Acer AcerPower 6500 User`s guide

Acer Projector
H6500/E-140/HE-802 Series
User's Guide
Copyright © 2011. Acer Incorporated.
All Rights Reserved.
Acer Projector H6500/E-140/HE-802 Series User's Guide
Original Issue: 09/2011
Changes may be made periodically to the information in this publication without obligation
to notify any person of such revisions or changes. Such changes will be incorporated in new
editions of this manual or supplementary documents and publications. This company makes
no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims the implied warranties of merchantability or fitness for a
particular purpose.
Record the model number, serial number, purchase date and place of purchase information in
the space provided below. The serial number and model number are recorded on the label
affixed to your projector. All correspondence concerning your unit should include the serial
number, model number and purchase information.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronically, mechanically, by photocopy, recording or otherwise,
without the prior written permission of Acer Incorporated.
Acer Projector H6500/E-140/HE-802 Series
Model number: __________________________________
Serial number: ___________________________________
Date of purchase: ________________________________
Place of purchase: ________________________________
Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies'
product names or trademarks are used herein for identification purposes only and belong to
their respective companies.
"HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC."
iii
Information for your safety and
comfort
Read these instructions carefully. Keep this document for future reference.
Follow all warnings and instructions marked on the product.
Turning the product off before cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Caution for plug as disconnecting device
Observe the following guidelines when connecting and disconnecting power to
the external power supply unit:
•
•
•
Install the power supply unit before connecting the power cord to the AC
power outlet.
Unplug the power cord before removing the power supply unit from the
projector.
If the system has multiple sources of power, disconnect power from the
system by unplugging all power cords from the power supplies.
Caution for Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible
and located as close to the equipment operator as possible. When you need to
disconnect power to the equipment, be sure to unplug the power cord from the
electrical outlet.
Warnings!
•
•
•
Do not use this product near water.
Do not place this product on an unstable cart, stand or table. If the product
falls, it could be seriously damaged.
Slots and openings are provided for ventilation to ensure reliable
operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should never be placed near or over a radiator or heat register, or
in a built-in installation unless proper ventilation is provided.
•
Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind onto or into
the product.
iv
•
•
To avoid damage of internal components and to prevent battery leakage,
do not place the product on a vibrating surface.
Never use it under sporting, exercising, or any vibrating environment
which will probably cause unexpected short current or damage rotor
devices, lamp.
Using electrical power
•
•
•
•
•
This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult
your dealer or local power company.
Do not allow anything to rest on the power cord. Do not locate this
product where people will walk on the cord.
If an extension cord is used with this product, make sure that the total
ampere rating of the equipment plugged into the extension cord does not
exceed the extension cord ampere rating. Also, make sure that the total
rating of all products plugged into the wall outlet does not exceed the fuse
rating.
Do not overload a power outlet, strip or receptacle by plugging in too
many devices. The overall system load must not exceed 80% of the branch
circuit rating. If power strips are used, the load should not exceed 80% of
the power strip's input rating.
This product's AC adapter is equipped with a three-wire grounded plug.
The plug only fits in a grounded power outlet. Make sure the power outlet
is properly grounded before inserting the AC adapter plug. Do not insert
the plug into a non-grounded power outlet. Contact your electrician for
details.
Warning! The grounding pin is a safety feature. Using a power outlet that is
not properly grounded may result in electric shock and/or injury.
Note: The grounding pin also provides good protection from unexpected
noise produced by other nearby electrical devices that may interfere with
the performance of this product.
•
Use the product only with the supplied power supply cord set. If you need
to replace the power cord set, make sure that the new power cord meets
the following requirements: detachable type, UL listed/CSA certified, VDE
approved or its equivalent, 4.5 meters (15 feet) maximum length.
v
Product servicing
Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks. Refer all servicing to
qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
•
•
•
•
•
•
the power cord or plug is damaged, cut or frayed
liquid was spilled into the product
the product was exposed to rain or water
the product has been dropped or the case has been damaged
the product exhibits a distinct change in performance, indicating a need
for service
the product does not operate normally after following the operating
instructions
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to normal condition.
Warning! For safety reasons, do not use non-compliant parts when adding
or changing components. Consult your reseller for purchase options.
Your device and its enhancements may contain small parts. Keep them out of
the reach of small children.
Additional safety information
•
•
•
Do not look into the projector's lens when the lamp is on. The bright may
hurt your eyes.
Turn on the projector first and then signal sources
Do not place the product in following environments:
•
•
•
•
•
•
•
Space that is poorly ventilated or confined. At least 50cm clearance from walls
and free flow of air around the projector is necessary.
Locations where temperatures may become excessively high, such as inside of a
car with all windows rolled up.
Locations where excessive humidity, dust, or cigarette smoke may contaminate
optical components, shortening the life span and darkening the image.
Locations near fire alarms.
Locations with an ambient temperature above 40 ºC/104 ºF.
Locations where the altitudes are higher than 10000 feet.
Unplug immediately if there is something wrong with your projector. Do
not operate if smoke, strange noise or odor comes out of your projector. It
vi
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
might cause fire or electric shock. In this case, unplug immediately and
contact your dealer.
Do not keep using this product to break or drop it. In this case contact your
dealer for inspection.
Do not face the projector lens to the sun. It can lead to fire.
When switching the projector off, suggest to ensure the projector
completes its cooling cycle before disconnecting power.
Do not frequently turn off the main power abruptly or unplug the
projector during operation. The best way is to wait for the fan to turn off
before turning main power off.
Do not touch air outlet grille and bottom plate which becomes hot.
Clean the air filter frequently if have. The temperature inside may rise and
cause damage when the filter/ventilation slots clogged with dirt or dust.
Do not look into the air outlet grille when projector is operating. It may
hurt your eyes.
Always open the lens shutter or remove the lens cap when the projector is
on.
Do not block the projector lens with any object when the projector is
under operation as this could cause the object to become heated and
deformed or even cause a fire. To temporarily turn off the lamp, press HIDE
on the remote control.
The lamp becomes extremely hot during operation. Allow the projector to
cool for approximately 45 minutes prior to removing the lamp assembly for
replacement.
Do not operate lamps beyond the rated lamp life. It could cause it to break
on rare occasions.
Never replace the lamp assembly or any electronic components unless the
projector is unplugged.
The product will detect the life of the lamp itself. Please be sure to change
the lamp when is showing warning message.
When changing the lamp, please allow unit to cool down, and follow all
changing instructions.
Reset the "Lamp Hour Reset" function from the Onscreen display
"Management" menu after replacing the lamp module.
Do not attempt to disassemble this projector. There are dangerous high
voltages inside which may hurt you. The only user serviceable part is the
lamp which has its own removable cover. Refer servicing only to suitable
qualified professional service personnel.
Do not stand the projector on end vertically. It may cause the projector to
fall over, causing injury or damage.
This product is capable of displaying inverted images for ceiling mount
installation. Only use acer ceiling mount kit for mounting the projector
and ensure it is securely installed.
vii
Caution for Listening
To protect your hearing, follow these instructions.
