Craftsman 320.10320 Operator`s manual

Operator's
ManuaU
16.O°VOLT L_THHUM-.HONCORDLESS
3/8=Jno DrilHIDtivet
Model No.
320.10320
° WARRANTY
o SAFETY
= ASSEMBLY
° DESCRIPTION
° OPERATION
o MAINTENANCE
A_k WARNING:
To reduce the risk
of injury, the user must read and
understand the operator's manual
before using this product°
CHARGE BATTERY
BEFORE FIRST USE
Sears, Roebuck and Co., Hoffman Estates, tL 60179 USA
Visit the Craftsman web page: wwwsears.com/craftsman
Save this manual for future
reference
ONE YEAR FULL WARRANTY
ON CRAFTSMAN
TOOL
If this Craftsman tool fails to give complete satisfaction within one year from the date of purchase,
return it to any Sears store or parts & repair center or other craftsman outlet in the United States
for free repair (or replacement, if repair proves impossible)°
This warranty does not include expendable parts such as lamps, batteries, bits, or blades.
This warranty applies for only 90 days from the date of purchase if this product is ever used for
commercial or rental purposes
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
Sears, Roebuck and Co. Hoffman Estates IL 60179
SAVE THESE INSTRUCTIONS!
READ ALL INSTRUCTIONSt
This Drill/Driver has many features for making its use more pleasant and enjoyable. Safety,
performance and dependability have been given top priority in the design of this product making
it easy to maintain and operate.
,_k WARNING: Some dust created by using power tools contains chemicals known to the state
of California to cause cancer and birth defects or other reproductive harm°
Thepurposeofsafetysymbolsis toattractyourattentionto possibledangers.Thesafety
symbolsandtheexplanations
withthemdeserveyourcarefulattentionandunderstanding.
The
symbolwarningsDONOTbythemselves
eliminateanydanger..
Theinstructions
andwarnings
theygivearenosubstitutes
forproperaccidentprevention
measures.
,_WARNUNG:
BE SURE to read and understand all safety alert symbols such as
"DANGER", "WARNING" and "CAUTION" BEFORE using this product. Failure to follow all
instructions may result in electric shock, fire andlor serious personal injury.
SYMBOL
SRGNAL
MEANING
DANGER:
situation,
if not avoided,
will resuIt
Indicates which,
an imminently
hazardous
in death or serious injury.
WARNIING;
situation,
if not avoided,
Indicates which,
a potentially
hazardouscould
result in death or serious injury_
CAUTION-"
situation,
Indicates which,
a potentially
if not avoided,
hazardousmay result
in minor or moderate injury_
CAUTmON--
(Without Safety Alert Symbol) Indicates
a situation that may result in property
damage
._kWARMaNG:To
ensure safety and reliability, al! repairs should
qualified service technician at Sears Service Center.
be performed
by a
•_WARNBNG-" The operation of any power tool can result in foreign objects
being thrown into your eyes, which can result in severe eye damage. Before
beginning power tool operation, always wear safety goggles or safety glasses
with side shields and a full face shield when needed. We recommend Wide
Vision Safety Mask for use over eyeglasses or standard safety glasses with side
shields. Always use eye protection which is marked to comply with ANSI Z87..1.
SAVE THESE
INSTRUCTllONS
Some of these following symbols may be used on this tool.. Please study them and learn their
meaning.. Proper interpretation of these symbols will allow you to operate the tool better and safer,_
SYMBOL
NAME
DESBGNATUOHIEXPLANATION
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency (cycles per second)
W
Watt
Power
rain
Minutes
,--.,.,
Alternating Current
Time
Type of current
Direct Current
Type or a characteristic
Rotational speed, at no load
no
No Load Speed
B
Class I! Construction
......
lmin
Per Minute
@
0
©
A
®
Wet Conditions
of current
Double-insulated
construction
Revolutions, strokes, surface speed,
orbits, etc, per minute
Do not expose to rain or use in damp
locations..
Alert
Read The Operator's
To reduce the risk of injury, user must
read and understand operator's manual
before using this producL,
Manual
Always wear safety goggles or safety
glasses with side shields and a full face
shield when operating this product..
Eye Protection
Safety Alert
Precautions that involve your safety,
No Hands Symbol
Failure to keep your hands away from the
blade will result in serious personal injury..
No Hands Symbol
Failure to keep your hands away from the
blade will result in serious personal injury..
No Hands Symbol
Failure to keep your hands away from the
blade will result in serious personal injury.
No Hands Symbol
Failure to keep your hands away from the
blade will result in serious personal injury,
To reduce the risk of injury or damage,
avoid contact with any hot surface.
Hot Surface
4
,_WARH!IHG:
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all
instructions listed below may result in electric shock, fire and/or serious personal injury.
The term "power tool" in all of the warnings listed below refer to mains-operated (corded)
power tools or battery-operated (cordless) power tools.
SAVETHESEINSTRUCTIONS
WORK AREA SAFETY
[] Keep work area clean and well lit. Cluttered or dark areas invite accidents
[] Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust° Power tools create sparks which may ignite the dust or
fumes
[] Keep children and bystanders away while operating a power tool. Distractions cause you
to lose control.
ELECTRICAL
SAFETY
[] Power tool plugs must match the outlet. Never modify the plug in any way. Do not use
any ChargerlAdapter
plugs with earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce the risk of electric shock
[] Avoid body contact with earthed (grounded) surfaces such as pipes, radiators, ranges
and refrigerators° There is an increased risk of electric shock if your body is earthed
(grounded).
[] Do not expose power tools to rain or wet conditions. Water entering a power tool wi!]
increase the risk of electric shock_
[] Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool Keep cord away from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
[] When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
[] Use battery only with Charger/Adapter
PACK
BATTERY
I
320.11208
I
listed.
