Mircom FA-300-6L Series Specifications

SRM-312 Series
Remote Relay
FA-300 SERIES
REMOTE RELAY
Installation and Operation Manual
LT-1001 Rev. 5
July 2014
1.0
Introduction
5
2.0
Mechanical Installation
5
3.0
Functional Setup
6
3.1
Jumpers ......................................................................................................................... 6
3.2
DIP Switches .................................................................................................................. 7
3.2.1
Dip Switch DSW1-1 to 1-3 ............................................................................................. 7
3.2.2
Dip Switch DSW1-4 ....................................................................................................... 7
3.2.3
Dip Switch DSW1-5 (FR-320 only) ................................................................................ 8
3.2.4
Dip Switch DSW1-6 ....................................................................................................... 8
3.2.5
Dip Switch DSW1-7 (FX-350/351 and FX-3500/3500RCU only) ................................... 8
3.2.6
Dip Switch DSW1-8 ....................................................................................................... 8
4.0
Configuration of the Relays
8
5.0
Wiring
9
6.0
Specifications & Features
10
6.1
Enclosure: ...................................................................................................................... 10
6.2
Electrical Specifications ................................................................................................. 10
6.3
Current Drain for Battery Calculations: .......................................................................... 10
7.0
Warranty and Warning Information
7.1
Warning Please Read Carefully ..................................................................................... 11
11
7.2
Note to Installers ............................................................................................................ 11
7.3
System Failures ............................................................................................................. 11
7.3.1
Inadequate Installation ................................................................................................... 11
7.3.2
Power Failure ................................................................................................................. 11
7.3.3
Failure of Replaceable Batteries .................................................................................... 11
7.3.4
Compromise of Radio Frequency (Wireless) Devices ................................................... 12
7.3.5
System Users ................................................................................................................. 12
7.3.6
Automatic Alarm Initiating Devices ................................................................................ 12
7.3.7
Software ......................................................................................................................... 12
7.3.8
Alarm Notification Appliances ........................................................................................ 12
7.3.9
Telephone Lines ............................................................................................................ 13
7.3.10
Insufficient Time ............................................................................................................. 13
7.3.11
Component Failure ........................................................................................................ 13
7.3.12
Inadequate Testing ........................................................................................................ 13
7.3.13
Security and Insurance .................................................................................................. 13
7.4
Limited Warranty ............................................................................................................ 13
3
4
7.4.1
International Warranty .................................................................................................... 13
7.4.2
Conditions to Void Warranty .......................................................................................... 14
7.5
Warranty Procedure ....................................................................................................... 14
7.6
Disclaimer of Warranties ................................................................................................ 14
7.7
Out of Warranty Repairs ................................................................................................ 14
Introduction
1.0
Introduction
The Model SRM-312 Smart Relay Module provides twelve supervised configurable relays and
comes complete with a white SRM-312W or red enclosure SRM-312R.
2.0
Mechanical Installation
To mount the SRM-312 open the front door, and mount the backbox to the wall using the four
screws provided. This enclosure may also be mounted to a 4” square electrical box. There are
two conduit areas provided at the bottom of the enclosure.
8.2"
6.3"
0.75”
FOUR
MOUNTING
HOLES
7.5"
9.0
2“ KNOCKOUT
1.5"
Figure 1
SRM-312 Mounting Dimensions
5
Functional Setup
3.0
Functional Setup
Place 120
EOL
Jumper
JW51ohm
is used
on resistor
last
betweenONLY.
+ andRemove
- on theallRSSRM-312
485 on
last wired
JW51
jumpers
exceptSRM-312
for the
last
address.
only.
DIP Switch for
relay address
S
A
Z9
S
9&10
8&9
RLY. 10
Z10
A
S
RLY. 11
A
Z11
S
11&12
10&11
RLY. 12
Z12
A
S
NO N C
A
12
4 5 6 7 8
24VDC
+IN/OUT-
Leave jumpers JW48,
JW49 and JW50 intact
on board.