•
•
•
•
•
Increase the volume gradually until you can hear clearly and comfortably.
Do not increase the volume level after your ears have adjusted.
Do not listen to music at high volumes for extended periods.
Do not increase the volume to block out noisy surroundings.
Decrease the volume if you can't hear people speaking near you.
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize
pollution and ensure utmost protection of the global environment, please
recycle. For more information on the Waste from Electrical and Electronics
Equipment (WEEE) regulations, visit http://www.acer-group.com/public/
Sustainability/sustainability01.htm
Mercury advisory
For projectors or electronic products containing an LCD/CRT monitor or display:
“Lamp(s) contain Mercury,
Dispose Properly.”
Lamp(s) inside this product contain mercury and must be recycled or disposed of
according to local, state or federal laws. For more information, contact the
Electronic Industries Alliance at www.eiae.org. For lamp-specific disposal
information, check www.lamprecycle.org
viii
First things first
Usage Notes
Do:
•
Turn off the product before cleaning.
•
Use a soft cloth moistened with mild detergent to clean the display
housing.
•
Disconnect the power plug from AC outlet if the product is not being used
for a long period of time.
Don't:
•
Block the slots and openings on the unit provided for ventilation.
•
Use abrasive cleaners, waxes or solvents to clean the unit.
•
Use under the following conditions:
•
•
•
•
In extremely hot, cold or humid environments.
In areas susceptible to excessive dust and dirt.
Near any appliance that generates a strong magnetic field.
Place In direct sunlight.
Precautions
Follow all warnings, precautions and maintenance as recommended in this
user's guide to maximize the life of your unit.
Warning:
•
•
Do not look into the projector's lens when the lamp is on. The bright light may hurt
your eyes.
To reduce the risk of fire or electric shock, do not expose this product to rain or
moisture.
•
•
Please do not open or disassemble the product as this may cause electric shock.
•
This product will detect the life of the lamp itself. Please be sure to change the lamp
when it shows warning messages.
•
Reset the "Lamp Hour Reset" function from the Onscreen display "Management"
menu after replacing the lamp module.
•
When switching the projector off, please ensure the projector completes its cooling
cycle before disconnecting power.
•
•
•
Turn on the projector first and then the signal sources.
When changing the lamp, please allow unit to cool down, and follow all changing
instructions.
Do not use lens cap when projector is in operation.
When the lamp reaches the end of its life, it will burn out and may make a loud
popping sound. If this happens, the projector will not turn back on until the lamp
module has been replaced. To replace the lamp, follow the procedures listed under
"Replacing the Lamp".
First things first
iii
viii
Usage Notes
viii
Precautions
viii
Introduction
1
Product Features
1
Package Overview
2
Projector Overview
3
Projector Outlook
3
Control Panel
4
Remote Control Layout
5
Getting Started
7
Connecting the Projector
7
Turning the Projector On/Off
8
Turning on the Projector
8
Turning the projector off
9
Adjusting the Projected Image
10
Adjusting the Height of Projected Image
10
How to optimize image size and distance
11
How to get a preferred image size by adjusting
distance and zoom
13
User Controls
15
Installation menu
15
Acer Empowering Technology
16
Onscreen Display (OSD) Menus
17
Color
18
Image
20
Management
21
Setting
23
Timer
25
Language
25
Appendices
Troubleshooting
26
26
Contents
Information for your safety and comfort
LED & Alarm Definition Listing
30
Replacing and cleaning the dust filters
31
Replacing the Lamp
32
Ceiling Mount Installation
33
Specifications
36
Compatibility modes
38
Regulations and safety notices
42
1
Product Features
This product is a single-chip DLP® projector. Outstanding
features include:
•
DLP® technology
•
Native 1920 x 1080 1080p resolution
4:3 / 16:9 / L.Box aspect ratio supported
•
Acer ColorBoost technology delivers nature’s true colors for vivid, life-like
images
•
Acer ColorSafe II technology ensures consistent color rendition over time.
•
High brightness and contrast ratio
•
Versatile display modes (Bright, Presentation, Standard, Movie, Dark
Cinema, Game, Sports, User) enable optimum performance in any situation
•
NTSC / PAL / SECAM compatible and HDTV (720p, 1080i, 1080p) supported
•
Lower power consumption and economy (ECO) mode extends lamp life
•
Acer EcoProjeciton Technology delivers Intelligent power management
approach and physical efficiency improvement
•
Empowering Key reveals Acer Empowering Technology utilities (Acer
eView, eTimer, ePower Management) for easy adjustment of settings
•
Equipped with HDMITM connection supporting HDCP
•
Advanced digital keystone correction optimizes presentations
•
Smart detection delivers quick, intelligent source detection.
•
Multi-language onscreen display (OSD) menus
•
Full-function remote control
•
Manual focus projection lens zooms up to 1.2x
•
8x digital zoom and pan move function
•
Microsoft® Windows® 2000, XP, Vista®, Windows® 7, OS compliant
English
Introduction
English
2
Package Overview
This projector comes with all the items shown below. Check to
make sure your unit is complete. Contact your dealer
immediately if any thing is missing.
Projector with lens cap
Power cord
VGA cable
POWER
ASPECT
RATIO
Security Card
FREEZE
HIDE
RESYNC
SOURCE
ZOOM
Acer Projector
H6500/E-140/HE-802
Series
P/N:MU.JD500.001
RGB
BRIGHTNESS
COLOR
CONTRAST
VGA
COMPONENT
VIDEO
S-VIDEO
DVI
HDMI
WIRELESS
MUTE
PgUp
PgDn
Security card
User's guide
Remote control
Quick start guide
2 x Batteries
Carrying case
Dust filters (Option)
3
English
Projector Overview
Projector Outlook
Front / upper side
1
7
6
8
9
7
2
3
5
#
4
10
Description
#
6
Description
1
Control panel
Zoom lever
2
Ventilation (inlet)
7
Remote control receivers
3
Ventilation (outlet)
8
Focus ring
4
Elevator button
9
Zoom lens
5
Elevator foot
10 Lens cap
Rear side
3
2
4
5
1
#
1
6
7
8
9
Description
#
Description
Power socket
6
HDMI 1 connector
2
USB connector
7
HDMI 2 connector
3
PC analog signal/HDTV/component
video input connector (VGA IN)
8
12V DC output connector
4
YPbPr/YCbCr input connector
9
Kensington™ lock port
5
Composite video input connector
English
4
Control Panel
1
6
2
7
3
8
10
4
5
9
2
#
Icon
Function
Description
1
LAMP
Lamp Indicator LED
2
Keystone
Adjusts the image to compensate for
distortion caused by tilting the projector (±
15 degrees).
3
RESYNC
Automatically synchronizes the projector
to the input source.
4
MENU
•
Press "MENU" to launch the Onscreen
display (OSD) menu, back to the
previous step for the OSD menu
operation or exit the OSD menu.
•
Confirm your selection of items.