CHARGER/ADAPTER
320.67099
320.10321
PERSONAL SAFETY
[] Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol
or medication. A moment of inattention while operating power tools may result in serious
person,al injury.
[] Use safety equipment. Always wear eye protection. Safety equipment such as dust masks,
non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will
reduce personal injuries.
[] Avoid accidental starting° Ensure the switch is in the off position before plugging in.
Carrying power tools with your finger on the switch or plugging in power tools that have the
switch on invites accidents
[] Remove any adjusting key or wrench before turning the power tool on. A wrench or key
left attached to a rotating part of the power tool may result in personal injury
[] Do not overreach. Keep proper footing and balance
control of the power toot in unexpected situations
at all times, This enables better
ml Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewelry or tong hair can be caught in moving parts.
_1 if devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of these devices can reduce dustrelated hazards.
[] Do not wear loose clothing or jewelry. Contain long hair. Loose clothes, jewelry or long
hair can be drawn into air vents°
[] Do not use on a ladder or unstable support. Stable footing on a solid surface enables
better control of the power tool in unexpected situations.
POWER TOOL USE AND CARE
[] Do not force the power tool. Use the correct power tool for your application_ The correct
power tool will do the job better and safer at the rate for which it was designated°
E Do not use the power tool if the switch does not turn it on or off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired_
[] Disconnect the plug from the power source andlor the batter pack from the power tool
before making any adjustments,
changing accessories or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool accidentally°
Im Store idle power tools out of the reach of children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users
II Maintain power tools. Check for misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the power tool's operation. If damaged,
have the power tool repaired before use. Many accidents are caused by poorly maintained
power tools°
[] Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
W Use the power tool, accessories
and tool bits etc., in accordance with these
instructions
and in the manner intended for the particular type of power tool, taking in
account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation
BATTERY TOOL USE AND CARE
[] Ensure the switch is in the off position before inserting battery pack. Inserting the
battery pack into power tools that have the switch on invites accidents_
[] Recharge only with the ChargerlAdapter
specified by the manufacturer.
A Charger/
Adapter that is suitable for one type of batter pack may create a risk of fire when used with
another battery pack°
[] Use power tools only with specifically designated
packs may create a risk of injury and fire.
battery
packs. Use of any other battery
[] When battery pack is not in use, keep it away from other metal objects like paper clips,
coins, keys, nails screws or other small metal objects that can make a connection from
one terminal to another. Shorting the battery terminals together may cause burns or a fire
[] Under abusive conditions, liquid may be ejected from the battery, avoid contact. If
contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause irritation or burns°
_WARHIHG:
To reduce the risk of injury, user must read instruction manual
SERVICE
[] Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power toot is maintained,
[] When servicing a power tool, use only identical replacement parts. Follow instructions
in the Maintenance section of this manual. Use of unauthorized parts or failure to follow
Maintenance instructions may create a risk of shock or injury_
[] Hold power tools by insulated gripping surfaces when performing an operation where
the cutting tool may contact hidden wiring or its own cord, Contact with a "live" wire will
also make exposed metal parts of the tool "live" and shock the operator
m Use clamps or another practical way to secure and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves it unstable and may lead to loss of control,
I_ Know your power tool. Read operator's manual carefully. Learn its applications and
limitations, as well as the specific potential hazards related to this tool. Following this
rule will reduce the risk of electric shock, fire or serious injury_
[] Always wear safety glasses with side shields. Everyday glasses have only impact resistant
lenses. They are NOT safety glasses. Following this rule will reduce the risk of eye injury.
[] Protect your lungs. Wear a face or dust mask if the operation is dusty. Following this rule
wilt reduce the risk of serious personal injury
[] Protect your hearing. Wear hearing protection during extended periods of operation.
Following this rule will reduce the risk of serious person injury.,
[] Battery tools do not have to be plugged into an electrical outlet; therefore, they are
always in operating condition. Be aware of possible hazards when not using your
battery tool or when changing accessories. Following this rule will reduce the risk of electric
shock, fire or serious personal injury.
[] Do not place battery tools or their batteries near fire or heat, This will reduce the risk of
explosion and possibly injury.
[] Do not crush, drop or damage battery pack. Do not use a battery pack or Charger/
Adapter that has been dropped or received a sharp blow. A damaged battery is subject to
explosion. Properly dispose of a dropped or damaged battery immediately_
[] Batteries vent hydrogen gas and can explode in the presence of a source of ignition
such as a pilot light. To reduce the risk of serious personal injury, never use any cordless
product in the presence of open flame. An exploded battery can propel debris and chemicals, if
exposed, flush with water immediately,
[] Do not charge battery
risk of electric shock.
tool in a damp or wet location, Following this rule will reduce the
[] For best results, your battery tool should be charged in a location where the temperature
is more that 32°F (0°C) but less that 104°F (40°C). Do not store outside or in vehicles.
[] Under extreme usage or temperature conditions, battery leakage may occur. If liquid
comes in contact with your skin, wash immediately wit soap and water, then neutralize
with lemon juice or vinegar. If liquid gets in your eyes, flush them with clean water for at
least 10 minutes, then seek immediate medical attention. Following this rule will reduce the
risk of serious personal injury_
[] Save these instructions, Refer to them frequently and use them to instruct others who may
use this toot., if you loan someone this toot, also loan them these instructions.
[] If the power supply cord is damaged, it must be replaced only by the manufacturer or by an
authorized service center to avoid risk.
instructions
below
may
result in electric
fire andlor Failure
serious topersonal
_.WARNIING: listed
READ
AND
UNDERSTAND
ALLshock,
INSTRUCTIONS.
follow allinjury.
