Compaq CONTURA AERO Specifications

4mb−Laptops
4mb−Laptops
Table of Contents
4mb Laptop HOWTO.........................................................................................................................................1
Bruce Richardson <brichardson@lineone.net> ......................................................................................1
1.Introduction...........................................................................................................................................1
2.The Laptops..........................................................................................................................................1
3.Choices Made........................................................................................................................................1
4.The Pre−installation Procedure.............................................................................................................2
5.The Installation.....................................................................................................................................2
6.Conclusion............................................................................................................................................2
7.Appendix A: .........................................................................................................................................2
8.Appendix B: Resources relevant to this HOWTO................................................................................2
1.Introduction...........................................................................................................................................2
1.1 Why this document was written.........................................................................................................3
1.2 What use is a small laptop?................................................................................................................3
1.3 Why not just upgrade the laptop?......................................................................................................3
1.4 What about 4mb desktop machines?..................................................................................................3
1.5 What this document doesn't do..........................................................................................................3
1.6 Where to find this document..............................................................................................................3
1.7 Copyright...........................................................................................................................................3
2.The Laptops..........................................................................................................................................4
2.1 Basic Specifications...........................................................................................................................4
Compaq Contura Aero ...............................................................................................................4
Toshiba T1910 ...........................................................................................................................4
2.2 The Problem.......................................................................................................................................5
2.3 The Solution.......................................................................................................................................5
3.Choices Made........................................................................................................................................5
3.1 What to use to create the initial root partition?..................................................................................5
3.2 The Distribution.................................................................................................................................6
But I don't like Slackware! ........................................................................................................6
3.3 Which installation method to use?.....................................................................................................6
3.4 Partition Layout.................................................................................................................................7
Basic Requirement .....................................................................................................................7
How complex a layout? .............................................................................................................7
3.5 Which components to install?............................................................................................................8
4.The Pre−installation Procedure.............................................................................................................8
4.1 muLinux Preparation.........................................................................................................................8
4.2 Prepare the installation root files.......................................................................................................8
4.3 Create the partitions...........................................................................................................................9
Mini−Linuces and ext2 file−systems − an important note. .......................................................9
Procedure ...................................................................................................................................9
5.The Installation...................................................................................................................................10
5.1 Boot the machine.............................................................................................................................10
5.2 Floppy/Parport CD−ROM Install....................................................................................................10
5.3 Network/PCMCIA Install................................................................................................................10
PCMCIA install on the Aero ...................................................................................................11
5.4 Set−up..............................................................................................................................................11
AddSwap ..................................................................................................................................11
Target .......................................................................................................................................11
i
4mb−Laptops
Table of Contents
Select........................................................................................................................................11
Install ......................................................................................................................................12
Configure .................................................................................................................................12
Exit ...........................................................................................................................................12
5.5 Pre−reboot Configuration................................................................................................................12
5.6 Post−reboot Configuration...............................................................................................................13
Re−use the temporary root.......................................................................................................13
Other configuration tweaks. .....................................................................................................13
6.Conclusion..........................................................................................................................................13
7.Appendix A: .......................................................................................................................................14
7.1 A − Base Linux System...................................................................................................................14
Packages considered for omission: ..........................................................................................14
Packages installed: ...................................................................................................................15
7.2 AP − Non−X Applications...............................................................................................................16
Packages considered for inclusion: ..........................................................................................16
Packages installed: ...................................................................................................................17
7.3 D − Development Tools...................................................................................................................17
Packages installed: ...................................................................................................................18
7.4 E − Emacs........................................................................................................................................18
Packages installed: ...................................................................................................................18
7.5 F − FAQs and HOWTOs.................................................................................................................18
Packages installed: ...................................................................................................................18
7.6 K − Kernel Source...........................................................................................................................18
Packages Installed: ...................................................................................................................18
7.7 N − Networking Tools and Apps.....................................................................................................18
Packages installed: ...................................................................................................................18
7.8 Tetex................................................................................................................................................19
Packages installed: ...................................................................................................................19
7.9 Y − BSD Games Collection.............................................................................................................19
Packages installed: ...................................................................................................................19
7.10 End result.......................................................................................................................................19
8.Appendix B: Resources relevant to this HOWTO..............................................................................19
ii
4mb Laptop HOWTO
Bruce Richardson <brichardson@lineone.net>
25 March 2000
How to put a "grown−up" Linux on a small−spec (4mb RAM, <=200mb hard disk) laptop.
