Univers by FTE U4123E Installation guide

U4123E
The lightning flash with
arrowhead symbol, within
an equilateral triangle, is
intended to alert the user
to “dangerous voltage”
and to prevent from a
risk of electric shock.
Warning:
To reduce the risk of electric shock,
don’t open the cabinet. Refer servicing
to qualified personnel only.
The exclamation point
within an equilateral
triangle is intended
to alert the user to
important operating and
maintenance (servicing).
Please read the manual carefully before installing the receiver.
Caution: Never open the device by yourself. Dangerously high voltages are present inside the unit. Refer
servicing to qualified staff only.
When installing the receiver, always unplug the receiver from the mains voltage.
Unplug the receiver from the mains in case of long periods without operating the receiver (for example,
during holidays!).
To prevent shock hazard, do not touch the power plug with wet hands.
Always unplug the receiver before cleaning it or working on the connections.
Do not install the receiver close to strong heat sources, and ensure a good aeration if you plan to install
the receiver in a small cabinet.
Before you start operating the receiver, make sure that the satellite antenna is properly built up, optimally
connected and aligned.
The correct place to install the receiver is, of course, near your TV set and any other A/V signal sources
(DVD, VCR, CD, game console, etc.).
Choose a stable support, in which you can easily lay the necessary connecting cables without stumblingdanger.
The receiver should be installed near an easily accessible outlet.
Do not install the receiver in a place where it can be reached by liquid spills.
Do not put any heavy objects as, for example, a TV-device over the receiver; the receiver could be
damaged.
DO NOT INSTALL THE RECEIVER:
- On an unstable surface
- Subject to direct sunlight
- In high humidity environment
- Outside the receiver’s temperature range (+5°...+40°C)
If the receiver is subject to severe temperature changes, it can suffer from water condensation inside.
Switch off the receiver in these cases for at least 2 hours before resuming operation.
rev 1.0
English
SAFETY PRECAUTION
PAG. 2
QUICK INSTALLATION GUIDE
QUICK INSTALLATION GUIDE
Follow next steps for the correct installation of this receiver.
STEP 1: CONNECTIONS
Example 1 – Basic System
rev 1.0
Example 2 – DISEqC switches
Example 3 – Combined with terrestrial
PAG. 3
Example 4 – Motorized system
English
The coaxial cable, with satellite signal, must be connected to the “IF IN” connector. The “TV SCART” or
“HDMI” connectors must be connected to the TV set.
The receiver also includes an UHF modulator, allowing connecting a TV set or VCR. However the picture
quality will be a little poorer. The modulator has an antenna input and the output range is from channel
21 to 69. This will allow you to mix the existing antenna signals with the output channel generated by
the receiver.
The modulator output is factory preset to channel 38. You can change the output channel in the TV
system menu that you can find in System Setup menu.
You will also have to tune your TV set accordingly, in order to receive the picture from the receiver.
Depending on the type of installation, the receiver should be connected and configured following next
examples.
QUICK INSTALLATION GUIDE
STEP 2: BASIC CONFIGURATION OF THE
RECEIVER
Language: press [
] to select languages. The selection
of languages include: English, German, French, Spanish,
Italian, Portuguese, Turkish, Polish, Russian, Danish, Greek,
Hungarian, Arabic, Farsi.
First Audio: Some channels offer more than one audio language.
This function allows you to set the preferred audio language for
those channels using [
]. If a channel offers the same
audio language as the “First Audio” you set the system will play
this audio language as default. If the channel does not offer
this audio language then the system will compare the offered
languages with the second audio language. The selections of
audio languages include: English, German, French, Spanish,
Italian, Portuguese, Turkish, Polish, Russian, Danish, Greek,
Hungarian, Arabic, Farsi.
Second Audio: If the channel has no audio language that
corresponds with “First Audio” but with “Second Audio” the
system will play the second audio language as default. If no
audio language corresponds with the “Second Audio” then the
default language of the current channel will be played instead.
The selections of audio languages include: English, German,
French, Spanish, Italian, Portuguese, Turkish, Polish, Russian,
Danish, Greek, Hungarian, Arabic, Farsi.
