Siemens Gigaset 3000 Operating instructions

Operation
HiPath 3000/HiPath500
Gigaset SL3 professional in HiPath Cordless Office
www.siemens.de/enterprise
Safety notes
Safety notes
Handset
Danger:
•
•
•
•
Do not use the handset in potentially explosive atmospheres.
To avoid mutual interference, do not operate the handset in the
vicinity of electronic equipment.
Do not use the handset in wet rooms! Devices are not splashproof.
A transmitter signal is emitted by your handset. Please observe
safety procedures for your area.
Note:
The ringing tone, signal tones and handsfree talking (speakerphone
mode) are played over the loudspeaker. Do not hold the telephone
to your ear when it is ringing or if speakerphone mode is switched
on. Otherwise you may seriously impair your hearing.
Note:
•
•
Information for hearing aid users: Radio signals can interfere in
hearing aids.
Please provide the operating instructions with the handset if giving it to another user.
Battery pack
Danger:
•
•
•
•
II
Only use the original rechargeable battery pack recommended
by Siemens.
Do not use a standard rechargeable battery pack. This can result
in serious injury and material damage (risk of explosion, degradation of battery pack cladding, functional interference and
handset damage).
Avoid contact with fire and water.
Only use the approved C39280-Z4-C373 power supply unit to
operate the charging shell.
Safety notes
WEEE mark
Note:
•
•
•
•
All electrical and electronic products should be
disposed of separately from the municipal waste
stream via designated collection facilities appointed by the government or the local authorities.
The correct disposal and separate collection of
your old appliance will help prevent potential negative consequences for the environment and human health. It is a precondition for reuse and recycling of used electrical and electronic
equipment.
For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service, the
shop where you purchased the product or your sales representative.
The statements quoted above are only fully valid for equipment
which is installed and sold in the countries of the European Union and is covered by the directive 2002/96/EC. Countries outside the European Union may have other regulations regarding
the disposal of electrical and electronic equipment.
III
Overview of handset
Overview of handset
1
2
3
4
5
15
6
14
13
7
12
8
9
11
10
1
Receiver inset
10
Jack for headset, PC interface and
charging unit
2
Display
11
Call-by-call key
3
Display keys
12
Hash key
4
Control key
13
Number keys
5
Speakerphone key
14
On-hook and on/off key
6
Talk key
15
Message key
7
Star key
8
R key
9
Microphone
How to use the keys: Æ Page 11
IV
Contents
Contents
Overview of handset . . . . . . . . . . . . . . . . . . . . . . . . . . IV
Operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . 1
Conducting calls –
the basic functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Activating/deactivating the handset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
First seize the line, then dial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Dial first, then seize the line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Manual number redial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Callback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Enquiry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Answering or rejecting a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Picking up a call in a call pickup group. . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Ending a call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Forwarding calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Activating or deactivating the keypad lock . . . . . . . . . . . . . . . . . . . . . . 10
After leaving the radio network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Description of controls . . . . . . . . . . . . . . . . . . . . . . . . 11
Function keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
R key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Menu icons in the main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
12
12
13
15
Putting the handset into service . . . . . . . . . . . . . . . . 16
Removing the protective cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inserting the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Charging and using the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery pack operating times and charging times . . . . . . . . . . . . . . . .
Permitted battery packs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fitting the attachment clip. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the handset display language . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the system display language. . . . . . . . . . . . . . . . . . . . . . . . . . .
16
16
18
19
19
19
20
21
V
Contents
Setting the handset . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Setting the speaker volume. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the ringer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Advisory tones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the vibration alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting ringing tones and pictures with resource directory. . . . . . . . . .
Viewing pictures/playing sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Renaming a picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deleting pictures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking the available memory . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating or deactivating the ringer . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating or deactivating the warning tone . . . . . . . . . . . . . . . . . . . . .
Activating/deactivating automatic call answering . . . . . . . . . . . . . . . . .
Setting the date and time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the conversion list for vCard transfer . . . . . . . . . . . . . . . . . . . .
Resetting the defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22
23
24
25
26
26
27
28
28
29
29
30
31
32
36
37
Conducting calls – enhanced functions . . . . . . . . .39
Speakerphone mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conducting calls with the headset . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Corded headset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cordless headset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Number redial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic redial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deleting a redial entry or list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adding a telephone number to the redial list. . . . . . . . . . . . . . . . . .
Entering a phone number in the call-by-call list . . . . . . . . . . . . . . . .
System speed dialling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System speed dialling, individual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System telephone directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Telephone database (LDAP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The handset’s phonebook/call-by-call list . . . . . . . . . . . . . . . . . . . . . . .
Saving an entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Finding and dialling an entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dialling an entry with the speed dialling digit. . . . . . . . . . . . . . . . . .
Viewing an entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing an entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Marking a VIP (Very Important Person) entry. . . . . . . . . . . . . . . . . .
Deleting an entry or phonebook/call-by-call list . . . . . . . . . . . . . . . .
Displaying available memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Copying the entire phonebook or individual entries. . . . . . . . . . . . .
Directed assignment of an MSN (multiple subscriber number) . . . . . .
Making calls using identification codes . . . . . . . . . . . . . . . . . . . . . . . . .
Using the handset as a second line. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deactivating the phone number display . . . . . . . . . . . . . . . . . . . . . . . .
VI
39
40
40
40
43
43
43
44
45
46
47
48
49
52
53
54
55
55
55
56
57
57
58
60
60
61
62
Contents
Directed call transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating/deactivating do not disturb . . . . . . . . . . . . . . . . . . . . . . . . . .
Call charge display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call trace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Entrance telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TDS telephone data service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating control relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sending a signal to the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External call forwarding with a multiple subscriber number . . . . . . . . .
Using night service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using dual-tone multifrequency signalling . . . . . . . . . . . . . . . . . . . . . . .
Parking/activating calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
62
63
64
65
65
67
68
69
69
71
72
73
Conducting calls – with multiple users. . . . . . . . . . 74
Call waiting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call waiting tone off/on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disabling/enabling automatic call waiting . . . . . . . . . . . . . . . . . . . . . . .
Override. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transferring a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Placing a call on hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Toggling (switching between calls) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conducting a conference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the second call function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
74
75
76
76
77
79
79
80
83
Group functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Activating/deactivating group calls . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ringing group on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UCD (Universal Call Distribution) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mulap group (Multiple Line Application) . . . . . . . . . . . . . . . . . . . . . . . .
84
87
88
92
Message functions . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Leaving a message/advisory message . . . . . . . . . . . . . . . . . . . . . . . . .
Sending/calling text messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Answering a message or voice-mail message . . . . . . . . . . . . . . . . . . .
Caller list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
94
95
97
99
Additional functions . . . . . . . . . . . . . . . . . . . . . . . . . 101
Handset alarm clock function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Handset appointment reminder function. . . . . . . . . . . . . . . . . . . . . . .
System appointment function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speed access to functions and phone numbers . . . . . . . . . . . . . . . . .
Data exchange between a PC and a handset or
101
103
106
107
108
VII
Contents
between two handsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interface overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PC application (Gigaset QuickSync) . . . . . . . . . . . . . . . . . . . . . . . .
PC interface (V24, USB). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bluetooth interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
110
110
110
111
112
Telephone blocking . . . . . . . . . . . . . . . . . . . . . . . . . .115
Handset telephone lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Telephone lock code programming . . . . . . . . . . . . . . . . . . . . . . . . . . .
Locking/unlocking the handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Central telephone lock/locking/unlocking other handsets . . . . . . . . . .
115
116
117
118
System functions . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Calling functions via the menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Calling functions via codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Functions and codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning the handset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Charging shells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EU guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
123
125
126
126
126
127
127
128
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129
VIII
Operating instructions
Step by step
Operating instructions
These operating instructions describe your handset and
its functions on your communications system.
All functions that can be performed via your handset are
described here. If some of the required functions are
not available on your handset, it may be due to one of
the following:
• The function is not configured for you or your handset - please contact your system administrator.
• Your communications platform does not feature this
function - please contact your Siemens contract
partner to upgrade.
Conducting calls –
the basic functions
You can use your handset to make both internal and external calls.
Internal calls are calls that
• you make within the range of a communication system, forexample, within your company,
• you make between networked communication systems, for example, to different company locations.
External calls are calls that you conduct with users of
the public telephone network.
1
Conducting calls – the basic functions
Step by step
Activating/deactivating the handset
a Press the On-hook key until the activation or deactivation is confirmed by a crescendo tone sequence.
PIN
If the default PIN has not been changed (0000), the
handset is ready for operation as soon as it is switched
on. If a PIN was set, it must be entered before the handset can be operated.
Please enter
PIN:
o
Enter the PIN
[ Confirm your entry. The handset is ready to use.
Displaying the connection quality
The strength of the incoming signal is displayed by the
"receive field strength" icon in on or message status:
|
Ò
Ñ
i
Ð
flashing, no reception
Low receive field strength
50% receive field strength
75% receive field strength
100% receive field strength
The radio range is different indoors and outdoors
(Æ Page 126). Please consult your system administrator in the event of range problems.
Charging the battery pack
You may only use the charging shell provided for the
handset.
The handset charges when sitting in the charging shell,
even when deactivated. If the handset is active, the
charging status display flashes on the display.
If the handset deactivates because the battery pack is
flat, it automatically reactivates and is ready for operation as soon as you place it in the charging shell. The
charging operation starts. If a PIN was set, it must be
entered first to allow charging to start.
2
Conducting calls – the basic functions
Step by step
Language
If your preferred language for the display texts is not
set, you can set this yourself (Æ Page 20).
First seize the line, then dial
c or d When the handset is idle: Press and hold down the Talk
key or press the Speakerphone key.
o
Enter the required phone number. The user will be
called.
Typing errors cannot be corrected. If you make a typing
error, press the On-hook key.
either:
p
The user answers. Conduct the call.
or:
Feature not available.
Please replace handset.
The user is busy or rejects the call. You are routed to the
other party's mailbox (if configured) or can program a
callback request Æ Page 5.
a Press the On-hook key briefly.
Dial first, then seize the line
Dialling preparation:
o and if necessary X
Enter the required phone no. and correct individual characters as necessary using the "Delete" Display key.
S Press for five seconds Insert a dial pause. A "P" appears between the digits entered. You may have to insert a pause, forexample, between the prefix and the phone number or when checking a mailbox.
Note:
The dialling preparation function is also available
with number redial and when dialling from the
handset’s phonebook (Ó).
Dialling:
c or d Press the Talk key or Speakerphone key within 30 seconds. The user will be called.
3
Conducting calls – the basic functions
Step by step
either:
p
The user answers. Conduct the call.
or:
Feature not available.
The user is busy or rejects the call. ou are routed to the
other party's mailbox (if configured) or can program a
callback request Æ Page 5.
Please replace handset.
a Press the On-hook key briefly.
Manual number redial
The last twenty phone numbers dialled are saved in the
redial list. A phone number that was dialled several
times is only saved once.
c When the handset is idle: Press the Talk key briefly. The
redial list is displayed.
s or t Select the required telephone number.
If applicable,
Show
If you want to see details on the selected phone
number: Press the display key.
either:
c or d Press the Talk or Speakerphone key briefly. The connection is set up.
or:
Options
st
Display Number
Open the redial menu. The menu contains the following
functions (Æ Page 43):
• Copy to Directory
• Automatic Redial
• Display Number
• Delete Entry
• Delete List
[ Select the menu item and confirm.
o
Change or complete the phone number, for example,
with DDIA.
c or d Press the Talk or Speakerphone key briefly. The connection is set up.
4
Conducting calls – the basic functions
Step by step
Callback
This function enables you to call a user who does not
answer or whose line is busy. The Callback function enables you to contact him as soon as he hangs up or reuses his telephone. Please note that a line is signalled
as busy when it is being called by another user. You can
continue to use your handset without restriction when
a callback has been booked.
You can also send a callback request as a message
(Æ Page 95). This function can also be called by entering the code (Æ Page 119).
Booking a callback
p
Callbck
The number is dialled. You hear the busy tone or the
user does not answer.
Save the callback request.
a Press the On-hook key to end the operation.
You receive a Callback call
You will receive the callback, as soon as the user you
want has hung up or the first time he uses his telephone. The following appears on your handset display
"Callback:...".
c or d Press the Talk or Speakerphone key briefly. The connection is set up.
Note:
Callbacks are repeated until a connection is established or until the callback is deleted. A handset can initiate up to five callbacks and can be
the destination for up to five callback requests.
If these conditions are met, any further callbacks are rejected.
5
Conducting calls – the basic functions
Step by step
Deleting a callback request
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
><
><
><
Service?
More features?
#58=View
callbacks?
[ Select the menu item and confirm.
[ Select the menu item and confirm.
[ Select the menu item and confirm.
> < Select the entry.
Mnu
><
Delete?
Call the system menu.
Call the additional menu.
[ Select the menu item and confirm.
a Press the On-hook key to end the operation.
Enquiry
You interrupt your call to consult with a user (including
external users) and then resume the original call.
p
You are on a call.
Activating and conducting an enquiry/consultation
call
S or
Enquiry
Activate consultation. The current call is placed "onhold" so that the first user waits.
o Enter the phone number for the consultation call.
p
The number is dialled. The user answers. The consultation starts.
The second user is busy or does not answer
” Cancel the enquiry. You are reconnected to the first
partner.
During the consultation you can
• book a callback (Æ Page 5),
• activate call waiting (Æ Page 74) or
• override(Æ Page 76).
6
Conducting calls – the basic functions
Step by step
The consultation is ended and you return to the
waiting call
either: The second user hangs up. You are reconnected to the
first user.
or:
Menu
><
Quit and return?
Call the system menu.
[ Select the menu item and confirm.
You are reconnected to the first partner. The second
partner hears the busy tone and hangs up; a Gigaset
handset hangs up automatically.
However, you can also
• toggle between the partners (Æ Page 79),
• set up a conference (Æ Page 80) or
• transfer the waiting partner to the second partner
(Æ Page 77).
Answering or rejecting a call
Answering a call
k
Your handset rings (Æ Page 30). The caller information
appears on the display. The name and/or telephone
number of the caller can be displayed. The following options are available for answering a call:
The handset is in the charging shell: remove the handset from the charging shell (only works if "Auto Answer"
is active Æ Page 30).
c or d The handset is not in the charging shell. Press the Talk
key or Speakerphone key.
When you have answered the call you can:
• transfer the call (Æ Page 77),
• place the call on hold and consult with someone
else in the room (Æ Page 79),
• place the call on hold and call a second partner
(Æ Page 6) in order to forward (Æ Page 77) or toggle
the call (Æ Page 79) or to set up a conference
(Æ Page 80).
7
Conducting calls – the basic functions
Step by step
Rejecting a call
If you do not wish to be disturbed, you can reject the
call.
Reject call
Confirm the message displayed with one of the two display keys. The call is rejected and the caller hears the
busy tone. ou are routed to the other party's mailbox (if
configured) or can program a callback request
Æ Page 5.
Picking up a call in a call pickup group
You can use your handset to pick up calls to telephones
within your call pickup group (set by the service engineer). This is also possible when you are conducting a
call.
Prerequisite:
You hear that a telephone in your call pickup group is
ringing.
c Press and hold down the Talk key. The message "Call
for:" appears on the display.
Menu
><
Group Pickup?
[ Select the menu item and confirm.
p
a or
Call the system menu.
k
Conduct the call.
Ending a call
Press the On-hook key briefly or place the handset in
the charging shell.
The call charges are displayed, depending on the communication system.
8
Conducting calls – the basic functions
Step by step
Forwarding calls
This function is for when you leave your desk for a while
and want certain calls to be forwarded to your new location. The forwarding destination for internal calls can
be any internal or external phone number. The destination number is usually an external phone number because you can be reached internally anytime by means
of your handset.
Activating call forwarding
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
><
Forwarding on?
Call the system menu.
[ Select the menu item and confirm.
either:
><
1=all calls?
[ Select the menu item and confirm.
or:
><
2=external
calls only?
[ Select the menu item and confirm.
or:
><
3=internal
calls only?
[ Select the menu item and confirm.
then:
o Enter the destination phone number.
Save
Save the settings.
a Press the On-hook key to end the operation.
Note:
The external code must be entered before external phone numbers. If the service engineer
has activated DTMF DID, you can also forward
calls to these external phone numbers.
9
Conducting calls – the basic functions
Step by step
Deactivating call forwarding
Prerequisite:
The room monitor function is activated.
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
><
Divert cancelled?
Call the system menu.
[ Select the menu item and confirm.
a Press the On-hook key briefly to end the operation.
Activating or deactivating the keypad
lock
This feature protects against accidentally pressing buttons when the handset is in a pocket, forexample. The
keypad lock turns off automatically when a call comes
in and turns back on when the call has ended.
