E3949 V1
August 2008
VK266/VW266 Series
LCD Monitor
User Guide
VK266
VW266
Downloaded from ManualMonitor.com Manuals
Table of contents
Notices.......................................................................................................... iii
Safety information....................................................................................... iv
Care & Cleaning ........................................................................................... v
Chapter 1:
Product introduction
1.1
Welcome! ..................................................................................... 1-1
1.3
Assembling the monitor base...................................................... 1-2
1.2
1.5.
Package contents.......................................................................... 1-1
Monitor
1.5.1
1.5.2
Chapter 2:
2.1
2.2
3.2
3.3
3.4
3.5
Rear of the LCD monitor ................................................. 1-4
Setup
Detaching the arm/stand (for VESA wall mount)....................... 2-1
Adjusting the monitor................................................................... 2-2
Chapter 3:
3.1
..................................................................... 1-3
Front of the LCD monitor................................................. 1-3
General Instruction OSD (On-Screen Display) menu ................................................. 3-1
3.1.1
3.1.2
How to reconfigure........................................................... 3-1
OSD Function Introduction............................................... 3-1
Specifications summary............................................................... 3-4
Troubleshooting (FAQ)................................................................. 3-5
Supported operating modes........................................................ 3-6
HDMI Supported Primary Timings........................................... 3-7
Copyright © 2008 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated into any language in any form or by any means,
except documentation kept by the purchaser for backup purposes, without the express written permission
of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless
such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND
SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY
OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identification or explanation and to the
owners’ benefit, without intent to infringe.
iiDownloaded
from ManualMonitor.com Manuals
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with manufacturer’
s instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
•
•
Increase the separation between the equipment and receiver.
Consult the dealer or an experienced radio/TV technician for help.
As an Energy Star® Partner, our company has determined that this product meets
the Energy Star® guidelines for energy efficiency.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
Downloaded from ManualMonitor.com Manuals
iii
Safety information
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Before setting up the monitor, carefully read all the documentation that came
with the package.
To prevent fire or shock hazard, never expose the monitor to rain or moisture.
Never try to open the monitor cabinet. The dangerous high voltages inside the
monitor may result in serious physical injury.
If the power supply is broken, do not try to fix it by yourself. Contact a qualified
service technician or your retailer.
Before using the product, make sure all cables are correctly connected and the
power cables are not damaged. If you detect any damage, contact your dealer
immediately.
Slots and openings on the back or top of the cabinet are provided for
ventilation. Do not block these slots. Never place this product near or over a
radiator or heat source unless proper ventilation is provided.
The monitor should be operated only from the type of power source indicated
on the label. If you are not sure of the type of power supply to your home,
consult your dealer or local power company.
Use the appropriate power plug which complies with your local power standard.
Do not overload power strips and extention cords. Overloading can result in fire
or electric shock.
Avoid dust, humidity, and temperature extremes. Do not place the monitor in
any area where it may become wet. Place the monitor on a stable surface.
Unplug the unit during a lightning storm or if it will not be used for a long period
of time. This will protect the monitor from damage due to power surges.
Never push objects or spill liquid of any kind into the slots on the monitor
cabinet.
To ensure satisfactory operation, use the monitor only with UL listed computers
which have appropriate configured receptacles marked between 100-240V AC.
If you encounter technical problems with the monitor, contact a qualified service
technician or your retailer.
ivDownloaded
from ManualMonitor.com Manuals
Care & Cleaning
•
•
•
Before you lift or reposition your monitor, it is better to disconnect the cables
and power cord. Follow the correct lifting techniques when positioning the
monitor. When lifting or carrying the monitor, grasp the edges of the monitor.
Do not lift the display by the stand or the cord.
Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor
surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed
with a cloth dampened with mild cleaner.
Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended
for use with the LCD. Never spray cleaner directly on the screen, as it may drip
inside the monitor and cause an electric shock.
The following symptoms are normal with the monitor:
•
•
•
•
The screen may flicker during the initial use due to the nature of the fluorescent
light. Turn off the Power Switch and turn it on again to make sure that the
flicker disappears.