1.Introduction
• 1.1 Why this document was written.
• 1.2 What use is a small laptop?
• 1.3 Why not just upgrade the laptop?
• 1.4 What about 4mb desktop machines?
• 1.5 What this document doesn't do.
• 1.6 Where to find this document.
• 1.7 Copyright
2.The Laptops
• 2.1 Basic Specifications
• 2.2 The Problem
• 2.3 The Solution
3.Choices Made
• 3.1 What to use to create the initial root partition?
• 3.2 The Distribution
• 3.3 Which installation method to use?
• 3.4 Partition Layout
• 3.5 Which components to install?
4mb Laptop HOWTO
1
4mb−Laptops
4.The Pre−installation Procedure
• 4.1 muLinux Preparation
• 4.2 Prepare the installation root files.
• 4.3 Create the partitions.
5.The Installation
• 5.1 Boot the machine
• 5.2 Floppy/Parport CD−ROM Install
• 5.3 Network/PCMCIA Install
• 5.4 Set−up
• 5.5 Pre−reboot Configuration
• 5.6 Post−reboot Configuration.
6.Conclusion
7.Appendix A:
• 7.1 A − Base Linux System
• 7.2 AP − Non−X Applications
• 7.3 D − Development Tools
• 7.4 E − Emacs
• 7.5 F − FAQs and HOWTOs
• 7.6 K − Kernel Source
• 7.7 N − Networking Tools and Apps
• 7.8 Tetex
• 7.9 Y − BSD Games Collection
• 7.10 End result
8.Appendix B: Resources relevant to this HOWTO
1.Introduction
4.The Pre−installation Procedure
2
4mb−Laptops
1.1 Why this document was written.
I got my hands on two elderly laptops, both with just 4mb RAM and small (<=200mb) hard drives. I wanted
to install Linux on them. The documentation for this kind of laptop all recommends installing either a
mini−Linux or an old (and therefor compact) version of one of the professional distributions. I wanted to
install an up−to−date professional distribution.
1.2 What use is a small laptop?
Plenty. It isn't going to run X or be a development box (see Which components to install?) but if you are
happy at the console you have a machine that can do e−mail, networking, writing etc. Laptops also make
excellent diagnostic/repair tools and the utilities for that will easily fit onto small laptops.
1.3 Why not just upgrade the laptop?
Upgrading old laptops is not much cheaper than upgrading new ones. That's a lot to spend on an old machine,
especially considering that the manufacturer isn't supporting it any more and spare parts are hard to find.
1.4 What about 4mb desktop machines?
The procedure described in this document will work perfectly well on a desktop PC. On the other hand,
upgrading a desktop machine is far easier and cheaper than upgrading a laptop. Even if you don't upgrade it,
there are still simpler options. You could take out the hard disk, put it in a more powerful machine, install
Linux, trim it to fit and then put the disk back in the old machine.
1.5 What this document doesn't do.
This document is not a general HOWTO about installing Linux on laptops or even a specific HOWTO for
either of the two machines mentioned here. It simply describes a way of squeezing a large Linux into a very
small space, citing two specific machines as examples.
1.6 Where to find this document.
The latest copy of this document can be found in several formats at
http://website.lineone.net/~brichardson/linux/4mb_laptops/.
1.7 Copyright
This document is copyright (c) Bruce Richardson 2000. It may be distributed under the terms set forth in the
LDP license at sunsite.unc.edu/LDP/COPYRIGHT.html.
This HOWTO is free documentation; you can redistribute it and/or modify it under the terms of the LDP
license. This document is distributed in the hope that it will be useful, but without any warranty; without even
the implied warranty of merchantability or fitness for a particular purpose. See the LDP license for more
1.1 Why this document was written.
3
4mb−Laptops
details.
Toshiba and T1910 are trademarks of Toshiba Corporation. Compaq and Contura Aero are trademarks of
Compaq Computer Corporation.
2.The Laptops
This section describes the laptops that I have used this procedure on, the problems faced when installing
Linux on them and the solutions to those problems (in outline).
