Miles Industries 738BXN (NG) Owner`s manual

LEGEND
Gravity Vent Gas Insert
738BXN (NG) & 738BXP (LPG)
Installation & Owner’s Manual
INSTALLE R
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
WARNING: If the information in these
instructions is not followed exactly, a fire
or explosion may result causing property
damage, personal injury or loss of life.
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light the appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Immediately call your gas supplier from
a neighbor’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier, call
the fire department.
Installation and service must be performed
by a qualified installer, service agency or the
gas supplier.
Leave t hi s m an u a l
w i t h t he appl i a n c e .
CONSUME R
Ret ai n t hi s m a n u a l
f or f ut ur e r ef e re n c e .
Please read this manual BEFORE installing
and operating this appliance.
This appliance may be installed in an aftermarket permanently located, manufactured
(mobile) home where not prohibited by local
codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certified kit is used.
This appliance is a domestic room-heating
appliance. It must not be used for any other
purposes such as drying clothes, etc.
This appliance is suitable for installation in a
bedroom or bed sitting room.
Massachusetts: The piping and final gas
connection must be performed by a licensed
plumber or gas fitter in the State of Massachusetts.
Ce guide est disponible en français sur demande.
Manufactured by
MILES INDUSTRIES LTD., British Columbia, Canada
www.valorfireplaces.com
4001379-10
©2012, Miles Industries Ltd.
Table of Content
FOR THE OWNER
Remote Control Operation................................. 9
LOR
A
WA R R
NTY
M
GR A
O
PR
T
Owner’s Information .......................................... 5
Warranty Card at the
back of this manual.
OR
Safety and Your Fireplace ................................. 4
VA
Safety Precautions ............................................ 3
CO M F
Options ............................................................ 11
Lighting Instructions......................................... 12
Warranty .......................................................... 28
FOR THE QUALIFIED INSTALLER
Specifications .................................................. 13
Remote Control Preparation ............................ 23
Overview.......................................................... 14
Ceramic Bricks Installation .............................. 24
Dimensions ...................................................... 15
Ceramic Logs Installation ................................ 24
Cavity............................................................... 15
Window Refitting.............................................. 26
Clearances ...................................................... 16
Operation Check & Aeration Settings
Adjustment....................................................... 26
Venting............................................................. 17
Installation Planning ........................................ 18
Existing Fireplace Preparation......................... 18
Appliance Preparation ..................................... 19
Supply Gas Installation .................................... 21
Remote Control Handset Wall Holder
Installation ....................................................... 27
Warranty .......................................................... 28
Spare Parts...................................................... 29
Ignition Spark Check ....................................... 22
The information contained in this installation
manual is believed to be correct at the time of
printing. Miles Industries Ltd. reserves the right
to change or modify any information or specifications without notice. Miles Industries Ltd.
grants no warranty, implied or stated, for the
installation or maintenance of your heater, and
assumes no responsibility for any consequential
damage(s).
Designed and Manufactured by / for
Miles Industries Ltd.
190–2255 Dollarton Highway, North Vancouver, BC, CANADA V7H 3B1
Tel. 604-984-3496 Fax 604-984-0246
www.valorfireplaces.com
© Copyright Miles Industries Ltd., 2012
2
!
Safety Precautions
READ and UNDERSTAND all instructions carefully
before starting the installation. FAILURE TO FOLLOW
these installation instructions may result in possible fire
hazard and will void the warranty.
Prior to the first firing of the fireplace, READ the
Owner’s Information section of this manual.
DO NOT USE this appliance if any part has been under
water. Immediately, CALL a qualified service technician
to inspect the unit and to replace any part of the control
system and any gas control that has been under water.
THIS UNIT IS NOT FOR USE WITH SOLID FUEL.
This unit MUST be used with a vent system as
described in this installation manual. NO OTHER vent
system or components MAY BE USED.
This gas fireplace and vent assembly MUST be vented
directly to the outside and MUST NEVER be attached
to a chimney serving a separate solid fuel burning
appliance. Each gas appliance MUST USE a separate
vent system. Common vent systems are PROHIBITED.
INSPECT the external vent cap on a regular basis to
make sure that no debris, plants, trees, shrubs are
interfering with the air flow.
Installation and repair should be PERFORMED by a
qualified service person. The appliance and venting
system should be INSPECTED before initial use and at
least annually by a professional service person. More
frequent cleaning may be required due to excessive
lint from carpeting, bedding, etc. It is IMPERATIVE that
the unit’s control compartment, burner, and circulating
air passageways BE KEPT CLEAN to provide for
adequate combustion and ventilation air.
The glass door assembly MUST be in place and sealed
before the unit can be placed into safe operation.
Always KEEP the appliance clear and free from
combustible materials, gasoline, and other flammable
vapors and liquids.
DO NOT USE abrasive cleaners on the glass door
assembly. DO NOT ATTEMPT to clean the glass door
when it is hot.
NEVER OBSTRUCT the flow of combustion and
ventilation air. Keep the front of the appliance CLEAR
of all obstacles and materials for servicing and proper
operation.
TURN OFF the gas before servicing this appliance.
It is recommended that a qualified service technician
perform an appliance check-up at the beginning of each
heating season.
Due to the high temperature, the appliance should be
LOCATED out of traffic areas and away from furniture
and draperies. Clothing or flammable material SHOULD
NOT BE PLACED on or near the appliance.
Any safety screen or guard removed for servicing
MUST BE REPLACED prior to operating this appliance.
Clothing or flammable material SHOULD NOT BE
PLACED on or near the appliance.
Children and adults should be ALERTED to the hazards
of high surface temperature and should STAY AWAY to
avoid burns or clothing ignition.
YOUNG CHILDREN should be CAREFULLY
SUPERVISED when they are in the same room as
the appliance. Toddlers, young children and others
may be susceptible to ACCIDENTAL CONTACT
BURNS. A physical barrier is recommended if there
are at risk individuals in the house. To restrict access
to a fireplace or stove, INSTALL AN ADJUSTABLE
SAFETY GATE to keep toddlers, young children and
other at risk individuals out of the room and away from
hot surfaces.
DO NOT OPERATE this appliance with the glass door
removed, cracked, or broken. Replacement of the glass
door should be performed by a licensed or qualified
service person. DO NOT strike or slam the glass door.
The glass door assembly SHALL ONLY be replaced
as a complete unit, as supplied by the fireplace
manufacturer. NO SUBSTITUTE material may be used.
DO NOT place furniture or any other combustible
household objects within 36” of the fireplace front.
BE CAREFUL not to put any decorating objects
sensitive to heat to close above or around the fireplace
as it gets very hot when operating.
DO NOT use this heater as a temporary source of heat
during construction.
