Zhone ENE2000-P Instruction manual

SNE2040G-P and SNE2040G-S
4-Port Network Extenders
Installation Instructions
Document Number SNE2-A2-ZN12-30
October 2005
Contents
End User License Agreement (Zhone and Affiliates) ...............................................................
Product Documentation Online .................................................................................................
Package Contents ......................................................................................................................
Connecting to Power .................................................................................................................
Switchpack Configuration (SNE2040G-P) ...............................................................................
Connecting the SHDSL Lines ...................................................................................................
SHDSL RJ45 Connector Pinouts ..............................................................................................
Connecting the Ethernet Line ....................................................................................................
10/100 Ethernet RJ45 Pinouts ...................................................................................................
LED Indicators ..........................................................................................................................
EMI Notices ..............................................................................................................................
ACTA Customer Information ....................................................................................................
Supplier's Declaration of Conformity .......................................................................................
Notice to Users of the Canadian Telephone Network ...............................................................
CE Marking ...............................................................................................................................
Japan Notice ..............................................................................................................................
Important Safety Instructions ....................................................................................................
Contacting Global Service and Support ....................................................................................
Technical Support ......................................................................................................................
Service Requirements ................................................................................................................
SNE2-A2-ZN12-30
2
3
3
4
5
6
7
8
8
9
11
11
12
12
13
13
14
15
15
15
1
End User License Agreement (Zhone
and Affiliates)
Do not install this Software unless you agree to these provisions.
Return the Software promptly for a refund if you do not agree.
License. Zhone Technologies, Inc. and/or an affiliate ("Zhone") hereby grants you
("User")—either an individual or a single business entity—the non-exclusive right to install,
access, run, or interact with ("Use") one copy of the enclosed software (which may have been, or
may be, provided on media, as part of a hardware platform, through download, or otherwise) and
associated documentation ("Software") on the first computer system on which User installs the
Software ("System") solely for internal business purposes (including, without limitation,
providing products and services to User's customers) and subject to the restrictions below).
Zhone may, in its sole discretion, make available future updates or upgrades to the Software each
of which is also Software subject hereto. Title to and all patent rights, copyrights and other
intellectual property rights in the Software are retained by Zhone and its direct and indirect
suppliers and licensors ("Licensors").
Restrictions. The Software may not be (a) Used on or from any system other than the System; (b)
Used with more than any maximum number of subscribers stated in the documentation
accompanying the Software; (c) Used so as to circumvent any technological measure included
therein or provided by Zhone from time to time to control access to or limit use of the Software;
(d) sublicensed, rented, leased or lent to third parties; (e) imported or exported into any
jurisdiction except in compliance with all applicable laws of the United States and such
jurisdiction; (f) transferred to a third party unless (A) User transfers the original and all surviving
copies to a third party who has agreed in writing to be bound hereby and (B) such third party pays
to Zhone such reasonable additional fee as Zhone may impose from time to time with respect to
such transfer; or (g) made available to third parties as part of any time-sharing or service bureau
arrangement. User shall not have the right to use the Software or any portion thereof for a use
other than that contemplated by its documentation. User will not copy all or any part of the
Software or attempt, or encourage or permit any third party, to modify, adapt, make derivative
works from, reverse engineer, reverse compile, disassemble or decompile the Software or any
portion thereof except and only to the extent that such activity is expressly permitted by law
notwithstanding this limitation. Violation of any of the foregoing shall be deemed a material
breach hereof. User may make a reasonable number of copies solely for archival or disaster
recovery and subject to the restrictions imposed by copyright law, but may not modify or
otherwise copy the Software. User agrees to reproduce product identification, copyright and
other proprietary notices of Zhone and Licensors on all copies. User's rights are only as expressly
stated herein. Zhone may immediately terminate your rights if you violate the provisions hereof.
Limited Warranty. Zhone warrants that the media containing the Software is free from defects in
material and workmanship for ninety (90) days following your purchase of the Software. You
may provide written notice of such defect (addressed to Zhone Technologies, Inc., Attention:
Customer Service, 7001 Oakport Street @ Zhone Way, Oakland, CA 94621) no later than ten
(10) days following expiration of such period and, as your sole and exclusive remedy, Zhone will
provide replacement media. NEITHER ZHONE NOR ITS LICENSORS MAKE ANY OTHER
WARRANTY, EXPRESS, IMPLIED OR STATUTORY. ZHONE AND ITS LICENSORS
2
SNE2-A2-ZN12-30
DISCLAIM ALL WARRANTIES OF FITNESS FOR PARTICULAR PURPOSE,
MERCHANTABILITY AND NON-INFRINGEMENT. Some states or other jurisdictions do not
allow the exclusion of implied warranties on limitations on how long an implied warranty lasts,
so the above limitations may not apply to you. This warranty gives you specific legal rights, and
you may also have other rights which vary from one state or jurisdiction to another.