Z1
S
1&2
A
RLY. 1
Z2
S
2&3
A
RLY. 2
Z3
S
3&4
A
Z4
S
4&5
A
RLY. 3
RLY. 4
Z5
S
5&6
A
RLY. 5
Z6
S
6&7
A
NC N O
CPU FAIL
NC NO
PWR ON
NC NO
JW48
INDIVIDUAL
RELAY STATUS
GREEN LEDS
DSCNN
TX/RX
NC NO
JW50
DSW1
JW49
NC NO
1 2 3
P4 is for factory
use only
RLY. 8
Z8
Relay jumpers for
programming
ON
NC NO
P4
S
C NO/NC C NO/NC
NO NC
JW51
A
RLY. 9
NO N C
RLY. 7
Z7
7&8
C NO/NC C NO/NC
NO NC
C NO/NC C NO/NC
S
NO N C
-
NO NC
+
RS-485 IN/OUT
RLY. 6
C NO/NC C NO/NC C NO/NC C NO/NC C NO/NC C NO/NC
Wire 24 Volts from filtered Auxiliary
Power at the Fire Alarm Panel.
LEDs:
DSCNN - if enabled (via DIP switch DSW1-4), this LED illuminates steadily (amber) when auxiliary disconnect is activated
at the Fire Alarm Panel.
TX/RX - transmit/receive LED flashes (green as long as there is communication with the Fire Alarm Panel.
PWR ON - illuminates steadily (green) as long as there is power to the relay board.
CPU FAIL - will illuminate steadily (amber) when CPU fails at the Fire Alarm Panel.
Figure 2
3.1
SRM-312 Board Layout
Jumpers
Table 1 Jumper Settings
6
Jumper
Jumper Function
JW48
FACTORY USE ONLY (JUMPER INSTALLED)
JW49
FACTORY USE ONLY (JUMPER INSTALLED)
JW50
FACTORY USE ONLY (JUMPER INSTALLED)
Functional Setup
3.2
DIP Switches
!
Attention: Dip Switch DSW 1-6 and DSW 1-8 are always to be set to OFF.
There is one bank of DIP switches to be set. DSW1 is found at the top left hand corner and is
used to select the smart relay address. Valid addresses are 1 to 6 inclusive, for FA-300 Series
and FR-320 Series Fire Alarm Panels; 1 to 7 inclusive for FX-350/351 and FX-3500/FX3500RCU Series. Set address as described in 3.2.1 Dip Switch DSW1-1 to 1-3.
3.2.1 Dip Switch DSW1-1 to 1-3
Table 2 SRM-312 DIP Switch Address Setup
Address
DSW1-1
DSW1-2
DSW1-3
1
ON
OFF
OFF
2
OFF
ON
OFF
3
ON
ON
OFF
4
OFF
OFF
ON
5
ON
OFF
ON
6
OFF
ON
ON
ON
ON
ON
7
(FX-350/351
and
FX-3500/3500RCU)
3.2.2 Dip Switch DSW1-4
Used to disable the Auxiliary Disconnect function from the Fire Alarm Panel.
Table 3 Enable or Disable Auxiliary Disconnect Function
DSW1-4 Position
Function
ON
Enable auxiliary disconnect function from the fire alarm panel.
OFF
Disable auxiliary disconnect function from the fire alarm panel (Aux. disconnect
will not disconnect these twelve relays). This is the default setting. The DSCNN
(Aux Disconnect) LED is not active when Aux Disconnect is active on the Fire
Alarm Control Panel in this mode.
7
Configuration of the Relays
3.2.3 Dip Switch DSW1-5 (FR-320 only)
Used to enable added support for hazard zone message for the FR-320. This option is
enabled by putting DSW1-5 to the “ON” position.When this option is enabled, relay 1 to 6 will
show the status for Hazard Area 1 and Hazard Area 2 as shown in the table below.
