Whynter ARC-08WB Instruction manual

Service Questions: Contact Whynter at 866-WHYNTER
Sales Inquiries: Contact Sylvane at 1-800-934-9194
WHYNTER ECO-FRIENDLY 8,000 BTU PORTABLE AIR CONDITIONER
MODEL# : ARC-08WB
Instruction Manual
Congratulations on your new WHYNTER product. Please read this Instruction Manual carefully
before using this product to ensure proper operation. Keep this manual in a safe place for future
reference.
TABLE OF CONTENTS
INTRODUCTION / DISPOSAL INFORMATION
3
SAFETY PRECAUTIONS / OPERATING CONDITION
4-5
IDENTIFICATION OF ACCESSORIES
6
IDENTIFICATION OF PARTS
7
CONTROL PANEL
8
INSTALLATION INSTRUCTIONS
9 - 12
OPERATION INSTRUCTIONS
13 - 14
WATER DRAINAGE
15
REMOTE CONTROL
16
CARE AND MAINTENANCE
17
TECHNICAL DATA
18
TROUBLESHOOTING
19 - 20
WARRANTY INFORMATION
21
2|Page
Thank you for choosing the Whynter portable air conditioner. Please follow the instructions
provided in this user guide to obtain the very best performance from your portable air
conditioner and take full advantage of the many features your portable air conditioner offers
you. We trust that your Whynter air conditioner will provide the performance and reliability
that we stand for.
Please keep this user manual in a safe place for future reference.
DISPOSAL
This symbol on the product or its packaging indicates that the appliance cannot be treated as
normal domestic trash, but must be handed in at a collection point for recycling electric and
electronic appliances. Your contribution to the correct disposal of this product protects the
environment. Further information about the recycling of this product can be obtained from
your local municipal authority.
3|Page
Your safety and the safety of others are very important to us.
To reduce the risk of fire, electrical shock or injury when using your appliance, follow these basic precautions.
SAFETY PRECAUTIONS
Before the appliance is used, it must be properly positioned and installed as
detailed in this manual.



















Do not under any circumstances cut or remove the third (ground) prong from the power cord
Make sure this unit is connected to a correctly grounded power supply outlet. Do not use an
extension cord or power strip
The power cord is UL listed. It has a built-in L.C.D.I. (leakage, current, detection, interruption)
circuit breaker for added safety. If the power supply is interrupted, press the reset button to
reconnect the unit to power source
It is recommended to use a separate circuit that its size should be 15 Amps for the air conditioner
Do not use an excessively wet cloth, industrial solvents, oil-based products to clean this portable
air conditioner
To avoid the risk of shock, the product should never be used in bathrooms, shower rooms, or in
any other steamy or wet areas
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliances
Do not repair, disassemble and/or modify the unit by yourself
Always turn off the portable air conditioner when cleaning the air filter, and transporting
Do not turn this unit on and off by plugging and unplugging. Always use the ON/OFF switch
Transport the unit in an upright position only, or leave it in an upright position for at least 4 hours
before first use
Ensure curtains or other objects are not obstructing the air inlet filters
Do not bend or crush the exhaust hose while in use
Always allow at least 20” of clearance around the unit for ventilation. Do not use this unit inside
closets, cabinets and/or cramped spaces between furniture
This unit is optimized to operate in an ambient temperature of 64°F – 90°F
This unit must be installed in an area protected from the element, such as wind, rain, water spray
or drips
The unit should not be located next to ovens, grills or other sources of high heat
Always place the unit on even and hard and level surface
Do not sit or place objects on the unit
4|Page










Do not allow children to climb, stand or hang on the appliance. The air conditioner could tip
over and get damaged and/or seriously injure somebody
Keep fingers out of the air intakes and air outlets
The appliance is an electrical appliance. To avoid injury from electrical shock do not operate it
with wet hands, while standing on a wet surface or while standing in water. Do not use it in
outdoors or in wet conditions
When positioning or moving the appliance, ensure it is not turned upside down or greater
than 45° or more off level
This appliance is designed for household, non-commercial use only. Any other use will void
the warranty
Do not plug into the power outlet before set up is completed
Do not operate this unit without the air filter(s)
Do not use harsh chemicals to clean the filter(s). Dry thoroughly before inserting the filter(s) into
the unit
Do not add extra length to the exhaust hose by more than a total length of 9’. This will
reduce the cooling efficiency of the portable air conditioner
At the end of each season, all water must be drained from the unit and filter(s) must be
cleaned before storage
THE MANUFACTURER DISCLAIMS ANY RESPONSIBILITY IF THE ABOVE INSTRUCTIONS
ARE NOT FOLLOW ED.