5
POWER
See the contents in "Turning the Projector
On/Off" section.
6
TEMP
Temp Indicator LED
7
Four directional select
Use
to select items or make
keys
adjustments to your selection.
8
SOURCE
Changes the active source.
9
Empowering key
Unique Acer functions: eView, eTimer,
ePower Management.
10
Remote control
receiver
Receives signals from remote control.
5
1
POWER
2
3
4
5
6
FREEZE
HIDE
RESYNC
SOURCE
7
ASPECT
RATIO
8
9
ZOOM
26
10
11
RGB
13
14
17
18
21
22
BRIGHTNESS
COLOR
CONTRAST
PgUp
PgDn
VGA
COMPONENT
VIDEO
S-VIDEO
DVI
HDMI
WIRELESS
MUTE
12
15
16
19
20
23
24
25
#
1
Icon
Function
Description
2
3
Infrared
transmitter
FREEZE
HIDE
Sends signals to the projector.
4
5
6
RESYNC
SOURCE
POWER
7
8
9
ASPECT RATIO
To choose the desired aspect ratio (Auto/4:3/16:9/L.Box)
ZOOM
Zooms the projector display in or out.
Empowering key Unique Acer functions: eView, eTimer, ePower Management.
10
KEYSTONE
11
MENU
12
PAGE
13
14
15
RGB
BRIGHTNESS
CONTRAST
To pause the screen image.
Momentarily turns off the video. Press "HIDE" to hide the
image, press again to display the image.
Automatically synchronizes the projector to the input source.
Changes the active source.
Refer to the "Turning the Projector On/Off" section.
Adjusts the image to compensate for distortion caused by
tilting the projector (± 15 degrees).
• Press "MENU" to launch the Onscreen display (OSD) menu,
back to the previous step for the OSD menu operation or
exit the OSD menu.
• Confirm your selection of items.
No function.
Press "RGB" for true-color optimization.
Press "BRIGHTNESS" to adjust the brightness of the image.
Use the "CONTRAST" option to control the difference
between the lightest and darkest parts of the picture.
English
Remote Control Layout
English
6
#
16
17
18
19
20
21
22
23
24
25
26
Icon
Function
Description
COLOR
VGA
Press "COLOR" to adjust the color temperature of image.
Press "VGA" to change source to the VGA connector. This
connector supports analog RGB, YPbPr (480p/576p/720p/
1080i), YCbCr (480i/576i) and RGBsync.
COMPONENT
Press "COMPONENT" to change source to Component video.
This connection supports YPbPr (480p/576p/720p/1080p) and
YCbCr (480i/576i/1080i).
S-VIDEO
No function.
VIDEO
To change source to COMPOSITE VIDEO.
DVI
No function.
HDMI™
To change source to HDMI™.
MUTE
No function.
WIRELESS
No function.
KeyPad 0~9
Press "0~9" to input a password in the "Security settings".
Four directional Use up, down, left, right buttons to select items or make
select keys
adjustments to your selection.
Note: When PIP function is activated, zoom and keystone function
is unavailable.
7
English
Getting Started
Connecting the Projector
R B G
DVD player,
Set-top Box,
HDTV receiver
USB
5
D-Sub
Video Output
R B G
3
Y
2
4
USB
6
D-Sub
8
HDTV adapter
Y
HDMI
G
B
R
7
1
5
HDMI
R B G
DVD player,
Set-top Box,
HDTV receiver
#
Description
#
Description
1
Power cord
5
3 RCA component cable
2
USB cable
6
Composite video cable
3
VGA cable
7
HDMI cable
4
VGA to component/HDTV adapter
8
12V DC Cable
Note: To ensure the projector works well with your computer,
please make sure the timing of the display mode is compatible
with the projector.
English
8
Turning the Projector On/Off
Turning on the Projector
1
Remove the lens cap.(Illustration #1)
2
Ensure that the power cord and signal cable are securely connected. The
Power indicator LED will flash red.
3
Turn on the projector by pressing "Power" button on the control panel,
and the Power indicator LED will turn blue.(Illustration #2)
4
Turn on your source (computer, notebook, video player ,etc.). The
projector will detect your source automatically.
•
If the screen displays "Lock" and "Source" icons, it means the projector is locked
onto a specific source type and there is no such type of input signal detected.
•
If the screen displays "No Signal", please make sure the signal cables are
securely connected.
•
If you connect to multiple sources at the same time, use the "Source" button on
either control panel or the remote control or direct source key on the remote
control to switch between inputs.
2
Power button
1
Lens cap
9
1
To turn the projector off, press the power button. This message appears:
"Please press the power button again to complete the shutdown process."
Press the power button again.
2
The LED power indicator will turn RED and blink rapidly after the projector
is turned off, and the fan(s) will continue to operate for about 2 minutes to
ensure that the system cools properly.
3
As long as the power cord remains plugged in, you can press the power
button to turn the projector immediately back on anytime during the 2minute shutdown process.
4
Once the system has finished cooling, the LED power indicator will stop
blinking and turn solid red to indicate standby mode.
5
It is now safe to unplug the power cord.
Warning indicators:
•
"Projector Overheated. Lamp will automatically turn off soon."
This onscreen message indicates that the projector has overheated.
The lamp with automatically turn off, the projector will automatically
shut down, and the LED temp indicator will turn solid red. Contact
your local dealer or service center.
•
"Fan failed. Lamp will automatically turn off soon."
This onscreen message indicates that the fan has failed. The lamp will
automatically turn off, the projector will automatically shut down,
and the LED temp indicator will blink. Contact your local dealer or
service center.
Note: Whenever the projector automatically shuts down and the
LED lamp indicator turns solid red, contact your local reseller or
service center.
English
Turning the projector off
English
10
Adjusting the Projected Image
Adjusting the Height of Projected Image
The projector is equipped with elevator feet for adjusting the height of image.
To raise the image:
1
Press the elevator foot release. (Illustration #1)
2
Raise the image to the desired height angle (Illustration #2), then release
the button to lock the elevator foot into position.
3
Use Tilt adjusting wheel (Illustration #3) to fine-tune the display angle.
To lower the image:
1
Press the elevator foot release. (Illustration #1)
2
Lower the image to the desired height angle (Illustration #2) , then release
the button to lock the elevator foot into position.
3
Use Tilt adjusting wheel (Illustration #3) to fine-tune the display angle.
1
Elevator foot
release button
3
Tilt adjusting wheel
2
Elevator foot
11
Consult the table below to find the optimal image sizes achievable when the
projector is positioned at a desired distance from the screen. Example: If the
projector is 3 m from the screen, good image quality is possible for image sizes
between 75" and 90".
Note: Remind as below figure, the space of 131 cm height is
required when located at 3m distance.
Ma
x sc
re e
Min
n si
ze
sc re
en
si
ze
B
90"
75 "
Height: 131cm
Form base to
top of image
Height:
109cm
C
A
3m Desired Distance
Figure: Fixed distance with different zoom and screen size.