2.1 Basic Specifications
Compaq Contura Aero
• 25MHz 486SX CPU
• 4mb RAM
• 170mb Hard Disk
• 1 PCMCIA Type II slot
• External PCMCIA 3.5" Floppy drive
The PCMCIA floppy drive has a proprietary interface which is partly handled by the
Aero's unique BIOS. The Linux PCMCIA drivers can't work with it. According to
the PCMCIA−HOWTO, if the drive is connected when the laptop boots it will work
as a standard drive and Card Services will ignore the socket but it is not
hot−swappable. However, I found that the drive becomes inaccessible as soon as
Card Services start unless there is a mounted disk in the drive. This has implications
for the installation process − these are covered at the relevant points.
Toshiba T1910
• 33MHz 486SX CPU
• 4mb RAM
• 200 mb Hard Disk
• Internal 3.5" Floppy drive
• 1 PCMCIA Type II/III slot
2.The Laptops
4
4mb−Laptops
2.2 The Problem
The small hard disks and the lack of an internal floppy on the Aero make the installation more tricky than
normal but the real problem is the RAM. None of the current distributions has an installation disk that will
boot in 4mb, not even if the whole hard disk is a swap partition.
The standard installation uses a boot disk to uncompress a root−partition image (either from a second floppy
or from CD−ROM) into a ram−disk. The root−image is around 4mb in size. That's all the RAM available in
this scenario. Try it and it freezes while unpacking the root−image.
2.3 The Solution
The answer is to eliminate the ram−disk. If you can mount root on a physical partition you will have enough
memory to do the install. Since the uncompressed ram−disk is too big to fit on a floppy, the only place left is
on the hard disk of the laptop. The steps are:
1. Find something that will boot in 4mb ram and which can also create ext2 partitions.
2. Use it to create a swap partition and a small ext2 partition on the laptop's hard disk.
3. Uncompress the installation root−image and copy it onto the ext2 partition.
4. Boot the laptop from the installation boot−disk, pointing it at the ext2 partition on the hard disk.
5. The installation should go more or less as normal from here.
The only question was whether a distribution that wouldn't install (under normal circumstances) on the
laptops would run on them. The short answer is "Yes".
If you're an old Linux hand then that's all you need to know. If not, read on − some of the steps listed above
aren't as simple as they look.
3.Choices Made
This section describes the choices available, which options are practical, which ones I decided on and why.
3.1 What to use to create the initial root partition?
The best tool for this is a mini−Linux. There's a wide selection of small Linuces available on the net, but most
of them won't boot in 4mb RAM. I found two that will:
SmallLinux http://smalllinux.netpedia.net/
SmallLinux will boot in as little as 2mb RAM but its root disk can't be taken out of the drive,
which is a shame since otherwise it has everything we need (i.e. fdisk, mkswap and
mkfs.ext2). SmallLinux can create the needed partitions but can't be used to copy the root
partition.
2.2 The Problem
5
4mb−Laptops
muLinux http://sunsite.auc.dk/mulinux/
muLinux will boot in 4mb but only in a limited single−user mode. In this mode fdisk and
mkswap are available but mkfs.ext2 and the libraries needed to run it are on the /usr partition
which is not available in maintenance mode. To use muLinux to do the whole
pre−installation procedure the files needed to create ext2 file−systems must be extracted
from the usr disk image and copied onto a floppy.
This gives the option of either using SmallLinux to create the partitions and muLinux to copy the root
partition or using muLinux to do the whole job. Since I had two laptops I tried both.
3.2 The Distribution
It didn't take much time to choose Slackware. Apart from the fact that I like it but haven't used it much and
want to learn more, I considered the following points:
• Slackware has possibly the most low−tech DIY install of all the major distributions. It is also one of
the most flexible, coming with a wide range of boot−disk kernels to suit many different machines.
This makes it well suited to the kind of hacking about required in this scenario.
• Slackware supports all the methods listed in Which Installation method to use?.
• Slackware is a distribution designed by one person. I'm sure Patrick Volkerding won't object if I say
this means its configuration tools are simpler and more streamlined. In my opinion this makes the job
of trimming the installation to fit cramped conditions easier.
Version 7.0 was the latest version when I tried this so that's what I used.
But I don't like Slackware!
You don't have to use it. I can't answer for all the distributions but I know that Debian, Red Hat and SuSE
offer a range of installation methods and have an "expert" installation procedure
Does Debian do any other kind?
which can be used here. Most of the steps in this document would apply to any of the distributions without
change.