OPERATING CONDITION
MODE
ROOM TEMPERATURE
COOL
Higher than 62°F / 17°C
DRY
Higher than 54°F / 13°C
Your portable air conditioner is supplied with a Leakage-Current
Detection and Interruption (LCDI) plug. This plug reduces the risk of
fire due to arcing faults in the power supply cord. Please follow the
instructions below to ensure that LCDI plug works properly.
1. Plug the power cord to a grounded wall outlet. Do not plug to
a power strip or extension cord.
2. Press the TEST button on the plug. This should trip the plug
and cut the power to the air conditioner. If the plug does not
trip and the unit comes on, please contact technical support.
3. Press the RESET button to start the air conditioner.
4. Do NOT use the TEST and RESET buttons to turn the air
conditioner on and off.
5|Page
IDENTIFICATION OF ACCESSORIES
IMAGE
ACCESSORY NAME
QUANTITY
Exhaust hose, Sliding Round Adaptor
and Flat Mouth Adaptor
1 set
Window sliders and Clear plastic plug
(plug is in the upper corner of the
plastic bag that holds the user manual)
1 set
Foam seal
3 pcs
Remote control & Batteries
1 set
Drain hose
1 pc
Activated Carbon filter
1 pc
6|Page
IDENTIFICATION OF PARTS
Front
1. Control Panel
2. Front Air Vent / Louvers
3. Handles
4. Remote Signal receptor
5. Panel
Rear
6. Upper air filter
7. Air outlet (hot air exhaust)
8. Casters
9. Upper air intake
10. Upper drain port
11. Lower air intake (Compressor)
12. Lower air filter
13. Lower drain port
7|Page
OPERATING YOUR AIR CONDITIONER
Before you begin, thoroughly familiarize yourself with the control panel, remote control and all of
the functions. Follow the symbol for the desired function. The unit can be controlled by the unit
control panel alone or with the remote control.
CONTROL PANEL
1. MODE
Controls the 4 function modes: COOL, DRY
(DEHUMIDIFY), FAN, and AUTO
5. TIMER
Turns the timer function on and off. To cancel the
timer, press the On-Off button or set the timer to 0.0
6. FAN
Controls the 3 fan speeds: HI, LOW & AUTO. The
fan speed indicator lights illuminates to show the
set fan speed. When the AUTO speed is selected,
none of the fan speed indicator illuminates.
2. SLEEP
Turns the sleep function on and off.
3. UP & DOWN
Adjusts set temperature (1°C/ 2°F increments) or
timer hours (0 – 24 hours).NOTE: This unit is
capable of displaying set temperature in Fahrenheit
or in Celsius. To convert from one to the other, press
and hold the Up and Down buttons for 3 seconds
4. ON-OFF
Turns the unit on and off.
7. LED DISPLAY
In Cool mode: shows set temperature in °C or °F
and AUTO timer setting.
In DRY and FAN only modes: shows room
temperature.
Error Codes:
E1, E2 & E4: Unplug unit and restart in 5 minutes.
P1: Bottom water tank is full; drain water from the
unit
NOTE: When more than one codes occur, the
priority of the code display order is:
E4--E2--E1--P1.
