Miele T 4809 Ci Operating instructions

Operating instructions
for condenser tumble dryer
T 4809 Ci
To avoid the risk of accidents
or damage to the appliance
it is essential to read these
instructions before it is installed
and used for the first time.
en - GB
M.-Nr. 06 984 111
Caring for the environment
Disposal of the packing
material
The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled.
Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation!
Rather than just throwing these
materials away, please ensure they are
offered for recycling.
Disposal of your old appliance
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly,
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of your
appliance with your household waste.
Please dispose of it at your local
community waste collection / recycling
centre or contact your Dealer for
advice. Ensure that it presents no
danger to children while being stored
for disposal.
2
Energy saving tips
To avoid unnecessarily long drying
times and high consumption of energy:
– Make sure that your laundry is
thoroughly spun before drying.
The higher the spin, the greater the
savings that can be made in energy
and time during drying.
– Load according to the optimum
amount of laundry recommended for
the programme being used (see
Programme chart).
Underloading is uneconomical.
Overloading gives a poorer quality of
drying and may cause unnecessary
creasing.
– Make sure the room in which the
dryer is located is well ventilated.
– Make sure the fluff filters are clean
before using the dryer.
– Check the condenser unit from time
to time and clean it when necessary.
Contents
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operating the tumble dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Notes on laundry care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Care symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Tips on drying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
How to dry correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Brief instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Extra options / Delay start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Low temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Delay start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Changing the programme sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Once a programme has started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
- changing the programme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
- cancelling the programme and then selecting a different programme . . . . . 20
- cancelling the programme and then removing the laundry . . . . . . . . . . . . . . 20
Altering Delay start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Adding or removing laundry after a programme has started . . . . . . . . . . . . . . . . 20
Time remaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Electronic system lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3
Contents
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Emptying the condensed water container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cleaning the fluff filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Cleaning them whilst dry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Cleaning them with water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Cleaning the tumble dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Cleaning the condenser unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Removing the condenser unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Checking the condenser unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Cleaning the condenser unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Replacing the condenser unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Check and fault messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Other problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Changing the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
After Sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Repairs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Future updates (PC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Appliance guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Front view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Building under a continous worktop / in a kitchen run . . . . . . . . . . . . . . . . . . . 37
Aligning the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Room in which the dryer is located . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Washer-dryer stack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Before moving the tumble dryer again (e.g. when moving house) . . . . . . . . . 38
Matching the fascia panel to the height of adjacent drawer fronts . . . . . . . . . . . . 39
Removing the spacer bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Fitting the front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Front panel dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Fitting the front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
4
Contents
Fitting a door front panel made by another manufacturer . . . . . . . . . . . . . . . . . . . 41
Preparing the front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Preparing the fixing points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Fitting a plinth facing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
External condensed water outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Arranging the drain hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
External drainage via a sink or gully . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Installation conditions requiring a non-return valve . . . . . . . . . . . . . . . . . . . . . 45
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Electrical connection U.K. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Consumption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Programmable functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Extending the range of the drying levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Altering the volume of the buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Memory function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Extending the cooling down time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Clean out airways indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Keypad tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Adjusting the dryer's electronics for very soft water . . . . . . . . . . . . . . . . . . . . . . . 57
5
Warning and Safety instructions
Correct application
~ This tumble dryer is for domestic
~ It is essential to read these
instructions.
This tumble dryer conforms to
current safety requirements.
Inappropriate use can, however,
lead to personal injury and damage
to property.
To avoid the risk of accidents and
damage to the tumble dryer, please
read these instructions carefully
before using it for the first time. They
contain important information on its
safety, installation, use and
maintenance.
Keep these instructions in a safe
place and ensure that new users are
familiar with the content. Pass them
on to any future owner.
use only and can only be used to dry
items which have been washed in a
water solution and which are marked on
the manufacturer's care label as being
suitable for tumble drying. "Dry
cleaning kits" for freshening up
garments in a tumble dryer are
increasingly available on the market. If
using, do so at your own risk, and
follow the instructions provided on the
packaging.
Any other applications may be
dangerous. Miele cannot be held liable
for damage resulting from incorrect or
improper use or operation.
~ This appliance is not intended for
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience or knowledge, unless they
are supervised whilst using it or have
been shown how to use it by a person
responsible for their safety.
Safety with children
~ Keep children away from the tumble
dryer at all times. It is not a toy! To
avoid the risk of injury do not allow
them to play on or near it or to play with
its controls. Supervise children whilst
you are using it.
~ Older children may only use it if its
operation has been clearly explained to
them, and they are able to use it safely,
recognising the dangers of incorrect
use.
6
Warning and Safety instructions
Technical safety
~ Before setting up the tumble dryer,
check it for any externally visible
damage.
Do not install or use a damaged tumble
dryer.
~ Before connecting the tumble dryer,
ensure that the connection data on the
data plate (voltage and connected
load) match the mains electricity
supply. If in any doubt, consult a
qualified electrician.
~ The electrical safety of this tumble
dryer can only be guaranteed when
continuity is complete between it and
an effective earthing system which
complies with current local and national
safety regulations. It is most important
that this basic safety requirement is
present and regularly tested, and
where there is any doubt the household
wiring system should be inspected by a
qualified electrician. Miele cannot be
held liable for the consequences of an
inadequate earthing system (e.g.
electric shock).
~ Do not connect the tumble dryer to
the mains electricity supply by an
extension lead. Extension leads do not
guarantee the required safety of the
tumble dryer (e.g. danger of
overheating).
~ Unauthorised repairs could result in
unforeseen dangers for the user, for
which Miele cannot accept liability.
Repairs should only be undertaken by a
Miele approved service technician.
Ensure current is not supplied to the
tumble dryer until after maintenance or
repair work has been carried out.
~ Faulty components must only be
replaced by genuine Miele original
spare parts. Only when these parts are
fitted can the safety standards of the
tumble dryer be guaranteed.
~ If the connection cable is faulty it
must only be replaced by a Miele
approved service technician to protect
the user from danger.
~ In the event of a fault or for cleaning
purposes, the tumble dryer is only
completely isolated from the electricity
supply when:
– it is switched off at the wall socket
and the plug is withdrawn, or
– it is switched off at the mains, or
– the mains fuse is disconnected, or
– the screw-out fuse is removed (in
countries where this is applicable).
~ This tumble dryer may only be used
in mobile installations such as ships if a
risk assessment of the installation has
been carried out by a suitably qualified
engineer.
~ In countries where there are areas
which may be subject to infestation by
cockroaches or other vermin, pay
particular attention to keeping the
tumble dryer and its surroundings in a
clean condition at all times. Any
damage which may be caused by
cockroaches or other vermin will not be
covered by the guarantee.
~ Do not make any alterations to the
tumble dryer, unless authorised to do
so by Miele.
7
Warning and Safety instructions
Correct use
~ To prevent the risk of fire, the
following textiles must not be dried in
this tumble dryer:
– items which have not been washed.
– items, such as workwear, which have
not been thoroughly cleaned and
which are still soiled with grease, oil
or other deposits (such as
cosmetics, lotions etc).
If items have not been thoroughly
cleaned there is a danger that these
might ignite when heated, even after
they have been removed from the
dryer at the end of the programme.
– items (e.g. mops and floorheads)
which have been treated with
inflammable cleaning agents or
contain residues of acetone, alcohol,
benzine, petrol, stain remover,
turpentine, wax, wax remover or
other chemicals.
– items which have been splashed with
hair lacquer, hair spray, nail varnish
remover or similar substances.