Table 4 Enabled FR-320 Hazard Area Status Description
Hazard Area 1
Hazard Area 2
RLY1
RLY2
RLY3
RLY4
RLY5
RLY6
Alert
Alarm
Release
Alert
Alarm
Release
3.2.4 Dip Switch DSW1-6
Always set to OFF.
3.2.5 Dip Switch DSW1-7 (FX-350/351 and FX-3500/3500RCU only)
Used to enable 16 bit checksum for supporting the FX-350/351 and FX-3500/3500RCU
panels. This option is enabled by putting DSW1-7 switch to the “ON” position.
3.2.6 Dip Switch DSW1-8
Always set to OFF.
4.0
Configuration of the Relays
The twelve Relays may be configured to operate alone or in combination with other relays on
the board. This configuration is accomplished by jumper selection on the Smart Relay module.
The following illustration explains how the relays are configured.
ZONE JUMPER
installed: turns on relay when the zone
(1) is active
removed: does not turn on the relay when
zone (1) is active
Default: Jumper is installed
SUPV/ALARM SELECTION
S: Relay turns on when common
supervisory is active
A: Relay turns on when common
alarm is active
Default: Jumper is NOT installed,
connected on center pin only
LED (GREEN)
RELAY
LOGICAL OR WITH ADJACENT ZONE
jumper installed: this relay 1 works in
conjunction with relay 2
jumper removed: relay 1 does not
operate with the adjacent relay 2
chaining example: if jumper is installed
on 1&2 and 2&3 then all the three relays
will be on if any one of relays 1,2 or 3 is
active
Default: No jumper installed, connected
on one pin only
Figure 3
8
1&2
A
S
NO NC
Z1
RELAY 1
NO/NC
NC/NO CONNECTION
NC: terminal provides normally closed contacts
NO: terminal provides normally open contacts
Default: jumper is installed on normally open (NO)
Note: if the jumper is not installed on any selection,
then the relay is not connected to the terminals
RELAY 6
C
Relay Configuration
NO/NC
C
Wiring
5.0
Wiring
Wire from the last SRM-312 to the next SRM-312 and so on; then from the first SRM-312 to
the Fire Alarm Panel. There are only two connections to be made, one for power and one for
the RS-485 loop.
i
Note:
Ensure that the 120 E.O.L. resistor is connected to the RS-485 positive and
negative terminals on the last SRM-312.
The RS-485 Wiring to the SRM-312 is recommended to be Twisted Shielded Pair. The wire
gauge may be:
•
22 AWG up to2000 ft.
•
20 AWG up to4000 ft.
The 24V DC field wiring needs to be of an appropriate gauge for the number of smart relays
and the total wiring run length. See Current Drain for Battery Calculations, page 10 and
calculate the Maximum current for all smart relays summed together.
i
Note:
!
All circuits are power limited and must use type FPL, FPLR or FPLP Power
Limited Cable.
Caution:
Accidentally connecting any of the 24V DC wires to the RS-485
wiring will result in damage to the Annunciator and/or to the Fire
Alarm Control Panel to which it is connected.
Table 5 Wiring Table
Total
Maximum
Current
MAXIMUM WIRING RUN TO LAST DEVICE (ELR)
18AWG
16AWG
14AWG
12AWG
MAX. LOOP
RESISTANCE
Amperes
ft
m
ft
m
ft
m
ft
m
Ohms
0.06
2350
716
3750
1143
6000
1829
8500
2591
30
0.12
1180
360
1850
567
3000
915
4250
1296
15
0.30
470
143
750
229
1200
366
1900
579
6
0.60
235
71
375
114
600
183
850
259
3
0.90
156
47
250
76
400
122
570
174
2
1.20
118
36
185
56
300
91
425
129
1.5
1.50
94
29
150
46
240
73
343
105
1.2
1.70
78
24
125
38
200
61
285
87
1.0
9
Specifications & Features
6.0
Specifications & Features
6.1
Enclosure:
•
6.2
6.3
Enclosure may be mounted on a 4” square Electrical Box or on a wall.
