Yamaha CD-N301 Owner`s manual

AB
Network CD Player
OWNER’S MANUAL
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Install this sound system in a well ventilated, cool, dry,
clean place - away from direct sunlight, heat sources,
vibration, dust, moisture, and/or cold. For proper
ventilation, allow the following minimum clearances.
Top: 10 cm (4 in)
Rear: 10 cm (4 in)
Sides: 10 cm (4 in)
Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
Do not expose this unit to sudden temperature changes
from cold to hot, and do not locate this unit in an
environment with high humidity (i.e. a room with a
humidifier) to prevent condensation inside this unit,
which may cause an electrical shock, fire, damage to this
unit, and/or personal injury.
Avoid installing this unit where foreign object may fall
onto this unit and/or this unit may be exposed to liquid
dripping or splashing. On the top of this unit, do not
place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and
liquid may cause electrical shock to the user and/or
damage to this unit.
Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If the
temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
Do not plug in this unit to a wall outlet until all
connections are complete.
Do not operate this unit upside-down. It may overheat,
possibly causing damage.
Do not use force on switches, knobs and/or cords.
When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
Only voltage specified on this unit must be used. Using
this unit with a higher voltage than specified is dangerous
and may cause fire, damage to this unit, and/or personal
injury. Yamaha will not be held responsible for any
damage resulting from use of this unit with a voltage
other than specified.
To prevent damage by lightning, keep the power cable
and outdoor antennas disconnected from a wall outlet or
this unit during a lightning storm.
Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any service is
needed. The cabinet should never be opened for any
reasons.
When not planning to use this unit for long periods of
time (i.e. vacation), disconnect the AC power plug from
the wall outlet.
Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit
is faulty.
i En
17 Before moving this unit, press to set this unit to the
standby mode, and disconnect the AC power plug from
the wall outlet.
18 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the power
cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may
become warm. Turn the power off, then leave this unit
alone for cooling.
20 Install this unit near the AC outlet and where the AC
power plug can be reached easily.
21 The batteries shall not be exposed to excessive heat such
as sunshine, fire or the like.
– Keep the batteries in a location out of reach of
children. Batteries can be dangerous if a child were to
put in his or her mouth.
– If the batteries grow old, the effective operation range
of the remote control decreases considerably. If this
happens, replace the batteries with two new ones as
soon as possible.
– Do not use old batteries together with new ones.
– Do not use different types of batteries (such as
alkaline and manganese batteries) together. Read the
packaging carefully as these different types of
batteries may have the same shape and color.
– Exhausted batteries may leak. If the batteries have
leaked, dispose of them immediately. Avoid touching
the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment
thoroughly before installing new batteries.
– If you plan not to use the unit for a long period of
time, remove the batteries from the unit. Otherwise,
the batteries will wear out, possibly resulting in a
leakage of battery liquid that may damage the unit.
– Do not throw away batteries with general house
waste. Dispose of them correctly in accordance with
your local regulations.
22 Excessive sound pressure from earphones and
headphones can cause hearing loss.
This unit is not disconnected from the AC power source as long as
it is connected to the wall outlet, even if this unit itself is turned off
by . This state is called the standby mode. In this state, this unit is
designed to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CONTENTS
OTHERS
WHAT YOU CAN DO WITH THIS UNIT ................. 2
FREQUENTLY ASKED QUESTIONS......................31
TROUBLESHOOTING ...............................................32
Sources that can be played back on this unit ..................... 2
Devices that can control this unit....................................... 3
Operations from your mobile device ................................. 3
Front panel ......................................................................... 5
Remote control................................................................... 6
Rear panel .......................................................................... 8
Front panel display............................................................. 8
CONNECTIONS ............................................................ 9
Connecting to an amplifier................................................. 9
Connecting to a network
(PC/NAS/Internet connection)..................................... 10
Turning on this unit.......................................................... 11
Playable media and devices ............................................. 38
Playable discs and file formats ........................................ 39
SPECIFICATIONS.......................................................40
(at the end of this manual)
Information about third party software
licenses ..........................................................i
OPERATIONS
SUPPLIED ACCESSORIES ......................................... 4
REMOTE CONTROL PREPARATION..................... 4
CONTROLS AND FUNCTIONS ................................. 5
Front panel display messages........................................... 36
ADDITIONAL INFORMATION ................................37
PLAYABLE DISCS AND FILE FORMATS .............38
PREPARATION
PREPARATION
OTHERS
OPERATIONS
SETUP OF YOUR NETWORK DEVICES............... 12
Sharing music files stored on your PC............................. 13
PLAYBACK OF CDS .................................................. 14
Playing back a CD ........................................................... 14
Using A-B repeat playback .............................................. 16
Using program playback mode ........................................ 16
PLAYBACK OF PANDORA® .................................... 17
Account setup for Pandora............................................... 17
Creating Pandora stations ................................................ 18
Playback of Pandora stations ........................................... 19
Deleting Pandora stations ................................................ 21
Editing the Pandora accounts........................................... 21
PLAYBACK OF SPOTIFY SERVICE ...................... 22
PLAYBACK OF MUSIC FILES ON YOUR
PC/NAS...................................................................... 23
Operations from the main unit or remote control ............ 23
PLAYBACK OF INTERNET RADIO ....................... 25
PLAYBACK OF AirPlay............................................. 27
Playing iPod ..................................................................... 27
Playing iTunes ................................................................. 27
Clearing AirPlay .............................................................. 27
SETUP MENU .............................................................. 28
Setup menu operations ..................................................... 28
Setup menu items............................................................. 29
Advanced setup menu ...................................................... 29
Updating the firmware ..................................................... 30
• Notes contain important information about safety and operating instructions. y indicates a tip for your operation.
• “iPod” described in this manual may also refer to “iPhone” or “iPad”.
1 En
English
About this manual
PREPARATION
WHAT YOU CAN DO WITH THIS UNIT
This unit is a network CD player, on which you can enjoy playing back music files stored on your media server (PC or
NAS), audio contents on the Internet radio, CD, Pandora, Spotify, AirPlay devices (iPod/iTunes), by connecting the unit
to your home network (DLNA) and audio system on the same network.
y
For details on DLNA or NAS, see “ADDITIONAL INFORMATION” (☞ P.37).
Sources that can be played back on this unit
Amplifier
1 Internet
2 Pandora service
7 CD
Modem
SELECT
ENTER
SOURCE
PUSH
PURE DIRECT
RETURN
Broadband router*
This unit (CD-N301)
3 PC
4 NAS
5 iPod (AirPlay)*
6 iPod/Android (Spotify)*
* You need a commercially available Wi-Fi broadband router when you use an iPod/Android.
1 Play back the Internet radio (☞ P.25)
5 Play back your iPod with AirPlay (☞ P.27)
2 Play back the Pandora service (☞ P.17)
6 Play back the Spotify service (☞ P.22)
3 Play back music files stored on your PC
7 Play back a CD (☞ P.14)
(☞ P.12, 23)
4 Play back music files stored on your NAS
(☞ P.12, 23)
y
For details on connecting the devices, see “CONNECTIONS” (☞ P.9).
2 En
WHAT YOU CAN DO WITH THIS UNIT
Devices that can control this unit
PREPARATION
SELECT
ENTER
SOURCE
PUSH
PURE DIRECT
RETURN
Broadband router*
A
B
Mobile device*
(iPod, Android)
Remote control
* You need a commercially available Wi-Fi broadband router when you use a mobile device.
A Control this unit using your mobile devices (☞ P.3, 12)
B Control this unit using the remote control (☞ P.6, 14, 17, 23, 25, 28)
Operations from your mobile device
Once you install the app “NETWORK PLAYER CONTROLLER” in your mobile device, you can operate the unit with
the mobile device.
Features
•
•
•
•
Power-on/off or other basic operation
Changing the music source
Selecting, playing back, and stopping songs
Playing back songs stored in devices
For downloading the app or the latest information, access to the App Store or Google Play and search “NETWORK
PLAYER CONTROLLER.”
English
3 En
PREPARATION
SUPPLIED ACCESSORIES
Check that you have received all of the following items.
Remote control
OPEN/CLOSE
RCA stereo cable
Power cable
Batteries (AA, R6, UM-3) (× 2)
Owner’s manual
DIMMER
PURE DIRECT
SOURCE
1
2
4
5
3
6
7
8
9
0
PROGRAM
CLEAR
REPEAT
A/B
SHUFFLE
POP-UP MENU
HOME
NOW PLAYING
ENTER
SETUP
RETURN
DISPLAY
OPTION
AMP
INPUT
VOLUME
MUTE
REMOTE CONTROL PREPARATION
❚ Installing the batteries
1 3
❚ Operation range
Aim the remote control directly at the remote control
sensor on the main unit during operation.
Remote control sensor
2
SELECT
ENTER
PUSH
RETURN
Notes
• Change all batteries if the operation range of the remote control
narrows.
• Before inserting new batteries, wipe the compartment clean.
Within 6 m (20 ft)
30
30
OPEN/CLOSE
DIMMER
PURE DIRECT
SOURCE
1
2
4
5
7
8
9
0
PROGRAM
CLEAR
REPEAT
POP-UP MENU
3
6
A/B
SHUFFLE
HOME
NOW PLAYING
ENTER
SETUP
RETURN
DISPLAY
OPTION
AMP
INPUT
4 En
VOLUME
MUTE
CONTROLS AND FUNCTIONS
PREPARATION
Front panel
1
5
6
SELECT
ENTER
SOURCE
PUSH
PURE DIRECT
RETURN
2
3 4
1 Power indicator
• Lights up:
The unit is on.
• Lights up dimly:
The unit is in standby mode.
• Off:
The unit is off.
7
8 90 A
B C
5 Disc tray
Loads a disc.
6
(Open/Close)
Opens or closes the disc tray.
7 Front panel display
Shows menu items, playback information, etc.
y
y
When the unit is in standby mode, you can control the power
from a network device (network standby). To enable network
standby function, set “System Config” → “Network Standby”
to “On” from the setup menu (☞ P.28).
For details on display messages, see “Front panel display
messages” (☞ P.36).
2 Power switch (☞ P.11)
Switches this unit between on and off.
: On
: Off
3 SOURCE (☞ P.14, 17, 23, 25)
Selects an audio source. Each press cycles the audio sources
as follows.
CD → Pandora* → Spotify → Server → Net Radio → AirPlay
→ Back to CD
(* Australia model only)
4 PURE DIRECT
Turns on or off PURE DIRECT mode. Audio quality will be
improved when PURE DIRECT mode is on.
Note
8 Remote control sensor (☞ P.4)
Receives infrared signals from the remote control.
9
/ (Play/Pause)
Starts or pauses playback.
0
(Stop)
Stops playback.
A
/
(Skip/Search backward)
Skips backward. Searches tracks backward while the button
is pressed and held during playback.
/
(Skip/Search forward)
Skips forward. Searches tracks forward while the button is
pressed and held during playback.
B SELECT/ENTER (jog dial) (☞ P.14, 23, 25, 29)
Rotate to select an item and press to confirm the selection.
C RETURN (☞ P.23, 25)
Shows the upper-level menu in the front panel display.
The digital output is turned off when this unit is in PURE
DIRECT mode.
y
The PURE DIRECT indicator lights up when PURE
DIRECT mode is on.
English
5 En
CONTROLS AND FUNCTIONS
Remote control
1 Remote control signal transmitter
Transmits infrared signals to the main unit.
2 OPEN/CLOSE
Opens or closes the disc tray.
1
3 DIMMER
You can adjust the brightness of the front panel display in the
following three stages: bright, mid dim, or dim. Each press of
the button changes the brightness.
2
3
4
4 SOURCE (☞ P.14, 17, 23, 25)
Selects an audio source. Each press cycles the audio sources
as follows.
CD → Pandora* → Spotify → Server → Net Radio → AirPlay
→ Back to CD
(* Australia model only)
5
6
7
8
9
OPEN/CLOSE
B
E
PURE DIRECT
SOURCE
1
2
3
4
5
6
7
8
9
0
PROGRAM
CLEAR
REPEAT
A/B
SHUFFLE
POP-UP MENU
HOME
NOW PLAYING
0
A
DIMMER
F
5 Numeric buttons (☞ P.15)
Use to enter numbers, such as the track number of a CD.