# Press the hash key until the activation or deactivation is
confirmed by a crescendo tone sequence.
A key icon on the display indicates that keypad lock is
active.
After leaving the radio network
The base name flashes on the display. The handset repeatedly attempts to synchronise with a base. The intervals between synchronisation attempts increase on
account of the integrated power saving function.
You can switch off your handset to save the battery
pack.
10
Description of controls
Description of controls
Function keys
The following function keys are available:
Key
Name
Use
a
On-hook and
on/off key
•
•
•
•
End a call
Cancel functions
Jump back to the previous menu (only
following Options )
Activate or deactivate the handset
c
Talk key
•
•
•
•
Answer a call
Dial a phone number
Open the redial list
Access telephone system functions
d
Speakerphone
key
•
•
•
Answer a call
Dial a phone number
Toggle between handset to speakerphone mode
Access telephone system functions
•
f
Message list
Access message lists
*
Star key
Activate/deactivate the ringer
#
Hash key
Activate/deactivate keypad lock
C
Call-by-call key
Open the call-by-call list
S
R key
R key function
(Æ Page 12)
11
Description of controls
R key
Pressing the R key quickly performs different functions depending on the
current operating mode, for example:
• When dialling: insert a pause (for example, between the prefix and the
phone number, or when checking a mailbox)
• When conducting a call: end the call
• When conducting a consultation call: end the consultation call
• When conducting a consultation call, initiating a conference or forwarding a call: terminate the connection to a mailbox
Control key
The control key is assigned different functions depending on the operating
situation:
Situation
In idle status
During a call
In the main
menu
In lists and
menus
In the input
field
w
Open the submenu/select
Confirm (instead of OK)
Activate the selected function
Activate the selected function
Change values Save value
12
t
Press middle
Press top of
of key
key
Open the hand- Set the ringer
set’s main
menu
s
Press bottom
of key
Open the mobile’s telephone directory
Set the voice/ Open the motelephone vol- bile’s teleume
phone directory
Select a menu Select a menu
icon
icon
Next-higher
Next-lower
item in the list item in the list
Move the cur- Move the cursor up one line sor down one
line
u
Press left side
of key
v
Press right
side of key
Short: Open
the handset’s
main menu
Select "Loudspeaker Vol",
"GAP DTMF",
"Base Settings"
Select a menu Select a menu
icon
icon
Next menu lev- Select an entry
el up, cancel
(OK)
Move the cur- Move the cursor left
sor right
Reduce value
Increase value
Description of controls
Display keys
The handset has two display keys, each with one or two functions. When
the key is allocated two functions, press the right or left side of the key to
select the corresponding function. Display key assignment depends on the
operating status. A function can be represented by text or an icon.
Icon
Name
Use
©
Menu
Open the handset’s main menu or a
situation-specific menu
X
Delete
Delete the entry character by character from right to left
Î
Go Back
Go back to the next highest menu
level, cancel
[
OK
Confirm the selected menu item
Up/down
Scroll up or down to select menu
items
<>
?
Define a function Program a function for the left display key. Displayed until a function
is programmed.
Change
Change the configuration
Play
Play a melody
2ndCall
Accept call waiting
View
Display entry or picture
Off
Off
Deactivate automatic redial/function
End
End
End melody playback
Beep
Beep
Activate the warning tone
Yes
Confirm the security check question
Toggle
Toggle
Toggle between two partners
Options
Options
Open a context-specific handset
menu
Enquiry
Enquiry
Make an enquiry/consultation
Change
Play
2ndCall
View
Yes
13
Description of controls
Icon
Name
Use
Callbck
Callbck
Conduct a callback with a second
partner
Silent
Confirm handset appointment reminder call
Set
Set number keys
Save
Save entries
Phonebk
Phonebook
Open the system’s phonebook
Appoint.
Appoint.
Activate handset appointment reminder function
Dial
Dial the digits entered
Alarm
Alarm
Activate alarm function
Time
Time
Enter the time and date. Displayed
until the time and date are set.
Silent
Set
Save
Dial
Additional icons can be displayed by programming the left display key with
a function, forexample, the name of a directory or call-by-call entry
(Æ Page 108).
14
Description of controls
Menu icons in the main menu
© or w
YYou can open the handset's main menu by pressing the "Menu" display
key, by pressing the navigation key in the middle or by pressing the navigation key on the right.
The main menu is a graphical menu and contains the following menu icons:
Icon
Use
í
ì
ç
Ï
Ð
Open the "Add. Features" menu. Contains the menu
items “Data Transfer” and "Missed Dates".
Open the mask for setting the alarm clock. You can enter a wake-up time here.
Open "Calendar". Displays the calendar for the relevant
month and allows you to set a new reminder. The list
of fixed reminders also appears.
Open the "Resource Dir." menu. Contains the menu
items "Screensavers", "Caller Pictures", "Sounds" and
"Available Memory".
Open the "H/Set Settings" menu. This menu contains
the following items: "Date/Time", "Audio Settings",
"Display", "Handset" and "Base".
t/s
The menu icons are selected by pressing the top, bottom of the control
key.
15
Putting the handset into service
Putting the handset into service
Removing the protective cover
Remove the protective cover from the display before
putting the handset into service.
Inserting the battery pack
The handset is supplied with the approved battery pack. The battery pack
is not loaded. It is first charged in the handset.
Note:
•
•
•
•
•
Note: Please observe the safety notes on the back cover.
Only use the approved battery pack (Æ Page 19).
Open the battery compartment in a dust-free environment only.
Your telephone directory entries and all settings remain stored
even if you remove the battery pack. The date and time settings
will be reset.
Only remove the battery pack if it is defective. The battery
pack’s life diminishes each time it is removed.
1. Removing the attachment clip (if installed)
Insert a screwdriver between the attachment clip and the battery cover (1)
and force the attachment clip outward (2) until it dislodges.
1
2
16
Putting the handset into service
2. Opening the battery compartment
Hold your phone in you palm with the keypad facing down. With your other
hand, place your thumb on the speaker (2) and press your index finger into
the recess (1) at the top of the handset. Lift the cover up.
2
1
3. Inserting the battery pack
Insert the battery pack nose first and at an angle (3). Then press it down
into the compartment until the battery pack’s positioning clip firmly snaps
into place (4).
4
3
Note:
To remove the battery pack, you must first press the lateral positioning clip.
4. Closing the battery compartment
Position the battery cover over the compartment’s catches so that they can
snap into place (5). Then press the battery cover down until it snaps into
place (6).
6
5
5
17
Putting the handset into service
Charging and using the battery pack
To charge the battery pack, insert the handset into the charging shell with
the keypad facing forwards.
Attention:
Only use the relevant approved power supply units for operating
the charging shell (for order numbers see Æ Page 126).
The charging status is indicated by the charge status display. This flashes
during charging:
=
Battery pack is flat
e
Battery pack is 33% charged
V
Battery pack is 66% charged
U
Battery pack is 100% charged
Note:
•
•
•
18
Initial charging: Charge the battery pack for at least 10 hours
without a break, regardless of the charging status icon. Without replacing it in the charging shell, use the handset until the
"battery low" beep is heard. This action aligns the charge status
display with the operating times of the battery pack.
To attain full operating and charging times (Æ Page 19): Without replacing it in the charging shell, use the handset until the
"battery low" beep is heard.
For future charging: you can place your handset in the charging
shell each time it is used. Charging is electronically controlled
which ensures that the battery pack is charged optimally.
Putting the handset into service
Battery pack operating times and charging times
The operating times are only achieved after several charging and discharging cycles and are dependent on
• the battery capacity,
• the age of the batteries,
• the settings made,
• the user behavior,
• the DECT cordless system used
Capacity (mAh)
Stand-by mode
(hours)
Talk time
(hours)
Charging
time
(hours)
700
approx. 250 a
approx. 150 b
approx. 12
approx. 3:5
(original battery pack)
a.
b.
Operation at a Gigaset bases, such as, Gigaset S300 professional
Operation at HiPath Cordless Enterprise/HiPath Cordless Office
Permitted battery packs
Only the original Siemens battery pack is permitted for the handset.
Battery pack
Part number
Lithium-Ion, 700 mAh
V30145-K1310-X250
V30145-K1310-X322
V30145-K1310-X401
Fitting the attachment clip
Press the attachment clip onto the back of the handset until the tabs on
the sides engage in the recesses on the phone.
19
Putting the handset into service
Step by step
Setting the handset display language
If your preferred language for the handset’s display
texts is not set by default, then you can set it yourself.
The language of the communication system’s display
texts can only be set by the administrator.
Opening the main menu
© or w Open the handset’s main menu.
Opening the first submenu
st
st
either:
Ð
H/Set Settings
Ð
Einstellungen
[ Select the menu icon and confirm.
or:
[ Select the menu icon and confirm.
Opening the second submenu
either:
st
Handset
[ Select the menu item and confirm.
or:
st
Mobilteil
[ Select the menu item and confirm.
Opening the third submenu
either:
st
Language
[ Select the menu item and confirm.
or:
st
20
Sprache
[ Select the menu item and confirm.
Putting the handset into service
Step by step
Selecting a language
st
Deutsch
English
Francais
Italiano
Espanol
Portugues
Nederlands
Dansk
Norsk
Svenska
Suomi
Cesky
Polski
Turkce
Ellinika
Magyar
Russkij
Hrvatski
Slovenscina
Romana
[ Select and confirm the language you require.
a Press the On-hook key to end the operation.
Note:
•
•
If you inadvertently set a display language
that you do not understand, press "w 8 4 1"
and then select the correct language.
If you want to reset the default display language: Æ Page 37.
Setting the system display language
If you wish to change the language of the display texts,
then you must also change the system language on the
handset. A different language can be set for every handset on the system.
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
More features?
[ Select the menu item and confirm.
><
* 48=
Select language?
[ Select the menu item and confirm.
><
11=German
...
[ Select and confirm the language you require.
a Press the On-hook key to end the operation.
21
Setting the handset
Step by Step
Setting the handset
You can change the standard settings of the handset if
you are not happy with them.
Setting the speaker volume
You can adjust the speaker volume during a call. The following volumes are adjustable:
• Volume in handset mode. Three volume levels are
possible.
• Volume in speakerphone mode. Five volume levels
are possible. You can only change the speakerphone
volume if the speakerphone is active (Æ Page 39).
p
You are on a call.
© or w Open the handset’s main menu.
st
Ð
st
Audio Settings
[ Select the menu icon and confirm.
st
Handset Volume
[ Select the menu icon and confirm.
H/Set Settings
[ Select the menu icon and confirm.
__Handset Volume__
Handset:
f
g
Handsfree:
f
g
”
Save
uv Define settings.
Save
22
Press the display key if you want to permanently save
the setting.
Setting the handset
Step by Step
Setting the ringer
Setting the ringer volume and melody
Tones and melodies are saved on your handset. When
selecting the menu, the ringer sounds at the current
setting. You can choose between three ringer volumes,
as well as a crescendo ring (volume increases gradually).
You can activate distinctive ringing tones on your handset to help you differentiate between calls and appointments:
• Ext. Calls
• Internal calls
• Appointments
• All
st
Ð
© or w Open the handset’s main menu.
H/Set Settings
[ Select the menu icon and confirm.
Audio Settings
[ Select the menu item and confirm.
st
Ringer Settings
[ Select the menu item and confirm.
st
Ext. Calls
Internal Calls
Appointments
All
[ Select the required menu item and confirm. The input
st
mask, forexample, for external calls is displayed.
1 Ringer volume
1
2
___Ext. Calls___
Loudspeaker Vol:
f
Melody:
Circles g
2 Ringer melody
g
f
”
Save
uv Set volume.
s Move the cursor down one line.
... etc.
23
Setting the handset
Step by Step
Time-controlling the ringer volume and melody
Time C.
Press the display key.
1
2
___Ext. Calls___
Time control:
fOff g
from: 00:00
00:00
to:
Loudspeaker Vol:
f
”
g
Save
uv Enter the time control setting.
s Move the cursor down one line.
... etc.
Please make sure that you have picked up the call
before holding the phone to your ear. This is to
ensure that the loud ringing tone does not cause
damage to your hearing.
Save
Save the settings.
Advisory tones
The advisory tones have the following meaning:
Advisory
Meaning
Key tone
Every keystroke is confirmed
Confirmation
tones
•
•
•
Battery tone
Confirmation tone (crescendo
tone sequence) when saving inputs/settings and when placing
the handset in the charging shell
Error beep (decrescendo tone
sequence) to signal incorrect inputs
End-of-menu beep at the menu
end
The battery pack needs to be
charged
© or w Open the handset’s main menu.
24
Setting the handset
Step by Step
st
st
st
Ð
H/Set Settings
[ Select the menu icon and confirm.
Audio Settings
[ Select the menu item and confirm.
Advisory Tones
[ Select the menu item and confirm. The input mask,
forexample, for advisory tones, is displayed.
1 Key tone status
1
2
3
___Advisory Tones___
Key tone:
g
fOn
Con. tone:
g
fOn
Battery
g
fOn
Save
”
2 Confirmation tone
status
3 Battery tone status
uv Define settings.
s Move the cursor down one line.
...
Save
Save the settings.
a Press the On-hook key to end the operation.
Setting the vibration alert
st
st
st
Ð
© or w Open the handset’s main menu.
H/Set Settings
[ Select the menu icon and confirm.
Audio Settings
[ Select the menu item and confirm.
Vibration Õ
[ Select the menu item and confirm. The vibration alert is
activated or deactivated depending on the previous setting. The status is displayed in the check box (unmarked
= off).
25
Setting the handset
Step by Step
Setting ringing tones and pictures with
resource directory
Your handset’s resource directory is used to manage
sounds that you can set as ringing tones and pictures
that you can use as screensavers. Sounds are preset
and can be neither modified, loaded nor deleted.
The resource directory can manage the following media
types:
Icon
Media type
Format
Monophone ringing
tones
Standard
Polyphone ringing tones Standard
Polyphone ringing tones .mid
Picture (screensaver)
BMP
(128 x 100 or
128 x 66 pixels)
The icon is displayed in the resource directory before
the name. Your handset comes with a number of monoand polyphone sounds pre-installed. Loading/deleting
sounds is not supported. You can download pictures
from a PC (Æ Page 110) and listen to existing sounds.
Viewing pictures/playing sounds
© or w Open the handset’s main menu.
st
st
Ï Resource Dir.
Screensavers
Caller Pictures
Sounds
[ Select the menu icon and confirm.
[ Select the required menu item and confirm.
st Select the entry.
Play
or
End
Show
Press the display key. Sounds are played back or pictures are displayed.
or ” Press the display key. The handset finishes playing the
sound or displaying the picture.
While playing back sounds, you can use the u key to
interrupt playback.
26
Setting the handset
Step by Step
a Press and hold down the On-hook key to end the operation. The telephone reverts to idle mode.
If an error message appears
An error message appears after you select a picture if
you saved the image in an invalid file format. Press ”
Delete to delete the
to interrupt the operation. Press
picture.
Setting the sound volume during playback
st
[ Select the required sound and confirm. The volume can
Sound 1
Sound 2
...
be set to five different levels in the input mask.
Play
Press the display key.
Volume
Press the display key.
uv Adjust the volume.
Save
Save settings.
Renaming a picture
st
st
Ï
© or w Open the handset’s main menu.
Resource Dir.
Screensavers
Caller Pictures
[ Select the menu icon and confirm.
[ Select the required menu item and confirm.
st Select the entry.
Options
st
Rename
Open the menu.
[ The name of the entry can be modified. Length: up to
15 characters. Then confirm your entry.
a Press the On-hook key to end the operation.
27
Setting the handset
Step by Step
Deleting pictures
A picture that cannot be deleted is marked with è. In
this case, the functions listed below are not available.
© or w Open the handset’s main menu.
st
st
Ï Resource Dir.
Screensavers
Caller Pictures
[ Select the menu icon and confirm.
[ Select the required menu item and confirm.
st Select the entry.
Options
Open the menu.
either:
st
[ Select the menu item and confirm. The selected entry
Delete Entry
will be deleted.
or:
st
[ Select the menu item and confirm. All deletable entries
Delete List
in the list are deleted.
a Press the On-hook key to end the operation.
Checking the available memory
You can show how much memory is left.
© or w Open the handset’s main menu.
st
st
Ï Resource Dir.
Available Memory
[ Select the menu icon and confirm.
[ Select the menu item and confirm. The amount of
memory available/used is displayed:
_Available Memory_
Free: 13%
”
13% of the available
memory is free.
[
” or [ Press the display key. The display ends.
28
Setting the handset
Step by Step
Activating or deactivating the ringer
Deactivating the ringer
* Hold down the key until a confirmation tone is emitted.
The ringer is deactivated.
Activating the ringer
* Hold down the key until a confirmation tone is emitted.
Deactivating the ringer for the current call
* Hold down the key until a confirmation tone is emitted.
