Care, Use and Installation booklet

1950756200 English (US), French (Canadian), Spanish (US) {PDF Created 12/05/09 09:56:00}
Care, Use and Installation booklet
TUMBLE DRYER
EN
F
English, 1
Français, 13
Contents
ES
Warnings and Safety instructions, 3
Important safety instructions
Grounding Instructions
Espanol, 25
Dryer Description, 4
The front
The back
Control panel
Start and Programs, 5-6
Choosing a Program
Table of Programs
Laundry, 6-7
Sorting your laundry
Wash care labels
Special clothing items
Drying times
Maintenance and Care, 9
When to Switch off the
electricity
Clean the filter after
each cycle
Check the drum after
each cycle
Cleaning the dryer
Troubleshooting, 10
Spare Parts
Installation, 11-12
TVM63
Electrical
Where to put your dryer
Exhaust Ducting
Stacking Kit
Warranties, 13
3
1950756200 English (US), French (Canadian), Spanish (US) {PDF Created 12/05/09 09:56:00}
2
1950756200 English (US), French (Canadian), Spanish (US) {PDF Created 12/05/09 09:56:00}
TD4176 Issue 1
WARNING Risk of Fir
–
e
Clothes dryer installation must be performed by a qualified installer.
Install the clothes dryer according to the manufacturer’s instructions and local codes.
Do not install a clothes dryer with flexible plastic venting materials.
If flexible metal (foil type) duct is installed, it must be of a specific type
identified by the appliance manufacturer as suitable for use with clothes dryers.
Flexible venting materials are known to collapse, be easily crushed, and trap lint.
These conditions will obstruct clothes dryer airflow and increase the risk of fire.
To reduce the risk of severe injury or death, follow all installation instructions.
Save these instructions.
«
AVERTISSEMENT. Risque d’incendie.»
«Les sécheuses doivent être installé espar un installateur qualifié.»
«Les sécheuses doivent être installées selon les instructions du fabricant et les codes locaux.»
«Ne pas raccorder de matériaux d’évacuation en plastique à une sécheuse. Si une gaine métallique flexible (de
type pellicule métallique) est installée, elle doit être d’un type recommandé par le fabricant pour utilisation avec la
sécheuse. Les matériaux d’évacuation en plastique ont tendance à s’affaisser, et ils sont faciles à écraser et
retiennent la charpie. Ces conditions obstrueront la circulation de l’air et augmenteront le risque d’incendie.»
«Afin de réduire le risque de blessure grave ou de mort, suivre toutes les instructions d’installation.»
«Conserver ces instructions.»
Advertencia -
Riesg o d e Incen di o
La instalación de la secadora de ropa debe ser realizada por un instalador calificado.
Instale la secadora de ropa de acuerdo con las instrucciones del fabricante y los códigos locales.
No instale la secadora de ropa con materiales de ventilación de plástico flexibles.
Si instala un conducto de metal flexible (tipo lámina), éste debe ser del tipo específico identificado por el
fabricante del electrodoméstico como adecuado para su utilización en secadoras de ropa.
Se conoce que los materiales de ventilación de plástico colapsan, se aplastan fácilmente y atrapan pelusas.
Estas condiciones obstruirán la salida se aire y aumentarán el riesgo de incendio.
Para reducir el riesgo de daño severo o muerte, siga todas las instrucciones de instalación.
Guarde estas instrucciones.
1
1950756200 English (US), French (Canadian), Spanish (US) {PDF Created 12/05/09 09:56:00}
Warnings and Safety Instructions
TD4079C15 Issue 1
! This appliance has been designed and built according
to international safety standards. These warnings are
given for safety reasons and must be read carefully.
Important Safety Instructions
•
•
•
•
•
•
•
•
•
•
•
WARNING
To reduce the risk of fire, electric shock or injury
to persons when using your appliance, follow
the basic precautions including the following.
Read all the instructions before using the appliance.
