WangYe WY50QT-10 User manual

USER MANUAL
Motorcycle Operating Manual Model: WY50QT-30A
PREFACE
Thanks for your purchasing the motorcycle WY50QT-30A, and
sincerely welcome you to be our motorcycle user. To enjoy a more safe
and pleasurable driving, at first please familiarity with the manual must
carry on before driving. Your personal safety depends not only the
vigilance and familiar operation skills, but also relates to whether you
are familiar with the mechanical performance. Before driving, check-up
and periodical maintenance are basic requirement. If maintenance and
repair needed, go to our service center for help. If you know the
mechanic knowledge and have the tools, the dealer can offer you help
with the maintenance and repair, like providing the parts catalogue and
the spare parts.
This manual explains in detail the correct operation and maintenance,
together with the expectation for your long-time use. Modifications in
specification could cause the discrepancy with some figures and content
in the manual, we feel sorry for that and hold the final right of
interpretation.
Have a good enjoyment and thanks again for your purchasing.
The important points to attention
Ÿ
The driver and passenger
This motorcycle was limited to one driver and one passenger (except children younger than 12 years old).
Never exceed the Max load capacity of motorcycle.
Ÿ For the safety, avoid driving the motorcycle in atrocious weather or cold weather (under -12℃).
Ÿ For the road condition
This kinds of motorcycle can only drive on the highroad.
The caution banners about the safety or environment protection stick to the sundries box cover, the rear
carrier, and fuel tank cap. (Being visible before or during driving)
• Please carefully read the user manual
You must attention to the warning sentence or paragraph.
WARNING:
Not following the operation instruction in this manual may cause great damage to you.
ATTENTION:
Not following the operation instruction in this manual may cause injury to both you and vehicle.
Regard this manual as a permanent parts, even when transfer the vehicle to a new owner, transfer the
manual at the same time.
LIST
Ⅰ. Motorcycle safe drive
Rules for safe drive………………………1
Payload………………………………2
Ⅱ.The parts&subassemblies and use
instruction
Parts&subassemblies………………………3
speedometer and indicaor…………………5
Ignition switch………………………………5
Fuel meter …………………………………6
Headlamp switc h…………………………6
Starting switch ……………………………6
Main beam switch…………………………7
Turning signal light switch…………………7
Horn switch…………………………………7
steering handle lock………………………8
Seat lock……………………………………8
Ⅲ.Operation guide
Checking before driving……………………9
Starting engine……………………………13
Driving motorcycle………………………14
Driving operation…………………………15
Braking operation…………………………15
Engine power off operation………………16
Stopping motorcycle……………………16
Ⅳ.Service and maintenance
The table of periodic mantenance………17
simple trouble solution……………………20
Cleaning the air filte r……………………22
Battery mantenance ……………………22
Adjusting Idling speed……………………23
Replacing gearbox oil …………………24
Spark plug ………………………………25
Replacing fuse …………………………25
Ⅴ.Vehicle storage ……………………26
Ⅵ.Vehicle identification ………………27
Ⅶ.Tool set ………………………………27
Ⅷ.Main technique date…………………28
Ⅸ.Circuit diagram………………………30
Ⅹ.Emission Control System
Warranty Statement………………………31
Ⅰ. Motorcycle safe drive
Rules for safe drive
1. The motorcycle happen the many accident, all reasons are that the car drivers
didn’t look at the motorcycle drivers. So the motorcycle drivers must:
l
Put up the coat in bright color
l
Avoid to the driving at night .you must drive on guard and carefully to the
strong light.
2. Particular care should be exercised at the level crossing of roads, entrance and
exit of parking lot or on the automobile lane.
3. Don’t speeding, because the speeding usually to happen an accident.
4. You must get to the driving license and familiar with motorcycle. Never lend
motorcycle to the man without driving license or unfamiliar with motorcycle.
5. Avoid to driving the road with accidental, easily result in the operation without
used or the part was broken.
6. You must check up the motorcycle before driving.(Ref Page9).
During drive, grasp the left hand bar by the left hand and the throttle twist grip by
the right hand with feet on the footrests.
1
Payload
l warning:
The light goods can only put in the rear shelf or other deposited place.
The goods payload not heavier than Table 1:
table 1
Deposited
Weight (kg)
Rear shelf
5
l
l
l
The motorcycle max payload is 75kg,including the weight with the driver,
the passenger, the goods.
If the motorcycle is over loading, it can affect the stability and operation of
the motorcycle.
