP/IP) )
<When connecting through Wireless Lan>
Checking IP address of PC (Control Panel -> Network and Internet Connections -> Wireless
Network Connections -> Internet Protocol (TCP/IP) )
Figure 1. Checking & Changing IP address of PC
STEP 2> Plug the WIZ600Wi module in the base board, and connect the Lan cable and power
adaptor. Be sure to check if input power is DC5V before supplying the power.
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
STEP 3> In case of connecting through Ethernet, skip the step 3. When connecting through
wireless LAN, connect to the network of which SSID is ‘wiznet’.
9
Figure 2. Searching Wireless Network
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
STEP 4> After 1 minute later, input the address http://192.168.1.254 at the web browser. When
connecting through wireless LAN, if connection is not normally processed, disable the wired
network connection at the Control Panel, and try the connection again.
10
Figure 3. WIZ600Wi Log-in Screen
STEP 5> If you input ‘admin’ in the Username and Password, you can go to the configuration
page. The default value of both Username and Password is ‘admin’. After changing them, you
should input changed value. If you forget the Username and Password, you can initialize the
module to the factory default by pushing Factory_default button for more than 10 seconds.
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
STEP 6> If log-in is normally processed, below configuration page is appeared.
11
Figure 4. WIZ600Wi Log-in Completion Page
2.1.2. System Information and Network Configuration
The configuration page of WIZ600Wi is composed of as below figure.
The page can be divided into menu and its contents. The contents window is displayed according
to selection of menu.
Menu window is composed of System Information, Configuration and Firmware Upgrade.
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
12
s
Figure 5. Configuration Tool – System Information and Network Configuration
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
2.1.3. System Info
This is the menu to check WIZ600Wi’s information showing system and wired & wireless
information.
System Info
System Info is selected, below information of WIZ600Wi can be checked.
13
à SYSTEM INFORMATION
-
AP Name: Displaying the name of AP
-
User Name : Displaying the ID of current user of AP
-
AP Version : Displaying the current version of AP
à WIRELESS INFORMATION
-
AP Status : Displaying if AP mode is enabled or not.
-
SSID : Displaying current SSID.
-
SSID Hide : Displaying SSID Hide mode is enabled or not.
-
Channel : Displaying channel number currently set
-
Wireless Mode : Displaying wireless mode set as 802.11b or 802.11g.
-
Tx Rate : Displaying currently set wireless transmission rate
-
TX Power : Displaying currently set wireless output power.
-
MAC Address : Displaying MAC address of the AP.
-
Frequency : Displaying currently set frequency.
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
-
RTS/CTS : Displaying the value of RTS/CTS.
-
Fragmentation : Displaying Fragmentation value.
-
Link Quality: Displaying wireless connection quality.
-
Signal level : Displaying current signal level.
-
Noise level : Displaying current noise level.
14
à NETWORK INFORMATION
- IP Mode : Displyaing IP mode that the AP is using (Fixed IP or DHCP)
- IP Address : Displaying LAN IP set for the AP
- Subnet Mask : Displaying Subnet mask set for the AP
- Gateway : Displaying Gateway set for the AP
- DNS Server1 : Displaying the first DNS set for the AP
- DNS Server2 : Displaying the second DNS set for the AP
- MAC Address : Displaying MAC address set for the AP
à NAT INFORMATION
- Use NAT: Displaying ‘Use NAT’ is enabled or not
- LAN IP Address : Displaying the IP address when ‘Use NAT’ is enabled
- Subnet Mask : Displaying the subnet mask when ‘Use NAT’ is enabled
- MAC Address : Displaying MAC Address of AP
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
à DHCP SERVER INFORMATION
- Use DHCP Server : Displaying ‘Use DHCP Server’ is enabled or not
- Start IP Address : Displaying ‘Start IP address’ assigned to DHCP server
- Last IP Address : Displaying ‘Last IP address’ assigned to DHCP server
- Subnet Mask : Displaying ‘Subnet Mask’ assigned to DHCP server
- Refresh Time : Displaying refresh time of IP re-assignment
2.1.4. Client List
If Client List menu is clicked, the station information connected to AP is displayed.