Do not dry articles that have been previously cleaned
in, washed in, soaked in, or spotted with gasoline, drycleaning solvents, or other flammable or explosive
substances, as they give off vapors that could ignite or
explode
Do not allow children to play on or in the appliance.
Close supervision of children is necessary when the
appliance is used near children.
Before the appliance is removed from service or
discarded, remove the door to the drying
compartment.
Do not reach into the appliance if the drum is moving.
Do not install or store this appliance where it will be
exposed to the weather.
Do not tamper with the controls.
Do not repair or replace any part of the appliance or
attempt any servicing unless specifically
recommended in the user-maintenance instructions.
Do not use fabric softeners or products to eliminate
static unless recommended by the manufacturer of
the fabric softener or product.
Do not use heat to dry articles containing foam rubber
or similarly textured rubber-like materials.
Clean lint filter before and after each load. (see
Maintenance
• Keep area around the exhaust opening and adjacent
surroundings free from the accumulation of lint, dust,
and dirt.
• The interior of the appliance and exhaust duct should
be cleaned periodically by qualified service personnel.
• Do not place items exposed to cooking oils in your
dryer. Items contaminated with cooking oils may
contribute to a chemical reaction that could cause a
load to catch fire.
• This tumble dryer has been designed for home, and not
professional, use.
• This dryer must be used by adults, and the instructions
in this booklet should be followed carefully.
• Do not touch the appliance while barefoot or with wet
hands or feet.
• The appliance must be installed correctly and have
proper ventilation. The air intake vents behind the
machine, the outlet vents. should never be obstructed.
(see Installation).
• Check to see if the dryer is empty before loading it.
The back of the dryer could become very
hot. Never touch it while in use.
•
• Do not use the dryer unless the filter is securely in place
(see Maintenance)
• Do not overload the dryer (see Laundry for maximum
loads).
• Do not load items that are dripping wet.
• Tumble dry items only if they have been washed with
detergent and water, rinsed, and been through the
spin cycle. It is a fire hazard to dry items that HAVE
NOT been washed with water.
• Carefully check all instructions on clothing labels (see
Laundry).
• Do not tumble dry large, very bulky items.
• Do not tumble dry acrylic fibers at high
temperatures.
• Complete each program with its Air Fluff
phase.
• Do not turn off the dryer when there are still warm
items inside.
• Never climb on top of the dryer. It could result in
damage.
• Comply with specified electrical requirements. (see
Installation).
• Always buy original spare parts and accessories
(see Troubleshooting).
EN
Grounding Instructions (see Installation).
WARNING:
THIS APPLIANCE MUST BE GROUNDED.
Improper connection of the equipment-grounding conductor can
result in a risk of electric shock. Check with a qualified
electrician or service representative or personnel if you are in
doubt as to whether the appliance is properly grounded. !
In the event of malfunction or breakdown, grounding will
reduce the risk of electric shock by providing a path of
least resistance for electric current. This appliance is
equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
DO NOT modify the plug provided with the appliance: if
it will not fit the outlet, have a proper outlet installed by a
qualified electrician or exchange the cord with an
appropriate one rated for the dryer.
REFER TO THE RATING PLATE FOR VOLTAGE
AND CURRENT REQUIREMENTS. (See diagram for
location)
The dryer should be connected to the mains supply via
a suitable socket which is accessible after installing
your dryer
This dryer must be connected to 15A INDIVIDUAL
BRANCH CIRCUIT.
For full details see Installation Instructions sections of
this book.
IF IN DOUBT ABOUT ANY OF THE ABOVE
CONSULT A QUALIFIED ELECTRICIAN
SAVE THESE INSTRUCTION
4
1950756200 English (US), French (Canadian), Spanish (US) {PDF Created 12/05/09 09:56:00}
Dryer Description
TD4177W Issue 1
The front
The back
EN
Control Panel
The START button begins drying a selected
program (see Start and Programs).
The Special Programs Guide gives a guide to the
available programs.
The HEAT button selects drying temperature
(see Start and Programs).
In HIGH heat.
Out: LOW heat.