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
When the same image is displayed for hours, an afterimage of the previous
screen may remain after switching the image. The screen will recover slowly or
you can turn off the Power Switch for hours.
When the screen becomes black or flashes, or cannot work anymore, contact
your dealer or service center to fix it. Do not repair the screen by yourself!
Conventions used in this guide
WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying
to complete a task.
IMPORTANT: Information that you MUST follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.
Downloaded from ManualMonitor.com Manuals
Where to find more information
Refer to the following sources for additional information and for product and
software updates.
1.
2.
ASUS websites
The ASUS websites worldwide provide updated information on ASUS
hardware and software products. Refer to http://www.asus.com
Optional documentation
Your product package may include optional documentation, such as warranty
card, that may have been added by your dealer. These documents are not
part of the standard package.
viDownloaded
from ManualMonitor.com Manuals
1.1
Welcome! Thank you for purchasing the ASUS® VK266/VW266 Series LCD monitor!
The latest widescreen LCD monitor from ASUS provides a crisper, broader, and
brighter display, plus a host of features that enhance your viewing experience.
With these features, you can enjoy the convenience and delightful visual
experience that the VK266/VW266 Series brings you!
1.2
Package contents
Check your VK266/VW266 Series LCD package for the following items:
LCD monitor
Monitor base
1 x CD
Quick Start Guide
1 x Power cord
1 x VGA cable
1 x WebCam USB cable (Only for some models)
1 x DVI cable (Only for some models)
1 x Audio cable
If any of the above items is damaged or missing, contact your retailer
immediately.
ASUS LCDfrom
Monitor
VK266/VW266 Series Manuals
Downloaded
ManualMonitor.com
1-
1.3
Assembling the monitor base
To assemble the monitor base:
1.
2.
Connect the base with the monitor. A click indicates that the base has been
connected successfully.
Adjust the monitor to the angle that is most comfortable for you. We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
1
1.4
2
Connect cables
To connect cables:
1.
Remove back cover by hand carefully.
2.
Connect cables which you need base on chapter 1.5.2, Page1-4.
1-
Downloaded
from ManualMonitor.com Manuals
Chapter 1: Product introduction
1.5
Monitorintroduction
1.5.1
FrontoftheLCDmonitor
1
1.
2.
3.
4.
A
•
•
•
•
3
4
5
6
7
button:
Automatically adjust the image to its optimized position, clock, and phase
by long pressing this button for 2-4 seconds (for VGA mode only).
Use this hotkey to switch from five video preset modes (Game Mode, Night View Mode, Scenery Mode, Standard Mode, Theater Mode) with SPLENDID™ Video Enhancement Technology.
Exit the OSD menu or go back to the previous menu as the OSD
menu is active.
Button:
Press this button to decrease the value of the function selected
or move to the next fuction.
• This is also a hotkey for Volume adjustment. MENU Button:
• Press this button to enter/select the icon (function) highlighted while the OSD menu is activated.
•
•
5.
2
Button:
Press this button to increase the value of the function selected
or move to the previous fuction.
This is also a hotkey for Brightness adjustment.
Input Select Button
Use this hotkey to switch from VGA,DVI,HDMI, Component input signal.
(for some models)
Press
(Input Select Button) to display HDMI and component
signals after you connect cable with monitor.
Downloaded from ManualMonitor.com Manuals
ASUS LCD Monitor VK266/VW266 Series
1-3
Power button
• Press this button to turn the monitor on/off.
Power indicator
• Thecolordefinitionofthepowerindicatorisasthebelowtable.
6.
7.
Status
Blue
Amber
OFF
Description
ON
Standby mode
OFF
1.5.2 RearoftheLCDmonitor
Screwholesfor
VESAWallMount
6
8
Rearconnectors
1
1
2
3
4
7
9
AC-INport
2
HDMI-INport
3
DVIport
4
VGAport
5
SPDIF Out Port Of HDMI
6
YPbPr Ports + L/R Audio Ports
7
Line - in Port
8
Earphone - out Port
USB-IN port (Only for some models)
9
5
Downloaded
from ManualMonitor.com Manuals
1-4
Chapter 1: Product introduction
2.1
Detaching thearm/stand (for VESA wall mount)
The detachable stand of the VK266/VW266 Series LCD monitor is specially designed for
VESA wall mount.
