SP7060-series-rev-5-parts-manual

Parts Manual
StreetPro SERIES
MODELS
SP706016
SP706020
SP706026
SP706030
SP706036
PROFESSIONAL PAVEMENT SAW
(DEUTZ BF3L2011 DIESEL ENGINE)
Revision #5 (05/06/11)
To find the latest revision of this
publication, visit our website at:
www.multiquip.com
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
P/N 38267
PROPOSITION 65 WARNING
Engine exhaust and some of
its constituents, and some dust created
by power sanding, sawing, grinding,
drillingandotherconstructionactivities
contains chemicals known to the State
of California to cause cancer, birth
defects and other reproductive harm.
Some examples of these chemicals are:
Leadfromlead-basedpaints.
Crystalline silicafrombricks.
Cementandothermasonryproducts.
Arsenicandchromiumfromchemically
treatedlumber.
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to
these chemicals: ALWAYS work in a
well ventilated area, and work with
approved safety equipment, such as
dust masks that are specially designed
to filter out microscopic particles.
PAGE 2 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
SILICOSIS/RESPIRATORY WARNINGS
WARNING
WARNING
SILICOSIS WARNING
RESPIRATORY HAZARDS
Grinding/cutting/drilling of masonry, concrete, metal and
other materials with silica in their composition may give
off dust or mists containing crystalline silica. Silica is a
basic component of sand, quartz, brick clay, granite and
numerous other minerals and rocks. Repeated and/or
substantial inhalation of airborne crystalline silica can
cause serious or fatal respiratory diseases, including
silicosis. In addition, California and some other
authorities have listed respirable crystalline silica as a
substance known to cause cancer. When cutting such
materials, always follow the respiratory precautions
mentioned above.
Grinding/cutting/drilling of masonry, concrete, metal and
other materials can generate dust, mists and fumes
containing chemicals known to cause serious or fatal
injury or illness, such as respiratory disease, cancer,
birth defects or other reproductive harm. If you are
unfamiliar with the risks associated with the particular
process and/or material being cut or the composition of
the tool being used, review the material safety data
sheet and/or consult your employer, the material
manufacturer/supplier, governmental agencies such as
OSHA and NIOSH and other sources on hazardous
materials. California and some other authorities, for
instance, have published lists of substances known to
cause cancer, reproductive toxicity, or other harmful
effects.
Control dust, mist and fumes at the source where
possible. In this regard use good work practices and
follow the recommendations of the manufacturers or
suppliers, OSHA/NIOSH, and occupational and trade
associations. Water should be used for dust
suppression when wet cutting is feasible. When the
hazards from inhalation of dust, mists and fumes cannot
be eliminated, the operator and any bystanders should
always wear a respirator approved by NIOSH/MSHA for
the materials being used.
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 3
TABLE OF CONTENTS
SP7060 StreetPro Series
Professional Pavement Saw
Proposition 65 Warning................................................... 2
Silicosis/Respiratory Warnings........................................ 3
Table of Contents............................................................. 4
Parts Ordering Procedures.............................................. 5
Explanation of Code in Remarks Column....................... 6
Suggested Spare Parts................................................... 7
Nameplates and Decals...............................................8-9
Control Panel Decals................................................10-11
Electrical Control Assembly......................................12-13
Console Mounts Assembly.......................................14-15
Rear Console Access Panel Assembly....................16-17
Light Connector/Dash Access Assembly..................18-19
Belt and Engine Guards Assembly...........................20-21
Depth Indicator/Stop Switch Assy. (Old Style)..........22-23
Depth Indicator/Stop Switch Assy. (New Style).........24-25
F-N-R Assembly.......................................................26-27
Fuel Assembly..........................................................28-29
Battery Assembly.....................................................30-31
Stay-Level Handlebars Assembly.............................32-33
Handlebar Boot Assembly........................................34-35
Water System Assembly...........................................36-37
Engine Assembly......................................................38-39
Throttle Control Assembly........................................40-41
Engine Mounts Assembly.........................................42-43
Air Cleaner Assembly...............................................44-45
Muffler Assembly......................................................46-47
Lift Bail Assembly.....................................................48-49
Platform Guards/Rear Pointer Assembly..................50-51
Wheel Drive Assembly.............................................52-53
Front Axle Assembly.................................................54-55
Hydraulic System Assembly.....................................56-57
Engine Pivot Cylinder Assembly...............................58-59
Hydraulic Hoses Assembly.......................................60-61
Hydraulic Fttings and Clamps Assembly..................62-63
Front Pointer Assembly.............................................64-65
Belt Drive Assembly.................................................66-69
Drive Pulley Assembly..............................................70-71
Bladeshaft Assembly................................................72-73
16", 20", 26" Bladeguard Assembly.........................74-75
30", 36" Bladeguard Assembly................................76-77
Optional Weight Kit Assembly...................................78-79
NOTICE
Specification and part number are subject to change
without notice.
Terms and Conditions of Sale — Parts.......................... 80
PAGE 4 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
www.multiquip.com
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Order via Internet (Dealers Only):
Best Deal!
Effective:
January 1st, 2006
If you have an MQ Account, to obtain a Username
and Password, E-mail us at: parts@multiquip.
com.
Order parts on-line using Multiquip’s SmartEquip website!
■ View Parts Diagrams
■ Order Parts
■ Print Specification Information
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Goto www.multiquip.com and click on
Order Parts to log in and save!
Note: Discounts Are Subject To Change
Order via Fax (Dealers Only):
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Fax your order in and qualify for a 2% Discount
on Standard orders for all orders which include
complete part numbers.*
Note: Discounts Are Subject To Change
Order via Phone: Domestic (US) Dealers Call:
1-800-427-1244
Non-Dealer Customers:
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
When ordering parts, please supply:
❒
❒
❒
❒
❒
❒
Dealer Account Number
Dealer Name and Address
Shipping Address (if different than billing address)
Return Fax Number
Applicable Model Number
Quantity, Part Number and Description of Each Part
❒ Specify Preferred Method of Shipment:
✓ UPS/Fed Ex
✓ DHL
■ Priority One
✓ Truck ■ Ground
■ Next Day
■ Second/Third Day
NOTICE
All orders are treated as Standard Orders and will
ship the same day if received prior to 3PM PST.
WE ACCEPT ALL MAJOR CREDIT CARDS!
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 5
explanation of code in remarks column
The following section explains the different symbols and
remarks used in the Parts section of this manual. Use the
help numbers found on the back page of the manual if there
are any questions.
NOTICE
The contents and part numbers listed in the parts
section are subject to change without notice. Multiquip
does not guarantee the availability of the parts listed.
Sample partS liSt
NO.
1
2%
2%
3
4
part NO. part Name
QtY. remarKS
12345
BOLT......................1 .....INCLUDES ITEMS W/%
WASHER, 1/4 IN............NOT SOLD SEPARATELY
12347
WASHER, 3/8 IN....1 .....MQ-45T ONLY
12348
HOSE ..................A/R ...MAKE LOCALLY
12349
BEARING ..............1 .....S/N 2345B AND ABOVE
NO. Column
QtY. Column
Numbers Used — Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other
parts that are sold in bulk and cut to length.
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
remarKS Column
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed
to describe the item can also be shown.
assembly/Kit — All items on the parts list with the
same unique symbol will be included when this item is
purchased.
Unique Symbols — All items with same unique
symbol
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
(@, #, +, %, or >) in the number column belong to the
same assembly or kit, which is indicated by a note in the
“Remarks” column.
Serial Number Break — Used to list an effective serial
number range where a particular part is used.
Duplicate item Numbers — Duplicate numbers indicate
multiple part numbers, which are in effect for the same
general item, such as different size saw blade guards in
use or a part that has been updated on newer versions
of the same machine.
NOTICE
When ordering a part that has more than one item
number listed, check the remarks column for help in
determining the proper part to order.
part NO. Column
Numbers Used — Part numbers can be indicated by a
number, a blank entry, or TBD.
TBD (To Be Determined) is generally used to show a
part that has not been assigned a formal part number
at the time of publication.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will
be clarified in the “Remarks” Column.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific model Number Use — Indicates that the part
is used only with the specific model number or model
number variant listed. It can also be used to show a
part is NOT used on a specific model or model number
variant.
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
“make/Obtain locally” — Indicates that the part can
be purchased at any hardware shop or made out of
available items. Examples include battery cables, shims,
and certain washers and nuts.
“Not Sold Separately” — Indicates that an item cannot
be purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available
for sale through Multiquip.
PAGE 6 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
SUGGESTED SPARE PARTS
SP7060 SAW
ENGINE PARTS FOR DEUTZ TURBO DIESEL ENGINE
1 TO 3 UNITS WITH DEUTZ TURBO DIESEL ENGINE
Qty. P/N
Description
1.........37094....................SWITCH, TOGGLE F-N-R
1.........37203....................SWITCH, ROLLER PLUNGER
2.........406000..................SWITCH, ROCKER
2.........37132....................FRONT WHEEL ASSEMBLY
2.........37095....................REAR WHEEL
1.........29509....................CAP, FUEL TANK
2.........560017..................GRIPS, HANDLEBAR
1.........H9406....................BULB, GE H9406
1.........15503....................KNOB, COMFORT
1.........37311....................BALL VALVE, WATER SYSTEM
2.........570005..................CLAMP, MUFFLER
2.........37048....................SPRING, WHEEL DRIVE
2.........582012..................BUSHING, QD
2.........915316..................SCREW, 5/8 - 11 X 3 LH GR8
2.........915315..................SCREW, 5/8 - 11 X 3 GR8
1.........574003..................ROPE, POINTER
1.........37212....................THROTTLE ASSEMBLY
2.........200019..................MUDFLAP, BLADEGUARD
2.........1174416................OIL FILTER, DEUTZ BF3L2012
2.........304010..................FUEL FILTER, DEUTZ BF3L2011
2.........P772579................PRIMARY AIR FILTER ELEMENT
2.........P775300................SAFETY AIR FILTER, DEUTZ BF3L2014
2.........21004-003.............FAN BELT, AX-35
2.........520007..................DRIVE BELT, 5G 3VX-530
1.........406017..................IGNITION SWITCH, W/KEY
2.........406017-1...............KEY, IGNITION
2.........306006..................FILTER, TRANSMISSION
...........