8|Page
INSTALLATION INSTRUCTIONS
The air conditioner should be placed on a hard and level surface strong enough to support the
unit. The unit has casters and it should only be rolled on smooth, flat surfaces. Use caution
when rolling on carpet surfaces. Do not attempt to roll the unit over objects. Never place any
obstacles around the air inlet or outlet and allow at least 20 inch of clearance for efficient airconditioning.
Cool or Auto Mode
Dehumidify or Fan Mode
Install Hose
Remove Hose
Exhaust Hose Installation
When you use this air conditioner unit, hot air must be
exhausted out of the room to complete the air exchange
of the condenser. When the unit is operating in
Dehumidify or FAN only mode, no exhaust is required.
1. Pull out about 6” of one end of the exhaust hose.
2. Install the flat mouth and sliding round exhaust
connector on the exhaust hose by turning counterclockwise. See Fig. 16 and 17
3. Push in the exhaust hose into the air outlet port at the
back of the unit. See Fig. 18
4. Only extend the exhaust hose to the necessary
length. We do not recommend extending the exhaust
hose more than 8' long. If you are interested in
purchasing an additional 4’ exhaust hose please
contact info@whynter.com for retail sales information.
NOTES:
 The duct can be compressed or extended moderately according to the installation
requirement, but it is desirable to keep the exhaust hose length to a minimum.
 Do not bend the exhaust hose
 Make sure that there are no obstructions around the air outlet of the exhaust hose in order for
the exhaust system to work properly
Air filter Installation
Your Whynter portable air conditioner is equipped with a
washable Pre-Filter and an Activated Carbon Filter. The
washable air filter removes large particles such as dust,
pet hair and dander.
The Activated Carbon filter is designed to remove
smoke and other odors. It is recommended you replace
the Activated Carbon filter every 2-3 months or as
needed.
WARNING: NEVER OPERATE THE AIR
CONDITIONER WITHOUT THE AIR FILTER
9|Page
Activated Carbon filter
Upper Filer
Window kit Installation
When you use this air conditioner unit, hot air must be exhausted out of the room to complete
the air exchange of the condenser. When the unit is operating in dry or fan only mode, no
exhaust is required.
Your window kit has been designed to fit
most standard vertical and horizontal
windows.
However, it may be necessary for you to
modify the installation procedures for your
window. Please refer to Fig. 6 & Fig. 7 for
minimum and maximum window openings.
NOTE:
If your window opening is less than the
mentioned minimum length of the window
slider kit, cut the slide bar with hole to fit
window opening. Never cut out the hole on
the window slide bar.
When using the window kit on a window or
sliding door it will cause the window or
sliding door not to be properly closed and
locked. Additional security measurements
maybe needed.
The window slide bars can be fixed with
the clear plastic bolt. See Fig. 7a
10 | P a g e
Window kit Installation in a double-hung window
1. Open window or sliding door for approximately 5”
2. Cut the foam seal (adhesive type) to the proper
length and attach it to the bottom of the
window. Fig.10.
3. Adjust the length of the window bars to the same
length and width of the opening of the window.
Cut the window piece if necessary to fit the
length of your window. Fig. 11.
4. Close the window on the window slide bars. For
long term installation, you may screw the window
kit into your window frame. Fig. 12.
5. Cut the foam seal to the length and seal the
open gap between the top window sash and
outer window sash. Shown in Fig.13.
11 | P a g e
Window kit Installation in a sliding door/ window
1. Open window or sliding door for approximately
5”
2. Cut the foam seal (adhesive type) to the proper
length and attach it to the bottom of the door /
window. See Fig.14.
3. Adjust the length of the window bars to the
same length and width of the opening of the
window. Cut the window piece if necessary to fit
the length of your window. See Fig. 15.
4. Close the door/ window on the window slide
bars. For long term installation, you may screw
the window kit into your window frame. See Fig.