To detach the arm/stand:
.
2.
3.
4.
Remove the back cover by hand carefully .
Remove the arm cover by hand carefully .
Have the front of the monitor face down on a table carefully . Use a screwdriver to
remove the three screws on the stand of the monitor as the below drawing shows.
Detach the arm from the monitor.
•
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
•
Hold the stand of the monitor when you remove the screws.
3 screws
The VESA wall mount kit (00 mm x 00 mm) is purchased separately.
For use only with UL Listed Wall Mount Bracket with minimum weight/load 7.9 Kg
(Screw size: 4mm x 12 mm)
ASUS LCD Monitor
VK266/VW266
Series
Downloaded
from
ManualMonitor.com
Manuals
2-
2.2
•
•
•
Adjusting themonitor
For optimal viewing, we recommend that you look at the full face of the monitor,
then adjust the monitor to the angle that is most comfortable for you.
Hold the stand to prevent the monitor from falling when you change its angle.
You can adjust the monitor’s angle from -5º to 20º.
-5º~20º
2.3
Install Life-Frame 2 software
ASUS VK266 series provides the easy-to-use LifeFrame 2 software that can
work with the webcam,allowing users to create their own photos or video clips.
®
•
LifeFrame 2 only supports Microsoft® Windows Vista/XP Service Pack 2
operating systems.
•
The LifeFrame 2 software is bundled in the support CD.
Installation instructions
1. Close all other applications.
2. Insert the support CD into the optical drive and run the LifeFrame 2 program.
3. Follow the on-screen instructions to complete the installation.
Downloaded
from ManualMonitor.com Manuals
2-2
Chapter 2: Setup
3.1
OSD (On-Screen Display) menu
3.1.1
How to reconfigure
1.
Press the MENU button to activate
the OSD menu.
2.
Press
and
to navigate through the functions. Highlight and activate
the desired function by pressing the MENU button. If the function selected
has a sub-menu, press
and
again to navigate through the sub-menu
functions. Highlight and activate the desired sub-menu function by pressing
the MENU button.
3.
Press
4.
and
to change the settings of the selected function.
To exit the OSD menu, press the
adjust any other function.
3.1.2
button. Repeat step 2 and step 3 to
OSD Function Introduction
1.
Spendid
This function contains five
sub-functions you can select
for your preference. Each mode has the
Reset selection, allowing you to maintain
your setting or return to the preset mode.
•
Scenery Mode: best choice for scenery photo display with SPLENDID™ Video Enhancement.
• Theater Mode: best choice for movie with SPLENDID™ Video Enhancement.
• • • Standard Mode: best choice for document editing with SPLENDID™ Video Enhancement.
Game Mode: best choice for game playing with SPLENDID™ Video
Enhancement.
Night View Mode: best choice for dark-scene game or movie with
SPLENDID™ Video Enhancement.
•
In the Standard Mode, the Satuation and ASCR functions are not
user-configurable.
•
In the other modes, the sRGB function is not user-configurable.
ASUS LCDfrom
Monitor
VK266/VW266 Series Manuals
Downloaded
ManualMonitor.com
3-
2.
Image
You can adjust brightness, contrast, sharpness, saturation,position (VGA
only), and focus (VGA only) from this main function.
P1
P2
•
Brightness: the adjusting range is from 0 to 100.
activate this function.
•
Sharpness: the adjusting range is from 0 to 100.
•
•
•
•
•
•
3.
3-
Downloaded
is a hotkey to Contrast: the adjusting range is from 0 to 00.
Saturation: the adjusting range is from 0 to 100.