The goods on the motorcycle, must tie it.
2
Ⅱ.Parts&Subassemblies and use instruction
Parts&Subassemblies (Fig1.Fig2)
Fig.1
3
Fig2
Dashed(……)Indicate the not see parts directly
4
Meter and indicator light (Fig3)
⑴Odometer
⑵Speedo meter
⑶Fuel meter
⑷Parking light
⑸Right Turning signal light
⑹Voltage Meter
⑺Left Turning signal light
(8) High-Low beam light
⑼Time meter
Fig3
Ignition Switch(Fig4)
(1) On ( )-when the switch turn to this position,
Start engine and do not pull out the key.。
(2) Off ( ) When the switch turn to this position,
Start engine power off and take out the key.
⑶ Lock ( ) When the switch turns to lock position ( ),
Take out the key .do not do any turning operation
And do not start engine and light.。
Notice :If the engine is idling speed for a long time in the hot climate,
It will appear too hot Phenomenon Must close engine.
Fig 4
5
Fuel Meter(Fig 5)
1.Fuel Meter (Fig 5) show the approx remainder of flue. When
the hand point to (F), it indicates Full tank of 7.5L.。
2.When the hand at red section it indicates the remainder of flue is 1.8L.
Headlight Switch (1)(Fig 6)
Headlight switch: three position“ ” 、
“
”and“•”
Fig5
:When it on the position, the front head light, tail light, position light and meter light turn on.
:When it on the position, tail light, position light and meter light turn on.
•:When it on the position, the front head light, tail light, position lighted instrument turn off.
Starting Switch (2)(Fig 6)
Press this button to start engine(Ref.P16)
Fig6
6
Main beam switch (1)(Fig 7)
Press“
”button,is main beam;Press“
”button isdipped beam。
Turning signal light switch (2)(Fig 7)
When the switches on ( ) ,the left turning signal light turn on.
When the switch on ( ), the right turning signal light turn on,
Press it down the light turn off.
Horn Switch (3)(Fig 7)
Press this button, the horn makes sound.
Fig 7
7
Steering handle lock(Fig8, Fig9)
Turn handle left to end, presses down ignition key1 to ( ), the steering device are locked Do
the above opposite it opened.
Fig 9
Fig 8
Seat Lock(Fig 10)
Put the key into seat lock hole and then
clock-wise open the lock.。
Press down the multi-purpose until it make
sound of locked, then push the back of
multi-purpose to confirm it has been locked
and take out the key.
Fig10
8
Ⅲ.Operation guide
Checking before driving:
For safety and prevent trouble or accident,
Pre-check up is necessary.
Fuel
When the pointer or fuel meter is close to red section,
replenish oil; meanwhile, check the Fuel Tank and
Carburetor rack or not
Fuel Tank:7.5L
•
Clock –wise to open the tank cover.(Fig 11)
•
Suggestion gasoline: octane number is 90
•
Do not replenish gaoline together with tidy or water
NOTICE:
Fig 11
If check gasoline volume or replenish gasoline soon after stop, Beware of
burning.
Keep gasoline level under away from the height panel of fuel tank while
replenishing.
If gasoline level is too high, it is easy to leak out.
If swallow the gasoline careless, see the doctor at once.
9
Checking engine oil
checking engine oil level(Fig 12、Fig 13)
1.Keep the motor steady in the flat ground, then use the
key to open the cover .
2. Open the cover of Oil tank, Check the oil
Volume, the capacity of engine oil: 1.2L
Fig12
Suggestion the engine oil:
special 2T oil(FC lever)
Fig13
10
Free Path of Rear Brake(Fig 14,Fig15)
Measure the distance of rear brake pedal before detent function .the free
path should between 20-30mm, take the tail of brake handle as standard.
Fig14
Fig15
11
Tire
Check the tire pressure regularly and adjust.
Check before the tire cooled
Check if there any metal trash or gravel in the groove of tires
WARNING:
If the tire pressure dose not accord with the standard, it will properly cause
the traffic accident.
It is dangerous that use the worn tire; It will have effect to friction between tire
and rode. Maybe make difficult from drive or accident.
12
Starting engine (Fig 17)
• Preparative before starting:Set up the Main Stand,Put
the key into ignition switch and turn to “ .
Electric starter:Press start button (1) to start engine, DO
not use the starter more than 5 seconds each time.
NOTICE:
Electric starting is only in the condition of grasping the brake handle.
Fig17
Electric starting not succeed, if starting again with it, we must stop for 30 seconds, If still
can’t start, Please use kick-start.