I_ Before using battery ChargertAdapter,
read all instructions and cautionary markings in this
manual, on battery Charger/Adapter,
battery and product using battery to prevent misuse of
the products and possible injury or damage,.
_CAUTIION:
To reduce the risk of electric shock or damage to the Charger/Adapter
and
battery, charge only lithium-ion rechargeable batteries as specifically designated on your
ChargertAdapter. Other types of batteries may burst, causing personal injury or damage.
[] Do not use Charger/Adapter
outdoors or expose to wet or damp conditions. Water
entering Charger/Adapter will increase the risk of electric shock_
11 Use of an attachment not recommended or sold by the battery ChargertAdapter
manufacturer
may result in a risk of fire, electric shock or injury to persons. Following
this rule will reduce the risk of electric shock, fire or serious personal injury.
[] Do not abuse cord or Charger/Adapter.
Never use the cord to carry the Charger!Adapter
o Do not pull the Charger/Adapter cord rather than the plug when disconnecting from
receptacle° Damage to the cord or Charger/Adapter could occur and create an electric shock
hazard. Replace damaged cords immediately_
[] Make sure cord is located so that it will not be stepped on, tripped over, come in
contact with sharp edges or moving parts or otherwise subjected to damage or stress.
This will reduce the risk of accidental falls, which could cause injury and damage to the cord,
which could result in electric shock_
[] Keep cord and ChargerlAdapter
parts.
from heat to prevent damage to housing or internal
[] Do not let gasoline, oils, petroleum-based products, etc. come in contact with plastic
parts. They contain chemicals that can damage, weaken or destroy plastic_
[] An extension cord should not be used unless absolutely necessary. Use of improper
extension cord could result in a risk of fire and electric shock. If an extension cord must
be used, make sure:
1. That pins on plug of extension cord are the same number, size and shape as hose of plug on
Charger/Adapter _
2. That extension cord is properly wired and in good electrical condition; and
3. That wire size is large enough for AC ampere rating of Charger/Adapter
Cord Length (Feet)
25'
50'
100'
Cord Size (AWG)
16
16
16
as specified below:
NOTE: AWG = American Wire Gauge
[] Do not operate ChargerlAdapter
with a damaged cord or plug, which could cause
shorting and electric shock. If damaged, have the Charger/Adapter repaired or replaced by an
authorized service technician at Sears Service Center,
[] Do not operate Charger/Adapter
if it has received a sharp blow, been dropped or
otherwise damaged in any way. Take it to an authorized service technician at Sears Service
Center for an electrical check to determine if the Charger/Adapter is in good working order
[] Do not disassemble ChargerlAdapter.
Take it to an authorized service technician at Sears
Service Center when service or repair is required. Incorrect reassembly may result in a risk of
electric shock or fire_
[] Unplug Charger/Adapter
from outlet before attempting
reduce the risk of electric shock,
8
any maintenance
or cleaning to
[]
Disconnect Charger/Adapter
from the power supply when not in use. This wilt reduce
the risk of electric shock or damage to the Charger/Adapter if metal items should fall into the
opening It will also help prevent damage to the Charger/Adapter during a power surge°
[] Risk of electric
battery terminal
shock.
Do not touch uninsulated portion of output connector or uninsulated
[] Save these instructions,
Refer to them frequently and use them to instruct others who may
use this toot,, If you loan someone this tool, loan them these instructions also to prevent misuse
of the product and possible injury.
[] SAVE THESE INSTRUCTIONS° This manual contains important safety and operating
instructions for battery Charger/Adapter 320.25709 and battery pack 320°25708,
[] Before using battery Charger/Adapter,
read all instructions and cautionary markings on
battery Charger/Adapter,
battery and product using battery.
[] CAUTION. To reduce the risk of injury, charge only lithium-ion rechargeable
types of batteries may burst, causing personal injury or damage,
batteries. Other
,_WARNIING:
Use of this product can generate dust containing chemicals known to
the state of California to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
[] Lead from lead-based paints_
[] Crystalline silica from bricks and cement and other masonry products_
[] Arsenic and chromium, from chemically treated lumber,
Your risk from these exposures varies, depending upon how often you do this type of
work. To reduce your exposure to these chemicals:
[] Work in a well-ventilated area.,
[] Work with approved safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles,
Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling and
other construction activities. Wear protective clothing and wash exposed areas with soap
and water, Allowing dust to get into your mouth, eyes or lay on the skin may promote absorption
of harmful chemicals,
F_g. 1
Two-Speed
Gear Box
Torque
Adjustment
Ring
Vents
Direction
of Rotation
Selector
(FORWARD/CENTER
LOCK/REVERSE)
/
Ratcheting
Keyless
Chuck
Trigger
Switch
Integrated
LED Worklight
Chuck
3/8-in. Soft Grip Chuck
Motor
16 Volt DC
Switch
VSR (Variable Speed Reversible)
No Load Speed
LO 0-280 / HI 0-1,200 (RPM)
Clutch
24 Position
Torque
320 inoIbs..
Drill/Driver Weight (without battery)
2,66 Ibs.
Battery Type
Lithium-ton
Battery Voltage
16.0 Volt DC
.....
Charger/Adapter.
........Input
120-Volts, 60 Hz AC only
Optimum Charging Temperature
32°F (0° C) -104°F (40°C)
10
KNOW YOUR DRILL/DRIVER
(Fig. 1)
,_k',tVARNIING; The safe use of this product requires an understanding of the information on
the tool and in this operator's manual as well as a knowledge of the project you are attempting.
Before use of this product, familiarize yourself with all operating features and safety rules_
ADJUSTABLE TORQUE
The drill has a 24-position clutch_ The torque adjustment clutch can be turned to select the right
amount of torque for your application.