ASCR:Select YES or NO to enable or disable dynamic contrast
ratio function. (for some models)
Over Drive:To speed up the respense time by Over drive technology.
the adjusting range is from 0 to 00(for some models)
Position: adjusts the horizontal postition (H-Position) and the vertical position (V-Position) of the image. The adjusting range is from 0 to 100.
Focus: reduces Horizonal-line noise and Vertical-line noise of the image by adjusting
(Phase) and (Clock) separately. The adjusting range is from 0 to 100.
•
Phase adjusts the phase of the pixel clock signal. With a wrong phase
adjustment, the screen shows horizontal disturbances.
•
Clock (pixel frequency) controls the number of pixels scanned by one
horizontal sweep. If the frequency is not correct, the screen shows vertical
stripes and the image is not proportional.
Color
Select the image color you like
from this function.
from ManualMonitor.com Manuals
Chapter 3: General Instruction
•
•
Color Temp.: contains five color modes including Cool, Normal,
Warm, sRGB, and User mode.
Skin Tone: contains three color modes including Reddish, Natural,
and Yellowish.
In the User mode, colors of R (Red), G (Green), and B (Bluee) are userconfigurable; the adjusting range is from 0-00.
4.
Input Select
In this function, you can select VGA,DVI,HDMI, YPbPr input source.
(Only for some models)
A
5.
System Setup
Allow you to adjust the system.
•
Volume: the adjusting range is from 0 to 100.
this function.
•
•
Language: there are ten languages for your selection, including English, German, Italian, French, Dutch, Spanish, Russian, Traditional Chinese, Simplified Chinese, Japanese, and Korean.
Aspect Controls: adjusts the aspect ratio to “Full” or “4:3”. (for some models)
•
Reset: “Yes” allows you to revert to the preset mode.
•
•
is a hotkey to activate OSD Setup: adjusts the horizontal postition (H-Position) and the vertical position (V-Position) of the OSD. The adjusting range is from 0 to 100. In the OSD Timeout selection, you can adjust the OSD timeout from 10 to 120.
Information: shows the monitor information.
ASUS LCDfrom
Monitor
VK266/VW266 Series Manuals
Downloaded
ManualMonitor.com
3-
3.2
Specifications summary
For VK266/VW266 series models
VK266H
Model
Panel Size
Max. Resolution
Brightness (Max.)
Intrisinc Contrast Ratio (Max.)
25.5"W
1920x1200
≧300cd/ ㎡
VW266H
25.5"W
1920x1200
≧300cd/㎡
≧1000:1
≧1000:1
≧160°(V) ; ≧170°(H)
≧160°(V) ; ≧170°(H)
Display Colors
16.7 M(6bit Hi FRC)
16.7 M(6bit Hi FRC)
Response Time
2ms (Gray to Gray)
2ms (Gray to Gray)
Webcam (built-in)
2.0M
-
Satellite Speaker
3W x 2 stereo
3W x 2 stereo
Earphone Output
Yes
Yes
Sound from HDMI
Yes
Yes
HDMI input
Yes
Yes
DVI with HDCP
DVI with HDCP
D-Sub input
Yes
Yes
Audio Line-in
Yes
Yes
RCA 3x2(YPbPr, R/L, SPIDIF)
Yes
Yes
Viewing Angle (CR=10)
DVI input
Power ON Consumption
Tilt
VESA Wall Mounting
85W
85W
+25° ~ -5°
+25° ~ -5°
Yes (100mm x 100mm) Yes (100mm x 100mm)
Phys. Dimension (WxHxD)
596x461x240
596x449x240
Box Dimension (WxHxD)
693x528x206
693x528x206
Net Weight (Esti.)
7.9
Gross Weight (Esti.)
11.1
11.1
AC:100~240V(Built-in)
AC:100~240V(Built-in)
Voltage Rating
7.9
*Specificationsaresubjecttochangewithoutnotice.
Downloaded
3-
from ManualMonitor.com Manuals
Chapter 3: General Instruction
3.3
Troubleshooting (FAQ)
Problem
Possible Solution
Power LED is not ON
• Press the button to check if the monitor
is in the ON mode.