This appliance is a DOMESTIC ROOM-HEATING APPLIANCE. It must not be used for any other purposes
such as drying clothes, etc.
State of California. Proposition 65 Warning. Fuels
used in gas, wood-burning or oil fired appliances,
and the products of combustion of such fuels, contain
chemicals known to the State of California to cause
cancer, birth defects and other reproductive harm.
California Health & Safety Code Sec. 25249.6.
3
!
Safety and Your Fireplace
Safety and Your Fireplace
Please Read and Carefully Follow all Safety Warnings and
Operating Instructions Contained in Your Owners Manual
(Replacement Manuals are available by contacting our service department at
1-800-468-2567 or visit www.valorfireplaces.com).
Please Follow These Important
Child Safety Precautions and
Recommendations,
• Parts of your Valor Fireplace become
extremely hot while in operation.
• The glass viewing window
temperature can exceed 500 F
at full capacity.
Momentary contact
with a hot glass
surface can cause
a severe burn,
even if the fireplace
is operating at reduced heating
capacity.
• The glass window will remain hot
for an extended period of time after
the fireplace has been turned off.
Ensure that children are prevented
from touching the fireplace during the
cool down period.
• Toddlers and Young Children
must be closely supervised at all
times when they are in the same
room as the operating fireplace. They
lack full awareness of danger and
rely on your protection. Toddlers, in
particular, do not have the motor skills
and response reflexes to withdraw in
the event of accidental contact with a
4
•
•
•
•
hot surface.
A physical barrier is strongly
recommended if there are young
children, or at-risk individuals in the
house. Install an approved after-market
safety gate to keep toddlers, young
children and other at-risk individuals a
safe distance from the fireplace.
Keep the remote control handset
out of reach of children at all
times. A wall mount storage holster
is provided with your remote control
handset.
Ensure that the fireplace, including
the pilot light, is completely turned
off when children are present and
close supervision and safety barriers
are not available—see page 8 of
Owner’s Information section.
If the fireplace is not going to be used
for the summer or any extended
period of time, remove the batteries
from the remote control handset
and receiver. It is recommended that
batteries are replaced annually in any
event—see page 7.
Owner’s Information
!
WARNING
EXTREMELY HOT!!!
- READ the SAFETY information on pages 3
and 4 of this manual BEFORE operating your
gas heater.
- Some parts of your fireplace are EXTREMELY
HOT, particularly the GLASS window.
- DO NOT LET CHILDREN touch the glass or any
parts of your fireplace even after it is turned off
as it is still hot.
- USE A SAFETY SCREEN or a GATE to reduce
the risk of burns.
- Keep the remote control handset OUT OF
REACH of children.
- HOT HEARTH/FLOOR! The hearth or floor in
front of the fireplace may become very hot when
the fireplace heats. Do not use the hearth as a
seat or shelf.
- Some materials or items, although safe, may
discolor, shrink, warp, crack, peel, and so on
because of the heat produced by the fireplace.
AVOID PLACING candles, paintings, photos,
and other items SENSITIVE TO HEAT within
36 inches (0.9 m) around the fireplace.
- Solid wood flooring in front of the fireplace (if
allowed) may shrink during the heating season
due to heat.
Performance of LPG appliances may be affected by
the quality of commercial gas supplied in your area.
Fireplace
Hearth
Do not put
furniture or other objects
in this space in front of
the fireplace:
36” (0.9 m)
OWNER’S
INFORMATION
Thank You ...
For purchasing a Valor by Miles Industries. Your new
radiant gas heater is a technical appliance that must
be installed by a qualified dealer. Each Valor fireplace
is fully tested during the production process for your
safety and comfort.
Your unit has been professionally installed by:
Dealer Name: ________________________________
Phone Number :_______________________________
Should you encounter an operational problem, call
your dealer immediately.
Do not try to repair the unit as you may cause an
injury or damage the fireplace.
This manual and particularly the preceeding
and following pages contain very important
information regarding the safe operation of your
fireplace as well as maintenance instructions.
Read carefully BEFORE operating your fireplace
and pay special attention to the SAFETY
WARNINGS.
A heating gas appliance does require safe handling
and for this reason, we very strongly recommend that
no children be allowed to touch the fireplace and its
controls at all times. Do install a screen or barrier
in front of the fireplace to protect your children
against severe burns.
Operating Your Fireplace for the First Time
When operating your new fireplace for the first time,
some vapors may be released due to the burning of
curing compounds used in the manufacture of the
appliance. They may cause a slight odor and could
cause the flames to be the full height of the firebox, or
even slightly higher, for the first few hours of operation.
It is also possible that these vapors could set off any
smoke detection alarms in the immediate vicinity.
These vapors are quite normal on new appliances. We
recommend opening a window to vent the room. After
a few hours use, the vapors will have disappeared and
the flames will be at their normal height.
Flame Supervision Device
For your safety, this appliance is fitted with a flame
supervision device which will shut-off the gas supply
if, for any reason, the pilot flame goes out. This device
incorporates a fixed probe, which senses the heat
from the pilot flame. If the probe is cool, the device will
prevent any gas flow unless manually lighting the pilot.
See full lighting instructions on page 12 of this manual.
5
OWNER’S
INFORMATION
Owner’s Information
Cleaning
!
WARNING
DO NOT TOUCH THE GLASS WHILE IT IS HOT!
Let the fireplace cool first before touching it.
Important - Glass cleaning - Mineral deposits
One of the by-products of the combustion process in
a gas appliance is a mineral which can show up as a
white film on the ceramic glass of the viewing door.
The composition of the deposit varies widely from
various locations and also from time to time in the
same location. It seems this is associated with the
varying sulfur content of the gas. You may have the
problem for a time and then not see it for many months
when it will reappear in your area.
We have discussed this problem with ceramic glass
manufacturers and they cannot give us a definitive
answer to this problem. Dealers have tried various
cleaning products with varying results. The following
recommendations will not guarantee results in your
particular case.
NOTE: This is a problem beyond Miles Industries’
control and is not covered under warranty.
• Clean the glass regularly as soon as you notice
the buildup (white film). If the film is left for a longer
period of time, it will bake on. It is then much harder,
if not impossible, to remove.
• NEVER use an abrasive cleaner on the ceramic
glass. Any abrasion of the surface has the
immediate effect of compromising the strength of the
glass. An emulsion type cleaner is recommended.
• Use a soft damp cloth to apply the cleaner. Dry the
glass with a soft, dry, preferably cotton cloth. Most
paper towels and synthetic materials are abrasive to
ceramic glass and should be avoided.
• Our dealers have had good results from the
products listed below. We cannot, however,
guarantee the results of these products.