LNB Power: Here you can set the power output to the LNB. If
your receiver is connected to the LNB directly then you need to
set the LNB Power to “On”. If your receiver is connected to a
multi switch (SMATV signal distribution system) then it may be
that you don’t need to provide the power to the LNB. But since
this is depending on the kind of installed distribution system we
recommend you to contact your installer or to refer to the user
PAG. 4
rev 1.0
English
IMAGE 1
The receiver includes an installation assistant (Quick Setup)
that will help you to setup the different parameters.
When the receiver is turned on at first time (using the button at
the rear panel of the receiver), the next menu is shown on the
TV (Image 1):
The receiver is programmed with all the channels of Astra (at
position 1 of the DISEqC), Hotbird (at position 2 of the DISEqC),
Hispasat (at position 3 of the DISEqC) and Turksat (at position
4 of the DISEqC). If your installation is different to this case,
please follow installation steps to search the channels.
In order to move through the different options of this menu,
] of your remote control. If a “Short
please use the keys [
circuit on the LNB” message is shown on the TV, please check
the connections before continuing the installation.
QUICK INSTALLATION GUIDE
manual of this system to get the correct information.
Single search: You can edit the following items (Image 2):
IMAGE 3
PAG. 5
English
rev 1.0
IMAGE 2
1. Satellite: Press [
] to switch Satellites or press [OK] to
enter satellite list to select directly.
2. LNB Configuration: Selecting this option and pressing [OK],
the LNB Configuration menu will be displayed. In this menu,
next options can be modified (Image 3):
] to switch among “Standard”, “User”
- LNB Type: Press [
and “Universal” mode. If you select “Standard” or “User”, the
frequency of the LNB can be changed. Pressing [OK] the
frequencies will appear to be edited. Select the frequency
you want to edit and change the value with [
]
] to switch “ON” and “Off”. The 22 kHz sig- 22K: Use [
nal is used in KU Universal LNBs to change between low
band and high band. After choosing LNB type “Universal”
you cannot modify 22K.
- DiSEqC1.0: Use [
] to switch the options of DiSEqC
switches.
] to switch the options of DiSEqC1.1
- DiSEqC1.1: Use [
switches.
- Positioner: Press [
] to select between “None /
DiSEqC1.2 / USALS”.
] to switch between “Auto / H / V”.
- Polarity: Press [
- Toneburst: Press [
] to switch this function “On” or
“Off”.
Once the LNB is configured, press [Exit] to save the changes and go to the previous window to continue configuring
the antenna.
3. DiSEqC1.0: Use [
] to switch the options of DiSEqC
switches.
4. On “TP Index” item use [
] to select the desired
transponder.
5. In the “FTA Only” item, press [
to select to scan only
free channels or even scrambled channels. If you select “Yes” it
will scan free channels only.
6. In “Scan Channel” item, press [
] to select to scan TV
+ Radio Channels, or just TV channels or just Radio channels.
7. In “Scan Mode” item you can select “Auto Scan” to blind
scan or “Preset Scan” to scan all preset transponders.
8. Move the highlight to “Search” and press [OK] button to
start scanning. Bars are showing the progress of the channel
scanning in the lower part of the window and the found channels
are listed.
You can stop the scan with [Exit] and save the so far found
channels.
9. Press [Exit] to exit this menu. A window to confirm the
changes will appear.
QUICK INSTALLATION GUIDE
English
IMAGE 4
Multi search: You can edit the following items (Image 4):
1. On “Satellite” item press [OK] to open the satellite list.
Then press [
] to move the highlight and press [OK]
to mark/unmark and [EXIT] to finish the selection. You can
select several satellites in this menu. At the bottom of the
screen you can see the selected satellites. The system will use
DiSEqC1.0/1.1, DiSEqC1.2 and USALS functions to search
the marked satellites and scan channels.
2. On “FTA Only” item, press [
] to select scanning of all
channels or just scanning of free channels. If you select “Yes” it
will scan free channels only.
3. On “Scan Channel” item, press [
] to select the
scanning range from TV + Radio Channels, only TV channels or
only Radio channels.
4. On “Scan Mode” item, you can select “Auto Scan” to make
a blind scan or “Preset Scan” to scan all preset transponders of
the selected satellites.
5. Select “Search” and press [OK] to start scanning. In the
lower part of the window the progress of scanning and the
found channels are displayed.
6. Press [Exit] to cancel or finish the scanning and saving the
found channels.