• Check if the power cord is properly
connected to the monitor and the power
outlet.
The power LED lights amber and there is no • Check if the monitor and the computer are
screen image
in the ON mode.
• Make sure the signal cable is properly connected the monitor and the computer.
• Inspect the signal cable and make sure
none of the pins are bent.
• Connect the computer with another
available monitor to check if the computer
is properly working.
Screen image is too light or dark
• Adjust the Contrast and Brightness settings
via OSD.
Screen image is not centered or sized
• Press the A button for two seconds to
properly
automatically adjust the image.
• Adjust the H-Position or V-Position settings
via OSD.
Screen image bounces or a wave pattern is • Make sure the signal cable is properly
present in the image
connected to the monitor and the computer.
• Move electrical devices that may cause
electrical interference.
Screen image has color defects (white does • Inspect the signal cable and make sure that
not look white)
none of the pins are bent.
• Perform Reset via OSD.
• Adjust the R/G/B color settings or select the
Color Temperature via OSD.
Screen image is blurry or fuzzy
• Press the A button for two seconds to
automatically adjust the image (for VGA
mode only).
• Adjust the Phase and Clock settings via
OSD.
No sound or sound is low
• Ensure that the audio cable is properly
connected to the monitor and the computer
• Adjust the volume settings of both your
monitor and computer.
• Ensure that the computer sound card driver
is properly installed and activated.
Webcam is not working
• Make sure that you have connected the
USB 2.0 cable securely to both the LCD
monitor and your computer.
• Make sure that you use the Microsoft ®
Windows ® Vista/XP Service Pack 2
operation systems.
ASUS LCDfrom
Monitor
VK266/VW266 Series Manuals
Downloaded
ManualMonitor.com
3-
3.4 VK266/VW266 PC Supported Timing List
VESA Modes, Factory Preset Timings
Mode
VGA
Input Resolution
Aspect
Ratio
4:3
640x480,60Hz
640x480,72Hz
SVGA
4:3
XGA
4:3
SXGA
4:3
5:4
WXGA+
16:10
WSXGA
1080P
WUXGA
16:10
16:9
16:10
H(KHz)
V(Hz)
Pixel(MHz)
640x480,75Hz
31.469
37.861
37.5
59.94
72.809
75
25.175
31.5
31.5
640x480, 85Hz
800x600,56Hz
800x600,60Hz
800x600,72Hz
800x600,75Hz
800x600,85Hz
1024x768,60Hz
1024x768,70Hz
1024x768,75Hz
1024x768,85Hz
1152x864,75Hz
1280x960,60Hz
1280x1024,60Hz
1280x1024,75Hz
1440x900,60Hz
1440x900,75Hz
1680x1050,60Hz
1920x1080, 60Hz
1920x1200,60Hz
43.269
35.156
37.879
48.077
46.875
53.674
48.363
56.476
60.023
68.677
67.5
60
63.981
79.976
55.935
70.635
65.29
67.5
74.038
85.008
56.25
60.317
72.188
75
85.061
60.004
70.069
75.029
84.997
75
60
60.02
75.025
59.887
79.984
59.954
60
59.95
36
36
40
50
49.5
56.25
65
75
78.75
94.5
108
108
108
135
106.5
136.75
146.25
148.5
154