When washing such heavily soiled
items ensure that you use sufficient
detergent and select a high
temperature. If in doubt, wash the
items several times.
~ To prevent the risk of fire, the
following must not be dried in this
tumble dryer:
– items which have been cleaned
using chemicals (e.g. professional
dry-cleaning agents).
– fabrics which contain a large
proportion of rubber, foam rubber or
rubber-like materials. For example,
products made from latex foam
rubber, shower caps, waterproof
textiles, rubberised articles and items
of clothing and pillows with foam
rubber filling.
– damaged items which contain
padding or fillings (e.g. pillows,
jackets). When damaged, the filling
can get out with the risk of igniting in
the dryer.
~ In many programmes, the heating
phase is followed by a cooling down
phase to ensure that the items are not
too hot to handle when you remove
them (this also avoids the danger of the
laundry self-igniting). The programme is
not finished until the cooling down
phase has been completed.
Ensure that you always wait until the
end of the programme before removing
the laundry.
~ Warning: Do not switch the tumble
dryer off before the end of the drying
programme. If this was done and the
laundry was then removed immediately
it could give off a great amount of heat.
~ Fabric conditioner and similar
products must be used according to
the instructions on the manufacturer's
packaging.
8
Warning and Safety instructions
~ The dryer must not be used without
the fluff filters in place or if the fluff
filters are damaged in any way.
~ The fluff filters must be cleaned
regularly.
~ Always keep the area around the
tumble dryer free of dust and fluff. Dust
drawn into the tumble dryer can cause
blockages in the condenser unit over
time.
~ The dryer must not be used without
~ Do not let anyone sit or lean on the
~ The fluff filters must be thoroughly
dried after cleaning. Damp or wet filters
could cause operational faults.
~ Always close the door after use. This
~ Do not install the tumble dryer in a
– children climbing onto or into the
dryer or hiding things in it.
the condenser unit in place.
room where there is a risk of frost
occurring. At temperatures around
freezing point the tumble dryer may not
be able to operate properly.
There is a risk of damage if the
condensed water is allowed to freeze in
the pump, hoses and / or condensed
water container.
The ambient room temperature should
be between +2°C and +35°C.
~ If the water is drained externally
through the drain hose instead of being
collected in the condensed water
container, make sure the drain hose is
securely attached if you hang it in a
sink or basin to avoid the hose slipping
and the water causing damage.
~ Condensed water is not drinking
water.
It can cause health problems in both
people and animals.
door, as this can cause the tumble
dryer to tip up.
way you will avoid the danger of:
– pets or other small animals climbing
into it.
~ The tumble dryer must not be hosed
down.
Accessories
~ Only use genuine Miele spare parts
and accessories with this appliance.
If non-Miele parts are used, guarantee,
performance and product liability
claims may be invalidated.
Miele cannot be held liable for
damage caused by non-compliance
with these Warning and Safety
instructions.
9
Operating the tumble dryer
Control panel
a Low temperature button
Delicate fabrics are dried at a lower
temperature.
b Drying level button
with indicator lights
c Display
d Delay start button
This button is used for:
- Selecting the duration of the
Timed drying programmes
- Delaying the start of a programme
e Buzzer button
An audible tone sounds at the end of
the programme.
f Check lights
For a description of these lights see:
"Problem solving guide" / "After sales
service".
g Start/Stop button
For starting the programme selected
and cancelling a programme once it
has started.
The indicator light flashes while a
programme is being selected and
then is on constantly when the
programme has started.
h Programme selector
with indicator lights
i Door button
Pressing this button will open the
door even when the dryer is
switched off.
j On/Off button
For switching the dryer on and off.
10
Operating the tumble dryer
Display
The following are selected via the
display:
– Delay start
– Duration of the Cool air and Warm air
programmes
In the same way, the Woollens
handcare, Silks handcare and
Smoothing programmes can finish
earlier than expected if a certain
temperature is reached. This can
happen with particularly fine fabrics,
very small loads or if items were partly
dry beforehand.
– Programmable functions
The display also shows:
Delay start
– Programme duration
The delay start time selected will
appear in the display.
– Programme stage
Drying
Cooling down
Finish
After the Start/Stop button has been
pressed, the delay start time will start
counting down.
– Check and fault messages
Programme duration / Estimated time
remaining
When a programme is selected, the
estimated duration (time remaining) will
appear in the display. Please be aware
that it is only an estimate!
The following factors all affect the
estimated time remaining: residual
moisture content after spinning; type of
fabric; size of load; room temperature;
fluctuations in power supply.
Once the delay start time has elapsed,
the programme will begin and the
estimated programme duration will
appear in the display.
Programmable functions
The programmable functions can be
used to tailor drying programmes to suit
your individual requirements. In
programming mode, the display will
show the function selected.
The electronics continually assess
conditions in the dryer and adjust the
estimated time remaining for a more
accurate reading. Because of this, the
time displayed can alter during the
course of a programme.
11
Notes on laundry care
Care symbols
Before drying check the drying symbol
on the care label. If there are no
symbols, dry at your own risk!
q . . . . . . . . . Dry at normal temperature
r. . . . . . . . . . . . Dry at low temperature
s . . . . . . . . . . . . . . . Do not tumble dry
Tips on drying
– Always observe the maximum
recommended loads given in the
"Programme chart". Never overload
the drum.
Overloading can cause unnecessary
wear and tear to the laundry, give a
disappointing drying result and
cause more creasing.
– Do not put soaking wet items into the
tumble dryer. Spin them thoroughly
after washing using the appropriate
spin speed.
– For delicates and fabrics with the
following care label r select Low
temperature.
– Use the Automatic programme for
drying mixed loads of cottons and
minimum iron fabrics.
– Open jackets so that they can dry
evenly.
– Woollens and wool blends tend to
become matted and shrink if dried in
a tumble dryer. They can, however,
be partially dried using the Woollens
handcare programme.
12
– Down-filled garments have linings
which have a tendency to shrink,
depending on the quality of the item.
They can be partially dried using the
Smoothing programme.
– Pure linen should only be machine
dried if specified as suitable by the
manufacturer on the care label, as
the surface of the fabric may
otherwise become rough. They can
be partially dried using the
Smoothing programme.
– Loopknit garments (e.g. T-shirts and
underwear) tend to shrink depending
on their quality. Do not over-dry
these textiles. When purchasing
these garments it is advisable to take
their shrinkage properties into
account.
– For garments made from very fine
weave fibres, such as shirts or
blouses, only use the Shirts or
Delicates programme to avoid
creasing. If in doubt, reduce the load
or use the Smoothing programme.
– Starched laundry can be dried in the
tumble dryer. To achieve the usual
finish, double the amount of starch
should be used.
– New dark coloured garments should
be washed and dried separately
from light coloured garments to avoid
the danger of colours running and
discolouring other garments or even
plastic components in the appliance.
Dark coloured fibres can also settle
on light coloured garments and vice
versa.
How to dry correctly
Brief instructions
C Load the tumble dryer
The headings numbered (A, B, C ...)
show the operating sequence and can
be used as a brief guide to using your
dryer.
^ Press the Door button to open the
door.
^ Load the laundry loosely into the
drum.
A Sort the laundry
To ensure an even drying result
separate the washed laundry and sort it
according to:
. . . the drying level required
. . . the type of fibre or weave
. . . size
. . . the moisture content after spinning.
,Make sure that objects e.g.
detergent dispensing balls have
been removed from the laundry.
They could melt, and cause damage
to the dryer or the laundry.
Do not overload the drum. See the
"Programme chart" for
recommended loads for each
programme.
Overloading can cause unnecessary
wear and tear to the laundry and
give a disappointing drying result.