Engine kick-start :open ignition switch and add gasoline slowly, step kick-starter pedal
down quickly with strength to start engine.
Notice: After using kick-starter pedal, pull it back to original position. Otherwise
have effect to safety ride, and bad to engine.
Had better not open ignition switch when scooter has not use for a long time, and first
step kick starter for some times. Make flue into carburetor and then into cylinder, and
open ignition switch, Start engine, it is easy to start engine like this.
If cold start warm up engine for 2-3 minutes.
13
Driving motorcycle:
WARNING:
Wear the trousers to avoid touching with exhaust pipe and was burnt.
The entire device must be installed according to requirement of the
traffic rule.
Take the license to riding.
NOTICE:
Control the speed and load during 1000km of running in period. Load should
be within 100kg(including driver) If take more weight and speed will reduce
life of engine,
Speed according to (Table 2)
Leg(km)
0~200
200~500
Speed (km/h)
≤20
≤30
14
Table 2
500~1000
≤35
Driving operation
Release rear brake level, add gasoline slowly with throttle grip, then motorcycle will
move forward smoothly.
NOTICE:
Do not add much gasoline suddenly with throttle grip to prevent motorcycle rush out.
Maybe lose control.
• Before drive, must take the stand.
Braking operation:
1 Control throttle grip
If want to reduce speed, Must control the throttle grip, at that time use the two-brake
system, this point is very important.
Notice: if the drive will be done in this situation, for example: damp or loosely
roads, raining .no matter brake, add speed or turn must take care.
2.operate front and rear brake.
Notice: Must totally close the flue when drive in a descent, and use two-brake
system for reduce speed. Don’t use brake continuously, other wise it will reduce
the effect of brake because of too hot.
Warning: Don’t use single brake when drive with high speed, special crooked and
slippery road. Must use two-brake system for avoiding accident.
15
Engine power off operation (Fig18, Fig19)
Turn off Throttle:Revolve to the lowest place according to picture. (Normal situation is
loose the throttle grip, and the engine is idling speed)
• Put the key to “
”
Fig18
Fig19
Stopping operation:
When the motorcycle stop, put the key to “ ” position .put down stand and lock handle.(Ref P7
Warning:Motorcycle should be park on the Solidity and Flat ground, otherwise, it maybe
make some body injured or vehicle down
Alarm points:
1 Locking the handle and do not left key in the switch
2 Put the motor into the garage
3 Use the excellent guard against theft device
16
Ⅳ.Service and maintenance
Maintenance periodic form
The maintenance is important to motorcycle, If drive with high speed in bad situation for
a long time, must add the times of maintenance, If motorcycle have a big repaired or a
accident, Must take it to check for mainly spare parts. For example: frame, indicator
parts and so on. Repair or change the worn parts. Make sure safety.
Notice: Don’t change motorcycle make sure it’s safety, Must use good quality spare
parts if replace spare parts .if use bad quality spare parts, it will influence the safety of
motorcycle.
Warning: Must close engine when make maintenance .it make sure the repairer’s
safety. And put down the stand on the smooth ground.
Notice: Must make a good maintenance if the motorcycle don’t use over a month, or
don’t use in all the winter. Make flue, tire and battery avoiding corrode.
17
Maintenance periodic blank (table 3):
Check before time based maintenance(Ref P9)
I:Check and adjust when necessary
C:Clean
R:Change
table 3
Cycle
1
Item
Every Month
﹡
﹡
﹡
﹡
﹡
Fuel Pipe
I
I
Throttle
Element
of
air
Note1
Spark plug
Carburetor idle
I
18
Speedometer(×1000km)
4
8
12
6
12
18
I
I
I
I
I
I
C/1000km, if need: R
C/2000km,If need: R
I
I
I
Ref
Page
15
22
26
23
Blank3
Cycle
1
Item
Every month
﹡ Transmission belt
﹡ Gearbox oil
Brake system
Brake Switch
Headlight
﹡
Suspension
﹡
﹡ Bolts&Nutsfasten
Wheel, Tyre
﹡
Turning
bearing
﹡
Speedometer(×1000km)
4
8
12
Ref
Page
6
12
18
Per1000km I
Note3
(300km)R
I
I
I
I
I
I
Note2
I
If need: R
I
I
I
I
I
I
I
I
I
I
I
I
I
I
25
11
12
*If you have all of tool and maintenance document, you are a mechanic person, or else
must let special person maintenance and repair.