FOR SAWS WITH 16", 20", AND 26" BLADEGUARDS
2 ........37168....................FLANGE, INNER 5.0"
2.........37169....................FLANGE ASSEMBLY, OUTER 5.0"
2.........926790..................PIN, DOWEL
2.........362000..................HOSE, WATER #6LP (16" BLADEGUARD)
2.........362005..................HOSE, WATER #6LP (20" BLADEGUARD)
2.........362006..................HOSE, WATER #6LP (26" BLADEGUARD)
FOR SAWS WITH 30" AND 36" BLADEGUARDS
2 ........37177....................FLANGE, INNER 6.0"
2.........37176....................FLANGE ASSEMBLY, OUTER 6.0"
2.........926790..................PIN, DOWEL
2.........362007..................HOSE, WATER #6LP (30" BLADEGUARD)
2.........362008..................HOSE, WATER #6LP (36" BLADEGUARD)
NOTICE
Part numbers on this Suggested Spare Parts List may
supercede/replace the P/N's shown in the text pages of
this manual.
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 7
NAMEPLATES AND DECALS
4
1
MODEL
SERIAL NO.
5
6
25
7
9
P/N 37161
2
Engine exhaust and some of
its constituents, and some dust created
by power sanding, sawing, grinding,
drillingandotherconstructionactivities
contains chemicals known to the State
of California to cause cancer, birth
defects and other reproductive harm.
Some examples of these chemicals are:
8
Leadfromlead-basedpaints.
Crystallinesilicafrombricks.
Cementandothermasonryproducts.
Arsenicandchromium fromchemically
treatedlumber.
Your risk from these exposures varies,
depending on how often you do this type
of work. To reduce your exposure to
these chemicals: ALWAYS work in a
well ventilated area, and work with
approved safety equipment, such as
dust masks that are specially designed
to filter out microscopic particles.
3
WARNING
DIESEL FUEL can cause
fire or explosion.
Stop engine before fueling
Keep cigarettes, sparks
and flame away.
10
P/N 36092
WARNING
Inhaling exhaust fumes can result
in severe injury or death.
11
Only operate machine in wellventilated areas.
DO NOT inhale exhaust fumes.
DANGEROUS
FUMES
Only qualified personnel should
install, use, or service this equipment.
P/N 36090
12 PATENT PENDING
24
AT
ROT ION
17
13
23
CAUTION
When Larger Blade and Guard
is Installed, Belt Drive MUST
Be Changed to Proper Size.
See Owners Manual.
22
WARNING
14
TO PREVENT SERIOUS INJURY
DO NOT OPERATE SAW
WITHOUT PROPER TRAINING
& FULL UNDERSTANDING
OF THE OWNERS MANUAL
FAILURE TO COMPLY WITH THE C C AH
JADV EEE AV EEA OIEJGGVCBVVZ
WHEN OPERATING THIS MACHINE
S.M.I. MASONRY AND CONCRETE
SAW MANUFACTURER’S INSTITUTE
KEEP ALL
GUARDS IN
PLACE
ALWAYS WEAR SAFETY APPROVED
HEARING
PROTECTION
EYE OR FACE
PROTECTION
18
15
HEAD
PROTECTION
RESPIRATOR
SMI MASONRY AND CONCRETE
SAW MANUFACTURING INSTITUTE
21
AT
ROT ION
16
USE 15W- 40 ENGINE OIL
WARNING!
WARNING!
20
API SERVICE CI- 4 PLUS, CI- 4, CH- 4,
CG- 4, CF- 4, CF/SL/SJ
P/N 37540
19
KEEP FEET
CLEAR
KEEP HANDS
CLEAR
PAGE 8 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
NAMEPLATES AND DECALS
NO. PART NO.
1
37367
2
38232
3
38235
4
5
M600002
6
38213
7
37161
8
13118
9
20525
10
36092
11
36090
12
11912
13
25282
14
35137
15
36099
16
37540
17
21302
18
22122-001
19
25249-001
20
25250-001
21
25678
22
23330-001
23
606004
24
25491
25
38226
PART NAME
QTY.
REMARKS
DECAL, STAY LEVEL HANDLE WHITE
2
DECAL, MQ MULTIQUIP 5.93 X 7.45
2
DECAL, MQ SP7060
2
SERIAL TAG...............................................................1.................... CONTACT PARTS DEPT.
DECAL, DIESEL FUEL ONLY
1
DECAL, MQ LOGO 3.0 X 3.75
1
DECAL, HOT ISO HI-TEMPERATURE......................1.................... SAFETY ITEM
DECAL, POWDER COATED
1
DECAL, WARNING "PROP 65" 3.25 X 4.25..............1.................... SAFETY ITEM
DECAL, WARNING DIESEL FUEL 3.5 X 1.75...........1.................... SAFETY ITEM
DECAL, WARNING VENTILATION 2 X 4...................1.................... SAFETY ITEM
DECAL, PATENT PENDING
1
DECAL, ATTENTION BATTERY DISCONNECTED 1
DECAL, WARNING READ MANUAL ........................1.................... SAFETY ITEM
DECAL, PROTECTIVE CLOTHING ISO BLUE.........1.................... SAFETY ITEM
DECAL, HYDRAULIC RESERVOIR
1
DECAL, WARNING KEEP GUARDS IN PLACE........2.................... SAFETY ITEM
DECAL, WARNING RX-W.........................................2.................... SAFETY ITEM
DECAL, WARNING KEEP HANDS CLEAR...............2.................... SAFETY ITEM
DECAL, WARNING KEEP FEET CLEAR..................2.................... SAFETY ITEM
DECAL, BLADE ROTATION CCW.............................1.................... SAFETY ITEM
DECAL, CAUTION BELT DRIVE
2
DECAL, GUARD REMOVAL......................................2.................... SAFETY ITEM
DECAL, BLADE ROTATION CW
1
DECAL, CE
1
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 9
CONTROL PANEL DECALS
1
ENGINE
Air filter:
Oil:
Oil type:
Oil Service:
Fuel Filter:
HYDRAULIC SYSTEM
Replace outer element when the SYSTEMS
STATUS air filter restriction light comes on.
Replace inner element every fourth outer element.
Check oil level daily, do not overfill.
See Engine Manual.
Change oil and filter every 125 hours
of operation.
Change fuel filter every 250 hours of operation.
Oil type:
Oil Service:
Reservoir
Location:
LUBRICATION
MAINTENANCE INSTRUCTIONS
Check reservoir daily. Fill reservoir to
line marked FULL COLD.
15W-40 premium grade engine oil.
Change oil and filter every 500 hours of
operation or annually, whichever occurs first.
Reservoir is located inside console. Remove
rear panel for access.
Oil Level:
Grease every 125 hrs. of operation.
Use premium grade waterproof
EP (extreme pressure) grease.
Locations: Front axle pivot bearings (2), lift
cylinder pins (2), engine tilt cylinder
pin (1).
2
LIGHTS
ON
AUXILIARY
ON
THROTTLE
BLADESHAFT
DIS-ENGAGE
DRIVE BELTS
Service:
Type:
Note:
Wheel drive propulsion system, lift pump,
and oil bath bladeshaft share common
hydraulic oil reservoir, thus are maintained
as a single system.
Belt Tension: Bladeshaft drive belt tension is applied hydraulically when
bladeshaft drive is engaged.
Perform following procedure with saw fully lowered.
Loosen jam nut on belt tension limiting bolt. Turn belt tension limiting bolt
counterclockwise to create ½” minimum distance between end of bolt and frame.
Start engine and engage belt drive; increase engine speed to full throttle position for
15 seconds minimum. Slow engine speed to idle and shut engine off. Turn belt
tension limiting bolt clockwise until bolt lightly contacts frame. Tighten locknut.
To Adjust
Drive Belt
Tension:
BLADE SPEED
IGNITION SWITCH
TACHOMETER
ENGINE PRE-HEAT
GLOW PLUG
ENGINE WILL NOT CRANK
OR START WHEN E-STOP
BUTTON IS DEPRESSED
START
ON
TO INCREASE ENGINE SPEED: TURN KNOB COUNTERCLOCKWISE.
TURN KNOB CLOCKWISE.
TO REDUCE ENGINE SPEED:
FOR QUICK THROTTLE ACTION: DEPRESS RED BUTTON AND
PUSH OR PULL KNOB.
OFF
3
OFF
6
5
150
4
7
SYSTEMS STATUS
WATER PUMP
OPERATING INSTRUCTIONS
BLADESHAFT ROTATION DIS-ENGAGEMENT SYSTEM
175
125
100
Step 1:
Raise saw above desired cutting depth.
