CAL. V071, V072 ALARM CHRONOGRAPH

CAL. V071, V072
ALARM CHRONOGRAPH
● Digital time and calendar
● Daily alarm
● 60-minute stopwatch
● Illuminating light
ENGLISH
● Analogue time display
DISPLAY AND CROWN/BUTTONS
B
English
a
b
CROWN
Digital display
* The shape of the digital
display differs depending on the calibre.
A
C
PM
a: Normal position
b: Extended position
MODE CHANGE
A
With each press, the mode in the digital display changes in the
following order:
➡
CALENDAR
2
➡
TIME
➡
ALARM
➡
STOPWATCH
SCREW DOWN CROWN
[for models with screw down crown]
Unlocking the crown
1 Turn Crown counterclockwise until you no
longer feel the threads turning.
2 Crown can be pulled out.
1 Push Crown back in to normal position.
English
Locking the crown
2 Turn Crown clockwise while pressing it lightly
until tight.
3
TIME/CALENDAR SETTING
CALENDAR SETTING
A
▲
B
B
Press to show CALENDAR
mode.
Press for 2 to 3 seconds.
English
▲
▲
A
C
B
Select the digits to be adjusted.
▲
PM
C
Set the flashing digits.
▲
Month
Date
Day
A or B
Return to CALENDAR mode.
➾
Selection of the digits
Date ➾ Month ➾ Day of the week ➾ CALENDAR mode
4
(Press for 2 to 3 seconds.)
DIGITAL TIME SETTING
● Before setting the analogue time, be sure to set the digital time.
A
B
Press to show TIME mode.
▲
B
Press for 2 to 3 seconds.
▲
C
Select the digits to be adjusted.
▲
A
B
C
Set the flashing digits.
English
▲
PM
▲
Minutes
Seconds
A or B
Return to TIME mode.
Selection of the digits
Seconds ➾ Minutes ➾ Hour ➾ 12-/24-hour indication
➾
➾
Hour
(Press for 2 to 3 seconds.)
TIME mode
5
ANALOGUE TIME SETTING
● Before setting the analogue time, be sure to set the digital time. (See the previous
section)
Second hand
CROWN
Minute
hand
English
Hour
hand
➠
➠
PM
6
1 Pull out when the second hand is
at the 12 o’clock position.
2 Turn to set the hour and minute
hands.
3 Push back in to normal position
when the second digits count “00”
in the digital time display.
ALARM
ALARM TIME SETTING
A
B
Press to show ALARM mode.
▲
▲
Select the digits to be adjusted.
▲
C
Hour
Minutes
ALARM mode mark
A or B
Return to ALARM mode.
Selection of the digits
Hour ➾ Minutes ➾ ALARM mode
➾
C
A
Set the flashing digits.
▲
PM
English
B
7
ALARM ENGAGEMENT/DISENGAGEMENT
C
Alarm
mark
English
PM
* At the designated time, the alarm
rings for 20 seconds.
To stop it manually, press any of
the buttons.
C
Alarm engaged
TURNING ON/OFF OF HOURLY TIME SIGNAL
B
B &C
Hourly time
signal mark
PM
8
With each press in ALARM
mode, the alarm is engaged
and disengaged alternately.
C
Hourly time signal turned on
With each simultaneous press
in CALENDAR or TIME mode,
the hourly time signal is turned
on and off alternately.
STOPWATCH
● The stopwatch measures up to 60 minutes in 1/100 second increments.
Split /
Split release / Reset
B
Minutes
C
Seconds
Start / Stop / Restart
English
PM
1/100 seconds
Split time measurement
•••••••
SPLIT
RELEASE
C
STOP
▲
B
▲
B
SPLIT
▲
▲
C
START
B
RESET
9
Measurement of two competitors
English
C
2ND
COMPETITOR
FINISHES
B
RESET
ILLUMINATING LIGHT
C
PM
C
10
B
FINISH TIME
OF 2ND
COMPETITOR
▲
FINISH TIME
OF 1ST
COMPETITOR
▲
B
▲
▲
C
START
Press and hold in TIME or
CALENDAR mode.
* The light illuminates the digital
display for easy viewing in the
dark.
NOTES ON OPERATING THE WATCH
TIME/CALENDAR SETTING
English
[CALENDAR SETTING]
● The calendar automatically adjusts for odd and even months except February of leap
years.
● The flashing digits move quickly if button C is kept pressed.
● If the watch is left untouched with the digits flashing, it will automatically return to the
CALENDAR mode in 1 to 2 minutes.
[DIGITAL TIME SETTING]
● The flashing digits except the seconds and 12-/24-hour indication move quickly if button
C is kept pressed.
● In second setting, when the seconds count any number from “30” to “59” and button
C is pressed, one minute is added and the seconds are reset to “00”.
● When setting the hour digits in the 12-hour indication, check that AM/PM is properly set.
Only the “PM” mark is displayed. For the AM setting, there is no indication.
● If the watch is left untouched with the digits flashing, it will automatically return to the
TIME mode in 1 to 2 minutes.
[ANALOGUE TIME SETTING]
● When setting the minute hand, first advance it 4 to 5 minutes ahead of the desired time
and then turn it back to the exact minute.
11
● When the crown is pulled out or pushed in for time setting, the minute hand may move
slightly. However, this is not a malfunction.
English
ALARM
[ALARM TIME SETTING]
● When the time function is displayed in the 24-hour indication, the alarm will also be
displayed in the 24-hour indication.
● The flashing digits move quickly if button C is kept pressed.