à ASSOCIATION LIST
-
MAC Address : Displaying the MAC address and the ID of station connected to
the AP
-
CH : Displaying connection channel between AP and station
-
RATE : Displaying transmission speed between AP and station
-
RSSI : Displaying RF power between AP and station
-
TX/RX : TX/RX : Displaying TX/RX data.
-
ERP : Displaying if use ‘802.11g Data rate’ or not
-
TYPE : Displaying security status
-
VLAN : Displaying VLAN use status
© Copyright 2008 WIZnet Inc. All rights reserved
15
WIZ-600Wi User Manual
2.2. Configuration Menu
You can change configuration value of all functions of WIZ600Wi. After completing the value
change, re-start the system by clicking System Re-boot button.
16
Figure 6. Configuration Tool – Configuration Change
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
2.2.1. Wireless
It configures wireless interface of AP.
à RADIO CONTROL
-
AP MODE : Configure as Enable for Access Point
à BASIC WIRELESS CONFIGURATION
-
Operation Mode
Operation mode can be configured after wired connection is established.
The connection can be closed at the wireless connection.
z
Access Point : WIZ600Wi operates as Access Point.
z
Station : WIZ600Wi operates as Station for the connection to another
access point.
z
-
Repeater : WIZ600Wi operates as Repeater
SSID Hide : This function hides SSID in the Beacon packet that Access point
sends for the security. If this function is enabled, the SSID is not shown when a
client searches the Access Point. However, if Client has the information of the
SSID and specifies it when searching Access point, it can search the Access Point.
-
Use VLAN : It configures VLAN Tag of related SSID.
-
SSID : It configures SSID of 2.4GHz wireless interface. The multi-SSID is
supported. You can use max 4 SSIDs.
-
Wireless Channel : It configures frequency that 2.4GHz wireless interface will
use. In case of Auto CH Select, the most suitable channel is selected after
searching the frequency.
-
Wireless Mode : It configures wireless mode that 2.4GHz wireless interface will
use. 2.5GHz wireless interface can configure 11g and 11b. If ‘Mixed 802.b/g
mode’ is selected, the wireless client supporting both of 11b and 11g, can
connect to AP.
If ‘802.11b only’ or ‘802.11g only’ is selected, the client
supporting each mode, can connect to the AP.
-
Tx Rate : It configures transmission speed. According to the mode, the speed
can be different. If ‘best’ is selected, AP automatically operates with the best
transmission speed.
-
Tx Power : It configures radio transmission output.
© Copyright 2008 WIZnet Inc. All rights reserved
17
WIZ-600Wi User Manual
à ADVANCED WIRELESS CONFIGURATION
18
-
MAX User : It configures user number from 1 to 24.
-
Beacon interval : It is the transmission interval of Beacon. Beacon contains the
information necessary for the communication including SSID.
-
DTIM Period : DTIM is used for Power Saving or Multicast/Broadcast. It can be
configured in the range of 1~255.
-
Fragment Length : Fragment is the unit of packet segmentation. It can be
configured in the range of 256 ~ 2346 Byte. If communication environment is
not good, lower value is more advantageous for the transmission.
-
RTS/CTS Length : It is the minimum size of the packet of CTS(Clear to Send)
signal responding to RTS (Request to Send) signal. It can be configured in the
range of 256 ~ 2346 Byte.
-
High Speed Rate : This is the function to transmit high-speed data. It is for the
best performance of the system.
-
Use AR : It continuously checks if smart antenna has any physical obstacles in
the home or office environment. If there is any obstacle, it controls radio signal
to prevent performance deterioration.
-
Short Preamble : Preamble is the signal to synchronize transmission timing
between two systems at the network communication. Long Preamble Type is the
default value. In here, it configures if Short Preamble Type is selected or not.
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
2.2.2. Network
It configures internal network of AP.
19
Figure 7. Configuration Tool – Network
à NAT CONFIGURATION
-
Use NAT : It configures ‘Use NAT’ is enabled or not.
à NETWORK CONFIGURATION
-
Network Mode
z
DHCP : When using dynamic IP address, select the ‘DHCP’.
As operating as
AP DHCP Client, it acquires IP address from DHCP server connected to
Internet line.
z
Static : When using fixed IP address, select the ‘Static’. User should manually
input IP address, subnet mask, gateway address & DNS address for AP.
-
LAN IP Address: When using NAT, configure LAN IP.
-
LAN Subnet Mask : When using NAT, configure LAN subnet mask.