16.
5. Cut the foam seal to the length and seal the
open gap between the top window sash and
outer window sash. See Fig.17.
12 | P a g e
OPERATION INSTRUCTIONS


BEFORE USING YOUR APPLIANCE
Remove the exterior and interior packing
Before connecting the appliance to the power source, let it stand upright for approximately
4 hours. This will reduce the possibility of a malfunction in the cooling system from
handling during transportation
SWITCHING ON/OFF THE AIR CONDITIONER
 The appliance can be switched ON or OFF by pressing the On-Off button on the control
panel or the On/Off button on the remote control
COOLING MODE
 In this mode, the air conditioner cools and dehumidifies the room. To activate this function
mode, press the MODE button until the COOL indicator light comes on. When the cooling
mode is set, the compressor will start in approximately 3 minutes. In cooling mode, hot air is
exhausted from the outdoor exhaust port and the exhaust hose must be connected to
exhaust out the hot air
 The temperature setting range of this air conditioner is from 62°F / 17°C to 88°F / 30°C. To
set the temperature, press the UP or DOWN buttons. This air conditioner has a 5°F
temperature cushion which if the set temperature is within 5°F of the ambient temperature,
the unit runs on fan only mode. This saves energy and prolongs the life of the compressor of
the air conditioner
 To set the fan speed, press the FAN button. In cooling mode, the difference in noise level
between the 3 fan speeds is not very noticeable when the compressor is on. Try setting the
unit to Fan only mode, you should be able to hear the difference between high and low fan
speed settings
DRY (DEHUMIDIFYING) ONLY MODE
 In this mode, the air conditioner only dehumidifies the room, the compressor will activate
intermittently depending on the ambient temperature and the fan speed is set to LOW.To
activate this function mode, press the MODE button until the DRY indicator light comes on.
Please note that when switching function mode, there will be an approximately 3 minute
transition time. In dehumidifying mode, do not connect the exhaust hose and let the warm
air return to the room
AUTOMATIC MODE
 When you set the air conditioner in AUTO mode, it will automatically select cooling or fan
only operation depending on what temperature you have selected and the room temperature
is close to the unit. The fan speed is automatically selected and cannot be changed
 To operate the unit in Auto mode when the unit is on, press the Mode button until the
indicator for “Auto” is lit
FAN ONLY MODE
 In this mode, only the fan of the air conditioner runs and circulates the air in the room. To
activate this function mode, press the MODE button until the FAN indicator light comes on.
In this function mode, the temperature cannot be set. Subsequently, set the desired fan
speed by pressing the FAN button. Fan Only mode requires that the exhaust hose be
removed
13 | P a g e
TIMER (DELAYED SWITCH ON / OFF) FUNCTION
 This function mode enables a delayed switch ON or delayed switch OFF of the
air conditioner. The time (hours) delay can be set, enabled and disabled
SETTING SW ITCH OFF TIMER
With the air conditioner operating in any function mode, press the TIMER button. The TIMER
OFF light will come on. Then set the desired time delay OFF hours by pressing the UP and
DOW N buttons. The time increments are at 0.5 hour to up to 10 hours, followed by 1 hour
increment up to 24 hours. When the delay time set has elapsed, the air conditioner switches off.
To cancel the delayed switch off function, turn off the air conditioner or adjust the time setting to
0.0.
SETTING DELAYED SWITCH ON TIMER
With the air conditioner is off, press the TIMER button. The TIMER ON light will come on. Then
set the desired time delay ON hours by pressing the UP and DOW N buttons. The time
increments are at 0.5 hour to up to 10 hours, followed by 1 hour increment up to 24 hours.
When the delay time set has elapsed, the air conditioner switches on. To cancel the delayed
switch on function, turn on the air conditioner or adjust the time setting to 0.0.