^ Before closing the door make sure
the fluff filter is correctly positioned.
– Check seams and stitching to ensure
that padding and linings are intact.
– Fasten duvet covers and pillow
cases to prevent small items from
being trapped inside them.
– Fasten hooks and eyes etc.
– Tie fabric belts and apron strings.
– Sew in or remove underwiring from
bras.
B Turn on the tumble dryer
^ Switch the dryer on by pressing the
On/Off button in.
The tumble dryer may be switched on
after loading, saving energy as the light
will not come on.
Check the laundry is right inside the
drum so that it cannot get trapped or
damaged when the door is shut.
^ Shut the door either with a gentle
swing, or lean against it and push it
shut.
13
How to dry correctly
D Select a programme
Important: Please note that the
programme duration shown in the
display will vary according to the
programme selected (see "Programme
duration/Estimated time remaining").
The Woollens handcare, Silks handcare
and the Smoothing programmes cannot
be changed.
Timed drying programmes
The indicator light for the Delay start
button will flash when the Cool air or
Warm air programme is selected.
^ Select the programme you want.
The indicator light for the programme
selected will light up.
A drying level or extra option indicator
light may also light up, and the duration
may also be displayed.
Cottons, Minimum iron, Delicates,
Automatic, Shirts, Denim and
Outerwear programmes
^ Press the Delay start button
repeatedly until the required duration
shows in the display.
You can select a duration of 20 minutes
up to 2:00 hours in 10 minute steps.
E Select any Extra options / Delay
start
^ Low temperature, buzzer and delay
start are selected by pressing the
appropriate button (see "Extra
options / Delay start").
Anti-crease (see next page) is
permanently switched on.
N.B.: It is not possible to select Delay
start when using the Warm air or Cool
air programme.
^ Press the Drying level button
repeatedly until the indicator light for
the drying level you want lights up.
Any of the drying levels can be
selected for the Cottons programme. A
more limited range is available when
using other programmes.
14
How to dry correctly
F Start the programme
The Start/Stop button will flash when a
programme is being selected. The
flashing indicates that a programme
can be started.
^ Press the Start/Stop button.
The Start/Stop button will now light up
constantly.
Drying will appear in the display and
the time remaining will start counting
down.
Before the end of a programme
There is a cooling down phase at the
end of the drying sequence (Cooling
down will appear in the display). The
programme will not finish until the
cooling down phase has been
completed.
There is no cooling down phase at the
end of the Woollens handcare, Silks
handcare and Smoothing programmes.
G Remove the laundry when the
programme has finished
0 and Finish will appear in the display
to indicate that the programme has
finished. The buzzer (if selected) will
sound at intervals.
The drum will continue to rotate at
intervals for up to an hour to prevent
laundry creasing, if you do not wish to
remove it immediately (anti-crease).
There is no anti-crease phase at the
end of the Woollens handcare or Silks
handcare programmes.
^ Press the Door button.
^ Open the door.
^ Remove the laundry.
Check that all items have been
removed from the drum. If items are
left in the dryer, they could be
damaged by overdrying when the
dryer is next used.
If the dryer is switched on at the mains
and the door is opened, the drum
lighting will come on. It will go out a few
minutes later to save energy.
^ Switch the dryer off by pressing the
On/Off button.
^ Clean the fluff filters.
^ Close the door.
^ Empty the condensed water
container (unless the dryer has been
connected for external drainage).
^ The condenser unit should be
checked at regular intervals and
cleaned if necessary (see "Cleaning
and care").
15
Extra options / Delay start
Low temperature
For all delicate or minimum iron
fabrics with the r symbol on the
care label (e.g. acrylic garments).
– The programme duration is longer.
– On some programmes Low
temperature is a standard part of the
programme and so cannot be
deselected.
Buzzer
A buzzer sounds (at intervals for a
maximum of 1 hr) to let you know the
programme has finished.
– If you keep the Delay start button
pressed in, the time will continue to
increase up to 24^.
To begin delay start
^ Press the Start/Stop button.
– The Delay start indicator light will
light up constantly.
The delay start time counts down
towards the start of the programme as
follows:
– more than 10^ by the hour
– less than 10^ in minutes
The drum will turn briefly every hour to
help prevent creasing.
The buzzer will still sound if there is a
fault, even if it has been switched off.
While the delay start time is counting
down, you can still add laundry to the
drum:
Delay start
^ Switch the dryer off.
The start of a programme can be
delayed by 30 minutes up to 24
hours to allow you to take advantage
of economy electricity at night, for
example.
After selecting a programme:
^ Press the Delay start button
repeatedly until the required delay
period shows in the display.
– The Delay start indicator light will
flash.
– Times of:
up to 10^ are selected in 30 minute
steps
more than 10^ in 1 hour steps
16
^ Open the door and add the laundry.
^ Close the door and switch the dryer
back on again.
To cancel/alter delay start
^ Press the Start/Stop button.
This cancels delay start.
^ To alter the delay start time, press the
Delay start button repeatedly until the
required delay period shows in the
display.
^ Press the Start/Stop button.
The altered delay start time will start
counting down from the beginning
again.
Programme chart
Cottons
Max. load 6 kg*
Extra dry, Normal**
Fabric type
Single and multi-layered cotton fabrics such as towelling,
jerseywear, T-shirts, underwear.
Notes
– Select Extra dry for multi-layered and very thick fabrics.
– Do not use Extra dry for loopknit fabrics (e.g. T-shirts,
underwear), as they have a tendency to shrink.
Low temperature
Select the Low temperature option for delicate fabrics with
the r symbol on the care label.
Hand iron**, Machine iron
Fabric type
Cottons or linen fabrics, e.g.: table linen, bed linen, starched
laundry.
Note
– To prevent laundry from drying out it should be rolled up
until you are ready for ironing.
Low temperature
Select the Low temperature option for delicate fabrics with
the r symbol on the care label.
Minimum iron
Max. load 3 kg*
Extra dry, Normal**, Hand iron
Fabric type
Minimum iron items made of cotton, synthetic or blended
fabrics, e.g.: shirts, blouses, skirts and table cloths.
Notes
– Select Hand iron for delicate fabrics and to reduce
creasing even more, reduce the load to 1.5 kg*.
– In the Minimum iron programme with the Hand iron drying
level, items are dried with very little creasing, depending
on fabric type and amount of laundry.
Low temperature
Select the Low temperature option for delicate fabrics with
the r symbol on the care label.
Delicates
Max. load 2 kg*
Normal, Hand iron
Fabric type
Delicate items made of synthetic fibres, easy care cotton or
blended fabrics, e.g. shirts, blouses, lingerie and appliquéd
garments.
Low temperature
Low temperature cannot be deselected.
* Weight of dry laundry
** Note for test institutes: Use this programme without selecting Low temperature
for testing according to EN 61121 Standard.
17
Programme chart
Woollens handcare
Max. load: 2 kg*
Fabric type
Woollen fabrics
Note
– This programme only fluffs up woollen garments.
– Fabrics are not completely dried in this programme.
Remove garments as soon as the programme has finished
and leave to finish drying at room temperature.
Low temperature
Low temperature cannot be deselected.
Silks handcare
Max. load: 1 kg*
Fabric type
Silks, e.g. blouses and shirts.
Notes
– Smooths out creasing.
– Fabrics are not completely dried in this programme.
Remove garments as soon as the programme has finished
and leave to finish drying at room temperature.
Low temperature
Low temperature cannot be deselected.
Smoothing
Max. load: 3 kg*
Fabric type
– Cotton and linen fabrics.
– Minimum iron mixed fibre, cotton or synthetic items, e.g.:
trousers, jackets, shirts.