Limit of Liability. In case of any claim hereunder or related to the Software, neither Zhone nor its
Licensors shall be liable for direct damages exceeding the price paid by User for the Software or
for special, incidental, consequential or indirect damages, even if advised in advance of the
potential thereof.
U.S. Government Users. The Software is a "commercial item" as defined at 48 C.F.R. 2.101,
consisting of "commercial computer software" and "commercial computer software
documentation" as such terms are used in 48 C.F.R. 12.212. Under 48 C.F.R. 12.212 and 48
C.F.R. 227.7202-1 to 227.7202-4, U.S. Government Users acquire the Software only with the
rights set forth therein.
Third Party Licensors. This Zhone End User License Agreement may be accompanied by
differing or additional provisions applicable to portions of the Software provided by one or more
Licensors ("Licensor Provisions"). User acknowledges and agrees that its Use of such portions of
the Software is subject to the Licensor Provisions.
Product Documentation Online
This document describes units manufactured after July 2004. See the prior version of this
document for information about units manufactured earlier.
Complete documentation for Zhone network extenders and related products is available at
www.zhone.com.
Package Contents
Unpack and Inspect the Equipment. The following components should be included:
z
1 SNE2040G
z
1 Power supply
If there is any visible damage, do not attempt to connect the device. Contact your sales or service
provider.
SNE2-A2-ZN12-30
3
Connecting to Power
Plug the power supply into the Power Adapter port on the back of the SNE2040G and connect it
to your power source. Verify that the Power LED on the front of the SNE2040G is illuminated.
SDSL Network Extender 2000
SNE2040G
Lnk
Tx
Rx
1 2 3 4
SDSL Connection
Power
Power Adapter
100
Act
Lnk
10/100 Ethernet Connection
1
2
3
4
1 2 3 4 5 67 8
10/100 Ethernet
5V DC
Configuration
SDSL
04-17574
Upon start up, the Ethernet link will remain disabled (as indicated by no illumination of the
Ethernet Rx, Tx, and Lnk LEDs) until at least one of the SHDSL connections has been
established.
4
SNE2-A2-ZN12-30
Switchpack Configuration (SNE2040G-P)
Configuration switches for the G.SHDSL ports are on the back of the SNE2040G, numbered from
left to right, 1–8. Switches 1–3 on the SNE2040G-P together provide eight bandwidth options for
the four G.SHDSL ports as a group. Bandwidth cannot be configured individually for the
G.SHDSL ports.
NOTE: Configuration switches 1–3 are used for G.SHDSL bandwidth configuration on the
SNE2040G-P ONLY. The SNE2040G-S determines bandwidth via communication with its
partner G.SHDSL provider equipment. Switches 4–8 are not currently used on the SNE2040G
provider or subscriber models.
Position switches 1–3 on the SNE2040G-P according to the cable distance for your connection
and your desired G.SHDSL bandwidth. Distance capabilities listed in the following table assume
the use of 26 American Wire Gauge (AWG) cable. Connections made with cable of a heavier
gauge will link up at greater distances. Your SNE2040 may not link up if the cable is in poor
condition or if the cable distance is greater than a particular bandwidth will support. If a link is
achieved under such conditions, traffic quality may be affected.
Table 1:
Bandwidth Configuration
Switch Position
1
Bandwidth (kbps)
2
3
Single Line
Connection
Distance
Double Line
Bonded
Connection
Feet
Meters
down
down
down
2,320
4,640
11,300
3,444
down
down
up
2,064
4,128
12,200
3,719
down
up
down
1,552
3,104
12,800
3,901
down
up
up
1,040
2,080
16,000
4,877
up
down
down
784
1,568
16,800
5,121
up
down
up
528
1,056
18,400
5,608
up
up
down
400
800
19,400
5,913
up
up
up
Adaptive*
Adaptive*
Varies
Varies
* The SNE2040G-P will run in Adaptive mode when switches 1–3 are in the Up position: the
four ports will train up to the best possible speed supported by the SNE2040G-P, the remote
G.SHDSL equipment, and the copper cable pair connecting the two.
SNE2-A2-ZN12-30
5
Connecting the SHDSL Lines
The primary feature of the SNE2040 is loop bonding capability among all four ports. However,
both the provider and subscriber units can function with a single G.SHDSL connection.