● When setting the hour digits in the 12-hour indication, check that AM/PM is properly set.
Only the “PM” mark is displayed. For the AM setting, there is no indication.
● If the watch is left untouched with the digits flashing, it will automatically return to the
ALARM mode in 1 to 2 minutes.
● Alarm test: The alarm can be tested by keeping buttons B and C pressed in the
CALENDAR or TIME mode.
STOPWATCH
12
● With each press of button C, the light illuminates the digital display with a beep.
● After measuring 60 minutes, the stopwatch will start counting again from “00'00"oo”
as many times as necessary until it is stopped.
● Restart and stop of the stopwatch can be repeated by pressing button C.
● Measurement and release of split time can be repeated by pressing button B.
● When measuring a long period of time, press button A to return the STOPWATCH mode
to the CALENDAR or TIME mode after the stopwatch starts. This will prevent any
possible malfunction.
BATTERY CHANGE
3
Years
Battery life : Approx. 3 years
Battery
: SEIKO SR927W
English
● If the alarm is used more than once a day, the stopwatch more than once a day, and/
or the illuminating light for more than one second a day, the battery life may be less
than the specified period.
● As the battery is inserted at the factory to check the function and performance of
the watch, its actual life once in your possession may be less than the specified
period.
● When the battery expires, be sure to replace it as soon as possible to prevent any
malfunction.
● We recommend that you contact an AUTHORIZED PULSAR DEALER for battery
replacement.
● Necessary procedure after battery change
After the battery is replaced with a new one, or in case an abnormal display (broken
digits, etc.) appears in the digital display, follow the procedure below to reset the IC.
Press buttons A, B and C at the same time. All the segments of the
13
digital display will light up, a beep will sound twice and then “January
1st, Sunday” will be displayed in the digital display.
* Before using the watch, set the time/calendar and alarm.
English
WARNING
● Do not remove the battery from the watch.
● If it is necessary to take out the battery, keep it out of the reach of
children. If a child swallows it, consult a doctor immediately.
● Never short-circuit, tamper with or heat the battery, and never expose
it to fire. The battery may burst, become very hot or catch fire.
CAUTION
● The battery is not rechargeable. Never attempt to recharge it, as this
may cause battery leakage or damage to the battery.
14
TO PRESERVE THE QUALITY OF YOUR WATCH
WATER RESISTANCE
● Non-water resistant
• If the watch becomes wet, have it checked by an AUTHORIZED
PULSAR DEALER or SERVICE CENTER.
5 bar
WR
10/15/20
bar WR
• Before using in water, be sure the crown is pushed in completely.
• Do not operate the crown and buttons when the watch is wet or in
water. If used in sea water, rinse the watch in fresh water and dry it
completely.
• When taking a shower with the water resistant 5 bar watch, or
taking a bath with the water resistant 10, 15 or 20 bar watch, be
sure to observe the following:
* Do not operate the crown or push the buttons when the watch is
wet with soapy water or shampoo.
* If the watch is left in warm water, a slight time loss or gain may
be caused. This condition, however, will be corrected when the
watch returns to normal temperature.
English
● Water resistant 5/10/15/20 bar
15
* Pressure in bar is a test pressure and should not be considered as corresponding
to actual diving depth since swimming movement tends to increase the pressure
at a given depth. Care should also be taken on diving into water.
** We recommend that you wear a PULSAR Diver’s Watch for scuba diving.
TEMPERATURES
English
16
MAGNETISM
Your watch works with
The analogue unit of your
stable accuracy within a
watch will be adversely
temperature range of 5° C
affected by strong
-5°C
and 35° C (41° F and 95°
magnetism, though the
S
N
F).
digital unit will not be
Temperatures over 50° C (122° F) or affected. Keep the watch away from
below –5° C (+23° F) may cause a close contact with magnetic objects.
slight time loss or gain or battery
leakage or shorten the battery life.
CARE OF CASE AND BRACELET
However, the above conditions will
To prevent possible
be corrected when the watch returns
rusting of the case and
to normal temperature.
bracelet caused by dust,
moisture and perspiration,
wipe them periodically
with a soft dry cloth.
+50°C
SHOCKS & VIBRATION
PERIODIC CHECK
Be careful not to expose
the watch to solvents,
mercury, cosmetic spray,
detergents, adhesives or
paints. Otherwise, the
case, bracelet, etc. may become
discolored, deteriorated or damaged.
PRECAUTION REGARDING
CASE BACK PROTECTIVE FILM
English
Light activities will not
It is recommended that the
affect your watch, but be
watch be checked once
2-3
careful not to drop your Years
every 2 to 3 years. Have
watch or hit it against hard
your watch checked by an
surfaces, as this may
AUTHORIZED PULSAR
cause damage.
DEALER or SERVICE CENTER to
ensure that the case, crown, buttons,
gasket and crystal seal remain intact.
CHEMICALS
If your watch has a
protective film and/or a
sticker on the case back,
be sure to peel them off
before using your watch.
17
English
STATIC ELECTRICITY
18
The IC (Integrated
Circuit) used in your
watch will be affected
by static electricity
which may disturb the
display. Keep the watch away
from close contact with objects
such as TV screens which emit
strong static electricity.
LIQUID CRYSTAL PANEL
The normal life expectancy for
the liquid crystal panel of the
watch is approximately 5 years.
5 Years After that it may decrease in
contrast, becoming difficult to
read. Please contact your AUTHORIZED
PULSAR DEALER or SERVICE CENTER
if you wish to have a new panel fitted
(guaranteed one year).