» BRASSO, POLISH PLUS by KELKEM, COOK TOP CLEAN
CREME by ELCO, WHITE OFF by RUTLAND, TURTLE WAX
Do not clean the glass while it is hot. Always
securely replace the window before lighting. If broken,
the glass pane may only be replaced as a complete
window unit as supplied by the manufacturer.
To remove the window for cleaning:
1. Turn each bolt a quarter turn to disengage the bolt pin.
2. Gently pull
the bottom of
the window
outward and
unhook it from
the firebox’s
opening frame.
3. Set the window
aside in a safe
place to avoid
damage.
To refit the window:
1. Hook its top part to the firebox’s opening frame.
Make sure that the wider part of the window
frame is at the bottom.
2. While you hold the
window, push in
and turn the two top
spring-loaded bolts
a quarter turn to
engage their pin.
3. Push in the bottom of
the window against
Bottom
the firebox and
of window
fasten the two bottom (wider frame)
spring-loaded bolts a
quarter turn.
4. If the Hot Glass Warning plate has been removed
from the front lower corner of the window,
reinstall it by sliding it between the glass and
the frame as indicated.
Hot Glass Warning Plate
6
OWNER’S
INFORMATION
Owner’s Information
Soot or dust can be brushed from the ceramic logs
and firebox walls using a soft brush. Dust can also
be removed from the burner using a soft brush after
removing the ceramic logs. When cleaning, make sure
that no particles are brushed into the slots of the burner.
Checks
A periodic check of the pilot and burner flames should
be made. Check after the fire has been on for at least
30 minutes. The pilot flame must cover the tip of the
thermocouple probe. The main burner flame pattern will
vary from appliance to appliance depending on the type
of installation and climatic conditions.
Remote Control Handset Wall Holder
Your fireplace equipment includes a wall holder to
store the handset. If it hasn’t be installed, refer to the
instructions further on in this manual for the installation.
Batteries
!
WARNING
DO NOT ATTEMPT TO CHANGE THE BATTERIES
WHILE THE FIREPLACE IS STILL HOT! Let the
fireplace cool first before touching it.
CAUTION
DO NOT USE a screwdriver or other metallic object to
remove the batteries from the receiver or the handset!
This could cause a short-circuit to the receiver.
Correct Flame Picture
Pilot Flame can be
seen between logs
Pilot
Flame
The appliance uses four 1.5 V AA alkaline batteries
for its remote control receiver and one 9 V alkaline
battery for its handset. Batteries should last one to two
seasons, depending on usage. Removing the batteries
in the off-season will extend the battery life. Should the
batteries loose power, the control may be operated by
manually turning the control knob at the valve or by
turning off the valve at the switch.
To replace the batteries in the remote control
receiver:
1. The receiver is located to the left of the valve and it
is retained to the firebox by a Velcro tab. Grab the
receiver and pull it out from its location.
2. Slide and remove the receiver cover.
3. Replace the 4 AA batteries.
4. Replace the cover.
5. Put the receiver back in its position pushing it in so it
attaches to the Velcro tab.
Lighting, Operation and Rating Information
!
The appliance area must always be kept clear and
free from combustible materials, gasoline and other
flammable vapors and liquids.
Inspect the vent terminal outdoors regularly to make
sure that snow, trees, bushes, leaves, or other objects
do not obstruct it.
Examine the vent system and terminal regularly. We
recommend annually.
WARNING
DO NOT ATTEMPT TO TOUCH THE DATA PLATE
WHILE THE FIREPLACE IS STILL HOT! Let the
fireplace cool first before touching it.
The Lighting, Operation and Rating information is
located on a plate under the burner. Pull the plate out
out to read it. There is important information on both
sides of the plate.
7
OWNER’S
INFORMATION
Owner’s Information
Servicing
How to Turn Your Fireplace OFF (including pilot)
If any attention is required for your appliance, contact
your supplier quoting the model number. It will be helpful
if the appliance’s serial number can also be quoted. This
number is on the rating plate, which is located under the
burner. The replacement parts are shown at the end of
this manual. Please always quote the part number and
description when requesting spare parts.
First, ensure your fireplace is cooled BEFORE
going ahead.
Locate the gas valve under the firebox.
1. Set the Flame Adjustment Knob clockwise as far
as possible.
2. Push in the Gas Control Knob slightly and turn it
clockwise to OFF. Do not force.
Vent Safety Switch
This appliance is equipped with a vent safety switch
which, when activated, will turn off the burner and
pilot if the vent is blocked, disconnected, or if there is
excessive down draught.
If the safety switch is activated, wait for it to cool off
before trying to light the appliance again. The safety
switch will cool off and reset itself automatically after 25
to 30 minutes.
In the event that the safety switch is activated
again, contact a qualified service technician for
inspection.
Should the safety switch require replacement, only use
parts supplied by Miles Industries.
Flame
Adjustment
Knob
Gas
Control
Knob
Turn gas valve buttons clockwise
to turn fireplace OFF.
How to Ensure Your Fireplace Cannot
Be Turned ON Inadvertently
The best way to ensure your fireplace will not turn on
is to turn it off, including pilot—see above.
If you wish to maintain the pilot only without the main
burner coming on, turn the Gas Control Knob to Pilot
position.
8
Remote Control Operation
OWNER’S
INFORMATION
Your fireplace remote control helps you get the comfort, convenience and aesthetics you want from
your gas fireplace. The remote controls your fireplace in different ways.
IMPORTANT: BEFORE YOU BEGIN, please note that on this system, the settings of time, temperature
and automatic ON/OFF can only be programmed when the function display is flashing. Be patient
when programming as it can take a few seconds to set.
Setting the time
The first thing to do is to set the time.
1. With your thumb, hold down both the AUTO and TIMER buttons until F
flashes. Let go.
2. Note the digital clock on the bottom right hand corner. The ▲ button sets
the hour; the ▼ button sets the minutes. Set the time.
Note: You must start setting the time while the F is flashing. If it stops
flashing, go back to 1.
3. The display shows °C/24-hour or °F/12-hour. To change the temperature/
hour display, press on the AUTO button while the display flashes.
4. Let go and wait until the flashing stops. The remote shows the time you
set. It also shows the current temperature.
Setting the temperature
Use this setting when you come in and want to enjoy a specific temperature.
1. Push the AUTO button until a number and F flash. Let go.
2. While it is still flashing, push the ▲ and ▼ buttons to the temperature
you want. Let go.
Your fireplace will reach that temperature and the remote will check the
temperature every five minutes, adjusting the amount of fuel needed to give
you a steady, even heat.
9
OWNER’S
INFORMATION
Remote Control Operation
Setting the flame
Use this setting when you want a particular flame level. For instance, you want
to watch flames burn at their highest level and you don’t mind if the room is too
hot.