English
How to optimize image size and distance
English
12
Screen size
Top
Screen size
Top
Desired
(Min zoom)
(Max zoom)
Distance
From base
From base to
(m)
Diagonal
Diagonal
to top of
top of image
<A>
(inch) W (cm) x H (cm)
(inch) W (cm) x H (cm)
image (cm)
(cm)
<B>
<B>
<C>
<C>
1.5
38
83 x 47
54
45
100 x 56
65
2
50
111 x 63
73
60
133 x 75
87
2.5
63
139 x 78
91
75
167 x 94
109
3
75
167 x 94
109
90
200 x 113
131
3.5
88
194 x 109
127
105
233 x 131
152
4
100
222 x 125
145
120
267 x 150
174
4.5
113
250 x 141
163
136
300 x 169
196
5
125
278 x 156
181
151
333 x 188
218
6
151
333 x 188
218
181
400 x 225
261
7
176
389 x 219
254
211
467 x 263
305
8
201
444 x 250
290
241
533 x 300
348
9
226
500 x 281
326
271
600 x 338
392
10
251
556 x 313
363
301
667 x375
435
Zoom Ratio: 1.2x
13
A
60"
Desired
image size
D
Height: 87cm
Form base to
top of image
2m
2.4 m
C
B
Desired Distance
The table below shows how to achieve a desired image size by adjusting either
the position or the zoom ring. For example: to obtain an image size of 60" set
the projector at a distance 2.0 m and 2.4 m from the screen and adjust the zoom
level accordingly.
English
How to get a preferred image size by adjusting
distance and zoom
English
14
Desired Image Size
Distance (m)
Top (cm)
Diagonal (inch)
<A>
W (cm) x H (cm)
Max zoom
<B>
Min zoom
<C>
From base to top of
image
<D>
30
66 x 37
1.0
1.2
43
40
89 x 50
1.3
1.6
58
50
111 x 62
1.7
2.0
72
60
133 x 75
2.0
2.4
87
70
155 x 87
2.3
2.8
101
80
177 x 100
2.7
3.2
116
90
199 x 112
3.0
3.6
130
100
221 x 125
3.3
4.0
144
120
266 x 149
4.0
4.8
173
150
332 x 187
5.0
6.0
217
180
398 x 224
6.0
7.2
260
200
443 x 249
6.6
8.0
289
250
553x 311
8.3
10.0
361
300
664 x 374
10.0
***
433
Zoom Ratio: 1.2x
15
Installation menu
The installation menu provides an onscreen display (OSD) for projector
installation and maintenance. Use the OSD only when the message "No signal
input" is displayed on the screen.
The menu options include settings and adjustments for screen size and distance,
focus, keystone correction and more.
1
Turn on the projector by pressing "Power" button on the control pad.
2
Press the "MENU" button on the control pad to launch the OSD for
projector installation and maintenance.
3
The background pattern acts as a guide to adjusting the calibration and
alignment settings, such as screen size and distance, focus and more.
4
The Installation menu includes the following options:
•Projection method
•Projection location
•Menu location
•Keystone settings
•Language settings
•Reset to factory default function
Use the up and down arrow keys to select an option, the left and right
arrow keys to adjust selected option settings, and the right arrow key to
enter a submenu for feature setting. The new settings will be saved
automatically upon exiting the menu.
5
Push the menu button anytime to exit the menu and return to the Acer
welcome screen.
English
User Controls
English
16
Acer Empowering Technology
Empowering
Key
Acer eView Management
Acer Empowering Key provide three
Acer unique functions, they are "Acer
eView Management", "Acer eTimer
Management" and "Acer ePower
Management" respectively. Press " "
key for more than one second to launch
the Onscreen display main menu to
modify its function.
Press " " to launch "Acer eView
Management" submenu.
"Acer eView Management" is for
display mode selection. Please refer to
Onscreen Display Menus section for
more detail.
Acer eTimer Management
Press " " to launch "Acer eTimer
Management" submenu.
"Acer eTimer Management" provides
the reminding function for presentation
time control. Please refer to Onscreen
Display Menus section for more detail.
Acer ePower Management
Press " " to launch "Acer ePower
Management".
"Acer ePower Management" provides
user one shortcut to save lamp and
projector life. Please refer to Onscreen
Display section for more detail.
17
The projector has multilingual OSD that allow you to make image adjustments
and change a variety of settings.
Using the OSD menus
•
To open the OSD menu, press "MENU" on the remote control or control
panel.
•
When the OSD is displayed, use the
keys to select any item in the
main menu. After selecting the desired main menu item, press
to enter
submenu for feature setting.
•
Use the
keys to select the desired item and adjust the settings by
using the
keys.
•
Select the next item to be adjusted in the submenu and adjust as described
above.
•
Press "MENU" on the remote control or control panel, the screen will
return to the main menu.
•
To exit OSD, press "MENU" on the remote control or control panel again.
The OSD menu will close and the projector will automatically save the new
settings.
Main menu
Setting
Sub menu
English
Onscreen Display (OSD) Menus
English
18
Color
Display Mode
There are many factory presets optimized for various types of
images.
•
•
Bright: For brightness optimization.
•
•
•
•
•
•
Standard: For common environment.
Presentation: For meeting presentation with higher
brightness.
Movie: For brighter and general movie/video/photo playing.
Dark Cinema: For dark movie content.
Game: For game content.
Sports: For sport picture.
User: Memorize user’s settings.
Wall Color
Use this function to choose a proper color according to the wall.
There are several choices, including white, light yellow, light blue,
pink, dark green. It will compensate the color deviation due to the
wall color to show the correct image tone.
Brightness
Adjust the brightness of the image.
Contrast
•
Press
to darken image.
•
Press
to lighten the image.
"Contrast" controls the difference between the lightest and
darkest parts of the picture. Adjusting the contrast changes the
amount of black and white in the image.
•
Press
to decrease the contrast.
•
Press
to increase the contrast.
Color
Temperature
Adjust the color temperature. At higher color temperatures, the
screen looks colder; at lower color temperatures, the screen looks
warmer.
Degamma
Effects the representation of dark scenery. With greater gamma
value, dark scenery will look brighter.
19
Noise Reduction
Adjusts signal noise reduction."0" means the noise reduction is off,
">0" increase noise reduction.
Sharpeness
Adjusts the sharpness of the image.
•
Press
to decrease the sharpness.
•
Press
to increase the sharpness.
Brilliant Color
Produces an expanded on-screen color spectrum that delivers
enhanced color saturation for bright, true-to-life images. This
feature is "On" by default.
Dynamic Black
Choose "On" to automatically optimize the display of dark movie
scenes enabling them to be shown in incredible detail.
Color
Management
Color R
Adjusts the red color.
Color G
Adjusts the green color.
Color B
Adjusts the blue color.
Color C
Adjusts the cyan color.
Color Y
Adjusts the yellow color.
Color M
Adjusts the magenta color.
Skin Color
Adjusts the skin color.
Saturation
Adjusts a video image from black and white to fully saturated
color.
Tint
•
Press
to decrease the amount of color in the image.