Reactivate the ringer after the call so that the handset
uses the ringer to signal the next call.
Activating or deactivating the warning
tone
When you activate the warning tone, all other tones are
deactivated. An incoming call is signalled by this brief
tone.
If the handset is in a call pickup group, a pickup call is
also signalled by the warning tone.
Activating the warning tone
* Hold down the key until a confirmation tone is emitted.
Beep on
Press the Display key within three seconds.
The warning tone is activated. The volume of the warning tone is coupled with the volume of the external ringer.
Deactivating the warning tone
* Hold down the key until a confirmation tone is emitted.
29
Setting the handset
Step by Step
Activating/deactivating automatic call
answering
This function allows you to accept calls by removing the
handset from the charging shell.
uv
st
st
Ð
© or w Open the handset’s main menu.
H/Set Settings
[ Select the menu icon and confirm.
Handset
[ Select the menu item and confirm.
Auto Answer
[ Select the menu item and confirm.
Automatic answering is activated.
The activated function is ticked and can be deactivated
by selecting it once more.
a Press the On-hook key to end the operation.
30
Setting the handset
Step by Step
Setting the date and time
The handset date and time are automatically set when
you set up a call to another station. If your communication system does not support this function, you can set
the date and time manually. The handset data and time
must be set so that calls receive the correct timestamp.
either:
st
st
Ð
© or w Open the handset’s main menu.
H/Set Settings
Date/Time
[ Select the menu icon and confirm.
[ Select the menu item and confirm.
or: If the date and time have not yet been set:
Time
Press the display key.
then:
o Enter the date, forexample, 22.09.2005 = 220905.
s Move the cursor down one line.
o Enter the time, forexample, 19:05 = 1905.
Save
Save the settings.
a Press the On-hook key to end the operation.
Note:
If your communication system does not automatically set the date and time, you must check
the setting from time to time and if necessary,
correct it.
31
Setting the handset
Step by Step
Display settings
A number of options are available for setting the display.
You can set the screensaver (screen picture), the colour
scheme, the contrast and the display lighting. You can
also change the name displayed for the base station.
Screensaver
You can set a screensaver that is displayed when the
handset is idle. It replaces the idle status display and
can even overlap the date, time and the name of the
base station. The screensaver is not displayed during a
call or if the handset is logged off.
st
st
st
Ð
© or w Open the handset’s main menu.
H/Set Settings
[ Select the menu icon and confirm.
Display
[ Select the menu item and confirm.
Screensaver
[ Select the menu item and confirm. The mask for activating and setting the screensaver is displayed.
Activation: u On v Enable or disable activation.
either:
View
The active screensaver is displayed.
or:
s Move the cursor down one line.
Selection: u Beach v Select a picture, for example "Beach".
Tip: If you select the "Clock" screensaver, the time is
shown in large digits on the display.
Edit
The selected screensaver is activated.
then:
Save
Save the settings.
a Press the On-hook key to end the operation.
32
Setting the handset
Step by Step
Colour scheme
Four colour schemes are saved on your handset. By selecting a colour scheme you define the colours to be
used for the font, menu items and background.
If you change to a different colour scheme during a setting, it is immediately previewed to show how it will appear later for all menus.
st
st
st
Ð
© or w Open the handset’s main menu.
H/Set Settings
[ Select the menu icon and confirm.
Display
[ Select the menu item and confirm.
Colour Scheme
[ Select the menu item and confirm. The colour scheme
selected is displayed.
st Selecting the colour scheme.
[ Confirm your selection.
Save
Save setting.
a Press the On-hook key to end the operation.
Contrast
Use this function to define the contrast between the
font/menu icons and the background.
st
st
st
Ð
© or w Open the handset’s main menu.
H/Set Settings
[ Select the menu icon and confirm.
Display
[ Select the menu item and confirm.
Contrast
[ Select the menu item and confirm. The mask for setting
the contrast is displayed.
u v Set the contrast.
Save
Save setting.
a Press the On-hook key to end the operation.
33
Setting the handset
Step by Step
Lighting
You can set whether the display should light up when
the handset is in the charging shell or if it is out of the
charging shell.
st
st
st
Ð
© or w Open the handset’s main menu.
H/Set Settings
[ Select the menu icon and confirm.
Display
[ Select the menu item and confirm.
Lighting
[ Select the menu item and confirm. The mask for setting
lighting is displayed.
In Charging shell: Enable or disable activation.
u On v
s Move the cursor down one line.
Outside Charging shell: Enable or disable activation.
u On v
Save
Save setting.
a Press the On-hook key to end the operation.
Base station name
You can change the base station name that is displayed
in idle status. The handset must be registered at the
corresponding base.
st
Ð
© or w Open the handset’s main menu.
H/Set Settings
[ Select the menu icon and confirm.
Handset
[ Select the menu item and confirm.
st
Select Base
[ Select the menu item and confirm.
st
<Base>
[ Select the menu item and confirm.
st
The selected base is activated. The activated base is
ticked. It can be deactivated by selecting another base.
Change
Change the settings.
Edit Name: X Delete text.
o and if necessary X
Save
Enter the required text and correct individual characters
as necessary using the "Delete" Display key.
Save the settings.
a Press the On-hook key to end the operation.
34
Setting the handset
Step by Step
aa Press the On-hook key twice to turn the handset off and
back on.
The new base station name is now displayed in idle status.
The Cordless system overwrites the display information
“Name base station” with the own phone number as
soon as an incoming or outgoing call is initiated. In this
case, the name of the base station only reappears after
the handset has been switched off and back on again.
35
Setting the handset
Step by Step
Setting the conversion list for vCard
transfer
Phone numbers are usually specified as follows in email programs, such as, Microsoft Outlook: +49 (05251)
820776. The handset is unable to use this format, however, to dial the phone number. If the phone number
above is a local fixed network number, it is converted to
0820776, for instance. The conversion pairs are defined
in the conversion table and can be modified if they deviate from the default values.
Consult your system administrator about the conversion rules that apply to your handset.
Defining conversion pairs
st
st
st
Ð
© or w Open the handset’s main menu.
H/Set Settings
[ Select the menu icon and confirm.
Handset
[ Select the menu item and confirm.
Area Codes
[ Select the menu item and confirm. The conversion ta-
ble is displayed. It is predefined for the country in question and may be displayed in the following format:
____Area Codes____
International code:
00 - 49
Local area code:
0 - [I
]
”
1 The country code "49" is
replaced by "00"
2 The area code, for instance "05251" (blank in
this example), is replaced by "0"
2
1
Save
o Change entry.
Press the top/bottom control key to navigate to another
input field; press the left/right control key to move the
cursor within an input field.
Save
Save setting.
a Press the On-hook key to end the operation.
36
Setting the handset
Step by Step
Resetting the defaults
This function allows you to reset your mobile phone to
the defaults, forexample, if you want to pass it on to
someone else or reset it.
The handset features are handled as follows:
Feature
Action
Sound settings
are reset
Call-by-call list
is retained
System registration
is retained
Phonebook
is retained
Redial list
is deleted
Resetting
st
st
st
Ð
© or w Open the handset’s main menu.
H/Set Settings
[ Select the menu icon and confirm.
Handset
[ Select the menu item and confirm.
Reset Handset
[ Select the menu item and confirm. A security check
question appears.
Yes
Confirm the security check question. The handset is returned to the default.
Note:
For information about deleting the telephone directory see: Æ Page 57.
37
Setting the handset
Default settings
Setting
Explanation/notes
Levels
Tones and
signals
Ringer volume
5
Default
state
5
Ringer melody, external
Ringer melody, internal
3 +30
3 +30
1
3
Warning tone
Handset volume
3
off
1
Volume in speakerphone mode
Appointment
5
3
3+30
5
1
5
Melody
Volume
Key tones, audible each time a key is pressed.
on
Warning tone, audible approximate- ly five minutes before the battery
runs out.
on
Confirmation tone, indicates wheth- er actions were successful or unsuccessful.
Vibration
-
on
Auto Answer Call is automatically accepted by re- moving the handset from the charging shell.
on
Select Base
Lighting
Select the base
Display lighting
4
-
retained
on
Screen Picture
Display in idle status
-
off
Character
Set
Language
Available character set
-
Standard
Select different languages:
20
English
or
German
Bluetooth
Bluetooth-Activation
Default state Resetting the defaults deletes the redial call numbers and resets the
sound settings. The registration (logon) and the handset PIN are retained.
38
on
off
-
Conducting calls – enhanced functions
Step by Step
Conducting calls – enhanced
functions
Speakerphone mode
Features
Speakerphone mode offers you the following advantages:
• Other persons can listen to and participate in the
call.
• Your hands are free.
• When dialling, you can hear the ring tone, for example, without having to lift the handset to your ear.
Speakerphone mode can be used effectively up to a
background noise level of 50 dB (A) (Office environment).
Activating speakerphone mode
Speakerphone mode can be activated during a call,
when dialling or when answering a call:
d
Press the Speakerphone key. The Speakerphone key
lights up. Inform the other party when you want to activate the speakerphone to let others listen in.
Note:
Make sure you switch back to handset mode before you return the telephone directly to your ear.
In this way you can avoid causing damage to your
hearing.
Switching between speakerphone and handset
mode
d
Press the Speakerphone key. The handset switches
from speakerphone to handset mode or vice versa.
The Speakerphone key lights up if speakerphone mode
is active. It does not light up if speakerphone mode is
deactivated and handset mode is activated.
39
Conducting calls – enhanced functions
Step by Step
Note:
If you wish to replace the handset in the charging shell during a call, forexample, because the
battery pack is flat, hold down the Speakerphone key to prevent the call from being cleared
down.
Setting the speakerphone volume
The volume can be set during a call (Æ Page 22).
Conducting calls with the headset
The handset can be used with a corded and cordless
headset.
Corded headset
You can connect a corded headset via the jack on the
underside of the handset. The headset must have a
SLIM Lumberg connector.
The receiver inset and microphone functions are activated on the headset once it is connected.
Cordless headset
You can use a cordless, Bluetooth-enabled headset
with your handset. This means your hands are free
while making calls and there are no annoying cables to
disrupt your computer work in the office or on the road,
forexample.
Your Bluetooth headset must be registered on your
handset before you can use it for the first time. After
this, you can continue to use your Bluetooth headset
until you decide to deregister it.
Note:
• Theoretically, third parties can tap Bluetooth
connections.
• To improve protection against unauthorised
tapping, deregister any Bluetooth devices
you no longer require.
During a call, a second caller is not signalled via the
Bluetooth headset.
40
Conducting calls – enhanced functions
Step by Step
Registering a Bluetooth headset at the handset
Set the headset to login mode (see the user manual
supplied with your headset).
© or w Open the handset’s main menu.
st
í Extras
[ Select the menu icon and confirm.
st
Data Transfer
[ Select the menu icon and confirm.
st
Bluetooth
[ Select the menu item and confirm. The Bluetooth menu
st
Search Headset
st
Found Devices
S55 Headset
is displayed.
[ Select the menu item and confirm. The handset searches for a Bluetooth headset and sets up a wireless connection. The name of the devices found are displayed.
Select the required headset.
Options
Open the handset’s menu
st
Trust Device
[ Select the menu item and confirm.
st
agreed PIN:
[ Enter and confirm the Bluetooth PIN for your headset
st
Activation Õ
(see your headset user manual). The device is recorded
in the list of known devices.
[ The Bluetooth interface is automatically activated on
your handset.
The active Bluetooth function is ticked.
Conducting calls via the Bluetooth headset
Activating the Bluetooth headset during a call
If the handset is in dial or call mode (establishing a call
connection Æ Page 3), the Bluetooth headset can assume the receiver inset and microphone functions.
Press the Talk key on the Bluetooth headset (refer to the
headset user manual).
41
Conducting calls – enhanced functions
Step by Step
Accepting a call on the Bluetooth headset
The headset uses a call tone to signal an incoming call.
Press the Talk key on the Bluetooth headset (refer to the
headset user manual).
Deactivating the Bluetooth headset during a call
You are conducting a call via the Bluetooth headset.
c or d Press the Talk key or Speakerphone key on the handset.
The Bluetooth headset is deactivated. You can continue
the call directly on the handset.
Deregistering the Bluetooth headset at the handset
To improve protection against unauthorised tapping, deregister the Bluetooth headset at the handset if you no
longer wish to use it.
© or w Open the handset’s main menu.
st
í Extras
[ Select the menu icon and confirm.
st
Data Transfer
[ Select the menu icon and confirm.
st
Bluetooth
[ Select the menu item and confirm. The Bluetooth menu
st
Trusted Devices
S55 Headset
st
Delete Entry
is displayed.
[ Select the menu item and confirm. The name of the
registered or recognised Bluetooth headset is displayed.
Options
42
Open the handset’s menu
[ Select the menu item and confirm. The Bluetooth head-
set is deregistered or no longer recognised by the handset.
Conducting calls – enhanced functions
Step by Step
Number redial
The last twenty phone numbers dialled are saved in the
redial list. A phone number that was dialled several
times is only saved once.
If you tried to call a party from the handset’s telephone
directory, the name of the party is displayed in case of
number redial. For information on manual number redial, see (Æ Page 4).
Automatic redial
The phone number is automatically redialled ten times
at 20-second intervals. Speakerphone mode is automatically activated, the Speakerphone key flashes. The
function is deactivated after ten unsuccessful attempts
and when a call is made in the interim.
c Press the Talk key briefly. The redial list is displayed.
s or t Select the required telephone number.
Options
st
Automatic Redial
Open the redial menu.
[ Select the menu item and confirm. Automatic redial is
activated.
either:
p
The user answers and you conduct the call.
or:
Off
If you wish to cancel the function: press the Display key
or any key.
Deleting a redial entry or list
c Press the Talk key briefly. The redial list is displayed.
s or t Select the required telephone number.
Options
Open the redial menu.
either:
st
Delete Entry
[ Select the menu item and confirm. The telephone
number is deleted.
or:
43
Conducting calls – enhanced functions
Step by Step
st
[ Select the menu item and confirm. The redial list is de-
Delete List
leted.
a Press the On-hook key to end the operation.
Adding a telephone number to the redial list
During dial preparation, you can add a number displayed
in the handset’s redial list to your phonebook.
c Press the Talk key briefly. The redial list is displayed.
s or t Select the required telephone number.
Options
st
Copy to Directory
st
New Entry
Open the redial menu.
[ Select the menu item and confirm. The phonebook is
displayed.
[ Select the menu item and confirm. The following selection mask appears:
Insert number
999
to:
<
f
g
”
[
uv Mark where you want to add the phone number. You
can choose between Phone (Home), Phone (Office),
and Phone (Mobile).
[ Confirm your entry.
st o Enter the remaining contact information, such as, first
name and surname. For further information, see
Æ Page 52 and Æ Page 53.
44
Conducting calls – enhanced functions
Step by Step
Entering a phone number in the call-by-call
list
You can manually enter a phone number in the call-bycall list.
C When the handset is idle: Open the call-by-call list.
st
New Entry
[ Select the menu item and confirm. The input mask is
displayed. The line where you can enter information is
marked active with [...].
o Enter the relevant information, see above.
st Jump to the next line.
... etc.
Functions for text input:
#
X
*
Save
Switches mode from abc to Abc, from Abc
to 123 and from 123 to abc
If predictive text is off:
press the key briefly.
If predictive text is on:
press and hold down the key.
Deletes the letter to the left of the cursor.
Opens the table of special characters.
Save the settings.
a Press the On-hook key to end the operation.
45
Conducting calls – enhanced functions
Step by Step
System speed dialling
Your system administrator can save up to 1000 external
phone numbers as system speed dialling destinations
in your communication system. You can dial these
speed dialling destinations with a three-digit code (000
- 999).
Dialling a system speed dialling destination
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
* 7=Use speed
dialing?
[ Select the menu item and confirm. This function can
also be activated directly by entering the appropriate
code (Æ Page 119).
o Enter the required code (3 digits, 000 - 999).
Note:
The saved speed dialling destinations and the
associated codes can be obtained from the organisational unit responsible for administering
the communication system.
Dialling a system speed dialling destination with
suffix-dialling or a DID number
System speed dialling destinations can be saved in your
communication system and then dialled by means of
suffix-dialling or DDIA. These speed dialling destinations let you enter an additional suffix-dialling or DID
number up to five seconds after entering the three-digit
service code. If you do not make an entry within this
time frame, the default suffix-dialling number,
forexample, "0" for the exchange, is dialled.
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
><
46
Service?
Call the system menu.
[ Select the menu item and confirm.
Conducting calls – enhanced functions
Step by Step
><
[ Select the menu item and confirm.
* 7=Use speed
dialing?
o Enter the required code (3 digits, 000 - 999).
o Within five seconds: enter the suffix-dialling or DID
number.
System speed dialling, individual
You can save up to ten external phone numbers as
speed dialling destinations for your handset in your
communication system. These speed dialling destinations are dialled using a 2-digit code (*0 to *9). Please
note that you may need to save an external code in front
of the phone number.