Link up time between local and remote SHDSL network extenders can vary from one to five
minutes depending on the quality, gauge and distance of the copper cables. If cable distance is
greater than a particular bandwidth will support, the units may not link up or, if they do achieve
link, traffic quality may be affected.
Loop Bonded Connection
Using two, three or four G.SHDSL lines for one network connection (loop bonding) will net two,
three or four times the speed and data passing capability as a single G.SHDSL connection.
Multiple G.SHDSL lines used for one connection provide backup for each other should one or
more of the lines become disabled.
NOTE: An SNE2040G must be connected with equipment that is also loop bonding capable in
order to utilize the loop bonding feature; see the document Product to Product SDSL Loop
Bonding Capability.
Procedure
To establish a loop bonding connection:
1 Plug your G.SHDSL cables into the G.SHDSL RJ45 ports (any combination of G.SHDSL 1,
2, 3 and 4) on the rear of the SNE2040G. The order of connection is not important.
2 Verify all connections: the G.SHDSL Link (Lnk) LED for each connected port will pulse
green to indicate the connection is established and operational.
Single Line Connection
A single line connection can be established between an SNE2040G-S and any of Zhone’s
G.SHDSL provider network extenders. Likewise, a single line connection can also be established
between an SNE2040G-P and any of Zhone's G.SHDSL subscriber network extenders.
Procedure
To establish a single line connection:
1 Plug your G.SHDSL cable into one of the four G.SHDSL RJ45 ports on the back of the
SNE2040G. Any of the four ports may be used.
2 Verify your connection: the G.SHDSL LED corresponding to the connected port (G.SHDSL
1–4) will flash green to indicate the connection is established and operational.
6
SNE2-A2-ZN12-30
SHDSL RJ45 Connector Pinouts
RJ45 Port
Table 2:
Cable and RJ45 Connector
SHDSL RJ45 Port
Pin
Connection
1
not used
2
not used
3
not used
4
Ring
5
Tip
6
not used
7
not used
8
not used
SNE2-A2-ZN12-30
7
Connecting the Ethernet Line
If a G.SHDSL connection has not yet been made, the Ethernet link will remain disabled (as
indicated by no illumination of the Ethernet 100, Act and Lnk LEDs) until at least one of the four
G.SHDSL links has been established.
Duplex Mode
The 10/100 Ethernet port auto-negotiates speed and duplex mode in accordance with the remote
equipment to which it is connected; Ethernet speed and duplex mode configurations cannot be
hard set on the SNE2040G. For the best connection results, the remote device (PC, hub, or
switch) should be set to auto-negotiate speed and duplex mode as well. If the remote device
cannot be configured to auto-negotiate, speed may be hard set at either 10 Mbps or 100 Mbps but
duplex mode must be hard set to Half Duplex; a 10/100 Ethernet connection will not operate
properly if the remote device is hard set to Full Duplex.
z
Half Duplex – Receive and transmit functions are mutually exclusive; data transmission
occurs in only one direction at a time. Packet collisions are not unusual.
z
Full Duplex – Receive and transmit functions occur simultaneously, effectively doubling
aggregate bandwidth and preventing packet collisions.
10/100 Ethernet RJ45 Pinouts
Table 3:
Ethernet RJ45 Connection
Pin
Connection
1
Rx+
2
Rx–
3
Tx+
4
not used
5
not used
6
Tx–
7
not used
8
not used
8
SNE2-A2-ZN12-30
LED Indicators
This document describes units manufactured after July 2004. See the prior version of this
document for information about units manufactured earlier.
Upon start up, the Ethernet link is disabled (as indicated by no illumination of the Ethernet 100,
Act, and Lnk LEDs) until at least one of the four G.SHDSL connections has been established.
Likewise, if established G.SHDSL connections are lost, the Ethernet link is automatically
disabled (as indicated by no illumination of the Ethernet 100, Act and Lnk LEDs) until at least
one of the connections has been reestablished.
Table 4:
SNE2040G LEDs (Sheet 1 of 2)
LED
STATE
INDICATION
ADDITIONAL INFORMATION
Power
Solid Green
Unit is
operational
If the Power LED is not
illuminated, it is unlikely that the
SNE2040 is receiving power and
therefore none of the LEDs will be
illuminated.
SDSL Link
(Lnk) Ports 1–4
Pulsing Green*
G.SHDSL
connection is
established and
active
Traffic is flowing.
Solid Green
problematic
G.SHDSL
connection
A connection exists but there is
indication of a problem with the
G.SHDSL line.
No Illumination
no G.SHDSL
connection
See note below.