Main Menu: Selecting this option, the main menu will appear
on the TV.
STEP 3: TIME CONFIGURATION
IMAGE 5
Press the [Menu] key of the remote control for appearing the
main menu. Select the “System Setup” option and confirm
pressing [OK].
Once in the “System Setup” option, please select “Local Time
setting” option and press [OK]. Select “Time” option and press
[OK]. Image 5 is watched on the TV. For setting up the time,
please complete:
1. GMT Usage: this option will allow you to select if the date
and time will be introduced manually (GMT Usage: Off) or if
you wish to introduce the offset respect GMT manually (GMT
Usage: On).
2. GMT Offset: If GMT Usage is On, the offset respect GMT
has to be configured depending on your region or country. Use
the [
] keys to choose the offset. Remember that the
offset values are between -12:00 and +12:00
3. Summer: this option is only available when “USE GMT” is
enabled. Use [
] to switch on/off the summer timetable.
4. Date / Time: In order to introduce manually the time and
PAG. 6
rev 1.0
It is recommended to setup the clock before starting to enjoy
the receiver, because correct time maybe is required by some
applications. Please complete following options:
QUICK INSTALLATION GUIDE
date. Before these values can be modified, the automatic
control of GMT has to be turned off.
STEP 4: MODULATOR OUTPUT CHANNEL CONFIGURATION
IMAGE 6
It is recommended to setup the modulator output channel before starting to enjoy the receiver, especially if you are using this
output for getting the picture on the TV and mixing it with an
existing antenna signals.
The receiver includes an UHF modulator, allowing connecting
a TV set or VCR without SCART connector. The modulator has
an antenna input and the output range is from channel 21 to
69. This will allow you to mix the existing antenna signals with
the output channel generated by the receiver. The modulator
output is factory preset to channel 38. To change this value,
please complete following options:
rev 1.0
1. Press [Menu] button and access “System Setup” menu.
2. Select “TV System” menu and press [OK] (Image 6).
3. Select “RF Channel” option and change its value using
[
].
4. Press [Exit] button to save the changes and exit this menu.
You will also have to tune your TV set accordingly, in order to
receive the picture from the receiver.
PAG. 7
English
NOTE: If the current channel provides the correct time
information, you will see the current time after you entered
“Time” menu. If the channel doesn’t provide time information,
you have to input the date and time information manually. The
most channels support the time signal.
5. Show time: Use [
] to switch on/off this option. When
the option is enabled, the time will be displayed at the TV in a
frame in the top right margin.
6. Press [Exit] to exit the menu.
QUICK INSTALLATION GUIDE
TV Channel List: This option shows the list of TV stored channels.
Radio Channel List: This option shows the list of Radio stored channels.
Channel Setup: This option allows setting the receiver to start in a predefined channel.
Delete All: This option deletes all TV and Radio stored channels.
Restore channel list and settings: This option loads the user TV and Radio channel list,
saved previously.
Save channel list and settings: This option makes a backup of the channel list and it will
allow restoring the channel list even thought after a factory default.
Single Search: Once the antenna is configured, this option allows search for the channels
of one satellite.
Multi Search: Once the antenna is configured, this option allows search for the channels
of various satellites.
TP Search: Once the antenna is configured, this option allows search for the channels
of one TP.
Satellite List: This option shows all the stored satellites. This list can be modified.
Satellite Guide: After introducing some data, this application allows to know which
orientation and elevation should be the antenna.
rev 1.0
English
Favourite Channel List Name: It allows changing the name of the favourite groups.
PAG. 8
QUICK INSTALLATION GUIDE
Language: This option allows choosing the language of the menus.
TV System: This option allows choosing the video Standard and other parameters of
the screen.
Time & Timer Setting: Timer setting menu.
OSD Setting: This option allows configuring the subtitles of the channel information.
LNB Power: Turns on or off the LNB power.
RCU position Switch: To chose the RCU position of the remote control.
Information: Shows all the technical information for the selected channel.
Quick Setup: The installation assistant will be loaded.
Game: Some games like Tetris, Snake and Othello.
Factory Default: This option resets the receiver and loads the factory default values.
Software Upgrade: To update the receiver with other receiver, by USB or by satellite.
SatcoDX Auto programming: To load SatcoDX channel lists.