•
Press
to increase the amount of color in the image.
Adjusts the color balance of red and green.
HDMI Color
Range
•
Press
to increase the amount of green in the image.
•
Press
to increase the amount of red in the image.
Adjust the color range of the HDMI image data to correct color
display error.
•
•
Auto: Automatically adjust by information from player.
•
Full Range: Prosess the input image as full color range data.
Limited Range: Prosess the input image as limited color range
data.
Note: "Saturation" and "Tint" functions are not supported under computer
mode or HDMI mode.
Note: "HDMI Color Range" function is only supported under HDMI mode.
English
Advanced
English
20
Image
Projection
Front
•
The factory default setting.
Ceiling
•
When you select this function, the projector inverts the image for
ceiling-mounted projection.
Rear
•
When you select this function, the projector reverses the image so
you can project from behind a translucent screen.
Rear-Ceiling
•
When you select this function, the projector reverses and inverts
the image at same time. You can project from behind a
translucent screen with ceiling mounted projection.
Aspect Ratio
Use this function to choose your desired aspect ratio.
•
Auto: Keep the image with original width-higth ratio and maxi
mize the image to fit native horizontal or vertical pixels.
•
4:3: The image will be scaled to fit the screen and displayed using
a 4:3 ratio.
•
16:9: The image will be scaled to fit the width of the screen and
the height adjusted to display the image using a 16:9 ratio.
•
L. Box: Keep original signal aspect ratio and zoom in by 1.333
times.
Keystone
Adjust image distortion caused by tilting projection. (±15 degrees)
21
•
•
Press
to move the image left.
Press
to to move the image right.
V. Position
(Vertical position)
•
•
Press
to move the image down.
Press
to move the image up.
Frequency
"Frequency" changes the projector's refresh rate to match the
frequency of your computer’s graphics card. If you can see a vertical
flickering bar in the projected image, use this function to make the
necessary adjustments.
Tracking
Synchronizes the signal timing of the projector with the graphics card.
If you experience an unstable or flickering image, use this function to
correct it.
HDMI Scan Info
Adjust the overscan ratio of the HDMI image on screen.
•
•
•
Auto: Automatically adjust by information from player.
Underscan: Always no overscan on HDMI image.
Overscan: Always keep overscan on HDMI image.
Note: "H. Position", "V. Position", "Frequency" and "Tracking" functions
are not supported under HDMI or Video mode.
Note: "HDMI Scan Info" function is only supported under HDMI mode.
Management
ECO Mode
Choose "On" to dim the projector lamp which will lower power
consumption, extend the lamp life and reduce noise. Choose "Off"
to return normal mode.
High Altitude
Choose "On" to turn on High Altitude mode. Operate the fans at
full speed continuously to allow for proper high altitude cooling of
the projector.
Auto Shutdown
The projector will automatically shutdown when there is no signal
input after the allocated time. (in minutes)
Turn Off Mode
•
•
Standard: Properly shuts down the projector after fan cooling.
Instant Resume: Resumes the system when the Power button is
pressed again within 2 minutes.
English
H. Position
(Horizontal
position)
English
22
Lamp Hour Elapse
Displays the lamp’s elapsed operating time (in hours).
Lamp Reminding
Activate this function to display a reminder to change the lamp 30
hours before its expected end-of-life.
Lamp Hour Reset
Press the
button and choose "Yes" to turn the lamp hour
counter to 0 hours.
23
English
Setting
Menu Location
Choose the menu location on the display screen.
Closed Caption
Selects a preferred closed captioning mode from CC1, CC2, CC3,
CC4, (CC1 displays captions in the primary language in your area).
Select "Off" to turn off the captioning feature. This function is only
available when a composite video or S-Video input signal is
selected and its system format is NTSC.
<Note> Set your screen aspect ratio to 4:3. This function is not
available when the aspect ratio is "16:9" or "Auto" .
Security
Security
This projector provides a useful security function for the
administrator to manage usage of the projector .
Press
to change the "Security" setting. If the security function is
enabled, your must enter the "Administrator Password" first
before changing the security settings.
•
Select "On" to enable the security function. The user has to
enter a password to operate the projector. Please refer to the
"User Password" section for details.
•
If "Off" is selected, then the user can turn on the projector
without password.
Timeout(Min.)
Once "Security" is activated to "On", the administrator can set
timeout function.
•
Press
•
•
The range is from 10 minute to 990 minutes.
•
•
The factory default setting of "Timeout(Min.)" is "Off".
or
to select the timeout interval.
When the time is up, the projector will prompt the user to
enter the password again.
Once the security function is enabled, the projector will
request user to enter password when switch on the projector .
Both "User Password" and "Administrator Password" can be
accepted for this dialogue.
Note: For 1080P models, to get best quality for you desired image, suggest
end-user set PC resolution to 1920 x 1080 before you use this function.
24
English
User password
•
Press
•
Press number keys to set your password on the remote control
and press "MENU" to confirm.
•
Press
•
Enter the password when you see "Confirm Password"
displayed.
•
•
The password should be between 4 and 8 characters long.
•
If you select "Always request the password when turning the
projector on.", the user has to enter the password every time
when the projector is turned on.
to setup or change the "User Password".
to delete character.
If you select "Request password only when plugging the
power cord in.", the projector will prompt the user to enter
the password every time the power cord is plugged.
Administrator Password
The "Administrator Password" can be used in both the "Enter
Administrator Password" and "Enter Password" dialog boxes.
•
Press
•
The factory default of "Administrator Password" is "1234".
to change the "Administrator Password".
If you forgot your administrator password, do the following to
retrieve the administrator password:
•
An unique 6-digit "Universal Password" which is printed on
the Security Card (please check accessory in the box). This
unique password is the number which will be accepted by
projector anytime no matter what the Administrator
Password is.
•
If losing this security card and number, please contact with an
Acer service center.
Auto Screen
Default is "On", the down/up move of electronic screen will be
related with power on/off of Projector.
Reset
•
Press the
button and choose "Yes" to return the
parameters on all menus to the factory default settings.
PIP
PIP Source
•
•
Press
Choose "On" to see two screens at the same time.
Choose "Off" to disable the function.
and
to choose the secondary video source: Composite,
S-Video or Component signal.
PIP Location
Choose the PIP secondary signal location on the display screen.
PIP Size
Choose the PIP secondary signal size on the display screen.
Note: When PIP function is activated, zoom and keystone function
is unavailable.
Note: "PIP", " PIP Source", "PIP Location" and "PIP Size" functions
are only supported under HDMI mode.
25
English
Timer
Timer Location
•
Choose the location of the timer on the screen.
Timer Start
•
Press
to start or stop the timer.
Timer Period
•
Press
or
to adjust the timer period.
Timer Display
•
Press
or
to which timer mode to display on the
screen.
Language
Language
Choose the multilingual OSD menu. Use the
select your preferred menu language.
•
Press
to confirm the selection.
or
key to
English
26
Appendices
Troubleshooting
If you experience a problem with your Acer projector, refer to the following
troubleshooting guide. If the problem persists, please contact your local reseller
or service center.
