Mitsubishi Electric JT-SB216JSH-H-E Instruction manual

1109875HD4001
GB
Hand dryer
MODEL
JT-SB216JSH-W-E Heater Model
JT-SB216JSH-H-E
JT-SB216JSH-S-E
JT-SB216KSN-W-E Heater-less Model
Model Name Display
Position
Appliance handling
differs depending
on the model.
Therefore, be
sure to check the
model name of your
appliance.
Appliance color -W(White), -H(Dark grey), -S(Silver)
For User
INSTRUCTION MANUAL
■ Read this manual thoroughly before use to ensure the appliance is used safely and correctly.
After reading the manual, store it in an easily accessible location for future reference.
■ Be sure to check the "Date of Purchase" and "Name of Vendor" on the warranty certificate, and store it in a safe
place.
You should not attempt to install the appliance yourself. (The safety and functionality of the appliance cannot be guaranteed.)
This product is intended for the purpose of drying hands and is not covered by the warranty if used for any other purpose. It has
no sterilizing or disinfecting functions.
INDEX
Safety Precautions ……………………………………………… 2
■ Names of Parts ……………………………………………………… 3
How to use the appliance ……………………………………… 4
■ Turning the power on ……………………………………………… 4
■ After washing hands ………………………………………………… 4
■ If not using for a long period ……………………………………… 4
Maintenance ……………………………………………………… 5
1.Switching the power OFF before cleaning ……………… 5
2.Cleaning the appliance exterior and hand drying area … 5
3.Cleaning the air filter ………………………………………… 6
4. Draining and cleaning the drain tank……………………… 6
5.Cleaning the drain pipe …………………………………… 7
If you think something has gone wrong ……………………… 8
Specifications …………………………………………………… 9
■ Drying times for different modes (approximate) and uses ……… 9
−1−
Safety Precautions
Warning
The following may lead to death or serious
personal injury if handled incorrectly
Do not modify or disassemble the appliance.
Doing so may cause fires, electric shocks or injury.
Do not open the front panel
Doing so may result in an electric shock.
Prohibited
Do not use in the
bathroom/
shower room
Do not allow the
appliance to get wet
o not use at locations where salt damage may occur, or
D
where corrosive, neutral, or reductive gases are present.
The above may cause fire, electric shocks or malfunctions.
Follow
instructions

Note
Follow
instructions
Do not allow water to get on the appliance.
This may cause electric shocks or malfunctions.
◦ When changing the installation place, consult
your dealer or installer.
There is a risk of injury.
Use single-phase 220-240V power.
Using the incorrect power supply may cause fires,
electric shocks or malfunctions.
Do not use in a shower room or other locations with a
great deal of humidity in the air, or where condensation
may form on the appliance.
This may cause electric shocks or malfunctions.
Caution
Prohibited
Do not
disassemble
◦ Use exclusive wiring
Using this appliance with other devices on a branch
socket may cause abnormal heat, which may cause fires.
◦Always turn off the power switch during
maintenance work.
Failure to do so may result in an electric shock.
The following may lead to injury or damage to
property if the appliance is handled incorrectly.
This appliance is not intended for use by young
children or infirm persons unless they are
adequately supervised by a responsible person to
ensure that they can use the appliance safely.
Young children should be supervised to ensure
that they do not play with the appliance.
Do not use for drying anything other than hands.
Inappropriate use may cause an accident.
◦ Always use the appliance with the drain tank, air
filter, and side covers attached.
Any water entering the appliance may cause short
circuits, electric shocks or damage.
Follow
instructions
◦ Wear rubber gloves when cleaning the appliance.
Not doing so may result in injuries.
If the appliance stops working or if a malfunction
occurs, turn off the power switch and groundfault circuit interrupter before contacting your
dealer for an inspection and repairs.
Failure to do any of the above may result in electric
shocks or short circuits, or fires due to short‑circuiting.
Do not use in the following locations.
Locations where the temperature could be lower than 0ºC. Locations where there is a lot of dust.