Smartcard: Information about conditional access system.
Media List: Allows to reproduce, to block and to delete recordings. Multimedia Player.
Media Control: Allows to configure the hard disk options and to format it.
rev 1.0
Disk Information: You can see the capacity of the hard disk.
Upgrade: To upgrade the receiver through the USB Port.
PAG. 9
English
Parental Lock: In this option, user can lock the access to the menu and change the
password of the receiver.
INDEX
Safety Precaution
Caution…..…………………...............................………………………………………………13
2. Basic Operations
2.0. Switch on STB……………………….....................................………………………………...16
2.1. Standby ……………………..............................................…………………………………...16
2.2. TTX …………..................................................……………………………………..16
2.3. Mute……………............................................………………………………………..16
2.4. Channel Number…………...........................……………………………………………………17
2.5. Multi-Pictures……............................……………………………………………………………17
2.6. CH + / CH -…...............................................…………………….…………………………..17
2.7. TV/RADIO…………........................…………………………………………………….17
2.8. Vol+/Vol-…......................................……………………………………………………….17
2.9. Exit….................................……………………………………………………..17
2.10. Menu-……………………...................................…………………………………..17
2.11. Recall…..............................................………………………………………...17
2.12. Channel List…………………….........................…………………………………...17
2.13. EPG…………………...............................…………………………………………...18
2.14. List………………................................…………………………………………………19
2.15. Favourites………....................................………………………………………………...19
2.16. Audio Track / Mode…...........................……………………………………………….19
2.17. Information……..................................…………………………………………...19
2.18. FAV +/-…..................................……………………………………………….19
2.19. ZOOM……………………………………………………………………...19
2.20. Subtitles……………………………………………………………………...20
2.21. LNB Short……………………………………………………………………...20
2.22. Code......................................................................................................20
2.23. REC......................................................................................................20
2.24. PVR......................................................................................................21
2.25. Time Shift......................................................................................................21
2.26. Forward / Reward ...................................................................................21
2.27. GoTo......................................................................................................22
3. Channel
3.1. TV Channel List…………....................……………………………………………..23
3.1.1. Favourite………...............................………………………………….……………23
3.1.2. Move.……………..............................………… …………………………….…………24
3.1.3. Sort......................................………………………… …………………….………..24
3.1.4. Edit….......................................…………………………………………….24
PAG. 10
rev 1.0
English
1. Panel & Remote Control Description
1.1. Front Panel Description…….......................................…………………………14
1.2. Rear Panel Description……................................………….…………………..14
1.3. Remote Control Description…...............................................…………………………..15
INDEX
4. Installation
4.1. Single Search…………......................……………………..…………………..28
4.2. Multi Search………...........................…………...………..…………………….29
4.3. TP Scan………..………………................………………………..…………………...30
4.4. Satellite List………….............................………………………...………………...31
4.5. Satellite Guide…………..................…………………………..………………...31
rev 1.0
5. System Setup
5.1. Language………………….............………………………...…………………...32
5.2. TV System……………..............…………………………..…………………...33
5.3. Time & Timer Setting ………....................………………………...………………33
5.3.1. Timer.......................................................................................33
5.3.2. Local Time setting...........................................................................35
5.3.3. Sleep Timer.................................................................................36
5.4. OSD Setting…………………………………......................…………………...36
5.5. Parental Lock…………………………............................…………………………….36
5.6. LNB Power…………………………………..............................……………………………..37
5.7. RCU Position Switch………………………………….....................……………………..37
6. Tools
6.1. Information…………………………...................................………………………….38
6.2. Quick Setup………………………………......................……………………...38
6.3. Game…………………………………………….......................……………………….39
6.3.1. Tetris..........................................................................................39
6.3.2. Snake...................................................................................39
6.3.3. Othello.........................................................................................39
6.4. Factory Default………………………………………..………………..............................39
6.5. Software Update………………………….………………………............................40
6.5.1. RS232 Upgrade...................................................................40
6.5.2. Upgrade by Satellite...................................................................40
PAG. 11