Image Problems and Solutions
#
1
2
Problem
No image appears
onscreen
Partial, scrolling
or incorrectly
displayed
image(For PC
(Windows 2000/
XP/Vista/Windows
7))
Solution
•
Connected as described in the "Getting Started"
section.
•
Ensure none of the connector pins are bent or
broken.
•
Check if the projector lamp has been securely
installed. Please refer to the "Replacing the Lamp"
section.
•
Make sure you have removed the lens cap and the
projector is switched on.
•
Press "RESYNC" on the remote control or control
panel.
•
For an incorrectly displayed image:
•
Open "My Computer," open the "Control
Panel," and then double-click the "Display"
icon.
•
Select the "Settings" tab.
•
Verify that your display resolution setting is
lower than or equal to UXGA (1600 x 1200).
•
Click the "Advanced Properties" button.
If the problem still appears, change the monitor display
you are using and follow the steps below:
•
Verify that the resolution setting is lower than
or equal to UXGA (1600 x 1200).
•
Click the "Change" button under the
"Monitor" tab.
•
Click "Show all devices". Next, select "Standard
monitor types" under the SP box, and choose
the resolution mode you need under the
"Models" box.
•
Verify that the resolution setting of the
monitor display is lower than or equal to UXGA
(1600 x 1200).
27
4
5
6
7
8
Partial, scrolling
or incorrectly
displayed image
(For notebooks)
The screen of the
notebook
computer is not
displaying your
presentation
Image is unstable
or flickering
Image has vertical
flickering bar
Image is out of
focus
Image is stretched
when displaying a
"widescreen"
DVD title
•
Press "RESYNC" on the remote control or control
panel.
•
For an incorrectly displayed image:
•
Follow the steps for item 2 (above) to adjust
the resolution of your computer.
•
Press the toggle output settings. Example:
[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8],
Gateway [Fn]+[F4], IBM [Fn]+[F7], HP [Fn]+[F4],
NEC [Fn]+[F3], Toshiba [Fn]+[F5 ]
•
If you experience difficulty changing resolutions or
your monitor freezes, restart all equipment
including the projector.
•
If you are using a Microsoft® Windows® based
notebook: Some notebook PCs may deactivate their
own screens when a second display device is in use.
Each has a different way to be reactivated. Refer to
your computer's manual for detailed information.
•
If you are using an Apple® Mac® OS based
notebook: In System Preferences, open Display and
select Video Mirroring "On".
•
Adjust the "Tracking" to correct it. Refer to the
"Image" section for more information.
•
Change the display color depth settings on your
computer.
•
Use "Frequency" to make an adjustment. Refer to
the "Image" section for more information.
•
Check and reconfigure the display mode of your
graphics card to make it compatible with the
projector.
•
•
•
Make sure the lens cap is removed.
Adjusts the focus ring on the projector lens.
Make sure the projection screen is within the
required distance of 4.9 to 32.7 feet (1.5 to 10.0
meters) from the projector. Refer to the "How to
Get a Preferred Image Size by Adjusting Distance
and Zoom" section for more information.
When you play a DVD encoded in anamorphic or 16:9
aspect ratio you may need to adjust the following
settings:
•
If you play a 4:3 format DVD title, please change the
format to 4:3 in the projector OSD.
•
If the image is still stretched, you will also need to
adjust the aspect ratio. Set up the display format to
16:9 (wide) aspect ratio on your DVD player.
•
If you play an Letterbox(LBX) format DVD title,
please change the format to Letterbox(LBX) in the
projector OSD.
English
3
English
28
9
10
11
Image is too small
or too large
Image has slanted
sides
Image is reversed
•
•
Adjust the zoom ring on the top of the projector.
•
Press "MENU" on the remote control or on the
control panel. Go to "Image --> Aspect Ratio" and
try different settings.
•
If possible, reposition the projector so that it is
centered on the screen.
•
Press the "Keystone / " on the OSD or the
remote control until the sides are vertical.
•
Select "Image --> Projection" on the OSD and adjust
the projection direction.
Move the projector closer to or further from the
screen.
Problems with the Projector
#
Condition
Solution
1
The projector stops responding
to all controls
If possible, turn off the projector, then
unplug the power cord and wait at least 30
seconds before reconnecting power.
2
Lamp burns out or makes a
popping sound
When the lamp reaches the end of its useful
life, it will burn out and may make a loud
popping sound. If this happens, the projector
will not turn on until the lamp module has
been replaced. To replace the lamp, follow
the procedures in the "Replacing the Lamp"
section.
29
#
1
Condition
Message
Message Reminder
Fan Fail - the system fan is not working.
Projector Overheated - the projector has exceeded its
recommended operating temperature and must be allowed to
cool down before it may be used.
Replace the lamp - the lamp is about to reach its maximum
lifetime. Prepare to replace it soon.
English
OSD Messages
English
30
LED & Alarm Definition Listing
LED Messages
Message
Power Plug
Standby
Lamp LED
Temp LED
Red
Red
Red
Blue
Flash ON to
OFF 100ms
Flash ON to OFF
100ms
Flash ON to
OFF 100ms
--
--
--
ON
--
--
--
ON
Power button ON
Power LED
Lamp retry
--
--
--
0.5 second
H(On), 0.5
second
L(Off)
flashing
Cooling state
--
--
0.5 second
H(ON), 0.5
second
L(OFF)
flashing
--
Power button OFF: Cooling
completed; Standby Mode
--
--
ON
--
Firmware Download
ON
ON
ON
ON
Thermal Switch error
(T ≤ 105°C) (Lamp Over
Temperature) OSD shows
“Projector Overheated”
--
ON
--
ON
Thermal Switch error
--
ON
--
ON
--
0.5 second
H(On), 0.5
second L(Off)
flashing
--
ON
ON
--
--
ON
0.5 second
H(ON), 0.5
second L(OFF)
flashing
--
--
ON
(T ≥ 105°C) (Lamp Over
Temperature) OSD shows
“Projector Overheated”
Fan lock error OSD shows red
“Fan Fail, Will automatically
turn off soon”
Lamp error (Lamp, ballast)
Color Wheel fail
31
Replacing the dust filters
1
2
3
4
5
Turn the projector off then unplug the power cord.
Pull the both sides dust filters out. (Illustration #1)
Clean or replace the dust filter.
To put the dust filters back, reverse the previous step.
When dust filters are implemented, please set the system to be high
altitude mode. (Settings: Menu->Management->High Altitude->On)
Note: When the dust filters are installed, please make sure the
system is at high altitude mode.
(Illustration #1)
Cleaning the dust filters
Clean the dust filters after every 1000 hours of use. If they are not cleaned
periodically, they can become clogged with dust, preventing proper ventilation.
This can cause overheating and damage the projector. (Normally 1000 hours is
recommended, clean period will be depending on actual environment)
Please find following steps for cleaning procdure:
1
2
To clean the dust filters, use a small vacuum cleaner designed for
computers and other office equipments. It also can be cleaned by water.