If you haven't used the expert method with your preferred distribution before, do a trial run on a simple
desktop machine to get the feel of it and to explore the options it offers.
3.3 Which installation method to use?
Floppy Install
This means churning out 15 floppies − which only gives you an absolute minimal install and
requires a second stage to get the apps you want on. It's also very slow on such low−spec
machines. This is a last resort if you can't make the others work.
3.2 The Distribution
6
4mb−Laptops
Parallel−port Install
Where the parallel port has an IDE device, parallel cable or pocket ethernet adaptor A pocket
lan adaptor installation onto these machines will be very slow. attached. This would be a
good choice for the Aero, leaving the PCMCIA slot free to run the floppy drive.
PCMCIA Install
As above, this could be a CD−ROM or network install. This would be the best method for
the T1910 − on the Aero it's a bit more awkward.
ISA/PCI Ethernet Install
Not an option for the laptops, obviously, but included in case your target machine is a
desktop PC.
The tools I had to hand dictated a PCMCIA network install. I will point out where steps
differ for the other methods. Whichever method you choose, you need to have a higher−spec
machine available − even if only to create the disks for a floppy install.
3.4 Partition Layout
Basic Requirement
This procedure requires at least two Linux Native partitions in addition to a Swap partition. Since one of the
ext2 partitions will be in use as temporary root during the installation it will not be available as a target
partition and so should be small − though no smaller than 5mb. It makes sense to create for this a partition
that you will re−use as /home after installation is complete. Another option would be to re−create it as a DOS
partition to give you a dual boot laptop.
How complex a layout?
There isn't room to get too clever here. There is an argument for having a single ext2 partition and using a
swap file to avoid wasting space but I would strongly urge creating a separate partition for /usr. If you have
only one partition and something goes wrong with it you may well be faced with a complete re−installation.
Separating /usr and having a small partition for / makes disaster recovery a more likely prospect. On both
machines I created 4 partitions in total:
1. A swap partition −− 16mb on the T1910, 20 on the Aero (I'm more likely to upgrade the memory on
the Aero).
2. /home (temporary root during installation) −− 10mb
3. / −− 40mb on the T1910, 30mb on the Aero.
4. /usr −− All the remainder.
3.4 Partition Layout
7
4mb−Laptops
In addition, the Aero uses hda3 for a 2mb DOS partition containing configuration utilities. See the Aero
FAQs for details.
3.5 Which components to install?
The full glibc libraries alone would nearly fill the hard disks so there's no question of building a development
machine. It looks as if a minimal X installation can be squeezed in but I'm sure it would crawl and I don't
want it anyway. I decide to install the following (for a full listing see Appendix A):
• The core Linux utilities
• Assorted text apps from the ap1 file set:
• Info/FAQ/HOWTO documentation
• Basic networking utilities
• The BSD games
This selection matches the kind of machine described in What use is a small laptop?.
4.The Pre−installation Procedure
This section covers creating a swap partition and a temporary root partition on the laptop's hard disk. Nothing
here is Slackware−specific.
4.1 muLinux Preparation
If you are going to use only muLinux to for this procedure then you need to prepare a disk with mkfs.ext2
and supporting libraries on it. From the muLinux setup files uncompress USR.bz2 and mount it as a loop
file−system. If you are in the same directory as the USR file and you want to mount it as /tmpusr then the
sequence for this is:
losetup /dev/loop0 USR
mount −t ext2 /dev/loop0 /tmpusr
>From there copy mkfs.ext2, libext2fs.so.2, libcomerr.so.2 and libuuid.so.1 onto a floppy.
4.2 Prepare the installation root files.
Select the root disk you want − I used the color one with no problems but the text one would be slightly faster
in these low memory conditions. Uncompress the image and mount it as a loop device. The procedure is the
same as in the above section but the root disk image is a minix file−system.