TWO-SPEED
GEAR BOX
The two-speed gear box is designed for drilling or driving at LO or HI speeds. A slide switch is
Eocated on top of your drill for selecting the appropriate speed,
VARIABLE SPEED
The variable speed trigger switch delivers higher speed with increased trigger pressure and lower
speed with decreased trigger pressure.
RATCHETING KEYLESS CHUCK
The keyless chuck allows you to hand-tighten or release the drill bit in the chuck jaws, The
ratcheting feature is designed to prevent the chuck from opening during operation..
FORWARD/REVERSEICENTER
LOCK
The drill has a direction of rotation selector located above the trigger switch for changing the
direction of bit rotation. Setting the trigger switch in the OFF (center lock) position helps reduce
the possibility of accidental starting when not in use.
LED WORKLIGHT
The LED worklight, located on the front of the drill base, illuminates when the trigger switch is
depressed° This feature provides extra light for increased visibility.
,_INARNPNG:
If any parts are broken or missing, DO NOT attempt to plug in the power
cord or operate drill until the broken or missing parts are replaced. Failure to do so
could result in possible serious injury.
,_WARNIING:
Do not attempt to modify this drill or create accessories not
recommended for use with this drill. Any such alteration or modification is misuse and
could result in a hazardous condition leading to possible serious injury.
_WARNI]NG:
To prevent accidental starting that could cause serious personal injury,
always remove the battery pack from the drill when assembling parts.
UNPACKING
This product has been shipped completely assembled.
[] Carefully remove the tool and any accessories from the box, Make sure that all items listed in
the packing list are included.
[] Inspect the too! carefully to make sure no breakage or damage occurred during shipping.
[] Do not discard the packing material until you have carefully inspected and satisfactoriry
operated the drill
[] If any parts are damaged or missing, please refer to the numbers listed on the back page of
operator's manua!_
PACKING LIST
Drill/Driver,
Double-ended
Bit, Operator's
Manual
11
POWER BAR
B This Lithium-Ion battery pack is equipped with a POWER BAR which is used to display the
battery pack's remaining run time, Press the POWER BAR button to display the LED lights.. The
LED lights will stay lit for approximately 4 seconds.
NOTE: The POWER BAR can be used when the battery is attached or removed from tool. 1
Fig, 2
@@@@
80-100%
Charge
0®®®
60-79%
Charge
00@®
40-59%
Charge
000@
20-39%
Charge
0
Under 10%
Charge
1
If
I
il
Completely
discharged
LOW CAPACITY WARNING
[] If one LED on the POWER BAR begins to flash, the battery pack's charge is under 10%
capacity and should be recharged.
t_t Unlike other battery pack types, Lithium-lon battery packs deliver fade-free power for their
entire run time. The tool will not experience a slow, gradual loss of power as you work, To
signal that the battery pack is at the end of its run time and needs to be charged, power to the
tool will drop quickly,. The POWER BAR will begin to display four flashing LED lights when it is
completely discharged_ When this happens, remove the tool from the workpiece and charge
the battery pack as needed.
NOTE:
or
high The
temperature
POWER BAR
situation
may also
(see display
SmartChip
fourTMflashing
Battery LED
protection),
lights due to an overload
SmartChip
TM
BATTERY PROTECTION
SmartChip TM intuitive circuitry protects the battery pack from extreme temperature, over-discharge
and over-charge,.To protect the battery from damage and prolong its life, the battery pack's
SmartChip TM circuitry witl turn off the battery pack if it becomes overloaded or if the temperature
becomes too high during use. This may happen in extremely high torque, binding and stalling
situations. This intelligent system will shutdown your battery pack if its operating temperature
exceeds 176°F (80°C) and witl begin normal operation when it returns to 32°F (0°C) - 122°F (50°C).
[] The POWER BAR will display four flashing LED lights if the SmartChip TM circuitry detects a
momentary overloado You can conveniently reset the battery pack by pressing the POWER
BAR button.. Press the POWER BAR button again to display the remaining charge..
[
I
NOTE: If the POWER BAR continues to flash four LED lights after reset, place the
battery pack on the ChargerlAdapter
to evaluate the battery condition (see Fig. 4).
12
l
i
NOTE: A significantly reduced run time after fully charging the battery pack indicates
that the batteries are near the end of their usable life and must be replaced.
J
I
COLD WEATHER OPERATION
[] This Lithium-Ion battery pack will provide optimal performance in temperatures between 32°F
(0°C) and 104°F (40°C).. When the battery pack is very cold, it may "pulse" for the first minute
of use to warm itself up. Put the battery pack on a tool and use the tool in a light application,
After about a minute, the battery pack will have warmed itself up and will operate normally.
WHEN TO CHARGE THE BATTERY PACK
The Lithium-!on battery can be charged at any time and will not develop a "memory" when
charged after only a partial discharge. It is not necessary to run down the battery pack charge
before recharging. Remove the battery pack from the tool when convenient for you and your job.
[] Use the POWER BAR to determine when you need to recharge the battery pack.
[] You can "top-off" your battery pack's charge before starting a big job or long period of use°
[] Due to Lithium-Ion's fade-free properties, the only time it is necessary to charge the LithiumIon battery pack is when the pack has reached the end of its charge. To signal the end of
charge, power to the tool will drop quickly, Charge the battery pack as needed.
HOW TO CHARGE THE BATTERY PACK
NOTE: This Lithium-Ion battery pack is shipped partially charged. Before using it the
first time, fully charge the battery pack.
J
I
A fully discharged batter'/pack with a temperature between 32°F (0°C) and 104°F (40°C) will charge
[] Charge the Lithium-Ion battery pack only
with the correct Charger/Adapter.
Fig. 3
[] Connect the Charger/Adapter to a power supply.