Notes
– Smooths out creasing caused during the spin cycle in the
washing machine.
– Fabrics are not completely dried in this programme.
Remove garments as soon as the programme has finished
and leave to finish drying at room temperature.
Low temperature Low temperature cannot be deselected.
* Weight of dry laundry
18
Programme chart
Automatic
Max. load: 3.5 kg*
Normal, Hand iron
Fabric type
Mixed loads of garments suitable for the Cottons and
Minimum iron programmes. Sort according to colour.
Shirts
Max. load: 2 kg*
Normal, Hand iron
Fabric type
Shirts and blouses.
Low temperature Select the Low temperature option for delicate fabrics with the
r symbol on the care label.
Denim
Max. load: 3 kg*
Normal, Hand iron
Fabric type
Denim garments, e.g. jeans, jackets, skirts, shirts.
Low temperature Select the Low temperature option for delicate fabrics with the
r symbol on the care label.
Outerwear
Max. load: 2 kg*
Normal, Hand iron
Fabric type
Outerwear which is suitable for drying in a tumble dryer.
Low temperature Low temperature cannot be deselected.
Cool air
Max. load: 6 kg*
Fabric type
Any item which only needs airing.
Warm air
Max. load: 6 kg*
– Multi-layered fabrics whose layers have different drying
Fabric type
characteristics, e.g. jackets, pillows.
– For drying individual items, e.g. bath towels, bathing
costumes, tea-towels and small loads.
– Do not select the longest drying time to start with. Check
Note
the items as you are drying them to find the optimum time.
Tip
You can use the Warm air programme to help remove odours
from cotton clothing which has been worn but it still clean (select
a duration of between 1/2 and 1 hour). Items must be suitable
for drying in a tumble dryer. Dampen the garments a little
beforehand or add a fabric conditioner sheet. The Warm air
programme will not be as effective at removing odours from any
parts of the garments which are made of synthetic fibres.
Low temperature Select the Low temperature option for delicate fabrics with the
r symbol on the care label.
* Weight of dry laundry
19
Changing the programme sequence
Once a programme has started
Altering Delay start
- changing the programme
^ See "Delay start".
You cannot change to another
programme once a programme has
started (this prevents unintentional
alterations).
You will need to cancel the current
programme before you can select a
new one.
- cancelling the programme and then
selecting a different programme
^ Press the Start/Stop button.
The items will be cooled down,
depending on the temperature
reached and how long they have
been dried for.
If you press the Start/Stop button
again during the cooling down
phase, Finish will light up in the
display.
^ Press the Door button.
^ Close the door.
^ Select another programme and start
it.
- cancelling the programme and then
removing the laundry
^ Proceed as described in "Adding or
removing laundry after a programme
has started" below.
^ Switch the dryer off after closing the
door.
20
Adding or removing laundry
after a programme has started
^ Press the Door button.
^ Open the door.
,Danger of burning:
Do not touch the back of the drum
when adding or removing items. The
drum and the items can get very hot.
^ Add or remove items as required.
^ Close the door.
^ Press the Start/Stop button.
Time remaining
The time left shown in the display may
now vary from the actual drying time.
Electronic system lock
The system lock prevents the dryer
being used without your knowledge.
It can be activated if wished.
The dryer's electronics are then locked.
The dryer can still be switched on but a
programme cannot be started.
– If an attempt is made to start a
programme, the indicator light for the
Low temperature button will come on
and a key symbol 0-§ will appear in
the display.
The door is not locked and can be
opened at any time.
To activate the lock
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
A Press the Low temperature button
and keep it pressed in whilst carrying
out steps B to E.
B Press the jk button in.
The Automatic indicator light will come
on.
D Now slowly turn the programme
selector six positions stage by stage
in an anti-clockwise direction.
Each of the six programme indicator
lights must come on one after the
other.
The indicator light for the Low
temperature button will flash and a key
symbol 0-§ will appear in the display.
E Release the Low temperature button.
The electronics have now been locked.
^ Switch the dryer off.
To deactivate the lock
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
^ The procedure is the same as for
activating the lock. Carry out steps A
to E as described previously.
At step E the indicator light for the Low
temperature button will stop flashing
and the key symbol 0-§ will go out.
The electronics are no longer locked.
C Slowly turn the programme selector
three positions stage by stage in a
clockwise direction.
Each of the three programme
indicator lights must come on one
after the other.
21
Cleaning and care
Emptying the condensed
water container
The condensed water will be collected
in the condensed water container
unless the appliance has been fitted
with a drain hose (see "Installation").
Empty the condensed water
container after every drying
programme.
The Empty out container indicator light
will come on if the maximum level of the
condensed water container is reached.
The indicator light will go out when the
door is opened and closed again.
^ Open the shutter and empty out the
water.
^ To replace the container, hold it at a
slight angle (as when removing it)
and push it in gently until you feel it
click into position.
,Condensed water should not be
consumed. It could lead to health
problems for people and animals.
Condensed water can be put to
household use (e.g. in a steam iron or
humidifier). To ensure that any residual
particles of fluff in the condensed water
are removed before use, pass it
through a fine sieve or paper filter first.
^ Holding the container firmly in both
hands, as shown, pull it out slightly
towards the right-hand side.
^ Hold the container with both hands
and carry it in a horizontal position.
22
Cleaning and care
Cleaning the fluff filters
The fluff which is created by the drying
process is collected by the fluff filters in
the door and the door opening. Clean
the filters after each drying
programme*.
Cleaning them whilst dry
Tip: You can also use a vacuum
cleaner to remove the fluff.
^ Remove any fluff from the hollow part
of the door opening. You could also
use a cleaning brush which is
available as an optional extra from
your Miele dealer or the Miele Spare
Parts Department, or use a vacuum
cleaner.
^ Also clean the door seal (2) with a
damp cloth.
^ Once clean, push the filter back into
the door holder until it clicks into
position. Ensure it is facing the
correct way.
^ Open the door and pull the fluff filter
(1) out of the door as illustrated.
^ Use your fingers or a vacuum cleaner
to remove the fluff from the two fluff
filters in the door opening.
^ Close the door.
* Always check the fluff filters if the
Clean out airways indicator light
comes on.
^ Use your fingers to remove the fluff
from the surface of the filter.
23
Cleaning and care
Cleaning them with water
If there is a great deal of compacted
fluff on any of the filters, they can be
removed and cleaned under hot
running water.
^ Open the door and pull the fluff filter
out of the door as described
previously.
The two filters in the door opening can
also be removed if you need to clean
them with water.
^ Turn dial a and pull the filter by the
dial out of the door opening as shown
b. Do the same on the other side.
^ Rinse all the filters under hot, running
water.
^ Then shake the filters until no more
water droplets are visible.
^ Dry the filters thoroughly with care.
^ Clean the area underneath these
filters, e.g. with a vacuum cleaner.
24
,Do not replace them if they are
damp or wet. Damp or wet filters
could cause operational faults.
^ Push the large filter back into the
door holder until it clicks into position.
Ensure it is facing the correct way.
^ Replace the filters in the door
opening by first inserting them at the
bottom and then pressing them into
place at the top.
^ Lock both dials.
Cleaning and care
Cleaning the tumble dryer
Disconnect the tumble dryer from
the mains electricity supply.
Miele branded cleaning and
conditioning products are available to
order via the internet on
www.miele-shop.com.
^ Clean the housing and control panel
with a slightly damp cloth and a mild
detergent or soapy water.
^ The drum and other stainless steel
parts can be cleaned with a suitable
stainless steel cleaner following the
manufacturer's instructions.