(Illustration #2)
If the dirt is difficult to remove or the filter is broken, please contact your
local dealer or service center to obtain a new filter.
Dust Filter
(Illustration #2)
English
Replacing and cleaning the dust filters
English
32
Replacing the Lamp
Use a screwdriver to remove the screw(s) from the cover, and then pull out the
lamp.
The projector will detect the lamp life. You will be shown a warning message
"Lamp is approaching the end of its useful life in full power operation.
Replacement Suggested!" When you see this message, change the lamp as soon
as possible. Make sure the projector has been cooling down for at least 30
minutes before changing the lamp.
Warning: The lamp compartment is hot! Allow it to cool down
before changing the lamp.
3
1
2
1
2
5
4
To Change the Lamp
1
Turn off the projector by pressing the power button.
2
Allow the projector at least 30 mins to cool down.
3
Disconnect the power cord.
4
Remove the two screws on both sides of the projector at the same time.
(Illustration #1)
5
Push and slide the top cover towards the direction of the lens. (Illustration #2)
6
Open the top cover. (Illustration #3)
7
Remove the two screws that secure the lamp moduleX and pull up the
lamp barY.(Illustration #4)
8
Pull out the lamp module by force. (Illustration #5)
To replace the lamp module, reverse the previous step.
Warning: To reduce the risk of personal injury, do not drop the
lamp module or touch the lamp bulb. The bulb may shatter and
cause injury if it is dropped.
33
English
Ceiling Mount Installation
If you wish to install the projector using a ceiling mount, please refer to the
steps below:
Drill four holes into a solid, structurally sound part of the ceiling, and
secure the mount base.
m
m
m
13 m
20
1
mm
130 mm
8.4
.9
49mm
Note: Screws are not included. Please obtain the appropriate
screws for your type of ceiling.
2
Secure the ceiling rod using the appropriate type of four-cylinder screws.
English
34
3
Use the appropriate number of screws for the projector size to attach the
projector to the ceiling mount bracket.
Note: It is recommended that you keep a reasonable space
between the bracket and the projector to allow for proper heat
distribution. Use two washers for extra support, if deemed
necessary.
4
Attach the ceiling bracket to the ceiling rod.
35
Adjust the angle and positioning as necessary.
English
5
30°
Note: The appropriate type of screw and washer for each model is
listed in the table below. 3 mm diameter screws are enclosed in
the screw pack.
Models
Washer Type
Length (mm)
Large
Small
3
25
V
V
SCREW SPEC. M3 x 10 mm
60.0 mm
H6500/E-140/HE-802
Screw Type B
Diameter (mm)
160.0 mm
English
36
Specifications
The specifications listed below are subject to change without notice. For final
specs, please refer to Acer's published marketing specifications.
Projection system
DLP®
Resolution
Native: 1080P (1920 x 1080), Maximum: UXGA (1600 x
1200), WSXGA+ (1680x1050)
Computer compatibility
IBM PC and compatibles, Apple Macintosh, iMac and
VESA standards: SXGA, XGA, VGA, SVGA, SXGA+,
WXGA, WXGA+, WSXGA+
Video compatibility
NTSC (3.58/4.43), PAL (B/D/G/H/I/M/N), SECAM (B/D/G/
K/K1/L), HDTV (720p, 1080i, 1080p), EDTV (480p,
576p), SDTV (480i, 576i)
Aspect ratio
Auto, 4:3, 16:9, L.Box
Displayable colors
1.07 Billion colors
Projection lens
F/ 2.55-2.86, f = 22.37mm - 26.73mm, 1.2X manual
zoom lens
Projection screen size (diagonal)
38" (96 cm) -300" (762 cm)
Projection distance
4.9' (1.5 m) ~ 32.7' (10.0 m)
Throw ratio
60"@2m (1.50 - 1.80:1)
Horizontal scan rate
30k - 100kHz
Vertical refresh scan rate
50 - 85 Hz
Lamp type
240 W user-replaceable lamp
Keystone correction
+/- 15 degrees
Weight
2.54kg (5.6lbs)
Dimensions (W x D x H)
269 mm x 205.6 mm x 95.5 mm (10.6" x 8.1" x 3.8")
Digital Zoom
8X
Power supply
AC input 100 - 240 V, 50 - 60 Hz
Power consumption
305W ± 10% for normal mode
245W ± 10% for ECO mode
Standby< 1W
Operating temperature
5ºC to 35ºC / 41ºF to 95ºF
I/O connectors
•
•
•
•
•
•
•
Power socket x1
VGA input x1
Composite video x1
3 RCA Component video x1
HDMI x2
USB x1: for remote computer control
DC Jack x1
37
•
•
•
•
•
•
•
•
AC power cord x1
VGA cable x1
Remote control x1
Batteries x2 (for remote control)
User's Guide (CD-ROM) x1
Quick start guide x1
Security card x1
Carrying case x1
* Design and specifications are subject to change without notice.