The PROGRAMS knob sets the program: rotate it
clockwise, never counter-clockwise, until the indicator is
pointing to the program you want to select (see Start
and Programs). The program knob will advance to the 0
position after the program ends.
The Drying Guide allows you to consult a user
friendly table of fabric types and load capacities.
5
1950756200 English (US), French (Canadian), Spanish (US) {PDF Created 12/05/09 09:56:00}
Start and Programs
TD4081 Issue 1
6. Press the START button to begin.
During the drying program, you can check on your
laundry and take out the items that are dry while the
others continue drying. When you close the door
again, press START in order to resume drying
Choosing a Program
1. Plug the dryer into the electrical socket.
2. Sort your laundry according to fabric type
(see Laundry).
7. About 10 minutes before the program is completed,
it enters the final AIR FLUFF phase (fabrics are
cooled), which should always be allowed to complete.
3. Open the door and make sure the filter is clean
and in place (see Maintenance).
8. Open the door, take your laundry out, clean the
filter and replace it (see Maintenance).
4. Load the machine and make sure that the items
are not in the way of the door seal. Close the door.
9. Unplug the dryer.
5. Choose a drying program by checking the Programs
table (see Programs) as well as the indications for
each type of fabric (see Laundry). - set temperature
with the HEAT button; - select a program or drying
time by rotating the PROGRAM knob clockwise.
6
EN
1950756200 English (US), French (Canadian), Spanish (US) {PDF Created 12/05/09 09:56:00}
Programs
Program
EN
Timed Drying
(Up to 170 minutes)
Fabric Care
Air Fluff Phase
Fabric Care
TD4087 Issue 1
What it does
Dries wet clothing that will be
ironed, acrylic fibers or small
loads (less than 2 lb / 1 kg).
Heating Elements turn
themselves off and clothing is
cooled down.
Brief program (approximately
10 minutes) that softens fibers
of clothing that is ready for
ironing.
How to set it
1.
Select required Heat setting HIGH HEAT or
LOW HEAT by pressing the HEAT Button.
2.
Position the PROGRAM knob on the desired
time.
Press the start Button..
3.
Note
Consult suggested drying
times (see Laundry)
This is the’ final phase of all programs. Approximately Always allow the dryer to
complete this phase.
10 minutes before the finish, the knob advances
automatically to the Air Fluff phase. After this the
clothing is ready to be taken out.
1.
Select HIGH HEAT by pressing the HEAT Button.
2.
3.
Position the PROGRAM knob on
Press the start Button..
1.
Select HIGH HEAT by pressing the HEAT
Button.
2.
3.
Position the PROGRAM knob on A
Press the start Button..
! This is not a drying
program (see below)
Easy Iron
Fabric Care
Dries completely: your clothes
are ready to be worn
A
Regular Cottons
Automatic Drying
! If you select LOW HEAT,
this program will not dry
your clothes. For Acrylic
fibers or small loads select
Timed Drying.
.
, Permanent Press,.
Easy Iron Program
Easy Iron is a short 10 minute program (8 minutes of heat followed by a 2 minute Air Fluff period) which fluffs the
fibers of clothing that has been left in the same position/location for an extended period of time. The cycle relaxes
the fibers and makes them easier to iron and fold.
! Easy Iron is not a drying program and should not be used for wet articles of clothing.
For best results:
1. Do not load more than maximum capacity. These numbers refer to dry weight:
Fabric:
Max load:
Regular Cottons and Regular Cottons mix
5.5 lb / 2.5 kg
Permanent Press
4 lb / 2 kg
Denim
4 lb / 2 kg
2. Unload the dryer immediately after the end of the drying cycle, hang, fold or iron the articles and put them
away. Should this not be possible, repeat the cycle.
The Easy Iron effect varies from one fabric to the next. It works very well on traditional fabrics like Regular
Cottons or Regular Cotton mix, and less well on acrylic fibers.
