User manual | Mitox LS700BS Operator`s manual

www.mitoxgm.co.uk

Operator’s Manual

user manual, maintenance instructions and spare parts

LS700BS 7 Ton Petrol Logsplitter

Read this manual carefully before operating the machine

Original Instructions Version April 13


SAFETY WARNINGS & EXPLANATION OF SYMBOLS ON THE MACHINE

UNDERSTAND YOUR LOG SPLITTER

Read and understand the owner’s manual and labels affixed to the log splitter. Learn its application and limitations as well as the specific potential hazards peculiar to it.

DRUGS, ALCOHOL AND MEDICATION

Do not operate the log splitter while under the influence of drugs, alcohol, or any medication that could affect your ability to use it properly.

AVOID DANGEROUS CONDITIONS

Always operate your log splitter on dry, solid, level ground. Never operate your log splitter on slippery, wet, muddy, or icy surfaces. Keep your work area clean and well lit. Cluttered areas invite injuries. Do not use the log splitter in wet or damp areas or expose it to rain. Do not use it in areas where fumes from paint, solvents or flammable liquids pose a potential hazard.

INSPECT YOUR LOG SPLITTER

Check your log splitter before turning it on. Keep guards in place and in working order.

Replace damaged, missing or failed parts before using it. Make sure all nuts, bolts, screws, hydraulic fittings, hose clamps, etc. are securely tightened. Always check the oil level in the hydraulic oil tank. Never operate your log splitter when it is in need of repair or is in poor mechanical condition.

WORK WEAR

Do not wear loose clothing, neckties or jewellery (rings, wrist watches). They can be caught in moving parts. Protective gloves and safety footwear are recommended when working. Wear protective hair covering to contain long hair, preventing it from getting caught in machinery.

PROTECT YOUR EYES AND FACE

Any log splitter may throw foreign objects into the eyes. This can cause permanent eye damage. Always wear safety goggles. Everyday eyeglasses have only impact resistant lenses.

They are not safety glasses.

PREVENT FIRES

Do not smoke or have open flames when operating or refuelling the log splitter. Never operate the log splitter near a flame or spark. Oil is flammable and can be ignited.

KEEP BYSTANDERS AWAY

Allow only one person to load and operate the log splitter. Always keep bystanders, including visitors, children and pets away from the work area, especially when the log splitter is under operation. Only the operator should stand near the machine and only within the safe operating area of 5 metres. Never use another person to help you with freeing a jammed log. No one under the age of 16 should be allowed to operate the log splitter. Any individual under the age of 18 should always be under the supervision of an an adult.

INSPECT YOUR LOG

Never attempt to split logs containing nails, wire or debris. Always make sure that both ends of the log you are splitting are cut as square as possible. This will prevent the log from sliding out of position while under pressure. Branches must be cut off flush with the trunk.

2



DON’T OVERREACH

Keep a proper footing and balance at all times. Never stand on the log splitter. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted. Do not store anything above or near the log splitter where anyone might stand on the tool to reach it.

AVOID INJURY FROM UNEXPECTED ACCIDENT

Do not straddle or reach across the splitting area when operating the log splitter. Never pile logs to be split in a manner that will cause you to reach across the log splitter. Only use your hands to operate the control levers. Never use your foot, knee, a rope, or any other extension device. Always pay full attention to the movement of the wedge ram. Never attempt to load your log splitter while the ram is in motion. Keep hands out of the way of all moving parts.

Never try to split two logs. One of them may fly up and hit you.

PROTECT YOUR HANDS

When the ram of the log splitter is in the return mode, keep your hands off the machine – the log splitter is designed to automatically stop when the cylinder is fully retracted. Keep your hands away from splits and cracks which open in the log. They may close suddenly and crush or injure your hands. Do not remove jammed logs with your hands.