Step 2:
Turn depth control knob counterclockwise
until saw cannot be lowered by pushing raise/lower
switch forward.
Step 3:
Hold raise/lower switch in the lowering
position and rotate the depth control knob clockwise
until desired cutting depth is achieved. The saw will
repeat to the same depth until re-adjusted.
OFF
INDICATOR
DEPTH
DEPTH STOP CONTROL
To Control Depth of Cut with Saw
Running and Blade Mounted:
ENGINE
PRE-HEAT
ENGAGE
8
Engine must be at idle when engaging or
dis-engaging bladeshaft drive.
200
FORWARD
9
230
3
255
10
75
280
11
2
50
To stop bladeshaft rotation:
Push rocker switch labeled BLADESHAFT forward.
Engine will tilt forward, dis-engaging the belt drive.
WARNING
12
To Re-adjust for Full Cutting Depth:
330
1
25
380
0
MM
14
ENGINE MUST BE SHUT OFF
when removing or installing
blade or bladeguard or performing any type of service
to bladeshaft or any other component on machine!
15
INCH
WATER
SUPPLY:
Connect water supply to water inlet. Move
water ON/OFF CONTROL to ON position.
Adjust WATER FLOW CONTROL lever to
desired position. Drain watering system in
cold weather to prevent damage due to
freezing.
BLADES:
Always follow blade manufacturer's
recommendations for blade selection,
speed and application.
NEVER exceed blade manufacturer's
maximum rated RPM. See operator's manual
for detailed blade mounting instructions.
STARTING
ENGINE:
Set CONTROL HANDLE to NEUTRAL position.
Set THROTTLE to IDLE. Turn start switch to
ON position. Wait for glow plug indicator light
to go out. Momentarily turn switch to start
position; release switch as soon as engine
starts. Allow engine to warm up for several
minutes before increasing engine speed. Use
approved diesel fuel only.
STOPPING
ENGINE:
Do not stop engine abruptly when hot! Reduce
THROTTLE to IDLE and allow engine to run 1
to 2 minutes before turning ignition switch off.
Damage to engine may occur if not allowed to
cool adequately.
FWDNEUTRALREV
CONTROL:
The panel mounted handle controls
FORWARD, NEUTRAL and REVERSE
operation. Neutral position stops or holds saw
in a stationary position. Incremental
movement in the FORWARD or REVERSE
direction will increase speed proportionate
to amount of movement.
13
355
0
Check all fluid levels. Secure blade firmly to
bladeshaft. Make sure all protective guards
are in place and properly mounted. Wear eye,
ear protection and protective clothing.
To start bladeshaft rotation:
Push rocker switch labeled BLADESHAFT backward.
Engine will tilt back, engaging belt drive.
305
Hold raise/lower switch in the lowering position and
rotate the depth control knob clockwise until saw is
fully lowered. Rotate depth control knob clockwise
additional 1 turn.
BEFORE
STARTING:
NEVER
attempt to remove or install blade or bladeguard
with engine running by dis-engaging the belt drive!
NEUTRAL
NEVER
attempt to service any component with the
engine running!
NEVER
leave saw unattended while engine is running!
TO ADJUST CUT DEPTH INDICATOR:
LOWER SAW UNTIL BLADE CONTACTS
SURFACE, ADJUST DIAL TO ZERO.
WATER
FLOW
CONTROL
RAISE/LOWER
SWITCH
ADJUST WATER FLOW VALVE
FOR DESIRED WATER FLOW
NEVER EXCEED BLADE MANUFACTURER'S RECOMMENDED RPM'S
REVERSE
RAISELOWER
FUNCTION:
RAISE-LOWER function is controlled by the
switch mounted at the right side of the
CONTROL HANDLE. Push toggle switch
lever forward to lower saw. Pull toggle switch
lever backward to raise saw.
BRAKES:
This saw is equipped with parking brakes.
Brakes are applied automatically when engine
is off and dis-engaged when engine is running.
FWD-NEUTRAL-REV
CONTROL
PAGE 10 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
ON
OFF
ON
WATER
OFF
CONTROL PANEL DECALS
NO.
1
2
3
PART NO.
37361
37354
37353
PART NAME
DECAL, MAINTENANCE, 7000 SERIES
DECAL, INSTRUMENT PANEL, 7000 SERIES
DECAL, OPERATION CONSOLE PANEL
QTY.
1
1
1
REMARKS
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 11
ELECTRICAL CONTROL ASSY.
PAGE 12 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
ELECTRICAL CONTROL ASSY.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18*
19
PART NO.
PART NAME
QTY.
REMARKS
406000
SWITCH, ROCKER CH# M-58031-01
2
4060 17
IGNITION SWITCH, with keys..............................1.................... includes items w/*
37198
EMERGENCY STOP SWITCH..................................1.................... SAFETY ITEM
37094
SWITCH, TOGGLE SPDT MOMENTARY ON-ON 1
37203
SWITCH, SNAP ACTION ROLLER PLUNGER
1
37490
HARNESS, RELAYS AND CIRCUIT BREAKERS 1
406021
INDICATOR, ENGINE
1
37243
SWITCH, ROLLER ARM
1
933240
WASHER, FLAT SAE 1/4 GRD 9 YZ
3
405000
CONNECTOR, 4-WAY SOCKET
1
37368
TACHOMETER, ELECTRIC 0-3000 RPM
1
8381
BOOT, TOGGLE SWITCH
1
406020
BLANK, ROCKER SWITCH
2
973752
SCREW, BHHC 1/4 - 20 X 5/8 SS
3
37325
SCREW, SHC M5 - 0.8 X 30MM
2
37324
NUT, NYLOC M5 - 0.8
2
28922-058
WASHER, M5
2
406017-1
KEY, IGNITION
1
25628solenoid, lift pump
1
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 13
CONSOLE MOUNTS ASSY.
PAGE 14 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
CONSOLE MOUNTS ASSY.
NO. PART NO.
PART NAME
QTY.
1
20742
ISOLATOR, RB2 RING/BUSHING
4
2
20743
WASHER, ISO SNUB KROFUND DYN 148099-18 4
3
575001
RUBBER ISOLATOR, TPC# 60166-1
4
4
37231-353
MOUNT, ISOLATOR FRONT
2
5
37233-353
MOUNT, ISOLATOR SIDE
2
6
37227-353
MOUNT, CONSOLE ISOLATOR FRONT
2
7
12832
WASHER, SNUBBING
4
8
06503-026
SCREW, HHC 1/2 - 13 X 3-1/4
4
9
1665
SCREW, HHC 3/8 - 16 X 2
4
10
37116-353
CONSOLE W/A
1
11
933242washer, flat sae 3/9 grd 9 y
8
12
0205screw, hhc 3/8-16 x 1
8
13tbdscrew
4
14tbdwasher
4
REMARKS
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 15
REAR CONSOLE ACCESS PANEL ASSY.
5
8
6
1
2
4
7
3
9
PAGE 16 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
REAR CONSOLE ACCESS PANEL ASSY.
NO.
1*
2*
3*
4*
5
6
7*
8*
9
PART NO.
10024
10930
12287
29057
37219
37220
37254-353
560020
37253
PART NAME
QTY.
REMARKS
NUT, NYLOC 1/4 X 20
4
WASHER, FENDER 1/4 X 1-1/4
4
SCREW, THP 1/4 - 20 X 3/4 SS
4
DOCUMENT BOX
1
STRIP, BACKING PLATE SAW CONSOLE
1
STRIP, VERTICAL SAW CONSOLE
2
PANEL, REAR SAW ACCESS
1
LATCH, REAR SAW ACCESS PANEL
2
PANEL ASSEMBLY, REAR SAW ACCESS................1.................... includes items w/*
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 17
LIGHT CONNECTOR/DASH ACCESS ASSY.
PAGE 18 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
LIGHT CONNECTOR/DASH ACCESS ASSY.
NO.
1
2*
3*
4*
5
6
7
8
9
10*
11+#
12+#
13+#
14+
15+
16+
17+
18+
19+#
20
21#
PART NO.
0655
12171
12176
12179
13287
25865
37234-353
923114
933241
405000
0161 C
0161 d
0300 A
2532
15503
120206
405001
405002
H9406
M18004
11963
PART NAME
QTY.
REMARKS
SCREW, HHC 5/16 - 18 X 3/4
8
SEAL, WEATHERPACK 16-18 GA,GREEN
2
CONNECTOR, WEATHERPACK 2 PIN MALE
1
TERMINAL, WEATHERPACK MALE 14-16 GA
2
NUT, NYLOC 8-32
2
HARNESS, LIGHT KIT...............................................1.................... includes items w/*
COVER w/A, CONSOLE DASH ACCESS
1
SCREW, SHC 8-32 X 1/2
2
WASHER, FLAT SAE 5/16 GRD 9YZ
8
CONNECTOR, 4-WAY SOCKET CHROME
1
WASHER, LOCK 5/16 MED
2
NUT, HEX 5/16 - 18
2
SCREW, HHC 5/16 - 18 X 2
1
LIGHT ASSEMBLY.....................................................1.................... includes items w/#
KNOB, COMFORT GRIP STAR
1
LIGHT BAR
1
CONNECTOR PLUG, 4-PIN FEMALE
1
CORD, LIGHT EXTENDABLE
1
BULB, GE H9406
1
LIGHT KIT, SAW........................................................1.................... includes items w/+
BOLT, CARRIAGE 5/16 - 18 X 1
1
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 19
BELT AND ENGINE GUARDS ASSY.