7
1950756200 English (US), French (Canadian), Spanish (US) {PDF Created 12/05/09 09:56:00}
Laundry
TD4003NA6 Issue 1
Wash care labels
Sorting your laundry
•
•
•
•
•
Look at the labels on your garments, especially
when tumble drying for the first time. The following
symbols are the most common:
Check symbols on clothing labels to
make sure that the articles can be tumble dried
Sort laundry by fabric type.
Empty pockets and check buttons.
Close zippers and hooks and tie loose belts and
strings
Wring out each item in order to eliminate as much
excess water as possible.
May be tumble dried.
Do not tumble dry.
! Do not load dripping wet clothes into the dryer
Tumble dry at high heat setting.
Maximum load
Do not load more than maximum capacity.
These numbers refer to dry weight:
Natural fibers: 6 kg max (13 lb)
Synthetic fibers: 3 kg max (6.6 lb)
Tumble dry at low heat setting.
What not to tumble dry in your dryer:
• Articles that contain rubber or rubber-like materials,
or plastic film (pillows, cushions, or PVC rainwear);
any other flammable objects, or objects that contain
flammable substances (towels soiled with
hairspray).
• Glass fibers (certain types of draperies).
! Do not overload the dryer as this could result in
reduced drying performance.
Typical weights
Clothes
Cotton
Other
Cotton
Other
Blouse
Dress
Jeans
10 Diapers
Cotton
Other
Shirt
T - Shirt
150g
100g
500g
350g
5 oz
3 oz
1lb 2 oz
12 oz
700 g
1 lb 6 oz
1000 g
300g
200g
2 lb 6 oz
10 oz
7 oz
125 g
4 oz
• Items that have been Dry Cleaned.
• Items with the ITLC code (“Special clothing items”)
. These can be cleaned with special at-home
dry cleaning products. Follow instructions carefully.
• Large bulky items (quilts, sleeping bags, pillows,
cushions, large bedspreads, etc.). These expand
when drying and would prevent airflow through the
dryer.
Household items
Duvet cover
(Double)
Large Tablecloth
Cotton 1500g
Other
1000g
700 g
3 lb 5 oz
2 lb 3 oz
1 lb 6 oz
Small Tablecloth
250 g
9 oz
Tea Towel
100 g
3 oz
Bath Towel
Hand Towel
700 g
350 g
1 lb 6 oz
12 oz
Double Sheet
500 g
1 lb 2 oz
Single Sheet
350 g
12 oz
At the end of a drying cycle, cottons could still be
damp if you grouped cottons and permanent press
items together. If this happens simply give them an
additional short period of drying.
8
1950756200 English (US), French (Canadian), Spanish (US) {PDF Created 12/05/09 09:56:00}
EN
Spec ial c lothing item s
Blankets and bedspreads: acrylic items (Acilan,
Courtelle, Orion, Dralon) must be dried with special care
on a low heat setting. Avoid drying for a long period of
time.
Pleated or creased garments: read manufacturers
drying instructions on the garment.
Starched articles: do not dry these items with nonstarched items. Make sure that as much of the starch
solution is removed from the load as possible before
placing it in the dryer. Do not over-dry: the starch will
become powdery and leave your clothing limp, which
defeats the purpose of starch.
Dr ying tim es
The table below presents APPROXIMATE drying
times in minutes. Weights refer to dry garments:
High (Full) Heat
Drying times 800-1000 rpm in washing machine
Half Load
4 lb
1 kg
2 kg
• Amount of water retained in clothes after spin cycle:
towels and delicates retain a lot of water.
• Fabrics: items that have the same type of fabric but
different textures and thicknesses may not have
the same drying times.
• Quantity of laundry: single items or small loads
may take longer to dry.
• Dryness: if you are going to iron some of your
clothes, they can be taken out while still a bit
damp. Others can be left longer if you need them
to be completely dry.
• Heat setting.
• Room temperature: if the room where the dryer is
located is cold, it will take longer for the dryer to dry
your clothes.