Outdoors
Locations where the temperature could be higher than 40ºC. Locations where there is a lot of condensation.
Locations where salt damage may occur. Vehicles (including ships and airplanes)
Locations where the appliance is in direct or strong sunlight (May cause the sensor to malfunction)
Near food or tableware. Locations where the appliance may come into direct contact with water. Kitchens
(Where there is a risk of water splashing.)
Locations where corrosive, neutral, or reductive gases are present.
(This may shorten the working life of the appliance and/or cause malfunctions.)
Rooms that have a sterilization basin, swimming pools, bathrooms.
Do not use with chemicals on your hands.
(This may damage the surface of the appliance, or cause discoloration or cracking.)
Be sure to completely wipe off any detergents or chemicals on the appliance.
(Failure to do so may damage the surface of the appliance, or cause discoloration or cracking.)
Only use the specified cleaning agents.
(For details on detergents, see the "Maintenance" section.)
If water is sucked into the appliance, it may cause damage to the mechanism, or moisture may be absorbed into the
soundproofing material, allowing bacteria to breed. Therefore, do not allow water to come in contact with the air filter or air duct.
−2−
■ Names of Parts
※ Shaded areas in the figure indicate antibacterial material.
Hand drying area
Black wall area
Power control section
Switch door
r
Powe
ON
OFF
Blue light
Main unit
Power switch
Sensor
The blue light does not have a
sterilizing effect.
Do not look directly into the blue light.
Drain tank
Side cover
Air filter
Display
Heater type
(JSH)
Power
Power lamp
Heater-less type
(KSN)
Power
Power lamp
−3−
Heater
Heater lamp
Check
Check lamp
How to use the appliance
■ Turning the power on
NOTE
How to open
Power
switch
Power
ON
OFF
Do not turn the power on
while hands or other objects
are inside the hand drying
area.
■ After washing hands
1
2
Wet hands
3
Insert hands from the side
4
Bring hands upwards
※ Repeat 2-3 times
Automatic Stop Function All models
The power lamp flashes and the dryer stops automatically if the appliance is used continually for more than
30 seconds. To continue using the hand dryer, remove your hands, and then re-insert them.
Simple heater
JT-SB216JSH type only (not applicable to JT-SB216KSN)
Softens the feeling of cold air.
If the room temperature is above 30ºC, the heater will stop working to prevent the temperature from
rising too high.
NOTE
If the room temperature is less than 18ºC, the air may feel cold.
■ If not using for a long period
Turn the power switch "OFF".
−4−
Maintenance
Caution
Warning
◦ Wear rubber gloves when cleaning the appliance.
Not doing so may result in injuries.
Always turn off the power switch during maintenance work.
Failure to do so may result in an electric shock.
Do not allow water to get on the appliance.
This may cause electric shocks or malfunctions.
Cautions
Only use cleaning products that are labeled as safe "Safe to use on plastics".
Do not use any of the following cleaning materials
(They may damage the surface of the appliance, or cause discoloration or cracking.)
Solvents such as thinner or benzene
Acid, alkaline or chlorine detergents
Mold and mildew removers
Citrus-based or other plant-based detergents
Antiseptics
Nylon scourers or abrasives
Do not clean the front cover of a silver appliance with alcohol.
(This may damage the surface of the appliance, or cause discoloration or cracking.)
※ "Alcohol" means a disinfectant with an ethanol content of 83% or less.
※ Be sure to dispose of any alcohol that has collected in the drain tank.
※ Do not spray alcohol directly onto the appliance.
Damage to the appliance (such as rusting) is not covered by the warranty if the above cautions are not
observed.
NOTE
1
When cleaning the appliance, use a neutral detergent. (pH: 6-8)
The exterior of the appliance can be wiped with alcohol. (Excluding the front cover of silver models)
After cleaning with neutral detergent or alcohol, be sure to wipe away all remaining traces of the detergent or alcohol.
After wiping the appliance clean with alcohol, be sure to dispose of any alcohol that has collected in the drain tank.
※ Do not spray alcohol directly onto the appliance.