PAGE 20 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
BELT AND ENGINE GUARDS ASSY.
NO.
1
3
4
5
8
9
PART NO.
PART NAME
QTY.
REMARKS
0166
SCREW, HHC 3/8 - 16 X 7/8
5
15503knob, comfort
1
37202-353guard, belt drive................................................1.................... SAFETY ITEM
37209-353guard, engine.......................................................1.................... SAFETY ITEM
584011wrench, 15/16 blade closed end
1
933242
WASHER, FLAT SAE 3/8 GRD 9 YZ
5
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 21
DEPTH INDICATOR/STOP SWITCH ASSY. (old style)
PAGE 22 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
DEPTH INDICATOR/STOP SWITCH ASSY. (old style)
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
PART NO.
PART NAME
10024
NUT, NYLOC 1/4 - 20
37155
PULLEY, CABLE .75 OD
37235
BASE, SAW DEPTH INDICATOR
37240
PULLEY, CABLE .75 OD
37241
SHAFT, DEPTH INDICATOR
37332
RING, 3/16 E-STYLE EXTERNAL
37401
SCREW, SH SHLDR 1/2-20, 5/16 OD X 1/4 L
37504cable, nylon coat ss .049
110031
POINTER, CONCRETE SAW DEPTH
460019
FLANGE, BEARING 0.25 ID X 0.75 OD
560025
KNOB, SAW DEPTH INDICATOR
565005
SPRING, EXTENSION 583059
SHIM, 0.375 OD X 0.25 ID X .020 THK
584025
STUD, 1/4 - 20 X 1-3/4 NO PLT
933240
WASHER, FLAT SAE 1/4 GRD 9 YZ
973752
SCREW, BHSC 1/4 - 20 X 5/8 SS
37248mount, switch pivot plate
37246nut, swivel depth stop
37247
KNOB, DEPTH STOP CONTROL
37249
COLLAR, SHAFT THREADED 3/8 - 16
37250
WASHER, BELLEVIEW .317 X .625
19470
WASHER, FLAT 5/16 USS
933242
WASHER, FLAT SAE 3/8 GRD 9 YZ
5283
NUT, NYLOC 5/16 - 18
10133
NUT, NYLOC 3/8 - 16
37251
WASHER, BELLEVIEW .389 X .750
37375
STUD, 3/8 - 16 X 4
4001
WASHER, FLAT USS 3/8 PLD
QTY.
2
1
1
2
1
2
1
1
1
1
1
1
5
1
1
2
1
1
1
1
2
2
1
2
1
2
1
3
REMARKS
NOTICE
Parts on this page are no longer available. See Depth
Indicator/Stop Switch Assy. (New Style).
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 23
DEPTH INDICATOR/STOP SWITCH ASSY. (new style)
6
10
5
19
2
13
1
9
14
19
2
3
10
10
10
8
4
4
12
16
9
20
17
11
7
15
18
17
PAGE 24 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
DEPTH INDICATOR/STOP SWITCH ASSY. (new style)
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PART NO.
PART NAME
QTY.
37544
SHAFT, DEPTH INDICATOR
1
37545
BUSHING, FLANGED
2
37547
SHAFT, IDLER PULLEY
2
37548
PULLEY, IDLER
2
110031
POINTER, CONCRETE SAW DEPTH
1
560025
KNOB, SAW DEPTH INDICATOR
1
37549
PULLEY, DUAL GROOVE
1
37550
BELT, INDICATOR DRIVE
1
0948
WASHER, FLAT SAE 1/4 3
37332
RING, 3/16 E-STYLE EXTERNAL
6
926149
SCREW, SHDLR 1/4D X 5/16L, 10-24 SCKT HD 1
37162
SPRING, EXTENSION 1
973752
SCREW, BHSC 1/4 - 20 X 5/8 SS
2
37551
HOUSING, DEPTH INDICATOR
1
37557
BRACKET, CABLE INDICATOR
1
2295
SCREW, HHC 1/4 - 20 X 7/8
1
10024
NUT, NYLOC 1/4 - 20
2
37401
SCREW, SH SHLDR 1/2-20, 5/16 OD X 1/4 L
1
37679
RING, SNAP SH 87
2
37678cable ASSY., DEPTH INDICATOR
1
REMARKS
NOTICE
Parts on this page replace those listed on Depth Indicator/Stop Switch Assy. (Old Style)
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 25
F-N-R ASSY.
PAGE 26 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
F-N-R ASSY.
NO.
1*
2*
3*
4*
5*
6*
7*
8*
9*
10*
11*
12*
13*
14*
15
16
17
18
19
20
21
22
23
24
PART NO.
PART NAME
QTY.
REMARKS
576003sNAP RING - HO-185
1
460021
BEARING, ROLLER # 6204 2RS
2
20842
SCREW, PAN HD 6-32 X 1/4
4
579072
GROMMET, 1/2" ID
1
926917
PIN, DOWEL 1/4 X 1/2
2
37015
SPACER, FNR PIVOT
1
37014
DISC, FNR FRICTION BRAKE
1
37013
PLATE, FNR ACCESS COVER
1
37022
WELDMENT, FNR HANDLE
1
37016
PLATE, FNR BRAKE
1
37091
SPRING, SMALLEY WAVO RW-0250
1
37024
WELDMENT, FNR SPRING PLATE
1
37025
NUT, HEX FINISH M20-2.5
2
37026
SCREW, HHC M20 X 2.5 X 120
1
37021
FNR ASSEMBLY........................................................1.................... INCLUDES ITEMS W/*
2153
ROD END
2
37136
CABLE, PUSH PULL 56"
1
37299
STANDOFF, PUMP CONTROL
1
07469-004
SCREW, SHC 10-32 X 1/2
1
4683
SCREW, HHC 5/16 - 18 X 5/8
1
933241
WASHER, FLAT SAE 5/16 GRD 9 YZ
1
2203
WASHER, FLAT #10
1
10019
NUT, NYLOC 10-32
1
3513
SCREW, HHC 10 - 32 X 1
1
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 27
FUEL ASSY.
12
2
3
13
6
2
14
15
4
10
12
5
9
8
7
1
11
8
PAGE 28 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
FUEL ASSY.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
PART NO.
19473
19633
29509
35022
37128
37191
37498
37500
37501
37502
37809
368006
37195-353
933242
0205
PART NAME
CLAMP, HOSE WORM # 2
BUSHING, RUBBER FUEL DAPCO 10672
CAP, FUEL TANK 2.25 DIA, ONE WAY VALVE
CLAMP, LOOP CUSHIONED #8
BALL VALVE, 90 W/SCREEN #6,DAPCO 12862
FUEL TANK
FUEL LINE 30R7 5/16 X 12
FUEL LINE 30R7 5/16 X 40.00
FUEL LINE 30R7 1/4” X 64”
TUBING, VINYL 1/4 CLEAR
FILTER, DEUTZ 1178753, IN-LINE
FITTING, FUEL 90 DEG. #4 X #6 BARB
MOUNT, FUEL TANK
WASHER, FLAT SAE 3/8 GRD 9 YZ
SCREW, HHC 3/8 - 16 X 1.0
QTY.
6
4
1
1
1
1
12”
40”
64”
1
1
3
1
5
5
REMARKS
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 29
BATTERY ASSY.
PAGE 30 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
BATTERY ASSY.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
PART NO.
PART NAME
QTY.
0166
SCREW, HHC 3/8 - 16 X 7/8
1
0655
SCREW, HHC 5/16 - 18 X 3/4
4
37088box, battery
1
37098retainer, battery hold-down
1
37258-353clip, battery retainer
1
37284
SCREW, HHC m14 - 2.0 x 20mm grd 8.8 pltd 1
37326cable, positive battery starter
1
37327cable, positive batt. solenoid lift pump 1
37328cable, negative battery engine
1
37329cable, negative battery lift pump
1
37355cable, positive batt. solenoid lift pump 1
404006battery, exide orb75dt-84
1
915101
SCREW, HHC 3/8 - 16 X 1/2 grd 8
2
933241washer, flat sae 5/16 grd 9 yz
4
933245washer, flat sae 9/16 grd 9 yz
1
REMARKS
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 31
STAY-LEVEL HANDLEBARS ASSY.
23
6
14
9
11
4
1
22
21
19
10
14
12
2
1
5
13
3
16
22
11
9
17
15
20
18
10
12
21
19
7
13
5
9
8
11
PAGE 32 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
STAY-LEVEL HANDLEBARS ASSY.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15#
16#
17#
18#
19
20#
21
22
23*
PART NO.
PART NAME
QTY.
REMARKS
37085bearing, 1.25" tap base
1
37239shaft, crossdrive slh
1
37119receiver, slh handlebar lh
1
37120receiver, slh handlebar rh
1
37125bearing, plain 1.0625 ultrasert uc200
2
560023handlebar assy., concrete saw...................2.................... includes items w/*
37174link assy., slh control coupler .................1.................... includes items w/#
37139slh control lever
1
16523screw, hhc 3/4 - 10 x 1-1/2 gd 8
3
933245washer, flat sae 9/16 grd 9 yz
4
933247washer, flat sae 3/4 grd 9 yz
3
37284screw, hhc m14-2.0 x 20mm grd 8.8 pltd 4
37312ring, retaining whm-106
2
19977knob, clamp 1/2 - 13 thread
2
37123link, slh control coupler lower
1
37173link, slh control coupler upper
1
37297plate, slh clamp
1
16526screw, hhc 1/2 - 13 x 1-3/4 grd 8
2
4196
SCREW, HHC 3/8 - 16 X .75
2
933244
WASHER, FLAT SAE 1/2 GRD 9 YZ
2
4001
WASHER, FLAT USS 3/8 PLD
2
37133
PIN, SLH COUPLER PIVOT
2
560017
GRIP, HANDLEBAR
2
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 33
HANDLEBAR BOOT ASSY.