1. To raise the flame, press and hold the ▲ button until the flame gets to the
desired level. Let go.
2. To lower the flame, press and hold the ▼ button until the flame gets to
the desired level. Let go.
The flame level will remain just as you set it.
Automatic ON/OFF
You can set your fireplace to come on before you wake up and turn off after
you leave and then, turn on again just before you come home and turn off
after going to bed.
You can leave it like this for the heating season.
1. Decide what temperature you want your fireplace to be at. Also, decide
what time you want your fireplace to turn on and off. Finally, decide what
time you want it to come back on and off in the afternoon or evening. For
the first few times you set the timer, it’s handy to write these times down.
2. Set the temperature (just as you did in the section Setting the
temperature.)
3. Press the TIMER button and hold it until P1 ☼ appears and flashes. Let
go. While flashing, push the buttons ▲ (hour) and ▼ (minutes) to set the
time at which you want your fireplace to turn on in the morning.
4. Press the TIMER button and hold it until P1 ☽ appears and flashes. Let
go. While flashing, push the buttons ▲ (hour) and ▼ (minutes) to set the
time at which you want your fireplace to turn off when you leave.
5. Press the TIMER button and hold it until P2 ☼ appears and flashes. Let
go. While flashing, push the buttons ▲ (hour) and ▼ (minutes) to set the
time at which you want your fireplace will turn on again in the afternoon.
6. Press the TIMER button and hold it until P2 ☽ appears and flashes. Let
go. While flashing, push the buttons ▲ (hour) and ▼ (minutes) to set the
time at which you want your fireplace to turn off in the evening.
Note: If you want to set your fireplace for only one time on and off, set P2 ☼
and P2 ☽ for the same times as P1 ☽. The remote will record the P1 ☽ off
time for both P2 times.
To temporarily override the timer setting, just press AUTO or ▲ and ▼ to go
back to manual settings. Press TIMER to go back to your settings.
When your remote control displays BATT, you need to replace the battery
with a new 9 volt alkaline battery—6LR61/MN1604.
CAUTION
DO NOT USE a screwdriver or other metallic object to
remove the batteries from the receiver or the handset!
This could cause a short-circuit to the receiver.
10
Options
OWNER’S
INFORMATION
Venting (required)
Hearth Gate (optional)
Approved venting accessories as per local codes.
Hearth gates such as Cardinal’s VersaGates are
available at retail stores carrying safety products
for children.
Inner Front (required)
See your dealer for your choice of Inner Fronts.
Outer Surrounds, Trims & Frets (optional)
See your dealer for your choice of Outer Surrounds
and Trims and Frets.
Optional Accessories
770ZCK—Zero Clearance Kit
759EBL—Enamel Liner
754RSK—Rock Set Kit
760CBL—Ceramic Black Liners (fluted)
Conversion Kit (optional)
738PGK—Conversion Kit to Propane Gas
738NGK—Conversion Kit to Natural Gas
11
OWNER’S
INFORMATION
Lighting Instructions
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.
A. This appliance has a pilot, which must be lighted by hand. When lighting the pilot, follow these
instructions exactly. To save energy, turn the pilot off when not using the appliance.
B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Do not touch any electric switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s
instructions.

If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the control knobs. Never use tools. If the controls will not
push in or turn by hand, don’t try to repair them, call a qualified service technician. Force or
attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water. Immediately call a qualified service
technician to inspect the appliance and to replace any part of the control system and any gas
control, which has been under water.
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above.
2. Set the flame adjustment knob as far
clockwise
as possible*.
3. Turn the gas control knob clockwise
to OFF.
NOTE: The knob cannot be turned from PILOT to
OFF unless it is pushed in partially. Do not force.
4. Wait five (5) minutes to clear out any gas, then
smell for gas, including near the floor. If you
smell gas, STOP! Follow “B” in the safety
information above. If you don’t smell gas, go to
the next step.
5. Find the pilot. It is at the left side of the firebox
viewed through slotted hole in front log.
6. Push in and turn the gas control knob counterclockwise until resistance is felt just before the
“IGN” position.
7. Keep pushed in for a few seconds to allow gas to flow then, keeping knob depressed, turn to
“PILOT” to light pilot. Hold knob in for a further 5 seconds then release. The knob should pop
back out. Pilot should remain lit. If pilot goes out repeat steps 3 through 7.
 If knob does not pop out when released, stop and immediately call your service technician or
gas supplier.
 If pilot lights but will not stay lit after several tries, turn the gas control knob to “OFF” and call
your service technician or gas supplier.
8. When pilot is lit, partially depress the knob and turn to “ON” position (Burner alight).
 Do not leave knob set between “PILOT” and “ON”.
9. Set the flame height to desired setting*.
TO TURN OFF GAS TO APPLIANCE
1. Set the flame adjustment knob as far clockwise
as possible*
2. Push in gas control knob slightly and turn clockwise
to “OFF”. Do not force.
* The flame height can be increased or decreased by depressing the remote control hand set
button.
12
OWNER’S
INFORMATION
Specifications
Approval & Codes
*High Altitude Installations
This appliance is certified to ANSI Z21.88-2009 / CSA
2.33-2009 American National Standard / CSA Standard
for Vented Gas Fireplace Heaters for use in Canada
and USA, and to CGA 2.17-91 High Altitude Standard
in Canada. This appliance is for gravity vent insert
installations.
Input ratings are shown in BTU per hour and are
certified without deration for elevations up to 4,500 feet
(1,370 m) above sea level.
For elevations above 4,500 feet (1,370 m) in USA,
installations must be in accordance with the current
ANSI Z223.1 and/or local codes having jurisdiction.
Heating value of gas in some areas is reduced to
compensate for elevation—consult your local gas utility
to confirm.
For installations at elevations above 4,500 feet (1,370
m) in Canada, please consult provincial and/or local
authorities having jurisdiction.
This appliance complies with CSA P4.1-09 Testing
method for measuring annual fireplace efficiencies.
The installation must conform to local codes or, in the
absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1 or the Natural Gas and Propane
Installation Code CAN/CGA-B149. Only qualified
licensed or trained personnel should install this
appliance.
This appliance must be electrically grounded in
accordance with local codes, or, in the absence of local
codes, with the National Electrical Code, ANSI/NFPA
70 or the Canadian Electrical Code, CSA C22.1.
Ratings
Model
Gas
Altitude (Ft.)*
Input Maximum (Btu/h)
Input Minimum (Btu/h)
Manifold Pressure (in
w.c.)
Minimum Supply
Pressure (in w.c.)
Maximum Supply
Pressure (in w.c.)