I_ Attach the battery pack to the Charger/
Adapter by aligning the raised ribs of the
battery pack with the slot in the Charger/
Adapter. Slide the battery pack onto the
Charger/Adapter
(Fig. 3)
[] The Charger!Adapter will communicate with
the battery pack's SmartChip TM circuitry to
evaluate the condition of the battery pack.
[] The POWER BAR LED lights will cycle from
right to left during charging° This is part of the
normal charging operation
[] After charging is complete, the green LED
on the Charger/Adapter will come on and
the POWER BAR LED lights will go off. The
POWER BAR LED lights will not be displayed
when the POWER BAR button is pressed while
the battery pack is on the Charger/Adapter,
i_ The battery pack will fully charge, but will not
overcharge, if left on the Charger/Adapter.
NOTE: For your convenience, the Charger/Adapter
and inverters rated at 300 watts or higher.
13
can operate with most generators
1
LED FUNCTIONS
OF ChargerlAdapter
(Fig. 4)
Fig. 4
LED INDICATOR
_)
(SEE
I/LO MANUAL)
TEMP,,
[_
BATTERY
PACK
RED
LED
GREEN
LED
ACTION
HotlCold
battery
On
Off
Charging will begin when
battery returns to
32OF (0°C)_104°F (40°C)
,,,....
BATTERY
DEFECTIVE
CHARGING
BATTERY
FULL
BATTERY
CHARGING
[_
-
,
,, ,,,,,, ,,
Defective
Flashing
Off
Battery pack or Charger/
Adapter is defective
Charging
Off
Flashing
Charging
Fully
charged
Off
On
Charging is complete
Maintenance charging
A HOT BATTERY PACK
If the battery pack is above normal temperature range, the red LED will be lit and the green
LED will be off° When the battery pack cools down to approximately 104°F (40°C), the Charger/
Adapter will automatically begin charging.
CHARGING
A COLD BATTERY PACK
If the battery pack is below the normal temperature range, the red LED will be lit and the green
LED will be off° When the battery warms to a temperature of more than 32°F (0°C), the Charger/
Adapter will automatically begin charging.
DEFECTIVE BATTERY
If the Charger/Adapter
be off°
detects a problem, the red LED will begin flashing and the green LED wil!
Im If defective, remove and reinsert the battery pack in the Charger/Adapter.
reads "defective" a second time, try charging a different battery pack.
if the LED status
[] If a different battery pack charges normally, dispose of the defective battery pack (see
Maintenance section).
[] If a different battery pack also indicates "defective," the Charger/Adapter
may be defective°
BATTERY CHARGING
If the battery pack is within normal temperature range, the green LED will begin flashing and the
red LED will be off., The battery pack wilt reach a full charge in about 60-120 minutes(depends
on battery's capacity). The POWER BAR LED lights will cycle right to left during charging. This
is part of the normal charging operation. The POWER BAR LED lights will not be displayed when
the POWER BAR button is pressed while the battery pack is on the Charger/Adapter.
BATTERY FULL
If the battery pack is within normal temperature range, the green LED will be lit and the red LED will
be off. The battery pack is fully charged and ready to use. The battery pack will fully charge, but will
not overcharge, if left on the Charger/Adapter. The POWER BAR LED lights will not be displayed
when the POWER BAR button is pressed while the battery pack is on the Charger/Adapter.
I
NOTE:
part
of the
Charger/Adapter
normal operation
mayofwarm
the Charger/Adapter.
up with several continuous
Charge in charge
a well ventilated
cycles, This
area°
is
14
I
1
_CAUTBON;
When placing the battery pack in the tool, be sure the raised rib on the
battery pack aligns with the bottom of the drill and latches into place properly. Improper
installation of the battery pack can cause damage to internal components.
_WARNIING:
Do not attempt to modify this drill or create accessories not
recommended for use with this drill. Any such alteration or modification is misuse
and could result in a hazardous condition leading to possible serious injury,
TO ATTACH BATTERY PACK (Fig 6)
[] Lock the trigger switch on the drill by placing
the direction of rotation (forward/reverse/
center lock) selector in center position
Fig. 6
Align the raised portion on the battery pack
with the grooves on the bottom of the drill,
then attach the battery pack to the drill as
shown
i_t Make sure the latch on the battery pack
snaps into place and the battery pack
is secured to the drill before beginning
operation,
TO DETACH BATTERY PACK (Fig. 6)
[] Lock the trigger switch on the drilt by placing the direction of rotation (forward/reverse/center
lock) selector in center position
[] Press the latch located on the front of the battery pack to release battery pack°
I_ Pull forward on the battery pack to remove from the drill
A_kWARHJNG:
are be
always
operating
condition.
Therefore,
direction
rotation selectorBattery
shouldtools
always
lockedin when
not in
use or carrying
at your
side. of
15
TRIGGER SWITCH (Fig. 7)
Fig, 7
To turn the drill ON, depress the switch trigger,
To turn it OFF, release the trigger.
VARIABLE
Direction
of rotation
selector
SPEED (Fig, 7)
The variable speed trigger switch delivers
higher speed with increased trigger pressure
and lower speed with decreased trigger
pressure.
DIRECTION OF ROTATION SELECTOR
(FORWARD!REVERSE!CENTER
LOCK) (Fig. 7)
The direction of bit rotation is reversible and
is controlled by a selector located above the
trigger switch,
Variable
speed
trigger
switch
With the drill held in normal operating position:
[] Position the direction of rotation selector to
the left of the tool for drilling.
[] Position the direction of rotation selector to
the right of the tool for reverse°
[] Setting the switch in the OFF (center lock)
position helps reduce the possibility of
accidental starting when net in use,
I
_CAUTBOit, a: To prevent gear damage, always allow the chuck to come to complete
stop before changing the direction of rotation,
J
!