When using a chemical cloth, be sure to follow the instructions carefully.
Switching the power OFF before cleaning
1.Open
Adjusting air speed and heater
– see installation manual page 10
2.Turn the power OFF
NOTE
Do not turn the power on
while hands or other objects
are inside the hand drying
area.
Power
switch
Power
ON
OFF
Hand drying area
2
Cleaning the appliance and hand drying area
Black wall area
If it is particularly dirty
Wipe with a well-wrung wet cloth
Sensor
Front cover
NOTE
−5−
After cleaning with neutral detergent or alcohol,
be sure to wipe away all remaining traces of the
detergent or alcohol.
Clean the sensor area about once a week.
Cleaning the air filter
3
Around once a week
Remove the drain tank
and air filter
Tap gently by hand
Use a vacuum
Reinstall the drain tank and
cleaner to remove air filter
dust

or
Drain tank
Handle Air filter
NOTE
If the air filter is particularly dirty, clean it with warm or cold water.
After washing the air filter with water, dry it thoroughly.
Cautions
4
Never dry the air filter using a heat source such as flames or a dryer.
This may damage the filter or cause fires.
Ensure that the air filter is fitted properly.
Dirt and dust may get into the appliance and shorten its working life if the air filter is out of position.
Draining and cleaning the drain tank
Before it fills up (at least once a week)
Remove the drain tank
Empty the water, and wash the lid and
drain tank.
Attach the lid
Click


Reinstall the drain tank
Drain tank
NOTE
Empty the drain water at least once a week before the drain water exceeds the full
line.
Full line
Cautions
Empty the drain tank regularly.
If the drain tank is not emptied it will start to smell, and the drain water may leak onto the floor causing the
floor to become dirty.
Ensure that the drain tank is fitted properly.
−6−
5
Cleaning the drain pipe
At least once a week
Hook your fingers into the handle on the
side cover, and pull it diagonally upwards
Wipe the inside of the side cover and
drain pipe with a well-wrung wet cloth
Drain collection
outlet
Drain pipe
Drain hole
Handle
Side cover (inside)
NOTE
Drain
collection
outlet
Gently wipe any dirt from the drain using a soft cloth.
Do not pour water directly onto the drain pipe.
Drain pipe
After cleaning, attach the side cover.
Cautions
Ensure that the side cover is fitted properly.
−7−
If you think something has gone wrong
Perform the following checks and fixes.
Problem
No air blows even if
hands are inserted
Check
Fix
Are any lamps in the display on?
Has a blackout occurred?
Turn the ground-fault circuit interrupter on.
Turn the power switch "ON".
Are you putting your hands in all the way?
Place your hands all the way inside the hand drying area.
Was the power switched turned on while your hands
or an object was inside the hand drying area?
Turn the power switch "OFF", and when the
display lamps all go out, remove any foreign
substances or dirt. Wait for at least 1 minute
after turning the power switch "OFF", and then
turn it back "ON" again.
Is the sensor blocked by dirt or dust?
Air does not stop
Is the black wall area in the hand drying area white with dirt?
Stops operating
during hand drying
Has the dryer been used continually for
more than 30 seconds?
Are any lamps in the display flashing?
If the hand dryer is used continually for more than 30 seconds,
the power lamp flashes, and the dryer automatically stops.
To continue using the hand dryer, remove your hands, and
then re-insert them.
The heater lamp is off.
(Only for JT-SB216JSH type)
Contact the dealer about any changes to the
settings. Costs are as agreed with the dealer.
Air conditioning is not working.
The air may not feel warm if the room temperature is less than
18ºC.
(The JT-SB216KSN type is not equipped with a simple heater)
Check the model name of the product.
The JT-SB216KSN model is not equipped with an
internal heater, and therefore hot air does not blow.
Is the room temperature too high?
If the room temperature is above 30ºC, the heater will stop
working to prevent the temperature from rising too high.
The lamp does not
light up even when the
power is switched on.
Has a blackout occurred?
The ground fault circuit interrupter is
"OFF".