1
4
3
2
PAGE 34 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
HANDLEBAR BOOT ASSY.
NO.
1
2*
3*
4*
PART NO.
37117
37105
37061
5065 b
PART NAME
QTY.
REMARKS
BOOT ASSY., HANDLEBAR......................................1.................... INCLUDES ITEMS W/*
BOOT, SLH HANDLEBAR
1
PLATE, RETAINER
1
SCREW, php 10 - 32 X 1/2
6
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 35
WATER SYSTEM ASSY.
2
3
5
2
1
7
3
4
6
PAGE 36 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
WATER SYSTEM ASSY.
NO.
1
2
3
4
5
6
7
PART NO.
PART NAME
QTY.
38313
FITTING, BRASS (f) 3/4 GHT SWIVEL 3/8 MNPT 1
37813
FITTING, 90 1/2MP - 3/8FP
2
37311
BALL VALVE, BRASS 3/8 MNPT X FNPT
2
37533
HOSE ASSEMBLY, WATER SYSTEM 76.5"
1
37397fitting, 8MJ X 1/2 MP
1
37532fitting, qc female
1
37296
HOSE ASSEMBLY, CROSSOVER
1
REMARKS
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 37
engine ASSY.
PAGE 38 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
engine ASSY.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
PART NO.
PART NAME
QTY.
REMARKS
35396
ENGINE, DEUTZ 60HP BF3L2011 TRBO DSL
1
2299
SCREW, HHC M8 - 1.25 X 16MM
2
933241
WASHER, FLAT SAE 5/16 GRD 9 YZ
2
10024
NUT, NYLOC 1/4 X 20
2
933240
WASHER, FLAT SAE 1/4 GR 9 YZ
2
915004
SCREW, HHC 1/4 - 20 X 7/8
2
37473
HEAT SHIELD............................................................1.................... SAFETY ITEM
37255
THROTTLE LEVER
1
1174696
FILTER, FUEL DEUTZ...............................................1.................... replaces 304010
1174416
FILTER, OIL DEUTZ..................................................1.................... replaces 306012
21004-003v-bELT, AX-35
1
37256bracket, throttle/fnr cable
1
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 39
throttle control assy.
1
7
2
8
3
4
9
5
6
PAGE 40 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
throttle control assy.
NO.
1
2
3
4
5
6
7
8
9
PART NO.
PART NAME
37212
THROTTLE 37256
BRACKET, THROTTLE/FNR CABLE
37255
LEVER, THROTTLE
933240
WASHER, FLAT SAE 1/4 GRD 9 YZ
25624
SWIVEL, CABLE END W/ WASHER
923113
SCREW, SHC 8 - 32 X 3/8 GRD 8
23942-097
WASHER, M6
12464
SCREW, HHC M6 - 1.0 X 16MM
25634bulk head adaptor
QTY.
1
1
1
1
1
1
2
2
1
REMARKS
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 41
engine mounts assy.
2
7
14
15
10
4
3
10
7
15
7
14
6
10
1
6
4
9
14
3
12
11
5
10
8
14
12
13
15
PAGE 42 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
15
engine mounts assy.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
PART NO.
PART NAME
37491mount, rh engine
37100mount, lh engine
37099pin, engine pivot
37031bushing, spherical-ultrasert uc200
37147pin, upper engine pivot
37313ring, spiral retaining whm-200
37310screw, hhc m14-2.0 x 40mm grd 10.9 np
37146screw, hhc m14-2.0 x 35mm grd 10.9 np
913838screw, hhc 3/4 - 10 x 4 grd5 zinc
933245
WASHER, FLAT SAE 9/16 GRD 9 YZ
4389nut, hex 3/4 - 10
16530screw, hhc 7/16 - 14 x 1
933243
WASHER, FLAT SAE 7/16 GRD 9 YZ
37037washer, engine pivot pin
21376screw, hhc 5/8 - 11 x 1-1/2
QTY.
1
1
2
2
1
2
6
2
1
8
1
2
2
4
4
REMARKS
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 43
air cleaner assy.
PAGE 44 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
air cleaner assy.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
PART NO.
PART NAME
37151
HOSE ASSY, AIR INTAKE
10434
CLAMP, HOSE WORM # 32 1-9/16 TO 2"
35309
TUBE, AIR INTAKE BREATHER
15538
CLAMP, HOSE WORM # 6
406018
INDICATOR, ELECTRICAL SERVICE 65516
FITTING, NIPPLE 1/8" MP
29218
CLAMP, HOSE WORM # 48
933241
WASHER, FLAT SAE 5/16 GRD 9 YZ
1665
SCREW, HHC 3/8 - 16 X 2
10133
NUT, NYLOC 3/8 - 16
M940653
SCREW, HHC M6 - 1.0 X 25MM GRD 10.9
1928
SCREW, HHC M8 - 1.25 X 40MM
9182
SCREW, HHC M8 - 1.25 X 45MM
2866
SCREW, HHC M8 - 1.25 X 20MM
35399
GASKET, AIR INTAKE TUBE
37153
HOSE, 3.00 ID MOLDED 90 DEGREE
37199
AIR CLEANER ASSEMBLY 3 INCH #7VLR
37307
SPACER, AIR CLEANER MOUNT .375L
37309
SPACER, AIR CLEANER MOUNT .875L
962019
CLAMP, HOSE WORM # 44
37317
BUSHING, AIR INTAKE 2.75 X 3.00
37112
MOUNT, AIR FILTER
37761
BRACKET, AIR INTAKE BODY
P772579
PRIMARY FILTER, DEUTZ BF3L2013
P775300
SAFETY FILTER, DEUTZ BF3L2014
12832washer, snubbing
575001rubber isolator, tpc #60166-1
QTY.
1
1
1
1
1
1
2
3
4
4
2
1
1
1
1
1
1
1
1
2
1
1
2
1
1
4
4
REMARKS
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 45
muffler assy.
PAGE 46 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
muffler assy.
NO.
1*
2*#
3*#
4*#
5*#
6*#%
7*#%
8*#$
9*#$
10*#$
11*#$
12
13*
14*#
PART NO.
285003
570005
8131
933241
280005
940693
940358
25592
25591
25642
25593
37143
280002
280004
PART NAME
QTY.
REMARKS
EXHAUST, 12" EXTENSION
1
CLAMP, MUFFLER 2-1/2" 5/16 u-BOLT
2
NUT, FINISH L.H. 5/16 - 24
4
WASHER, FLAT SAE 5/16 GRD 9 YZ
4
MUFFLER .................................................................1.................... includes items w/%
SCREW, HHC M10 - 1.5 X 25MM GRD 10.9 NP 2
WASHER, M10 X 21MM ZINC
2
NUT, M8 - 1.25"
3
WASHER, M8
3
GASKET, TURBO INLET DEUTZ
1
STUD, M8 - 1.25 X 30MM
3
MUFFLER ASSEMBLY COMPLETE.........................1.................... includes items w/*
MUFFLER AND FLEX KIT ASSEMBLY.....................1.................... includes items w/#
FLEX KIT ASSEMBLY................................................1.................... includes items w/$
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 47
lift bail assy.
PAGE 48 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
lift bail assy.
NO.
1
2
3
4
5
6
7
8
9
10
PART NO.
37114
37115
940694
37314
37315
940358
933244
933241
16083
06500-007
PART NAME
QTY.
REMARKS
SPACER, DEUTZ ENGINE LIFTING BRACKET 1
BRACKET, DEUTZ ENGINE LIFTING.......................1.................... SEE NOTE below
SCREW, HHC M10 - 1.5 X 30MM FT 10.9 NP
1
SCREW, HHC M12 - 1.75 X 120MM TAP BOLT
1
SCREW, HHC M12 - 1.75 X 120MM 10.9 NP
1
WASHER, M10 X 21MM ZINC
1
WASHER, FLAT SAE 1/2 GRD 9 YZ
3
WASHER, FLAT SAE 5/16 GRD 9 YZ
1
NUT, HEX M12 - 1.75 NO PLATE
1
SCREW, HHC 5/16 - 18 X 7/8
1
NOTICE
Type 2 Rope Guide System supercedes Type 1 Rope
Guide System. See Front Pointer Assy.
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 49
platform guards/rear pointer assy.
16
11
3
15
4
5
4
5
1
2
9
10
9
6
10
7
12
8
13
10
14
PAGE 50 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
platform guards/rear pointer assy.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PART NO.
PART NAME
QTY.