This function can also be called by entering the code
(Æ Page 119).
Setting up an individual speed dialling destination
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
* 92=Change Speed
Dial?
[ Select the menu item and confirm.
Abb. dial no:
> Call the first destination.
> Call the next destination.
Mnu
><
Change entry?
Call the additional menu.
[ Select the menu item and confirm.
o Enter the external phone number (with external code).
Save
Save the settings.
a Press the On-hook key to end the operation.
47
Conducting calls – enhanced functions
Step by Step
Dialling an individual speed dialling destination
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
* 7=Use speed
dialing?
[ Select the menu item and confirm.
Abb. dial no:
* o Enter the code for the speed dialling destination.
System telephone directory
If the system administrator has entered a name for at
least one internal user or system speed dialling destination, then you can use the system telephone directory
for dialling purposes.
Calling the system telephone directory
c or d Press and hold down the Talk key or press the Speakerphone key.
Phonebk
Call the system telephone directory. The first entry appears.
If applicable:
><
1=intnl
[ If more than one telephone directory is configured: Select the menu item and confirm.
Finding an entry
o Enter the first letters of the name you are looking for.
The name search begins.
The search result becomes more precise as each letter
is entered, i.e. the number of names found is reduced.
> < Select the user you want.
Dialling the entry
[ Confirm your selection. The selected number is called.
48
Conducting calls – enhanced functions
Step by Step
Quitting the redial list
” Press the display key.
Note:
Phone numbers dialled from the "System telephone directory" are not stored in the redial list.
Telephone database (LDAP)
If your company has an LDAP telephone database and
access to it is configured in your communication system, you can query it with your handset. This LDAP telephone database can contain far more entries than the
telephone directory on your communication system or
your handset. The LDAP telephone database is installed
on an LDAP server. This telephone database is accessed over the LDAP Internet protocol (Lightweight
Directory Access Protocol).
This function can also be called by entering the code
(Æ Page 119).
Activating the LDAP telephone database
c or d Press and hold down the Talk key or press the Speakerphone key.
Phonebk
Press the display key.
If applicable:
><
2=LDAP
[ If more than one telephone directory is configured: Select the menu item and confirm.
Entering a name and finding an entry
You can now enter the name over the handset’s keypad.
Each key is assigned several letters and each letter is
selected by pressing the key an appropriate number of
times. Forexample, you must press the "7" key three
times to enter an "r".
o Enter the name you want to find (maximum 16 characters). Partial entries are accepted, forexample, "mei" for
Meier. The more characters entered, the more precise
the search result.
49
Conducting calls – enhanced functions
Step by Step
If configured, you can search for first and last names.
First and last names must be separated by a space. Do
this by pressing the "0" key. Partial entries are accepted,
forexample, "mei P" for "Meier Peter".
If applicable:
><
Delete Character?
><
Search?
[ If you wish to delete an incorrect letter entered by mistake: Select the menu item and confirm.
then:
[ Select the menu item and confirm. The system starts to
search for the entry. This can take a few seconds. The
entries found are then displayed.
Selecting an entry
either: If a single entry is found, it is displayed.
Call?
[ Select the menu item and confirm. The user will be
called.
or: If more than one entry is found, the first entry is displayed. A maximum of 50 hits can be displayed.
><
Scroll Next?
><
Scroll Previous?
><
Call?
[ If you wish to scroll forward: Select the menu item and
confirm.
[ If you wish to scroll backward: Select the menu item
and confirm.
[ Select the menu item and confirm. The user will be
called.
If no entries were found
If no entries were found, you can extend the search
range by deleting some of the characters entered.
><
50
Change search
string?
[ Select the menu item and confirm. You can now change
your search entry.
Conducting calls – enhanced functions
Step by Step
If too many entries were found
The hit list is not displayed in full if more than 50 entries
matching your search query were found. We recommend narrowing down the search by entering more
characters. However, even if you do not do this, you can
still display the entire hit list, select the required entry
and call the selected party.
either:
><
Change search
string?
><
Show results?
[ Select the menu item and confirm. You can now change
your search entry.
or:
[ Select the menu item and confirm. The hit list is displayed.
51
Conducting calls – enhanced functions
The handset’s phonebook/call-by-call list
A total of up to 250 entries can be saved in the phonebook and the call-bycall list. The phonebook and the call-by-call list are operated in the same
way.
Gigaset QuickSync Æ Page 110 is a software application for transferring
data between your cordless Gigaset phone and your PC. You can use it at
your phone to load data from your PC to your Gigaset over a data cable or
Bluetooth and synchronize contacts with Microsoft Outlook, Microsoft
Outlook Express, and contacts in Microsoft Windows Vista.
Phonebook:
You can save contact information for frequent call partners in the phonebook. Once a phone number has been saved in this way you no longer
have to enter it in full when you want to call someone. All you have to do
is select the required phonebook entry.
You can save the following contact information for every entry in the phonebook:
Information
Explanation
First Name*,
Surname
A name must be entered in at least one of the fields.
Each name can contain up to 16 characters.
Phone,
Phone (Mobile)*,
Phone (Office)*
A number must be entered in at least one of the fields.
Each number can contain up to 32 digits.
E-Mail*
E-mail address with up to 60 characters. The special
character "@" can be inserted after pressing the asterisk key.
Anniversary
You can select either "On" or "Off". If "On" is selected:
• Anniversary (Date): Day/month/year, 8 digits*
• Anniversary (Time): Hour/minute, 4 digits, for reminder call
• Anniversary (Signal): Type of signalling, acoustic or
visual (time specification not necessary)
CLIP picture*
Displays a picture for an incoming call when CLIP is active.
Note: This function is not supported by the system and
should therefore not be used.
VIP Entry
VIP mark and VIP ringing tone. Reached by pressing
Options .
* = new for vCard format
52
Conducting calls – enhanced functions
Step by Step
Call-by-call list:
You can save carrier prefixes, for instance, in the call-bycall list. The following information applies to each entry.
Information
Explanation
Number:
Up to 32 digits
PublicKey:
Up to 16 characters
Saving an entry
s or C When the handset is idle: Open the phonebook or callby-call list.
st
New Entry
[ Select the menu item and confirm. The input mask is
displayed. The line where you can enter information is
marked active with [...].
o Enter the relevant information, see above.
st Jump to the next line.
... etc.
Functions for text input:
#
X
*
Save
Switches mode from abc to Abc, from Abc
to 123 and from 123 to abc
If predictive text is off:
press the key briefly.
If predictive text is on:
press and hold down the key.
Deletes the letter to the left of the cursor.
Opens the table of special characters.
Save the settings.
a Press the On-hook key to end the operation.
53
Conducting calls – enhanced functions
Step by Step
Changing the sequence of entries:
The phonebook entries are generally sorted in alphabetical order by surname. Spaces and digits have first priority here. If the phonebook only contains a subscriber’s
first name, this is listed instead of the surname in the
sequence.
The sort sequence is as follows:
1. Space
2. Digits (0 - 9)
3. Letters (alphabetical)
4. Other characters
If you want to change the sequence of entries in the alphabetical list, you could insert a space or a digit before
the first letter of the surname. These entries then move
to the top of the phonebook. Names preceded by an asterisk are listed at the end of the phonebook.
Finding and dialling an entry
s or C When the handset is idle: Open the phonebook or callby-call list.
t/s or o You can scroll to the required entry or enter the first letter of the relevant entry.
If necessary, press a key several times in succession to
enter the required letter.
either:
c Press the Talk key. The assigned phone number is dialled.
or:
Options
st
Display Number
Open the menu.
[ Select the menu item and confirm. The number is displayed.
o
Change or complete the phone number, forexample,
with DDIA.
c Press and hold down the Talk key.
54
Conducting calls – enhanced functions
Step by Step
Dialling an entry with the speed dialling digit
You can call up and dial the phone number associated
with an entry that you saved in the call-by-call list and assigned a speed dialling digit by simply pressing this
speed dialling digit (Æ Page 108).
o Press and hold down the required speed dialling digit.
The assigned phone number is shown on the display.
c Press and hold down the Talk key. The assigned phone
number is dialled.
Viewing an entry
s or C When the handset is idle: Open the phonebook or callby-call list.
t/s or o You can scroll to the required entry or enter the first letter of the relevant entry.
If necessary, press a key several times in succession to
enter the required letter.
Show
Press the display key. The entry’s data is displayed.
[ Confirm to return to the list.
a Press the On-hook key to end the operation.
Changing an entry
s or C When the handset is idle: Open the phonebook or callby-call list.
t/s or o You can scroll to the required entry or enter the first letter of the relevant entry.
If necessary, press a key several times in succession to
enter the required letter.
either:
Show
Press the display keys one after the other. The entry’s
data is displayed.
Edit
or:
Options
st
Edit Entry
Open the menu.
[ Select the menu item and confirm. The entry’s data is
displayed.
55
Conducting calls – enhanced functions
Step by Step
then:
o Enter changes.
Options
st
Save Entry
Open the menu.
[ Save the entry.
a Press the On-hook key to end the operation.
Marking a VIP (Very Important Person) entry
s When the handset is idle: Open the phonebook.
s t Select the required entry.
Options
st
VIP Entry
Open the menu.
[ Select the menu item and confirm. The input mask for
marking a VIP entry is displayed.
VIP: u Ein v Activate the VIP marking.
s Move the cursor down one line.
Melody: u Circles v Select a melody, forexample, "Circles".
a Press the On-hook key to end the operation.
56
Conducting calls – enhanced functions
Step by Step
Deleting an entry or phonebook/call-by-call
list
s or C When the handset is idle: Open the phonebook or callby-call list.
s t Select the required entry.
Options
Open the menu.
either:
st
Delete Entry
st
Delete List
[ Select the menu item and confirm. The telephone
number is deleted.
or:
[ Select the menu item and confirm. A security check
question appears.
Yes
Confirm the security check question. The phonebook/
call-by-call list is deleted.
a Press the On-hook key to end the operation.
Displaying available memory
s or C When the handset is idle: Open the phonebook or callby-call list.
t s Select any entry.
Options
st
Available Memory
Open the menu.
[ Select the menu item and confirm. The amount of
memory used and available is displayed.
a Press the On-hook key to end the operation.
57
Conducting calls – enhanced functions
Step by Step
Copying the entire phonebook or individual
entries
If your handset and the recipient’s handset have phone
numbers between 1 and 99, you can send or receive a
list or entry directly from one handset to the other. If the
handsets’ phone numbers start at 100, you must first
send the list or entry to the communication system. The
recipient can then use his or her handset to download
the list or entry from the communication system.
Restrictions when copying over the communication system
The entries in the handset’s phonebook are stored in
vCard format (Æ Page 52). The communication system,
however, uses another format. This can cause loss of
phonebook entry information. The features that are new
for the vCard format are indicated by an asterisk (= new
for vCard format) in the table on Æ Page 52. The phone
numbers are not affected.
Sending a list/entry
s Open the phonebook.
t s Select the entry.
© or w Open the handset’s phonebook menu.
either:
st
Copy List
[ Select the menu item and confirm.
or:
st
Copy Entry
[ Select the menu item and confirm.
then:
o Enter a phone no. The following phone numbers are
possible:
• 1... 98 – the list or entry is sent directly to the recipient’s handset.
• 00 – the list or entry is sent to the communication
system and can then can be downloaded by any
handset.
• 99 – The list or entry is sent to the communication
system and can then can only be downloaded by
your handset.
[ Confirm your entry. The list or entry is sent.
58
Conducting calls – enhanced functions
Step by Step
If a phone number from 1 to 98 was dialled, the list or
the entry is automatically received by the recipient’s
handset.
Loading a list or entry from the communication system
Prerequisite: You sent an entry or list to the communication system by dialling the phone number 00 or 99.
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
Load list buffer?
[ Select the menu item and confirm. The handset starts
to load the list/entry.
a Press the On-hook key to end the operation.
Deleting a list or entry in the communication system
Prerequisite: A currently unused list or entry is saved on
the communication system.
If the handset with phone number 00 was used to send
the list or entry to the communication system, any
handset can be used to delete this list or entry. If the list
or entry was sent by the handset with the phone
number 99, the list or entry can only be deleted by the
handset that sent it.
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
Erase list buffer?
[ Select the menu item and confirm. The handset starts
to delete the list/entry.
a Press the On-hook key to end the operation.
59
Conducting calls – enhanced functions
Step by Step
Directed assignment of an MSN
(multiple subscriber number)
Multiple subscriber numbers are phone numbers belonging to an ISDN multiple device line. They are used
for the directed addressing of terminals, for example
when a fax machine has a separate number. Before selecting an external connection, you can directly assign a
configured multiple subscriber number. This then appears on the called party’s display.
This function can also be called by entering the code
(Æ Page 119).
c or d Press the Talk or Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
* 41=Temporary
MSN?
[ Select the menu item and confirm.
MSN no.111
o Enter the required multiple subscriber number.
111:
o Enter the required external phone number. The phone
number is dialled.
Making calls using identification
codes
In the case of calls you make to external partners, you
can enter and charge the call costs on the basis of individuals, customers, accounts and private calls,
forexample, by means of account codes. The account
code (ACCT) can contain up to 11 characters and is included in the data printout. The ACCT is only transferred
after a call has been completed. The ACCT can be entered before and during the external call.
This function can also be called by entering the code
(Æ Page 119).
c or d Press the Talk or Speakerphone key.
Menu
><
60
Service?
Call the system menu.
[ Select the menu item and confirm.
Conducting calls – enhanced functions
Step by Step
><
* 60=
Account code?
[ Select the menu item and confirm.
Project Code:
o Enter the required account code (optional).
Save
Please dial.
Save the settings.
o Enter an external phone number. The phone number is
dialled.
Note:
If a call is transferred, the costs are still assigned
to the ACCT entered.
Using the handset as a second line
You can use your mobile phone for an outgoing call as if
it were another line (temporary phone).
This function can also be called by entering the code
(Æ Page 119).
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
* 508=Temporary
Phone?
[ Select the menu item and confirm.
Home Extn. no.:
o Enter the internal phone number for the relevant line.
o Enter the code (lock code) for the relevant line
PIN no:
<Name>
(Æ Page 116).
If there is no personal code for the relevant line, the system will prompt you to enter the code.
Note:
IDo not use the default phone code (00000) for
the user..
<Name>: ...
o Enter the required phone number. The phone number is
dialled.
The "Temporary phone" function is discontinued again
after the call is complete.
61
Conducting calls – enhanced functions
Step by Step
Deactivating the phone number display
Your service engineer can deactivate the display of your
phone number and name on the called party’s display
for external outgoing calls. You can also activate and deactivate the phone number display on your own handset yourself.
Deactivating the phone number display
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
><
Suppress call ID?
Call ID suppressed
Call the system menu.
[ Select the menu item and confirm.
a Press the On-hook key to end the operation.
Activating the phone number display
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
><
Restore caller ID?
Call ID restored
Call the system menu.
[ Select the menu item and confirm.
a Press the On-hook key to end the operation.
Directed call transfer
You can transfer calls to other telephones to your handset. This is also possible when you are conducting a call.
This function can also be called by entering the code
(Æ Page 119).
Another telephone rings.
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
* 59=Pickup directed?
[ Select the menu item and confirm. The called user is
62
displayed.
Conducting calls – enhanced functions
Step by Step
Mnu
Call the additional menu.
either:
><
[ Select the menu item and confirm.
Accept call?
or:
Note:
If several users are called simultaneously, only
the first user called is displayed. However, you
can transfer by entering the phone number of
any of the users called.
><
[ Select the menu item and confirm.
Select
extension?
then:
p
Conduct the call.
Activating/deactivating do not disturb
You can block calls to your handset on a temporary basis, while still being able to make calls yourself. Internal
callers hear the busy tone, while external callers reach
another telephone defined by the service engineer (intercept position). Authorised internal callers automatically override the do not disturb after five seconds.
Activating do not disturb
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
><
Call the system menu.
[ Select the menu item and confirm.
Do Not Disturb ON?
a Press the On-hook key to end the operation.
Deactivating do not disturb
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
><
Do Not Disturb OFF?
Call the system menu.
[ Select the menu item and confirm.
a Press the On-hook key to end the operation.
63
Conducting calls – enhanced functions
Step by Step
Call charge display
After a call has ended, the display shows the connection charges for the current call as standard. If the costs
are to be displayed continuously during an outgoing call,
this function must be requested from the carrier.
Note:
If a call is transferred, the costs are assigned to
the telephone to which the call was transferred
from this point onwards.
You can check and display the call charges for your
phone number as a total for a period that can be set by
the service engineer.
First the call charges for the last charged call are displayed. The total call charges are displayed after five
seconds.
This function can also be called by entering the code
(Æ Page 119).
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
* 65=Show call charges?
[ Select the menu item and confirm.