6 REPEAT (☞ P.15, 24)
Switches repeat modes.
G
H
I
J
RETURN
DISPLAY
OPTION
C
8 POP-UP MENU
This button is not available for this unit.
9 HOME (☞ P.19, 23, 26)
Moves up top level when selecting (browsing) music files,
folders, etc.
0 /// (Cursor buttons)/ENTER
Use the cursor buttons to select an item and press ENTER to
confirm the selection.
Change the playback folder or the music file when playing
music files on your data CDs, PC or NAS.
ENTER
SETUP
7 A/B (☞ P.16)
Repeats playback of a specified section of a track during
audio CD playback (A-B repeat playback).
K
L
A SETUP (☞ P.28)
Shows the setup menu in the front panel display.
B DISPLAY (☞ P.15, 20, 24, 26)
Switches information shown in the front panel display, such
as playback information.
C Playback buttons (☞ P.15, 20, 24, 26, 27)
AMP
D
INPUT
VOLUME
(Play/Pause)
Starts or pauses playback.
MUTE
(Stop)
Stops playback.
(Skip backward/Search backward)
Skips backward. Searches tracks backward while the button
is pressed and held during playback.
(Skip forward/Search forward)
Skips forward. Searches tracks forward while the button is
pressed and held during playback.
6 En
CONTROLS AND FUNCTIONS
D Amplifier control buttons
Controls the corresponding functions of a Yamaha amplifier.
PREPARATION
A (Power)
Turns your amplifier on and off.
INPUT ( / )
Switches input sources.
VOLUME ( / )
Adjusts the volume.
MUTE
Turns mute on or off.
For details on operations, refer to the manual of your
amplifier.
y
These buttons may not work for some Yamaha amplifiers.
E A (Power) (☞ P.11)
Switches this unit between on and standby mode.
F PURE DIRECT
Turns on or off PURE DIRECT mode. Audio quality will be
improved when PURE DIRECT mode is on.
Note
The digital output and front panel display are turned off
when this unit is in PURE DIRECT mode.
G CLEAR (☞ P.16)
Clears the last programmed track of an audio CD during
program editing mode.
Clears all programmed tracks when playback is stopped
while exiting the program mode.
H PROGRAM (☞ P.16)
Turns on or off program playback mode. In program
playback mode, you can playback tracks of an audio CD in a
programmed sequence.
I SHUFFLE (☞ P.15, 24)
Switches shuffle modes.
J NOW PLAYING (☞ P.19, 23, 26)
Displays playback information when selecting (browsing)
music files, folders, etc.
K RETURN (☞ P.21, 24, 26, 28)
Moves up one level when selecting (browsing) music files,
folders, etc.
L OPTION (☞ P.18)
(U.K. model)
This button is not available for this unit.
(Australia model)
Displays the option menu during Pandora service playback.
English
7 En
CONTROLS AND FUNCTIONS
Rear panel
1
2 3
4
5
6
1 ANALOG OUT terminal (☞ P.9)
Outputs L/R analog audio signals. Connect to your amplifier
or audio system using the RCA stereo cable (supplied).
4 NETWORK terminal (☞ P.10)
Connects to a network using a network cable (commercially
available).
2 DIGITAL OUT terminal (COAXIAL) (☞ P.9)
Outputs digital audio signals. Connect to your amplifier or
audio system using a coaxial digital audio cable
(commercially available).
5 DC OUT terminal
Supplies power to the Yamaha AV accessories from this
terminal. When using this, set “Accessory” in “System
Config” from the setup menu, to “On” (☞ P.28). For details,
refer to the owner’s manual supplied with the accessory.
3 DIGITAL OUT terminal (OPTICAL) (☞ P.9)
Outputs digital audio signals. Connect to your amplifier or
audio system using an optical cable (commercially
available).
6 AC IN socket (☞ P.9)
Connects to an AC outlet using the power cable (supplied).
Front panel display
1
2
3
1FP
A B
1 Information display
Displays various information such as the song title.
y
For more information on the messages displayed, see “Front
panel display messages” (☞ P.36).
2 PROGRAM indicator
Lights up when the unit is in program playback mode
(☞ P.16).
3 REPEAT/SHUFFLE indicator (☞ P.14, 23)
Lights up when the unit is in repeat or shuffle mode.
Repeat playback
: REPEAT ALL
: REPEAT ONE
: REPEAT FOLDER
: A-B REPEAT
Shuffle playback
: SHUFFLE ALL
: SHUFFLE FOLDER
8 En
CONNECTIONS
Notes
•
•
•
•
Do not connect the power cable of this unit until all connections are completed.
You need to connect this unit to an amplifier and speakers before playing back.
This unit can output digital signals up to 192 kHz/24 bits linear PCM signals.
Proper playback may not be possible depending on the connected device and environment. Verify the settings and specifications of the
connected playback source device.
PREPARATION
This section describes connections required before playing back with this unit.
Connecting to an amplifier
This unit (CD-N301)
ANALOG OUT
R
L
DIGITAL OUT
COAXIAL
2
Power cable
(supplied)
OPTICAL
1
To AC outlet
1
2
3
Amplifier
Amplifier
* The digital output is turned off when this unit is in
PURE DIRECT mode.
1
Connect this unit to your amplifier with
one of the following cables.
Connect the supplied power cable to the
AC IN socket, then plug into an AC
outlet.
y
For details on speaker connections, refer to the manual of your
amplifier or speakers.
Note
When using a digital connection, audio output may be interrupted
at the beginning of a track depending on the audio system
(amplifier, etc.).
9 En
English
1 RCA stereo cable
(supplied)
2 Coaxial digital audio cable
(commercially available)
3 Optical digital cable
(commercially available)
2
CONNECTIONS
Connecting to a network (PC/NAS/Internet connection)
You can play back music files stored on your PC or NAS, audio contents on the Internet radio, by connecting this unit to
a network.
Connect with a commercially available STP (shielded twisted pair) network cable (CAT-5 or higher, straight-through
cable).
This unit (CD-N301)
Network cable
LAN
PC
Broadband router
WAN
NAS
Modem
Internet
Notes
• For details on Internet connection, refer to the owner’s manuals of your network devices.
• If you are using a router that supports DHCP, you do not need to configure any network settings for the unit. If you are using a router
that does not support DHCP, configure the network setting from “Network Config” in the setup menu (☞ P.28).
• Wired connections are recommended for devices other than the mobile to ensure high sound quality.
• Some security software installed on your PC or the firewall settings of network devices (such as a router) may block the access of the
unit to the network devices or the Internet. In this case, change the setting of the security software or network devices.
• When setting the subnet manually, each server must be connected to the same subnet as the unit (☞ P.28).
10 En
CONNECTIONS
Turning on this unit
When you have established all cable connections, turn on this unit and other system components.
PREPARATION
SELECT
ENTER
SOURCE
PUSH
PURE DIRECT
RETURN
Press the power switch to turn this unit on.
With the power switch on, you can switch this unit to on or standby mode by pressing the power button on the remote
control.
When network standby mode is enabled, you can also control the power etc. from a network device.
❚ Operable functions in standby/network standby
CD eject
AirPlay
Power-on by the
application
Standby
Operable
—
—
Network Standby
Operable
Operable
Operable
To enable network standby mode, set “System Config” → “Network Standby” to “On” from the setup menu (☞ P.28).
y
When no operations are performed for a specific length of time, the unit automatically switches to standby mode (auto power standby).
You can set the time to switch to standby mode in “System Config” → “AutoPowerStdby” from the setup menu (☞ P.28).
English
11 En
OPERATIONS
SETUP OF YOUR NETWORK DEVICES
Configure your devices connected to the network to play back music files stored on the devices, or configure your mobile
device to control this unit. Use the following configurations to suit your needs.
y
For details on Internet connection, please refer to the manual of your network devices.
❚ If you want to play the music files stored on your PC
You need to configure the media sharing setting of your PC.
Configure the media sharing setting of music files on
Windows Media Player 12. For details on sharing setting,
please refer to “Sharing music files stored on your PC”
(☞ P.13).
y
You can operate from your PC using Windows Media Player. For
details, refer to Windows Media Player help.
❚ If you want to play music files stored on your NAS
You need to configure the media sharing settings of your NAS.
Setup operations differ depending on your NAS. Refer to the
NAS manual.
y
• If you want to configure the network parameters manually, check
that you are using an IP address which is not used by other network
devices in your network.
• In case that you use DHCP and automatically obtain necessary
information for network, such as IP address. We recommend that
DHCP for the NAS normally be enabled.
❚ If you want to play iPod/iTunes with AirPlay
Select this unit from your iPod or from iTunes (☞ P.27).
Check that the router being accessed by the iPod/iTunes is
connected to the same network as this unit.
❚ If you want to operate this unit with your mobile device
You need to download the dedicated application, and install it
(☞ P.3).
y
• If you want to configure the network parameters manually, check
that you are using an IP address which is not used by other network
devices in your network.
• In case that you use DHCP and automatically obtain necessary
information for network, such as IP address. We recommend that
DHCP for the mobile device normally be enabled.
12 En
SETUP OF YOUR NETWORK DEVICES
Sharing music files stored on your
PC
4
Select “Allowed” from the drop-down
list next to “CD-N301”.
5
In the same way, select the icons for
devices to be used as external media
controllers (other PCs or mobile
devices), then click “Allowed”.
6
Click “OK” to exit.
To play back music files in your computer with this unit,
you need to make the media sharing setting between the
unit and computer (Windows Media Player 11 or later).
For details on Windows Media Player, please refer to
Windows Media Player help.
y
You can connect up to 16 media servers to this unit.
OPERATIONS
❚ When using Windows Media Player 12
(on Windows 7)
1
2
Start Windows Media Player 12 on your
PC.
Select “Stream”, then “Turn on media
streaming”.
❚ When using Windows Media Player 11
1
Start Windows Media Player 11 on your
PC.
2
Select “Library” then “Media Sharing”.
3
Check the “Share my media to” box,
select the “CD-N301” icon, then click
“Allow”.
4
In the same way, select the icons for
devices to be used as external media
controllers (other PCs or mobile
devices), then click “Allow”.
5
Click “OK” to exit.
The Control Panel window of your PC appears.
3
Click “Turn on media streaming”.
English
13 En
PLAYBACK OF CDS
This unit allows playback of audio CDs and data CDs in which the MP3/WMA files are recorded.
y
For details on playable CDs, see “PLAYABLE DISCS AND FILE FORMATS” (☞ P.38).
Front panel display (example)
3
CD
¡¡¡¡ 1¡¡¡ 0:01
Press / (main unit) or
control) to start playback.
(remote
Main unit/Remote control
ENTER
Icon
The following icons are shown on the front panel display.
Icon
SETUP
RETURN
DISPLAY
OPTION
Content
Displayed while a CD is being played back.
SELECT
ENTER
Displayed while a CD is paused.
PUSH
RETURN
Displayed when a CD is stopped.
4
Playing back a CD
When playback starts, use the following
controls to operate desired functions.
Main unit
1
Press SOURCE repeatedly to switch the
audio source to “CD”.
SELECT
ENTER
PUSH
SELECT/ENTER
Main unit/Remote control
RETURN
OPEN/CLOSE
SOURCE
SOURCE
Playback buttons
DIMMER
SOURCE
PURE DIRECT
1
2
3
4
5
6
SELECT/ Rotate
ENTER
Press
PURE DIRECT
Skips to the next track, or back to
the previous track.
Plays/Pauses.
Plays/Pauses.
/
Stops playback.
SOURCE
2
Set the CD.
Press the
(open/close) button on this unit, or press
the OPEN/CLOSE button on the remote control to
open the disc tray, and load a disc.
14 En
Playback
buttons
/
/
Press to skip to the next track, or
back to the previous track, or
hold down to search backward/
forward.