Turn the ground-fault circuit interrupter on.
The display section
lamp flashes
This may flash if there is a malfunction
in the power supply.
Turn the power switch "OFF", check that all of the
lamps on the display section are off, and then wait
for 1 minute before switching the power back "ON".
Crack-like shapes can be
seen around the nozzle
There is no unevenness, even when touched by hand.
(No feeling of cracking)
This pattern occurs when the product is molded (manufactured).
It does not affect product performance, and is not a malfunction.
Air is cold
Air does not
warm up
The operating sound is too
loud (Air blow is too strong)
I want to reduce power consumption
(want to turn off the heater)
(Only for JT-SB216JSH model)
Contact your dealer for any changes
to settings or adjustments etc.
Costs are as agreed with the dealer.
Cautions
Do not attempt to modify or
disassemble this appliance yourself.
If the above fixes do not work, turn off the power and the ground-fault circuit interrupter, and have
your dealer inspect and if necessary repair the appliance. (Costs are as agreed with the dealer.)
−8−
Specifications
Model
Voltage
JT-SB216JSH ※
JT-SB216KSN
Frequency Power Input (W) Current (A)
220-240V
50-60Hz
The values above are when the air volume is "high". 1240
5.7 - 6.2
550
3.0 - 3.2
Weight (kg)
Dimensions (WxDxH)
11
300 × 219 × 670 (mm)
The drain tank capacity is 0.8ℓ.
※
With simple heater.
■ Drying times for different modes (approximate) and uses
Mode
※
Drying times (approximate) ※
JT-SB216JSH
JT-SB216KSN
Noise
Use
HIGH
9~11secs
̶
approx. 61dB
To dry hands quickly
STANDARD
11~13secs
12.5~14.5secs
approx. 58dB
To achieve both quick drying and low noise
Drying times are based on Mitsubishi measurements. (50mg of water per hand)
−9−
Information on Disposal
Note: This symbol mark is for EU countries only.
This symbol mark is according to the directive 2002/96/EC Article 10 Information for users and Annex IV,
and/or to the directive 2006/66/EC Article 20 Information for end-users and Annex II.
English
Your MITSUBISHI ELECTRIC product is designed and
manufactured with high quality materials and components which
can be recycled and/or reused.
This symbol means that electrical and electronic equipment,
batteries and accumulators, at their end-of-life, should be
disposed of separately from your household waste.
If a chemical symbol is printed beneath the symbol shown
above, this chemical symbol means that the battery or
accumulator contains a heavy metal at a certain concentration.
This will be indicated as follows:
Hg: mercury (0,0005%), Cd: cadmium (0,002%),
Pb: lead (0,004%)
In the European Union there are separate collection systems for
used electrical and electronic products, batteries and
accumulators.
Please, dispose of this equipment, batteries and accumulators
correctly at your local community waste collection/recycling
centre.
Please, help us to conserve the environment we live in!
Deutsch
Ihr MITSUBISHI ELECTRIC-Produkt wurde unter Einsatz von
qualitativ hochwertigen Materialien und Komponenten
konstruiert und gefertigt, die für Recycling und/oder
Wiederverwendung geeignet sind.
Dieses Symbol bedeutet, dass elektrische und elektronische
Geräte sowie Batterien und Akkus am Ende ihrer
Nutzungsdauer von Hausmüll getrennt zu entsorgen sind.
Wenn ein chemisches Symbol unterhalb des oben abgebildeten
Symbols erscheint, bedeutet dies, dass die Batterie bzw. der
Akku ein Schwermetall in einer bestimmten Konzentration
enthält. Dies wird wie folgt angegeben:
Hg: Quecksilber (0,0005 %), Cd: Cadmium (0,002 %),
Pb: Blei (0,004 %)
In der Europäischen Union gibt es unterschiedliche
Sammelsysteme für gebrauchte Elektrik- und Elektronikgeräte
einerseits sowie Batterien und Akkus andererseits.