SLEEP MODE
In this mode, the air conditioner gradually increases the set temperature in cooling mode,
decreases the noise level and conserves energy. In Sleep & cooling mode, the set temperature
is increased by 1°C/ 2°F in the first 30 minutes. The temperature will then increase by another
1°C/ 2°F after an additional 30 minutes. This new temperature will remain the same for 7 hours.
To activate this function mode, press the SLEEP button until the sleep indicated light comes on.
AUTO RESTART
In the event of a power outage, the air conditioner restarts at the previously set function mode
and settings when power is restored.
CONTROLLING THE AIR FLOW DIRECTION
The louvers can be adjusted manually. To adjust the air flow direction, manually move the louvers
to the desired position. The maximum setting angle is about 60°.
NOTE: Keep the louver fully opened during operation.
NOISE LEVEL
Portable air conditioners may make sounds that are not familiar to you. The sounds listed below
are normal. Noise reflecting off hard surfaces such as a floor or wall can make the sounds seem
louder than they actually are.
 The compressor may make a pulsating or high-pitched sound
 Water running from the evaporator to the water tank may make a splashing sound
 Refrigerant flowing may make a gurgling sound
 Fan sound may come from front and back air vents
14 | P a g e
WATER DRAINAGE
When the water level of the bottom tray reaches
maximum level, the unit will beep 8 times and the
digital display will show P1 symbol. Also, the
cooling or dehumidifying function will stop and the
fan only function will start.
Continuous drainage
In COOL or DRY modes, remove the upper
drain plug from the back of the unit and install
the drain water hose (5/8 universal female
mender) with ¾” hose (can be purchased
locally).
If this part is unavailable from your local
hardware store, just attach the drain hose to the
drain firmly. The hose will fit snug which should
prevent any leaking. Place the open end of the
hose directly over the drain area in your
basement floor. Please refer to Fig.21 & 22.
Manual drainage
Carefully move the unit to a drain location,
remove the bottom drain plug and let the water
drain (See Fig. 23). The P1 symbol will
disappear and the cooling or dehumidifying
function can be started. Be sure to reinstall the
bottom drain plug before using the unit.
15 | P a g e
REMOTE CONTROL
The portable air conditioner can be switched on by the remote control. To transmit signals from
the remote control to the air conditioner, point the front part of the remote handset towards the
control panel on the air conditioner. Reception of the signal is confirmed by a beep. The
maximum signal transmission distance is approximately 8 meters / 26 feet.
NOTE:
 Other appliances in the same room controlled by a remote control (TV, radio, stereo, etc.),
may cause interferences
 Electronic and fluorescent lamps may interfere with the signal transmissions between the
remote control and the air conditioner
 Remove the batteries if the remote control is not used for long periods
INSTALLING BATTERIES
 Only use two dry LR03 AAA 1.5V Batteries (included) in the remote control
 Always change both batteries at the same time
To insert the batteries, open the flap on the back of the remote control by sliding if off. Strictly
adhere to the polarity signs on the bottom of the battery housing, close the flap once the batteries
have been inserted.
INDICATOR
1 – Mode Indicator
2 – Lock Indicator
3 – Temp./Timer Display
4 – Fan (High)
5 – Fan (Low)
6 – Timer Indicator
7 – Up Button
BUTTONS
8 – Down Button
FUNCTION
Displays the current selected mode
(Auto, Cool, Dry or Fan)
Indicates unit is on Lock mode
Displays temperature or timer setting
Displays the selected high fan speed
Displays the selected low fan speed
Indicates Timer mode activated
Increases set temperature/time
FUNCTION
12 – Sleep Button
13 – Timer On Button
14 – Reset Button
15 – Timer Off Button
16 – Lock Button
Decreases set temperature/time
Controls the 4 function modes:
Auto, Cool, Dry & Fan
Turns the unit On and Off
Controls the 3 fan speeds: High & Low
or Auto
Enables Sleep mode
Enables the On timer & set timer hours
Cancels all settings
Enables the Off timer & set timer hours
Locks all settings
17 – LED Display Button
Turns on and off the display light
9 – Mode Button
10 – On/Off Button
11 – Fan Speed Button
16 | P a g e
CARE AND MAINTENANCE
IMPORTANT:
 Switch off the air conditioner and disconnect the plug from the power outlet
 Drain water by removing the drain plug
 Always transport the air conditioner in an upright position only
CLEANING THE AIR FILTERS
 To ensure the air intake is filtered properly and
to assure that your air conditioner runs
efficiently, it is recommended to clean the air
filters at least once every two weeks
 This unit has two pre-filters; the upper and the
lower filters
 Switch off the air conditioner and pull out the
upper and lower air filter from the unit by
following the arrow directions shown.