Do not use solvents, abrasive
cleaners, glass cleaners or
all-purpose cleaners. These could
damage plastic sufaces and other
parts. The tumble dryer must never
be hosed down.
^ Dry all parts with a soft cloth.
25
Cleaning and care
Cleaning the condenser unit
Detergent residue, hair and fine fluff
from the dryer can get through the fluff
filters and block the condenser unit.
Dust from the room in which the dryer is
installed can also get into the
condenser unit and cause a blockage.
Check the condenser unit at least
once a year. Always check it if the
Clean out airways indicator light
comes on. Clean it if necessary.
Removing the condenser unit
^ Turn the lever on the inner cover
downwards to the vertical position.
^ Open the service panel. Hold the
panel securely when doing this.
^ Tilt the cover forwards.
^ Now remove the panel by pulling it
diagonally upwards and place it to
one side.
26
^ Remove it by pulling it diagonally
upwards.
^ Turn the lever on the condenser unit
upwards to the vertical position so
that the hook on the lever is no longer
in the groove at the bottom of the
condenser unit housing.
Cleaning and care
If you cannot see any fluff:
^ Replace the condenser unit (see
following page).
If you can see some fluff:
^ Clean the condenser unit as
described below.
Cleaning the condenser unit
^ When rinsing the condenser unit,
make sure you position it as
shown in the next two illustrations.
^ Pull the condenser unit out of its
housing by the handle.
Checking the condenser unit
^ Hold the condenser unit up to the
light as shown.
^ Use a shower head or similar to rinse
the unit out as shown.
^ Check to see if there is any fluff
inside it.
The arrows in the illustration above
indicate where to look.
27
Cleaning and care
Replacing the condenser unit
^ With the handle facing upwards,
push the condenser unit back into
position in its housing.
^ Turn the lever down to the horizontal
position, making sure that the hook
on the lever clicks into the groove.
When replacing the inner cover after
cleaning, ensure that the rubber seal
fits correctly into the groove.
^ Then flush the unit through from the
front.
^ Check the condenser unit again for
any visible fluff and if necessary flush
it through again until it has all gone.
^ Replace the inner cover making sure
the hooks locate correctly. Hold it at
an angle and push it gently
downwards.
^ Then turn the lever upwards into the
horizontal position to lock the cover.
^ Also make sure the rubber seals are
clean.
The rubber seals must not be
removed and must be free of kinks.
^ Replace the service panel and press
the upper edge until it clicks into
position.
Checking and cleaning the condenser
unit housing
the condenser unit and the cover
are correctly positioned and locked,
otherwise water may leak from the
dryer.
^ Remove any soiling still visible inside
the housing unit by hand using a
damp cloth. Do not try and access
areas you cannot reach by hand!
28
,It is important to ensure that both
Problem solving guide
With the help of the following notes, minor faults in the performance of the
appliance, some of which may result from incorrect operation, can be put right
without contacting the Service Department.
,Repair work to electrical appliances should only be carried out by a
suitably qualified person in strict accordance with current local and national
safety regulations. Repairs and other work by unqualified persons could be
dangerous. The manufacturer cannot be held liable for unauthorised work.
Check and fault messages
Problem
The programme stops
and 0 and Finish appear
in the display.
The buzzer sounds.
Possible cause
This is not a fault.
The electronic unit has
recognised that there is
no laundry in the drum
and cancelled the
programme.
Drying individual
garments or items which
are already dry can also
cause the programme to
be cancelled.
The Low temperature
indicator light starts
flashing after the dryer
has been switched on
and 0-§ appears in the
display.
The programme stops
and Cooling down or
Finish flashes in the
display.
The buzzer sounds.
The electronic system
lock is activated.
No obvious cause.
Remedy
– Use the Warm air
programme (timed
drying) to dry individual
items.
– To select a new
programme, switch the
dryer off and on, or
– Open the door, place
more laundry in the
drum, then close the
door.
You will need to
deactivate the system
lock before the dryer can
be used (see "Electronic
system lock").
– Switch the dryer off
and then on again.
– Then start the
programme again.
If the programme stops
again and Cooling down
or Finish flashes again,
there is a fault. Contact
the Miele Service
Department.
29
Problem solving guide
Problem
Possible cause
– Cleaning the fluff filters is
usually all that is required.
However, if the Clean out
airways indicator light does
not go out after you have
cleaned the filters, then also
check all the possible causes
described under "The drying
process goes on too long or
even switches off".
To switch off the indicator
light:
– With the dryer switched on,
open and close the door.
The Clean out airways indicator
light can be deactivated (see
"Programmable functions").
See above for possible To switch off the indicator
The programme
stops.
causes and their
light:
remedies.
– With the dryer switched on,
The Clean out
airways indicator
open and close the door.
light comes on.
– Then start the programme
The buzzer sounds.
again.
– If the Clean out airways
indicator light comes on
again, contact the Miele Service Dept.
– Empty out the condensed
The Empty
The condensed water
container indicator container is full or there
water container.
light comes on.
is kink in the drain hose. – Check the drain hose.
The buzzer sounds.
To switch off the indicator
light:
– With the dryer switched on,
open and close the door.
The Clean out
airways indicator
light comes on.
30
This indicator light
comes on to warn you
that the dryer is not
working efficiently.
Possible cause: the fluff
filters are clogged with
fluff or with detergent
residues.
Remedy
Problem solving guide
Other problems
Problem
The drying
process goes
on too long or
even switches
off.
In some
circumstances,
the Clean out
airways
indicator light
still comes on,
even though
the filters are
clean.
Possible cause
Remedy
Please check all the possible causes and switch the dryer
off and then back on again.
Ventilation to and from the dryer
may be insufficient (e.g.
because it is installed in a small
room). This has caused the
temperature in the room to rise
sharply.
The fluff filters are clogged up
with fluff or were still wet when
they were replaced.
Open a door or window while
the tumble dryer is in
operation for increased air
flow.
– Remove any fluff.
– The fluff filters must be
completely dry.
The laundry has not been spun Make sure that your laundry is
sufficiently.
thoroughly spun at the
appropriate spin speed.
The tumble dryer has been
overloaded.
Do not exceed the maximum
load for the programme
selected.
Metallic components, e.g. zips – Open zips next time.
have prevented the dryer from If the problem occurs again,
registering the correct moisture dry garments with long zips
level in the laundry.
using the Warm air
programme (timed drying).
Detergent residues, hair and
Check the condenser unit
fine fibres can block up the
from time to time and clean it
condenser unit.
if necessary.
The vents below the door are
blocked.
The laundry is The load consisted of different
not sufficiently fabrics.
dry.
Remove any objects that are
blocking the vents.
– Finish drying using the
Warm air programme.
– Select a different
programme next time.
31
Problem solving guide
Problem
Possible cause
Remedy
– The inner cover of the – Ensure that the
condenser unit has not
condenser unit is
been locked properly
positioned correctly
and/or the condenser
and lock the inner
unit has not been
cover.
positioned correctly.
– Check the rubber
seals.
– Fluff has collected in
the condenser unit
– Use a cloth to remove
housing.
any visible fluff from the
inside of the condenser
unit housing.
Items made of synthetic Synthetic fibres tend to
Static charge can be
fibres are charged with attract static charge.
reduced by adding a
static electricity after
fabric conditioner to the
drying.
final rinse in the washing
programme or a fabric
conditioner sheet to the
load when drying.
Water leaks from the
dryer after the
condenser unit has
been cleaned.
There is a build-up of
fluff.
32
Fluff is principally the
result of friction when
garments are being worn
and washed. Machine
drying does not affect the
lifetime of fabric.