PLAYBACK OF CDS
Remote control
OPEN/CLOSE
DIMMER
4
Numeric
buttons
Sets the track number.
ENTER
When a music file is selected:
starts playback.
Plays/Pauses.
PURE DIRECT
SOURCE
1
Numeric buttons
2
5
Playback
buttons
6
8
9
0
PROGRAM
CLEAR
REPEAT
A/B
SHUFFLE
POP-UP MENU
HOME
NOW PLAYING
REPEAT
REPEAT
SHUFFLE
Select the shuffle playback
method.
Audio CD:
SHUFFLE ALL / SHUFFLE
OFF
Data CD:
SHUFFLE FOLDER /
SHUFFLE ALL / SHUFFLE
OFF
DISPLAY
Change the playback information.
Audio CD (during playback):
Playing time → Time remaining
→ Disc time remaining →
Song title* → Artist name →
Album title*
Data CD (during playback):
Playing time → Song title →
Artist name → Album title
ENTER
RETURN
DISPLAY
OPTION
Press to skip to the next track, or
back to the previous track, or hold
down to search backward/forward.
Select the repeat playback
method.
Audio CD:
REPEAT ONE / REPEAT ALL
/ REPEAT OFF
Data CD:
REPEAT ONE / REPEAT
FOLDER / REPEAT ALL /
REPEAT OFF
SHUFFLE
SETUP
/
/
DISPLAY
Playback
buttons
OPERATIONS
7
ENTER
Stops playback.
3
* Only for audio CDs that contain CD-TEXT.
y
• Files on a data CD are played back in alphanumeric order.
• When CD playback is stopped, playback will resume from the
beginning of the song last played. Pressing
while playback
is stopped will clear resume playback.
• You can also check the repeat/shuffle status from the indicators
on the front panel display (☞ P.8).
English
15 En
PLAYBACK OF CDS
Using A-B repeat playback
Using program playback mode
During audio CD playback, A-B repeat playback allows
you to specify the start and end points for a section that
you want to repeat.
In program playback mode, you can play back tracks in a
programmed sequence.
y
Program playback is only available for audio CDs.
y
A-B repeat playback is only available for audio CDs.
1
1
Playback the audio CD, and then press
the A/B button on the remote control at
the point you want to start the repeat.
7
8
9
0
PROGRAM
CLEAR
REPEAT
A/B
SHUFFLE
POP-UP MENU
HOME
NOW PLAYING
Press PROGRAM on the remote control
while playback is stopped.
This unit enters program editing mode.
PROGRAM
7
8
9
0
PROGRAM
CLEAR
REPEAT
A/B
SHUFFLE
POP-UP MENU
HOME
NOW PLAYING
CLEAR
A/B
ENTER
ENTER
ENTER
SETUP
RETURN
DISPLAY
OPTION
A B
The A-B indicator on the front panel display flashes
during setup.
2
Press the A/B button on the remote
control again at the point where you
want to end the repeat.
DISPLAY
OPTION
Select a track by using the numeric
buttons and press ENTER to confirm.
3
Repeat step 2 to program the next track.
You can program up to 50 tracks.
y
To cancel the programmed track, press CLEAR during program
editing mode. The last programmed track will be deleted.
4
Press /
unit or
control.
(Play/Pause) on the main
(Play/Pause) on the remote
Playback starts from the beginning of the
programmed sequence.
The A-B indicator turns lit, and the repeat playback
starts.
3
RETURN
2
Front panel display (example)
CD
¡¡¡¡¡2¡¡¡¡1:25
SETUP
y
To stop the repeat playback, stop the
playback, or press the A/B button again.
The repeat playback is cancelled.
To clear all programmed tracks, press CLEAR while playback is
stopped.
Note
The programmed tracks are cleared when the disc is ejected or
this unit is turned off.
16 En
PLAYBACK OF PANDORA®
(Australia model only)
The Pandora service is available in the U.S.A,
Australia, New Zealand only.
If you have not set up your Pandora account yet, the
account setup display appears when you select “Pandora”.
To start using the Pandora service on the unit, follow the
procedure below to set up your Pandora account.
y
You can register up to eight Pandora accounts on the unit. For
details, see p.21.
1
Remote control
OPEN/CLOSE
SOURCE
1
2
The following icons are shown on the front panel
display.
Icon
2
3
4
5
6
Front panel display
Pandora
¡Sign in
2
If you have a Pandora account, press
ENTER. If you do not have a Pandora
account, press / to select
“Activation” and press ENTER.
Remote control
Numeric buttons
1/2
Displayed when the setting/editing item
can be selected.
Displayed when the station list during
playback.
2
1
Content
Displayed an menu item or station list can
be selected.
1
PURE DIRECT
If you have not set up your Pandora account on the
unit yet, “Sign in” appears on the front panel display.
Front panel display (example)
Pandora
¡ Shuffle
DIMMER
SOURCE
Notes
• To use this function, the unit must be connected to the Internet.
For detail on connections and network settings (p.10).
• If any error message appears on the front panel display, see
“Front panel display messages” (p.36).
Press SOURCE repeatedly to switch the
audio source to “Pandora”.
OPERATIONS
Pandora is a free, personalized internet radio service that
plays only the music you love.
Enter a favorite artist, track or genre and Pandora will do
the rest, bringing an effortless personalized soundtrack
into your living room. Rate tracks with thumbs-up and
thumbs-down as they play, and Pandora will adapt stations
to your feedback on the spot.
Since all Pandora accounts are portable, you can always
access your own personalized Pandora stations from any
computer or device in the United States, Australia and
New Zealand that support Pandora. Pandora is currently
only available within these countries due to licensing
restrictions.
Pandora is always free, with the option to upgrade to
Pandora One which is completely free of all advertising
and comes with additional features.
For more information, http://www.pandora.com
Account setup for Pandora
Displayed when the setting/editing item
can be selected.
1
2
3
4
5
6
7
8
9
0
PROGRAM
CLEAR
REPEAT
A/B
SHUFFLE
POP-UP MENU
HOME
NOW PLAYING
////
ENTER
ENTER
English
SETUP
RETURN
17 En
PLAYBACK OF PANDORA®
3
Perform the following procedure.
If you select “Sign in” in Step 2
1 Use the /// to enter your Pandora account
e-mail address.
2 Press ENTER to enter password entry.
3 Use the /// to enter your Pandora password.
4 Press ENTER to access your account.
If you have successfully logged into your account,
“Login OK” appears on the front panel display.
Creating Pandora stations
Pandora lets you create up to 100 custom radio stations that
play only music you love. Just type in your favorite track or
artist and Pandora will create a station that plays similar music.
y
• If there are no Pandora stations in your account, the “Create”
appears automatically. In this case, proceed to Step 4 and create
Pandora stations.
• When the maximum number of Pandora stations have be been
created, “Max Stations” appears on the front panel display.
If “Create” appears on the front panel display, you
can create Pandora stations. Refer to step 4 in
“Creating Pandora stations” (p.18) for details.
1
y
Remote control
Press SOURCE repeatedly to switch the
audio source to “Pandora”.
• If you want to delete characters, press Numeric button “1”.
• If you want to insert characters, press Numeric button “2”.
• Rotate SELECT/ENTER on the front panel, you can
change characters quickly.
OPEN/CLOSE
SOURCE
Notes
When login goes failed, “Login Failed” appears on front
panel display.
– If you want to retry same password, press / to select
“Retry” and press ENTER.
– If you want to reset the password, select the “Forgot” and
press ENTER twice. An e-mail message containing a link to
reset your password will be sent to your e-mail address that
you entered in step 1. Please check your mail and click it.
1
2
3
4
5
6
The station list appears on the front panel display.
Front panel display (example)
Pandora
¡ Shuffle
station list
If you select “Activation” in Step 2
y
1 Write down the URL and active code shown in the
front panel display.
2 Use a web browser on your PC to access the URL
and follow the on-screen instruction to register for
a Pandora account.
3 After activation, press ENTER to log in with your
new Pandora account.
PURE DIRECT
SOURCE
Password
¡[Retry]Forgot
URL
http://www.pando
DIMMER
If HOME is pressed, the station list can be displayed at any
time. When a station list is not displayed, perform the
following operations after press HOME.
2
Press OPTION.
Remote control
Numeric buttons
1/2
If “Create” appears on the front panel display, you
can create Pandora stations. Refer to step 4 in
“Creating Pandora stations” (p.18) for details.
1
2
3
4
5
6
7
8
9
0
PROGRAM
CLEAR
REPEAT
A/B
SHUFFLE
POP-UP MENU
HOME
NOW PLAYING
HOME
////
ENTER
RETURN
ENTER
SETUP
RETURN
DISPLAY
OPTION
OPTION
18 En
PLAYBACK OF PANDORA®
3
4
Press / to select “Create Station”
and press ENTER.
Use the /// to enter the name of
an artist or a track (all or part of the
name) and press ENTER.
y
• If you want to delete characters, press Numeric button “1”.
• If you want to insert characters, press Numeric button “2”.
If you have created Pandora stations, follow the procedure
below to select a Pandora station to be played.
1
Press SOURCE repeatedly to switch the
audio source to “Pandora”.
Remote control
OPEN/CLOSE
Perform the following procedure.
DIMMER
SOURCE
If both artists and tracks are found
OPERATIONS
5
Playback of Pandora stations
PURE DIRECT
SOURCE
Create
¡[Artist]Track
1
2
3
4
5
6
1 Press / to select “Artist” or “Track” and press
ENTER.
2 Press / to select a desired item and press
ENTER.
The selected item is added to your Pandora
stations. The playback starts automatically and the
playback information is displayed.
Front panel display (example)
If either artists or tracks are found
Press / to select a desired item and press
ENTER.
The selected item is added to your Pandora stations.
The playback starts automatically and the playback
information is displayed.
• If playback of any Pandora station is ongoing, the playback
information is displayed.
• When a station list is not displayed, perform the following
operations after press HOME.
If only one item is found
In this case, the item found is automatically added to
your Pandora stations. The playback starts automatically
and the playback information is displayed.
Pandora
¡ Shuffle
station list
y
2
Use the following controls to select a
desired Pandora station.
Remote control
If no items are found
“No content” appears on front panel display. Press
ENTER and repeat Step 4 to try another keyword.
REPEAT
A/B
SHUFFLE
POP-UP MENU
HOME
NOW PLAYING
NOW PLAYING
HOME
//ENTER
y
ENTER
To return to the previous state, press RETURN.
//
ENTER
SETUP
RETURN
DISPLAY
OPTION
/
Selects a Pandora station.
ENTER
Starts playback.
HOME
Displays station list.
NOW PLAYING
Stops browsing and displays
playback information.
If you display the station list during playback,
of the Pandora station name.
appears at top
19 En
English
y
PLAYBACK OF PANDORA®
3
When playback starts, use the following
controls to operate desired functions.
I like it
Gives positive feedback (thumbs
up) for the current track.
(thumbs up) is displayed in the
track name.
I dont like it
Gives negative feedback (thumbs
down) for the current track and
skip to the next track. If you can
not skip at skip limit, (thumbs
down) is displayed in the track
name.
Tired of it
Requests not to playback the
current track for a month and skip
to the next track.
Remote control
ENTER
SETUP
RETURN
DISPLAY
OPTION
DISPLAY
Playback
buttons
If you want to bookmark current track
Plays/Pauses.
Playback
buttons
Skips to the next track.
/
Changes the playback
information (Track name and
Artist name → Station name →
Album title → Playing time).
DISPLAY
4
1 When the playback information is displayed, press
OPTION.
2 Press / to select “Bookmark” and press
ENTER.
“This Track” appears on the front display.
3 Press ENTER again.
Adds the current track to your bookmarks on your
Pandora profile page at “http://www.pandora.com”.
Stops playback.
If you want to confirm why you have to play
Perform the following procedure if you
needed.
1 When the playback information is displayed, press
OPTION.
2 Press / to select “WhyThisTrack?” and press
ENTER.