REMARKS
37185
GUARD, BLADESHAFT PULLEY..............................1.................... safety item
583091
STRAP, LOWER BELT GUARD
1
583092
WASHER, LOWER BELT PROTECTOR
1
933244
WASHER, FLAT SAE 1/2 GRD 9 YZ
4
3214
SCREW, HHC 1/2 - 13 X 1-1/4
4
915105
SCREW, HHC 3/8 - 16 X 1.0 GRD 8
1
110020
POINTER, REAR SAW
1
37360
SHIELD, CONCRETE SLURRY
1
915105
SCREW, HHC 3/8 - 16 X 1.0 GRD 8
3
933242
WASHER, FLAT SAE 3/8 GRD 9 YZ
6
37122platform, w/a
1
37450strip, slurry control
1
10133nut, nyloc 3/8 - 16
3
20982screw, fhsc 3/8 - 16 x 1-1/2 plated
3
M200000
GUARD, SAW BLADE COLLAR
1
35030guard w/a, saw blade collar, rh
1
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 51
wheel drive assy.
PAGE 52 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
wheel drive assy.
NO. PART NO.
PART NAME
1
37102
MOUNT, WHEEL MOTOR
2
37095
WHEEL, 12 X 3 TAPERED BORE
3
37096
BRAKE PAD
4
37097
BRAKE ARM
5
37138
CAP, WHEEL DUST
6
0655
SCREW, HHC 5/16 - 18 X 3/4
7
0205
SCREW, HHC 3/8 - 16 X 1.0
8
3214
SCREW, HHC 1/2 - 13 X 1-1/4
9
933213
WASHER, FENDER 5/16 X 1 ZINC 10
37048
SPRING, 1.125 X .187 X 4 W/EYELET
11
23858-001
EYEBOLT, 3/8 - 16 X 2.0
12
933242
WASHER, FLAT SAE 3/8 GRD 9 YZ
13
933244
WASHER, FLAT SAE 1/2 GRD 9 YZ
14
933247
WASHER, FLAT SAE 3/4 GRD 9 YZ
15
10133
NUT, NYLOC 3/8 - 16
16
968011
NUT, HEX FINISH 1/2 - 13
17
19974
PIN, CLEVIS 1/2 X 1.25 18
966166
PIN, CLEVIS 3/4 X 2
19
965105
PIN, COTTER 5/32 X 1-1/2
20
965103
PIN, COTTER 5/32 X 1
21
37322
SPRING, CREST TO CREST 22
1456
NUT, HEX FINISH 3/8 - 16
24
37923nut, slotted 3/4-20 hex
26
0126
KEY, woodruff #606 3/16 x 3/4
QTY.
1
2
2
1
2
2
8
5
2
2
2
10
7
3
2
2
3
1
1
3
4
2
2
2
REMARKS
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 53
front axle assy.
PAGE 54 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
front axle assy.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17*
18*
19*
20*
21
PART NO.
37106
933246
06505-008
37132
2621
26091
2186
926064
5283
1162 a
37040
933244
16629
37260
915211
37138
37131
460002
485002
576003
37165
PART NAME
QTY.
REMARKS
FRONT AXLE W/A
1
WASHER, FLAT 5/8 SAE GRD9 YZ
2
SCREW, HHC 5/8 - 11 X 1.00
2
WHEEL ASSEMBLY, FRONT......................................2................... INCLUDES ITEMS W/*
FITTING, GREASE ZERK STR 1/4 - 28
2
SCREW, SHS 1/4 - 28 X 1/4 CUP POINT
4
SCREW, SHC 5/16 - 18 X 2-1/4 PLTD
1
SCREW, SQHS CUP POINT 5/16 - 24 X 5/8
1
NUT, NYLOC 5/16 - 18
1
CAP, GREASE ZERK #2 YELLOW
2
BEARING, 1.250" FLANGE
2
WASHER, FLAT SAE 1/2 - 13 GD 8
16
NUT, NYLOC 12 - 13 GD 8
12
PIN, LIFT CYLINDER
1
SCREW, HHC 1/2 - 13 X 2 GRD8 YZ
12
CAP, WHEEL DUST
2
WHEEL, 8 X 3 POLYURETHANE
2
BEARING, BALL KOYO # 6005 SRS
4
SEAL, OIL CR # 28655
2
SNAP RING, - HO-185
2
PLATE, BACKING
2
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 55
hydraulic system assy.
PAGE 56 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
hydraulic system assy.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
PART NO.
PART NAME
QTY.
37113pump, 24v DC LIFT - HYDROGEAR
1
306006
FILTER, TRANSAXLE
1
25617
FILTER HEAD, TRANSAXLE
1
37121
LIFT CYLINDER ASSEMBLY
1
37211
CYLINDER, BRAKE 2" X 1.5" STROKE
1
37213
RESERVOIR, 350ML HYDROGEAR 71327
1
37104
PUMP, HYDROGEAR
1
37056
MOTOR, WHEEL - HYDROGEAR HGM-15P-7131 2
37162
EXTENSION SPRING, 1.8" - 8.1 LB RATE
1
933240
WASHER, FLAT SAE 1/4 GRD 9 YZ
4
1579
SCREW, HHC 1/4 - 20 X .5
2
4514
SCREW, HHC 1/4 - 20 X 5/8 GRD 5
2
REMARKS
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 57
engine pivot cylinder assy.
PAGE 58 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
engine pivot cylinder assy.
NO. PART NO.
PART NAME
QTY.
REMARKS
1*
37445
VALVE, CHECK
2
2*
37446
VALVE, CARTRIDGE 4-WAY 2-POSITION
1
3*
37447
SOLENOID COIL 12VDC
1
4*
37448
PISTON, PILOT
1
5*
37449
PISTON, BACKUP RING....................................... 2.................s/n zd3700241 and below
6*
37492
O-RING.................................................................. 1.................s/n zd3700241 and below
7*
37390
CYLINDER, HYDRAULIC
1
8
37495
CYLINDER AND VALVE ASSEMBLY..................... 1.................includes items w/*
9
37260pin, lift cylinder
1
10
37166pin, lower engine pivot
1
11
933243washer, flat sae 7/16 grd 9 yz
2
12
16530screw, hhc 7/16 - 14 x 1
2
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 59
hydraulic hoses assy.
PAGE 60 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
hydraulic hoses assy.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PART NO.
37475
37476
37477
37290
37295
37294
37347
37291
37292
37278
37279
37283
37281
37282
37293
37280
PART NAME
QTY.
REMARKS
HOSE ASSEMBLY, #4 LP
1
HOSE ASSEMBLY, #4 LP
1
HOSE ASSEMBLY, #4 LP
1
HOSE ASSEMBLY, #4 HP PARFLEX
1
HOSE ASSEMBLY, #6-8 LP
1
HOSE ASSEMBLY, #6 LP
1
HOSE ASSEMBLY, #6 LP......................................... 1..................... SEE NOTE below
HOSE ASSEMBLY, #4 PARFLEX
1
HOSE ASSEMBLY, #4 LP
1
HOSE ASSEMBLY, #6 PARFLEX
1
HOSE ASSEMBLY, #6 PARFLEX
1
HOSE ASSEMBLY, #8 LP
1
HOSE ASSEMBLY, #6 LP
1
HOSE ASSEMBLY, #6 LP
1
HOSE ASSEMBLY, #4 LP
1
HOSE ASSEMBLY, DRIVE MOTOR CROSSOVER 1
NOTICE
FOR SAWS up to S/N ZD3700238 ONLY. When Ordering
this hose (P/N 37347 item 7 on this page), also order two
(2) each fittings (P/N 11887, item 22 shown on Hydraulic
Fittings and Clamps Assy.).
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 61
hydraulic fittings and clamps assy.
19
23
24
18
3
16
4
3
1
20
10
2
5
8
9
14
7
10
21
22
10
11
22
17
3
12
15
25
13
26
2
31
6
12
13
27
32
28
33
30
27
28
29
PAGE 62 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
hydraulic fittings and clamps assy.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
PART NO.
PART NAME
QTY.
REMARKS
21095
FITTING, STR 4MJ - 4MO
1
368817 FITTING, 90 4MJ - 4MO
2
37407
FITTING, 4mj x 6mo-90
4
15538
CLAMP, HOSE WORM #6, 7/16" TO 7/8" 2
37793
CLAMP ASSEMBLY, HOSE
1
37352
CLAMP ASSEMBLY, 5/16 HOSE
1
37792
CLAMP ASSEMBLY, HOSE
1
37433
CLAMP ASSEMBLY, HOSE
1
366437
FITTING, BULKHEAD #4 JIC
1
11721
FITTING, STR 6MJ - 6MO
4
12431
FITTING, 90 8MJ - 6MO
1
21115
FITTING, STR 6MJ - 6MO LONG
2
37405
FITTING, 10MO X - 6FO - ST
2
37406
FITTING, 6MJ X 10MO - ST
2
21159
FITTING, 45 4MJ - 4MO
1
367470
FITTING, STR 4MJ - 6MO
3
37788
FITTING, tee 4Mo - 4MO - 4mj
1
12546
FITTING, qd 4mo diagn parker pd 341
1
12148cap, dust diag parker pd6 - 285
1
35022 clamp, loop cushioned #8
1
37493fitting, orifice 4mj - 4mo x .100
1
11887
FITTING, STR 6MJ - 4MO.........................................2.................... SEE NOTE below
37399
4mj x 2mo-st
1
37400fitting, 6mj x 6mo-9oll
1
2623screw, hhc 5/16-18 x 1.25
4
37424cover plate, behringer stb-t2
4
37420
1/2" clamp, behringer t2050-pp
4
37423stack bolt, behringer stb-t2
6
37421
5/8" clamp, behringer t2062-pp
2
37422
1/2" x 5/8" clamp, behringer t2050/t2062-pp 3
37418top bolt, 5/16x18 x 2
1
37417cover plate, behringer cop-o
1
37416clamp, 5/16
1
NOTICE
FOR SAWS up to S/N ZD3700238 ONLY. When Ordering
hose (P/N 37347 item 7 on Hydraulic Hoses Assy.), also
order two (2) each fittings (P/N 11887, item 22 shown
on this page.