Fluff is collected by the
fluff filters and can be
easily removed (see
"Cleaning and Care").
Problem solving guide
Problem
Possible cause
The tumble dryer fails to No obvious cause.
start when switched on.
Power cut.
The interior drum
lighting does not come
on.
Remedy
– Is the dryer switched
on?
– Is the plug correctly
inserted into the socket
and switched on?
– Is the door closed
properly?
– Has the fuse or circuit
breaker tripped?
A programme which was running previously will
continue automatically when power is restored to the
tumble dryer as long as the Cooling down phase had
not been reached.
The lighting switches off Switch the dryer off and
automatically (to save
then on again.
energy).
The lamp needs
changing.
Change the lamp as
described at the end of
this section.
33
Problem solving guide
Changing the lamp
Disconnect the tumble dryer from
the mains electricity supply.
The lamp specification and
maximum wattage is stated on the
data plate and on the lamp cover.
^ Open the door.
^ Replace the lamp.
You will find the interior lamp cover at
the top of the drum aperture.
^ To close the cover push it upwards
and press it on the left and right until
you hear it click into position.
,Ensure that it is fitted into
position securely, as any moisture
could cause a short circuit.
^ Insert a suitable tool, such as a wide
bladed screwdriver, under the side
edge of the lamp cover as illustrated.
^ Apply a little pressure and whilst
doing so turn your wrist in the
direction of the arrow to open the
cover.
The cover will open downwards.
The temperature resistant lamp should
only be ordered from your Miele Dealer
or the Miele Spare Parts Department.
34
After Sales service
Repairs
Future updates (PC)
In the event of any faults which you
cannot remedy yourself, please contact
The indicator or check light marked PC
on the fascia panel is the interface used
by the Miele service technicians during
service work for testing purposes and
for updating the appliance's
programme data.
– your Miele dealer or
– the Miele Service Department (see
back cover for contact details).
When contacting your dealer or the
Service Department, please quote the
model and serial number of your
appliance, both of which are shown on
the data plate situated on the right
hand side below the drum aperture.
Appliance guarantee
Please see the guarantee card
supplied with your appliance.
Optional accessories
Optional accessories for this dryer are
available from your Miele Dealer, the
Miele Spare Parts Department or via the
internet at www.miele-shop.com.
Please note that telephone calls may
be monitored and recorded for
training purposes.
N.B. A call-out charge will be
applied for service visits where the
problem could have been resolved
as described in these instructions.
35
Installation
Front view
a Mains connection cable
f Four height adjustable screw feet
b Condensed water container
g External drainage options (e.g. via
wash basin, wash basin drain outlet
or gully)
c Control panel
d Door (can be fitted with a decor
panel)
e Service panel for condenser unit
36
Installation
Installation site
,Make sure the dryer door can be
opened without hindrance after
installation.
Building under a continous worktop /
in a kitchen run
This tumble dryer is specially designed
for installation under a continuous
worktop run in a fitted kitchen.
– The slides (available to order) should
be used to protect the floor from
damage when the dryer is pushed
into position or taken out for
servicing.
– The electrical socket must be
located in an accessible position
near the machine.
Please note:
N = Niche height (820-930 mm)
It is supplied fitted with a cover plate
instead of an appliance lid. The
cover plate is necessary to ensure
electrical safety and must not be
removed.
Niche height
Accessory
820 mm
None required
from 830-840 mm Fit longer screw feet* (set to
approx. 40 mm)
from 870-885 mm Use one raising kit*
from 915-930 mm Use two raising kits*
* optional accessory
The dryer must not be used without
the front panel in place.
When moving the dryer do not hold
it by the door.
If the kitchen run has a continuous
furniture plinth in place, a gap must
be made for the tumble dryer.
37
Installation
Aligning the appliance
Room in which the dryer is located
Air taken in for use in the drying
process will be warm when it is
expelled from underneath the dryer.
This expelled air heats up the air in the
room. It is therefore very important to
ensure that the room is adequately
ventilated, particularly if the dryer is
located in a small room. Otherwise
running times and energy consumption
could be increased.
Washer-dryer stack
^ Turn the 4 screw feet to adjust the
dryer to the correct height and level.
Longer screw feet are available as
an optional accessory. Unscrew and
remove the feet supplied with the
dryer before fitting the longer screw
feet.
The cover plate on the dryer must
be aligned horizontally underneath
the worktop.
,The ventilation gaps in the plinth
must not be covered over as this
would prevent a sufficient intake of
air.
38
The tumble dryer can also be
combined with a Miele washing
machine in a washer-dryer stack. To do
this the appropriate stacking kit (WTV)
(available to order) is required.
,The stacking kit must be fitted by
suitably qualified fitter.
Before moving the tumble dryer
again (e.g. when moving house)
After each use a small quantity of
condensed water will collect in the area
around the pump. This water can run
out, if the dryer is tipped up when it is
being moved. It is a good idea to run
the Cool air programme for
approximately 1 minute before moving
the dryer. Any remaining condensed
water will then be fed into the
condensed water container or out
through the drain hose.
Installation
Matching the fascia panel to
the height of adjacent drawer
fronts
The fascia panel can be aligned with
the drawer fronts by adjusting the
spacer bars.
Removing the spacer bars
All the spacer bars can be removed if
the upper edge of the front panel needs
to be flush with the upper edge of the
appliance front directly underneath the
fascia panel. See "Fitting a front panel
made by another manufacturer".
^ Open the door.
^ Using a socket spanner, turn
clockwise or anti-clockwise until the
required height is reached.
If necessary individual bars can be
removed or more added.
^ To do this, use the socket spanner to
loosen the nuts.
An adapter kit with spacer bars and
longer screws can be ordered as an
optional accessory. This can be used to
add spacer bars from below up to a
maximum of 25 mm.
^ Unscrew and remove the 3 screws
(see arrows).
^ Remove all the spacer bars.
The 3 holes which are now free should
be used to screw the front panel to the
machine front later on.
After fitting the bars, cut or pinch off
any excess length from the screws.
39
Installation
Fitting the front panel
Fitting the front panel
The appliance front can be fitted with a
door panel to match other kitchen units.
^ Open the door.
If fitted in a Miele kitchen, the door
panel can be ordered pre-drilled with
the necessary fixing holes.
^ Hold the front panel in the correct
position in front of the appliance
If fitted in a non-Miele kitchen, a
suitable panel will have to be drilled
to suit by a qualified kitchen fitter.
See "Fitting a door front panel made
by another manufacturer" for details
on preparing and drilling the fixing
holes.
Front panel dimensions
Width: 592-596 mm
Thickness: 17 to 19 mm (corresponding
to the thickness of the adjacent unit
door front panels)
door.
^ Screw the front panel to the machine
door.
If all the spacer bars have been
removed:
You can also make use of the 3 holes at
the top of the door plate to screw the
front panel to the door plate.
Height: The height of the door front
panel corresponds to the door height
(H) of the adjacent units.
40
Installation
Fitting a door front panel made
by another manufacturer
B Mark the two hinge holes and the
four smaller holes as shown in the
diagram.
Preparing the front panel
For left hand hinging only:
A Measure distance X for drilling the
hinge holes.
– front panel shown decor side face
down, upper edge at the bottom:
– with spacer bars:
– without spacer bars:
(the front panel must be
correspondingly higher)
if width (b) increases, measurement a
must also be increased
b=
b=
b=
b=
b=
592 mm N a = 21.5 mm
593 mm N a = 22.0 mm
594 mm N a = 22.5 mm
595 mm N a = 23.0 mm
596 mm N a = 23.5 mm
H = height of adjacent furniture unit
doors.