Main Burner Injector
Marking
Pilot Injector Marking
Min. Rate By-Pass Screw
NG
LPG
Natural
Propane
0-4,500 feet*
24,000
24,000
6,500
13,000
3.95
9.5
Supply Gas
Heater engine 738BXN is used with natural gas.
Heater engine 738BXP is used with propane gas.
The supply pressure must be between the limits shown
in the Ratings section above.
The supply connection is 3/8” NPT female and located
on the left hand side of the control valve. The gas line
entry point is on the left hand side on the fireplace.
X
X
11.0
Conversion Kits
10.5
14.0
82-650
92-260
The 738BX Legend G3 is supplied as natural gas or
propane gas and is field convertible between fuels. See
instructions packaged with the conversion kit for further
information.
35
125
27
125
5.0
Electrical
The 738 does not require an electrical power source to
operate as a heater.
13
QUALIFIED
INSTALLER
Overview
This appliance, as supplied, may ONLY be installed in an existing
unaltered, functioning solid-fuel burning fireplace with a working flue and
constructed of non-combustible material.
This appliance is APPROVED for installation into combustible type
construction only when using the 770ZCK Zero Clearance Kit (see
separate instructions packaged with the kit for details).
! WARNING
Some materials or items, although
safe, may discolor, shrink, warp,
crack, peel, and so on because of
the heat produced by the fireplace.
Avoid placing candles, paintings,
photos, and other items sensitive to
heat around the fireplace.
! WARNING
HOT HEARTH / FLOOR! The
hearth or floor in front of the fireplace may become very hot when
the fireplace heats. Do not use the
hearth as a seat or shelf. Solid wood
flooring in front of the fireplace (if
allowed) may shrink during the heating season due to heat.
Chimney Terminal Cap
Flashing
Approved 3” flex
chimney liner
running full length
Outer trim
(optional, sold
separately)
Existing unaltered,
functioning solidfuel burning
fireplace & chimney
Inner Front
(required, sold
separately)
Fret
(optional, sold
separately)
738BX fireplace
14
QUALIFIED
INSTALLER
Dimensions
28-5/8” (727 mm)
19-1/2” (495 mm)
12” (305 mm)
or 12-5/8” (321 mm)
Varies with
outer trim options
Optional Outer Trim or
Surround sold separately
7-7/8” (200 mm)
or 8-1/2” (216 mm)
Varies with
outer trim options
20”
(508 mm)
Gas inlet
Gas connection
Cavity
Check that masonry step does not interfere with install dimensions or
vent pipe.
If mantel is combustible, see section Clearances for allowable
clearances.
Minimum width of fireplace opening at front: 28” (711 mm)
X
Y
X = 12” (305 mm) or 12-5/8” (321 mm)—varies with outer trim options
Y = 20” (508 mm)
15
QUALIFIED
INSTALLER
Clearances
! WARNING
Some materials or items, although safe, may discolor, shrink, warp, crack, peel,
and so on because of the heat produced by the fireplace. Avoid placing candles,
paintings, photos, and other items sensitive to heat around the fireplace.
Combustible Mantel Clearances
A
Mantel
Projection A
1”
(25 mm)
4”
(101 mm)
8”
(203 mm)
14”
(355 mm)
Mantel
Height B*
28”
(711 mm)
32”
(813 mm)
35”
(889 mm)
38”
(965 mm)
*Measure taken from the underside of the mantel to finished
hearth or surface that the unit is sitting on.
Do not put
furniture or
objects within
36” (914 mm)
of the front of
appliance
Finishing Materials
B
Combustible materials: Material such as wood,
compressed paper, plant fibers, plastics or any material
capable of igniting and burning, whether flame-proofed
or not, plastered or un-plastered.
Non-combustible materials: Material such as steel,
iron brick, tile, concrete or materials that bear the UL
mark for zero (0) fire rating.
! WARNING
HOT HEARTH / FLOOR! The hearth or floor in
! WARNING
HOT GLASS! The use of a screen in front of
the glass is highly recommended particularly in
households with children.
front of the fireplace may become very hot when
the fireplace heats. Do not use the hearth as a seat
or shelf. Solid wood flooring in front of the fireplace
(if allowed) may shrink during the heating season
due to heat.
Sidewall Clearances
sidewall
9” (229 mm)
16
Minimum distance from side of appliance (liner box) to
combustible wall: 9” (229 mm).
QUALIFIED
INSTALLER
Venting
Vent Location
Typical Vent Installation
The vent terminal must be located through the roof. This gravity
vent appliance is designed to opreate when an undistrubed
airflow hits the outside vent terminal from any direction.
Check local codes for allowable vertical vent termination.
Terminal Cap
Flashing
Vent Materials
Use a 3” diameter aluminum flex liner approved for gas
venting when installed as an insert (existing chimney). Use a
4” diameter type “B” vent when installed with a 770ZCK Zero
Clearance Kit (see separate instructions packaged with the kit
for details).
1 x 3” flex liner
Venting Notes
Where possible, avoid joining flex pipe. If joints are required,
use a approved connector and seal joints with RTV high temp
sealant.
Horizontal offsets are permissible to allow for routing around
masonry projections. Avoid bending flex pipe over a 45 degrees
radius where possible.
Min. 8 feet (without offset)
Min. 10 feet (with offset)
Approved Termination Required
Minimum vent lengths.
For other allowable configurations,
refer to the venting tables in the
National Fuel Gas Code Z223.1 or the
Natural Gas or Propane Installation
Code B149.1.
Max. 36” offset at 10’-0” min. vertical
3” Liner
3” min. Bend
Radius
Minimum Vent Liner Radius
Allowable Vent Configurations
17
QUALIFIED
INSTALLER
Installation Planning
Only qualified licensed or trained personnel
should install this appliance.
Installer—READ THIS FIRST
1. YOU NEED TO KNOW FROM THE
HOMEOWNER what accessories (surround,
door, etc.) will be installed with this fireplace;
2. Unpack the appliance.
3. Check that you have everything.
4. Clean cavity, chimney, ash dumps, clean-outs.
5. Install venting pipe.
6. Attach conversion plate to existing fireplace.
7. Fit appliance into cavity.
8. Connect and test gas supply.
9.
10.
11.
12.
13.
14.
Install the remote control system.
Install bricks and logs.
Refit window.
Verify operation and adjust aeration settings.
Install the remote control handset wall holder.
Instruct the homeowner on the operation and
maintenance of the fireplace.
15. Install the surround trim and front.
16. Install the fret if required.
Existing Fireplace Preparation
A few points must be considered before inserting the
738BX into an existing fireplace cavity. Generally, no
modifications are allowed to the existing fireplace that
will compromise the integrity of the existing fireplace.