3 Return to previous state, press RETURN.
Remote control
REPEAT
A/B
SHUFFLE
POP-UP MENU
HOME
NOW PLAYING
y
Some functions are not available during advertisement broadcast.
//ENTER
ENTER
SETUP
RETURN
DISPLAY
OPTION
RETURN
OPTION
If you want to set a rating of track
1 When the playback information is displayed, press
OPTION.
2 Press / to select “RateThisTrack” and press
ENTER.
Pandora
¡I like it
3 Press / to select rating and press ENTER.
20 En
PLAYBACK OF PANDORA®
Deleting Pandora stations
The created Pandora station can be deleting in the
following procedures.
Remote control
Editing the Pandora accounts
You can register up to 8 Pandora accounts on the unit.
Follow the procedure below to add or remove Pandora
accounts, or switch to another Pandora account.
Remote control
REPEAT
A/B
SHUFFLE
POP-UP MENU
HOME
NOW PLAYING
HOME
///
ENTER
REPEAT
A/B
SHUFFLE
POP-UP MENU
HOME
NOW PLAYING
///
ENTER
SETUP
RETURN
DISPLAY
OPTION
OPERATIONS
ENTER
ENTER
SETUP
RETURN
DISPLAY
OPTION
RETURN
OPTION
OPTION
1
Press HOME to display the station list.
1
Press HOME to display the station list.
2
Press / to select Pandora station to
be delete.
2
Press OPTION.
3
Press OPTION.
3
Press / to select “Pandora Account”
and press ENTER.
4
Press / to select “Delete station”
and press ENTER.
4
Perform the following procedure.
To add a new Pandora account
5
Press / to select “OK” and press
ENTER.
Note
When you delete a Pandora station, that station is deleted from
your Pandora account and all associated listening devices.
1 Press / to select “Add Account” and press
ENTER.
2 Follow from Step 3 of “Account setup for
Pandora” (p.17).
y
When the Pandora account is created to the maximum,
“Max account” appears on the front display.
To remove a Pandora account
1 Press / to select “Remove Account” and press
ENTER.
2 Press / to select a Pandora account to be
removed and press ENTER.
3 Press / to select “OK” and press ENTER.
4 Return to previous state, press RETURN.
To switch to another Pandora account
1 Press / to select “Switch User” and press
ENTER.
2 Press / to select a Pandora account to be used
and press ENTER.
21 En
English
Pandora, the Pandora logo, and the Pandora trade dress are
trademarks or registered trademarks of Pandora Media, Inc.
Used with permission.
PLAYBACK OF SPOTIFY SERVICE
Spotify gives you instant access to millions of songs on your mobile devices. Just hit play to stream anything you like.
The Spotify Connect feature lets you choose music on your Spotify app and listen on your Yamaha home entertainment
system.
See Spotify.com for service area information.
1
Connect your device to your home Wi-Fi
network.
3
Connect the unit and your mobile device to your
home Wi-Fi network as shown in the illustration
below. All devices need to be on the same network.
Turn on the unit and playback of Spotify
contents.
Start Spotify app on your mobile device, log in to
Spotify and start playing a track.
1 Tap on the Now Playing bar to reveal extra
controls and tap the Speaker icon.
2 Select the unit (network name of the unit) as the
audio output device.
Network connection (example)
Internet
Spotify app (example)
Broadband router
1
Modem
This unit (CD-N301)
2
CD-N301 XXXXXX
Mobile device*
* iOS/Android™ apps are available as of July 2014.
For more details, visit Spotify.com
y
y
The playback screen is displayed on the front display.
To use this function, this unit and your mobile device must be
connected to the Internet. For detail on connections and network
settings, refer to “Owner’s Manual”.
2
Get Spotify app and premium free trial.
Download the Spotify app for your mobile device
from your app store, and take the Premium free trial.
The Spotify app and Premium account are required. Visit
spotify.com for details.
www.spotify.com/connect
22 En
Spotify and Spotify logo are registered trademarks of
the Spotify Group.
PLAYBACK OF MUSIC FILES ON YOUR PC/NAS
This unit allows you to play back music files such as MP3, WMA, or FLAC (lossless audio data compression format)
files stored in the computer (server) or NAS connected to the network. Browse the front panel display and select your
favorite music file.
To play back music files in your computer/NAS with this unit, you need to make the media sharing setting to computer/
NAS. For details on sharing setting, please refer to “SETUP OF YOUR NETWORK DEVICES” (p.12).
y
For details on playable music files, see “PLAYABLE DISCS AND FILE FORMATS” (☞ P.38).
2
Server
¡¡Pop/Rock
Use the following controls to select a
desired music file.
Main unit
1
2
OPERATIONS
Front panel display (example)
SELECT
ENTER
PUSH
The following icons are shown on the front panel display.
RETURN
Icon
Content
Displayed when a folder or music file can
be selected.
SELECT/ENTER
Displayed when a folder is selected.
1
Displayed when a supported music file is
selected.
SELECT/
ENTER
Displayed while a music file is being
played back.
RETURN
RETURN
Rotate
Selects a folder or music file.
Press
When a folder is selected:
moves down one level.
When a music file is selected:
starts playback.
Returns to the previous level.
Displayed while a music file is paused.
Remote control
2
Displayed when there is lower level in the
current folder.
HOME
REPEAT
A/B
SHUFFLE
POP-UP MENU
HOME
NOW PLAYING
NOW PLAYING
Operations from the main unit or
remote control
1
//ENTER
Press SOURCE repeatedly to switch the
audio source to “Server”.
ENTER
SETUP
RETURN
DISPLAY
OPTION
RETURN
Main unit/Remote control
OPEN/CLOSE
//
ENTER
DIMMER
SOURCE
/
Selects a folder or music file.
ENTER
When a folder is selected:
moves down one level.
When a music file is selected:
starts playback.
PURE DIRECT
SOURCE
2
3
4
5
6
RETURN
Returns to the previous level.
HOME
Moves to the top level.
NOW PLAYING
Stops browsing and displays
playback information for the
file currently being played.
PURE DIRECT
SOURCE
23 En
English
SOURCE
1
PLAYBACK OF MUSIC FILES ON YOUR PC/NAS
Remote control
3
When playback starts, use the following
controls to operate desired functions.
0
PROGRAM
CLEAR
REPEAT
A/B
SHUFFLE
POP-UP MENU
HOME
NOW PLAYING
REPEAT
Main unit
SHUFFLE
SELECT
ENTER
PUSH
RETURN
ENTER
SELECT/ENTER
RETURN
SETUP
RETURN
DISPLAY
OPTION
RETURN
Playback buttons
SELECT/
ENTER
Rotate
Skips to the next song, or back to
the previous song in the folder.
Press
Continues playback and returns
to display the folders or music
files that can be selected.
For details on selecting a folder
or music file, refer to step 2.
Continues playback and returns
to display the folders or music
files that can be selected.
For details on selecting a folder
or music file, refer to step 2.
RETURN
/
Playback
buttons
DISPLAY
Playback
buttons
Plays/Pauses.
Playback
buttons
/
/
Skips to the next song, or back to
the previous song in the folder.
RETURN
Continues playback and returns
to display the folders or music
files that can be selected.
For details on selecting a folder
or music file, refer to step 2.
Stops playback.
REPEAT
Skips to the next song, or back
to the previous song in the
folder.
Select the repeat playback method
(REPEAT ONE / REPEAT
ALL / REPEAT OFF).
SHUFFLE
Select the shuffle playback
method (SHUFFLE ALL /
SHUFFLE OFF).
DISPLAY
Changes the playback
information (Song name →
Artist name → Album title →
Playing time).
Plays/Pauses.
/
/
Stops playback.
y
You can also check the repeat/shuffle playback method from the
indicators on the front panel display (☞ P.8).
24 En
PLAYBACK OF INTERNET RADIO
You can listen to world-wide radio stations via Internet.
Make sure that the unit is connected to the Internet properly (☞ P.10).
Front panel display (Example)
1
NetRadio
¡¡Station¡List
Main unit/Remote control
2
The following icons are displayed on the front panel display.
Icon
OPEN/CLOSE
Content
SOURCE
Displayed when a folder is selected.
SOURCE
1
2
3
4
5
6
PURE DIRECT
Displayed when Internet radio station is
selected.
Displayed while a Internet radio station is
being played back.
2
PURE DIRECT
SOURCE
Displayed when a folder or Internet radio
station can be selected.
1
DIMMER
OPERATIONS
1
Press SOURCE repeatedly to switch the
audio source to “Net Radio”.
Displayed when there is lower level in the
current folder.
SOURCE
2
Selects an Internet radio station from the
folder, and press ENTER to start
playback.
y
When you select an internet radio station,
panel display.
appears on the front
Main unit
SELECT
ENTER
PUSH
RETURN
SELECT/ENTER
SELECT/
ENTER
RETURN
RETURN
Rotate
Selects a folder or Internet radio
station.
Press
When a folder is selected:
moves down one level.
When Internet radio station is
selected:
starts playback.
Returns to the previous level.
English
25 En
PLAYBACK OF INTERNET RADIO
Remote control
HOME
REPEAT
A/B
SHUFFLE
POP-UP MENU
HOME
NOW PLAYING
3
When playback starts, use the following
controls to operate desired functions.
NOW PLAYING
Main unit
//ENTER
ENTER
SELECT
ENTER
SETUP
RETURN
DISPLAY
OPTION
PUSH
RETURN
RETURN
//
ENTER
/
Selects a folder or Internet radio
station.
ENTER
When a folder is selected:
moves down one level.
When a Internet radio station is
selected:
starts playback.
RETURN
Returns to the previous level.
HOME
Moves to the top level.
NOW PLAYING
Stops browsing and displays
playback information for the
Internet radio station currently
being played.
Stops playback.
Remote control
ENTER
SETUP
RETURN
DISPLAY
OPTION
DISPLAY
Playback
buttons
Stops playback.
DISPLAY
Changes the playback
information (Station name →
Playing time → Song title).
y
You can register your favorite Internet radio stations to the
“Bookmarks” folder by selecting “Net Radio” as the source on
the unit and then accessing the following website with the web
browser on your PC.
http://yradio.vtuner.com/
Before registering an Internet radio station, play any Internet
radio station with this unit.
To use this feature, you need the vTuner ID of the unit and your
e-mail address to create your personal account.You can check the
vTuner ID (MAC address of the unit) in “Network Info”
(☞ P.29) in the Setup menu.
26 En
PLAYBACK OF AirPlay
The AirPlay function allows you to play back iPod/iTunes music on the unit wirelessly via a network.
Make sure that the unit and your PC or iPod are connected to the same network (☞ P.10).
Note
Playing iTunes
When you use iPod/iTunes controls to adjust volume, the volume
may be unexpectedly loud. This could result in damage to the unit
or speakers. If the volume increases during playback, stop
playback on iPod/iTunes immediately.
1
is shown on the
OPERATIONS
If the iTunes recognizes the unit,
screen of iTunes.
y
You can also use the unit and remote control to play back, pause,
stop, and skip songs.
Turn on the unit and start iTunes.
Example
Playing iPod
1
Turn on the unit and display the
playback screen on the iPod.
If the iPod recognizes the unit,
screen of the iPod.
is shown on the
2
Example on iOS6
and select the unit’s name.
The source automatically switches to “AirPlay”
(except when network standby is off).
y
For iPods using iOS 7, AirPlay is displayed in Control Center. To
access Control Center, swipe up from the bottom of the screen.
Click
Example
Example on iOS7
3
Play back songs with iTunes.
y
2
Tap
and select the unit’s name.
The source automatically switches to “AirPlay” and
playback starts.
To control iTunes playback with the remote control, you need to
configure the iTunes preferences to enable iTunes control from
remote speakers in advance.
Example of English version
Example
Clearing AirPlay
Tap/click
on the iPod/iTunes screen
and select a device other than CD-N301
from the speaker list. Or, change the
source to other than “AirPlay”.
27 En
English
1
SETUP MENU
You can configure the various settings of this unit using the setup menu.
2
Setup menu operations
Press / to select a menu item to
configure, then press ENTER.
For some menu items, repeat step 2 to select a
submenu item.