INCORRECT USE

The log splitter will do a better and safer job working at its designed rate. Don’t use the log splitter for a purpose for which it was not intended. Do not, under any circumstances, alter your log splitter. This equipment was designed and engineered to be used in accordance with the operating instructions. Altering the equipment, or using the equipment in such a way as to circumvent its design capabilities and capacities, could result in serious or fatal injury and will void the warranty. Never try to split logs larger than those indicated in the specifications table. This could be dangerous and may damage the machine.

NEVER LEAVE THE LOG SPLITTER RUNNING UNATTENDED

Don’t leave the tool until it has come to a complete stop.

FOR YOUR SAFETY

Do not remove or tamper with any of the machines protection or safety devices or modify the log splitter in any way.

PROTECT THE ENVIRONMENT

Take used oil to an authorized collection point or follow the stipulations in the country where the log splitter is used. Do not discharge into drains, soil or water.

MAINTAIN YOUR LOG SPLITTER WITH CARE

Always clean the unit after each use. Keep the log splitter clean for best and safest performance.

Follow the instructions for lubricating. Inspect all hydraulic seals, hoses and couplers for leaks prior to use. Control levers and power switch must be kept clean, dry and free from oil and grease at all times.

MAKE THE WORKSHOP CHILDPROOF

Lock the shop. Store the log splitter away from children and others not qualified to use it.


3


UNDERSTAND YOUR MACHINE

Read and understand the operator’s manual and labels affixed to the machine. Learn its application and limitations as well as the specific potential hazards peculiar to it.

Be thoroughly familiar with the controls and their proper operation. Know how to stop the machine and disengage the controls quickly.

Make sure to read and understand all of the instructions and safety precautions as outlined in the Engine Manual, packed separately with your unit. Do not attempt to operate the machine until you fully understand how to properly operate and maintain the Engine and how to avoid accidental injuries and/or property damage.

WORK AREA

Never start or run the engine inside a closed area. The exhaust fumes are dangerous, containing carbon monoxide, an odorless and deadly gas. Operate this unit only in a well ventilated outdoor area.

BURN RISK

Take care not to touch the hot muffler/exhaust, gear housing and cylinder.

TABLE OF CONTENTS

Safety Warnings & Cautions .….….….….….….….….….….….…………………………………………………………………..........2

Application Conditions ....….….….….…………….….….….….……………………………………………………………….…….....5

Specifications….….….……………………………….….….….….….………………………………………………..........5

Contents of Container …..….….….….….….….….….….….….….…………………………………………………………………. .....6

Set up and Preparation for Operation…….……….….….….….….….….….….…………………………………………………….......6

Delivering Log Splitter to Work Site ..….….….….….….….….….….….….….….….…………………………………......................................7

Log Splitter Operation ...........…….….….….….….….….….….….….….………………………………………………………. ...................8

Replacing Hydraulic Oil ……….….….….….….….….….….….………………......…………………………………………………....9

Sharpening Wedge ............…….….….….….….….….….….….….….………………….............……………………………………….....10

Trouble Shooting ………………….….….….….….….….….….….….……………………………………………….............………....10

Wiring Diagram ………………….….….….….….….….….….….………………………………….……………………………..........10

Hydraulic Plumbing Diagram ………………….….….….….….….….….….….……………………………………………......…….10

Parts Schematic .....…………….….….….….….….….….….….….….….….….……………………………...........................................................11

Declaration of Conformity….….….….….….….….….….….….….….….….……………………………...........................................................14

4



DESCRIPTION OF MACHINE

The log splitter is designed to be used in a domestic application.

The log splitter is designed exclusively for the following applications:

-Splitting freshly cut timber that does not exceed the dimensions specified in the technical data.

The 4-way splitting cross is only to be used on freshly cut wood and not seasoned wood as this type of wood can splinter and put undue strain on the log splitter.

ENGINE INFORMATION

The Engine Manufacturer is responsible for all engine-related issues with regards to performance, power rating, specifications, warranty and service. Please refer to the Engine Manual, packed separately with your unit, for more information.

APPLICATION CONDITIONS

This log splitter is designed for operating under ambient temperatures between +5ºC and 40ºC. It can be stored or transported under ambient temperatures between -25ºC and 55ºC.