NOTE:
drill will not run unless the direction of rotation selector is engaged fully to ]
the
left The
or right.
ELECTRIC
BRAKE
To stop the drill, release the trigger switch and allow the chuck to come to a complete stop. The
electric brake quickly stops the chuck from rotating. This feature engages automatically when you
release the trigger switch,,
RATCHETING
KEYLESS CHUCK (Fig 8)
Fig, 8
Ratcheting
keyless
The drill has a ratcheting keyless chuck to
tighten or release drill bits in the chuck jaws.
The arrows on the chuck indicate which
direction to rotate the chuck body in order to
GRIP (tighten) or OPEN (release) the chuck
jaws on the drill bit. The ratcheting feature is
designed to prevent the chuck from opening
during operation,
Chuck
OPEN
release)
chuck
jaws
Chuck
,_kWARNIING: Do not hold the chuck
body with one hand and use the power
of the drill to tighten the chuck jaws on
the drill bit. The chuck body could slip
in your hand, or your hand could slip
and come in contact with the rotating
bit° This could cause an accident
resulting in serious personal injury.
GRIP
(tighten)
16
1
TWO-SPEED
GEAR BOX (Fig, 9)
Fig. 9
Two-speed
gear box
switch
The drill has a two-speed gear box designed
for drilling or driving at LO or HI speeds. A
slide switch is located on the top of the drill to
select either LO or HI speed. When using drill
in the LO speed range, speed will decrease
and the drill will have more power and torque°
When using drill in the HI speed range, speed
will increase and the drill will have less power
and torque, Use LO speed for high power and
torque applications and HI speed for fast drilling
or driving application&
HI
LO
NOTE: Avoid running the drill at LO
speed for extended periods of time,
Running at LO speed under constant
usage may cause the drill to become
overheated. If this occurs, cool the drill
by running it without a load at HI speed.
I
,_CAUTION:
while
could
result in Never
seriouschange
damagegears
to the
drill.the tool is running, Failure to obey this caution 1
ADJUSTABLE
TORQUE CLUTCH (Fig 10)
When using the drill/driver for different driving applications, it is necessary to increase or
decrease the torque in order to help prevent the possibility of damaging screw heads, threads,
workpiece, etc,. In general, torque intensity should correspond to the screw diameter., If the torque
is too high or the screws too small, the screws may be damaged or broken.
The torque is adjusted by rotating the torque
adjustment ring.
Fig.
The torque is greater when the torque
adjustment ring is set on a higher setting. The
torque is less when the torque adjustment is set
on a lower setting.
To decrease ]
Torque
ring
The proper setting depends on the type of
material and the size of screw you are using.
Select the option that best matches the type of
bit, fastener and material you will be using°
[] Choose the correct speed: LO or HI.
To increase
torque
[] Choose the correct torque setting
DRILL MODE (Fig, 11)
Fig. 1t
Select drill mode for drilling and other heavy
duty applications,
[] To select drill mode, rotate the torque
adjustment ring until the _.&'_icon aligns with
the torque indicator and dicks into position.,
17
Drill icon
Torque indicator
LED WORKL1GHT (Fig. 12)
Fig. 12
The LED worklight located on the base of the
drill will come on when the trigger switch is
depressed, The LED worklight will turn off when
the trigger switch is released° This provides
additional lighting on the surface of the
workpiece for operation in lower-light areas.
BIT STORAGE (Fig. 13)
When not is use, the bit provided with the
drill can be stored on the base of the drill by
snapping it into place in the bit clip.
Fig. 13
INSTALLING
LED
worklight
Bit clip
Ratcheting
keyless
chuck
BITS (Fig. 14)
[] Lock the trigger switch by placing the
direction of rotation selector in the OFF
(center) position,
Drill bit
[] Open or close the chuck jaws to a point
where the opening is slightly larger than the
bit size you intend to use., Also, raise the front
of the drill slightly to keep the bit from falling
out of the chuck jaws.
OPEN
(release)
Chuck
jaws
Chuck
body
I_ Insert a drill bit.
NOTE: Rotate the chuck body in the
direction of the arrow marked GRIP to
close the chuck jaws° Do not use a wrench
to tighten or loosen the chuck jaws,
[] Tighten the chuck jaws securely on the bit,,
REMOVING BITS (Fig,, 14)
F_g. 15
[] Lock the trigger switch by placing the
direction of rotation selector in the OFF
(center) position.
WRONG!
[] Open the chuck jaws,,
NOTE: Rotate the chuck body in the
direction of the arrow marked OPEN to
open the chuck jaws. Do not use a wrench
to tighten or loosen the chuck jaws.
WRONG!
[] Remove the drill bit°
_kWARN_HG:
Make sure to insert the drill bit straight into the chuck jaws. Do not
insert the drill bit into the chuck jaws at an angle then tighten, as shown in figure 15,
This could cause the drill bit to be thrown from the drill, resulting in possible serious
personal injury or damage to the chuck,
18
STRAIGHT DRILLING (Fig 16)
Fig. t6
[] The dirtl has a bubble vial that can indicate
straight when you wanted straight drill, by
doing this, just need to make sure the bubble
is in the center of the vial..
Bubble vial
.........
-'1
DRILLING (Fig 17)
[] Check the direction of rotation selector for
the correct setting (forward or reverse).
[] Secure the material to be drilled in a vise or
with clamps to keep it from turning as the drill
bit rotates_
[] Hold the drill firmly and place the bit at the
point to be drilled.,
[] Depress the trigger switch to start the drill°
[] Move the drill bit into the workpiece, applying
only enough pressure to keep the bit cutting,
Do not force the drill or apply side pressure to
elongate a hole. Let the toot do the work.