Regular Cottons
2 lb
Times are approximate and can vary depending
upon:
25-35
55-65
Permanent Press
Full Load
7 lb
9 lb
11 lb
13 lb
3 kg
4 kg
5 kg
6 kg
80-95
100-120
125-145
150-170
High (Full) Heat
Drying times on reduced spin in washing machine
Half Load
Full Load
2 lb
4 lb
7 lb
1 kg
2 kg
3 kg
20-35
45-55
65-80
Delicates/Acrylics
Gentle (Low) Heat
Drying times on reduced spin in washing machine
Half Load
Full Load
2 lb
4 lb
1 kg
2 kg
100-115
140-150
TD4088VS6 issue 1
9
• Bulk: some bulky items can be tumble dried with
care. We suggest that you remove these items
several times, shake them out, and return them to
the dryer until finished.
! Do not over-dry your clothes.
All fabrics contain a little natural moisture, which
keeps them soft and fluffy.
1950756200 English (US), French (Canadian), Spanish (US) {PDF Created 12/05/09 09:56:00}
Maintenance and Care
EN
When you should Switch off the
TD4005NA Issue 2
Check the drum after each cycle
electricity
Unplug the dryer when not using it, when cleaning it,
and during maintenance activities.
Turn the drum manually in order to remove small
items (handkerchiefs) that could have been left
behind.
Clean the filter after each cycle
Cleaning the drum
The filter is an important part of your dryer: it
accumulates lint and fluff that is formed while drying.
Small items could also become trapped in the filter.
When finished drying, therefore, clean the filter by
rinsing it under running water or with your vacuum
cleaner. Should the filter become clogged up, the
airflow inside the dryer will be seriously
compromised: drying times lengthen and you will
consume more energy. It may also damage your
dryer.
! Do not use abrasives, steel wool or stainless steel
cleaning agents to clean the drum
A colored film may start to appear on the stainless
steel drum, this may be caused by a combination of
water and, or cleaning agents such as fabric
conditioner from the wash. This colored film will not
affect the dryer performance.
Cleaning the dryer
• External parts in metal or plastic and rubber parts can
be cleaned with a damp cloth.
• Periodically check the vent tube and any
permanent venting fixture to make sure that there
has been no accumulation of fluff or lint, and
remove it.
• Remove lint that collects around filter and the outlet
vents.
The filter is found in front of the dryer trim
(see diagram).
! Do not use solvents or abrasives.
! Your dryer uses special bearing components which
do not need lubrication.
! Have your dryer checked regularly by authorized
technicians to ensure electrical and mechanical
safety.
Removing the filter:
1. Pull the plastic grip of the filter upwards (see
diagram).
2. Clean the filter and replace it correctly.
Ensure the filter is fully located flush into the
tumble dryer trim.
! Do not use dryer without replacing the filter.
10
1950756200 English (US), French (Canadian), Spanish (US) {PDF Created 12/05/09 09:56:00}
Troubleshooting
T D4183 Issue 1
Before you call our Customer care department, go through the following troubleshooting suggestions.
EN
Problem:
Possi ble caus es / Solutions :
The dryer won’t start
It is taking a long time to dry
•
•
•
•
•
The plug is not plugged into the socket, or not making contact.
There has been a power outage.
The fuse has blown.
The door is not closed securely.
The PROGRAMS knob has not been set properly (see Start and
Programs).
• The START button has not been pressed (see Start and Programs).
• The filter has not been cleaned (see Maintenance).
• The temperature setting is not ideal for the type of fabric you are
drying (see Start and Programs).
• Automatic / Sensor Dry Programs require a
HIGH temperature setting (see Start and Programs).
• The correct program has not been selected for this load
(see Start and Laundry).
• The Exhaust Duct is obstructed (see Installation).
• The air intake vent is obstructed (see Installation).
• The permanent Ventilation flap on the storm cover is obstructed
(see Installation).
• The items are too wet (see Laundry).
• The dryer is overloaded (see Laundry).