Flashing Amber*
G.SHDSL
activity
The SNE2040G is receiving data.
Solid Amber
heavy Rx traffic
The SNE2040G is receiving large
amounts of data.
No Illumination
no activity
A G.SHDSL link may exist but the
SNE2040 is not receiving any data.
Flashing Amber*
G.SHDSL
activity
The SNE2040G is transmitting
data.
Solid Amber
heavy Tx traffic
The SNE2040G is transmitting
large amounts of data.
No Illumination
no activity
A G.SHDSL link may exist but the
SNE2040 is not transmitting any
data.
SDSL Data
Reception (Rx)
Ports 1–4
SDSL Data
Transmission
(Tx) Ports 1–4
SNE2-A2-ZN12-30
9
Table 4:
SNE2040G LEDs (Sheet 2 of 2)
LED
STATE
INDICATION
ADDITIONAL INFORMATION
100 Mbps
Ethernet Link
(100)
Solid Green
100 Mbps
Ethernet
connection is
established
If the Ethernet 100 LED is
illuminated, the Ethernet Lnk LED
will also be illuminated.
No Illumination
No 100 Mbps
Ethernet
connection
If the Ethernet 100 LED remains
unlit but the Ethernet Lnk LED is
illuminated then a connection has
been established at 10 Mbps rather
than 100 Mbps.
Pulsing Amber*
Standard
operation
Traffic is flowing without any
problems
Solid Amber
Heavy traffic
No Illumination
No activity
Either there is no Ethernet link or a
link exists but there is no activity.
Solid Green
Ethernet
connection is
established
If the Ethernet Lnk LED is
illuminated but not the Ethernet
100 LED then a 10 Mbps
connection has been established. If
the Ethernet 100 and Lnk LEDs are
BOTH illuminated then a 100
Mbps connection has been
established.
No Illumination
No Ethernet
connection
The Ethernet 100 and Act LEDs
will remain unlit by default.
10/100 Ethernet
Activity (Act)
10/100 Ethernet
Link (Lnk)
* A pulsing LED blinks steadily at a rate of once per second. A flashing LED blinks at a
more rapid, less constant rate.
10
SNE2-A2-ZN12-30
EMI Notices
United States – EMI Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
The authority to operate this equipment is conditioned by the requirements that no modifications
will be made to the equipment unless the changes or modifications are expressly approved by
Zhone Technologies, Inc.
If the equipment includes a ferrite choke or chokes, they must be installed as described in the
installation instructions.
Canada – EMI Notice
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
ACTA Customer Information
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the
ACTA. On the bottom of the network extender is a label that contains, among other information,
a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be
provided to the telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone network
must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. See
installation instructions for details.
If the network extender causes harm to the telephone network, the telephone company will notify
you in advance that temporary discontinuance of service may be required. But if advance notice
isn't practical, the telephone company will notify the customer as soon as possible. Also, you will
be advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures
that could affect the operation of the equipment. If this happens the telephone company will
provide advance notice in order for you to make necessary modifications to maintain
uninterrupted service.
SNE2-A2-ZN12-30
11
If trouble is experienced with this equipment, please contact your local sales representative,
service representative, or distributor directly for any help needed. For additional information
concerning warranty, sales, service, repair, installation, documentation, training, distributor
locations, or Zhone Technologies worldwide office locations, contact Global Service and
Support. See Technical Support on page 15.
If the equipment is causing harm to the telephone network, the telephone company may request
that you disconnect the equipment until the problem is resolved.
The customer may make no repairs to the equipment.
Connection to party line service is subject to state tariffs. Contact the state public utility
commission, public service commission or corporation commission for information.
Supplier's Declaration of Conformity
Place of Issue: Paradyne Corporation (now Zhone Technologies, Inc.)
8545 126th Avenue North
Largo, FL 33773-1502
USA
Date of Issue: 4/18/2005
Paradyne Corporation, located at the above address, hereby certifies that the Model
SNE2040G-P and Model SNE2040G-S bearing labeling identification number
US:AW2DLNANSNE2040 complies with: the Federal Communications Commission's ("FCC")
Rules and Regulations 47 CFR Part 68, and the Administrative Council on Terminal Attachments
("ACTA")-adopted technical criteria TIA-968-A, "Telecommunications - Telephone Terminal
Equipment -Technical Requirements for Connection of Terminal Equipment To the Telephone
Network, October 2002," as amended by ANSI/TIA-968-A-3 2004, "Telecommunications Telephone Terminal Equipment -Technical Requirements for Connection of Terminal Equipment
to the Telephone Network - Addendum 3."