❚ Operations from the remote control
y
System
¡Net¡Standby
For details on the controls on the main unit or remote control, see
“CONTROLS AND FUNCTIONS” (☞ P.5).
1
Press SETUP to enter the setup menu
(☞ P.29).
To make the advanced setup menu
items (☞ P.29) selectable, press SETUP
while holding down RETURN (on the
main unit).
Remote control
PURE DIRECT
SOURCE
1
2
3
4
5
6
7
8
9
0
PROGRAM
CLEAR
REPEAT
A/B
SHUFFLE
POP-UP MENU
HOME
NOW PLAYING
Numeric
buttons
////
ENTER
ENTER
SETUP
RETURN
DISPLAY
OPTION
SETUP
RETURN
Main unit
SELECT
ENTER
PUSH
RETURN
RETURN
Front panel display
SETUP
¡System¡Config
28 En
3
Press / to select a parameter, then
press ENTER.
y
• You need to enter a numerical address for some menu items. In
this case, press / to move the target and / to select a
number, or use the numeric buttons. Then press ENTER to
confirm it.
• Press the RETURN button to return to the previous level.
SETUP MENU
Setup menu items
Menu
Submenu
Select “On” to enable the network standby mode.
AutoPowerStdby
20min*1,
This unit automatically enters standby mode if it is left turned
2hours, 4hours,
on for the selected time without playback or any other
8hours,
operation being performed.
12hours, Off*2
Accessory
On, Off
Selects whether or not to supply power to a Yamaha
accessory connected through the DC OUT jack.
Firm Version
The firmware version of this unit is shown.
Firm Update
Updates the firmware of the unit (☞ P.30).
Network Status
The network status of this unit is shown (“Connected” or
“Not connected”).
MAC Address
The MAC address of this unit is shown. The MAC address is
also used as a vTuner ID.
System ID
The system ID number is shown.
Network Name
Shows the name of the unit that appears on the network.
On, Off
OPERATIONS
On, Off
DHCP
Network Config
Function
Net Standby
System Config
Network Info
Settings
(Bold: default)
Select “On” to use the DHCP server to automatically
configure the network settings of this unit or “Off” to
configure manually.
IP Address
Specify the IP address when “DHCP” is “Off”. *3
Subnet Mask
Specify the subnet mask when “DHCP” is “Off”. *3
Def. Gateway
Specify the default gateway when “DHCP” is “Off”. *3
DNS Server (P)
Specify the primary DNS server when “DHCP” is “Off”. *3
DNS Server (S)
Specify the secondary DNS server when “DHCP” is “Off”. *3
*1 (U.K. model) Set to “20min” by default.
*2 (Australia model) Set to “Off” by default.
*3 When “DHCP” is “On”, you can check the values (IP address, etc.) assigned by the DHCP server.
Advanced setup menu
The following menu items are available only when you enter the setup menu by pressing SETUP (on the remote control)
while holding down RETURN (on the main unit).
Menu
MAC Filter
On, Off
Function
Select “On” to specify the MAC addresses (up to 5) of the network
components that will be permitted access to this unit (“Address1” to
“Address5”). Select “Off” to disable the MAC address filter function.
Reset the all settings of this unit to factory default. To reset the settings,
press SELECT/ENTER on the front panel or ENTER on the remote
control.
The reset operation will be reflected the next time you turn on this unit.
29 En
English
Initialize
Settings
(Bold: default)
SETUP MENU
Updating the firmware
When new firmware is released, a message to update your
current firmware will be shown on the front panel display
(when the unit is connected to the Internet only).
1
Press SETUP.
The setup menu is shown on the front panel display.
Remote control
POP-UP MENU
//ENTER
HOME
NOW PLAYING
ENTER
SETUP
RETURN
DISPLAY
OPTION
SETUP
2
Select “System Config” with / and
press ENTER.
3
Select “Firm Update” with / and
press ENTER.
4
Press ENTER again.
Update starts.
Network
S2:Writing¡56%
When update finishes, messages are shown in the
following order: “Update success.”, “Please…”, and
“power off!.”
5
Unplug the power cable from the wall
outlet and plug it back after about
30 seconds.
Update is applied.
Note
Do not operate the unit or disconnect the power cable and
network cables while updating.
y
• Once the message prompting update is shown on the front panel
display, it will not be shown again, even if you do not perform
updating. However, when you turn on the unit after the power
cable has been disconnected from the wall outlet for a while, the
message will be shown.
• When Internet speed is not fast enough or the unit is connected
to the wireless network via a wireless network adapter, network
update may not be possible depending on the condition of the
wireless connection. In this case, try again.
30 En
OTHERS
FREQUENTLY ASKED QUESTIONS
What kind of settings do I need to make?
→ For details on settings of your PC, NAS or mobile devices, see “SETUP OF YOUR NETWORK DEVICES”
(☞ P.12).
→ For details on the setup menu on this unit, see “SETUP MENU” (☞ P.28).
Why can’t I find music files on my PC?
→ Check the media sharing settings of your PC or media server, such as Windows Media Player 12 (☞ P.12).
→ Check if the music files are playable (☞ P.38).
Can I control this unit with my iPhone?
→ For details on controlling this unit from your mobile device, see “Operations from your mobile device” (☞ P.3).
OTHERS
I can’t find this unit using the dedicated application installed on my mobile device!
→ Check if this unit is properly connected to the same network via the broadband router.
→ Check if access to this unit is restricted by MAC address filter function (☞ P.33).
What music files are playable on this unit?
→ For details on playable files and formats, see “PLAYABLE DISCS AND FILE FORMATS” (☞ P.38).
How can I listen to Internet radio on this unit?
→ For details on listening to Internet radio stations, see “PLAYBACK OF INTERNET RADIO” (☞ P.25).
How do I play back my iPod/iTunes with AirPlay?
→ For details on playback, see “PLAYBACK OF AirPlay” (☞ P.27).
What do the messages on the front panel display stand for?
→ For details on the front panel display messages, see “Front panel display messages” (☞ P.36).
For latest information, please visit Yamaha website.
English
31 En
TROUBLESHOOTING
Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized
Yamaha dealer or service center.
❚ General
Problem
This unit fails to turn on.
The power indicator on the front
panel flashes.
This unit suddenly turns off.
No sound.
Cause
Remedy
Page
The power cable is not
connected to the AC IN socket
on the main unit or not plugged
into an AC outlet.
Connect the power cable firmly.
9
This unit has been exposed to a
strong external electric shock
(such as lightning or strong
static electricity).
Turn off this unit, disconnect
the power cable, plug it back in
after 30 seconds, then use it
normally.
—
The protection circuitry has
been activated three times
consecutively. When this unit is
in this condition, the power
indicator on the main unit blinks
if you try to turn on the power.
As a safety precaution,
capability to turn on the power
is disabled. Contact your nearest
Yamaha dealer or service center
to request repair.
—
There is a problem with the
internal circuitries of this unit.
Turn off this unit, disconnect
the power cable, then contact
the nearest authorized Yamaha
dealer or service center.
—
This unit entered standby mode.
This unit enters standby mode
after the time set for “Auto
Power Stdby” in the setup menu
has elapsed.
29
The audio cable connection
between this unit and amplifier
is improper.
Connect the audio cable firmly.
If the problem persists, use
another audio cable.
9
The input setting on the
amplifier is incorrect.
Select the correct input (from
this unit) on the amplifier.
—
The amplifier is not compatible
with the digital signals.
Use an analog signal
connection.
9
This unit is too close to the
digital or radio-frequency
equipment.
Move this unit away from such
equipment.
—
The audio cable between this
unit and the media sever is
defective.
Connect the audio cable firmly.
If the problem persists, use
another audio cable.
—
Noise is heard.
32 En
TROUBLESHOOTING
Problem
The remote control does not
work or function properly.
The amplifier control buttons on
the remote control do not work
on the amplifier.
Cause
Remedy
Page
Wrong distance or angle.
The remote control functions
within a maximum range of 6 m
(20 ft) and no more than 30
degrees off-axis from the front
panel of the main unit.
4
Direct sunlight or lighting is
striking the remote control
sensor of this unit.
Adjust the lighting angle, or
reposition this unit.
—
The batteries are weak.
Replace both batteries with new
ones.
4
Your amplifier is not one of
Yamaha amplifiers. (These
buttons may not work on some
Yamaha amplifiers.)
Use the remote control of your
amplifier.
—
❚ Network
The network feature does not
function.
Remedy
Page
The network parameters (IP
address) have not been obtained
properly.
Enable the DHCP server
function on the broadband
router and set “DHCP” in the
setup menu to “On” on this unit.
If you want to configure the
network parameters manually,
check that you are using an IP
address which is not used by
other network devices in your
network.
29
The media sharing setting is not
correct.
Configure the media sharing
setting of your PC.
12
Some security software installed
on your PC is blocking the
access of this unit to your PC.
Check the settings of security
software installed on your PC.
—
This unit and your PC are not in
the same network.
Check the network connections
and the broadband router
settings, then connect this unit
and your PC to the same
network.
10
Access to this unit is restricted
by MAC address filter function.
Disable MAC address filter
function in the setup menu of
this unit.
29
There are more than two routers
in use that are overlapping
among the network devices.
Disconnect the Internet
connection temporarily and
check via your local network, or
connect the network devices
you want to use to the same
router.
—
This unit does not detect the
digital media server (PC).
English
Cause
OTHERS
Problem
33 En
TROUBLESHOOTING
Problem
Cause
Remedy
Page
38
38
The files in your PC cannot be
viewed or played back.
The files are not supported by
this unit or the media server.
Use the file format supported by
both this unit and the media
server. For details on the
supported file formats by the
unit, see “PLAYABLE DISCS
AND FILE FORMATS”.
Some audio files cannot be
played back on this unit.
You are trying to play back
DRM audio files you purchased
on iTunes Store.
You cannot play back DRM
audio files you purchased on
iTunes Store.
❚ Internet radio
Problem
The Internet radio cannot be
played.
34 En
Cause
Remedy
Page
The selected Internet radio
station is currently not
available.
There may be a network
problem at the radio station, or
the service may have been
stopped. Try the station later or
select another station.
—
The selected Internet radio
station is currently broadcasting
silence.
Some Internet radio stations
broadcast silence at certain of
times of the day. Try the station
later or select another station.
—
Access to the network is
restricted by the firewall
settings of your network devices
(such as the broadband router).
Check the firewall settings of
your network devices. The
Internet radio can be played only
when it passes through the port
designated by each radio station.
The port number varies
depending on the radio station.
—
TROUBLESHOOTING
❚ CD
Problem
Page
A foreign object is obstructing
the tray.
Carefully check the disc tray and
remove the foreign object.
—
The disc is damaged.
Check the disc carefully and
replace it if necessary.
—
There is moisture on the laser
pickup.
Wait 20 to 30 minutes after
turning this unit on before trying
to play back a disc.
—
The disc is loaded upside down.
Reload the disc with the label
side up.
—
The disc is dirty.
Clean the disc.
38
The format of the MP3 or WMA
file is not compatible with this
unit.
Replace the disc with a correctly
recorded disc playable with this
unit.
38
The CD-RW (ReWritable) disc
is not recorded correctly.
Replace the disc with a correctly
recorded disc playable with this
unit.
38
The disc is a non-standard disc
not playable with this unit.
Replace the disc with a correctly
recorded disc playable with this
unit.
38
Playback is delayed, or begins
at the wrong place.
The disc is scratched or
damaged.
Check the disc carefully and
replace it if necessary.
38
Noise from inside of the disc tray.
The disc is warped.
Replace the disc.
—
Disc playback does not start.
Disc playback does not start.
OTHERS
Remedy
The disc tray does not close
completely.
Cause
English
35 En
TROUBLESHOOTING
Front panel display messages
Message
Status
Access error
There is a problem with the signal path from the network to the unit.
Connected
Connected to the network.
Initializing
Initializing the network settings.
Licensing err *
Access from the outside of the region for Pandora service.
List updated
The content list of the media server has been updated.