41
Installation
For right hand hinging only:
– front panel shown decor side face
down, upper edge at the bottom:
C Drill the two hinge holes (C 35
mm/15.5 mm deep) in the back of
the front panel.
D Next, drill the four smaller holes
(C 7 mm/10 mm deep) in the back of
the front panel.
E Shorten the front panel from the
bottom to height H.
Preparing the fixing points
F Hold the pre-drilled front panel in the
correct position in front of the
machine door.
if width (b) increases, measurement a
must also be increased
b=
b=
b=
b=
b=
592 mm N a = 21.5 mm
593 mm N a = 22.0 mm
594 mm N a = 22.5 mm
595 mm N a = 23.0 mm
596 mm N a = 23.5 mm
H = height of adjacent furniture unit
doors.
G Mark the fixing points on the back of
the front panel through the holes in
the machine door plate (see arrows
in the illustration).
H Remove the front panel.
I Now drill holes (C 2.5 mm/10 mm
deep) in the back of the front panel.
42
Installation
Fitting a plinth facing
Useful tip:
The gap between the lower edge of the
tumble dryer plinth and the floor can be
closed up using a suitable kitchen
furniture plinth facing.
If the dryer is fitted on a raising kit, you
can use double-sided adhesive tape on
the back of the plinth facing to secure it
to the raising kit.
The tumble dryer plinth has a special
groove in which a plinth facing can be
fitted.
Plinth facing dimensions
Length: 592 - 596 mm
Thickness: 8 mm
Height (H): The plinth facing height
must be calculated after aligning the
height of the appliance with the screw
feet or after fitting the raising kit(s).
Installation
^ Calculate height (H) from the floor up
into the groove (on the underside of
the tumble dryer).
^ Cut the plinth facing to size.
^ Slide it into the groove.
43
Installation
External condensed water
outlet
General notes
When drying is in progress, condensed
water is pumped into the condensed
water container through the drain hose
at the back of the dryer. The
condensed water can also be drained
off directly if the dryer is installed near a
sink, drain outlet etc. so that the
condensed water container does not
have to be emptied.
Drain hose length . . . . . . . . . . . . 1.00 m
^ Unclip the drain hose from clips (1)
and (2).
Extension hose . . . . . . . . . . . . . . 2.00 m
(accessory)
^ Then pull it off connection (3).
Maximum delivery head . . . . . . . 1.50 m
Maximum drain hose length . . . . 4.00 m
,If the on-site water drainage
system is not fitted with a non-return
valve or an appropriate air gap, an
air gap or the non-return valve
supplied with the dryer must be
fitted to prevent the risk of
back-flow. (See "Installation
conditions requiring a non-return
valve").
Maximum delivery head
with non-return valve fitted . . . . . 1.00 m
Arranging the drain hose
,Do not pull on the drain hose
and do not stretch it or allow it to
become kinked as it could get
damaged.
44
^ The lower clip (4) can be opened to
allow you to take the drain hose out
or to feed the mains cable through it.
Installation
External drainage via a sink or gully
^ See "Front view" illustration.
,If you want to drain the water off
into a sink you will need to secure
the hose carefully, e.g. by tying it to
a tap to make sure it cannot slip
during use. Otherwise there is a risk
of overflowing water which could
cause damage.
Example: Connection to a sink drain
outlet
The drain hose with non-return valve
fitted can be connected directly to a
suitable sink drain outlet.
^ Use the bow-shaped guide to
prevent the drain hose from
becoming kinked (see "Front view"
illustration).
Installation conditions requiring a
non-return valve
,If the on-site water drainage
system is not fitted with a non-return
valve or an appropriate air gap, an
air gap or the non-return valve
supplied with the machine must be
fitted to prevent the risk of
back-flow. Otherwise water could
leak out of the dryer and cause
damage.
^ Remove the following from the back
of the dryer at the bottom:
Adapter 1 and hose clip 3 behind it.
A non-return valve is required:
– If the tumble dryer is connected to a
sink drain outlet (see the following
section).
– If the tumble dryer is to be
connected to a drainage system
already in use by another
appliance, e.g. a dishwasher or
washing machine.
45
Installation
^ Fit adapter 1 to the sink drain outlet
using nut 2.
If this nut has a flat disc in it you
should take the disc out first.
^ Attach the end of the extension hose
4 to adapter 1.
^ Use a screwdriver to tighten hose
clip 3 up close to the nut.
,Non-return valve 5 has to be
fitted with the arrow pointing in the
direction of flow (i.e. towards the
sink). Otherwise water will not drain
out of the machine.
1 Adapter
2 Nut
3 Hose clip
4 Extension hose (accessory)
5 Non-return valve (accessory)
6 Tumble dryer drain hose
46
^ Fit non-return valve 5 to the drain
hose on the dryer 6 (make sure it is
fitted correctly (see arrow on
non-return valve).
^ Secure the non-return valve using
hose clips.
Electrical connection
Electrical connection U.K.
Non-rewireable plugs BS 1363
All electrical work should be carried out
by a suitably qualified and competent
person, in strict accordance with
current national and local safety
regulations (BS 7671 in the UK).
The fuse cover must be refitted when
changing the fuse, and if the fuse cover
is lost, the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words on the base of the
plug (as applicable to the design of
plug fitted).
Ensure power is not supplied to the
appliance until after installation work
has been carried out.
The appliance is supplied with a mains
cable with moulded plug ready for
connection to a 230-240V mains
supply. Please ensure the connection
data quoted on the data plate match
the household mains supply.
Connection should be made via a
suitable switched socket which is easily
accessible after installation.
For extra safety it is advisable to protect
the appliance with a suitable residual
current device (RCD). Contact a
qualified electrician for advice.
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.
WARNING: THIS APPLIANCE
MUST BE EARTHED
Do not connect via an extension lead.
Extension leads do not guarantee the
required safety of the appliance (e.g.
danger of overheating).
47
Consumption data
Programme
Load
Final spin speed
in a domestic washing machine
Energy
Duration
kg*
rpm
kWh
Minutes
Cottons
Normal
6.0
1000 (60 % residual moisture)**
1200
1400
1600
1800
3.35
3.05
2.90
2.55
2.50
94
86
82
74
73
Cottons
Hand iron
6.0
1000 (60 % residual moisture)**
1200
1400
1600
1800
2.65
2.35
2.20
1.90
1.80
71
63
60
52
51
Minimum iron Normal
3.0
1200 (40 % residual moisture)**
1.15
34
Minimum iron Hand iron
3.0
1200
1.05
31
Delicates Normal
2.0
800
1.20
81
Automatic Normal
3.5
800
2.10
119
Shirts Normal
2.0
600
1.25
43
Denim Normal
3.0
900
2.40
119
Woollens handcare
2.0
1000
0.15
4
Silks handcare
1.0
400
0.15
5
Smoothing
3.0
1000
0.30
8
Outerwear Normal
2.0
800
1.40
72
* Weight of dry laundry
** EN 61121:2005 test programme
All data without a "star" against it was calculated using EN 61121:2005.
Before testing in accordance with EN 61121, dry a 3 kg load of cotton laundry with 70% residual
moisture as per the above standard using the Cottons Normal programme without any extra options.
Consumption data can vary from the nominal values given above depending on the size of the
load, types of textiles, residual moisture levels after spinning, fluctuations in the electricity
supply and any extra options selected.