English
3.1.4.1 Delete…........................................…………….…...24
3.1.4.2 Skip….......................…………………………………..…………..24
3.1.4.3 Lock..….................................………………………… …….……….25
3.1.4.4 Edit..........................…………………...………………………...25
3.1.5. Find…………….........................……………………..……..………………..…….25
3.2. Radio Channel List……..................................……………………………………......26
3.3 Channel Setup…………..................................………………………………......26
3.3.1. Start-up Channel……………................................……………………………......26
3.3.2. Channel Play Type………........................…………………………………......26
3.4. Favourite Channel List Name……..........……………………………………......26
3.5. Delete All……...............…………….................………………………………….27
3.6. Restore channel list and settings………………..........…………………………………….27
3.7. Save channel list and settings………………..........…………………………………….27
INDEX
7. DVR Management
7.1. Media management.............................................................................................42
7.1.1. Recording management.............................................................................43
7.1.1.1. How to reproduce a recording..................…………..……………43
7.1.1.2. How to rename a recording.................……………………………43
7.1.1.3. How to block a recording………….........…………………………43
7.1.1.4. How to delete a recording..................……………………………43
7.1.1.5. How to delete all recordings..................…………………………44
7.1.2. Multimedia player.............................................................................44
7.1.2.1. Edit files and folders................................…………..……………44
7.1.2.2. Addind a new file to the list.................……………………………45
7.1.2.3. Search for file………….........………………………................46
7.1.2.4. Logo.............................................……………………………46
7.1.2.5. Configure the slide show.....................…………………………46
7.1.2.6. Audio .MP3 player…………....………………………................46
7.1.2.7. Picture .JPG viewer.............................................…………….47
7.1.2.8. Video .MPG player.....................………………..........………47
7.2. HDD Control..............................................................................................47
7.2.1. TMS Reserved Size.............................………………………………47
7.2.2. Jump Step Value............................……………………………………47
7.2.3. Record Type........................................………………………………47
7.2.4. Test Disk Speed............................……………………………………47
7.2.5. Record path..........………….............……….........…………………48
7.2.6. Format HDD..........………….............……….........…………………48
7.3. HDD Information........................................................................................48
7.4. Upgrading through USB........................................................................................48
8. Technical Specification……………………………………........................................49
9. Conformity declaration……………………………………........................................50
rev 1.0
English
6.5.3. Upgrade by USB...................................................................40
6.6. SatcoDX Auto Programming………………………...................................41
6.7. Smartcard........................………………..…………………….......................................…....41
PAG. 12
SAFETY PRECAUTION
Warning:
To reduce the risk of electric shock,
don’t open the cabinet. Refer servicing
to qualified personnel only.
The exclamation point
within an equilateral
triangle is intended
to alert the user to
important operating and
maintenance (servicing).
Please read the manual carefully before installing the receiver.
Caution: Never open the device by yourself. Dangerously high voltages are present inside the unit. Refer
servicing to qualified staff only.
When installing the receiver, always unplug the receiver from the mains voltage.
Unplug the receiver from the mains in case of long periods without operating the receiver (for example,
during holidays!).
To prevent shock hazard, do not touch the power plug with wet hands.
Always unplug the receiver before cleaning it or working on the connections.
Do not install the receiver close to strong heat sources, and ensure a good aeration if you plan to install
the receiver in a small cabinet.
Before you start operating the receiver, make sure that the satellite antenna is properly built up, optimally
connected and aligned.
The correct place to install the receiver is, of course, near your TV set and any other A/V signal sources
(DVD, VCR, CD, game console, etc.).
Choose a stable support, in which you can easily lay the necessary connecting cables without stumblingdanger.
The receiver should be installed near an easily accessible outlet.
Do not install the receiver in a place where it can be reached by liquid spills.
Do not put any heavy objects as, for example, a TV-device over the receiver; the receiver could be
damaged.
DO NOT INSTALL THE RECEIVER:
- On an unstable surface
- Subject to direct sunlight
- In high humidity environment
- Outside the receiver’s temperature range (+5°...+40°C)
rev 1.0
If the receiver is subject to severe temperature changes, it can suffer from water condensation inside.
Switch off the receiver in these cases for at least 2 hours before resuming operation.
PAG. 13
English
The lightning flash with
arrowhead symbol, within
an equilateral triangle, is
intended to alert the user
to “dangerous voltage”
and to prevent from a
risk of electric shock.