SPECIFICATIONS

Model Number

Motor

Max rpm

Log Capacity

Maximum Force

Hydraulic Pressure

Hydraulic Oil Capacity

Ram Travel

Forward Speed

Retract Speed

Noise Level

Overall Sizes

Weight

Diameter

Length

Length

Width

Height

LS700

196cc, 6.5 HP

3600

12cm - 32cm

104cm / 78cm / 52cm

7 Ton

2581 PSI

6 L

475mm

4.9cm / sec.

22.3cm / sec

88.1dbA under no load ;

93.0dbA under full load

107cm

46 cm

103 cm

125kg

ENVIRONMENTAL INFORMATION

Recycle unwanted materials instead of disposing of them as waste. All tools, hoses and packaging should be sorted, taken to the local recycling center and disposed of in an environmentally safe way.


5


FUEL SAFETY

Fuel is highly flammable, and its vapours can explode if ignited. Take precautions when using the log splitter to reduce the chance of serious personal injury.

When refilling or draining the fuel tank, use an approved fuel storage container while in a clean, well-ventilated outdoor area. Do not smoke, or allow sparks, open flames or other sources of ignition near the area while adding fuel or operating the unit. Never fill the fuel tank indoors.

Keep grounded conductive objects, such as tools, away from exposed, live electrical parts and connections to avoid sparking or arcing. These events could ignite fumes or vapours.

Always stop the engine and allow it to cool before filling the fuel tank. Never remove the cap of the fuel tank or add fuel while the engine is running or when the engine is hot. Do not operate a machine with known leaks in the fuel system.

Loosen the fuel tank cap slowly to relieve any pressure in the tank.

Never overfill the fuel tank. Fill the tank to no more than 12.5mm (1/2”) below the bottom of the filler neck to provide space for expansion as the heat of the engine and/or sun causes fuel to expand.

Replace all fuel tank and container caps securely and wipe up spilled fuel. Never operate the unit without the fuel cap securely in place.

Avoid creating a source of ignition for spilled fuel. If fuel is spilled, do not attempt to start the engine but move the machine away from the area of spillage and avoid creating any source of ignition until fuel vapours have dissipated.

Store fuel in containers specifically designed and approved for this purpose.

Never store fuel or a machine with fuel in the tank inside a building where fumes may reach a spark, open flame, or any other sources of ignition. Allow the engine to cool before storing in any enclosure. Drain fuel before transport.

Machines stored and not used for over 30 days need the fuel to be stabilised, or drained of fuel to prevent gum forming in the fuel system, carburettor, petrol pump etc. We recommend the use of Briggs & Stratton fuel stabiliser (992381). Mix fuel stabiliser with fuel in the fuel tank, or storage containers, and run the engine for a short time to circulate the stabiliser through the carburettor. Engine and fuel can then be stored for up to 12 months.

SERVICE

Before cleaning, repair, inspecting, or adjusting, shut off the engine and make certain all moving parts have stopped. Always make sure the engine’s throttle control is in its “STOP” position.

Disconnect the spark plug wire, and keep the wire away from the plug to prevent accidental starting.

Have your machine serviced by qualified repair personnel using only genuine replacement parts. This will ensure the safety of the machine is maintained.

6



CONTENTS OF THE CONTAINER

A. Log Splitter Frame …………................................1 set

B. Control Lever and Guard Assy................................2sets

C. Removable Support Table....…...............................1 pc

D. Owner’s Manual ……….....…….….....................1 pc

E. Cross Splitter ……….....…….….............................1 pc

E

SET UP AND PREPARATION FOR OPERATION

A

1. Pull Spring Pin (A) to remove the Lock Pin (B). Apply a thin coat of grease to both surfaces of the Control Lever Guard as illustrated.

Insert the Control Lever and Guard Assy and make sure the Control Lever End goes into the slot of Connection Bracket (C). Lock the Control Lever and Guard Assy down with the Lock Pin (B) and Spring Pin (A). Follow the same steps to install the other Control

Lever and Guard Assy on the other side.