64
a Press the On-hook key to end the operation.
Conducting calls – enhanced functions
Step by Step
Call trace
You can apply to your carrier for "call tracing" on malicious calls. An authorised extension is then in a position
to request the identification of the phone number.
This also works for 30 seconds after the malicious caller
has hung up. However, you should not hang up.
This function can also be called by entering the code
(Æ Page 119).
p
Menu
You receive a malicious call.
Do not hang up.
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
* 84=Trace call?
[ Select the menu item and confirm. The caller is identified in the attendant console.
a Press the On-hook key to end the operation.
Entrance telephone
If the service engineer has set up an entrance telephone, you can speak to the door intercom and activate
the door opener from your handset.
If you are authorised to release a door, then a user can
open the door by entering a five-digit code (forexample,
by means of a DTMF transmitter or installed keypads).
Some of the functions described below can also be
called directly by entering the relevant code
(Æ Page 119).
Talking to a visitor by means of the door opener
equipment
Your handset rings.
either:
c Press the Talk key within 30 seconds. You are connected
immediately to the door opener.
or:
c If more than 30 seconds have passed: Press and hold
down the Talk key.
65
Conducting calls – enhanced functions
Step by Step
o Enter the internal phone number for the door opener.
You are connected to the door opener.
Using the handset to open the door opener during
a call
><
Open door?
[ Select the menu item and confirm.
Using the handset to open the door opener without
holding a conversation
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
* 61=Open door?
[ Select the menu item and confirm.
o Enter the internal phone number for the door opener.
The door is opened.
a Press the On-hook key to end the operation.
Activating the door release
This function only works if it has been configured by the
service engineer.
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
* 89=Door release
ON?
[ Select the menu item and confirm.
o Follow the user guidance system from this point on-
wards. Enter the internal phone number of the door
opener, as well as the code and type of door release:
• 1=enable with ring,
• 2=enable w/o ring,
• 3=change password.
[ Confirm your entries.
a Press the On-hook key to end the operation.
66
Conducting calls – enhanced functions
Step by Step
Note:
Standard code 00000. To change the code, confirm option "3=change password". Follow the
user guidance system.
Deactivating the door release
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
* 89=Door release
OFF?
[ Select the menu item and confirm.
a Press the On-hook key to end the operation.
TDS telephone data service
You can use your mobile phone to operate connected
computers and their programs, forexample, access hotel services or information systems.
This function can also be called by entering the code
(Æ Page 119).
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
* 42=
Tel. data service?
[ Select the menu item and confirm.
TDS code:
# o Press the "#" key and enter the required code (0... 9).
The connected computer responds. The computer will
guide you through the data entry process. It will process your entries directly.
a Press the On-hook key to end the operation.
67
Conducting calls – enhanced functions
Step by Step
Activating control relays
The service engineer can set up a maximum of 4 control
relays that enable various equipment (forexample, door
opener) to be activated and deactivated.
It is possible to access a specific control relay. Depending on the configuration, the control relays can be
• activated and deactivated automatically, or
• activated and deactivated automatically on the basis
of a timer.
Prerequisite: The service engineer has set up at least
one switch.
This function can also be called by entering the code
(Æ Page 119).
Activating a control relay
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
* 90=Control Relay
On?
[ Select the menu item and confirm.
o Follow the user guidance system from this point onwards. Enter the required switch code (1... 4).
a Press the On-hook key to end the operation.
Deactivating a control relay
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
#90=Control Relay
Off?
[ Select the menu item and confirm.
o Follow the user guidance system from this point onwards. Enter the required switch code (1... 4).
a Press the On-hook key to end the operation.
68
Conducting calls – enhanced functions
Step by Step
Sending a signal to the network
To enable ISDN-type services/ features to be started via
analog lines (forexample, call waiting when a line is
busy, three-way conference calls, etc.), you must send
a signal to the network before dialling the service code
and/or phone number.
This function can also be called by entering the code
(Æ Page 119).
p
Menu
You have an external connection.
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
* 51=Recall to Network?
[ Select the menu item and confirm.
o Enter the service code and/or the phone number.
External call forwarding with a
multiple subscriber number
If your communication system is connected to an ISDN
multiple device line, then you can forward all incoming
calls from the public network through your multiple subscriber number (MSN) to an external destination.
There are three types of forwarding:
• Calls are forwarded immediately (1=immediate call
forwarding).
• Calls are forwarded after a certain time (2=unanswered calls).
• Calls are only forwarded when the line is busy
(3=when busy).
Activating call forwarding to a "trunk"
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
Trunk FWD on?
[ Select the menu item and confirm.
o [ Enter and confirm your own multiple subscriber
number.
69
Conducting calls – enhanced functions
Step by Step
either:
><
[ Select the menu item and confirm.
1=immediate?
or:
><
2=on no answer?
><
3=on busy?
[ Select the menu item and confirm.
or:
[ Select the menu item and confirm.
then:
o Enter the phone number of the destination (without external code).
Save
Save the settings.
Deactivating call forwarding to a "trunk"
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
Forward by Network
OFF?
[ Select the menu item and confirm.
o Follow the user guidance system from this point on-
wards (enter a multiple subscriber number or DID and
forwarding type).
[ Confirm your entries.
a Press the On-hook key to end the operation.
70
Conducting calls – enhanced functions
Step by Step
Using night service
In night service mode, forexample, during lunch breaks
or after office hours, all external calls are forwarded to a
particular internal telephone (night station). The night
station can be defined by the service engineer (= standard night service) or by you (= temporary night service).
When night service is active, the night station assumes
the function of the intercept station.
Activating night service
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
><
Call the system menu.
[ Select the menu item and confirm.
Night answer on?
either:
><
[ Select the menu item and confirm.
*=default?
"Standard night service" is configured.
or:
o Enter an internal phone number.
Save
Save the settings.
"Temporary night service" is configured.
a Press the On-hook key to end the operation.
Deactivating night service
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
><
Night Service - OFF?
Call the system menu.
[ Select the menu item and confirm.
a Press the On-hook key to end the operation.
71
Conducting calls – enhanced functions
Step by Step
Using dual-tone multifrequency
signalling
Your handset operates on the basis of digital information transmission. However, certain applications,
forexample, answering machines, can only be operated
using analog technology. For this you must send signals
using the dual-tone multifrequency signalling (DTMF)
process.
Depending on how your system is configured (automatic tone dialling on or off - to be configured by the service
engineer) you must first switch to DTMF dialling. This
means, forexample, that you can communicate with a
variety of voice storage systems.
You will find further details in the operating instructions
for the relevant applications.
Automatic tone dialling is not active
During a connection you must first switch to dual-tone
multifrequency signalling.
p
Menu
You are on a call.
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
* 53=Tone dialling?
[ Select the menu item and confirm.
o
Enter the numbers. All entries are sent as DTMF signals.
Automatic tone dialling is active
o
72
Enter the numbers. All entries are sent as DTMF signals.
Conducting calls – enhanced functions
Step by Step
Parking/activating calls
You can park up to ten calls (i.e. place them on hold) and
then reactivate them at other telephones in your communication system.
Parking a call
p
Menu
You are on a call you wish to park.
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
* 56=Park a call?
[ Select the menu item and confirm.
o Enter and note the parking position number (0... 9).
If the parking position number entered is already in use,
you must enter another one.
Picking up a specific parked call
Prerequisite:
One or more calls have been parked. Your handset is in
stand-by status.
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
#56=Retrieve call?
[ Select the menu item and confirm.
o Enter the parking position number you have noted.
Note:
If a parked call is not picked up, it returns to the
station from which it was parked after a certain
time (= recall). The following appears on the display "Recalling: (phone no. or name)" or "recalling
from (phone no. or name)”
.
73
Conducting calls – with multiple users
Step by step
Conducting calls – with multiple
users
Call waiting
You need to speak to a user in your communication system urgently, even though his line is busy. You can send
a call waiting signal during his call to let him know you
want to talk to him. The user either answers immediately or you will be automatically connected to him when
he has finished his call.
This function is only available if it has been configured
by the service engineer.
The user is busy. You want to use call waiting.
p
Wait until the message "Camp-on" appears on the display (ringing tone).
You receive a call waiting signal (second call)
You are still available to other callers, even though you
are on the telephone. The call waiting signal informs you
of the second call while you are conducting a call. You
can answer this call without ending the first call.
p
You are on a call and hear a call waiting signal.
If you want to answer the second call, you can either
place the first call on hold (the first caller waits) or end
the first call.
Placing the first call on hold and answering the second call
2ndCall
Answer the second call.
Talk to the second caller. The first caller waits. His call is
on hold. You can now:
• toggle between the two callers (Æ Page 79) or
• set up a conference (Æ Page 80).
74
Conducting calls – with multiple users
Step by step
Ending the second call
either:
Menu
><
Quit and return?
Call the system menu.
[ Select the menu item and confirm.
or:
a Press the On-hook key. The following message appears
on the display: "Recalling". Your handset rings.
c Press the Talk key to talk to the first caller again.
Ending the first call.
a Press the On-hook key. The first call is ended. Your
handset rings.
c Press the Talk key and answer the second call.
Call waiting tone off/on
You can suppress the call waiting tone for external calls.
Deactivating the call waiting tone
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
><
Waiting tone off?
Call the system menu.
[ Select the menu item and confirm.
a Press the On-hook key to end the operation.
Activating the call waiting tone
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
><
Waiting tone on?
Call the system menu.
[ Select the menu item and confirm.
a Press the On-hook key to end the operation.
75
Conducting calls – with multiple users
Step by step
Disabling/enabling automatic call
waiting
You can disable/ enable automatic call waiting signalling
for a second call during a telephone conversation.
Disabling the call waiting tone
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
Call wait. term. off?
[ Select the menu item and confirm.
a Press the On-hook key to end the operation.
Enabling the call waiting tone
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
Call wait. term. on?
[ Select the menu item and confirm.
a Press the On-hook key to end the operation.
Override
You need to speak to an internal user urgently, even
though his line is busy. The "Override" function allows
you to interrupt the ongoing call to pass on a message.
This function is only available when the code has been
input and if it has been configured by the service engineer.
p
The user is busy.
* 6 2 Call the function.
Override
76
o Enter the phone number of the busy user.
Conducting calls – with multiple users
Step by step
<Name>
The override is established. The user name or phone
number, to whom/which the call has been transferred,
is displayed.
Override is ended when you hang up the handset.
Note:
During override
• all users hear an override tone and everything that is said,
• all users see the following message on the
display "Override:....:”.
Transferring a call
Transferring a call means that you wish to hand over a
call you are conducting on your handset to another user.
Transferring
(without announcing the transfer)
p
Menu
><
Start transfer?
You can use this function to forward a call which you answered to another user.
Call the system menu.
[ Select the menu item and confirm.
The current call is placed "on-hold" so that the first user
waits.
o Enter the phone number of the user to whom the call is
to be transferred.
p
The number is dialled.
either:
a Press the On-hook key. The target user’s phone rings.
He picks up the call by lifting the handset.
or:
Menu
><
Transfer?
Call the system menu.
[ Select the menu item and confirm.
a Press the On-hook key. The target user’s phone rings.
He picks up the call by lifting the handset.
77
Conducting calls – with multiple users
Step by step
You receive a recall:
• immediately if you have made a mistake,
• 45 seconds after the transfer if the required user
does not answer.
If you do not answer recalls, another telephone defined
by the service engineer is called (intercept station).
Transferring
(with announcement of call transfer)
p
Menu
><
Start transfer?
You can use this function to forward a call which you answered to another user.
Call the system menu.
[ Select the menu item and confirm.
The current call is placed "on-hold" so that the first user
waits.
o Enter the phone number of the user to whom the call is
to be transferred.
p
The number is dialled. The user answers. You announce
the call presently on hold.
either:
a Press the On-hook key. The user answers the call.
or:
Menu
><
78
Transfer?
Call the system menu.
[ Select the menu item and confirm.
Conducting calls – with multiple users
Step by step
Placing a call on hold
You can interrupt a call temporarily if, forexample, you
want to talk to someone else in the room. The line is
placed "on hold" .
S or
p
Enquiry
You are on a call.
Press the R key or Display key. The current call is placed
"on hold", the user waits.
Resuming the call with the waiting user
either:
Menu
><
Return to held call?
Call the system menu.
[ Select the menu item and confirm.
You are reconnected to the partner.
or:
S Press the R key.
Toggling (switching between calls)
p
Menu
Enquiry
The Toggle function allows you to switch between two
users without allowing them to speak to each other directly. The two users can be either external or internal
users. You can also withdraw from the calls and connect
the two users with each other. You can also start a conference.
You are on a call.
Call the system menu.
Press the display key. The current call is placed "on
hold" , the user waits.
o Enter the phone number of the second user.
p
Toggle
The second user answers.
Press the Display key to switch between the two calls.
When you end a call, the two users are connected with
each other (not possible when both users are external).
79
Conducting calls – with multiple users
Step by step
Conducting a conference
You can connect up to 5 internal or external partners
with each other in a telephone conference. You can include up to 4 external users in the conference.
For information purposes, you will hear a warning tone
every 30 seconds during a conference call (can be disabled - ask your service engineer).
Setting up a conference
You decide to set up a conference while talking to a user.
p
Menu
><
Start conference?
You are on a call and wish to start a conference.
Call the system menu.
[ Select the menu item and confirm.
o Enter the phone number of the new user.
p
Menu
><
Conference?
The user is free and answers the phone. You announce
the conference.
Call the system menu.
[ Select the menu item and confirm.
You and your two partners are connected in a conference call.
Forming a conference
A conference has not yet been set up. However, you
are already connected to two users and are toggling between them. You now want to form a conference involving all partners.
p
Menu
><
Conference?
You are talking to one user.
Call the system menu.
[ Select the menu item and confirm.
You and your two partners are connected in a conference call.
80
Conducting calls – with multiple users
Step by step
Expanding a conference
You can expand an existing conference to include up to
five users.
p
Menu
><
Add party?
Call the system menu.
[ Select the menu item and confirm. Conference is
placed "on hold", the users wait.
o
p
Menu
><
You are connected with two or more partners in a conference call.
Conference?
Enter the phone number of the new user.
The user is free and answers the phone. You announce
the conference.
Call the system menu.
[ Select the menu item and confirm. The new user is included in the conference call.
Ending a conference
p
Menu
><
End conference?
You are connected with two or more partners in a conference call.
Call the system menu.
[ Select the menu item and confirm. The conference is
ended.
Leaving a conference
a Press the On-hook key. You leave the conference.
When one user leaves the conference, the other two
users remain connected.
Viewing the names of conference parties
As the convener of the conference, you can view the
names of all conference parties.
p
You are connected with two or more partners in a conference call.
Viewing the conference parties list
Mnu
><
View conf parties?
Call the additional menu.
[ Select the menu item and confirm. The first party is displayed.
81
Conducting calls – with multiple users
Step by step
> View other parties.
Closing the conference party list
Mnu
><
Exit list?
Call the additional menu.
[ Select the menu item and confirm. The conference party list is closed.
Disconnecting a party from the conference
As the convener of the conference, you can disconnect
users from the conference.
p
Menu
><
View conf parties?
You are connected with two or more partners in a conference call.
Call the system menu.
[ Select the menu item and confirm. The first party is displayed.
> Display the required party.
Mnu
><
Remove party?
Select the menu item and confirm.
[ Select the menu item and confirm. The relevant party is
disconnected from the conference.
Connecting parties
As the conference convener, you can leave the conference and thereby connect the other parties with each
other. If you were previously connected with two or
more parties, the other parties remain in a conference.
Otherwise, the remaining two users conduct a one-toone call.
p
Menu
><
Withdraw?
You are connected with two or more partners in a conference call.
Call the system menu.
[ Select the menu item and confirm. The first party is displayed.
a Press the On-hook key. You leave the conference; the
remaining parties are connected with each other.
82
Conducting calls – with multiple users
Step by step
Using the second call function
The second call is an incoming call that is signalled on
your handset during a call and that can be queried by
you (forexample, Æ Page 74).
A second call can be answered in the following call
states:
• You are on a single call,
• You are on a consultation call,
• You are holding a conference,
• You are on a call which you intend to add to a conference,
• You are toggling between two partners.
Note:
A second call is not signalled via the Bluetooth
headset.
83
Group functions
Step by step
Group functions
Activating/deactivating group calls
If this has been configured by the service engineer, you
belong to one or more groups of internal users that can
be reached at a hunt group or group call phone number.
Calls are signalled on all telephones in the group either
in succession (=hunt group) or simultaneously (=group
call), until a member of the group answers the call. Every user in the group can also remain available under his
own phone number.
You can leave and re-join specific groups or leave and rejoin all groups.
These functions can also be called directly by entering
the relevant code (Æ Page 119).
You belong to a hunt group or group call group
Use this function to leave or re-join the hunt group or
group.
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
either:
><
Leave hunt group?