**For safety, we claim all of items have done by mechanic person.
Note: 1.Iif this area is very damp or have a lot of dirty .you had better make a short time
for maintenance, when it take more oil quantity or not strength, it must change.
2.If it was used every day, must make maintenance.
3. According to season to change in a cold area.
19
Simple trouble solution (table 4)
Table 4
Complaint
Symptom and possible causes
Plug not
sparking
Engine
does not
start
Spark
plug is
weak
No mixed
air in
cylinder
Cylinder
compresses
strength low
solution
Damaged spark plug
Damaged Ignition Coil
Defective CDI
Defective ignition switch
Renegade or loosely Ignition system
Replace
Replace
Replace
Replace
Spark plug gap too small or big
Spark plug pole burn
Adjust
Replace
Spark plug accumulates carbons
Clear out
Fuel use out
Replenish
Oil mouth stop up
Dredge
Fuel tank switch wear
Change
Fuel path stop up
Dredge
Air filter stop up
Clean the air filter element
Intake system leak
Check and clear out
Spark plug seat leak
Cylinder cover leak
Tighten spark plug
Change washer
Piston ring & cylinder wear badly
Change piston or cylinder
Piston ring break/ unused Carbon block
Change piston ring / clear out carbons
20
Connect well or tighten
Table 4
Complaint
The vehicle
is unable to
accelerate
performance
badly
Symptom and possible causes
Change fuel
Oil path stop up
Clean oil path
Ignition time is too early or too late
Check coil and change CDI
Spark too weak or flameout
Check ignition and clear out
Mixed air too dense or race
Clean& adjust carburetor
Engine leak
Check and clear out
Muffler stop up
Dredge
Belt wear
Turning bearing gap too wide
Replace
Replace
Replace
Replace
Charge
Adjust
Lack of tire pressure
Pump
Front& rear Axle flexible
Tighten nut
Replace
Replace
Replace
Adjust
Automatic clutch roller wearing
Electric
start failure
Clutch worn
Starting relay worn
Electric quantity lack
Driving
unsteady
Brake
Failure
solution
Octane value of the fuel is too low
Brake pad fray to limit
Brake cam fray
Brake cable damaged
Free path overlong
21
Cleaning air filter(Fig 20)
• Take out rear protecting bar left protecting bar
• Take apart air filter cover and screw up bolt.
• Take out filter element
• Compress air or use dry brush to clean filter
element.
• Do the above opposite to reinstall the air filter.
NOTICE:
•
Do not use gasoline or low burning point solvent to
clean paper filter element.
•
When take out the rear protecting bar& left protecting
bar, please under the guiding of Professional
Battery maintenance(Fig 21)
Fig20
It is adopted the airtight battery (don’t add water).
Notice: Do not take apart the airtight
•
If the motorcycle have not been used for a long time.
Taking off the battery and putting it into a dry and place.
•
The head of battery was corroded, please take it off and
clean. (Can use boil water)
NOTICE: turn off the ignition switch, take apart negative pole ○
+ when you are installing.
first, but install positive pole ○
Fig 21
22
Adjusting Idling speed(Fig 22, Fig23)
The carburetor is in the best situation before sold, if the
carburetor is still influence riding
Please adjust it under the instruction of professional man.
• Warm up few minutes before start。
• Idle to adjust screw (1) is it is it improve idle speed slightly to
enter to fasten, is it is it
Withdraw it than screw slowly after stocking to fasten to mix
and then rapidly, to stabilizing the position at most, then
withdraw slowly, get and stabilize the position the most low.
•
After adjust idle, then adjust accelerograph handle
to free path for 2-4mm,then use adjustor (2) to adjust,
screw down nuts, and then screw up it after adjust.
• Adjusting the good idle speed, when should be able to
suddenly strengthen the throttle, the rotational speed of the
engine should be excessively steady, no flash back and can't
go out, stop working or arrange organ not to blow out at being
last throttle.
Fig 22
Fig23
23
Replacing gearbox oil (Fig 25)
Suggestion engine oil No: SAE 80W/90
Oil container
Resolving capacity:0.11mL
Changing capacity :0.10 mL
1
•
Make the motorcycle on the Stand
•
Take apart the immiting bolt (2), and the spilling bolt (1).
NOTICE: The engine must be warmer when
spilling and the vehicle must be steady by main
stand. Make sure the Engine is empty
•
Reinstall the spilling bolt after clean. And screw up.
•
Inject 100ml to engine through immit bolt
•
Install immit bolt and screw up.