LOADING
The specified content is being loaded.
No content
This unit cannot find any content.
NO DISC
A CD is not inserted in the disc tray.
Not available
The operation you have performed is not available.
Not Connected
Cannot connect to the network.
Not signed in *
The unit is not signed in to the Pandora service.
OPEN
The CD tray is open.
Program Clear
The programmed track has been cleared.
Searching…
This unit is searching for content.
Suspended acct *
The Pandora service account is unusable.
Unknown DISC
An unsupported disc has been inserted.
Unsupported
Cannot play the specified contents.
* Australia model only
36 En
ADDITIONAL INFORMATION
This section describes about general ideas of DLNA (Digital Living Network Alliance) and NAS (Network Attached
Storage).
Internet
Modem
DLNA
SELECT
ENTER
PC
(Digital Media Server)
SOURCE
PUSH
PURE DIRECT
RETURN
Broadband
router
This unit (CD-N301)
(Digital Media Renderer)
OTHERS
Mobile device
(Digital Media Controller)
NAS
(Digital Media Server)
❚ DLNA
“DLNA” stands for Digital Living Network Alliance, and is a guideline to promote standardization of interconnection of
home network devices such as digital consumer electronics.
DLNA components are separated into four device classes: Digital Media Server (DMS), Digital Media Renderer (DMR),
Digital Media Player (DMP) and Digital Media Controller (DMC).
“Digital Media Server (DMS)” is a device that is used to store or distribute digital contents such as music files. For the
system using this unit, PCs and NAS are regarded as “Digital Media Server (DMS)”.
“Digital Media Controller (DMC)” is a device to control digital contents. The dedicated mobile device application
corresponds to “Digital Media Controller (DMC)” for the system using this unit.
“Digital Media Renderer (DMR)” is a device to receive instructions from “Digital Media Controller (DMC)” and play
back digital contents such as this unit.
Similarly, “Digital Media Player (DMP)” is a device that can play back digital contents stored on “Digital Media Server
(DMS)”.
❚ NAS
“NAS” stands for Network Attached Storage. By connecting your NAS and home network with a network cable directly,
NAS can be a storage device, such as a hard disc drive. If your NAS is compatible with DLNA, you can share your
music, pictures, or movies on the same home network as a digital media server.
English
37 En
PLAYABLE DISCS AND FILE FORMATS
Playable media and devices
❚ Supported PC
PC with Windows Media Player 11 or Windows Media
Player 12 installed.
❚ Supported NAS
Notes
• Do not use any nonstandard shaped disc
(heart, etc.) available on the market
because it might damage the unit.
• Do not use a disc with tape, stickers, or
paste on it. If you use such a disc, the
disc may get stuck in the unit, or damage
to the unit may result.
NAS that is compatible with DLNA version 1.5.
❚ About handling discs
❚ Supported mobile devices
• Always handle with care so that the playing surface is
not scratched. Do not warp discs.
For details, please visit Yamaha website.
❚ Playable discs
Use compact discs bearing the marks below.
Mark
Details
Compact discs (digital audio)
CD-R, CD-RW digital audio discs
• CD-R or CD-RW discs bearing one of
the following phrases.
FOR CONSUMER
FOR CONSUMER USE
FOR MUSIC USE ONLY
• Finalized CD-R or CD-RW discs only.
Note
This unit may not be able to play some CD-R/
CD-RW discs or discs on which recording
was not made correctly.
CD-TEXT discs
The disc title, artist name, and track
name are also displayed in addition to
the time displays when playing back a
CD with CD TEXT.
To play back an 8-cm (3-inch) CD
Place it in the inner recessed area of the disc tray. Do not
put a normal 12-cm (5-inch) CD on top of an 8-cm (3inch) CD.
38 En
• To keep clean the playing surface, wipe with a clean,
dry cloth. Do not use any type of disc cleaner, spray, or
any other chemical-based liquid.
• Do not wipe with a circular motion; wipe straight
outward from the center.
• Use a soft-tipped pen when writing on the label side of
the disc.
• When a disc is not being used, remove it from this unit
and store in an appropriate case.
• Do not expose discs to direct sunlight, high temperature
or high humidity for a long time.
Note
Do not use any lens cleaners as they may be a cause of
malfunction.
PLAYABLE DISCS AND FILE FORMATS
Playable discs and file formats
❚ DLNA
Sampling
frequency (kHz)
Quontization bit
WAV*1
8 to 192
16/24
MP3*2
8 to 48
16
WMA*3
8 to 48
16
AAC
8 to 48
16
FLAC
8 to 192
16/24
Formats
*1 Only Linear PCM format files are playable.
*2 MP3 PRO files are not supported.
*3 WMA PRO and Lossless files are not supported.
Sampling
frequency (kHz)
Quontization bit
MP3
8 to 48
16
WMA
16 to 48
16
Formats
OTHERS
❚ Discs
Notes
• Playback for MP3 or WMA files starts in alphanumeric order.
• Copyright-protected WMA (DRM) files cannot be played back
by this unit.
• The disc must be ISO 9660 compatible.
• Elapsed time may not be displayed correctly while playing back
variable bitrate contents.
English
39 En
SPECIFICATIONS
INPUT/OUTPUT
• NETWORK
Ethernet connection................................. 10Base-T/100Base-TX
Internet radio ........................................vTuner service supported
PC client function...................... DLNA Ver.1.5 (DMR function)
AirPlay ............................................................ AirPlay supported
• ANALOG OUT................................................................2ch (L/R)
• DIGITAL OUT
Optical ....................................................................................  1
Coaxial ...................................................................................  1
• DC OUT ....................................................................................  1
AUDIO SECTION
• Output level
1 kHz, 0 dB, fs 44.1 kHz............................................ 2.0 ± 0.3 V
• Signal to noise ratio (IHF-A network)
1 kHz, 0 dB, fs 44.1 kHz..................................... 110 dB or more
• Dynamic range
1 kHz, 0 dB, fs 44.1 kHz..................................... 100 dB or more
• Harmonic distortion
1 kHz, 0 dB, fs 44.1 kHz.......................................0.003% or less
• Frequency response
CD ............................................................ 2 Hz to 20 kHz, –3 dB
NETWORK
fs 48 kHz .................................................. 2 Hz to 24 kHz, –3 dB
fs 96 kHz .................................................. 2 Hz to 48 kHz, –3 dB
fs 192 kHz ................................................ 2 Hz to 96 kHz, –3 dB
GENERAL
• Power supply
[Australia model] ............................................. AC 240 V, 50 Hz
[U.K. model] .................................................... AC 230 V, 50 Hz
• Power consumption................................................................ 10 W
• Standby power consumption
Network standby On .......................................................... 2.5 W
Network standby Off.......................................................... 0.4 W
• Dimensions (W  H  D) .................................435  86  260 mm
• Weight ................................................................................... 3.2 kg
AirPlay works with iPhone, iPad, and iPod touch with
iOS 4.3.3 or later, Mac with OS X Mountain Lion, and
Mac and PC with iTunes 10.2.2 or later.
AirPlay, iPad, iPhone, iPod touch, iTunes and Retina
are trademarks of Apple Inc., registered in the U.S. and
other countries.
iPad Air and iPad mini are trademarks of Apple Inc.
Windows™
Windows is a registered trademark of Microsoft
Corporation in the United States and other countries.
Internet Explorer, Windows Media Audio and
Windows Media Player are either registered
trademarks or trademarks of Microsoft Corporation in
the United States and/or other countries.
Android™
Android and Google Play are trademarks of Google,
Inc.
This unit supports network connections.
* Please note that all specifications are subject to change without
notice.
DLNA™ and DLNA CERTIFIED™ are trademarks or
registered trademarks of Digital Living Network
Alliance. All rights reserved. Unauthorized use is
strictly prohibited.
MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
40 En
❚ Information about third party software licenses
This product incorporates the following third party software.
For information (copyright, etc) about each software, please read the terms and
conditions stated below.
By using this product, you will be deemed to have accepted the terms and conditions.
About ASN.1 object dumping code
ASN.1 object dumping code, copyright Peter Gutmann <pgut001@cs.auckland.ac.nz>,
based on ASN.1 dump program by David Kemp <dpkemp@missi.ncsc.mil>, with
contributions from various people including Matthew Hamrick <hamrick@rsa.com>,
Bruno Couillard <bcouillard@chrysalis-its.com>, Hallvard Furuseth
<h.b.furuseth@usit.uio.no>, Geoff Thorpe <geoff@raas.co.nz>, David Boyce
<d.boyce@isode.com>, John Hughes <john.hughes@entegrity.com>, Life is hard, and
then you die <ronald@trustpoint.com>, Hans-Olof Hermansson <hansolof.hermansson@postnet.se>, Tor Rustad <Tor.Rustad@bbs.no>, Kjetil Barvik
<kjetil.barvik@bbs.no>, James Sweeny <jsweeny@us.ibm.com>, and several other
people whose names I’ve misplaced.
This code grew slowly over time without much design or planning, with features being
tacked on as required.
It’s not representative of my normal coding style.
About FLAC codec Library
Copyright © 2000,2001,2002,2003,2004,2005,2006,2007,2008,2009 Josh Coalson
Redistribution and use in source and binary forms, with or without modification, are
permitted provided that the following conditions are met:
Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer.
Redistributions in binary form must reproduce the above copyright notice, this list of
conditions and the following disclaimer in the documentation and/or other materials
provided with the distribution.
Neither the name of the Xiph.org Foundation nor the names of its contributors may be
used to endorse or promote products derived from this software without specific prior
written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS ”AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
About libexpat
Copyright © 1998, 1999, 2000 Thai Open Source Software Center Ltd and Clark
Cooper
Copyright © 2001, 2002, 2003, 2004, 2005, 2006 Expat maintainers.
Permission is hereby granted, free of charge, to any person obtaining a copy of this
software and associated documentation files (the ”Software”), to deal in the Software
without restriction, including without limitation the rights to use, copy, modify, merge,
publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons
to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or
substantial portions of the Software.
THE SOFTWARE IS PROVIDED ”AS IS”, WITHOUT WARRANTY OF ANY
KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS
OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR
OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR
OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE
SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
About The Independent JPEG Group’s JPEG software
The Independent JPEG Group’s JPEG software
Copyright © 1991-2010, Thomas G. Lane, Guido Vollbeding.
All Rights Reserved except as specified below.
The authors make NO WARRANTY or representation, either express or implied, with
respect to this software, its quality, accuracy, merchantability, or fitness for a particular
purpose. This software is provided ”AS IS”, and you, its user, assume the entire risk as
to its quality and accuracy.
Permission is hereby granted to use, copy, modify, and distribute this software (or
portions thereof) for any purpose, without fee, subject to these conditions:
(1) If any part of the source code for this software is distributed, then this README
file must be included, with this copyright and no-warranty notice unaltered; and any
additions, deletions, or changes to the original files must be clearly indicated in
accompanying documentation.
(2) If only executable code is distributed, then the accompanying documentation must
state that ”this software is based in part on the work of the Independent JPEG
Group”.
(3) Permission for use of this software is granted only if the user accepts full
responsibility for any undesirable consequences; the authors accept NO
LIABILITY for damages of any kind.
These conditions apply to any software derived from or based on the IJG code, not just
to the unmodified library. If you use our work, you ought to acknowledge us.
Permission is NOT granted for the use of any IJG author’s name or company name in
advertising or publicity relating to this software or products derived from it. This
software may be referred to only as ”the Independent JPEG Group’s software”.
We specifically permit and encourage the use of this software as the basis of
commercial products, provided that all warranty or liability claims are assumed by the
product vendor.
About JsonCpp
Copyright © 2007-2010 Baptiste Lepilleur
Permission is hereby granted, free of charge, to any person obtaining a copy of this
software and associated documentation files (the ”Software”), to deal in the Software
without restriction, including without limitation the rights to use, copy, modify, merge,
publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons
to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or
substantial portions of the Software.
THE SOFTWARE IS PROVIDED ”AS IS”, WITHOUT WARRANTY OF ANY
KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS
OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR
OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR
OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE
SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
About Network
Copyright © 1988 Stephen Deering.