Components that are bolted or screwed on such as
dampers or baffles may be removed to accommodate
the installation of the 738BX engine. Cutting away
any sheet metal parts of the existing fireplace
to accommodate the installation of the 738BX is
prohibited. Check with local authorities if in doubt.
Clean Fireplace and Chimney
Have the chimney swept and the fireplace cavity
including ash dumps and clean-outs cleaned before
installing the 738BX heater and vent liners. Any
creosote or soot residue remaining in the fireplace
cavity chimney or clean-out may cause odors or
stains once the 738BX insert is installed. Consult with
chimney sweep for information on how best to clean.
Existing Dampers
Factory-built, zero-clearance fireplaces will require the
damper to be removed in order to install the vent liners.
These dampers are usually bolted into place. Dampers
in masonry fireplaces must be fixed open and may
remain in place.
18
Ash Retaining Curbs
Some fireplaces (particularly factory-built) have a
raised curb at the front edge to retain ashes. Check the
dimensions carefully to ensure the 738BX engine will fit
behind any raised curb (some curbs may be removed
separately from the refractory base).
Gas Line Routing
Plan the routing of the gas line before proceeding.
Use the existing hole for the gas line in factory-built
fireplaces. If the fireplace has no access hole, carefully
drill an access hole of 1.5 inch (38 mm) or less through
the lower sides or bottom of the firebox. The access hole
must be plugged with non-combustible insulation after
the gas supply line has been installed. See Dimensions
section for detailed location of gas inlet. Also, take
into consideration whether or not a shut-off valve will
interfere when planning routing of the gas line.
Existing Fireplace Preparation
Existing Glass Doors and Wire Screens
Existing glass doors must be permanently removed
prior to installing the 738BX insert.
Combustible Mantels
Combustible mantel clearances must conform to those
required for the original solid-fuel fireplace into which
the 738BX is being installed.
QUALIFIED
INSTALLER
Attach Warning Conversion Plate to Existing
Fireplace (label supplied loose with 738BX
heater)
Attach the “This fireplace has been converted...”
label to the existing fireplace using screws or other
mechanical means and store any removed parts in
back of the existing fireplace for future use.
Appliance Preparation
Unpacking the appliance
Beware of sharp edges! Wear gloves!
1. Unpack the appliance.
2. Unpack any loose items from around the appliance
and check against the Pack Content list provided in
the documentation package.
3. Remove the window and set aside in a safe place to
avoid damage.
4. Verify that you have all the components required
for the installation, including:
- brick panels & logs;
- surround/doors/fret;
- venting components and accessories.
Window Removal
The window is held in place by four spring-loaded bolts,
two at the top and two at the bottom.
1. To remove the window, turn each bolt a quarter turn
to disengage the bolt pin.
2. Gently pull the bottom of the window outward and
unhook it from the firebox’s opening frame.
3. Set the window aside in a safe place to avoid
damage.
19
QUALIFIED
INSTALLER
Appliance Preparation
Venting Installation
IMPORTANT: This appliance’s venting system requires room air to be used
in the combustion process.
1. Rough-in one 3” diameter vent liner into the existing chimney
system from the roof. Be careful not to tear or damage the liner
in the process. Leave plenty of liner at the bottom to facilitate the
connection of the liner to the vent slider. It is best to leave the top
termination until later.
2. a) Large cavity opening
Slide the appliance into the cavity.
b) Smaller cavity opening
Release the two screws retaining the vent slider to the front of the
firebox.
Remove the slider from the firebox by sliding it towards the back of
the firebox.
3. Secure the liner to the collar on the vent slider using 4 tapping
screws.
If the vent slider was removed from the firebox, slide the firebox
onto the vent slider in the cavity taking care not to damage the liner.
Make sure that the vent slider is pulled all the way forward.
Secure the vent slider to the front of the firebox with two screws
removed earlier.
4. From the roof, pull the liner and fit the flashing.
5. Fit the terminal cap. Secure with screws.
6. Seal the terminal and flashing from water penetration as required.
5
6
4
1
option 2b
3
! WARNING
Failure to position the parts in
accordance with these diagrams or
failure to use only parts specifically
approved with this appliance
may result in property damage or
personal injury.
20
option 2a
QUALIFIED
INSTALLER
Supply Gas Installation
The gas supply inlet connection is a 3/8” NPT female
connector and is located on the left hand side of the
control valve.
Pressure Test Points
The minimum supply pressure is given in the section
Specifications of this manual—page 13.
All piping and connections must be tested for leaks
after installation or servicing. All leaks must be
corrected immediately.
When testing for leaks:
X
Use only new black iron or steel pipes or copper tubing
if acceptable—check local codes. Note that in USA,
copper tubing must be internally tinned for protection
against sulfur compounds.
The burner platform and gas train on this appliance
may be removed as a unit for servicing or to install or
remove the optional circulating fan (if installed). Provide
some form of pipe union (depending on type of piping)
as close as possible to appliance valve.
Unions in gas lines should be of ground joint type.
The gas supply line must be sized and installed to
provide a supply of gas sufficient to meet the maximum
demand of the appliance without undue loss of
pressure.
• Make sure that the appliance is turned off.
• Open the manual shut-off valve.
• Test for leaks by applying a liquid detergent or soap
solution to all joints. Bubbles forming indicate a gas
leak.
Never use an open flame to check for leaks.
Correct any leak detected immediately.
The pressure test tapping locations are shown in the
figure below. An internal regulator within the valve
controls the burner manifold pressure. The correct
pressure range is shown in the table in section
Specifications of this manual on page 13. The pressure
check should be made with the burner alight and at its
highest setting. See Lighting Instructions section for full
operating details on page 12.
Sealant used must be resistant to the action of all
gas constituents including LP gas. Sealant should be
applied lightly to male threads to ensure excess sealant
does not enter gas lines.
Pressure test the supply line for leaks.
The appliance and its individual shut-off valve must be
disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in
excess of 1/2 psig (3.5 kPa).
The appliance must be isolated from the gas supply
piping system by closing its equipment shut-off valve
during any pressure testing of the gas supply piping
system at test pressures equal to or less than 1/2 psi
(3.5 kPa).
Failure to either disconnect or isolate the appliance
during pressure testing may resulting regulator or valve
damages and void the warranty. Consult your dealer in
case of damages.
Manifold
pressure
test tapping
Supply
pressure
test tapping
Pressure Testing
21
QUALIFIED
INSTALLER
Ignition Spark Check
The pilot burner and electrode unit are at the left end of the burner.
Push in the lighting knob and turn it counter-clockwise through the “IGN” position to “PILOT”. A spark should flash
across from the pilot electrode to the pilot burner shield as shown below.