[ Select the menu item and confirm. You have now left
the hunt group or group.
or:
><
Join hunt group?
[ Select the menu item and confirm. You have now rejoined the hunt group or group.
then:
a Press the On-hook key to end the operation.
84
Group functions
Step by step
You are a member of several groups
Leaving and re-joining individual groups
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
either:
Leave hunt group?
[
Select the menu item and confirm.
or:
><
Join hunt group?
[ Select the menu item and confirm.
then:
>
Group 1
Group 2
Mnu
Select the required group and call the additional menu.
either:
><
Leave hunt group?
[ Select the menu item and confirm. You have now left
the selected group.
or:
><
Join hunt group?
[ Select the menu item and confirm. You have now joined
the selected group.
then:
a Press the On-hook key to end the operation.
Leaving and re-joining all groups
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
either:
><
Leave hunt group?
[ Select the menu item and confirm.
or:
><
Join hunt group?
[ Select the menu item and confirm.
then:
Group 1
Group 2
The list of groups is displayed.
85
Group functions
Step by step
# Press the hash key. You have now left all groups.
or:
* Press the star key. You have now joined all groups.
then:
a Press the On-hook key to end the operation.
86
Group functions
Step by step
Ringing group on
You can have calls to your handset signalled acoustically
on up to five other telephones. The call is received by
the person who answers the call first.
Adding users to a group
First user
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
* 81=
Ringing group on?
[ Select the menu item and confirm.
Mnu
Add ext to group?
Call the additional menu.
[ Confirm.
o Enter the required internal phone number.
Save
Save the settings.
Other users:
Mnu
><
Add another ext?
Call the additional menu.
[ Select the menu item and confirm.
o Enter the required internal phone number.
Save
Save the settings.
a Press the On-hook key to end the operation.
Deleting users
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
* 81=
Ringing group on?
[ Select the menu item and confirm.
<x> in group
The number of parties added is displayed.
87
Group functions
Step by step
Mnu
><
Display/Clear?
Call the additional menu.
[ Select the menu item and confirm. The first user added
is displayed.
> Scroll to the required user.
Mnu
><
Call the additional menu.
[ Select the menu item and confirm. The addition of the
Delete?
first user is cleared.
a Press the On-hook key to end the operation.
UCD (Universal Call Distribution)
This function enables calls to be distributed in a team.
An incoming call is always delivered to the team member who has been idle longest. Team members can also
work in separate rooms, forexample, on the company’s
premises and at a teleworking station. The teams (call
distribution groups) and team members are set up by
the service engineer.
Logging on/off
You must log on and off at the system when you start/
finish work.
Logging on
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
UCD Menu?
[ Select the menu item and confirm.
><
* 401=Log on?
[ Select the menu item and confirm.
o Enter your identifier number (assigned by the service
engineer).
a Press the On-hook key to end the operation.
Logging off
c or d Press and hold down the Talk key or press the Speakerphone key.
88
Group functions
Step by step
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
UCD Menu?
[ Select the menu item and confirm.
><
#401=Log off?
[ Select the menu item and confirm.
a Press the On-hook key to end the operation.
Logging on/off temporarily
You can log on or off at the system temporarily,
forexample, during break times.
Logging on
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
UCD Menu?
[ Select the menu item and confirm.
><
* 402=Log on?
[ Select the menu item and confirm.
a Press the On-hook key to end the operation.
Logging off
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
UCD Menu?
[ Select the menu item and confirm.
><
#402=Not available?
[ Select the menu item and confirm.
a Press the On-hook key to end the operation.
89
Group functions
Step by step
Wrap-up time
If you need more time than the actual call lasts, you can
request/activate a wrap-up time for the last call. This
can be a fixed length of time or, alternatively, you must
deactivate the wrap-up time yourself (log back on).
Requesting time
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
UCD Menu?
[ Select the menu item and confirm.
><
* 403=
Work on?
[ Select the menu item and confirm.
a Press the On-hook key to end the operation.
Logging back on
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
UCD Menu?
[ Select the menu item and confirm.
><
#403=
Work off?
[ Select the menu item and confirm.
a Press the On-hook key to end the operation.
UCD night service
UCD night service is a separate night service for call distribution. It is not affected by the system night service.
All incoming calls are forwarded to a special call distribution destination.
90
Group functions
Step by step
Night destination on
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
UCD Menu?
[ Select the menu item and confirm.
><
* 404=UCD night on?
[ Select the menu item and confirm.
a Press the On-hook key to end the operation.
Night destination off
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
UCD Menu?
[ Select the menu item and confirm.
><
#404=UCD night off?
[ Select the menu item and confirm.
a Press the On-hook key to end the operation.
Checking the number of waiting calls
You can check the number of waiting calls for the group.
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
UCD Menu?
[ Select the menu item and confirm.
><
* 405=Calls in
queue?
[ Select the menu item and confirm.
a Press the On-hook key to end the operation.
91
Group functions
Step by step
Mulap group
(Multiple Line Application)
If your handset’s line belongs to a Mulap group (Multiple
Line Application), then you can
• answer calls for the group (press the Talk key in
group calls)
• make external telephone calls under the group
phone number (the group phone number is stored
in the called party’s caller list, forexample)
• activate and deactivate the group call function for
your handset’s line
• forward the lines of the Mulap group to internal or
external destinations
Activating/deactivating group calls
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
More features?
[ Select the menu item and confirm.
either:
><
#85=Leave hunt
group?
><
* 85=Join hunt
group?
[ Select the menu item and confirm.
or:
[ Select the menu item and confirm.
then:
a Press the On-hook key to end the operation.
Forwarding a Mulap line
You can immediately forward internal and/or external
calls to your lines to different internal or external telephones (destinations) (external destinations are also
possible if the system is configured accordingly).
If you activate call forwarding for a line, this shall apply
to all line keys of your group for this line.
92
Group functions
Step by step
Forwarding on
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
More features:
[ Select the menu item and confirm.
><
* 501=Forward Line:
ON?
[ Select the menu item and confirm.
o Enter a line number.
either:
><
[ Select the menu item and confirm.
1=all calls?
or:
><
2=external calls
only?
[ Select the menu item and confirm.
><
3=internal calls only?
or:
[ Select the menu item and confirm.
o Enter the destination number.
Save
Save the settings.
a Press the On-hook key to end the operation.
Forwarding off
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
More features:
[ Select the menu item and confirm.
><
#501=Forward Line:
Off?
[ Select the menu item and confirm.
o Enter a line number.
a Press the On-hook key to end the operation.
93
Message functions
Step by step
Message functions
The message functions enable you to react to voice
mail/ call back services of the communication system or
of other users or to initiate information features yourself.
Leaving a message/advisory message
A number of advisory messages are stored in your communication system that can be automatically sent to the
caller when an internal call is not answered (in the case
of handsets and telephones with display). These advisory messages can be selected and supplemented in
part by you:
0 = Will return at:
1 = On vacation until:
2 = I am out until:
3 = Out all day
4 = Out to lunch
5 = Not available
6 = Home phone:
7 = Contact:
8 = Avail at:
9 = Am in room:
These advisory messages are standard texts and may
have been changed in your communication system.
Activating an advisory message
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
><
Call the system menu.
[ Select the menu item and confirm.
Advisory msg. on?
either:
><
0 = Will return at:
1 = On vacation until:
[ Select the required advisory message.
If necessary o Expand the message as necessary.
Save
Save the settings.
or:
><
94
Enter message text
[ Select the menu item and confirm.
Message functions
Step by step
o Enter the required advisory message.
Typing errors can be corrected: activate delete mode by
double-clicking the hash key and then use the hash key
to delete a character.
Note:
Forexample, if you want to enter the third character on a key: press the relevant key three times
in succession.
Save
Save the message.
then:
a Press the On-hook key to end the operation.
Deactivating an advisory message
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
><
Absence Text OFF?
Call the system menu.
[ Select the menu item and confirm.
a Press the On-hook key to end the operation.
Sending/calling text messages
You can send short messages to individual internal users or to groups of internal users. These must have a
handset or telephone with display.
These text messages can be selected and supplemented in part by you:
0 = Please callback
1 = Someone is waiting
2 = Appointment
3 = Urgent call
4 = Do not disturb
5 = FAX waiting
6 = Dictation please
7 = Please make copies
8 = Please make coffee
9 = Ready to depart
These text messages are standard texts and may have
been changed in your communication system.
95
Message functions
Step by step
Send a text message
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
><
Call the system menu.
Send Message?
[ Select the menu item and confirm.
Message to:
o Enter the phone number for the required internal user
or the group.
either:
><
0 = Please callback
1 = Someone is wai-
[ Select the required advisory message.
or:
><
Enter message text
[ Select the menu item and confirm.
o Enter the required text message.
Typing errors can be corrected: activate delete mode by
double-clicking the hash key and then use the hash key
to delete a character.
Note:
Forexample, if you want to enter the third character on a key: press the relevant key three times
in succession.
then:
Send
Press the display key.
a Press the On-hook key to end the operation.
Opening an incoming text message
An advisory message appears and the message key
flashes when one or more text messages have been received for you. The date and time of incoming text messages are based on your communication system’s
clock.
f Press the "message list" key.
Msg. from:
...
><
Text
Mnu
Call the additional menu.
[ Select the menu item and confirm. The text message is
displayed.
a Press the On-hook key to end the operation.
96
Message functions
Step by step
Answering a message or voice-mail
message
An advisory message appears and the message key
flashes when one or more information messages or
voice mails have been received for you.
Viewing a new message
either:
f Press the message key.
or:
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
><
Display Messages?
Call the system menu.
[ Select the menu item and confirm.
> [ Select the required message and confirm your selection.
then:
Msg. from:
...
><
Text?
Mnu
[ Select the menu item and confirm.
Mnu
><
Time/date sent?
Call the additional menu.
Call the additional menu.
[ Select the menu item and confirm. The time of the
message is displayed.
either:
Mnu
><
Call Sender?
><
Delete?
Call the additional menu.
[ Select the menu item and confirm. You call back the
sender.
or:
[ Select the menu item and confirm. The entry is deleted.
then:
a Press the On-hook key to end the operation.
97
Message functions
Step by step
Checking for a new voice-mail message
either:
f Press the message key.
or:
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
><
Display Messages?
Call the system menu.
[ Select the menu item and confirm.
o Follow the user guidance system from this point onwards.
a Press the On-hook key to end the operation.
Checking for an old text message
Old messages that have not been deleted cannot be
displayed using the message key f. To call these
messages, proceed as follows:
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
><
>
Display Messages?
Msg. from:
...
Call the system menu.
[ Select the menu item and confirm.
Mnu
Select the required message and call the additional
menu.
><
Text?
[ Select the menu item and confirm.
><
<Text>
Mnu
Time/date sent?
[ Select the menu item and confirm. The time of the
Call the additional menu.
message is displayed.
><
at: ...
Mnu
Call the additional menu.
either:
><
98
Call Sender?
[ Select the menu item and confirm. You call back the
sender.
Message functions
Step by step
or:
><
[ Select the menu item and confirm. The entry is deleted.
Delete?
then:
a Press the On-hook key to end the operation.
Caller list
If you are unable to answer an external and/or internal
call, this call request is stored in a caller list. If you belong to a hunt group or group call group, these call requests are also stored.
Your handset can store up to 10 calls in chronological order. Every call is given a timestamp. The display starts
with the latest call request still not called. When several
calls are received from one caller, the number of calls is
shown.
During a call, you can save the other caller’s phone
number to your caller list.
Note:
If the service engineer has made the appropriate configuration, the phone numbers for all external answered calls are automatically saved.
Selecting a call request
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
><
Caller list?
Call the system menu.
[ Select the menu item and confirm. The first call request
is displayed.
> Select a call request.
99
Message functions
Step by step
Calling back a caller
Mnu
><
Call the menu.
[ Select the menu item and confirm. The connection is
Call?
set up.
Note:
If a connection is established, the user is automatically deleted from the caller list. Call requests for groups (hunt group/group call) are
also deleted if a member of the group has set up
the connection.
If the "Save number?" option is not displayed, all
external incoming calls are automatically saved.
Adding a caller to the caller list
p
Menu
><
Save number?
During a call, you can save the other party’s phone
number in your caller list, forexample, to remind you to
call again later.
Call the system menu.
[ Select the menu item and confirm. The caller’s phone
number is saved.
Deleting a caller from the caller list
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
><
Missed Call List?
Call the system menu.
[ Select the menu item and confirm. The first call request
is displayed.
> Select a call request.
Mnu
><
100
Delete?
Call the menu.
[ Select the menu item and confirm. The call is deleted.
a Press the On-hook key to end the operation.
Additional functions
Step by Step
Additional functions
Handset alarm clock function
When the alarm clock is activated, it rings every day or
every day from Monday to Friday at the set time. The
alarm clock is deactivated during automatic number redial.
Note:
The alarm will only sound with the set melody if
the handset is in idle status. During a call, the
alarm is only signalled by a short tone. Date and
Time must be set.
Prerequisite: The date and time must be set.
Activating the alarm clock
The handset is in idle status.
st
ì
© or w Open the handset’s main menu.
Alarm Clock
[ Select the menu icon and confirm. The input mask for
setting the alarm is displayed.
1 Alarm activation: on/off
1
2
3
4
5
_______Alarm Clock______
Alarm Clock:
f On g
Time:
[HH:MM]
Period:
f Daily g
Volume:
g
f
Melody:
fCircles
”
g
Save
2 Time in format [HH:MM],
forexample, 19:05 = 1905
3 Alarm rings every day or only
Monday - Friday
4 Volume can be set to five different levels + crescendo
ring
5 Adjustable melody
u On v Define settings.
s Move the cursor down one line.
o Enter the time.
s Move the cursor down one line.
... etc.
Save
Save the settings.
101
Additional functions
Step by Step
¼ The alarm clock is activated.
a Press the On-hook key to end the operation.
Deactivating an alarm/repeating after a pause
The alarm rings for 60 seconds. The following appears
on the display: ì. If you do not press anything, the
alarm repeats after five minutes and then deactivates.
During the alarm:
either:
Press the display key. The alarm deactivates.
Off
or:
Snooze
Press the display key or any key. The alarm deactivates
and is repeated after five minutes. The alarm is repeated twice and then permanently deactivated.
Deactivating the alarm clock
The handset is in idle status.
st
ì
© or w Open the handset’s main menu.
Alarm Clock
[ Select the menu icon and confirm. The input mask for
setting the alarm is displayed.
Activation: u Off v Define settings.
Save
Save setting.
a Press the On-hook key to end the operation.
102
Additional functions
Step by Step
Handset appointment reminder
function
You can program your handset to remind you of up to
thirty appointments. The handset must be in idle status
at the time of the appointment reminder. The appointment reminder function is deactivated during automatic
number redial.
The ringer melody and volume are set under Audio Settings/Ringer Settings/Appointments. The date and time
must be set.
Saving an appointment
The handset is in idle status.
st
ç
© or w Open the handset’s main menu.
Calendar
[ Select the menu icon and confirm. The current month’s
calendar is displayed with the current day marked.
uv [ Select and confirm the required day for the new appointment reminder. The input mask for entering a new
appointment reminder appears.
st
New Entry
uv
Appoint.: < On >
[ Select and confirm the menu item or select an existing
appointment entry. The "New Entry" option only appears
if an appointment entry already exists.
Define settings.
s Move the cursor down one line.
Date:
o Enter the date, forexample, 11 November = 1111.
s Move the cursor down one line.
Time:
o Enter the time, forexample, 19:05 = 1905.
s Move the cursor down one line.
Notes:
o Enter the name for the appointment reminder.
X If applicable, delete the old text.
Save
Save the settings.
¼ The appointment reminder function is activated.
a Press the On-hook key to end the operation.
103
Additional functions
Step by Step
Confirming an appointment reminder call
An appointment reminder call is signalled in the same
way as an incoming call.
Off
Press the display key during the appointment reminder
call.
If you do not confirm the appointment reminder call, it
will be stored in a missed dates list.
Deactivating an appointment reminder
The handset is in idle status.
st
ç
© or w Open the handset’s main menu.
Calendar
[ Select the menu icon and confirm. The current month’s
calendar is displayed with the current day marked.
[ Confirm the current day. The list of appointments is displayed.
st
New Entry
11.11, 22:22
11.11, 23:23 ...
[ Select and confirm the appointment reminder that you
want to deactivate.
Options
st
Call the additional menu.
[ Select the menu item and confirm. The appointment re-
Deactivate
minder marked is deactivated.
Save
Save setting.
a Press the On-hook key to end the operation.
Deleting an appointment reminder or the entire list
of appointment reminders
The handset is in idle status.
st
ç
© or w Open the handset’s main menu.
Calendar
[ Select the menu icon and confirm. The current month’s
calendar is displayed with the current day marked.
[ Confirm the current day. The list of appointments is displayed.
st
New Entry
11.11, 22:22
11.11, 23:23 ...