 Use a vacuum cleaner or tap lightly to remove
loose dust and dirt from the filters. Then rinse
them thoroughly under warm or cold running
water (no hotter than 100F.)
 Dry thoroughly before re-inserting the filters
CLEANING THE AIR CONDITIONER
 Always switch off the air conditioner and disconnect the plug from the power supply outlet before
cleaning the air conditioner
 Use a soft damp cloth to wipe the body of the unit.
 Never use harsh chemicals, oil-based products, detergents, chemically treated cloths or other
cleaning solutions. These could possibly damage the body of the air conditioner
END OF SEASON STORAGE
 Switch off the air conditioner and disconnect the power plug from the power supply outlet before
cleaning the air conditioner
 Clean the air filters
 Drain the condensed water completely
 On a warm day, turn on the Fan only mode for half a day so that the inside can dry out
completely
 Wrapped the power cord and bundle it with the tape
 Remove the batteries from the remote controller
 Disconnect the exhaust hose
 It is recommended that the air conditioner be put back into its original carton for storage
17 | P a g e
Service Questions: Contact Whynter at 866-WHYNTER
Sales Inquiries: Contact Sylvane at 1-800-934-9194
TECHNICAL DATA
Cooling capacity
8,000 BTU cooling capacity
Power supply
115 V / 60Hz
Maximum power input
910W
Maximum input
8.2 Amps
Dehumidifying capacity
45.6 Pts/day
Thermostat
62° - 88°F (17°C - 30°C)
Refrigerant
R410A
Air flow (max.)
270m3/h /159CFM
Fan speeds
3 (LOW and HIGH or AUTO)
Exhaust hose length
59” / 5’
Unit Dimensions
13.25" D x 13.75" W x 29" H
Unit W eight
47.5 lbs
18 | P a g e
TROUBLESHOOTING
Problem
The portable air
conditioner does not
turn on
Possible Causes
 Power failure / outage
 The automatic switch, line
fuse, or breaker has been
tripped
 The power supply voltage is
too low
 The power cord is damaged
 The L.C.D.I. power plug for
the unit is tripped
 The internal water reservoir
is full and ‘P1” appears on
display
The unit turns on but
the compressor does
not turn on (the fan runs
but the unit is not
cooling)
 The room temperature is
outside of the operational
tolerances of the unit
 The Cooling mode is not on
 The compressor has not
turned on yet because of its
time delay
 The set temperature is too
high
 The internal water reservoir
is full and ‘P1” appears on
display
The air coming out of
the unit is not very cold,
or the airflow volume is
weak
 The filters are dirty or
obstructed
 The air intake or exhaust is
obstructed
 The unit is set in DRY or
FAN mode
 The unit is set to low fan
speed
19 | P a g e
Solutions
 Restore the power supply
 Flip the switch / change the fuse / turn the
breaker back on. Also note that you may have
too many appliances drawing power on one
circuit, you may need to move the other
appliances to another circuit
 Move the unit onto another circuit with the
correct voltage
 Call for service. Only authorized personnel
should replace damaged power cord or power
plug
 Press the Reset button on the L.C.D.I. power
plug
 Drain water from the air conditioner
 Possible loose internal connection. Please
contact Whynter for service
 This unit is designed to work in ambient
temperatures of 64°F to 90°F
 Press the MODE button until the COOL light is
shown on the display
 Give the compressor 3 minutes to turn on after
the Cooling mode has been selected
 Set the air conditioner to a lower temperature.