Thermostat Knob
22
Gas Control Knob
QUALIFIED
INSTALLER
Remote Control Preparation
CAUTION
CAUTION
DO NOT PUT BATTERIES IN THE REMOTE
CONTROL RECEIVER until the wires are connected to the burner control unit as shortcircuit could result in the destruction of the
electrical components.
1. Connect the wiring harness to the receiver box,
by pushing the wire connector on to the receiver
circuit board. The plug will only go on one way so
please ensure that the wires are pointing up and the
slot in the board is in line with the tab on the wiring
harness plug.
2. Connect the wires as shown. Please note that
the “L” connectors are different sizes; the smaller
one fits to the lower connection and the larger one
the top connection on the top left hand side of the
valve. The other two wire connectors can be fitted to
either terminal located to the left of the flame control
button.
3. Remove the remote control receiver lid.
4. Fit four AA 1.5 V alkaline batteries. Refit the lid.
5. Place the remote control receiver on the base of the
fireplace beside the valve.
6. Fit the 9 V alkaline battery to the handset
transmitter.
DO NOT USE a screwdriver or other metallic object to
remove the batteries from the receiver or the handset!
This could cause a short-circuit to the receiver.
Remote control operating instructions are on
pages 9–10 of this manual and are supplied with
the remote control kit.
Remote control
receiver
Push-on
Connector
Push-on Connector
Receiver
Receiver
GV34 Valve
GV34 Valve
23
QUALIFIED
INSTALLER
Ceramic Bricks installation
The following guidelines apply for all brick liners.
1. Inside the firebox, on the top of each side, release
the screw of the side brick anchors (one per side)
just enough to allow them to rotate.
4. Rotate the anchor up and out of the way and slide
the right hand side panel against the firebox side.
Rotate the anchor back down to hold the panel.
2. Place the rear panel against the back of the firebox,
on the ledge at bottom.
5. Tighten the side brick anchors on each side of the
firebox.
3. Rotate the anchor up and out of the way and slide
the left hand side panel against the firebox side.
Rotate the anchor back down to hold the panel.
6. Install the port cover fixing it using the two screws
already in the firebox top.
Ceramic Logs Installation
Unpack he ceramic logs very carefully to avoid damaging the fragile material. Install the logs as shown below.
Please note that the position of the Logs is critical to insure proper performance of the appliance.
1. Spread the decorative charcoals on each side of
the log tray, covering the sheet metal as shown.
DO NOT PUT ANY DECORATIVE CHARCOAL
PIECES WITHIN THE PILOT
SHIELD AREA.
24
Ceramic Logs Installation
2. Place the rear log centering it side to side in the
firebox. Position forward until it sits against the
sheet metal return behind the burner.
Rear Log
against
Sheet Metal
Return
QUALIFIED
INSTALLER
5. Identify the right cross log; it has
a hole under on of its end and it is
the shortest cross log. Place it on
the right pin located on the rear
log. Rest its other end in the crook
of the front right log.
6. Identify the middle cross log. It does not have a
hole underneath. Place its narrow end on the flat
depression in the rear log next to the right cross log
on the rear log. Place its wider end on the front log.
3. Place the front left log on top of the burner with its
front edge resting slightly on the window frame.
4. Place the front right log on the top of the burner
with its left end abutted to the front left log and its
front edge resting slightly on the window frame.
Center the front logs side to side in relation to
the firebox.
7. Identify the left cross log; it has a hole under its
narrow end. Place its narrow end on the pin located
on the rear log. Rest its wider
end on the the crook in the
front left log at an angle of
approximately 30 degrees
from the center line of the
fireplace to allow for the
flame to come up in front of
the rear log.
Both front logs to rest slightly on the
edge of the firebox window frame.
25
QUALIFIED
INSTALLER
Window Refitting
1. To refit the window, hook its top part to the firebox’s
opening frame. Make sure that the wider part of
the window frame is at the bottom.
2. While you hold it, push in and turn the two top springloaded bolts a quarter turn to engage their pin.
3. Push in the bottom of the window against the firebox
and fasten the two bottom spring-loaded bolts a
quarter turn.
4. If the Hot Glass Warning plate has been removed
from the front lower corner of the window,
reinstall it by sliding it between the glass and
the frame as indicated.
Bottom
of window
(wider frame)
Hot Glass Warning Plate
Operation Check & Aeration Settings Adjustment
Operation Check
Turn the fireplace flame up and down using the
remote control to confirm that the full range of inputs
is achieved—see the remote control operation
instructions on pages 9–10.
Aeration Settings
Light the fire and allow the unit to warm up for 10–15
minutes to evaluate the flame picture. Burners are
equipped with an adjustable shutter to control primary
aeration. See the figures below. The shutters are
factory-set to an aeration gap which will give optimum
performance for the vast majority of installations.
In a few unusual installations, the flame picture may
be improved by adjusting the aeration. The need for
adjustment should be determined only by operating the
appliance with the ceramic logs and window installed.
Increasing aeration (open) will cause the flames
to appear more transparent and blue showing more
ceramic log glow.
Decreasing aeration (close) will cause the flames to
appear more yellow or orange showing less ceramic
log glow.
Too little aeration may result in black carbon
forming and dropping into the firebox.
Air Shutters
NG
LPG
Close
Flashback
shield (for
LPG only)
Open
NG Air Shutter
Slider & Cover
26
Close
Open
LPG Air Shutter
Slider
Close
Open
Remote Control Handset Wall Holder Installation
QUALIFIED
INSTALLER
The remote control kit for this fireplace
Alternative 2
Alternative 3
Packing Contents:
comes complete with a wall-mounted holder.
1 Wall Bracket A
This holder is not required in all installations
2 Screws B
but is provided as an optional feature for
1 Screw C
those customers who wish to mount the
2 Wall Anchor D
remote handset to the wall.
1 Spacer E
(detach before assembly)
To install the holder to the wall, find a
Switch Plate
convenient location and use the hardware
1 Wall Bracket F
provided with the kit. See the diagram below
Alternative 1
for required hardware and configurations.
Note that the holder can be installed at the
base of a light switch plate.
IMPORTANT. The location of the remote
control handset is important to assure proper
temperature regulation. To obtain a constant
temperature, we recommend that the handset should be between 3 and 15 feet away from the appliance but not
directly above it. We also advise that the handset should be located away from any other heat source and not in
direct sunlight as this may affect the temperature sensor located in the remote handset.
27
OWNER’S
INFORMATION
WA
TY
N
A
RR
M
GR A
O
PR
T
LOR
OR
If you have a problem with this unit, please contact your dealer or supplier
immediately. Under no circumstances should you attempt to service the unit
in any way by yourself. The warranties in paragraphs 1 and 2 are provided
only to the first purchaser/user of this unit, are not transferable and are
subject to the conditions and limitations in paragraphs 3, 4 and 5. Please
review the conditions and limitations carefully and strictly follow their
requirements.