2. 3 installation positions are available for the Support Table for different splitting lengths. At every installation position, Lock Down

Hooks (D) are available. Insert the Support Table in the selected Brackets (E). Turn the Lock Down Hooks (D) on both sides by 90 degrees to lock the Support Table down.


7


3. Familiarize yourself with the controls and features of this log splitter as shown in the illustrations.

1. Transport Handle

2. Ram Travel Adjusting Rod

3. Split Wedge

4. Ram

5. Control Levers Connection Bracket

6. Top Motor Shield

7. Fuel Tank

8. Wheels

9. Base

10. Oil Tank Cover / Air Bleeder

11. Table Lock Down Hook

12. Support Table

13. Side Bracket for Support Table

14. Front Bracket for Support Table

15. Control Lever

16. Control Lever Guard

17. Adjustable Log Holder

18. Log Holder Adjusting Knob

Bleed the air out of the hydraulic system before starting the log splitter.

The bleed screw should be loosened by two rotations until air can go in and out of the oil tank smoothly. Air flow through the oil tank filler should be detectable during the operations. Before moving the log splitter, make sure the bleed screw is tightened to avoid oil leaking from this point.

THE FAILURE TO LOOSEN THE BLEED SCREW WILL

RESULT IN DAMAGE TO THE SEALS OF THE

HYDRAULIC SYSTEM AND CAUSE PERMANT

DAMAGE TO THE LOG SPLITTER.

DELIVERING THE LOG SPLITTER TO THE WORK SITE

The log splitter is equipped with 2 wheels for minor moving. To move the log splitter to the work site. Grip the handle (A) to tilt the log splitter slightly after making sure the bleed screw is tightened.

If using a crane, lay hoist sling around the housing. Never try to lift the log splitter at the Handle (A).

8



LOG SPLITTER OPERATION

1. Plan your work site. Work safely and save effort by planning your work before hand. Have your logs positioned where they can be easily reached. Have a site located to stack the split wood or load it onto a nearby truck or other carrier.

2. Prepare the logs for splitting. This splitter accommodates logs up to 104cm in length. When cutting up limbs and large sections, do not cut sections any longer than 100cm. The 3 support table positions are for splitting logs up to

52cm, 78cm 104cm in length. Insert the support table in the position nearest to the log length, and secure the support table with the locking hook.

Do not attempt to split seasoned logs. Green logs split much more easily, and will not put undue pressure on the splitter.

Seasoned logs can also split violently, which can be dangerous to the operator.

3. Applying a thin coat of grease to the surfaces of the ram before operation will lengthen the durability of the ram.

4. Start the engine, following the procedure listed in the Briggs & Stratton engine manual. The splitting wedge should rise to its highest position automatically.

5. Open the Air Bleed. Loosen the oil tank cover two turns whenever the splitter is being used. Retighten this cover when you finish.

6. While operating under extremely low temperature, keep the log splitter running under no load for 15 minutes to preheat the hydraulic oil.

7. Before initial operation, check to be sure the two-handed operation is properly functioning by following these steps:

(1)

(2)

Lower both control levers, splitting wedge lowers to approx 5cm above the highest table position.

Release either of the levers, splitting wedge should remain in the original position.

(3) Release both levers, the ram should rise to the highest position

automatically.

8. To set the wedge ram stroke, take the following steps:

(1)

(2)

(3)

Move the splitting wedge to desired position. The upper position of the ram wedge travel should be about 3~5cm over the logs to be split.

Release one control lever and switch off the engine

Release the Setscrew (A) and Raise Adjusting Rod (B) until

Adjusting Rod (B) begins to be stopped by the spring inside. Tighten the Setscrew (A).

(4) Release both control levers and start the engine

(5) Check upper position of splitting wedge.


9


9. Place log onto splitter. Place the log onto the support table vertically and sitting flat on the support table. Be sure the wedge and support table will contact the log squarely on the ends. Never attempt to split a log at an angle.