[] When drilling hard, smooth surfaces, use
a center punch to mark the desired hole
Iocation_ This wil! prevent the drill bit from
slipping off-center as the hole is started
1_tWhen drilling metals, use a light oil on the
drill bit to keep it from overheating° The oil
will prolong the life of the bit and increase the
drilling action.
S !f the bit jams in the workpiece or if the drill
stalls, stop the tool immediately_ Remove the
bit from the workpiece and determine the
reason for jamming.
NOTE: This drill is equipped with
an electric brake. When the brake is
functioning properly, sparks may be visible
through the vent slots in the housing. This
is normal and is the action of the brake.
A_kWARINIIING: Be prepared for binding at bit breakthrough.
When these situations
1
occur, the drill has a tendency to grab and kick opposite to the direction of rotation and I
could cause loss of control when breaking through material. If not prepared, this loss of I
control can result in possible serious injury.
I
19
WOODDRILLING
Formaximumperformance,
usehighspeedsteelor bradpointbitsforwooddrilling
[] Begindrillingata verylowspeedtopreventthebitfromslippingoffthe startingpoint..Increase
speedas thedrill bitbitesintothematerial°
[] Whendrilling"through"holes,placea blockofwoodbehindtheworkpieceto preventragged
or splinterededgesonthe backsideoftheholeo
METAL DRILLING
For maximum performance, use high speed steel bits for metal or steel drilling,.
[] When drilling metals, use a light oil on the drill bit to keep it from overheating. The oil will
prolong the life of the bit and increase the drilling action°
[] Begin drilling at a very low speed to prevent the bit from slipping off the starting point.
[] Maintain a speed and pressure which allows cutting without overheating the bit. Applying too
much pressure will:
- Overheat the drill
- Wear the bearings.
- Bend or burn bits..
- Produce off-center or irregular-shaped
MASONRY
holes.
DRILLING
For maximum performance, use carbide-tipped
concrete, etc.
masonry bits when drilling holes in brick, tile,
lm Maintain a speed and pressure which allows cutting without overheating the bit or drill
Applying too much pressure will:
- Overheat the drili_
- Wear the bearings.
- Bend or burn bits..
- Produce off-center or irregular-shaped holes,
[] Apply light pressure and medium speed for best results in brick.
[] Apply additional pressure for hard materials such as concrete.
[] When drilling holes in tile, practice on a scrap piece to determine the best speed and pressure°
Begin drilling at a very low speed to prevent the bit from slipping off the starting point,
i
_kWARNONG-"
Alwaysorwear
goggles
safety glasses
withalso
sidewear
shields
during
power tool operation
whensafety
blowing
dust. or
If operation
is dusty,
a dust
mask.]]
[
,_kWARNII_IG=
ensure safety
and Service
reliability,Center.
all repairs should be performed by a
qualified
serviceTotechnician
at Sears
2O
!
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from
various types of commercial solvents and may be damaged by their use. Use clean cloths to
remove dirt, dust, oil, grease, etc,
_WARHIING:
Do not at any time let brake fluids, gasoline, petroleum-based products,
penetrating oils, etc., come in contact with plastic parts. Chemicals can damage,
weaken or destroy plastic which may result in serious personal injury.
[
_,WARNINGI
serious personal
always
remove the any
battery
pack from th t
tool
and unplug To
theavoid
Charger/Adapter
wheninjury,
cleaning
or performing
maintenance.
BATTERIES
The battery pack is equipped with Lithium-Ion rechargeable
each charge will depend on the type of work performed.
batteries. The duration of use from
The batteries in this tool have been designed to provide maximum trouble-free life. Like all
batteries, they will eventually wear out. Do not disassemble the battery pack or attempt to replace
the batteries.. Handling of the batteries, especially when wearing rings and jewelry, could result in
a serious burn.
To obtain the longest possible battery life, read and understand the operators manual.
[] It is good practice to unplug the Charger/Adapter
when not in use°
and remove the Lithium-Ion battery pack
For Lithium-ion battery pack storage longer than 30 days:
[] Store the Lithium-Ion battery pack where the temperature
moisture,
is below 80°F (26°C) and free of
[] Store Lithium-Ion battery packs in a 30%-50% charged condition,
[] Every six months of storage, fully charge the Lithium-Ion battery pack,
[] Exterior may be cleaned with a cloth or soft non-metallic
BATTERY PACK REMOVAL AND PREPARATION
brush,
FOR RECYCLING
To preserve natural resources, please recycle or dispose of batteries properly.
This product contains lithium-ion batteries_ Local, state or federal laws may
prohibit disposal of lithium-ion batteries in ordinary trash Consult your local
waste authority for information regarding available recycling and/or disposal
options_
_WARINIItNG:
Upon removal, cover the battery pack's terminals with heavy-duty
adhesive tape. Do not attempt to destroy or disassemble the battery pack or remove
any of its components. Lithium-Ion batteries must be recycled or disposed of properly.
Also, never touch the terminals with metal objects andlor body parts as a short circuit
may result. Keep away from children. Failure to comply with these warnings could
result in fire and/or serious injury.
21
CHUCKREMOVAL
(Fig,18-20)
Thechuckcanberemovedandreplacebya
newone.
E Lockthetriggerswitchbyplacingthe
directionofrotationselectorincenterposition,
[] Openthechuckjaws,.
M Inserta 5/16-in,or largerhexkeyintothe
chuckofthedrillandtightenthechuckjaws
securely.
[] Tapthehexkeysharpfywitha malletin
a clockwisedirection.Thiswillloosenthe
screwinthe chuckforeasyremoval,
[] Openthechuckjawsandremovethehex
key°Usinga screwdriver,
removethechuck
screwbyturningit in a clockwisedirection,.
Ratcheting
keyless
chuck
Fig. 18
Mallet
Chuck
Jaws
Hex key
1
threads.