Electrical Specifications
•
24 VDC nominal voltage.
•
Common LEDs DISCNN (Aux. Disconnect), TX/RX (Transmit/Receive), PWR ON, CPU
FAIL and individual relay status LED indicators.
•
28V DC, 1A maximum per contact (resistive load)
•
12 programmable relays available.
•
Not Expandable.
•
Standby 30 mA Max., Alarm 140 mA Max. All LEDs illuminated 140 mA Max.
Current Drain for Battery Calculations:
The maximum normal current drain will be during Lamp Test when all lamps are illuminated on
one chassis at a time. Thus the currents are:
Normal Standby = 30 mA
Maximum = 140mA
The Normal Standby Current is used for Battery Size Calculations (see the FA-300/FR-320,
FX-350/351 Series, or the FX-3500/FX-3500RCU Fire Alarm Control Panel manual for battery
calculations) and includes the current drain for the common LEDs. The Maximum Current is
used to calculate the wire size (see Wiring on page 9).
10
Warranty and Warning Information
7.0
Warranty and Warning Information
7.1
i
7.2
Warning Please Read Carefully
Note:
This equipment is subject to terms and conditions of sale as follows:
Note to Installers
This warning contains vital information. As the only individual in contact with system users, it is
your responsibility to bring each item in this warning to the attention of the users of this
system. Failure to properly inform system end-users of the circumstances in which the system
might fail may result in over-reliance upon the system. As a result, it is imperative that you
properly inform each customer for whom you install the system of the possible forms of failure.
7.3
System Failures
This system has been carefully designed to be as effective as possible. There are
circumstances, such as fire or other types of emergencies where it may not provide protection.
Alarm systems of any type may be compromised deliberately or may fail to operate as
expected for a variety of reasons. Some reasons for system failure include:
7.3.1 Inadequate Installation
A Fire Alarm system must be installed in accordance with all the applicable codes and
standards in order to provide adequate protection. An inspection and approval of the initial
installation, or, after any changes to the system, must be conducted by the Local Authority
Having Jurisdiction. Such inspections ensure installation has been carried out properly.
7.3.2 Power Failure
Control units, smoke detectors and many other connected devices require an adequate power
supply for proper operation. If the system or any device connected to the system operates
from batteries, it is possible for the batteries to fail. Even if the batteries have not failed, they
must be fully charged, in good condition and installed correctly. If a device operates only by
AC power, any interruption, however brief, will render that device inoperative while it does not
have power. Power interruptions of any length are often accompanied by voltage fluctuations
which may damage electronic equipment such as a fire alarm system. After a power
interruption has occurred, immediately conduct a complete system test to ensure that the
system operates as intended.
7.3.3 Failure of Replaceable Batteries
Systems with wireless transmitters have been designed to provide several years of battery life
under normal conditions. The expected battery life is a function of the device environment,
usage and type. Ambient conditions such as high humidity, high or low temperatures, or large
temperature fluctuations may reduce the expected battery life. While each transmitting device
has a low battery monitor which identifies when the batteries need to be replaced, this monitor
11
Warranty and Warning Information
may fail to operate as expected. Regular testing and maintenance will keep the system in
good operating condition.
7.3.4 Compromise of Radio Frequency (Wireless) Devices
Signals may not reach the receiver under all circumstances which could include metal objects
placed on or near the radio path or deliberate jamming or other inadvertent radio signal
interference.
7.3.5 System Users
A user may not be able to operate a panic or emergency switch possibly due to permanent or
temporary physical disability, inability to reach the device in time, or unfamiliarity with the
correct operation. It is important that all system users be trained in the correct operation of the
alarm system and that they know how to respond when the system indicates an alarm.
7.3.6 Automatic Alarm Initiating Devices
Smoke detectors, heat detectors and other alarm initiating devices that are a part of this
system may not properly detect a fire condition or signal the control panel to alert occupants of
a fire condition for a number of reasons, such as: the smoke detectors or heat detector may
have been improperly installed or positioned; smoke or heat may not be able to reach the
alarm initiating device, such as when the fire is in a chimney, walls or roofs, or on the other
side of closed doors; and, smoke and heat detectors may not detect smoke or heat from fires
on another level of the residence or building.