If you still have a problem ca ll our Custom er Ca re D epa rtm ent on 1 80 0 35 6 07 66
Spare Parts
This dryer is a complex machine. Repairing it yourself or having a non-authorized person try to repair it could cause
harm to one or more persons and to the machine, and could invalidate the spare parts warranty.
Call an authorized service center if you experience problems while using the machine.
Contact number:1 800 356 0766
TD4083 Issue 2
11
1950756200 English (US), French (Canadian), Spanish (US) {PDF Created 12/05/09 09:56:00}
TD4089 issue 3
Installation Instructions
Read these instructions with care.
These instructions are provided for us e by qualified installers, in addition the installation must comply with:
•
In the United States, in accordance with the National Electric Code ANSI/NFPA70 – latest edition and any State,
Municipal or local codes.
•
In Canada, in accordance with the Canadian Electric Code C22.1 – latest edition and any Provincial, Municipal or
local codes
Electrical
The dryer comes with a three cord power supply cord fitted with a 5-15P (plug), a receptacle should be installed in a
location accessible after the dryer is installed.
Grounding
Some local codes may require a separate ground. In such cases the required ground wire, clamp and screw
must be purchased separately.
NEVER ground the dryer to plastic plumbing lines, gas lines or water pipes.
NOTE: IF IN DOUBT ABOUT ANY OF THE ABOVE
CONSULT A QUALIFIED ELECTRICIAN
Where to put your dryer
Check local codes before choosing a location. Some codes do not permit installation in a garage, c loset, mobile home
or bedroom.. DO NOT install the dryer in an area where gasoline or other flammable materials are kept or stored.
W hen operating the dryer, there has to be adequate ventilation to avoid the back flow of gases into the room from
appliances burning other fuels, including open fires.
Minimum installation clearances.
Sides
Top
Rear
Front
Vent Opening –
Distance from
Top of closet
Closet
¾” (15 mm)
½” (10 mm)
¾” (15 mm)
¾” (15 mm)
Closet (alternative)
0
4” (100 mm)
¾” (15 mm)
¾” (15 mm)
Under Counter
¾” (15 mm)
½” (10 mm)
¾” (15 mm)
not applicable
6” (150mm)
2” (50mm)
not applicable
If installed in a closet it must have the following dimensions and have two ventilation openings each having and area 72
sq. ins. (450 sq. cm) located) 2” (50mm or 6” (150mm) from top[see table] and 6” (150mm) from bottom of door.
It must NEVER be installed in a closet with a solid door.
The dryer has adjus table height feet, use these to level the dryer after fitting into its final position.
RV/Marine Installations
W hen locating the appliance in a towable trailer or watercraft, position the dryer over the axles or mid-ship
where movement is at a minimum. Block the dryer to prevent extreme movement or tipping.
12
1950756200 English (US), French (Canadian), Spanish (US) {PDF Created 12/05/09 09:56:00}
TD4178W issue 1
Installation Instructions
Exhaust Ducting
The ducting system for the dryer must be as s hort and straight as possible and with as few elbows as poss ible. Fourinch (102 mm in Canada) rigid metal duc ting should be used, metal flexible ducting can be used but the maximum
length of ducting if used is 7ft (2.4 m). and provided it complies with the following:
In Canada, that only those foil-type flexible ducts, If any, specifically identified for use with the appliance by the
manufacturer shall be used. In the United States, that only those foil-type flexible ducts, if any, spec ifically identified for
use with the appliance by the manufacturer and that comply with the Outline for Clothes Dryer Transition Duct, Subject
2158A, shall be used;
Never use plastic ducting. All elbows must also be a minimum of 4-inch (102 mm) diameter. Joints must be secured
with duc ting tape. Do not use screws or other metal fastenings that extend into the duct as lint can collec t on the
screws.
Maximum length of Rigid duct
Number of Rigid Duct (only)
Elbows
0
22 ft. (6.6m)
1
18 ft. (5.4.m)
2
14 ft.(4.2m)
3
6 ft.(1.8m)
The above assumes that an approved venting hood is used and that the flap on this hood must not have magnetic
catches.