[ Select and confirm the appointment reminder that you
want to delete.
Options
104
Call the additional menu.
Additional functions
Step by Step
either:
st
[ Select the menu item and confirm. The appointment is
Delete Entry
deleted.
or:
st
[ Select the menu item and confirm. A security check
Delete List
question appears.
Yes
Confirm the security check question. The appointment
reminder list is deleted.
then:
Save
Save setting.
a Press the On-hook key to end the operation.
Displaying an unconfirmed appointment
If you have failed to confirm an appointment reminder
call, a Display key is assigned the "Missed Appoint."
function. This unconfirmed appointment must also be
saved in a missed dates list.
Appt.
Display an appointment. The date and time of the unconfirmed appointment are displayed.
Displaying an unconfirmed appointment and unconfirmed anniversaries
Any appointment reminder calls and anniversary calls
you fail to confirm are stored in a missed dates list.
© or w Open the handset’s main menu.
st
st
í Add. Features
Missed Dates
[ Select the menu icon and confirm.
[ Select the menu item and confirm. A list of missed/unconfirmed appointments is displayed. The last appointment missed is always on top and the oldest is last.
st [ Select an unconfirmed appointment or an unconfirmed
anniversary. The relevant information is displayed.
Delete
If applicable, delete the selected appointment.
a Press the On-hook key to end the operation.
105
Additional functions
Step by Step
System appointment function
You can use your handset to enter a single appointment
for the next 24 hours or an appointment that recurs on
a daily basis.
When the appointment is due, your handset rings for
approx. 20 seconds to remind you of your appointment.
The entered appointment appears on the display. This
appointment call is deleted when you confirm it. Alternatively it is deleted automatically after it has been repeated 5 times at one-minute intervals.
This function can also be called by entering the code
(Æ Page 119).
Saving an appointment
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
* 46=Timed reminder
on??
[ Select the menu item and confirm.
Remind at (HHMM):
o Enter the required time.
Note the required data format: Appointment at (HHMM); HH = two-digit hour setting mm = minutes, two
digits For example: 0905 for 9.05 (= 9.05 a.m.) or 1430
for 14.30 (= 2.30 p.m.).
either:
><
One time only?
[ Select the menu item.
or:
><
Daily?
[ Select the menu item and confirm.
then:
Save
Save the settings.
a Press the On-hook key to end the operation.
106
Additional functions
Step by Step
Deleting/ checking entered appointments
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
#46=Timed reminder
off?
[ Select the menu item and confirm.
Reminder at ...
Mnu
Call the additional menu.
either:
><
[ Select the menu item and confirm.
Delete?
or:
><
[ Select the menu item and confirm.
End?
a Press the On-hook key to end the operation.
Confirming an appointment
The handset rings and the appointment is displayed.
c Press the Talk key.
a Press the On-hook key. The appointment is confirmed.
Selecting a base
If your handset is registered at multiple bases, then you
can set a specific base or the base with the best reception as the base to be used. The handset then switches
automatically to this base.
You can change the base name that is displayed on the
handset at any time (Æ Page 34).
st
Ð
© or w Open the handset’s main menu.
H/Set Settings
[ Select the menu icon and confirm.
Handset
[ Select the menu item and confirm.
st
Select Base
[ Select the menu item and confirm.
st
Base 1
...
Best Base
[ Select the required base and confirm. The selected
st
base is ticked.
107
Additional functions
Step by Step
•
•
Base 1 - 4: Select base n to specify the precise HiPath cordless system where the handset is registered.
Best Base: If the handset is registered at multiple
cordless systems, it automatically switches to one
of these systems when it enters the relevant range.
For example: The handset is registered at the Gigaset home base as well as at the cordless system in
the company.
a Press the On-hook key to end the operation.
Speed access to functions and phone
numbers
You can program the left display key and the number
keys 0, 2 to 9 with a phone number or function. You can
then dial the phone number or start the function programmed by simply pressing the appropriate key.
Configuring speed access
either:
0 / 2 ... 9 Press the required number key briefly.
If this key is already programmed with a function, it appears on the left display key. The number key can be
programmed with a new function.
Press the display key.
Set
or:
0 / 2 ... 9 /
?
Press and hold down the required number key or the
left display key.
then: A list of functions that can be programmed on the key
is displayed. The following functions are available for selection:
• Speed dialling
• Call-by-call (Æ Page 52)
• INT
• Alarms (Æ Page 101)
• Calendar
• Bluetooth
st
108
Quick Dial
...
[ Select and confirm the function.
Additional functions
Step by Step
If you selected the "speed dialling" or "call-by-call"
function:
st
Quick Dial
...
[ Select the required phone number and confirm.
Starting a function, dialling a phone number
either:
0 / 2 ... 9 Press and hold down the number key programmed with
the required function. Or press the left display key briefly.
or:
0 / 2 ... 9 Press the number key programmed with the required
function briefly. The function is displayed on the left display key.
Forexample:
Alarm Clock
Press the left display key briefly.
then: Depending on how the key is programmed, the following occurs:
• A phone number from the handset’s telephone directory is dialled.
• A phone number from the call-by-call list is dialled.
• The menu associated with the programmed function is opened.
109
Additional functions
Data exchange between a PC and a handset or
between two handsets
You can transfer data between a PC and your handset or between two
handsets.
Interface overview
The handset supports the following interfaces for data exchange:
Interface
Connect via...
Data transfer between...
Serial V24 interface
Cable (SLIM Lumberg) PC <-> handset
USB interface
Cable (SLIM Lumberg) PC <-> handset
Bluetooth interface
Radio, cordless
PC <-> handset
handset <-> handset
PC application (Gigaset QuickSync)
You can use the PC application, for example, for read and write access to
your handset’s directory as well as download pictures (.bmp) for the
screensaver from the computer to the handset. The PC application must
be installed on your PC for this. It can be downloaded as freeware from the
Internet.
"Data Transfer" is shown on the display during data transfer between the
handset and PC. No inputs are possible via the keyboard when this operation is active and incoming calls are ignored.
The PC application supports different DECT handset types.
For more detailed information, refer to the Gigaset QuickSync help function under: www.siemens.com/GigasetSL370.
110
Additional functions
PC interface (V24, USB)
You can use the PC interface (via a SLIM Lumberg cable) to read, modify
and transfer phonebook entries and pictures to the mobile phone.
Configuring the PC interface
To configure the PC interface, you must:
1. use a Siemens data cable (Æ Page 127) to connect the headset/PC interface jack on the handset to the computer.
2. install the PC application.
For more information, consult your system administrator.
Data transfer mode
Certain functions necessitate the transfer of large volumes of data between the handset and the computer. When these functions are selected,
the handset switches to data transfer mode and "Data Transfer" appears on
the display. In this mode, no inputs are possible via the keyboard and calls
are ignored.
The handset is switched to data transfer mode by:
• activating read/write access to the phonebook
• loading screensavers
The handset automatically switches to idle if a fault occurs in the
course of transferring data.
•
•
•
•
•
111
If Bluetooth is activated, for example, disconnecting the data cable at the connection jack deactivates this feature.
If a Bluetooth voice connection is in progress, Bluetooth only deactivates after it ends.
If a Bluetooth data connection is in progress, activation/deactivation depends on the peer
Bluetooth automatically reactivates when the accessory is removed.
Bluetooth activation is impossible if this feature is deactivated
when the accessory is connected..
Additional functions
Step by Step
Bluetooth interface
If you have installed a Bluetooth interface on your PC,
you can also communicate with the PC application via
the Bluetooth interface on your handset.
Note:
Theoretically, third parties can tap Bluetooth connections.
Transferring a phonebook from handset to handset
via Bluetooth
Prerequisite: The Bluetooth interface on the other
handset (Æ Page 114) must be active.
If the Bluetooth connection is not yet established between the handsets, perform the following steps:
On your handset
© or w Open the handset’s main menu.
st
í
st
Data Transfer
[ Select the menu icon and confirm.
st
Bluetooth
[ Select the menu item and confirm. The Bluetooth menu
st
Search Data Device
st
Found Devices
SL3 professional
Add. Features
[ Select the menu icon and confirm.
is displayed.
[ Select the menu item and confirm. The handset searches for a Bluetooth data device and sets up a wireless
connection. The name of the devices found are displayed.
Select the required device, for example, the other handset.
Options
Open the handset’s menu
st
Trust Device
[ Select the menu item and confirm.
st
agreed PIN:
[ Enter the Bluetooth PIN and confirm (default: 0000).
112
The device is recorded in the list of known devices.
Additional functions
Step by Step
On the other handset:
[ Enter the Bluetooth PIN immediately and confirm (de-
st
agreed PIN:
st
Add to
Trusted Device
list?
fault: 0000). If you were not fast enough, repeat the previous steps.
[ Confirm the prompt.
The Bluetooth connection is established. The two handsets can now exchange data in vCard format.
Transferring data
s Open the phonebook.
t s Select the entry.
© or w Open the handset’s phonebook menu.
either:
st
Copy List
[ Select the menu item and confirm.
or:
st
Copy Entry
[ Select the menu item and confirm.
then:
st
vCard via Bluetooth:
[ Select the menu item and confirm.
st
Trusted Devices
...
[ Select and confirm the target device or handset. The
vCard data is sent to the target device.
Now follow the instructions on your handset display.
113
Additional functions
Step by Step
Deactivating and activating the Bluetooth interface
You can deactivate the Bluetooth interface of you do not
need it for extended periods of time. This increases
your handset’s stand-by time.
Deactivating the interface
© or w Open the handset’s main menu.
st
í Add. Features
[ Select the menu icon and confirm.
st
Data Transfer
[ Select the menu icon and confirm.
st
Bluetooth
[ Select the menu item and confirm. The Bluetooth menu
st
Activation Õ
is displayed.
[ Select the menu item and confirm. The Bluetooth interface is deactivated.
Õ The check box is not marked if the Bluetooth function is
deactivated.
Activating the interface
Follow the procedure described above to activate the
Bluetooth interface.
The active Bluetooth function is ticked.
114
Telephone blocking
Step by step
Telephone blocking
Handset telephone lock
You can protect your handset against unauthorised access by entering a 4-digit numerical code to lock it.
The PIN is preset to "0000" (default). The handset does
not prompt for a PIN in this setting. As soon as you have
changed the PIN you will need to enter it when you turn
on the handset.
Enter the value "0000" again to deactivate the PIN.
Attention:
If you have forgotten your PIN, please contact
Siemens Service. The PIN will be reset at your
own expense.
Entering a new PIN
st
st
st
Ð
© or w Open the handset’s main menu.
H/Set Settings
[ Select the menu icon and confirm.
Handset
[ Select the menu item and confirm.
Change HSPIN
[ Select the menu item and confirm.
o
Enter the old PIN. If a PIN has not yet been set, then enter "0000".
o
Enter the new PIN.
o
Repeat the new PIN.
s Move the cursor down one line.
[ Confirm your entries.
a
Press the On-hook key to end the operation.
Battery charging when PIN lock active
If the handset deactivates because the battery pack is
flat, it automatically reactivates as soon as you place it
in the charging shell. The charging operation starts. If
you have already set a PIN, you must enter it so that the
handset can receive calls.
115
Telephone blocking
Step by step
Telephone lock code programming
You can protect your handset against unauthorised access (thereby safeguarding personal data) by entering a
5-digit code to lock and unlock it.
c or d
Menu
To change a code, first enter the old code and then key
in the new code twice.
Press and hold down the Talk key or press the Speakerphone key.
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
* 93=Change PIN?
[ Select the menu item and confirm.
o Enter the old code (5 digits, default "00000").
o Enter the new PIN, forexample, 11111 (5 digits).
o Repeat the new PIN.
a
Press the On-hook key to end the operation.
Note:
If you have forgotten your PIN, contact your
service engineer for help. He will be able to reset your PIN to "00000".
It is also possible to open your mobile phone
from a central station, forexample, from the attendant terminal.
116
Telephone blocking
Step by step
Locking/unlocking the handset
You can lock your handset to prevent external dialling
and programming, thereby preventing unauthorised
use in your absence, forexample.
Prerequisite: You have defined a personal code or use
the default code "00000".
Locking the handset
c or d
Menu
><
Changeover on?
Press and hold down the Talk key or press the Speakerphone key.
Call the system menu.
[ Select the menu item and confirm.
o Enter the PIN code (5 digits, default "00000").
a
Press the On-hook key to end the operation.
Note:
Even though it is locked, you can still use your
handset to answer external calls and make internal calls. When an external connection is established, the following message appears on the
display "Telephone Lock Active".
Your handset can also be locked from a central
station (Æ Page 116).
Unlocking the handset
c or d
Menu
><
Changeover off?
Press and hold down the Talk key or press the Speakerphone key.
Call the system menu.
[ Select the menu item and confirm.
o
Enter the PIN code (5 digits, default "00000").
a Press the On-hook key to end the operation.
117
Telephone blocking
Step by step
Central telephone lock/locking/
unlocking other handsets
If you have the appropriate authorisation, you can lock
and unlock other handsets to prevent unauthorised use.
If the user has locked his handset and has forgotten the
individual password he has set, you can unlock the
phone again using this function.
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
><
Service?
[ Select the menu item and confirm.
><
More features?
[ Select the menu item and confirm.
><
* 943=Telephone
Lock?
[ Select the menu item and confirm.
o Enter a user’s phone number.
either:
* Lock the handset. The following appears on the display:
"Telephone locked".
or:
# Unlock the handset. The following appears on the display: "Telephone unlocked".
118
System functions
Step by step
System functions
The system functions can be called up via the menu or
directly by entering codes.
Calling functions via the menu
c or d Press and hold down the Talk key or press the Speakerphone key.
Menu
Call the system menu.
either:
><
[ Select and confirm the function.
Suppress call ID?
or:
><
Service?
[ Select the menu item and confirm.
><
* 41=Temporary
MNS?
[ Select and confirm the function.
or:
><
Service?
[ Select the menu item and confirm.
><
More functions?
[ Select the menu item and confirm.
><
#58=View callbacks?
[ Select and confirm the function.
then:
a Press the On-hook key to end the operation.
Calling functions via codes
c or d Press and hold down the Talk key or press the Speakerphone key.
either:
* o Enter code according to table (Æ Page 120).
or:
# o Enter code according to table (Æ Page 120).
then:
a Press the On-hook key to end the operation.
119
System functions
Functions and codes
Functions
Codes
Automatic call wait.term.on
* 490
Automatic call wait.trm.off
Waiting tone off
Waiting tone on
Call waiting
# 490
* 87
# 87
* 55
Caller list
- Call
- Save phone number
Advisory msg. on
Advisory msg. off
DND on
DND off
# 82
* 82
* 69
# 69
* 97
# 97
UCD:
- Log on
- Log off
- Work on
- Work off
- Available
- Not available
- UCD night on
- UCD night off
- No. of calls
Override (authorised telephone only)
FWD for MULAP on
FWD for MULAP off
Speaker call
Call trace
* 401
# 401
* 403
# 403
* 402
# 402
* 404
# 404
* 405
* 62
* 501
# 501
* 80
* 84
120
System functions
Functions
Codes
Temporary phone
* 508
Messages
- Send
- View sent message
* 68
# 68
Conference:
- on
- off
Call Charge Display
Use speed dialling
Change Speed Dial
Toggle
Tone dialling
Night Service ON
Night Service OFF
*3
#3
* 65
*7
* 92
*2
* 53
* 44
# 44
Park
– Park call
– Retrieve call
Account code
Callback
View callbacks
Suppress phone number
Temporary phone number (MSN)
Restore phone number
Ringing group on
Ringing group off
Hunt group/join hunt group
Hunt group/leave hunt group
Control Relay On
Control Relay Off
121
* 56
# 56
* 60
* 58
# 58
* 86
* 41
# 86
* 81
# 81
* 85
# 85
* 90
# 90
System functions
Functions
Codes
Change PIN
* 93
Recall to Network (flash)
Language selection
Changeover on
Changeover off
Directory (system, LDAP)
Tel. data service
Timed reminder on
Timed reminder off
Door release ON
Door release OFF
Door opener
Pickup group
Pickup, directed
Forwarding on
Forwarding off
Trunk FWD on
Trunk FWD off
Forwarding after timeout off
Forwarding after timeout on
Telephone Lock
Return to held call
* 51
* 48
* 66
# 66
* 54
* 42
* 46
# 46
* 89
# 89
*61
* 57
* 59
*1
#1
* 64
# 64
# 495
* 495
* 943
*0
122
Appendix
Appendix
Troubleshooting
Some malfunctions can be resolved without outside intervention. The following table provides a list of such malfunctions. All other malfunctions
should be reported to the relevant service personnel.
Error
Possible cause
Remedy
No display.
Handset not switched
on.
Press the On-hook key
until confirmation is
received.
The battery pack is flat. Charge or replace the
battery pack.
You cannot dial a
phone number.