7.3.7 Software
Most Mircom products contain software. With respect to those products, Mircom does not
warranty that the operation of the software will be uninterrupted or error-free or that the
software will meet any other standard of performance, or that the functions or performance of
the software will meet the user’s requirements. Mircom shall not be liable for any delays,
breakdowns, interruptions, loss, destruction, alteration or other problems in the use of a
product arising our of, or caused by, the software.
Every fire is different in the amount and rate at which smoke and heat are generated. Smoke
detectors cannot sense all types of fires equally well. Smoke detectors may not provide timely
warning of fires caused by carelessness or safety hazards such as smoking in bed, violent
explosions, escaping gas, improper storage of flammable materials, overloaded electrical
circuits, children playing with matches or arson.
Even if the smoke detector or heat detector operates as intended, there may be circumstances
when there is insufficient warning to allow all occupants to escape in time to avoid injury or
death.
7.3.8 Alarm Notification Appliances
Alarm Notification Appliances such as sirens, bells, horns, or strobes may not warn people or
waken someone sleeping if there is an intervening wall or door. If notification appliances are
located on a different level of the residence or premise, then it is less likely that the occupants
will be alerted or awakened. Audible notification appliances may be interfered with by other
noise sources such as stereos, radios, televisions, air conditioners or other appliances, or
passing traffic. Audible notification appliances, however loud, may not be heard by a hearingimpaired person.
12
Warranty and Warning Information
7.3.9 Telephone Lines
If telephone lines are used to transmit alarms, they may be out of service or busy for certain
periods of time. Also the telephone lines may be compromised by such things as criminal
tampering, local construction, storms or earthquakes.
7.3.10 Insufficient Time
There may be circumstances when the system will operate as intended, yet the occupants will
not be protected from the emergency due to their inability to respond to the warnings in a
timely manner. If the system is monitored, the response may not occur in time enough to
protect the occupants or their belongings.
7.3.11 Component Failure
Although every effort has been made to make this system as reliable as possible, the system
may fail to function as intended due to the failure of a component.
7.3.12 Inadequate Testing
Most problems that would prevent an alarm system from operating as intended can be
discovered by regular testing and maintenance. The complete system should be tested as
required by national standards and the Local Authority Having Jurisdiction and immediately
after a fire, storm, earthquake, accident, or any kind of construction activity inside or outside
the premises. The testing should include all sensing devices, keypads, consoles, alarm
indicating devices and any other operational devices that are part of the system.
7.3.13 Security and Insurance
Regardless of its capabilities, an alarm system is not a substitute for property or life insurance.
An alarm system also is not a substitute for property owners, renters, or other occupants to act
prudently to prevent or minimize the harmful effects of an emergency situation.
IMPORTANT NOTE: End-users of the system must take care to ensure that the system,
batteries, telephone lines, etc. are tested and examined on a regular basis to ensure the
minimization of system failure.
7.4
Limited Warranty
Mircom Technologies Ltd. together with its subsidiaries and affiliates (collectively, the “Mircom
Group of Companies”) warrants the original purchaser that for a period of three years from the
date of shipment, the product shall be free of defects in materials and workmanship under
normal use. During the warranty period, Mircom shall, at its option, repair or replace any
defective product upon return of the product to its factory, at no charge for labor and materials.
Any replacement and/or repaired parts are warranted for the remainder of the original warranty
or ninety (90) days, whichever is longer. The original owner must promptly notify Mircom in
writing that there is defect in material or workmanship, such written notice to be received in all
events prior to expiration of the warranty period.
7.4.1 International Warranty
The warranty for international customers is the same as for any customer within Canada and
the United States, with the exception that Mircom shall not be responsible for any customs
fees, taxes, or VAT that may be due.