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 63
front pointer assy.
PAGE 64 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
front pointer assy.
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
PART NO.
37182
582008
500005
37178
926006
15503
110038
1456
10133
5070 B
933247
3233
37261
544002
125043-3
540039
10136
1665
0205
574003
574002
15173
13287
923199
37112
PART NAME
QTY.
REMARKS
POINTER
1
BUSHING, FLANGE 1.0 OD X .75 ID
4
WHEEL, POINTER 6" X 1"
1
AXLE, POINTER WHEEL
1
SCREW, SQHS CP 1/4 - 20 X1/2
2
KNOB, COMFORT GRIP STAR
1
SAW POINTER 15" RH FRONT
1
NUT, HEX FINISH 3/8 - 16
1
NUT, NYLOC 3/8 - 16.................................................1.................... SEE NOTE below
NUT, NYLOC 3/4 - 10
2
WASHER, FLAT SAE 3/4 GRD 9 YZ
2
WASHER, FENDER 1.50 OD X 3/8 ID
2
PLUG, FINISHING 3/4"
2
SHOULDER, ADAPTER............................................1.................... SEE NOTE below
RETAINER, SAW POINTER CABLE..........................1.................... SEE NOTE below
PULLEY, POINTER ROPE.........................................1.................... SEE NOTe below
WASHER, FLAT SAE 3/8...........................................2.................... SEE NOTE below
SCREW, HHC 3/8 - 16 X 2.........................................1.................... SEE NOTE below
SCREW, HHC 3/8 - 16 X 1.0
1
ROPE, POINTER assy.............................................1.................... includes ball & crimp
CAM CLEAT
1
WASHER, FLAT #8
2
NUT, NYLOC 8 - 32
2
SCREW, SHC 8 - 32 X 1-1/4
2
MOUNT, AIR FILTER
1
NOTICE
These parts are used only on "Type 1" Rope Guide Systems shown in illustration on Lift Bail Assy.
Type 2 Rope Guide System supercedes Type 1 Rope
Guide System. See illustration.
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 65
belt drive assy.
PAGE 66 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
belt drive assy.
NO. PART NO.
1
37001
3#
4
37019
5#
6#
7
37137
8
37002
9
37319
10
37320
11
923201
12
37267
13
21004-003
14
37755
15
460016
15
460023
16
10057-061
17
37269
18 37266
* 37218
19
20
582012
21
915315
22
915316
23
10138
24
926919
25
37268
26
933242
27
1456
28
37762
29
924289
30
10133
31
939978
32
938422
33
37177
33
37169
34
37176
34
37168
35
520007
36
540047
36
540041
36
540040
36
540035
36
540046
PART NAME
QTY.
REMARKS
PLATE, ENGINE ADAPTER-DEUTZ
1
SHAFT, ENGINE DRIVE-DEUTZ
1
PLATE, PULLEY DRIVE COVER
1
FLANGE, ENGINE DRIVE-DEUTZ
1
FLANGE, PULLEY DRIVE-DEUTZ
1
BELT TENSIONER ASSY...........................................1.................... includes items w/
*
PULLEY, PUMP DRIVE 3.75" A-SECTION
1
WASHER, THRUST 1.00 OD X .265 L X .265 H 1
SCREW, SHC 10-32 X 3/4
1
SCREW, SHC 1/4 - 20 X 1/2
8
SPACER, BELT TENSIONER
1
BELT, AX-35
1
SHOE, LOWER BELTSIDE
1
BUSHING, TAPER-LOCK 2517 X 1-7/8.....................1.................... FITS 20", 26", 30", 36"
BUSHING, TAPER-LOCK 2012 X 1-7/8.....................1.................... FITS 16"
KEY, 1/2" SQ X 3-1/2"
1
KEY, SQUARE 1/8 X 3/4
1
SCREW, MODIFIED HEAD 3/8 X 1-3/4
1
GUARD, PUMP DRIVE..............................................1.................... safety item
BUSHING, QUICK DISCONNECT BLADE SHAFT 2
SCREW, HHC 5/8 - 11 X 3 GR8
1
SCREW, HHC 5/8 - 11 X 3 LH GR8
1
SCREW, SHS 1/4 - 20 X 1/2 NP
1
PIN, DOWEL 1/4 X 3/4
1
STUD, 3/8 - 16 X 3 SELF-LOCKING
1
WASHER, FLAT SAE 3/8 GRD 9 YZ
5
NUT, HEX FINISH 3/8 - 16
4
STUD, 1/2 - 13 X 1-3/4
1
SCREW, FHSC 3/8 - 16 X 1-3/4
2
NUT, NYLOC 3/8 - 16
2
SCREW, FHSC M10 - 1.5 X 25MM NP
11
SCREW, HHC M10 - 1.0 X 50MM 10.9 NP
8
FLANGE ASSY, 6.0" OUTER BLADE........................2............... FITS 30", 36" BELT DRIVE
FLANGE ASSY, 5.0" OUTER BLADE........................2............... FITS 16", 20", 26" BELT DRIVE
FLANGE ASSY, 6.0" INNER BLADE.........................2............... FITS 30", 36" BELT DRIVE
FLANGE ASSY, 5.0" INNER BLADE.........................2............... FITS 16", 20", 26" BELT DRIVE
V-BELT, 5G 3 VX 530 POWERBAND
2
PULLEY, 5.6 10G 3V X 2517 TAPER.........................1............... FITS 36" BELT DRIVE
PULLEY, 5.3 10G 3V X 2517 TAPER.........................1............... FITS 30" BELT DRIVE
PULLEY, 5.0 10G 3V X 2517 TAPER.........................1............... FITS 26" BELT DRIVE
PULLEY, 4.75 10G 3V X 2517 TAPER.......................1............... FITS 20" BELT DRIVE
PULLEY, 4.2 10G 3V X 2012 TAPER.........................1............... FITS 16" BELT DRIVE
CONTINUED NEXT PAGE
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 67
belt drive assy. (CONTINUED)
PAGE 68 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
belt drive assy. (CONTINUED)
NO.
37
38
39
40
41
42
43
44
45
PART NO.
37134
926790
25992
37735
37734
37763
915103
37756
37833
PART NAME
QTY.
REMARKS
BLADE SHAFT ASSY.
1
PIN, DOWEL 3/8 X 1-3/4....................................... 2...................included w/ item 33
SCREW, SHC 12 - 24 X 1/2
4
RING, FAN MOUNT
1
FAN, CW 8" 10 BLADE
1
STUD, 1/2 - 13 X 5-1/2
1
SCREW, HHC 3/8 - 16 X 3/4 GR8 YZ
2
SHOE, UPPER BELTSIDE
1
SPLINED DRIVE ASSY.......................................... 1...................INCLUDES ITEMS W/#
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 69
drive pulley assy.
PAGE 70 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
drive pulley assy.
NO. PART NO.
1*
37011
1#
37154
2*# 37003
3*# 37028
4*# 37090
5*# 37017
6*# 37092
7*# 37035
8*# 915004
9*# 933240
10
37103
10
37321
PART NAME
QTY.
REMARKS
PULLEY, 3.3 10 3V 4.5 1A.........................................1............... FITS 26", 30", 36" BELT DRIVE
PULLEY, 4.1 3V 4.5 1A..............................................1............... FITS 16", 20" BELT DRIVE
SUPPORT, ENGINE DRIVE BEARING
1
BEARING, TAPERED ROLLER NSK #32007XJ 2
SPRING, SMALLEY WAVO RW-0162
1
FLANGE, ENGINE DRIVE BEARING SUPPORT 1
SEAL, CR 17753
2
SCREW, SHC 4-40 X 3/8
4
SCREW, HHC 1/4 - 20 X 7/8 GR8 YZ
8
WASHER, FLAT SAE 1/4 GRD 9 YZ
8
DRIVE PULLEY ASSY., 3.3 10 3V 4.5 1A.................1............... FITS 26", 30", 36" BELT DRIVE
.................................................................................................... includes items w.
DRIVE PULLEY ASSY., 4.1 3V 4.5 1A......................1............... FITS 16", 20" BELT DRIVE
.................................................................................................... includes items w/#
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 71
bladeshaft assy.
PAGE 72 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
bladeshaft assy.
NO.
1*
2*
3*
4*
5*
6*
7*
8*
9*
10*
11*
12*
13*
14*
15*
16*
17*
18*
19*
20*
21
PART NO.
37108
37111
06502-010
933243
421001
583026
577009
25695
25690
460010
39460011
480006
480007
485003
486001
576006
578135
576007
10138
927048
37134
PART NAME
QTY.