48
Technical data
Height
820 mm
Width
595 mm
Depth
Suitable for stacking
575 mm
Yes
Weight
Drum volume
54 kg
100 litres
Maximum capacity
6 kg dry weight
Capacity of condensed water container approx. 3.5 litres
Drain hose length
Maximum delivery head
950 mm
1.5 m
Maximum drain hose length
Length of connection cable
4m
2m
Voltage
Connected load
see data plate
see data plate
Fuse rating
Lamp wattage
see data plate / plug
see data plate
Energy consumption
Test certificates awarded
see "Consumption data"
see data plate
49
Programmable functions
for changing default settings
The programmable functions are
used to alter the tumble dryer´s
electronics to suit changing
requirements.
Programmable functions can be
altered at any time.
50
Programmable functions
Extending the range of the
drying levels
You can extend the range of the
drying levels for many of the
programmes:
Machine iron+
(drier than Machine iron).
Hand iron+
(drier than Hand iron).
Normal+
(drier than Normal).
In addition the Extra dry drying level
can be made available for the
Delicates and Denim programmes.
You can use this programmable
function to extend the range of the
drying levels for the following
programmes:
Cottons, Minimum iron*, Delicates,
Automatic, Denim.
* Machine iron+ cannot be
programmed for this programme.
Follow steps A to E to programme
and store in memory.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
– The Low temperature indicator light
will briefly flash on and off twice.
– P and 0 (default setting) will flash
alternately in the display.
The number which appears alternately
in the display with P means:
0 Default setting
1 Drying level range extended
(The Automatic indicator light will
also flash).
D Pressing the Start/Stop button
switches from one to the other.
E Switch the dryer off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
To select the extended drying level
^ Select a programme.
^ Press the drying level button
repeatedly until one or two indicator
lights come on.
– Indicator lights Extra dry and Normal
= Normal+
– Indicator lights Hand iron and
Normal = Hand iron+
– Indicator lights Machine iron and
Hand iron = Machine iron+
B Press the I-On/0-Off button in.
Wait until the indicator light for the
Start/Stop button lights up
constantly . . .
C . . . and then release the Start/Stop
button.
51
Programmable functions
Altering the volume of the
buzzer
The buzzer has two volumes.
Follow steps A to F to programme
and store in memory.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Press the I-On/0-Off button in.
Wait until the indicator light for the
Start/Stop button lights up
constantly . . .
C . . . and then release the Start/Stop
button.
D Press the Low temperature button
once.
– The Low temperature indicator light
will briefly flash on and off four times.
– P and 0 (default setting) will flash
alternately in the display.
The number which appears alternately
in the display with P means:
0 Normal buzzer
(Default setting)
i Loud buzzer
(The Automatic indicator light will
also flash).
E Pressing the Start/Stop button
switches from one to the other. You
will hear the two buzzer volumes as
you do so.
F Switch the dryer off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
52
Programmable functions
Memory function
The electronics will memorise any
extra options selected for a
programme.
The duration selected for a timed
drying programme will also be stored
in memory.
These settings will be selected
automatically the next time the
programme is chosen. You can either
accept these or change them by
pressing the appropriate button.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Press the I-On/0-Off button in.
Wait until the indicator light for the
Start/Stop button lights up
constantly . . .
C . . . and then release the Start/Stop
button.
D Press the Low temperature button
twice.
Follow steps A to F to programme
and store in memory.
– The Low temperature indicator light
will briefly flash on and off six times.
Before you begin, first ensure that:
– P and 0 (default setting) will flash
alternately in the display.
– The tumble dryer is switched off.
– The door is closed.
The number which appears alternately
in the display with P means:
0 Memory deactivated
(Default setting).
i Memory activated
(The Automatic indicator light will
also flash).
E Pressing the Start/Stop button
switches from one to the other.
F Switch the dryer off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
53
Programmable functions
Extending the cooling down
time
The cooling down phase which takes
place before the end of a programme
can be lengthened if required. This
makes the garments easier to handle.
The cooling down time
– can be extended by 5 minutes or 10
minutes.
– is not available for timed drying,
smoothing or handcare programmes.
Follow steps A to F to programme
and store in memory.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Press the I-On/0-Off button in.
Wait until the indicator light for the
Start/Stop button lights up
constantly . . .
C . . . and then release the Start/Stop
button.
D Press the Low temperature button
three times.
– The Low temperature indicator light
will briefly flash on and off seven
times.
– P and 0 (default setting) will flash
alternately in the display.
The number which appears alternately
in the display with P means:
0 Default setting
i The cooling down time will be five
minutes longer.
(The Automatic indicator light will
also flash once).
2 The cooling down time will be ten
minutes longer.
(The Automatic indicator light will
also flash twice).
E Pressing the Start/Stop button
switches from one to the other.
F Switch the dryer off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
54
Programmable functions
Clean out airways indicator
Fluff should be removed after drying.
The Clean out airways indicator will
remind you to clean the filters when a
certain amount of fluff has collected
in the filters. You can decide at what
level of fluff this reminder should be
given.
You will have an idea of which of the
four options to select after a few drying
programmes.
Follow steps A to F to programme
and store in memory.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Press the I-On/0-Off button in.
Wait until the indicator light for the
Start/Stop button lights up
constantly . . .
C . . . and then release the Start/Stop
button.
D Press the Low temperature button
four times.
– The Low temperature indicator light
will flash on and off slowly once.
– P and 2 (default setting) will flash
alternately in the display.
The number which appears alternately
in the display with P means:
0 The Clean out airways indicator
light is deactivated
I The Clean out airways indicator
light will come on when there is a
heavy build-up of fluff
(The Automatic indicator light will
also flash once).
2 Default setting
(the Automatic indicator light will also
flash twice).
3 The Clean out airways indicator
light will come on when there is
only a light build-up of fluff
(The Automatic indicator light will
also flash three times).
E Pressing the Start/Stop button
switches from one to the other.
F Switch the dryer off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
55
Programmable functions
Keypad tone
An audible tone sounds each time a
button is pressed.
Follow steps A to F to programme
and store in memory.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Press the I-On/0-Off button in.
Wait until the indicator light for the
Start/Stop button lights up
constantly . . .
C . . . and then release the Start/Stop
button.
D Press the Low temperature button
five times.
– The Low temperature indicator light
will flash on and off slowly once and
will then flash on and off quickly
once.
– P and 0 (default setting) will flash
alternately in the display.
The number which appears alternately
in the display with P means:
0 Keypad tone deactivated
(Default setting)
i Keypad tone activated
(The Automatic indicator light will
also flash)
E Pressing the Start/Stop button
switches from one to the other.
F Switch the dryer off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
56
Programmable functions
Adjusting the dryer's
electronics for very soft water
,Extremely soft water can affect
the sensitivity of the control
electronics. If the dryer is installed in
an area with very soft water, you
should contact your local water
supplier for information and advice
regarding water hardness and water
conductivity. If the water
conductivity is less than 150 µS, the
following programmable function will
need to be activated.
Important. This programmable
function should not be activated if,
despite the water being extremely
soft (as would be the case if a water
softener were used), its conductivity
is greater than 150 µS.
Follow steps A to F to programme
and store in memory.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Press the I-On/0-Off button in.
Wait until the indicator light for the
Start/Stop button lights up
constantly . . .
C . . . and then release the Start/Stop
button.
D Press the Low temperature button six
times.
– The Low temperature indicator light
will flash on and off slowly once and
will then flash on and off quickly
twice.
– P and 0 (default setting) will flash
alternately in the display.
The number which appears alternately
in the display with P means:
0 Default setting
i Adjusted for very soft water
(with low conductivity)
(The Automatic indicator light will
also flash)
E Pressing the Start/Stop button
switches from one to the other.
F Switch the dryer off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
57
58
59
Alteration rights reserved/3809
M.-Nr. 06 984 111 / 03