-
Gateway : When using NAT, configure LAN gateway.
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
-
DNS Server 1 : The first DNS server address to be assigned to the server
-
DNS Server 2 : The second DNS server address to be assigned to the server
2.2.3. DHCP Server
This page configure DHCP server and Relay function of AP.
20
Figure 8. Configuration Tool – DHCP Server
à DHCP SERVER CONTROL : It selects if ‘DHCP MODE’ is enabled or not.
-Start IP Address : It configures ‘Start IP address” to be assigned to DHCP.
-Last IP Address : It configures ‘Last IP address’ to be assigned to DHCP.
-Subnet Mask : It configures Subnet Mask to be assigned to DHCP.
-Gateway : It configures Gateway address
-DNS Server: It configures DNS Server value.
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
2.2.4. Port Forward
Port Forward operates only in case of using NAT.
21
Figure 9. Configuration Tool – Port Forward
-
Use Port-Forwarding : It selects use of ‘port forwarding’ function.
-
Port Number : Input port number to be used for port-forwarding
-
Protocol : It selects the protocol to be used (TCP/UDP, TCP, UDP).
-
Destination IP : Input destination IP address
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
2.2.5. Access Ctrl
It configures AP access control.
22
Figure 10. Configuration Tool – Access Ctl
à MAC ACCESS CONTROL
It registers MAC address of Stations accessible to AP, and configures access allowance
of the Stations.
-
-
MAC Filter
z
Open : Allowing the connection from all MAC addresses
z
Allow : Allowing the connection from specified MAC addresses
z
Deny : Denying the connection from specified MAC addresses
z
Disable : Mac filter is not used.
MAC Address : Adding MAC address to be used for MAC Filter
à Packet Filter
It blocks the packet from the specified port.
-
Use Packet Filter : It configures if ‘Use Packet Filter’ is used or not.
-
Port (1-65535) : Input the port number to be blocked
-
Protocol : Select the protocol to be blocked
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
2.2.6. Security
It configures the security of connection to AP.
23
Figure 11. Configuration Tool – Security_WEP
à WIRELESS SECURITY MODE
- Security Mode : It selects WEP, WPA, or None(not used).
à SECURITY CONFIGUATION
-
Authentication : It selects Open, Shared, or Auto
„
Open : The authentication is not required between wireless networks.
„
Shared : It allows the connection between wireless devices using shared
key(WEP Key identification)
„
Auto : According to authentication method, the connection can be
established between wireless devices.
-
Default WEP Key : Select the WEP Key to be used for default from 1 to 4.
-
WEP Key Method(WEP Encryption Method) : Define the HEX(10/26/32 digits)
and ASCII(5/13/16 digits) to be used.
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
-
WEP KEY : It uses WEP security. Users manually configure the value of key, Key
Length and Key number. All values between AP and Station/Client are same, the
communication can be processed.
z
64 bit – 10 Hex value (“A~F”, “a~f”, “0~9”)or
5 ASCII characters “a~z”, “0~9”)
Ex) “0123456aef”, “test1”
z
128 bit - 26 Hex value (“A~F”, “a~f”, “0~9”) or
13 ASCII character (“a~z”, “0~9”)
Ex) “01234567890123456789abcdef”, “administrator”
z
152 bit – 32 Hex value (“A~F”, “a~f”, “0~9”) or
16 ASCII characters (“a~z”, “0~9”)
Ex) “01234567890123456789012345abcdef”, “administratoradm”
Figure 12. Configuration Tool – Security_WPA
▫ WIRELESS SECURITY MODE
-
Security Mode : WPA
▫ SECURITY CONFIGUATION
- WPA Mode : WPA, WPA-PSK, WPA2, WPA2-PSK, WPA-AUTO,
© Copyright 2008 WIZnet Inc. All rights reserved
24
WIZ-600Wi User Manual
WPA-AUTO-PSK중 선택하여 지정합니다.
- Cipher Type : It selects the type of WPA encryption - AUTO, WEP, TKIP, AES
-
Group Key Update Interval : Input interval value of Group Key update. The input
range is 30 ~ 1800 seconds. If you input ‘0’, the update is not processed.
-
Pass Phrase Key : It configures PassPhrase. When using the character, 8~63
characters are used. If you use Hexadecimal, be sure to use 64 characters.