The handset is locked. Unlock the handset.
No reaction to keystroke.
Keypad lock activated.
Press the hash key until
confirmation is received.
The key is stuck.
Release the key.
De-crescendo tone
sequence during
input.
An incorrect entry was Repeat key sequence
made.
while watching the display; where applicable,
consult the operating
instructions.
The line "Base n"
flashes (n= 1 - 4).
The handset is outside Come closer to the base
the base radio range;
radio range, change your
radio signals too weak. position.
Handset not registered. Register the handset.
Intervals between syn- Switch off the handset
chronisation attempts and switch it back on
are too long.
again.
No ringer on the hand- Ringer is deactivated.
set.
Activate ringer.
"Do Not Disturb" is acti- Deactivate "Do Not Disvated.
turb".
Nothing audible during a call.
123
The "R key" was
pressed – the microphone and the receiver
inset are muted.
Press the "Delete" display key to re-activate
the microphone and the
receiver inset.
Appendix
Error
Possible cause
Remedy
The following appears Communication sysimmediately after the tem is being used by
Talk key is pressed:
other users.
Connect.
No dial tone available;
no calls can be made.
Repeat call later.
The following,
Handset is blocked.
forexample, appears:
Base 1
Outgoing and incoming calls and activation/
deactivation are not
possible.
Remove the battery pack
from the handset and
then re-insert it. Proceed as when loading
batteries for first time
(Æ Page 18).
The following appears: Maximum input time
Time exceeded
was exceeded.
Avoid long pauses
between keystrokes.
The On-hook key was
not pressed.
Press the On-hook key.
The following appears: The communication
Please try later
system is overloaded.
Wait and try again later.
The following appears: Function is currently
Currently not acces- not available.
sible
Wait and try again later.
The following appears:
Not possible
or:
Incorrect input
or:
Nothing stored
No connection available under the phone
number dialled.
Enter the phone number
correctly or call the
attendant console.
Speed dial number not
available, appointment
entered incorrectly,
entry blocked or not
allowed, prerequisite
not fulfilled
(forexample, if there is
no second partner for
toggling), number
dialled was incomplete.
Correct your input,
select a permitted
option, enter the phone
number in full.
The following appears: Blocked function was
Not authorized
called.
Apply to the relevant
service personnel for the
COS for the blocked
function.
The following appears: Incorrect PIN was
Not allowed
entered.
Enter the correct PIN.
124
Appendix
Error
Possible cause
Remedy
The following appears: Phone number was not Enter the phone number
Not available
fully entered, the star or correctly or as prehash key was not
scribed.
pressed.
The following appears: Data transfer is active. Wait and try again later.
Do not disturb
Cleaning the handset
Removing everyday dirt
To clean the handset and the charging shell, simply wipe them with a damp
or anti-static cloth. Never use a dry cloth.
Do not use abrasive cleaning agents.
After contact with liquids
1. Deactivate the handset immediately. Do NOT activate it!
2. Remove the battery pack immediately. Leave the battery compartment
open.
3. Allow the liquid to drain off:
– Hold the handset in a horizontal position with the open battery compartment facing down.
– Hold the handset in a vertical position with the open battery compartment facing down. Shake the handset gently, tilting it slightly back
and forth.
– Dab all components dry and then leave the handset in a warm spot
(not beside a microwave, oven, etc...) for at least 72 hours with open
battery compartment and keypad facing down.
The handset can be put back into operation once it is completely dry.
Storage
To avoid damage, the handset should not be stored with sharp objects,
such as, knives or tools, etc. We recommend keeping the handset in a protective pouch when in use (Æ Page 127).
125
Appendix
Documentation
These operating instructions can be found in PDF format at the following
URL:
http://www.siemens.com/hipath
and on CD-ROM (ask the service personnel) in HTML and PDF format.
To view or print the operating instructions in PDF format, you need a computer on which the free Adobe Acrobat Reader program is installed.
To view the operating instructions in HTML format, you need a computer
with a Web browser, forexample, Microsoft Internet Explorer.
Technical data
Maximum sound pressure level
according to TBR10, Annex D:
less than 118 dB (A)
Operating and charging times:
Æ Page 19
Permissible ambient conditions
for operation:
+5 °C to +45 °C
20 % to 75 % relative humidity
Weight incl. battery pack:
approx. 93 g
Original battery pack:
Lithium-Ion, 700 mAh,
V30145-K1310-X250
V30145-K1310-X322
V30145-K1310-X401
Dimensions (W x H X D):
approx. 46,5 x 114 x 22,6 mm
Charging shells
Gigaset SL3 Charger EU
EU
S30852-H1982-R141
Gigaset SL3 Charger UK
UK
S30852-H1982-L141
Gigaset SL3 Charger LAM
LAM
S30852-H1982-U141
Gigaset SL3 Charger AUS
AUS
S30852-H1982-C441
126
Appendix
Accessories
Only use original accessories. This will help you avoid injury and property
damage and you can ensure that all relevant regulations are observed.
Headset:
Headsets from different manufacturers may be used
Data cable
Data cable DCA-500:
To connect the handset to the serial
RS232 interface on your computer
Data cable USB DCA-510:
To connect the handset to the USB
interface on your computer
Source
For information on accessories (such as, headsets, data cables, protective
pouches), contact Siemens at the following address:
Siemens AG, I&S IS SC S RC, Tübingerstr. 1-5, 80686 Munich
Mr. Jens Schwabe
Tel.: +49 89 9221 - 3174
Fax: +49 89 9221 - 6603
E-mail: jens.schwabe@siemens.com
EU guidelines
The handset and accessories listed conform to the following EU guideline:
99/05/EC "Radio and Telecommunication Terminal Equipment“
127
Appendix
Declaration of conformity
Your handset is supplied for use within a specific country, which is displayed on the underside of the device. Country-specific features must be
observed.
The device complies with the basic requirements of the R&TTE Directive
and therefore displays the CE marking.
Extract from original declaration
"We, Siemens AG, declare, that the above mentioned product is manufactured according to our Full Quality Assurance System certified by CETECOM ICT Services GmbH with the registration number "Q810820M" in
compliance with ANNEX V of the R&TTE Directive 99/05/EC. The presumption of conformity with the essential requirements regarding Council
Directive 99/05/EC is ensured."
Senior Approvals Manager
The Declaration of Conformity (DoC) has been signed. In case of need, a
copy of the original DoC can be made available via the company hotline.
0682
128
Index
Index
A
Accessories ............................................... 127
Activating ....................................................... 2
Advisory message ..................................... 94
Advisory tones ............................................ 24
Alarm .......................................................... 101
Allocating ..................................................... 77
Ambient conditions .................................. 126
Anonymous calling ..................................... 62
Answering a message .............................. 97
Answering a voice mail ............................. 97
Answering an information message ....... 97
Answering calls .......................................... 62
Appointments
Activating ............................................... 103
Checking ................................................ 107
Confirming ..................................... 104, 107
Deactivating .......................................... 104
Deleting .................................................. 107
Displaying .............................................. 105
Entering .................................................. 106
Handset ~ .............................................. 103
System ~ ............................................... 106
Attachment clip
Fitting ....................................................... 19
Audio functions .......................................... 22
Auto answer ............................................... 30
Automatic call waiting ............................... 76
Automatic number redial .......................... 43
Available memory ...................................... 57
B
Base
Changing the Name Displayed ............ 34
Selecting ................................................ 107
Battery pack
Capacity ................................................... 19
Charging ............................................... 2, 18
Charging time ......................................... 19
Inserting ................................................... 16
Operating time ........................................ 19
Permitted ~ ............................................. 19
Stand-by time .......................................... 19
Talk time .................................................. 19
Warning tone .......................................... 38
Battery tone
Setting ...................................................... 24
Bluetooth ..................................................... 40
Bluetooth interface .................................. 112
C
Call answering group ................................... 8
Call charge display ..................................... 64
Call charges ................................................. 64
Call forwarding .............................................. 9
Call forwarding to a fixed destination ....... 9
Call pickup group .......................................... 8
Call trace ...................................................... 65
Call waiting .................................................. 74
Automatic ~ ............................................ 76
Call waiting tone off/on ............................. 75
Callback .......................................................... 5
Call-by-call list ............................................. 52
Caller list ...................................................... 99
Calls
Accepting ................................................... 7
Anonymous ~ ......................................... 62
Answering ................................................. 7
Directed transfer .................................... 62
Making ....................................................... 3
Dial a phone number ............................ 3
Picking up .................................................. 8
Rejecting .................................................... 8
Capacity ....................................................... 19
Central telephone lock ............................ 118
Changing a phone number ....................... 55
Charge status .............................................. 18
Charging time ............................................. 19
Cleaning ..................................................... 125
Clip
Fitting ....................................................... 19
Code programming .................................. 116
Colour scheme, setting ............................. 33
Computer .................................................. 111
Conference .................................................. 80
Connecting parties ................................. 82
Disconnecting ......................................... 82
Ending ...................................................... 81
Expanding ................................................ 81
Leaving ..................................................... 81
129
Index
Setting up ................................................ 80
Viewing .................................................... 81
Confirmation tone
Function ................................................... 38
Setting ...................................................... 24
Connecting parties ..................................... 82
Connection jack ........................................... IV
Connection quality ....................................... 2
Consultation (second line) .......................... 6
Contrast, setting ......................................... 33
Control key ............................................. IV, 12
Control relay ................................................ 68
Copying the phonebook ............................ 58
D
Data cable .................................................. 111
Data transfer ............................................. 111
Date, setting ............................................... 31
DDIA with speed dialling .......................... 46
Deactivating .................................................. 2
Declaration of conformity ....................... 128
Default state ............................................... 37
Deleting
Call-by-call list ......................................... 57
Entry ................................................... 43, 57
Phonebook .............................................. 57
Redial list ................................................. 43
Dialling
A phonebook entry ................................ 54
After line seizure ...................................... 3
Before line seizure ................................... 3
Preparation ................................................ 3
Dialling a number ....................................... 54
Dimensions ............................................... 126
Directed answering of calls ...................... 62
Directed assignment of an MSN ............. 60
Directed transfer of calls .......................... 62
Display .......................................................... IV
Colour scheme ....................................... 33
Contrast ................................................... 33
Lighting .................................................... 34
Screensaver (screen picture) ............... 32
Settings .................................................... 32
Display keys ........................................... IV, 13
Display lighting ........................................... 34
Do not disturb ............................................. 63
130
Door release
Activating ................................................. 66
Deactivating ............................................ 66
E
Entering codes .......................................... 119
Entrance telephone ................................... 65
Entry
Changing .................................................. 55
Deleting .............................................. 43, 57
Dialling ............................................ 4, 43, 54
Marking as VIP ........................................ 56
Saving ....................................................... 53
Searching for ........................................... 55
Viewing .................................................... 55
Entry, sending ............................................. 58
EU guidelines ............................................ 127
Everyday dirt ............................................. 125
External call forwarding ............................. 69
F
Function keys .............................................. 11
Functions and codes ............................... 120
G
Group call
Activating/deactivating .......................... 84
Group functions .......................................... 84
Guidelines .................................................. 127
H
Handset
Locking/unlocking ................................. 117
Locking/unlocking, other ~ ................. 118
Handset operating times .......................... 19
Hash key ................................................. IV, 11
Headset ....................................................... 40
Hunt group .................................................. 84
I
Icons ............................................................. 15
Identification code ...................................... 60
Individual system speed dialling .............. 47
Index
Interface ............................................ 111, 112
Interference with electronic equipment
EMC ........................................................... II
J
Jack for headset/PC interface ................... IV
K
Key tones
Function ................................................... 38
Setting ...................................................... 24
Keypad lock ................................................. 10
Keys
Control key .............................................. 12
Display keys ............................................ 13
Function keys .......................................... 11
L
Language setting
Handset ................................................... 20
System ..................................................... 21
LDAP telephone database ........................ 49
Leaving the radio network/
re-registering ........................................... 10
Line seizure ................................................... 3
Liquids ....................................................... 125
List, sending ............................................... 58
Locking/unlocking the telephone .......... 117
M
Mailbox function ........................................ 94
Main menu .................................................. 15
Making calls .................................................. 3
Making calls with the headset ................. 40
Manual number redial ................................. 4
Memory ....................................................... 57
Menu icons ................................................. 15
Message
Answering ............................................... 97
Leaving ..................................................... 94
Message functions .................................... 94
Message key ............................................... IV
Message list ............................................... 11
Messages .............................................. 94, 95
Microphone .................................................. IV
MSN ....................................................... 60, 69
Mulap group
Deactivating/ activating group calls ..... 92
Forwarding
Activating ............................................. 93
Deactivating ......................................... 93
Forwarding a line .................................... 92
Multiple subscriber number ............... 60, 69
N
Night service ............................................... 71
Number keys ............................................... IV
Number redial
Adding a phone number ....................... 44
Automatic ................................................ 43
Deleting an entry/list .............................. 43
List ........................................................ 4, 43
Manual ....................................................... 4
Number, applying ....................................... 54
O
On hold ........................................................ 79
On/off key ............................................... IV, 11
On-hook key ........................................... IV, 11
Opening/closing battery compartment .. 17
Override ....................................................... 76
P
Parking ......................................................... 73
Parts of the device ...................................... IV
PC interface .............................................. 111
Permitted battery packs ........................... 19
Phone number
Changing .................................................. 55
Dialling ........................................................ 3
Dialling from the phonebook ................ 54
Saving ....................................................... 53
Suppressing ............................................ 62
Phonebook
Handset ~ ................................................ 52
LDAP ........................................................ 49
System ~ ................................................. 48
131
Index
Phonebook entries, sorting ...................... 54
Phonebook, copying .................................. 58
Picking up a call ............................................ 8
PIN .................................. 2, 115, 116, 117, 118
Placing a call on hold ................................. 79
Prefixes, converting ................................... 36
Programming keys ................................... 108
Project code ................................................ 60
Protective cover ......................................... 16
Protective pouch ...................................... 125
Suffix-dialling/DDIA ................................ 46
System ..................................................... 46
System (individual) ................................. 47
Stand-by time ............................................. 19
Star key ................................................... IV, 11
Storage ....................................................... 125
Suffix-dialling with speed dialling ............ 46
Switching between calling parties .......... 79
System speed dialling ............................... 46
System speed dialling, individual ............ 47
R
T
R key ................................................. IV, 11, 12
Radio range ................................................... 2
Range problems ........................................... 2
Recall ...................................................... 73, 78
Receiver inset .............................................. IV
Rejecting a call ............................................. 8
Reset ............................................................ 37
Resource directory .................................... 26
Ringing ......................................................... 23
Ringing group on ........................................ 87
Talk key ................................................... IV, 11
Talk time ...................................................... 19
TDS telephone data service ..................... 67
Technical data ........................................... 126
Telephone blocking .................................. 116
Telephone conference .............................. 80
Telephone lock ................................. 116, 118
Telephone volume ..................................... 22
Temporary phone ....................................... 61
Text message ............................................. 96
Time, setting ............................................... 31
Toggle .......................................................... 79
Tone dialling ................................................ 72
Tones ..................................................... 23, 24
Transfer ........................................................ 77
Transferring ................................................. 77
Transferring a call ....................................... 77
Troubleshooting ....................................... 123
S
Saving a phone number ............................ 53
Second call .................................................. 83
Second line ................................................. 61
Second line (consultation) .......................... 6
Sending
Entry ......................................................... 58
List ............................................................ 58
Sending a signal to the network .............. 69
Setting the ringer ....................................... 23
Setting the screen picture ........................ 32
Setting the screensaver ............................ 32
Siemens Data Suite ................................. 111
SMS .............................................................. 96
Sorting phonebook entries ....................... 54
Sound pressure level, maximum .......... 126
Speaker volume ......................................... 22
Speakerphone key ................................ IV, 11
Speakerphone mode ................................. 39
Speed access to functions ..................... 108
Speed dialling
Call-by-call key ......................................... IV
Dialling ...................................................... 55
132
U
UCD night service ...................................... 90
Universal call distribution .......................... 88
V
vCard ...................................................... 52, 58
Converting prefixes ................................ 36
Vibration alert .............................................. 25
VIP ................................................................ 56
Volume ......................................................... 22
Index
W
Warning tone ........................................ 29, 80
Function ................................................... 38
Wrap-up time .............................................. 90
133
Copyright © Siemens Enterprise
Communications GmbH & Co. KG 08/2007
Hofmannstr. 51, D-81359 München
Reference No. A31003-G2100-U105-1-7619
The information provided in this document contains
merely general descriptions or characteristics of performance which in case of actual use do not always
apply as described or which may change as a result
of further development of the products. An obligation to provide the respective characteristics shall
only exist if expressly agreed in the terms of contract.
Subject to availability. Right of modification reserved. The trademarks used are owned by
Siemens Enterprise Communications
GmbH & Co. KG or their respective owners.
www.siemens.de/enterprise