Next you need 3 1722 floppies or 4 1440 floppies with ext2 file−systems − it's better with 1722 disks as you
don't need to split the /lib directory. Give one floppy twice the default number of inodes so it can take the
3.5 Which components to install?
8
4mb−Laptops
/dev directory. That's 432 nodes for a 1722 disk or 368 for a 1440. If you specify /dev/fd0H1722 or
/dev/fd0H1440 then you don't have to give any other parameters so for a 1722 disk do
mke2fs −N 432 /dev/fd0H1722
If you have mounted the root image as /tmproot and the destination floppy as /floppy then cd to /tmproot. To
copy the dev directory the command is
cp −dpPR dev/* /floppy/
For the other directories with files in (bin, etc, lib, mnt, sbin, usr, var) it's
cp −dpPr directoryname/* /floppy/
Don't bother with the empty ones (floppy, proc, root, tag, tmp) because you can simply create them on the
laptop. boot and cdrom are soft links pointing to /mnt/boot and /var/log/mount respectively − you can also
create them on the laptop.
4.3 Create the partitions.
Mini−Linuces and ext2 file−systems − an important note.
To save space, small−Linux designers sometimes use older libc5 librariesand where they do use up−to−date
libc6 they leave out may of the options compiled into full distributions, including some optional features of
the ext2 file−system. This has two consequences:
• Trying to mount ext2 disks formatted using a modern Linux system can generate error messages if
you mount them read−write. Be sure to use the −r option when mounting floppies on the laptops.
• It is not wise to use the mkfs.ext2 that comes with the mini−Linux to create file−systems on the
partitions into which SlackWare will be installed. It should only be used to create the file−system on
the temporary root partition. Once installation is complete this partition can be reformatted and
re−used.
Procedure
If installing on an Aero, make sure the floppy drive is inserted before switching on and do not remove it.
1. Boot from the mini−Linux
4.3 Create the partitions.
9
4mb−Laptops
With muLinux, wait until the boot−process complains about the small memory space
and offers the option of dropping into a shell − take that option and work in the
limited single−user mode it gives you.
2. Use fdisk to create the partitions.
3. Reboot on leaving fdisk (with muLinux you may simply have to turn off and on again at this point).
4. Use mkswap on the swap partition and then activate it (this will make muLinux much happier).
5. If using muLinux then mount the extra floppy created in muLinux Preparation, copy mkfs.ext2 into
/bin and the libraries into /lib.
6. Use mkfs.ext2 to create the file−system on the temporary root partition.
7. If you have been using SmallLinux, shut down and reboot using muLinux. Don't forget to activate the
swap partition again.
8. muLinux will have mounted the boot floppy on /startup − unmount it to free the floppy drive.
9. Now mount the temporary root partition and copy onto it the contents of the disks you created in
Prepare the installation root files. Do not be alarmed by the error messages: if, for example, you copy
usr from the floppy to the temporary root partition by typing "cp −dpPr usr/* /tmproot/" then you'll
get the error message "cp: sr: no such file or directory". Ignore this, nothing is wrong.
10. cd to the temporary root partition and create the empty folders (floppy, proc, root, tag, tmp) and the
soft links boot (pointing to mnt/boot) and cdrom (to var/log/mount).
11. Unmount the temporary root partition − this syncs the disk.
12. You can simply turn off the machine now.
5.The Installation
This section does not give much detail on the Slackware installation process. In fact, it assumes you are
familiar with it. Instead, this section concentrates on those areas where special care or unusual steps are
required.
5.1 Boot the machine
Make a boot−disk from one of the images. I recommend you use bareapm.i on a laptop and bare.i on a
desktop − unless you have a parallel−port IDE device (pportide.i). Boot the laptop from it. When the boot:
prompt appears, type "mount root=/dev/hdax" where x is the temporary root partition. Log in as root. Then
activate the swap partition.
5.2 Floppy/Parport CD−ROM Install
In both these cases, no extra work should be necessary to access the installation media. Simply run setup.
5.3 Network/PCMCIA Install
Slackware has supplementary disks with tools for these and instructions for their use greet you when you log
in. Use the network disk on a desktop PC with ethernet card or a laptop with pocket ethernet adaptor. Use the
PCMCIA disk for PCMCIA install. Once your network adapter/PCMCIA socket has been identified, run
setup.