-
802.1x : WPA is the abbreviation of Wi-Fi Protected Access, the wireless security
technology announced by Wi-Fi Alliance. WPA is based on the IEEE 802.11i
standard, TKIP(Temporal Key Integrity Protocol). The fixed encryption based on
WEP method is weak to the hacking. WPA is developed to resolve this problem.
As WPA changes encryption key whenever transmitting 10 Bytes, the hacking is
not allowed. It uses WAP security. By using authentication server, Passphrase is
received.
-
WPA-PSK : It uses WPA security. User should manually set the configuration
value. All the values of AP and Station should be matched for the communication.
-
RADIUS Server IP : It configures IP address of authentication server.
-
RADIUS Server Port: It configures the port of authentication server.
-
RADIUS Shared Secret : It configures shared secrete key of authentication server.
© Copyright 2008 WIZnet Inc. All rights reserved
25
WIZ-600Wi User Manual
2.2.7. System Configuration
26
Figure 13. Configuration Tool – System
à MANAGEMENT CONFIGURATION
It configures use of Web Server and Telnet.
à SNMP CONFIGURATION
-
Use SNMP : It configures use of SNMP function.
-
SNMP Manager IP : It configures IP address of SNMP management server.
-
Set community : It configures community value to save the SNMP MIB value of
Access Point at the SNMP MIB browser.
-
SNMP Browser IP : It configures IP address of SNMP Browser server.
-
Get Community : It configures community value to acquire SNMP MIB value of
Access Point at the SNMP MIB browser.
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
à
UART(RS232) CONFIGURATION
-
Use Serial Converter : It selects using RS232 data transmission mode or not.
-
Operation Mode : RS232 data transmission should be processed through server
and client type. If one side operates as server, the other side does as client.
-
Server IP : When operated as Client mode, input server IP address. At the server
mode, this value is ignored.
-
TCP Port : Input TCP port number for data transmission. The same value should
be applied for both of server and client.
-
Use Flow Control : It selects ‘Use Flow Control’ for RS232 communication.
-
Baud rate : It configures baud rate for RS232 communication.
-
Data Bit : It configures data bit
-
Parity : It configures parity value
2.2.8. Administrator
Figure 14. Configuration Tool – Administrator
à USER CONFIGURATION
It configures AP name, user ID and password.
-
AP Name : It configures the name of current AP.
-
User Name : It configures User ID to be connected to the AP.
-
Password : It configures User Password to be connected to the AP.
© Copyright 2008 WIZnet Inc. All rights reserved
27
WIZ-600Wi User Manual
2.2.9. Firmware Upgrade
28
Figure 15. Configuration Tool – F/W Upgrade
à TFTP Server
-
Firmware Version : It displays current firmware version.
-
File Name : Input file name of Firmware.
-
TFTP Server IP : Input TFTP server IP.
-
File Downloading : Download the file from TFTP server.
* If there is the fail message of file downloading, check the file name and TFTP IP
address.
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
2.2.10. Log
It is used for checking log data of AP. Maximum 250 logs can be printed out, and max 500 logs
can be saved.
29
Figure 16. Configuration Tool – Log
- LOG Control : It configures log number to be printed out.
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
3. WIZ600Wi Hardware Specification
3.1. Usable Channel
3.1.1. Channel for 802.11b/g mode
Channel NO.
Channel Frequency (MHz)
Regulator Domain
1
2412
FCC/WORLD/TELEC
2
2417
FCC/WORLD/TELEC
3
2422
FCC/WORLD/TELEC
4
2427
FCC/WORLD/TELEC
5
2432
FCC/WORLD/TELEC
6
2437
FCC/WORLD/TELEC
7
2442
FCC/WORLD/TELEC
8
2447
FCC/WORLD/TELEC
9
2452
FCC/WORLD/TELEC
10
2457
FCC/WORLD/TELEC
11
2462
FCC/WORLD/TELEC
12
2467
WORLD/TELEC
13
2472
WORLD/TELEC
14
2484
TELEC
Table 3. Channel for 802.11b/g mode
3.1.2. Electrical Characteristics
1. Power consumption
Typical 500mA(Max 700mA) at 3.3V
2. Operating Voltage
3.3V ± 0.2V
Table 4. Electrical Characteristics
© Copyright 2008 WIZnet Inc. All rights reserved
30
WIZ-600Wi User Manual
3.2. Dimension
◙
Bottom View
31
◙
Side View
7mm
Shield can
Heat sink
Figure 17. WIZ600Wi Module Dimension
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
3.3. Connector
BOTTOM Layer
J2 : 2mm Pitch, Male, 1x5
32
J7 : 2mm Pitch, Male, 1x10
J10 : 2mm Pitch, Male, 1x5
J9 : 1.27x1.27, SMD, Male, 2x14
Figure 18. WIZ600Wi Connector Description
No.