REMARKS
HOUSING, BLADESHAFT
1
BLADESHAFT, 7000 SERIES
1
SCREW, HHC 7/16 - 14 X 1-1/4
6
WASHER FLAT SAE 7/16 GRD 9 YZ
6
SENSOR, HALL EFFECT SPEED PICKUP
1
DRAIN PLUG, MAGNETIC 1/2 - 20
1
GASKET, DRAIN PLUG
1
WASHER, SEAL 3/4"
1
GEAR, SAW BLADE SHAFT SPEED PICKUP
1
BEARING, ROLLER KOYO # 7210BGC3
2
BEARING, BALL KOYO # NU2210RC3
1
SEAL, OIL CR# 28655
2
SEAL, OIL CR- 19599
2
SLEEVE, BLADE SHAFT SEAL
2
WASHER, THRUST 6000 SERIES
2
SNAP RING, VITON # AS-135
2
O-RING, VITON # AS-135
2
SNAP RING, VHO-354
1
SCREW, SHS 1/4 - 20 X 1/2
6
KEY, WOODRUFF #807 1/4 X 7/8
2
BLADESHAFT ASSEMBLY........................................1.................... includes items w/*
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 73
16", 20", 26" bladeguard assy.
PAGE 74 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
16", 20", 26" bladeguard assy.
NO. PART NO.
PART NAME
QTY.
REMARKS
1@ 200004
BLADEGUARD W/A, 16" REAR HALF
1
1#
200008
BLADEGUARD W/A, 20" REAR HALF
1
1$
200010
BLADEGUARD W/A, 26" REAR HALF
1
2@ 200003
BLADEGUARD W/A, 16" FRONT HALF
1
2#
200007
BLADEGUARD W/A, 20" FRONT HALF
1
2$
200009
BLADEGUARD W/A, 26" FRONT HALF
1
3@#$ 582040
BUSHING, BLADEGUARD HINGE DELRIN
1
4@#$ 200019
FLAP,MUD BLADEGUARD........................................1.................... safety item
5@#$ 37394
MANIFOLD, WATER SMALL
1
6@#$ 2113
FITTING, PLUG 1/8MP HEX SKT HD
1
7@#$ 370456
FITTING, BRASS 6BARB-1/4MP
2
8@#$ 10176
NUT, NYLOC 1/2-13
1
9@#$ 10024
NUT, NYLOC 1/4-20
3
10@#$ 0131 A
SCREW, HHC 1/4 - 20 X 3/4
1
11@#$ 06503-026
SCREW, HHC 1/2 - 13 X 3-1/4
1
12@#$ 26250
SCREW, HHC 1/4 - 20 X 1-3/4
2
13@#$ 10930
WASHER, FENDER 1/4 X 1-1/4
1
14@#$ 37396
3/8" QC MALE
1
15@# 37506
HOSE, WATER #6 LP, 16", 20" BLADEGUARD
2
15$ 37508
HOSE, WATER #6 LP, 26" BLADEGUARD
2
16@#$ 22129-001
PIPE STRAP 3/8
2
17@#$ 1618
NUT, NYLOC 10-24
2
18@#$ 923144
SCREW, SHC 10-24 X 1/2
2
19bg1600guard, 16" streetpro 3/6/7 std flange........1.................... safety item
......................................................................................................... includes items w/@
......................................................................................................... contact mq unit sales
19bg2000guard, 20" streetpro 3/6/7 std flange........1.................... safety item
......................................................................................................... includes items w/#
......................................................................................................... contact mq unit sales
19bg2600guard, 26" streetpro 3/6/7 std flange........1.................... safety item
......................................................................................................... includes items w/$
......................................................................................................... contact mq unit sales
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 75
30", 36" bladeguard assy.
PAGE 76 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
30", 36" bladeguard assy.
NO. PART NO.
PART NAME
QTY.
REMARKS
1@ 200012
BLADEGUARD W/A, 30" REAR HALF
1
1#
200014
BLADEGUARD W/A, 36" REAR HALF
1
2*
200011
BLADEGUARD W/A, 30" front HALF
1
2#
200013
BLADEGUARD W/A, 36" FRONT HALF
1
3@# 582039
BUSHING, BLADEGUARD HINGE DELRIN
1
4@# 37395
MANIFOLD, WATER large
1
5@# 200019
FLAP,MUD BLADEGUARD........................................1.................... safety item
6@# 0131 A
SCREW, HHC 1/4 - 20 X 3/4
1
7@# 26250
SCREW, HHC 1/4 - 20 X 1-3/4
2
8@# 06503-030
SCREW, HHC 1/2 - 13 X 3-3/4
1
9@# 10176
NUT, NYLOC 1/2-13
1
10@# 10024
NUT, NYLOC 1/4-20
3
11@# 10930
WASHER, FENDER 1/4 X 1-1/4
1
12@# 370456
FITTING, BRASS 6BARB-1/4MP
2
13@# 2113
FITTING, PLUG 1/8MP HEX SKT HD
1
14@# 37396
3/8" QC MALE
1
15@# 1618
NUT, NYLOC 10-24
2
16@# 923144
SCREW, SHC 10-24 X 1/2
2
17@# 22129-001
PIPE STRAP 3/8
2
18@ 37509
HOSE, WATER #6 LP, 30" BLADEGUARD
2
18# 37510
HOSE, WATER #6 LP, 36" BLADEGUARD
2
19bg3000guard, 30" streetpro 3/6/7 std flange........1.................... safety item
......................................................................................................... includes items w/@
......................................................................................................... contact mq unit sales
19bg3600guard, 36" streetpro 3/6/7 std flange........1.................... safety item
......................................................................................................... includes items w/#
......................................................................................................... contact mq unit sales
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 77
optional weight kit assy.
PAGE 78 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
optional weight kit assy.
NO.
1
PART NO.
PART NAME
37829weight kit
QTY.
1
REMARKS
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 79
terms and conditions of sale — parts
PAYMENT TERMS
5.
Parts must be in new and resalable
condition, in the original Multiquip
package (if any), and with Multiquip part
numbers clearly marked.
6.
The following items are not returnable:
Multiquip reserves the right to quote and
sell direct to Government agencies, and to
Original Equipment Manufacturer accounts
who use our products as integral parts of their
own products.
a.
SPECIAL EXPEDITING SERVICE
Terms of payment for parts are net 30 days.
FREIGHT POLICY
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and
the carrier.
b.
MINIMUM ORDER
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
RETURNED GOODS POLICY
Return shipments will be accepted and
credit will be allowed, subject to the following
provisions:
1.
A Returned Material Authorization
must be approved by Multiquip prior to
shipment.
2.
Obsolete parts. (If an item is in the
price book and shows as being
replaced by another item, it is
obsolete.)
Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
c.
Any line item with an extended
dealer net price of less than
$5.00.
d.
Special order items.
e.
Electrical components.
f.
Paint, chemicals, and lubricants.
g.
Decals and paper products.
h.
Items purchased in kits.
7.
The sender will be notified of any material
received that is not acceptable.
To obtain a Return Material Authorization,
a list must be provided to Multiquip
Parts Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
8.
Such material will be held for five
working days from notification, pending
instructions. If a reply is not received
within five days, the material will be
returned to the sender at his expense.
a.
The parts numbers and descriptions
must match the current parts price
list.
9.
b.
The list must be typed or computer
generated.
Credit on returned parts will be issued
at dealer net price at time of the original
purchase, less a 15% restocking
charge.
c.
The list must state the reason(s)
for the return.
d.
The list must reference the sales
order(s) or invoice (s) under
which the items were originally
purchased.
e.
The list must include the name
and phone number of the person
requesting the RMA.
3.
A copy of the Return Material Authorization
must accompany the return shipment.
4.
Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
A $35.00 surcharge will be added to the
invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
LIMITATIONS OF SELLER’S LIABILITY
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of
the item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
LIMITATION OF WARRANTIES
No warranties, express or implied, are
made in connection with the sale of parts or
trade accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes nor
authorizes any person to assume for it
any other obligation or liability whatever in
connection with the sale of its products. Apart
from such written statement of warranty,
there are no warranties, express, implied or
statutory, which extend beyond the description
of the products on the face hereof.
Effective: February 22, 2006
11. Credit issued will be applied to future
purchases only.
PRICING AND REBATES
Prices are subject to change without prior
notice. Price changes are effective on a
specific date and all orders received on or
after that date will be billed at the revised price.
Rebates for price declines and added charges
for price increases will not be made for stock
on hand at the time of any price change.
PAGE 80 — SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)
notes
SP7060 SERIES MULTIQUIP SAW — PARTS MANUAL — REV. #5 (05/06/11)— PAGE 81
Parts Manual
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
UNITED STATES
Multiquip Corporate Office
18910 Wilmington Ave.
Carson, CA 90746
Contact: mq@multiquip.com
MQ Parts Department
Tel. (800) 421-1244
Fax (800) 537-3927
Service Department
800-421-1244
310-537-3700
800-427-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Warranty Department
Fax: 310-537-4259
800-421-1244
310-537-3700
Fax: 310-537-1173
Technical Assistance
800-478-1244
Fax: 310-943-2238
MEXICO
UNITED KINGDOM
MQ Cipsa
Multiquip (UK) Limited Head Office
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: pmastretta@cipsa.com.mx
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Unit 2, Northpoint Industrial Estate,
Globe Lane,
Dukinfield, Cheshire SK16 4UJ
Contact: sales@multiquip.co.uk
Tel: 0161 339 2223
Fax: 0161 339 3226
CANADA
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: jmartin@multiquip.com
Tel: (450) 625-2244
Tel: (877) 963-4411
Fax: (450) 625-8664
© COPYRIGHT 2011, MULTIQUIP INC.
Multiquip Inc and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property
of their respective owners and used with permission.
This manual MUsT accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.
Your Local Dealer is: