Electrolux ergospace Operating instructions

Dust Magnet
+ Hepa H12 filtration
2193584-02Outline.indd 1
10/17/08 1:58:18 PM
2193584-02Outline.indd 2
10/17/08 1:58:18 PM
Electrolux Ergospace 진공 청소기를 구입해 주셔서 감사합니
다. 본 사용 설명서는 Ergospace 전 모델에 적용될 수 있습니
다. 따라서, 구입하신 모델에는 일부 부속품 또는 기능이 빠져
있을 수 있습니다. 세부 모델명 및 부속품명은 박스 겉면 라벨
에 표시되어 있습니다. 제품을 최상의 상태로 사용하려면 항상
Electrolux의 정품 부속품을 사용하십시오. 해당 정품 부속품은
사용하시는 진공 청소기에 가장 잘 맞게 특별 제작된 것입니다.
感謝您選用 Electrolux Ergospace 吸塵機。這些「操作說明」
覆蓋所有 Ergospace 型號。這表示您所選用的特定型號的某些
件。為了確保最佳的使用效果,請一律使用原廠的 Electrolux
Thank you for having chosen an Electrolux Ergospace vacuum
cleaner. These operating instructions cover all Ergospace models. This means that with your specific model, some accessories/features may not be included. Please refer to your specific
model and its accessories, which are shown on the outer box
label. In order to ensure the best result, always use original
Electrolux accessories. They have been designed especially for
your vacuum cleaner.
2193584-02Outline.indd 3
10/17/08 1:58:18 PM
2193584-02Outline.indd 4
10/17/08 1:58:19 PM
Telescopic tube
Extension tube.
Hose handle + hose
Carpet / hard floor nozzle
Dust magnet,
combination carpet / hard
floor nozzle
3 in 1 Multi tool nozzle.
Dust bag, s-bag® , dust
bag holder.
Turbo nozzle
Parquet nozzle
Easy Clean kit
Safety precautions
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified person
in order to avoid a hazard. Never use the vacuum cleaner if
the cable is damaged. Damage to the machine’s cable is not
covered by the warranty.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure that they do not play
with the appliance.
Please remove the plug from the socket outlet before cleaning
or maintaining the appliance.
Never use the vacuum cleaner:
In wet areas.
Close to flammable gases etc.
When housing shows visible signs of damage.
On sharp objects.
On hot or cold cinders, lighted cigarette butts, etc.
On fine dust, for instance from plaster, concrete, flour, hot or
cold ashes.
Using the vacuum cleaner in the above circumstances may
cause serious damage to its motor. Such damage is not covered
by the warranty. Never use the vacuum cleaner without its filters.
Electrical cable precautions
• A damaged cable should only be replaced by an authorised
Electrolux service centre.
• Damage to the machine’s cable is not covered by the
• Never pull or lift the vacuum cleaner by the cable.
• Disconnect the plug from the mains before cleaning or
maintenance of the vacuum cleaner.
• Regularly check that the cable is not damaged. Never use
the vacuum cleaner if the cable is damaged. All servicing
and repairs must be carried out by an authorised Electrolux
service centre. Be sure to keep the vacuum cleaner in a dry
place.If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similary qualified person
in order to avoid a hazard.
* Certain models only.
2193584-02Outline.indd 5
10/17/08 1:58:20 PM
2193584-02Outline.indd 6
10/17/08 1:58:21 PM
Before starting
Open the front cover on the machine and check that the
dust bag, s-bag® and the motorfilter are in place. (See also
Replacement of filter(s))
10 Open the back lid on the machine and check that the
exhaust filter is in place.
11 Insert the hose until the catches click to engage (press the
catches to release the hose). (2). Insert the hose into the
hose handle until the catches click to engage (press the
catches to release the hose).
12 Attach the extension tube* or telescopic tube* to the hose
handle and nozzle by pushing and twisting together. (Twist
and pull apart to dismantle.)
13 Extend the electric cable and connect it to the mains. The
vacuum cleaner is fitted with a cable winder. Once the
electric cable has been extended, it stays in that position.
14 To rewind the cable, press the cord rewinder button. The
cable will then rewind.
15 ON/OFF control: Push the ON-OFF button once to start the
vacuum cleaner. Push same button once more to turn it off.
16 Power Regulation: Twist the power control towards „max”
to increase the suction power. Twist the power control
towards „min” to decrease suction power. Additional suction
power control: Use the suction control on the hose handle.
17 Practical parking positions (and at the same time a
backsaving feature) when you pause during cleaning or
when you carry and store the vacuum cleaner.
18 You can also carry the vacuum cleaner using the handle
on top or on the lower front edge of the machine.
19 Keep the hose in place while storing the vacuum cleaner
by extending the elastic bumper cord and placing it across
the hose.
* Certain models only.
2193584-02Outline.indd 7
10/17/08 1:58:21 PM
2193584-02Outline.indd 8
10/17/08 1:58:22 PM
Getting the best results.
20 Accessories on board 3 in 1 multi tool nozzle to be found
in the back of the cleaner.
Use the nozzles as follows:
Carpets: * Use the carpet/hard floor nozzle with lever in position
(21). Reduce suction power for small carpets.
* On the Dust Magnet nozzle (23 and 24) there is normally
no need to switch mode. It can be used with brush up on all
surfaces for maximal convenience with maintained excellent
dust removal result. The brush setting should be used to reach
optimal dust removal even on difficult hard floors or to get a
combing effect on carpets.
Hard floors: * Use the carpet/hard floor nozzle with lever in
position (22).
Wooden floors: * Use the parquet nozzle (8).
Upholstery: Curtains, lightweight fabrics etc.: Use the upholstery
function of the 3 in 1 multi tool nozzle (5a). Reduce suction
power if necessary.
Frames, bookshelves, etc.: Use the dusting brush function of the 3
in 1 multi tool nozzle (5b).
* Use the easy clean kit (9).
Crevices, corners, etc.: Use the crevice function of 3 in 1 multi
tool nozzle (5c).
* Using the turbo nozzle (7)
Note: Do not use the turbo nozzle on skin rugs, rugs with long
fringes or a pile depth exceeding 15 mm. To avoid damaging
the carpet, do not keep the nozzle stationary whilst the brush is
rotating. Do not pass the nozzle across electric cables, and be
sure to switch off the vacuum cleaner immediately after use.
25 The dust bag must be replaced latest when the indicator
window is completely red. Read with the nozzle lifted up.
* Certain models only.
2193584-02Outline.indd 9
10/17/08 1:58:23 PM
2193584-02Outline.indd 10
10/17/08 1:58:24 PM
Replacing the dust bag, s-bag®
26 Open the front cover and lift out the insert holding the
27 Pull the cardboard to remove the s-bag® from the insert.
This automatically seals the s-bag® and prevents dust
leaking out.
28 Insert a new s-bag® by pushing the cardboard right into the
end of the groove in the insert.
29 Put the insert back into the bag compartment, and close
the cover.
Note. Replace the s-bag® even if it is not full (it could be
obstructed). Also replace after vacuuming carpet-cleaning
powder. Be sure to use only an original Electrolux dust bags,
s-bag® Classic, s-bag® Clinic Anti-Allergy, s-bag® Classic long
performance or s-bag® Anti-odour.
Replacement of the filter(s)
The more often the better for the efficiency of the cleaner.
In standard household use, the filters should be replaced
approximately every 3 years. Never use the vacuum cleaner
without filter(s).
Open the front cover and lift out the insert holding of s-bag®
30 Pull the filter(s) holder upwards until coming away from the
groove. Carefully pull the old, dirty filter(s) out of the filter
holder and replace with a new filter(s).
31 Reattach the filter holder containing the new filter(s). Put
the insert holding of s-bag® back in the cleaner and then
close the cover.
Replacement of the exhaust filter
The filters must always be replaced with new ones and cannot
be washed (if not mentioned).
32 Place your thumbs on the back edge of the lid and then
open the lid by pulling the handle backwards and upwards
with your index/middle finger.
33 Lift out the filter. Insert a new filter and replace the lid as
34 In case of models with washable HEPA filter. Rinse the
inside (dirty side) of the filter unit under warm tap water
only. Do not use cleaning agents and avoid touching the
delicate filter surface. Tap the filter frame to remove excess
water. Repeat cleaning procedure four times and allow the
filter to air dry. The original filtering performance is now
restored. Replace the unit back into the cleaner and close
cover ensuring it is properly fastened.
2193584-02Outline.indd 11
10/17/08 1:58:24 PM
2193584-02Outline.indd 12
10/17/08 1:58:25 PM
Cleaning the hose and nozzle
The vacuum cleaner stops automatically if the nozzle, tube,
hose or filters and s-bag® becomes blocked. In such cases,
disconnect from mains and allow to cool for 20-30 minutes.
Clear blockage and/or replace filters and s-bag® and restart.
Tubes and hoses
35 Use a cleaning strip or similar to clear the tubes and hose.
(2) Hose handle could be dismantled from hose if cleaning
is needed.
36 It may also be possible to remove the obstruction in the
hose by squeezing it. However, be careful in case the
obstruction is caused by glass or needles caught inside
the hose.
Note: The warranty does not cover any damage to the hose
caused by cleaning it.
Cleaning the floor nozzle
37 To avoid deterioration of suction power, frequently clean
the carpet/ hard floor nozzle. The easiest way to clean it is
by using the hose handle.
Cleaning the turbo nozzle*
38 Disconnect the nozzle from the vacuum cleaner tube and
remove entangled threads, etc. by snipping them away
with scissors. Use the hose handle to clean the nozzle.
* Certain models only.
2193584-02Outline.indd 13
10/17/08 1:58:25 PM
2193584-02Outline.indd 14
10/17/08 1:58:26 PM
The vacuum cleaner does not start
• Check that the cable is connected to the mains.
• Check that the plug and cable are not damaged.
• Check for a blown fuse.
The vacuum cleaner stops
• Check whether the dust bag, s-bag® is full. If so, replace it
with a new one.
• Is the nozzle, tube or hose blocked?
• Are the filters blocked?
Water has entered the vacuum cleaner
It will be necessary to replace the motor at an authorised
Electrolux service centre. Damage to the motor caused by the
penetration of water is not covered by the warranty.
Consumer information
Electrolux decline all responsibility for all damages arising from
any improper use of the appliance or in cases of tampering with
the appliance.
This product is designed with the environment in mind. All
plastic parts are marked for recycling purposes. For details see
our web site: www.electrolux.com
The symbol
on the product or on its packaging indicates
that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment
and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more detailed
information about recycling of this product, please contact your
local city office, your household waste disposal service or the
shop where you purchased the product.
2193584-02Outline.indd 15
10/17/08 1:58:26 PM
Share more thinking at www.electrolux.com
2193584-02Outline.indd 16
10/17/08 1:58:44 PM