Signal
No.
Signal
1
3.3V
2
3.3V
3
RXC
4
/RESET
5
TXD2
6
TXC
7
RXD1
8
TXD0
9
RXD0
10
TXD1
11
RXDV
12
TXD2
13
CRS
14
TXD3
15
RXERR
16
TXEN
17
MDC
18
COL
19
MDIO
20
GND
21
GND
22
PWFBOUT
23
RX+
24
TX+
25
RX-
26
TX-
27
GND
28
GND
Table 5. J9 Pin Description : MII Interface & Ethernet PHY Analog
No.
Signal
No
Signal
1
GPIO2
2
GPIO4
4
GPIO1
5
GND
No.
Signal
No.
3
Signal
GPIO3
Table 6. Pin Description : GPIO
No.
Signal
No
Signal
1
GND
2
SOUT (CMOS Level)
4
3.3V
5
GPIO6
No.
3
Signal
SIN (CMOS Level)
Table 7. Pin Description : UART & Factory Defalut>
No.
Signal
No
© Copyright 2008 WIZnet Inc. All rights reserved
Signal
No.
Signal
WIZ-600Wi User Manual
1
RX-
2
RX+
3
TX-
4
TX+
5
PWFBOUT
6
GND
7
GND
8
GPIO7
9
3.3V
10
3.3V
Table 8. Pin Descriptions : Ethernet PHY Analog Signal& Wireless LED
# GPIO2 : Ethernet Link (Active High)
# GPIO6 : Factory Default (Active High)
# GPIO7 : WLAN ACT (Active High)
© Copyright 2008 WIZnet Inc. All rights reserved
33
WIZ-600Wi User Manual
4. WIZ600Wi Base board
WIZ600Wi Base Board is the board for testing the WI600Wi module. It is composed of serial port,
LAN port, reset switch and LED.
4.1. Description of base board
WLAN_ACT
Ethernet_LINK
Factory_default
34
DB9 for USART
(male)
RJ45 for wired LAN
(with transformer)
Power Switch
DC 5V Input
Figure 19. WIZ600Wi Base Board
z
Ethernet_LINK : It is the LED to display the connection status of wired LAN. The LED
blinks when connection is established with external device and turns off when connection
is closed.
z
WLAN_ACT : It is the LED to display the ACT of wireless LAN. LED keeps lightening in
normal time, and turns off at the occurrence of ACT. If data is frequently transferred, LED
operates as flickering.
z
Factory_default : It is the switch for module initialization. It is initialized to factory default
by pressing for 10 seconds. If you press it instantly, it operates as general reset switch.
z
DB9 : It is the 9pin D-SUB connector for USART IN & OUTPUT. It can be utilized for
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
testing Serial-to-Ethernet function of the module.
RJ45 : LAN cable is connected. It connects the PC or HUB to the module. Both of direct
z
and cross-over cable are used.
z
Power Switch : It is the switch for power ON/OFF.
z
DC 5V Input : It is connected to power adaptor. The power adaptor should be more than
1A standard.
4.2. Base Board Dimensions
13.00
67.00
75.00
78.60
1.00
8.20
35
Figure 20. WIZ600Wi Base Board Dimensions
z Connection Requirement : Power(J8), Audio Output(CON1), RJ45(U5)
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
5. Serial Converter Operation Test
Serial-to-Wireless function can be implemented by using ‘Serial Converter’ function. In this
manual, the testing will be performed by using PC supporting wireless LAN and serial port. Device
Terminal program is used for checking data communication. Device Terminal program can be
downloadable at the WIZnet Homepage (http://www.wiznet.co.kr)
36
Figure 21. Serial Converter Block Diagram
STEP 1> Plug the WIZ600Wi module into the base board and connect the serial cable and power
adaptor. In this test, serial cable is connected to PC. When connecting to another serial device, the
serial cable will be connected to the device.