Split log in the direction of its growing grain. Do not place logs across the log splitter for splitting. It may be dangerous and may seriously damage the machine.

10. Adjust the Log Holders (A) according to the diameter of the log to obtain most comfortable Control Levers angle.

11. Hold the log with the clamping brackets. Lower levers to start the splitting. Releasing either lever stops the motion of the splitting wedge.

Releasing both handles returns the splitting wedge to the upper position.

12. Stack as you work. This will provide a safer work area, by keeping it uncluttered, and avoid the danger of tripping.

4 WAY SPLITTING CROSS

Mount the 4 way splitting cross over the splitting wedge and secure in place using the fixing screw, ensuring that it is firmly secured.

The 4-way splitting cross is only to be used on freshly cut wood and not seasoned wood as this type of wood can splinter and put undue strain on the log splitter.

Accumulated split wood and wood chips can create a hazardous work environment. Never continue to work in a cluttered work area which may cause you to slip, trip or fall.

REPLACING HYDRAULIC OIL

The hydraulic system is a closed system with oil tank, oil pump and control valve. Check oil level regularly with dipstick. Low oil level can damage the oil pump. Oil Level should measure approx. 1 ~ 2 cm lower than the upper surface of the oil tank. The oil should be completely changed once a year.

-Make sure moving parts stop and the log splitter is unplugged.

-Make sure that no dirt or debris finds its way into the oil tank

-Collect used oil and responsibly recycle.

-Following an oil change, activate the log splitter a few times without splitting

Hydraulic oil recommended for the log splitter’s hydraulic system:

HLP 22

Use a drain pan to aid in the removal of all used oil and particles.

Remove oil drain plug to drain oil from the hydraulic transmission system. Examine oil for metal chips as a precaution to future problems.

After oil has been completely drained from the Oil filler, reinstall drain plug.

Fill the hydraulic transmission system with recommended oil through the filler plug opening, to the correct level.

10



Read dipstick to determine the maximum and minimum oil level.

To check the hydraulic oil, unscrew the oil filler plug and wipe the dip stick rod with a clean cloth. Next insert the dip stick into oil tank without screwing it into the tank. The oil should be between the markings Min and Max. Top up the oil if necessary.

Low oil can damage the oil pump. Overfilling can result in excessive temperature in the hydraulic transmission system.

SHARPENING WEDGE

This log splitter is equipped with a reinforced splitting wedge with a specially treated blade. After long periods of operation, and when required; sharpen the wedge using a fine-toothed file removing any burrs or flat spots on the edge.

TROUBLESHOOTING

PROBLEM

Engine does not start

Log Splitter does not work while motor running

Log Splitter works with abnormal vibration and noise

PROBABLE CAUSE

Engine oil level is low

Ignition switch is OFF

Bleed valve is not opened

REMEDY SUGGESTED

Fill engine with oil to correct level

Set ignition to ON

Open bleed valve

Control Levers or Connection parts bent Replace the damaged parts

Low hydraulic oil level

Low hydraulic oil level

Check and refill hydraulic oil

Check and refill hydraulic oil

If the solutions above fail to resolve the problem or the machine is not safe to use then contact the suppying dealer.