5.The Installation
10
4mb−Laptops
PCMCIA install on the Aero
The Slackware installation process runs the PCMCIA drivers from the supplementary floppy. Because the
Aero has a PCMCIA floppy drive, this means you can't remove the floppy drive to insert the PCMCIA
CD−ROM/ethernet card. The solution is simple: the Slackware PCMCIA setup routine creates /pcmcia and
mounts the supplementary disk there, so
1. Create the /pcmcia directory yourself
2. Mount the supplementary disk to /mnt. Be sure to specify the type as vfat − if you don't, it'll be
incorrectly identified as UMSDOS and long filenames will be mis−copied.
3. cd /mnt;cp −dpPr ./* /pcmcia/
4. Unmount the floppy.
5. Run pcmcia. When the script complains that there is no disk in the drive simply hit Enter: Card
Sevices will start. Connect your PCMCIA device and hit Enter.
6. Run setup
5.4 Set−up
The Slackware set−up program is straightforward. Start with the Keymap section and it'll take you forward
step by step.
AddSwap
You do need to do this step so it can put the correct entry in fstab but make sure it doesn't run mkswap −
you're already using the partition.
Target
In this section Slackware asks which partitions will be mounted as what and then formats them if you want.
The safest bet here is to leave your temporary root partition out altogether and just edit fstab later once you
know you don't need it for it's temporary purpose anymore. If you're going to reuse it as /home then it is OK
to designate it as /home − obviously, don't format it now! If you intend to re−use it as a part of the directory
structure that will have files placed in it during installation (/var, for example) then you absolutely must
ignore it in this step: after the installation is complete you can move the files across.
Select
Here you choose which general categories of software to install. I chose as follows:
• A − Base Linux System
• AP −Non−X applications
• F − FAQs and HOWTOs
• N − Networking tools and apps
• Y − BSD games collection
PCMCIA install on the Aero
11
4mb−Laptops
I wouldn't recommend adding to this − if anything, prune it back to A, AP and N. That gives you a core
Linux setup to which you can add according to your needs.
Install
Choose the Expert installation method. This allows you to select/reject for installation individual packages
from the categories you chose in the Selection step. Appendix A goes through the precise choices I made .
This part takes about 3 hours for a PCMCIA network install. You are prompted to select individual packages
before the installation of each category, so you can't just walk away and leave it to run through.
Configure
Once the packages are all installed, you are prompted to do final configuration for your machine. This covers
areas like networking, Lilo, selecting a kernel etc. Some points to look out for:
• If you did a PCMCIA install, don't accept the offer to configure your network with netconfig. This
will ruin your pcmcia networking. Wait until you've rebooted and then edit /etc/pcmcia/network.opts
• This is the point where you should install a kernel. For a laptop the bareapm kernel is best, for a
desktop simply the bare one.
Exit
The set−up process is finished but you are not. Do not reboot yet! There is another vital step to complete.
5.5 Pre−reboot Configuration
On a normal machine you would simply reboot once the installation is complete. If you do that here you may
have to wait 6 or 8 hours for a login prompt to appear and another half hour to get to the command prompt.
Before rebooting you need to change or remove the elements that cause this slowdown. This involves editing
config files so you need to be familiar with vi, ed or sed.
At this stage your future root partition is still mounted as /mnt so remember to at that to the paths given here.
/etc/passwd
Edit this to change root's login shell to ash. ash really is the only practical login shell for 4mb
RAM.
/etc/rc.d/rc.modules
Comment out the line 'depmod −a'. You only need to update module dependencies if you
have changed your module configuration (recompiled or added new ones, for example). On a
standard system it only takes a second or two and so it doesn't matter that it's needlessly
performed each time. On a 4mb laptop it can take as much as 8 hours. When you do change
your module set−up you can simply uncomment this line and reboot. Alternatively, change
Install
12
4mb−Laptops
this part of the script so that it will only run if you pass a parameter at the boot−prompt. For
example:
if [ "NEWMODULES" == "1" ] ; then
depmod −afi
/etc/rc.d/rc.inet2
This script starts network services like nfs. You probably don't need these and certainly not at
start−up. Rename this script to something like RC.inet2 − that will stop it from being run at
boot and you can run it manually when you need it.
/etc/rc.d/rc.pcmcia
On the Aero you should also rename this script, otherwise you'll lose the use of your floppy
drive on start−up. It's worth considering for any other small laptop as well − you can always
run it manually before inserting a card.
Once these changes have been made, you are ready to reboot.
5.6 Post−reboot Configuration.
If you made the changes recommended in section Pre−reboot configuration then the boot process will only
take a few minutes, as opposed to several hours. Login as root and check that everything is functioning
properly.
Re−use the temporary root.
Once you are sure the installation is solid you can reclaim the partition you used as the temporary root. Don't
just delete the contents, reformat the filesystem. Remember, the mke2fs that came with the mini−Linux is out
of date.
If you intend to re−use this partition as /home, remember not to create any user accounts until you have
completed this step.
Other configuration tweaks.
In such a small RAM space, every little helps. Go through SlackWare's BSD−style init scripts in /etc/rc.d/
and comment out anything you don't need. Have a look at Todd Burgess' Small Memory mini−HOWTO
http://eddie.cis.uoguelph.ca/~tburgess/ for more ideas.
6.Conclusion
That's it all done. You now have a laptop with the core utilities in place and 50 to 70mb spare for whichever
extras you need. Don't mess it up because it's a lot easier to modify an existing installation on such cramped
old machines than it is to start from scratch again.
5.6 Post−reboot Configuration.
13
4mb−Laptops
7.Appendix A:
This appendix lists which packages (if any) from each category might be included in the installation and
gives my reasons for including or omitting them. I made no attempt to install X so those categories are
ignored.
Although this appendix refers specifically to the Slackware distribution it can be used as a guide with any of
the major distributions.
7.1 A − Base Linux System
Most of the packages in this category are essential, even those that aren't listed as required by the Slackware
set−up program. Because of this, I've listed those packages that I felt could reasonably be left out rather than
all the non−compulsory packages that I installed.
Packages considered for omission:
kernels (ide, scsi etc.)
There's no need to install any of these, you get a chance to select a kernel at the very end of
the installation process.
aoutlibs
This is only needed if you intend to run executables compiled in the old a.out format.
Omitting it saves a lot of space. Omitted.
bash1
Bash2 (simply called bash in the Slackware package list) is required for the Slackware
configuration scripts but there are a lot of scripts that need bash1. I included it.
getty
agetty is Slackware's default getty, this package contains getty and uugetty as alternatives.
Only include it if you need their extra functionality. Omitted.
gpm
Personally, I find this very useful at the console (and the Aero's trackball is very handy) but
it's not essential. Included.
icbs2
Not needed. Omitted.
isapnp
7.Appendix A:
14
4mb−Laptops
No use here. Omitted.
loadlin
Not needed with the setup described here − unless your old laptop has some peculiarity that
requires a DOS driver to initialise some of its devices. Omitted.
lpr
You could argue that you can do your printing from whichever desktop is nearest but I
always find it useful to be have printing capabilities on a laptop. Included.
minicom
Not a compulsory include but I want the laptop to do dial−up connection. Very handy.
Included.
pciutils
Not needed on these old laptops. Omitted.
quota
Not vital but it can be used to set limits that stop you from overflowing the limited space
available in these laptops. Included.
tcsh
I recommend using ash as your login shell. Only include this if you need it for scripts.
Omitted.
umsprogs
You can leave this out and still be able to access UMSDOS floppies. Omitted.
scsimods
No use on these laptops. Omitted.
sysklogd
This can interfere with apmd but it does provide essential information. Included.
Packages installed:
aaa_base, bash, bash1, bin, bzip2, cpio, cxxlibs, devs, e2fsprog, elflibs, elvis, etc, fileutils, find, floppy,
fsmods, glibcso, gpm, grep, gzip, hdsetup, infozip, kbd, ldso, less, lilo, man, modules, modutils, pcmcia,
sh_utils, shadow, sudo, sysklogd, sysvinit, tar, txtutils, util, zoneinfo
Combined size: 33.4
Packages installed:
15
4mb−Laptops
7.2 AP − Non−X Applications
None of these packages are, strictly speaking, essential − although ash is really required for sensible
operation in 4mb. Leaving them all out could save the vital space for you to squeeze in your favourite app. I
selected a minimal set of tools that I don't like to do without.
Packages considered for inclusion:
apsfilter
Not much point having printing if you can only print text files. Included.
ash
This is the shell for low−memory machines, only taking up 60k. Use it as the default login
shell unless you like waiting 10 seconds for the command prompt to reappear each time.
Included.
editors (jed, joe jove vim)
elvis is the default Slackware editor and a required part of the installation. If, like me, you are
a vi fan then that's all you need: installing vim would be wasteful duplication given the space
restrictions. If you can't stand vi and need a more DOS−style editor then joe is small. Emacs
fans with some self−discipline might consider jed or jove rather than pigging out on the
full−size beast. Omitted.
enscript
If you already have apsfilter you don't really need this. Omitted.
ghostscript
Including the fonts this comes to about 7.5mb. One to leave until after the core installation,
then consider if you need it. Omitted.
groff
Needed for the man pages. Included.
ispell
Not an essential butvery useful to the overenthusiastic touch−typist. included.
manpages
Included!
mc
7.2 AP − Non−X Applications
16
4mb−Laptops
Slackware offers a lightweight compilation of mc but I'm happier at the command prompt.
Omitted.
quota
Not necessary on what is not a multi−user machine but you may,like me, find it handy to
stop you from forgetfully wasting the little space you have. Included.
rpm
Don't bother. If you do have an rpm that you would like to squeeze in, use rpm2tgz on a
desktop machine to turn it into a tgz package − then you can use the standard Slackware
installation tools. Omitted.
sc
A useful little spreadsheet packed very small. Included.
sudo
Not essential but I find it useful here: it's a cramped environment and an awkward reinstall if
you mess things up − sudo helps create user profiles with the power to do the things you need
without carelessly wiping your disk. Included.
texinfo
Info documentation. Included.
zsh
Leave this out unless you're addicted to it or have scripts that must use it. Omitted.
Packages installed:
apsfilter,ash, diff, groff, ispell, manpages, quota, sc, sudo, texinfo
Combined size: 8.1 mb
7.3 D − Development Tools
You could fit C or C++ into this space but the glibc library package is too big, so some pruning would be
needed. Do the main installation first and then try it.
There is room for Perl and Python.
Packages installed:
17
4mb−Laptops
Packages installed:
None
7.4 E − Emacs
I don't use Emacs and so saved myself some space. On the other hand, if you are an Emacs fan then you
probably use it for e−mail, news and coding so you'll claim some of that space back by omitting other
packages.
If you do want Emacs it might be an idea to leave this out while doing the core installation. Once the laptop is
up you can try fitting in what you want/need at your leisure.
Packages installed:
None.
7.5 F − FAQs and HOWTOs
If you know it all you don't need these. I installed the lot.
Packages installed:
howto, manyfaqs, mini
Combined size: 12.4 mb
7.6 K − Kernel Source
You can just squeeze it in. If all you want to do is read the source, go ahead.
Packages Installed:
None
7.7 N − Networking Tools and Apps
These packages were selected to provide core networking tools, dial−up capability, e−mail, web and news.
Packages installed:
dip, elm, fetchmail, mailx, lynx, netmods, netpipes, ppp, procmail, trn, tcpip1, tcpip2, uucp, wget
Combined size: 15.1 mb
Packages installed:
18
4mb−Laptops
7.8 Tetex
Another set that will barely squeeze in. I can't say how it would run in the space available.
Packages installed:
None
7.9 Y − BSD Games Collection
I'm addicted to several of these. If I really need that last 5mb they can go.
Packages installed:
bsdgames
Combined size: 5.4 mb
7.10 End result
In total the installed packages plus kernel took up about 75mb of disk space of which 19.5mb was in the root
partition and 55.5 in /usr. On the Aero that left 39mb in /usr, 74mb on the T1910.
8.Appendix B: Resources relevant to this HOWTO
Linux Laptop HOWTO
http://www.snafu.de/~wehe/Laptop−HOWTO.html
Small Memory mini−HOWTO
http://eddie.cis.uoguelph.ca/~tburgess/
Linux on Laptops
http://www.cs.utexas.edu/users/kharker/linux−laptop/ HOWTOs and installation FAQs for a
wide range of machines.
Linux T1910 FAQ
http://members.tripod.com/~Cyberpvnk/linux.htm
Linux Contura Aero FAQ
7.8 Tetex
19
4mb−Laptops
http://domen.uninett.no/~hta/linux/aero−faq.html
Contura Aero FAQ
http://www.reed.edu/~pwilk/aero/aero.faq Comprehensive FAQ on all aspects of the Contura
Aero compiled by the moderators of the Aero mailing list. Good Linux section .
7.8 Tetex
20