It is recommended to set the temperature to at
least 5°F of the ambient temperature
 Either manually drain the water by removing
the drain plug or allow the unit to exhaust the
water itself by running the fan only mode.
Then cooling will resume
 Possible loose internal connection. Please
contact Whynter for service
 Clean the air filters
 Make sure there is at least 20" of clearance
from the air intake. Make the length of the
exhaust hose is as short as possible
 Set the unit to the cooling mode
 Set the unit to a higher fan speed
Problem
The unit has worked for
a long time, but the
room is not cold enough
Possible Causes
Solutions
 Windows or doors are open
 Close all windows and doors
 There are too many people
in the room
 You may need additional cooling or
another air conditioner
 There is direct sunshine into
the room
 Close curtains or blinds and try to
minimize the amount of direct sunlight into
the room
 The room is a kitchen or with
many heat-producing
appliances
 You may need additional cooling or
another air conditioner
 There is a server in the room
 The room is too large
The unit is very noisy
The unit leaks water
 The unit is not level
 The surface underneath the
unit is uneven
 Move the unit to a location with a level and
hard floor
 Low power voltage
 Make sure the wall outlet and support the
required power consumption of the air
conditioner and do not use an extension
cord
 The unit is tilted or not
leveled
 Make use the unit is leveled
 The water tank is full
Fan speed cannot be
changed
 You may need additional cooling or
another air conditioner
 You may need additional cooling or
th
i
diti
 Make sure the unit is on hard, level and
stable surface
 Fan speed differences are
not very noticeable
20 | P a g e
 Drain water from the drain plug at the
back of the air conditioner
 The fan speed difference is not very
noticeable when the compressor is on. Try
setting the unit to Fan only mode, you
should be able to hear the difference
between high and low fan speed settings
ONE YEAR LIMITED WARRANTY &
THREE YEAR WARRANTY ON COMPRESSOR
This W HYNTER portable air conditioner is warranted, to the original owner within the 48
continental states, for one year from the date of purchase against defects in material and
workmanship under normal use and service. Should your W HYNTER portable air conditioner
prove defective within one year from the date of purchase, return the defective part or unit,
freight prepaid (within two months of purchase; after two months to one year, customer will be
responsible for freight cost to Whynter’s service department), along with an explanation of the
claim to Whynter LLC. Please package the portable air conditioner carefully in its original
packaging material to avoid damage in transit. Please retain the original box and packaging
material. Under this warranty, W hynter will repair or replace any parts found defective. This
warranty is not transferable. After the expiration of the warranty, the cost of labor and parts will
be the responsibility of the original owner of the unit.
THIS W ARRANTY DOES NOT COVER:
 Acts of God, such as fire, flood, hurricanes, earthquakes and tornadoes.
 Damage, accidental or otherwise, to the air conditioner while in the possession of
a consumer not caused by a defect in material or workmanship;
 Damage caused by consumer misuse, tampering, or failure to follow the care and
special handling provisions in the instructions.
 Damage to the finish of the case, or other appearance parts caused by wear.
 Damage caused by repairs or alterations to the product by anyone other than
authorized by the manufacturer.
 Freight and Insurance cost for the warranty service.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR
REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST
PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. WHYNTER SHALL NOT BE LIABLE FOR CONSEQUENTIAL
OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY
BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE- QUENTIAL DAMAGES, OR LIMITATIONS ON
THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS
WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM
STATE TO STATE.
To obtain service or information, contact
Whynter LLC via email at service@whynter.com or call
1-866-WHYNTER.
Product contents and specifications may change without notice.
Copyright © 2014 Whynter LLC
www.whynter.com