PANEL & REMOTE CONTROL DESCRIPTION
1. PANEL & REMOTE CONTROL DESCRIPTION
4 8 7
1
23
5
6
1. POWER: Switches the receiver on, or enters standby mode. To completely switch off the receiver,
you have to use the switch on the back of the receiver.
2. LOCK LED: Indicates a sufficient signal level at the IF IN input.
3. POWER LED: Indicates that the mains voltage (90-230 VAC) is available.
4. DISPLAY: 4 Digits to display the program numbers.
5. IR-SENSOR: Reception sensor for the IR remote control signals.
6. CH+/-: These buttons allow changing the current channel.
7. Conditional Access: FELEC-CAS
8. USB: Connector for external USB 2.0 HighSpeed devices.
1.2. REAR PANEL DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
1. IF IN: Satellite input.
2. VIDEO / AUDIO: HiFi Outputs for stereo set or monitor
3. OPTICAL S/PDIF: Optical output for digital audio (AC3).
4. TO TV: Modulator output for the connection to a TV set.
5. ANT IN: Antenna input for the terrestrial antenna.
6. RS-232: Serial Port allowing software upgrades.
7. AC IN: Mains input cable.
8. POWER ON/OFF: Allows to completely switching off the receiver.
9. HDMI: HDMI Output
Note: If you have the HDMI output connected and you select the progressive mode, the SCART
output is automatically disabled.
10. IF OUT: Satellite output for cascading to other devices.
Note: The operation of another receiver at the same time is only possible with limited channel
selection.
11. TV SCART: Output SCART for the connection to a TV set.
12. VCR SCART: Output SCART for the connection to a VCR set.
13. COAXIAL S/PDIF: Coaxial output for digital audio (AC3).
PAG. 14
rev 1.0
English
1.1. FRONT PANEL DESCRIPTION
PANEL & REMOTE CONTROL DESCRIPTION
1
3
6
8
10
16
17
19
22
21
26
25
29
30
33
7
9
12
11
13
15
18
20
23
24
27
28
31
32
34
35
■
rev 1.0
■
PAG. 15
English
14
2
4
5
1.- POWER: Switches receiver ON or in stand-by-mode.
2.- LEDs: Shines as function control, showing the selected
transmission code 1, 2 or 3.
3.- TV/R: Switches between TV and Radio channels.
4.- CODE: Changes transmission code of the remote control.
5.- MUTE: Switches audio on and off.
6.- NUMERIC KEYS: For direct typing values and names.
7.- “0”
8.- INFO: Shows channel information with signal bar.
9.-Audio: Opens audio menu.
10.- VOL+ / VOL-: Adjusts audio volume up and down.
11.- CH+ / CH-: Changes channel up and down.
12.- Back: To toggle between the actual and the last selected
channel.
13.- EXIT: Exit menus or stop operations.
14.- EPG: Shows the EPG information.
15.- MENU: Opens the main menu.
16.: Adjusts audio volume or controls the cursor in
menus.
17.: Changes channels volume or controls the cursor in menus.
18.- OK: Confirms selections or opens channel list.
19.- REC: Quick start for recording.
20.- PVR: Opens PVR menu.
21.- ►II : Start / Stop button for recording and TimeShift.
22.- ■ : Stop button for recording and TimeShift.
23.: Backward button for recording and TimeShift.
24.- ■ : Forward button for recording and TimeShift.
25.: Back.
■
26.: Next.
27.- GoTo: To move to the specified position.
28.- Fav: Opens favourite channel list.
29.- List: Opens channel list.
30.- Pup / Pdw: Moves cursor in block steps.
31.- Sub: Switches subtitle on and off.
32.- Fav+ / Fav-: Moves favourite channel up and down.
33.- TEXT: Opens and closes teletext.
34.- Zoom: Zoom function.
35.- Color keys: Controls menu options.
BASIC OPERATIONS
2. BASIC OPERATIONS
2.0. SWITCH ON STB
English
Switch the [Device’s Main Power] switch on.
When the STB is first used it will display the quick setup page
where the receiver can be configured quickly.
For further use the STB will play the same channel as last time
when it was switched off.
OSD 1
OSD 2
? FREQUENTLY ASKED QUESTION
Q: The power of my STB is on and it is running in TV mode but
the TV screen shows nothing:
A: Make sure the TV set has been set to the correct video input
(not the TV channels). For example, if you have connected the
STB to the Video1 input of the TV set, then you need to select
the corresponding Input on the TV. Mostly it is done with the AV
button of the TVs remote control unit.