HYDRAULIC

PLUMBING DIAGRAM


11


12



ID PART No

1 MICCQ01

2 MICCQ62

3 MIGG/T93-1987

4 MIGB/T822-2000

5 MIGB3452.1-92

6 MICCA.00.101

7 MIGB/T95-1985

8 MICCA.00.109

9 MIGB/T5781-2000

10 MICCA.00.107

11 MICCQ03.1.1

12 MICCA.00.125

13 MICBC.40.113

14 MICCA.00.105

15 MICCB.05.002

16 MICCA.00.122

17 MICCA.00.120

18 MICCA.00.119

19 MICCA.00.121

20 MICCA.00.106

21 MICCQ04.1.1

22 MIGB/T822-2000

23 MIGB/T95-1985

24 MIGB/T802

25 MICFA.00.018

26 MIGB/T894.1-1986

27 MIGB/T5786-2000

28 MIJB982-77

29 MICCA.00.123

30 MICCA.00.126

31 MICCA.00.129

32 MICCA.00.124

33 MICCA.00.118

34 MILS700BS-34

35 MICCQ59

36 MIGB/T93-1987

37 MILS700BS-37

38 MIGB/T5785-2000

39 MIGB/T894.1-1986

40 MICCA.00.102

41 MICCQ02

42 MIGB/T5781-2000

43 MICCA.02.104

44 MILS700BS-44

45 MICCD.00.103

46 MICCA.02.103

DESCRIPTION

UPRIGHT TUBE WELDMENT - B&S

PUMP GUARD

SPRING WASHER M6

SCREW M6X12

O-RING 23.6X3.55G

CAP

WASHER M10

LOCK-OUT LEVER

BOLT M10X35

R/H CLAMPING FORK

R/H GUARD ASSY

KNOB M8X20

FORK

CONTROL LEVER SHAFT

WORK TABLE 2

PLASTIC INSERT (4)

PLASTIC INSERT (2)

PLASTIC INSERT (1)

PLASTIC INSERT (3)

L/H CLAMPING FORK

L/H GUARD ASSY

SCREW M6X10

WASHER M6

LOCKNUT M10

WHEEL A

CIRCLIP 16

BOLT M16X15

WASHER GROUPWARE 16

SLIDING PLATE

KNOB

WEDGE BRACKET ROUND COVER

ROUND COVER

SQUARE COVER

NUT M20

HIGH PRESSURE OIL HOSE 24

SPRING WASHER M8

LOCKNUT M6

BOLT M8X25

CIRCLIP 22

LOCK SHAFT

CCQ CYLINDER

HEX BOLT

LEVER HANDLE

LOCKNUT M8

PIN D

OPERATE HANDLE


1

2

1

4

2

1

6

2

6

6

1

1

1

1

1

1

2

1

2

2

1

1

6

8

1

1

1

26

1

1

QTY

1

2

1

2

2

2

1

1

2

4

6

1

3

1

1

1

47 MIGB/T41-2000

48 MIGB/T95-1987

49 MICCA.09.001

50 MIGB/T802

51 MICCA.07.109(0)

52 MILS700BS-52

53 MICCA.00.108

54 MICCA.09.103(0)

55 MIGB/T6172.1

56 MICCA.08.001

57 MILS700BS-57

58 MIGB/T5780-2000

59 MICCA.16.001

60 MICCB.07.001

61 MICCQ43

62 MIJ982-1977

63 MICCQ57

64 MICCQ60

65 MICCQ34

66 MILS700BS-66

67 MICCQ61

68 MICCQ29

69 MICDB2-F203.4ALP

70 MICCQ46.4

71 MICCQ46.3

72 MII/C6.5HP

73 MIGB/T5785-2000

74 MICCQ68

75 MIGB/T5786-2000

76 MICL090 12.7-19

77 MILS700BS-77

78 MILS700BS-78

79 MICCQ51

80 MICCQ32

81 MI700-79

82 MI700-80

THIN NUT

WASHER M8

CONTROL LINK PLATE

NUT

DRAW ROD LOCK COVER

SUPPORTING RING

DRAW ROD

DRAW SLEEVE NUT

THIN NUT M16

DRAW SLEEVE

HOSE CLAMP 22-28

BOLT M6X30

CA VALVE

WEDGE BRACKET WELDMENT B

T-CONNECTOR - TAPE

WASHER GROUPWARE 20

VALVE TUBE NOZZLE

HIGH PRESSURE OIL HOSE 24

VALVE INJECTION NOZZLE

OIL RETURN PIPE

HIGH PRESSURE OIL HOSE

NOZZLE 9/16-18-UNF-2BXM20X1.5

GEAR PUMP

ORIENTATION RING

JOINING

ENGINE (B&S)

BOLT M8X35

RUBBER WASHER (UR)

BOLT M8X30

REV JOINT - CL090 12.7-20

GRUB SCREW

INTAKE HOSE

TIE-IN 20

NOZZLE 3/4-16-UNF-2BXM20X1.5

CROSSCUT WEDGE - VERTICAL

WEDGE RETAINING BOLT

2

1

4

1

4

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

12

4

1

1

1

1

1

1

1

1

1

6

14

13


EC Declaration of Conformity

We herewith declare

that the following machine complies with the appropriate basic safety and health requirements of the EC Directive based on its design and type, as brought into circulation by us.