Bitte entsorgen Sie dieses Gerät, Batterien und Akkus
vorschriftsmäßig bei Ihrer kommunalen Sammelstelle oder im
örtlichen Recycling-Zentrum.
Bitte helfen Sie uns, die Umwelt zu erhalten, in der wir leben!
Italiano
Questo prodotto MITSUBISHI ELECTRIC è stato progettato e
fabbricato con materiali e componenti di alta qualità, che possono
essere riciclati e/o riutilizzati.
Questo simbolo significa che i prodotti elettrici ed elettronici, le
batterie e gli accumulatori, devono essere smaltiti separatamente
dai rifiuti casalinghi alla fine della loro vita di servizio.
Se sotto il simbolo mostrato sopra è stampato un simbolo chimico, il
simbolo chimico significa che la batteria o l’accumulatore contiene
un metallo pesante con una certa concentrazione. Ciò viene
indicato come segue:
Hg: mercurio (0,0005%), Cd: cadmio (0,002%),
Pb: piombo (0,004%)
Nell’Unione Europea ci sono sistemi di raccolta differenziata per i
prodotti elettrici ed elettronici, le batterie e gli accumulatori usati.
Per disfarsi di questo prodotto, delle batterie e degli accumulatori,
portarli al centro locale di raccolta/riciclaggio dei rifiuti.
Aiutateci a conservare l’ambiente in cui viviamo!
Français
Votre produit Mitsubishi Electric est conçu et fabriqué avec des
matériels et des composants de qualité supérieure qui peuvent être
recyclés et/ou réutilisés.
Ce symbole signifie que les équipements électriques et électroniques,
les batteries et les accumulateurs, à la fin de leur durée de service,
doivent être éliminés séparément des ordures ménagères.
Si un symbole chimique est imprimé sous le symbole illustré
ci-dessus, il signifie que la batterie ou l'accumulateur contient une
certaine concentration de métal lourd. Elle sera indiquée comme
suit : Hg : mercure (0,0005%), Cd : cadmium (0,002%),
Pb : plomb (0,004%)
Dans l’Union Européenne, il existe des systèmes sélectifs de
collecte pour les produits électriques et électroniques, les batteries
et les accumulateurs usagés.
Nous vous prions donc de confier cet équipement, ces batteries et
ces accumulateurs à votre centre local de collecte/recyclage.
Aidez-nous à conserver l’environnement dans lequel nous vivons !
Les machines ou appareils électriques et électroniques contiennent
souvent des matières qui, si elles sont traitées ou éliminées de
manière
inappropriée,
peuvent
s’avérer
potentiellement
dangereuses pour la santé humaine et pour l’environnement.
Cependant, ces matières sont nécessaires au bon fonctionnement
de votre appareil ou de votre machine.
Pour cette raison, il vous est demandé de ne pas vous débarrasser
de votre appareil ou machine usagé avec vos ordures ménagères.
Español
Su producto MITSUBISHI ELECTRIC está diseñado y fabricado
con materiales y componentes de alta calidad que pueden ser
reciclados y/o reutilizados.
Este símbolo significa que el aparato eléctrico y electrónico, las
pilas, baterías y los acumuladores, al final de su ciclo de vida, se
deben tirar separadamente del resto de sus residuos domésticos.
Si hay un símbolo químico impreso debajo del símbolo mostrado
arriba, este símbolo químico significa que la pila, batería o el
acumulador contienen un metal pesado con cierta concentración.
Esto se indicará de la forma siguiente:
Hg: mercurio (0,0005%), Cd: cadmio (0,002%),
Pb: plomo (0,004%)
En la Unión Europea existen sistemas de recogida específicos para
productos eléctricos y electrónicos, pilas, baterías y acumuladores
usados.
Por favor, deposite los aparatos mencionados, las pilas, baterías y
acumuladores en el centro de recogida/reciclado de residuos de su
lugar de residencia local cuando quiera tirarlos.
i Ayúdenos a conservar el medio ambiente!
Português
O seu produto MITSUBISHI ELECTRIC foi concebido e produzido
com materiais e componentes de alta qualidade que podem ser
reciclados e/ou reutilizados.