WARNING:
-The appliance MUST NOT be exhausted into a chimney, a wall, a ceiling, a wall, a ceiling, an attic, a crawl space or a
concealed space of a building.
- To reduce the risk of fire, this appliance MUST BE EXHAUSTED OUTDOORS
- Do not discharge the exhaust air into a flue, which is used for exhausting fumes from other appliances
burning gas or other fuel.
Depending on the frequency of use it is ess ential that the ducting is checked periodically and any fluff or debris removed
Stacking Kits
A stacking kit Ariston reference number 66911 is available from your dealer, which allows the dryer to be
fitted to the top of an Ariston washing machine
The kit contains, all the necessary brackets and screws.
Tools needed; - No 2 Philips Screwdriver, 2mm drill, power or hand drill
SAFETY
For personal safety, DO NOT try to fit the dryer on top of the washing machine on your own. A
second person should help to lift the tumble dryer onto the washer, and to relocate the stacked
washer and dryer.
1. You will need to get to the sides of the washing machine to fit the stacking kit and
dryer. If necessary pull the machine away from its location to gain access to the machine to fit the stacking
kit and dryer.
2. Follow the instructions provided with the stacking kit.
Alternative stacking kit.
RV/Marine Stacking Kit ~SK02 available from Westland Sales: 1-800-356-0766
13
1950756200 English (US), French (Canadian), Spanish (US) {PDF Created 12/05/09 09:56:00}
T D4084 issue 3
ARISTON ONE-YEAR LIMITED WARRANTY
(USA & CANADA ONLY
WHO IS COVERED BY THIS WARRANTY
This limited one -ye ar warr anty (“ Wa rranty”) is given only to the or iginal end-use/retail pur chaser (the “F ir st Using Purc ha ser”) of the
ac companying Ar iston pr oduct(s) (the “Ariston Product”).
If you pur chased this Ar iston Product fr om som eone othe r than an a uthorized Ariston r eseller /de aler in the United Sta te s or C anada , or if
the Ariston Pr oduc t was used (inc luding but not lim ite d to f loor models or re furbished pr oducts) pr ior to your purchase, then you ar e not
the F ir st Using Purcha se r a nd the Ariston Pr oduct that you purc ha sed is not c over ed by this War ranty. This War ranty is not tr ansfera ble.
WHAT IS CO VE RED B Y THIS W ARRANTY
Ariston will repa ir or replace a ny pa rt of the Ariston Product which fa ils due to a de fect in mater ials or workmanship whe n used under
norma l hom e-use conditions. Ariston will also provide, f ree of charge, a ll la bor to r epair or r epla ce the def ective pa rt.
This Wa rranty applies only to Ariston P roduc ts pur chased a nd used in the United S tates or C anada. S ubjec t to the exclusions below, for
Ariston Products purc hased in, but used outside, the United S tates or Ca nada, this Warr anty covers only warr anty service within the United
State s or C anada (a nd does not include shipping outside the United Sta te s or Cana da ).
LENGTH OF THE WARRANTY
This Warra nty runs f or a per iod of one (1) year f rom the date of the original pur chase by the First Using Purc haser. P le ase note that a copy
of your original pur chase re ceipt showing the purchase date and the vendor’s name and address are r equired to obtain service under this
Warr anty. For the purposes of deter mining the a pplica ble warr anty period, please note that any a nd all r epla ced or r epaired parts sha ll
assume the identity of the origina l.
WHAT IS NO T COVERED BY T HE WARRANTY (EXCL USIONS)
This Wa rra nty does not cover:
1. Improper insta lla tion, delive ry, maintenance a nd/or improper oper ation of the Ariston Product. 2. Dama ge c aused if the Ariston Pr oduct
has not been used in compliance with the electricity or gas supply spe cifica tions printed on the r ating pla te. 3. Failure of or dama ge to the
Ariston Product if it is altered, abused, misused, or used for other than the inte nde d purpose, or if it is used comm ercia lly. 4. Ser vice trips to
your home to provide instr uctions on the use of your Ariston Product. 5. R epla cem ent of house fuses or corre ction of the plum bing or
electr ic wiring in your home . 6. Dama ge ca use d by neglect, ac cident, fire, floods or ac ts of God.