English
Standard package contents
English
38
Compatibility modes
A. VGA Analog
1
VGA Analog - PC Signal
Modes
Resolution
V.Frequency [Hz]
H.Frequency [KHz]
VGA
640x480
640x480
640x480
640x480
800x600
800x600
800x600
800x600
800x600
1024x768
1024x768
1024x768
1024x768
1152x864
1152x864
1152x864
1280x1024
1280x1024
1280x1024
1280x1024
1280x960
1280x960
1400x1050
1600x1200
640x480
640x480
800x600
1024x768
1152x870
1280x960
1024x768
60
72
75
85
56
60
72
75
85
60
70
75
85
70
75
85
60
72
75
85
60
75
60
60
60
66.6(67)
60
60
75
75
75
31.5
37.9
37.5
43.3
35.1
37.9
48.1
46.9
53.7
48.4
56.5
60.0
68.7
63.8
67.5
77.1
64.0
77.0
80.0
91.1
60.0
75.2
65.3
75.00
31.5
34.9
37.9
48.4
68.7
75.2
60.3
SVGA
XGA
SXGA
QuadVGA
SXGA+
UXGA
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
i Mac DV(G3)
39
VGA Analog - Extended Wide timing
Modes
Resolution
V.Frequency [Hz]
H.Frequency [KHz]
WXGA
1280x768
1280x768
1280x768
1280x720
1280x800
1440x900
1680x1050
1366x768
1920x1080
60
75
85
60
60
60
60
60
60
47.8
60.3
68.6
44.8
49.6
55.9
65.3
47.7
67.50
WSXGA+
3
VGA Analog -Component Signal
Modes
Resolution
V.Frequency [Hz]
H.Frequency [KHz]
480i
576i
480p
576p
720p
720p
1080i
1080i
1080p
1080p
1080p
720x480
720x576
720x480
720x576
1280x720
1280x720
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
59.94(29.97)
50(25)
59.94
50
60
50
60(30)
50(25)
23.97/24
60
50
15.7
15.6
31.5
31.3
45.0
37.5
33.8
28.1
27
67.5
56.3
Modes
Resolution
V.Frequency [Hz]
H.Frequency [KHz]
VGA
640x480
640x480
640x480
640x480
800x600
800x600
800x600
800x600
800x600
1024x768
60
72
75
85
56
60
72
75
85
60
31.5
37.9
37.5
43.3
35.1
37.9
48.1
46.9
53.7
48.4
B. HDMI Digital
1
HDMI - PC Signal
SVGA
XGA
English
2
English
40
SXGA
QuadVGA
SXGA+
UXGA
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
i Mac DV(G3)
2
1024x768
1024x768
1024x768
1152x864
1152x864
1152x864
1280x1024
1280x1024
1280x1024
1280x1024
1280x960
1280x960
1400x1050
1600x1200
640x480
640x480
800x600
1024x768
1152x870
1280x960
1024x768
70
75
85
70
75
85
60
72
75
85
60
75
60
60
60
66.6(67)
60
60
75
75
75
56.5
60.0
68.7
63.8
67.5
77.1
64.0
77.0
80.0
91.1
60.0
75.2
65.3
75.00
31.5
34.9
37.9
48.4
68.7
75.2
60.3
HDMI - Extended Wide timing
Modes
Resolution
V.Frequency [Hz]
H.Frequency [KHz]
WXGA
1280x768
1280x768
1280x768
1280x720
1280x800
1440x900
1680x1050
1366x768
1920x1080
60
75
85
60
60
60
60
60
60
47.8
60.3
68.6
44.8
49.6
55.9
65.3
47.7
67.50
WSXGA+
41
HDMI - Video Signal
Modes
Resolution
V.Frequency [Hz]
H.Frequency [KHz]
15.7
480i
720x480(1440x480)
59.94(29.97)
480p
720x480
59.94
31.5
576i
720x576(1440x576)
50(25)
15.6
576p
720x576
50
31.3
720p
1280x720
60
45.0
720p
1280x720
50
37.5
1080i
1920x1080
60(30)
33.8
1080i
1920x1080
50(25)
28.1
1080p
1920x1080
23.97/24
27
1080p
1920x1080
60
67.5
1080p
1920x1080
50
56.3
Graphic source Horizontal scan
monitor range rate:
limits
Vertical scan rate:
30k-100kHz
50-85Hz
ADC
Max. pixel rate:
170MHz
TMDS
Max. frequency:
200MHz
English
3
English
42
Regulations and safety notices
FCC notice
This device has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This device generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television
reception, which can be determined by turning the device off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the device and receiver.
•
Connect the device into an outlet on a circuit different from that to which
the receiver is connected.
•
Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables
to maintain compliance with FCC regulations.
Notice: Peripheral devices
Only peripherals (input/output devices, terminals, printers, etc.) certified to
comply with the Class B limits may be attached to this equipment. Operation
with non-certified peripherals is likely to result in interference to radio and TV
reception.
Caution
Changes or modifications not expressly approved by the manufacturer could
void the user's authority, which is granted by the Federal Communications
Commission, to operate this device.
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme a la norme NMB-003 du
Canada.
Declaration of Conformity for EU countries
Acer hereby declares that this projector series is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Compliant with Russian regulatory certification
Radio device regulatory notice
Note: The regulatory information below is for models with
wireless LAN and/or Bluetooth only.
General
This product complies with the radio frequency and safety standards of any
country or region in which it has been approved for wireless use. Depending on
configurations, this product may or may not contain wireless radio devices (such
as wireless LAN and/or Bluetooth modules).
Canada — Low-power license-exempt radio
communication devices (RSS-210)
a
Common information
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference
that may cause undesired operation of the device.
b
Operation in 2.4 GHz band
To prevent radio interference to the licensed service, this device is
intended to be operated indoors and installation outdoors is subject
to licensing.
List of applicable countries
This device must be used in strict accordance with the regulations and constraints in the
country of use. For further information, please contact the local office in the country of use.
Please see http://ec.europa.eu/enterprise/rtte/implem.htm for the latest country list.
English
Remarque à l'intention des utilisateurs canadiens
English
43
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi,
New Taipei City 221,Taiwan, R.O.C.
Declaration of Conformity
We,
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221,Taiwan, R.O.C.
Contact Person: Mr. Easy Lai, e-mail:easy_lai@acer.com.tw
And,
Acer Italy s.r.l
Via Lepetit, 40, 20020 Lainate (MI) Italy
Tel: +39-02-939-921, Fax: +39-02 9399-2913, www.acer.it
Hereby declare that:
Product:
Trade Name:
Model Number:
Machine Type:
Projector
Acer
M1P1108
H6500/E140/HE-802
Is compliant with the essential requirements and other relevant provisions of the following EC
directives, and that all the necessary steps have been taken and are in force to assure that
production units of the same product will continue comply with the requirements.
EMC Directive 2004/108/EC as attested by conformity with the following
harmonized standards:
-. EN55022, AS/NZS CISPR22, Class B
-. EN55024
-. EN61000-3-2 Class A
-. EN61000-3-3
Low Voltage Directive 2006/95/EC as attested by conformity with the following
harmonized standard:
-. EN60950-1
RoHS Directive 2002/95/EC on the Restriction of the Use of certain Hazardous
Substances in Electrical and Electronic Equipment
-. The maximum concentration values of the restricted substances by weight in homogenous
material are:
Lead
Mercury
Hexavalent Chromium
!
0.1%
0.1%
0.1%
Polybrominated Biphenyls (PBB’s)
Polybrominated Diphenyl Ethers (PBDE’s)
Cadmium
0.1%
0.1%
0.01%
Directive 2009/125/EC with regard to establishing a framework for the setting
of ecodesign requirements for energy-related product.
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi,
New Taipei City 221,Taiwan, R.O.C.
The standards listed below are applied to the product if built with WLAN
module or wireless keyboard and mouse.
R&TTE Directive 1999/5/EC as attested by conformity with the following
harmonized standard:
z Article 3.1(a) Health and Safety
-. EN60950-1
-. EN62311
z Article 3.1(b) EMC
-. EN301 489-1
-. EN301 489-17
z Article 3.2 Spectrum Usages
-. EN300 328
-. EN301 893 (Applicable to 5GHz high performance RLAN).
Year to begin affixing CE marking 2011.
_______________________________
Aug. 24, 2011
Easy Lai /Manager
Date
Regulation Center, Acer Inc.
-
Acer America Corporation
333 West San Carlos St., San Jose
CA 95110, U. S. A.
Tel : 254-298-4000
Fax : 254-298-4147
www.acer.com
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
The following local Manufacturer / Importer is responsible for this declaration:
Product:
DLP Projector
Model Number:
M1P1108
Machine Type:
H6500/E140/HE-802
Name of Responsible Party:
Acer America Corporation
Address of Responsible Party:
333 West San Carlos St.
San Jose, CA 95110
U. S. A.
Contact Person:
Acer Representative
Phone No.:
254-298-4000
Fax No.:
254-298-4147