STEP 2> After more than one minute for the booting, connect to the module through web
browser to enable ‘Serial Converter’ function. In chapter 2.1, the connecting method through web
browser is described in detail.
STEP 3> Click ‘System’ menu, and check ‘Use Serial Converter’ of UART CONFIGURATION. In this
testing, the module is configured as below,
-
IP address : 192.168.1.200
-
Serial Baud Rate : 9600bps
For the detail, refer to the <Figure 22>
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
37
Figure 22. Configuration Tool – Use Serial Converter
STEP 4> Execute ‘Device Terminal’ program included in the CD. ‘Device Terminal’ is the
combination program of serial terminal and network socket connection programs. It is developed
for more convenient test of serial to Ethernet. Configure the IP address and serial baud rate
according to the value of WIZ600Wi set in the STEP 3. If serial port of the testing PC is occupied
by another program, it can cause abnormal operation of Device Terminal program.
Device Terminal program is composed of upper Serial Terminal and lower Network Terminal. After
configuring serial, click “Open’ & buttons for program operation.
The module is configured as server mode at the ‘STEP3’. Input the module address ‘192.168.1.200’
for IP address and ‘6565’ for the Port in the network terminal window. Click ‘Connect’ button for
the connection with module. If connection is completed, the status information ‘Connected :
192.168.1.200:6565’ is displayed in the lower part of the program.
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
38
.
Figure 23. Device Terminal Program - Configuration
STEP 5> If connection is completed, perform the data transmission test. In order to test the data
transmission from serial to Ethernet, input any data in the upper window of Device Terminal
program.
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
39
Figure 24. Device Terminal Program – Input Serial Data
STEP 6> If you click ‘Send’ button after inputting serial data, the data will be displayed in the
lower window of the program as shown in <Figure 25>. If you can see the data is correctly
displayed, it means the serial data is normally transmitted to WIZ600Wi, and received through
wireless LAN.
STEP 7> In the STEP 7, we will perform the testing to transmit the data from wireless to the serial.
Input the data in the lower window of the program as shown in <Figure 26>
.
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
①Click
②Display received data
Figure 25. Device Terminal Program – Send Serial Data
Figure 26. Device Terminal Program – Input Network Data
© Copyright 2008 WIZnet Inc. All rights reserved
40
WIZ-600Wi User Manual
STEP 8> Click ‘Send’ button after inputting the data in the network terminal. If data is normally
transmitted, received data is displayed in the upper serial terminal window.
②Display received data
41
①Click
Figure 27. Device Terminal Program – Send Network Data
© Copyright 2008 WIZnet Inc. All rights reserved
WIZ-600Wi User Manual
6. Warranty
WIZnet Co., Ltd offers the following limited warranties applicable only to the original purchaser.
This offer is non-transferable.
WIZnet warrants our products and its parts against defects in materials and workmanship under
normal use for period of standard ONE(1) YEAR for the WIZ110SR board and labor warranty after
the date of original retail purchase. During this period, WIZnet will repair or replace a defective
products or part free of charge.
Warranty Conditions:
1.
The warranty applies only to products distributed by WIZnet or our official distributors.
2.
The warranty applies only to defects in material or workmanship as mentioned above in
6.Warranty. The warranty applies only to defects which occur during normal use and does
not extend to damage to products or parts which results from alternation, repair,
modification, faulty installation or service by anyone other than someone authorized by
WIZnet Inc. ; damage to products or parts caused by accident, abuse, or misuse, poor
maintenance, mishandling, misapplication, or used in violation of instructions furnished by
us ; damage occurring in shipment or any damage caused by an act of God, such as
lightening or line surge.
Procedure for Obtaining Warranty Service
1.
Contact an authorized distributors or dealer of WIZnet Inc. for obtaining an RMA (Return
Merchandise Authorization) request form within the applicable warranty period.
2.
Send the products to the distributors or dealers together with the completed RMA
request form. All products returned for warranty must be carefully repackaged in the
original packing materials.
3.
Any service issue, please contact to sales@wiznet.co.kr
© Copyright 2008 WIZnet Inc. All rights reserved
42