IBM Modes, Factory Preset Timings(D-SUB, DVI-D, HDMI inputs)
Mode
DOS
DOS
Input Resolution
Aspect
Ratio
640x350, 70Hz
640x350,85Hz
720x400, 70Hz
720x400,85Hz
H(KHz)
V(Hz)
Pixel(MHz)
31.469
37.861
31.469
37.927
70.087
85.08
70.087
85.039
25.175
31.5
28.322
35.5
MAC Modes, Factory Preset Timings(D-SUB, DVI-D, HDMI inputs)
Mode
VGA
SVGA
Input Resolution
Aspect
4:3
640x480, 67Hz
4:3
832x624, 75Hz
H(KHz)
V(Hz)
Pixel(MHz)
35
49.725
66.667
74.551
30.24
57.2832
H(KHz)
V(Hz)
Pixel(MHz)
44.772
56.456
47.776
60.289
49.702
62.795
66.587
59.855
74.777
59.87
74.893
59.81
74.934
59.934
74.5
95.75
79.5
102.25
83.5
106.5
138.5
VESA Modes, User Available Timings
Mode
720P
WXGA+
1080P
3-
Downloaded
Input Resolution
Aspect
16:9
1280x720, 60Hz
16:9
1280x720, 75Hz
1280x768, 60Hz
1280x768, 75Hz
16:10 1280x800, 60Hz
16:10 1280x800, 75Hz
16:9
1920x1080, 60Hz
from ManualMonitor.com Manuals
Chapter 3: General Instruction
VK266H / VW266H HDMI Supported Primary Timings
Mode
Input
Aspect
4:3
480i
16:9
4:3
480P
4:3
16:9
576i
576P
720P
4:3
16:9
4:3
16:9
16:9
16:9
16:9
1080i
16:9
Resolution
H(KHz)
V(Hz)
720(1440)x480i 15.734/
59.94 / 60
15.75
59.94/60 Hz
720(1440)x480i 15.734/
59.94 / 60
15.75
59.94/ 60 Hz
31.469/31.5
640x480P
59.94/60
59.94 / 60 Hz
720x480P
31.469 /
59.94 / 60
31.5
59.94 / 60 Hz
720x480P
59.94 / 60 Hz
1440x576i, 50
1440x576i, 50
720x576P, 50Hz
720x576P, 50Hz
1280x720P,
1280x720P
59.94 / 60 Hz
1920x1080i,
1920x1080i
59.94/ 60 Hz
31.469 /
31.5
15.625
15.625
31.25
31.25
37.5
Pixel(MHz)
27 /27.027
27 /27.027
25.175/25.2
27 /27.027
59.94 / 60
27 /27.027
50
50
50
50
50
27
27
27
27
74.25
44.955/45 59.94/60
74.176/74.25
28.125
33.716/
33.75
50
74.25
59.94/60
74.176/74.25
VK266H/VW266H HDMI Supported Optional Timings
Mode
Input
Aspect
4:3
480P
16:9
576P
4:3
16:9
16:9
1080P
16:9
Resolution
H(KHz)
31.469/
1440x480P
31.5
59.94/ 60 Hz
31.469/
1440x480P
31.5
59.94 / 60 Hz
31.25
1440x576P, 50Hz
1440x576P, 50Hz
31.25
1920x1080P,
56.25
50Hz
1920x1080P,
67.433/67.5
59.94 /60 Hz
V(Hz)
Pixel(MHz)
59.94/60
54/54.054
59.94/60
54/54.054
50
50
54
54
50
148.5
59.94/60
148.352/
148.5
VK266H/VW266H YPbPr Input List
Mode
Input
Aspect
480i
4:3
480P
4:3
576i
4:3
576P
4:3
16:9
720P
16:9
16:9
1080i
16:9
16:9
1080P
16:9
Resolution
720x480i
59.94 Hz
720x480P
60 Hz
720x576i
50 Hz
720x576P
50Hz
1280x720P
50Hz
1280x720P
59.94/60 Hz
1920x1080i
50Hz
1920x1080i
59.94 Hz
1920x1080P
50 Hz
1920x1080P
59.94/60 Hz
H(KHz)
V(Hz)
Pixel(MHz)
15.734
59.94
13.5
31.5
60
27
15.625
50
13.5
31.25
50
27
37.5
50
74.25
44.955/45
28.125
33.716/
33.75
59.94/60 74.176/74.25
50
74.25
59.94/60 74.176/74.25
56.25
50
74.25
67.432/
67.5
59.94/60
148.5
*Modesnotlistedintheabovetablesmaynotbesupported.Foroptimalresolution,werecommend
thatyouchooseamodelistedintheabovetables
3-7
Downloaded
from ManualMonitor.com Manuals
Chapter 3: General Instruction