Copyright © 1992, 1993
The Regents of the University of California. All rights reserved.
Copyright © 1985, 1986, 1993
The Regents of the University of California. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are
permitted provided that the following conditions are met:
(1) Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer.
(2) Redistributions in binary form must reproduce the above copyright notice, this list
of conditions and the following disclaimer in the documentation and/or other
materials provided with the distribution.
(3) All advertising materials mentioning features or use of this software must display
the following acknowledgement:
This product includes software developed by the University of California, Berkeley
and its contributors.
(4) Neither the name of the University nor the names of its contributors may be used to
endorse or promote products derived from this software without specific prior
written permission.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ”AS
IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT
SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF
THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGE.
Copyright © 1982, 1986 Regents of the University of California.
All rights reserved.
Copyright © 1982, 1986, 1988 Regents of the University of California.
All rights reserved.
Redistribution and use in source and binary forms are permitted provided that the above
copyright notice and this paragraph are duplicated in all such forms and that any
documentation, advertising materials, and other materials related to such distribution
and use acknowledge that the software was developed by the University of California,
Berkeley. The name of the University may not be used to endorse or promote products
derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED ”AS IS” AND WITHOUT ANY EXPRESS OR
IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR
PURPOSE.
About PNG Reference Library
ibpng versions 1.2.6, August 15, 2004, through 1.4.5, December 9, 2010, are Copyright
© 2004, 2006-2010 Glenn Randers-Pehrson, and are distributed according to the same
i
disclaimer and license as libpng-1.2.5 with the following individual added to the list of
Contributing Authors
Cosmin Truta
libpng versions 1.0.7, July 1, 2000, through 1.2.5 - October 3, 2002, are Copyright ©
2000-2002 Glenn Randers-Pehrson, and are distributed according to the same
disclaimer and license as libpng-1.0.6 with the following individuals added to the list of
Contributing Authors
Simon-Pierre Cadieux
Eric S. Raymond
Gilles Vollant
and with the following additions to the disclaimer:
There is no warranty against interference with your enjoyment of the library or
against infringement. There is no warranty that our efforts or the library will fulfill
any of your particular purposes or needs. This library is provided with all faults, and
the entire risk of satisfactory quality, performance, accuracy, and effort is with the
user.
libpng versions 0.97, January 1998, through 1.0.6, March 20, 2000, are Copyright ©
1998, 1999 Glenn Randers-Pehrson, and are distributed according to the same
disclaimer and license as libpng-0.96, with the following individuals added to the list of
Contributing Authors:
Tom Lane
Glenn Randers-Pehrson
Willem van Schaik
libpng versions 0.89, June 1996, through 0.96, May 1997, are Copyright © 1996, 1997
Andreas Dilger
Distributed according to the same disclaimer and license as libpng-0.88, with the
following individuals added to the list of Contributing Authors:
John Bowler
Kevin Bracey
Sam Bushell
Magnus Holmgren
Greg Roelofs
Tom Tanner
libpng versions 0.5, May 1995, through 0.88, January 1996, are Copyright © 1995,
1996 Guy Eric Schalnat, Group 42, Inc.
For the purposes of this copyright and license, ”Contributing Authors” is defined as the
following set of individuals:
Andreas Dilger
Dave Martindale
Guy Eric Schalnat
(3) Neither the name(s) of the above-listed copyright holder(s) nor the names of its
contributors may be used to endorse or promote products derived from this software
without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS ”AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
About zlib Library
Copyright notice:
© 1995-2010 Jean-loup Gailly and Mark Adler
This software is provided ‘as-is’, without any express or implied warranty. In no event
will the authors be held liable for any damages arising from the use of this software.
Permission is granted to anyone to use this software for any purpose, including
commercial applications, and to alter it and redistribute it freely, subject to the
following restrictions:
(1) The origin of this software must not be misrepresented; you must not claim that you
wrote the original software. If you use this software in a product, an
acknowledgment in the product documentation would be appreciated but is not
required.
(2) Altered source versions must be plainly marked as such, and must not be
misrepresented as being the original software.
(3) This notice may not be removed or altered from any source distribution.
About Apple Lossless Audio Codec
Copyright © 2011 Apple Inc. All rights reserved.
Licensed under the Apache License, Version 2.0
(the ”License”); you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software distributed under the
License is distributed on an ”AS IS” BASIS, WITHOUT WARRANTIES OR
CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and limitations under
the License.
Boost
The PNG Reference Library is supplied ”AS IS”. The Contributing Authors and Group
42, Inc. disclaim all warranties, expressed or implied, including, without limitation, the
warranties of merchantability and of fitness for any purpose. The Contributing Authors
and Group 42, Inc. assume no liability for direct, indirect, incidental, special,
exemplary, or consequential damages, which may result from the use of the PNG
Reference Library, even if advised of the possibility of such damage.
Permission is hereby granted to use, copy, modify, and distribute this source code, or
portions hereof, for any purpose, without fee, subject to the following restrictions:
(1) The origin of this source code must not be misrepresented.
(2) Altered versions must be plainly marked as such and must not be misrepresented as
being the original source.
(3) This Copyright notice may not be removed or altered from any source or altered
source distribution.
The Contributing Authors and Group 42, Inc. specifically permit, without fee, and
encourage the use of this source code as a component to supporting the PNG file format
in commercial products. If you use this source code in a product, acknowledgment is
not required but would be appreciated.
http://www.boost.org/
Boost Software License - Version 1.0 - August 17th, 2003
Permission is hereby granted, free of charge, to any person or organization obtaining a
copy of the software and accompanying documentation covered by this license (the
”Software”) to use, reproduce, display, distribute, execute, and transmit the Software,
and to prepare derivative works of the Software, and to permit third-parties to whom the
Software is furnished to do so, all subject to the following:
The copyright notices in the Software and this entire statement, including the above
license grant, this restriction and the following disclaimer, must be included in all
copies of the Software, in whole or in part, and all derivative works of the Software,
unless such copies or derivative works are solely in the form of machine-executable
object code generated by a source language processor.
THE SOFTWARE IS PROVIDED ”AS IS”, WITHOUT WARRANTY OF ANY
KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, TITLE AND NON-INFRINGEMENT. IN NO EVENT SHALL THE
COPYRIGHT HOLDERS OR ANYONE DISTRIBUTING THE SOFTWARE BE
LIABLE FOR ANY DAMAGES OR OTHER LIABILITY, WHETHER IN
CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
THE SOFTWARE.
About RC4 Algorithm
Expat
Copyright Mocana Corp 2003-2005. All Rights Reserved.
Proprietary and Confidential Material.
http://www.jclark.com/xml/expat.html
Expat License. Copyright © 1998, 1999, 2000 Thai Open Source Software Center Ltd
Permission is hereby granted, free of charge, to any person obtaining a copy of this
software and associated documentation files (the ”Software”), to deal in the Software
without restriction, including without limitation the rights to use, copy, modify, merge,
publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons
to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or
substantial portions of the Software.
THE SOFTWARE IS PROVIDED ”AS IS”, WITHOUT WARRANTY OF ANY
KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS
OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR
Paul Schmidt
Tim Wegner
About WPA Supplicant
Copyright © 2003-2008, Jouni Malinen <j@w1.fi> and contributors
All Rights Reserved.
Redistribution and use in source and binary forms, with or without modification, are
permitted provided that the following conditions are met:
(1) Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer.
(2) Redistributions in binary form must reproduce the above copyright notice, this list
of conditions and the following disclaimer in the documentation and/or other
materials provided with the distribution.
ii
OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR
OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE
SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
FastDelegate
http://www.codeproject.com/KB/cpp/FastDelegate.aspx
THE WORK (AS DEFINED BELOW) IS PROVIDED UNDER THE TERMS OF
THIS CODE PROJECT OPEN LICENSE (”LICENSE”). THE WORK IS
PROTECTED BY COPYRIGHT AND/OR OTHER APPLICABLE LAW. ANY USE
OF THE WORK OTHER THAN AS AUTHORIZED UNDER THIS LICENSE OR
COPYRIGHT LAW IS PROHIBITED.
BY EXERCISING ANY RIGHTS TO THE WORK PROVIDED HEREIN, YOU
ACCEPT AND AGREE TO BE BOUND BY THE TERMS OF THIS LICENSE. THE
AUTHOR GRANTS YOU THE RIGHTS CONTAINED HEREIN IN
CONSIDERATION OF YOUR ACCEPTANCE OF SUCH TERMS AND
CONDITIONS. IF YOU DO NOT AGREE TO ACCEPT AND BE BOUND BY THE
TERMS OF THIS LICENSE, YOU CANNOT MAKE ANY USE OF THE WORK.
1. Definitions.
a. ”Articles” means, collectively, all articles written by Author which describes
how the Source Code and Executable Files for the Work may be used by a user.
b. ”Author” means the individual or entity that offers the Work under the terms of
this License.
c. ”Derivative Work” means a work based upon the Work or upon the Work and
other pre-existing works.
d. ”Executable Files” refer to the executables, binary files, configuration and any
required data files included in the Work.
e. ”Publisher” means the provider of the website, magazine, CD-ROM, DVD or
other medium from or by which the Work is obtained by You.
f. ”Source Code” refers to the collection of source code and configuration files
used to create the Executable Files.
g. ”Standard Version” refers to such a Work if it has not been modified, or has been
modified in accordance with the consent of the Author, such consent being in the
full discretion of the Author.
h. ”Work” refers to the collection of files distributed by the Publisher, including the
Source Code, Executable Files, binaries, data files, documentation, whitepapers
and the Articles.
i. ”You” is you, an individual or entity wishing to use the Work and exercise your
rights under this License.
2. Fair Use/Fair Use Rights. Nothing in this License is intended to reduce, limit, or
restrict any rights arising from fair use, fair dealing, first sale or other limitations on
the exclusive rights of the copyright owner under copyright law or other applicable
laws.
3. License Grant. Subject to the terms and conditions of this License, the Author
hereby grants You a worldwide, royalty-free, non-exclusive, perpetual (for the
duration of the applicable copyright) license to exercise the rights in the Work as
stated below:
a. You may use the standard version of the Source Code or Executable Files in
Your own applications.
b. You may apply bug fixes, portability fixes and other modifications obtained from
the Public Domain or from the Author. A Work modified in such a way shall still
be considered the standard version and will be subject to this License.
c. You may otherwise modify Your copy of this Work (excluding the Articles) in
any way to create a Derivative Work, provided that You insert a prominent notice
in each changed file stating how, when and where You changed that file.
d. You may distribute the standard version of the Executable Files and Source Code
or Derivative Work in aggregate with other (possibly commercial) programs as
part of a larger (possibly commercial) software distribution.
e. The Articles discussing the Work published in any form by the author may not
be distributed or republished without the Author’s consent. The author retains
copyright to any such Articles. You may use the Executable Files and Source
Code pursuant to this License but you may not repost or republish or otherwise
distribute or make available the Articles, without the prior written consent of the
Author.
Any subroutines or modules supplied by You and linked into the Source Code or
Executable Files this Work shall not be considered part of this Work and will not be
subject to the terms of this License.
4. Patent License. Subject to the terms and conditions of this License, each Author
hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free,
irrevocable (except as stated in this section) patent license to make, have made, use,
import, and otherwise transfer the Work.