24
Fig 25
Spark plug (Fig 26)
Specification of spark plug:
BPR7HS ,BP7HS (NGK), E7TC , E7RTC
•
Take apart the spark plug; Take it of with special tool.
Examine if there is dirty on poles and the
porcelain head in center .If it has corroded, must
change it .It is the best way to clean with the liquor
of spark plug Use wire brush if no cleaner
•
Normally the gap between side electrode (1) and
Center electrode (2) is 0.6-0.7.
•
Don’t use other spare plug.。
1
(0.6~0.7)mm
2
Fig26
Replacing fuse
The specified electric current of the total fuse is 15 A
If the connection is not good, the fuse will overheat and breakdown.
Do not use any fuse whose specification is different from assigned. It is the same
Main reason for wiring burning.
NOTICE: Do not use brass wires to replace the recommended.
25
Ⅴ.Vehicle storage
Storage
For the motorcycle not to be used for a long period of time, for example, in wintertime, some
steps should be taken to prevent malfunction of and damage to its components, which might be
caused by long storage. Besides, before the long storage, proper maintenance has to be carried
out for fear that it might be forgotten when vehicle is put back into use after storage.
1. Change engine oil and oil filter.
2. Drain off fuel from the fuel tank and carburetor, spray atomized anti-rust oil onto the inside wall
of the tank and then close the tank.
Warning: Gasoline is inflammable and may cause fire and even explosion under certain conditions.
Therefore, do not smoke, make fire or have any fire left behind on draining off fuel.
3. Take out the spark plug, pour about 15~20ml clean engine oil into the cylinder, step down the
kick lever repetitively for several times so as to have machine oil distributed all over the engine
and finally fit the spark back on.
Attention: The ignition switch must be set to ”OFF” position before stepping down the kick lever. To
protect the ignition system from damage, the spark plug should be inserted in its cap and
earthed.
4. Wash the motor, wipe it dry and apply an even coat of wax to the painted surface. Chromate
treatment can prevent the surfaces from rusting.
5. Inflate the tires as required and pad the vehicle up by wooden blocks with the two wheels
clearance of the ground.
6. Put the vehicle in a shady and cool place free from humidity and direct sunshine and cover it
properly (but not with plastic or other painted materials).
Reuse motorcycle.
Clean the motorcycle, if the storage time beyond 4 months, Must change gasoline.
Must charging if need, and then install battery.
Must check all of terms before drive (Page 9), for the safety must try the motorcycle with lower
speed for some time in a not busy rode.
26
Ⅵ.Vehicle identification
Vehicle type, Code and trademark of the bikes(Fig27)
When the bikes are registered or getting the license from the transport department, the
owner should be send the VIN number and engine number。The maintain people
change the parts, need the numbers too.
The products brand should be added at the right side plate of the Main stand(see P3).
Fig27
Ⅶ.Tool set
Tool bag(Fig 28)in the boot of seat, Using for the urgent accident
when driving, it including the something of the following:
8×10mm spanner
Screw drive
Wrench bar
12×14mm spanner
Hexagon spanner
18.5×17mm wrench spanner
4
1
Fig28
27
Ⅷ.Main technique parameter
Item
Data
Item
Front tyre
Rear tyre
Air Pressure, Fr tyre
Air Pressure, Rr tyre
L×W×H mm
Wheelbase mm
Ground Clearance mm
Dry weight kg
Max Load kg
Brake Distance mm
2050×680×1209
1440
90
105
75
≤4(30km/h)
Turning angle of steering
handle
≤48°
Engine Type
Max Speed km/h
Consumption L/100km
Climb ability
º
Light vertical angle
Starting system
≤55km/h
≤2.0L/100km
≥4.5
-1.3%
Electric &Kick
Separate lubricative
3.0kW/7000(r/min)
3.9N.m/6500(r/min)
7∶1
Bore×stroke mm
Displacement
Clutch
Fuel tank
L
Battery
Fuse
Headlight
Lubricative system
Rated power
Maximum torque
Compression ration
Spark Plug Model
Transmission system
Gear ratio
BPR7HS BP7HS(NGK)
、
E7TC or E7RTC
28
Table 5
Data
120/70-12
120/70-12
150 kPa
200 kPa
CVT
10.83-33.85
1PE40QMB, Air-cooled, 2 stroke,
Single Cylinder
40.0×39.2
49.3 ml
Automatically centrifugal
License light
7.5
12V 7Ah
15 A
12V18W/18W×2
12V P21/5W
12V 5W
Direction light
12V 10W×4
Taillight/stop light
Table 5
Item
Data
Item
Spark plug gap mm
Idling speed r/min
Engine oil L
Fuel
0.6~0.7
Ignition System
(1800±180)r/min
Special 2T oil (FC level) Gearbox oil
Capacity of engine oil
1.2L
Capacity of gearbox
oil
29
Ⅸ.Circuit
30
Data
RQ90 above
CDI
SAE 80W/90
0.1L
Ⅹ.Emission Control System Warranty Statement
Wangye USA Co., LLC is pleased to explain the emission control system warranty on
Highway Motorcycle. New Highway Motorcycle must be designed, built and equipped to
regulations and standards of the United States Environmental Protection Agency and the
California Air Resource Board and free from defects in material and workmanship that may
keep it from these requirements in the all applicable regulations.