Q: My STB is running in TV mode but the TV screen shows
nothing except one ball and “No Signal”.
A: That means the channel you selected has no signal. This can
be caused by several reasons:
1. The channel you selected is not from the satellite to which
your dish is pointing. Select another channel.
2. The signal of current TV channel is too weak. You can
try to change to other channels with a stronger signal. If the
problems still exist, please consult your local dealer or installer
for technical service.
3. You selected the wrong LNB type in the installation menu or
your DiSEqC switch configuration is not correct.
2.1. STANDBY
1. Press [Power] button to switch from TV mode to Standby
mode.
2. In Standby mode press [Power] button again to switch back
to TV mode. The last active channel will be showed.
3. To switch off the STB complete press the main power button
(placed at the rear panel of the receiver).
2.2. TTX
2.3. MUTE
1. Press the [Mute] button to mute the sound. On the screen an
icon will be displayed to indicate the muted sound (OSD 2).
PAG. 16
rev 1.0
OSD 3
1. Press [TXT] button in TV mode to open the teletext page
(OSD 1). This service is depending on the support of the
channel provider.
2. If the channel does not support teletext information, it will
show “No Teletext Data” on the screen.
BASIC OPERATIONS
2. Press the [Mute] button again to restore the sound.
2.4. CHANNEL NUMBER
In TV mode you can enter the channel number directly with your
remote control unit and confirm the number with the OK button
to change to the desired channel.
2.5. MULTI-PICTURES
2.6. CH +/ CH In TV mode press [CH+/CH-] to change channel.
2.7. TV/RADIO
OSD 5
In TV mode, press [TV/R] to switch to Radio mode. In Radio
mode press [TV/R] again to switch back to TV mode.
2.8. VOL+/VOLIn TV mode, press [Vol+/Vol-] to adjust volume.
2.9. EXIT
Press [Exit] button to exit the current menu.
2.10. MENU
Press [Menu] button to enter or exit the current menu.
2.11. RECALL
Pressing the [Back] button allows you to toggle between the
actual and the last selected channel.
rev 1.0
OSD 6
2.12. CHANNEL LIST
In TV mode press [OK] button to open the Channel List
window.
PAG. 17
English
OSD 4
In TV mode, press [0] button to enter the Multi-Picture mode
(OSD 3).
1. In Multi-Picture mode the screen will display 9 channels’
preview window (static), starting from the current channel. Only
the marked preview program is continuously playing.
2. Press [
] to change the marked channel among
the preview programs.
3. With the number buttons [1] ~ [9] you can directly move the
highlight to the related channel.
4. With [OK] you return to full screen mode in the marked
channel.
BASIC OPERATIONS
English
OSD 7
OSD 8
Reduced Channel List (OSD 4):
You can use [
] keys to navigate this list.
1. Press [Yellow] button to open the SAT list. After selecting a
satellite the channel list will be reduced to the channels of this
satellite.
2. Press [Blue] button to open the “Find” window. You can use
this feature to find channel by their names.
3. Press [Red] button to open the expanded channel list.
4. Once the desired channel is selected, press [OK[ to change
and display the marked channel.
Expanded Channel List (OSD 5):
] keys to navigate this list.
You can use [
In this view, you can get more information about the frequency,
polarity, symbol rate and PID of the selected channel.
1. Press [Green] button to sort the channels by free and
scrambled channels. Free channel are listed first and scrambled
channels last.
2. Press [Yellow] button to open the SAT list. After selecting a
satellite the channel list will be reduced to the channels of this
satellite.
3. Press [FAV] button to open FAV list. After selecting a
Favourite Group the channel list will be reduced to the channels
of this group.
4. Press [Blue] button to open the “Find” window (OSD 6). You
can use this feature to find channel by their names.
5. Press [Red] button to open the reduced channel list.
6. Once the desired channel is selected, press [OK[ to change
and display the marked channel.
OSD 9
OSD 10
1. The STB supports Electronic Program Guides (EPG) to give
you information about the actual programs of certain channels
like event name, subtitle, description, start and finish time. This
feature is depending on the service of the channel provider.
Press [EPG] to open the EPG window (OSD 7).