Este símbolo significa que o equipamento eléctrico e electrónico, as
baterias e os acumuladores, no final da sua vida útil, devem ser
deitados fora separadamente do lixo doméstico.
Se houver um símbolo químico impresso por baixo do símbolo
mostrado acima, o símbolo químico indica que a bateria ou
acumulador contém metais pesados numa determinada
concentração. Isto aparecerá indicado da maneira seguinte:
Hg: mercúrio (0,0005%), Cd: cádmio (0,002%),
Pb: chumbo (0,004%)
Na União Europeia existem sistemas de recolha separados para
produtos eléctricos e electrónicos, baterias e acumuladores usados.
Por favor, entregue este equipamento, as baterias e os
acumuladores correctamente, no seu ponto local de
recolha/reciclagem.
Por favor, ajude-nos a conservar o ambiente em que vivemos!
Svenska
Denna produkt från MITSUBISHI ELECTRIC är designad och
tillverkad av material och komponenter med hög kvalitet som kan
återvinnas och/eller återanvändas.
Denna symbol betyder att förbrukade elektriska och elektroniska
produkter, batterier och ackumulatorer skall sorteras och hanteras
separat från hushållsavfall.
Om det finns en kemisk beteckning tryckt under ovanstående
symbol betyder det att batteriet eller ackumulatorn innehåller en
tungmetall med en viss koncentration. Detta anges på följande sätt:
Hg: kvicksilver (0,0005%), Cd: kadmium (0,002%),
Pb: bly (0,004%)
Inom den Europeiska Unionen finns det separata insamlingssystem
för begagnade elektriska och elektroniska produkter, batterier och
ackumulatorer.
Var vänlig lämna denna produkt, batterier och ackumulatorer hos
din lokala mottagningsstation för avfall och återvinning.
Var snäll och hjälp oss att bevara miljön vi lever i!
Dansk
Dit produkt fra MITSUBISHI ELECTRIC er designet og fremstillet
med kvalitetsmaterialer og komponenter, der kan genindvindes
og/eller genbruges.
Dette symbol viser, at elektrisk eller elektronisk udstyr, batterier og
akkumulatorer ikke må bortskaffes sammen med almindeligt
husholdningsaffald efter endt levetid.
Hvis der er trykt et kemisk symbol under symbolet ovenfor, betyder
det, at batteriet eller akkumulatoren indeholder en bestemt
koncentration af et tungmetal. Dette angives som følger:
Hg: kviksølv (0,0005 %), Cd: cadmium (0,002 %),
Pb: bly (0,004 %)
I EU er der særlige indsamlingsordninger for brugte elektriske og
elektroniske produkter, batterier og akkumulatorer.
Bortskaf udstyret, batterier og akkumulatorer korrekt på en lokal
affalds-/genbrugsplads.
Hjælp os med at bevare det miljø, vi lever i!
Norsk
For norske brukere:
Dette produktet fra MITSUBISHI ELECTRIC er konstruert og
produsert med materialer og komponenter av høy kvalitet, som kan
resirkuleres og/eller brukes om igjen.
Dette symbolet betyr at elektrisk og elektronisk utstyr, batterier og
akkumulatorer,
ikke
bør
kasseres
sammen
med
husholdningsavfallet når de har nådd slutten av sin levetid.
Hvis det er trykt et kjemisk symbol under det symbolet som er vist
over, betyr det kjemiske symbolet at batteriet eller akkumulatoren
inneholder et tungmetall i en viss konsentrasjon. Dette vil vises som
følger:
Hg: kvikksølv (0,0005 %), Cd: kadmium (0,002 %),
Pb: bly (0,004 %)
I Norge finnes det egne innsamlingssystemer for brukte elektriske
og elektroniske produkter, batterier og akkumulatorer.
Kasser dette utstyret, batteriene og akkumulatorene ved den
lokale gjenbruks- eller resirkuleringsstasjonen.
Hjelp oss å bevare det miljøet vi lever i!