5. Restrictions. The license granted in Section 3 above is expressly made subject to
and limited by the following restrictions:
a. You agree not to remove any of the original copyright, patent, trademark, and
attribution notices and associated disclaimers that may appear in the Source
Code or Executable Files.
b. You agree not to advertise or in any way imply that this Work is a product of
Your own.
c. The name of the Author may not be used to endorse or promote products derived
from the Work without the prior written consent of the Author.
d. You agree not to sell, lease, or rent any part of the Work. This does not restrict
you from including the Work or any part of the Work inside a larger software
distribution that itself is being sold. The Work by itself, though, cannot be sold,
leased or rented.
e. You may distribute the Executable Files and Source Code only under the terms
of this License, and You must include a copy of, or the Uniform Resource
Identifier for, this License with every copy of the Executable Files or Source
Code You distribute and ensure that anyone receiving such Executable Files and
Source Code agrees that the terms of this License apply to such Executable Files
and/or Source Code. You may not offer or impose any terms on the Work that
alter or restrict the terms of this License or the recipients’ exercise of the rights
granted hereunder. You may not sublicense the Work. You must keep intact all
notices that refer to this License and to the disclaimer of warranties. You may
not distribute the Executable Files or Source Code with any technological
measures that control access or use of the Work in a manner inconsistent with
the terms of this License.
f. You agree not to use the Work for illegal, immoral or improper purposes, or on
pages containing illegal, immoral or improper material. The Work is subject to
applicable export laws. You agree to comply with all such laws and regulations
that may apply to the Work after Your receipt of the Work.
6. Representations, Warranties and Disclaimer. THIS WORK IS PROVIDED ”AS IS”,
”WHERE IS” AND ”AS AVAILABLE”, WITHOUT ANY EXPRESS OR
IMPLIED WARRANTIES OR CONDITIONS OR GUARANTEES. YOU, THE
USER, ASSUME ALL RISK IN ITS USE, INCLUDING COPYRIGHT
INFRINGEMENT, PATENT INFRINGEMENT, SUITABILITY, ETC. AUTHOR
EXPRESSLY DISCLAIMS ALL EXPRESS, IMPLIED OR STATUTORY
WARRANTIES OR CONDITIONS, INCLUDING WITHOUT LIMITATION,
WARRANTIES OR CONDITIONS OF MERCHANTABILITY,
MERCHANTABLE QUALITY OR FITNESS FOR A PARTICULAR PURPOSE,
OR ANY WARRANTY OF TITLE OR NON-INFRINGEMENT, OR THAT THE
WORK (OR ANY PORTION THEREOF) IS CORRECT, USEFUL, BUG-FREE
OR FREE OF VIRUSES. YOU MUST PASS THIS DISCLAIMER ON
WHENEVER YOU DISTRIBUTE THE WORK OR DERIVATIVE WORKS.
7. Indemnity. You agree to defend, indemnify and hold harmless the Author and the
Publisher from and against any claims, suits, losses, damages, liabilities, costs, and
expenses (including reasonable legal or attorneys’ fees) resulting from or relating to
any use of the Work by You.
8. Limitation on Liability. EXCEPT TO THE EXTENT REQUIRED BY
APPLICABLE LAW, IN NO EVENT WILL THE AUTHOR OR THE
PUBLISHER BE LIABLE TO YOU ON ANY LEGAL THEORY FOR ANY
SPECIAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY
DAMAGES ARISING OUT OF THIS LICENSE OR THE USE OF THE WORK
OR OTHERWISE, EVEN IF THE AUTHOR OR THE PUBLISHER HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
9. Termination.
a. This License and the rights granted hereunder will terminate automatically upon
any breach by You of any term of this License. Individuals or entities who have
received Derivative Works from You under this License, however, will not have
their licenses terminated provided such individuals or entities remain in full
compliance with those licenses. Sections 1, 2, 6, 7, 8, 9, 10 and 11 will survive
any termination of this License.
b. If You bring a copyright, trademark, patent or any other infringement claim
against any contributor over infringements You claim are made by the Work,
your License from such contributor to the Work ends automatically.
c. Subject to the above terms and conditions, this License is perpetual (for the
duration of the applicable copyright in the Work). Notwithstanding the above,
the Author reserves the right to release the Work under different license terms or
to stop distributing the Work at any time; provided, however that any such
election will not serve to withdraw this License (or any other license that has
been, or is required to be, granted under the terms of this License), and this
License will continue in full force and effect unless terminated as stated above.
10. Publisher. The parties hereby confirm that the Publisher shall not, under any
circumstances, be responsible for and shall not have any liability in respect of the
subject matter of this License. The Publisher makes no warranty whatsoever in
connection with the Work and shall not be liable to You or any party on any legal
theory for any damages whatsoever, including without limitation any general,
special, incidental or consequential damages arising in connection to this license.
The Publisher reserves the right to cease making the Work available to You at any
time without notice
11. Miscellaneous.
a. This License shall be governed by the laws of the location of the head office of
the Author or if the Author is an individual, the laws of location of the principal
place of residence of the Author.
b. If any provision of this License is invalid or unenforceable under applicable law,
it shall not affect the validity or enforceability of the remainder of the terms of
this License, and without further action by the parties to this License, such
provision shall be reformed to the minimum extent necessary to make such
provision valid and enforceable.
c. No term or provision of this License shall be deemed waived and no breach
consented to unless such waiver or consent shall be in writing and signed by the
party to be charged with such waiver or consent.
d. This License constitutes the entire agreement between the parties with respect to
the Work licensed herein. There are no understandings, agreements or
representations with respect to the Work not specified herein. The Author shall
not be bound by any additional provisions that may appear in any
communication from You. This License may not be modified without the mutual
written agreement of the Author and You
libogg
http://www.xiph.org/ogg/
Copyright © 2002, Xiph.org Foundation
iii
Redistribution and use in source and binary forms, with or without modification, are
permitted provided that the following conditions are met:
• Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer.
• Redistributions in binary form must reproduce the above copyright notice, this list of
conditions and the following disclaimer in the documentation and/or other materials
provided with the distribution.
• Neither the name of the Xiph.org Foundation nor the names of its contributors may
be used to endorse or promote products derived from this software without specific
prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS ”AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
libvorbis
http://www.xiph.org/vorbis/
Copyright © 2002-2004 Xiph.org Foundation
Redistribution and use in source and binary forms, with or without modification, are
permitted provided that the following conditions are met:
• Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer.
• Redistributions in binary form must reproduce the above copyright notice, this list of
conditions and the following disclaimer in the documentation and/or other materials
provided with the distribution.
• Neither the name of the Xiph.org Foundation nor the names of its contributors may
be used to endorse or promote products derived from this software without specific
prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS ”AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Tremolo
http://wss.co.uk/pinknoise/tremolo
Copyright © 2002-2009 Xiph.org Foundation Changes Copyright © 2009-2010 Robin
Watts for Pinknoise Productions Ltd
Redistribution and use in source and binary forms, with or without modification, are
permitted provided that the following conditions are met:
– Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer.
– Redistributions in binary form must reproduce the above copyright notice, this list of
conditions and the following disclaimer in the documentation and/or other materials
provided with the distribution.
– Neither the name of the Xiph.org Foundation nor the names of its contributors may
be used to endorse or promote products derived from this software without specific
prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS ”AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGE.
Tremor
http://wiki.xiph.org/index.php/Tremor
Copyright © 2002, Xiph.org Foundation
Redistribution and use in source and binary forms, with or without modification, are
permitted provided that the following conditions are met:
– Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer.
iv
– Redistributions in binary form must reproduce the above copyright notice, this list of
conditions and the following disclaimer in the documentation and/or other materials
provided with the distribution.
– Neither the name of the Xiph.org Foundation nor the names of its contributors may
be used to endorse or promote products derived from this software without specific
prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS ”AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Mersenne Twister
http://www.math.sci.hiroshima-u.ac.jp/~m-mat/MT/MT2002/CODES/mt19937ar.c
Copyright © 1997 - 2002, Makoto Matsumoto and Takuji Nishimura,
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are
permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list
of conditions and the following disclaimer in the documentation and/or other
materials provided with the distribution.
3. The names of its contributors may not be used to endorse or promote products
derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS ”AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
zlib
http://www.zlib.net/
zlib.h -- interface of the ‘zlib’ general purpose compression library version 1.2.3, July
18th, 2005
Copyright © 1995-2004 Jean-loup Gailly and Mark Adler
This software is provided ‘as-is’, without any express or implied warranty. In no event
will the authors be held liable for any damages arising from the use of this software.
Permission is granted to anyone to use this software for any purpose, including
commercial applications, and to alter it and redistribute it freely, subject to the
following restrictions:
The origin of this software must not be misrepresented; you must not claim that you
wrote the original software. If you use this software in a product, an acknowledgment in
the product documentation would be appreciated but is not required.
1. Altered source versions must be plainly marked as such, and must not be
misrepresented as being the original software.
2. This notice may not be removed or altered from any source distribution.
Jean-loup Gailly jloup@gzip.org, Mark Adler madler@alumni.caltech.edu
cURL
http://curl.haxx.se
COPYRIGHT AND PERMISSION NOTICE
Copyright © 1996 - 2011, Daniel Stenberg, <daniel@haxx.se>.
All rights reserved.
Permission to use, copy, modify, and distribute this software for any purpose with or
without fee is hereby granted, provided that the above copyright notice and this
permission notice appear in all copies.
THE SOFTWARE IS PROVIDED ”AS IS”, WITHOUT WARRANTY OF ANY
KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN NO
EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR
ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION
OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
THE SOFTWARE.
Except as contained in this notice, the name of a copyright holder shall not be used in
advertising or otherwise to promote the sale, use or other dealings in this Software
without prior written authorization of the copyright holder.
c-ares
http://c-ares.haxx.se
Copyright 1998 by the Massachusetts Institute of Technology.
Permission to use, copy, modify, and distribute this software and its documentation for
any purpose and without fee is hereby granted, provided that the above copyright notice
appear in all copies and that both that copyright notice and this permission notice
appear in supporting documentation, and that the name of M.I.T. not be used in
advertising or publicity pertaining to distribution of the software without specific,
written prior permission. M.I.T. makes no representations about the suitability of this
software for any purpose. It is provided ”as is” without express or implied warranty.
Do not disassemble, decompile, or reverse engineer the software included in
Yamaha AV products.
v
English
Information for Users on Collection and Disposal of Old Equipment
and Used Batteries
These symbols on the products, packaging, and/or accompanying documents mean that used electrical and
electronic products and batteries should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them to
applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC
and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources and prevent
any potential negative effects on human health and the environment which could otherwise arise from
inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please contact your local
municipality, your waste disposal service or the point of sale where you purchased the items.
[Information on Disposal in other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to discard these items, please contact your
local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with the
requirement set by the Directive for the chemical involved.
vi
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
The laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
LASER SAFETY
This unit employs a laser. Due to possible eye injury, only a
qualified service person should remove the cover or attempt to
service this device.
DANGER
This unit emits visible laser radiation when open. Avoid direct
eye exposure to beam. When this unit is plugged into the wall
outlet, do not place your eyes close to the opening of the disc tray
and other openings to look into inside.
LASER
Type
Wave length
Output Power
Semiconductor laser GaAs/GaAlAs
790 nm
10 mW
■ For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the instructions
described below.
Note
The plug severed from the mains lead must be destroyed, as a
plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
■ Special Instructions for U.K. Model
DANGER - VISIBLE AND INVISIBLE RADIATION WHEN OPEN.
AVOID DIRECT EXPOSURE TO BEAM.
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured
BLACK. The wire which is coloured BROWN must be
connected to the terminal which is marked with the letter L
or coloured RED.
Make sure that neither core is connected to the earth
terminal of the three pin plug.
CAUTION - CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM.
VARNING - KLASS 3B SYNLIG OCH OSYNLIG LASERSTRÅLNING
NÄR DENNA DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.
VARO !
AVATTAESSA OLET ALTTINA LUOKAN 3B NÄKYVÄLLE JA
NÄKYMÄTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING - KLASS 3B SYNLIG OCH OSYNLIG LASERSTRÅLNING
NÄR DENNA DEL ÄR ÖPPNAD. BETRAKTÅ EJ STRALEN.
VORSICHT ! SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG KLASSE 3B
WENN ABDECKUNG GEÖFFNET. NICHT DEM STRAHL AUSSETZEN.
ATTENTION - RADIATION VISIBLE ET INVISIBLE CLASSE 3B LORSQUE L’APPAREIL
EST OUVERT. EVITEZ TOUTE EXPOSITION AU FAISCEAU.
vii
© 2014 Yamaha Corporation
Printed in Malaysia ZN17920-1