In case of alteration of the machine, not agreed by us, this declaration will lose its validity.

Description : Log Splitter

Type: 65581 (MITOX LS700BS)

Test report No. 17702004

Applicable EC Directives : EC Directive of Machinery (2006/42/EC)

Applicable Harmonized Standards: EN 609-1:1999 +A2

ZEK 01.4-08/11.11

14

Name of Company: TIYA International Co., Ltd.

Address: B12B, Shenye Center, 9 Shandong Road,

Qingdao, China

Tel: (532) 8582 3333

Fax: (532) 8582 4444

Name / Title: Yuan Yue/ Director

Singautre:

Place / Date: Qingdao, China / Oct. 23, 2012



For more information on the Mitox® range of garden products please visit our website:

www.mitoxgm.co.uk


15


16

•

•

•

•

•

CONDITIONS OF WARRANTY

The manufacturer warrants the product against faulty materials and workmanship for a period of 2 years from the date of first purchase. The warranty is applicable when the product is used in a “home owner” application. If products are used for commercial or professional purposes, the warranty period is for 3 months from the date of first purchase. Warranty does not extend to failure due to fair wear and tear.

The manufacturer undertakes to replace any spare parts that are classified as defective by an appointed

Mitox service dealer. The manufacturer will not accept liability for the replacement of the machine, either partially or wholly, and/or consequential damages, and/or interest charges either directly or indirectly.

Warranty does not cover failure due to:

Insufficient maintenance.

Incorrect fuel or stale fuel.

Abnormal use or accidental damage.

Incorrect assembly, adjustment or operation of the product.

Spare parts that are subject to wear e.g. safety parts, blades, blade supports, bearings, cables, guards, deflectors, spark plugs, air filters etc.

•

•

•

•

Neither does warranty extend to:

Freight and packing costs.

Use of non-genuine spare parts i.e. those from another manufacturer.

Use of the machine for any other purpose than that for which it was designed.

Use and maintenance of the machine in a manner not described in the owner’s manual.

As part of our policy of continuous product improvement, we reserve the right to alter or amend this specification without notice. As a result, the product may differ from the information contained herein, but any alteration will only be implemented without notice if it is classified as an improvement to the above specification.

READ THE MANUAL CAREFULLY BEFORE OPERATING THE MACHINE

When ordering spare parts, please quote the part number, this can be found in the parts list included in this manual.

Retain the receipt of purchase without which no warranty can be offered.

Distributed by Mitox Garden Machinery

Wincanton Business Park

Wincanton

Somerset

BA9 9RS

www.mitoxgm.co.uk


User manual | Mitox LS700BS Operator`s manual

www.mitoxgm.co.uk

Operator’s Manual

LS700BS 7 Ton Petrol Logsplitter

SAFETY WARNINGS & EXPLANATION OF SYMBOLS ON THE MACHINE

E

A

EC Declaration of Conformity

We herewith declare

www.mitoxgm.co.uk

Related manuals

Table of contents

User manual | Mitox LS700BS Operator`s manual

www.mitoxgm.co.uk

Operator’s Manual

LS700BS 7 Ton Petrol Logsplitter

SAFETY WARNINGS & EXPLANATION OF SYMBOLS ON THE MACHINE

E

A

EC Declaration of Conformity

We herewith declare

www.mitoxgm.co.uk

Related manuals

ADENDORFF

VLS8TS-1

VARI

65715

Anova

51871 Electric log splitter

VARI

10 TON SUPER FORCE

Table of contents