NOTE:The chuck screw has left handed
|
J
Screwdriver
[] Insert the hex key into the chuck and tighten
the chuck jaws securely. Tap sharply with a
mallet in a counterclockwise direction., This
will loosen the chuck on the spindle. It can
now be unscrewed by hand.,
TO RETIGHTEN A LOOSE CHUCK
The
and
may
bind
chuck may become loose on the spindle
develop a wobbler Also, the chuck screw
become loose, causing the chuck jaws to
and prevent them from closing,,
Mallet
Ratcheting
keyless
chuck
To tighten a loose chuck or chuck screw:
El Lock the trigger switch by placing the
direction of rotation selector in center position.
[] Open the chuck jaws,
[] Insert the hex key into the chuck and tighten
the chuck jaws securely,, Tap the hex key
sharply with a mallet in a clockwise direction.
This will tighten the chuck on the spindle,
Hex key
[] Open the chuck jaws and remove the hex key.
[] Using a screwdriver, tighten the chuck
screw by turning the chuck Screw in a
counterclockwise direction_
Chuck
Jaws
_WARNgNG:
Always wear safety glasses with side shields during maintenance.
_WARI_J_NG:
To ensure safety and reliability, all repairs
qualified service technician at Sears Service Center.
22
should be performed by a
l
l
16.0 VOLT LITHIUM-ION CORDLESS
3/8-in. DRILL I DRIVER
MODEL NUMBER 320.10320
16.0 VOLT LITHIUM-ION CORDLESS 3/8-in. DRILL/DRIVER
MODEL NUMBER 320.10320
The Model Number will be found on the Nameplate attached to the right side of the drill. Always
mention the Model Number in all correspondence regarding your tool.
IIT_M NO.
PARTS
MO,
PART DESCRIIPTION
QTY.
-L
1
3810357000
Screw Bit
2
3402175000
Contact Receptacle ASSY
1
1
....
L,
3
3121435000
Plastic Sleeve
1
4
3700963000
Lantern Ring
1
5
5650007000
Spring Washer
2
6
5700046000
Steel Ball
6
...........................
,.,_ .......
i, L L ,,
7
5610002000
Tapping Screw
5
8
5610013000
Tapping Screw
10
10
2242896000
Name Plate
1
3703983000
Spring Stop
I
11
,
,
,,,,,,,,,,,,,,,,,_,,
12
3703673000
Bits Holder
1
13
3550289000
Torque Pin
6
14
3704024000
Mounting Plate
1
15
3123511000
Clutch Cap
1
16
5620179000
Screw (LH_)
1
3700408000
Gasket I
1
17
.......
,,,,, ,,
, ,,,,,
18
4920155000
Shrinkable Tube
7
19
3703909000
Heat Sink
1
2O
4870346000
Trigger Switch
1
21
2790119000
Gear Case ASSY
1
22
3860086000
Chuck
1
23
3320520000
Left Housing Assy
1
24
3123552000
Decorate Cover
1
, ,,
,,,,,,,,,, ,,,,
_,
25
3320521000
Right Housing Assy
1
26
3700960000
Handle Hoop
1
27
3123528OOO
1
Right Decorate cover
,,,
,
,,, ,,,,,
28
366O109000
Spring
1
29
2810126000
Vial
1
3O
3123494000
Spring Holder
1
31
342060000O
Decorate Cover
L '"'
31228170O0
Speed
24
Change Button
,,, ,,,,,,,,,,,,
'
1
,,,,L
32
,,,
1
,
,,,
'"' '""
16.0 VOLT LtTHIUIVI-ION CORDLESS 3/8-in. DRILL/DRIVER
MODEL NUMBER 320.10320
The Model Number wil! be found on the Nameplate attached to the right side of the drill. Always
mention the Model Number in all correspondence regarding your tool
ITEM NO.
PARTS
33
HO.
PART DESCRIPTIOINI
3123529000
Left Decorate Cover
.............
" *,
34
3123133000
35
3700961000
QTY.
: ...................
,, ,,,,,,, ,, ,,
1
L..............
F/R Button
1
Stop Spring
1
Switch Trigger
1
,,,, ,,,,,,,
36
3320525000
--
, , ,
L
........
37
5620037000
Screw
2
38
5620031000
Screw
1
39
5650003000
Spring Washer
1
40
2822395000
DO Motor ASSY
1
LED
1
Lead Resistor
1
,_, ,,,,, ,,,,L
41
4360225000
,,,,,, ,
42
,
,
,
......................
4120311000
SEE BACK PAGE FOR PARTS
ORDERIIIRG
25
ttHSTRUCTIONS
26
27
r.
Get it fixed, at your home or ourS!
Your Home
For repair-in
your home-of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement
parts, accessories
and
owner's manuals that you need to do-it-yourself,
For Sears professional
installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
®
(1-800-469-4663)
www.sears.com
Anytime, day or night
(U S A. and Canada)
www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronic, call or go omline for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Anytime, day or night (USoA. only)
www.sears,com
To purchase
or maintenance
a protection
agreement
1-800-827-6655
agreement
(Canada) on a product serviced
(US.A.)
1-800-361-6665
Para pedir servicio de reparaci6n
a domicilio, y para ordenar piezas:
1-888-SU-HOGAR
(U.S.A.)
e
(1-888-784-6427)
by Sears:
(Canada)
Au Canada pour service en franqais:
1-800-LE-FOYER
Mc
(1-800-533-6937)
www.sears,,ca
Se lr
©Sears Brands, LLC
® Registered Trademark / TMTrademark / SMService Mark of Sears Brands, LLC
® Marca Registrada / TMMarca de Fabrica / SMMarca de Servicio de Sears Brands, LLC
MCMarque de commerce / MDMarque d_pos_e de Sears Brands, LLC