7. Physic al Da mage to the a ppe ara nc e of your Ariston Product inc luding, without lim ita tion, scr atches, rust, dents, warping, pe eling and
the like. 8. Dam age caused by tr anspor ta tion.
9. Replace ment of any consum able or de gr adable item or ac cessory including, but not lim ite d to: plugs, ca ble s, batteries, light bulbs,
fluorescent tubes and star ters, covers and f ilters, or replac ement of a ny removable pa rts m ade of glass or pla stic.
10. Dama ge c aused a fter delivery. 11. Water dam age of any kind.
12. An Ariston Product not a cce ssible to pr ovide required se rvic e.
13. Problems arising from other tha n defe cts in m ateria ls or workmanship.
14. Travel time when installe d in a r ecre ationa l vehicle or ma rine a pplica tion.
This Wa rra nty is void if the Ar iston P roduc t is a lter ed, serviced, m ainta ined, dism antle d, or otherwise interfe red with by a ny person who
is not a uthorized by Ariston.
15. Non- sta nda rd labor whe n insta lled in a ma rine a pplica tion.
16. Water le aks of any kind
TO THE EXTENT PERM ITTED BY LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WAR RANTIES, WRITTEN OR ORAL,
WHETHER EXP RESSED BY AFFIR MATION, PR OM ISE, DESCR IPTION, DRAWING, M ODEL OR SAMPLE. ANY AND ALL
WAR RANTIES OTHER THAN THIS ONE, WHETHER EXPR ESS OR IMPLIED, INC LUDING IMP LIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURP OS E, ARE HER EB Y DIS CLAIM ED. IMP LIED WAR RANTIES
INCLUDING, BUT NOT LIM ITED TO, THE IMPLIED WAR RANTIES OF M ER CHANTABILITY AND FITNES S THAT CANNOT BE
EXCLUDED BY LAW, S HALL BE LIMITED TO THE S AM E DUR ATION AS THIS WAR RANTY. EXC EP T FOR THAT R EPAIR OR
REPLACEMENT AS DESCR IBED ABOVE, ARISTON SHALL NOT B E LIAB LE FOR ANY DIRECT, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR SP ECIFIC RELIEF .
Some States a nd Provinc es do not allow the exclusion or lim ita tion of incidental or c onsequential dam ages and/or implie d wa rranties, so
the above lim ita tions or exclusions may not a pply to you. This War ranty gives you specific legal rights and you ma y a lso have other legal
rights whic h vary from State to State or Provinc e to Provinc e.
WHAT YOU SHOULD DO TO OBTAIN WARRANTY SERVICE
All repairs or war ranty service must by pr ovided by Ariston or an Author ized Ariston Ser vic e C enter.
To schedule warra nty service please ca ll 1-8 00-356-0766, ema il service@westlandsales.com. Please rem ember to provide us with your
Ariston Product’s m ode l number and ser ial number .
Plea se note that a c opy of your original pur chase re ceipt showing the purchase da te and the vendor’s name and a ddr ess a re required to obtain
service under this Warr anty. If the Ariston Pr oduct is located in a n ar ea whe re service by an Authorized Ar iston S ervice Ce nter is not
available, you ma y be responsible for a trip char ge or you ma y be required to br ing the Ariston Pr oduct to an Authorized Ariston S ervice
Ce nter f or service .
The foregoing are your sole (i.e., only) a nd exc lusive r emedies unde r this War ranty. This War ranty is the only war ranty that Ariston is giving
for this Ariston Pr oduct. This War ranty replace s all other agreem ents a nd under sta ndings that you m ay have with Ariston or its
repr esentatives.
14
1950756200 English (US), French (Canadian), Spanish (US) {PDF Created 12/05/09 09:56:00}
2