13
Warranty and Warning Information
7.4.2 Conditions to Void Warranty
This warranty applies only to defects in parts and workmanship relating to normal use. It does
not cover:
7.5
•
damage incurred in shipping or handling;
•
damage caused by disaster such as fire, flood, wind, earthquake or lightning;
•
damage due to causes beyond the control of Mircom such as excessive voltage,
mechanical shock or water damage;
•
damage caused by unauthorized attachment, alterations, modifications or foreign
objects;
•
damage caused by peripherals (unless such peripherals were supplied by Mircom);
•
defects caused by failure to provide a suitable installation environment for the products;
•
damage caused by use of the products for purposes other than those for which it was
designed;
•
damage from improper maintenance;
•
damage arising out of any other abuse, mishandling or improper application of the
products.
Warranty Procedure
To obtain service under this warranty, please return the item(s) in question to the point of
purchase. All authorized distributors and dealers have a warranty program. Anyone returning
goods to Mircom must first obtain an authorization number. Mircom will not accept any
shipment whatsoever for which prior authorization has not been obtained. NOTE: Unless
specific pre-authorization in writing is obtained from Mircom management, no credits will be
issued for custom fabricated products or parts or for complete fire alarm system. Mircom will at
its sole option, repair or replace parts under warranty. Advance replacements for such items
must be purchased.
Note: Mircom’s liability for failure to repair the product under this warranty after a reasonable
number of attempts will be limited to a replacement of the product, as the exclusive remedy for
breach of warranty.
7.6
Disclaimer of Warranties
This warranty contains the entire warranty and shall be in lieu of any and all other warranties,
whether expressed or implied (including all implied warranties of merchantability or fitness for
a particular purpose) And of all other obligations or liabilities on the part of Mircom neither
assumes nor authorizes any other person purporting to act on its behalf to modify or to change
this warranty, nor to assume for it any other warranty or liability concerning this product.
This disclaimer of warranties and limited warranty are governed by the laws of the province of
Ontario, Canada.
7.7
Out of Warranty Repairs
Mircom will at its option repair or replace out-of-warranty products which are returned to its
factory according to the following conditions. Anyone returning goods to Mircom must first
14
Warranty and Warning Information
obtain an authorization number. Mircom will not accept any shipment whatsoever for which
prior authorization has not been obtained.
Products which Mircom determines to be repairable will be repaired and returned. A set fee
which Mircom has predetermined and which may be revised from time to time, will be charged
for each unit repaired.
Products which Mircom determines not to be repairable will be replaced by the nearest
equivalent product available at that time. The current market price of the replacement product
will be charged for each replacement unit.
The preceding information is accurate as of the date of publishing and is subject to change or revision
without prior notice at the sole discretion of the Company.
WARNING: Mircom recommends that the entire system be completely tested on a regular basis.
However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical
disruption, it is possible for this product to fail to perform as expected.
NOTE: Under no circumstances shall Mircom be liable for any special, incidental, or consequential
damages based upon breach of warranty, breach of contract, negligence, strict liability, or any
other legal theory. Such damages include, but are not limited to, loss of profits, loss of the product
or any associated equipment, cost of capital, cost of substitute or replacement equipment,
facilities or services, down time, purchaser’s time, the claims of third parties, including
customers, and injury to property.
MIRCOM MAKES NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE WITH RESPECT TO ITS GOODS DELIVERED, NOR IS THERE ANY OTHER WARRANTY,
EXPRESSED OR IMPLIED, EXCEPT FOR THE WARRANTY CONTAINED HEREIN.
15
CANADA - Main Office
25 Interchange Way
Vaughan, ON L4K 5W3
Tel: (888) 660-4655
(905) 660-4655
Fax: (905) 660-4113
U.S.A
4575 Witmer Industrial Estates
Niagara Falls, NY 14305
Tel: (888) 660-4655
Fax: (888) 660-4113
TECHNICAL SUPPORT
North America
Tel: (888) Mircom5
(888) 647-2665
International
Tel: (905) 660-4655
© Mircom 2014
Printed in Canada
Subject to change without prior notice
www.mircom.com