Suomi
Tämä MITSUBISHI ELECTRIC -tuote on suunniteltu ja valmistettu
korkealuokkaisista materiaaleista ja/tai osista, jotka voidaan
kierrättää ja käyttää uudelleen.
Tämä symboli tarkoittaa, että sähkö- ja elektroniikkalaitteet, paristot
ja akut täytyy niiden käyttöiän jälkeen hävittää erillään
talousjätteistä.
Jos yllä olevan symbolin alapuolelle on painettu kemiallinen symboli,
se tarkoittaa, että paristolla tai akulla on tietty raskasmetallipitoisuus.
Se ilmoitetaan seuraavasti:
Hg: elohopea (0,0005 %), Cd: kadmium (0,002 %),
Pb: lyijy (0,004 %)
Käytetyillä sähkö- ja elektroniikkalaitteilla, paristoilla ja akuilla on
Euroopan Yhteisössä omat keräysjärjestelmänsä.
Toimita
tämä
laite,
paristot
ja
akut
paikalliseen
jätehuolto-/kierrätyskeskukseen.
Auta meitä suojelemaan ympäristöä, jossa elämme!
Nederlands
Mitsubishi Electric producten zijn ontwikkeld en gefabriceerd uit
eerste kwaliteit materialen. De onderdelen kunnen worden
gerecycled en/of worden hergebruikt.
Het symbool betekent dat de elektrische en elektronische
onderdelen, batterijen en accu’s op het einde van de gebruiksduur
gescheiden van het huishoudelijk afval moeten worden ingezameld.
Wanneer er onder het bovenstaande symbool een chemisch
symbool staat gedrukt, betekent dit dat de batterij of accu zware
metalen in een bepaalde concentratie bevat. Dit wordt als volgt
aangeduid:
Hg: kwik (0,0005%), Cd: cadmium (0,002%),
Pb: lood (0,004%)
In de Europese Unie worden elektrische en elektronische producten,
batterijen en accu’s afzonderlijk ingezameld.
Breng deze apparatuur, batterijen en accu’s dan naar het
gemeentelijke afvalinzamelingspunt.
Help ons mee het milieu te beschermen!
Ελληνικά
Το προϊόν MITSUBISHI ELECTRIC που διαθέτετε είναι σχεδιασμένο
και κατασκευασμένο από υλικά και εξαρτήματα υψηλής ποιότητας,
τα οποία μπορούν να ανακυκλωθούν ή/και να χρησιμοποιηθούν
ξανά.
Το σύμβολο αυτό σημαίνει ότι ο ηλεκτρικός και ηλεκτρονικός
εξοπλισμός, οι μπαταρίες και οι συσσωρευτές, στο τέλος της
διάρκειας ζωής τους, θα πρέπει να απορριφτούν ξεχωριστά από τα
υπόλοιπα οικιακά απορρίμματά σας.
Αν έχει εκτυπωθεί ένα χημικό σύμβολο κάτω από το σύμβολο που
απεικονίζεται ανωτέρω, αυτό το χημικό σύμβολο σημαίνει ότι η
μπαταρία ή ο συσσωρευτής περιέχει ένα βαρύ μέταλλο σε ορισμένη
συγκέντρωση. Αυτό θα υποδεικνύεται ως ακολούθως:
Hg: υδράργυρος (0,0005%), Cd: κάδμιο (0,002%),
Pb: μόλυβδος (0,004%)
Στην Ευρωπαϊκή Ένωση υπάρχουν ξεχωριστά συστήματα
συλλογής για τα χρησιμοποιημένα ηλεκτρικά και ηλεκτρονικά
προϊόντα, τις μπαταρίες και τους συσσωρευτές.
Παρακαλούμε διαθέστε αυτόν τον εξοπλισμό, τις μπαταρίες και τους
συσσωρευτές
στο
τοπικό
σας
κοινοτικό
κέντρο
συλλογής/ανακύκλωσης απορριμμάτων.
Βοηθήστε μας να προστατεύσουμε το περιβάλλον στο οποίο ζούμε!
0904874HK5201