Patrick Murphy
Senior Vice President, Chief Financial Officer, Paradyne Corporation
Notice to Users of the Canadian
Telephone Network
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical
Specifications. This is confirmed by the registration number. The abbreviation IC before the
registration number signifies that registration was performed based on a Declaration of
Conformity indicating that Industry Canada technical specifications were met. It does not imply
that Industry Canada approved the equipment.
12
SNE2-A2-ZN12-30
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is labeled on the
equipment. The REN assigned to each terminal equipment provides an indication of the
maximum number of terminals allowed to be connected to a telephone interface. The termination
on an interface may consist of any combination of devices subject only to the requirement that
the sum of the Ringer Equivalence Numbers of all the devices does not exceed five.
If your equipment is in need of repair, contact your local sales representative, service
representative, or distributor directly.
CE Marking
When the product is marked with the CE mark on the equipment label, a supporting Declaration
of Conformity may be downloaded from the Zhone World Wide Web site at www.zhone.com.
Japan Notice
Class A ITE
This is a Class A product based on the standard of the Voluntary Control Council for interference
by Information Technology Equipment (VCCI). If this equipment is used in a domestic
environment, radio disturbance may arise. When such trouble occurs, the user may be required to
take corrective actions.
SNE2-A2-ZN12-30
13
!
Important Safety Instructions
1 Read and follow all warning notices and instructions marked on the product or included in
the manual.
2 Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation
of the product and to protect it from overheating, these slots and openings must not be
blocked or covered.
3 Do not allow anything to rest on the power cord and do not locate the product where persons
will walk on the power cord.
4 Do not attempt to service this product yourself, as opening or removing covers may expose
you to hazardous voltage or to other risks. Refer all servicing to qualified service personnel.
5 General purpose cables are used with this product for connection to the network. Special
cables, which may be required by the regulatory inspection authority for the installation site,
are the responsibility of the customer. Use a UL Listed, CSA certified, minimum No. 26
AWG line cord for connection to the Digital Subscriber Line (DSL) network.
6 When installed, the product must comply with the applicable Safety Standards and
regulatory requirements of the country in which it is installed. If necessary, consult with the
appropriate regulatory agencies and inspection authorities to ensure compliance.
7 A rare phenomenon can create a voltage potential between the earth grounds of two or more
buildings. If products installed in separate buildings are interconnected, the voltage
potential may cause a hazardous condition. Consult a qualified electrical consultant to
determine whether or not this phenomenon exists and, if necessary, implement corrective
action prior to interconnecting the products.
8 Input power to this product must be provided by one of the following: (1) a UL Listed/CSA
certified power source with a Class 2 or Limited Power Source (LPS) output for use in
North America, or (2) a certified power source, with a Safety Extra Low Voltage (SELV)
output having a maximum of 240 VA available, for use in the country of installation.
9 In addition, since the equipment is to be used with telecommunications circuits, take the
following precautions:
— Never install telephone wiring during a lightning storm.
— Never install telephone jacks in wet locations unless the jack is specifically designed
for wet locations.
— Never touch uninsulated telephone wires or terminals unless the telephone line has
been disconnected at the network interface.
— Use caution when installing or modifying telephone lines.
— Avoid using a telephone (other than a cordless type) during an electrical storm. There
may be a remote risk of electric shock from lightning.
— Do not use the telephone to report a gas leak in the vicinity of the leak.
14
SNE2-A2-ZN12-30
Contacting Global Service and Support
Contact Global Service and Support (GSS) if you have any questions about this or other Zhone
products. Before contacting GSS, make sure you have the following information:
z
Zhone product you are using
z
System configuration
z
Software version running on the system
z
Description of the issue
Technical Support
If you require assistance with the installation or operation of your product, or if you want to
return a product for repair under warranty, contact GSS. The contact information is as follows:
E-mail
support@zhone.com
Telephone (North America)
877-ZHONE20
Telephone (International)
510-777-7133
Internet
www.zhone.com/support
If you purchased the product from an authorized dealer, distributor, Value Added Reseller (VAR),
or third party, contact that supplier for technical assistance and warranty support.
Service Requirements
If the product malfunctions, all repairs must be performed by the manufacturer or a
Zhone-authorized agent. It is the responsibility of users requiring service to report the need for
service to GSS.
Copyright ©2000–2005 Zhone Technologies and its licensors. All rights reserved.
SNE2-A2-ZN12-30
15
*SNE2-A2-ZN12-30*
*SNE2-A2-ZN12-30*
16
SNE2-A2-ZN12-30