Wangye USA Co., LLC must warrant the emission control system on the highway motorcycle
for 5 years or 6,000 km, whichever comes first, provided that there has been no abuse, neglect
or improper maintenance of highway motorcycle.
1. Period of Warranty
The period of warranty shall be one year on delivery, during this period of warranty:
(i). Any part defective by reason of the manufacturer’s faulty workmanship or material will be
replaced or repaired free of charge;
(ii). Any repairs or adjustments made necessary by reason of the manufacturer’s faulty
workmanship or material will be performed free of charge.
Emission control system may include parts such as the carburetor or fuel injection system, the
ignition system, catalytic converter and engine computer, if it is equipped. Also included may
be hoses, belts, connectors and other emission-related assemblies.
2. Responsibilities of Customer
To obtain repairs under warranty, the customer must:
(i). Ensure that the motorcycle is properly operated, maintained and stored as specified in the
31
Owner’s Manual;
(ii). Give notice to dealer approved by Wangye USA Co., LLC or other qualified service facility
of any and all apparent defects immediately upon discovery, and make the entire
motorcycle available at the time for inspection and repair at the dealer’s place of business;
(iii). Provide proof of warranty coverage to dealer;
(iv). Authorize the dealer to tear down the motorcycle for diagnostic evaluation should it be
required.
All warranty repairs must be done by the dealer and final approval of any repairs rests with
Wangye USA Co., LLC. All parts replaced become the property of Wangye USA Co., LLC.
3. Exclusion
This warranty does not cover the repair or damage resulting from abuse or neglect of the
motorcycle. Examples of abuse and neglect include, but are not limited to:
(i). Racing and competition;
(ii). Use of lubricants, oils and fuel/oil mixture other than those recommender in the Owner’s
Manual, improperly installed accessories and use of parts or accessories that are not
equivalent in design and quality to genuine Wangye parts;
(iii). Damage as a result of accidents, collisions, contact with foreign materials, impact,
submersion or use of the motorcycle after discovery of a defect;
(iv). Appearance-related damages of body parts. Examples of such damages include but are not
limited to: scratches, dents, fading, flaking and peeling;
(v). Motorcycle which has been modified in any way from the standard specifications shown in
the Owner’s Manual, for example, the odometer has been altered;
(vi). Normal wear and tear, corrosion and routine maintenance, such as the recommended
service inspections;
(vii). Pre-delivery inspection and assembly;
32
(viii). Damage from theft, fire, vandalism, explosion, water or acts of God.
4. Restriction
This warranty is in addition to, and not a modification of, any legal warranty required by the
laws of any state of US.
Subject to any applicable sales or consumer legislation, the above warranty is in lieu of any
warranty or representation, express or implied, including any warranty of performance,
merchantability or fitness for a particular purpose on the part of Wangye USA, and any other
obligation or liability on behalf of Wangye USA, and the above warranty constitutes your sole
remedy and the full liability of Wangye USA. In no event shall Wangye USA be liable for
special, incidental or consequential damages howsoever caused, whether by negligence or
otherwise resulting directly or indirectly from the use of the Motorcycle, or the Motorcycle’s
having replacement parts or the unavailability of replacement parts. Wangye USA does not
assume or authorize any person to create or assume for Wangye USA any obligation or liability
in connection with the Motorcycle or any part thereof distributed by Wangye USA.
5. Contact
For any questions regarding emission control system warranty, please contact as following:
Company Name: Wangye USA Co., LLC
Address: 1170 Corporate Dr. West Ste. 204, Arlington, TX 76006
Tel: 817-640-1108 ext 219
Fax: 817-649-5006
33