VA
Warranty
CO M F
1. Extended Warranty Coverage
For a period of up to ten (10) years, Miles Industries Ltd., (the “Company”) or its appointed distributor will at its option pay the
initial purchaser for the repair of, or will exchange the following parts or components which are found to be defective in material or
workmanship under normal conditions of use and service:
Part or Component
Defect Covered
Maximum Warranty Period
Exterior steel casing
Corrosion
10 years
Glass
Loss of structural integrity
10 years
Cast iron parts
Corrosion
10 years
Firebox and heat exchanger
Corrosion (but not discoloration) causing
loss of structural integrity
10 years
2. Two-Year Parts Warranty
In addition, for two (2) years from the date of purchase, the Company, at its option, can repair or exchange all parts and components
not listed above but that are found to have a bona fide defect in material or workmanship under normal conditions of use.
3. Conditions and Limitations
a) The warranty registration card must be completed by the initial owner and returned to the Company within 90 days of purchase.
b) Installation and maintenance must be performed by an authorized and trained dealer in accordance with the Company’s installation
instructions.
c) This warranty is void where installation of the unit does not conform to all applicable codes including national and local gas
appliance installation codes and building and fire codes.
d) The owner must comply with all operating instructions.
e) The Company is not responsible for the labor costs to remove defective parts or re-install repaired or replacement parts.
f) The first purchaser or user of the unit will be responsible for any shipping charges for replacement parts as well as travel time
incurred by the dealer to perform the warranty work.
g) This warranty applies to non-commercial use and service and is void if it is apparent that there is abuse, misuse, alteration,
improper installation, accident or lack of maintenance to the unit.
h) This warranty does not cover damage to the unit through:
i)
Improper installation, operational or environmental conditions.
ii) Inadequate ventilation in the area or competition for air from other household equipment or appliances.
iii) Damage due to chemicals, dampness, condensation, or sulphur in the fuel supply lines which exceeds industry standards.
i) This warranty does not cover glass, log breakage or damage to the unit while in transit.
j) The Company does not allow anyone to extend, alter or modify this warranty and assumes no responsibility for direct, indirect or
consequential damages caused by the unit. State or provincial laws where the first purchaser or user resides may provide specific
rights to extend this warranty and, if so, the Company’s sole obligation under this warranty is to provide labor and/or materials in
accordance with those laws.
4. Discharge of Liability
After two (2) years from the date of purchase, the Company may, at its option, fully discharge all obligations under this warranty by
paying to the first purchaser/user the wholesale price of any defective parts.
5. No Other Warranty
All obligations to repair this unit are defined in this warranty. Some states or provinces may specifically mandate additional warranties
on the part of manufacturers, but in the absence of such specific legislation, there is no other warranty or obligation expressed or
implied.
28
OWNER’S
INFORMATION
Spare Parts
Description
Part
Number
Code
Description
Part
Number
1
Exhaust Slide Assembly
4000127
31
Warning Hot Glass Plate
4003093
2
Port Cover
4001820AH
32
Thermocurrent Interruptor
4000202
3
4
Log Support
4001841
35a
GV34 Valve Assembly NG
4003096
Side Bricks Anchors (2)
4001283
35b
GV34 Valve Assembly LPG
4003109
5
Top Mounting Bracket
4000136AZ
36
Remote Control Thermostatic
4000099
6
Side Mounting Brackets (2)
4000135AZ
37
Remote Control Handset
4000327
7
Window Assembly
4001378
38
Handset Wall Holder
9000008
Burner Assembly NG
4001180
39
Receiver
4000328
Burner Assembly LPG
4001181
40
Wiring Harness
4000329
Burner Rail NG
4001665
41
Log Set Complete
4001696
Burner Rail LPG
4001666
42
Rear Log
4001697
Injector Elbow (Main Burner) NG
9730012
43
Front Left Log
4001699
Injector Elbow (Main Burner) LPG
9730007
44
Front Right Log
4001700
Code
8
9
10
11
Air Shutter Cover NG
4002346
45
Right Cross Log
4001701
11a
Air Shutter Slider NG
4002345
46
Middle Cross Log
4001698
12
Flashback Shield LPG
3000371
47
Left Cross Log
4001772
12a
Air Shutter Slider LPG
320B293
48
Loose Coals
4001843
13
Burner Baffle
4001784
49
Brick Set Complete
4001515
14
Burner Mounts (2)
4001678
50
Rear Brick Panel
4001811
15
Pilot Shield
4000144
51
Left Brick Panel
4001809
Pilot Assembly NG
4000062S
52
Right Brick Panel
4001810
Pilot Assembly LPG
4000063S
53
Vent Switch Assembly
4000204
Pilot Bracket
720A542
Pilot Injector NG—No 35
4002511
16
17
18
Pilot Injector LPG—No 27
720A195
19
Hooked Olive for Pilot Injector
720A196
20
Olive Nut for Pilot Pipe
420K385
21
Electrode
720A543
22
Electrode Retaining Nut
720A200
23
Thermocouple
4000061
24
Pilot Mount
4000138
25
Pipe—Valve to Main Burner (incl.
olive & nuts)
4000065
26
Burner Tray
4001677
27
Burner Plate Access Panel
4001681
28
Olive Nut for Pilot Pipe
220K913
29
Pipe—Valve to Pilot
4001838
30
Valve Mounting Bracket
4000141
29
OWNER’S
INFORMATION
Spare Parts
41
42
1
44
43
47
45
46
2
48
4
5
7
3
6
NG
LPG
9
LPG
12
NG
11
31
11a
13
12a
10
49
15
14
50
17
21
22
16
18
19
20
24
25
26
23
51
52
27
37
29
36
28
38
30
35a, 35b
40
39
53
30
32
Thank You ...
For purchasing a Valor by Miles Industries. Your new radiant gas
heater is a technical appliance that must be installed by a qualified
installer.
Please fill in the information below. The information provided will be
used for customer records only.
Fireplace Information
Model Number: 738B
XN or
XP
Serial Number:
Date Purchase (yyyy-mm-dd):
Dealer:
Customer Information
First Name:
Last Name:
Contact Information
Email:
Mailing Address
Address:
City:
Province/State:
Postal/Zip Code:
Country:
Cut out page, fill information, and mail to Miles Industries Ltd.
Online Warranty registration at www.valorfireplaces.com
Tape Shut
Fold here
Postage
needed
Miles Industries Ltd.
190 - 2255 Dollarton Highway
North Vancouver, BC V7H 3B1
Canada
Online Warranty registration at www.valorfireplaces.com
Thank you for choosing a Valor Product