2. The [Red] button opens the detailed schedule of the marked
channel (OSD 8). You can select an event with [
] and
display the event’s detailed description with [OK]. With the
[Yellow] button you can program a timer with the start and finish
time and date of this event.
3. Press the [Green] button in the EPG menu to display the
detailed information of the actual event in the selected channel
(OSD 9). With the [Red] button you can get more information
about the events of the channel. With the [Yellow] button you
can program a timer with the start and finish time and date of
this event.
4. To close the EPG menu press [Exit].
OSD 11
PAG. 18
rev 1.0
2.13. EPG
BASIC OPERATIONS
2.14. LIST
In TV mode, press [List] button to access directly to the “TV
Channel List” menu or to the “Radio Channel List” menu.
2.15. FAVOURITES
OSD 12
? FREQUENTLY ASKED QUESTION
Q: Why the screen displays “No Favourite Channel” after
pressing the [Favourite] button?
A: No channels have been assigned to a Favourite Group yet.
You can do this in the channel menu.
2.16. AUDIO TRACK / MODE
1. In TV mode, press the [Audio] button to open the Audio
Mode window (OSD 11).
2. Select the item you want to adjust with [
] and change
].
the value with [
3. Press [Exit] to leave this window.
2.17. INFORMATION
In TV mode, press [INFO] button can open information screen
(OSD 12), in the window shows the parameters of current
channel.
2.18. FAV +/1. In TV mode press the [FAV+/FAV-] buttons to switch
between the favourites channels in the current Favourite Group
directly.
2. The sequence of the favourite channels is following the
sequence in the related Favourite Group list.
2.19. ZOOM
rev 1.0
1. Press [Zoom] button in TV mode to zoom the image. Image
can be augmented x16 times (OSD 13).
2. Press [Exit] to exit this function.
OSD 13
PAG. 19
English
1. In TV mode press the [Favourite] button to display the
Favourite Group window on the screen as the picture beside
shows (OSD 10).
2. In the Favourite Group window you can select the desired
favourite channel with [
] and confirm it with [OK] to switch
to it. In bigger groups you can navigate with [Pup/Pdw].
] you can select different Favourite Group.
3. With [
4. Press [Exit] to close the Favourite Group window.
BASIC OPERATIONS
2.20. SUBTITLES
In TV mode, press [Sub] button for activating / deactivating the
channel subtitles, depending on the provider information.
OSD 14
2.21. LNB SHORT
When LNB is short, it will notify user on screen “LNB Short!”
(OSD 14). Please check your cables and connections for
shorts. When the short is removed the warning message will
disappear.
English
2.22 CODE
It shows and changes the selected code on the remote control.
This code has to correspond with the one selected on the
receiver’s menu. (Chapter 5.7)
2.23. REC
Note: If the hard disk is full, a warning message will be shown
on the screen. Please, delete some files in order to be able to
record again (chapter 7.1.1.4).
Note: If during the recording, the hard disk fills up, the recording
stops and will only store the data recorded until that moment
(without losing the previously stored data).
In case you execute a fast recording and fixing the duration, this
will get in conflict with a timer, an alert message will be shown
in the screen.
This message informs with the first timer that would be in
conflict in the fast recording, and it requests the confirmation
that you want to do in the moment of the timer.
- If you push again “Rec”: it will keep the event programmed.
The receiver will carry out the fast recording until the moment of
the programmed event, when it will do it, obviating the selected
duration in the fast recording.
PAG. 20
rev 1.0
OSD 15
To start the recording (OSD 15).
If you would like to record a programme immediately, press the
Key REC. A new window will appear on the screen, where you
can select the length of the recording (from 15 to 180 minutes
in a range of 15 minutes interval).
The rest of the data that appear in this window inform you about
the recording channel, the date, the time and the free space on
the hard disk. Once the minutes length is settled, confirm again
by pressing the REC key and it will start to record.
Press [Exit] to cancel the recording.
BASIC OPERATIONS
OSD 16
- If you push “Exit”: it will make the fast recording and will
obviate the temporised events that will get in conflict. Anyway,
in the moment of the temporised event the user are inquired
again about if he wants to carry out the programmed event. In
case of no response, it will continue with the fast recording.
In order to stop a recording before the ending of the programmed
length, press the [Stop]-Key. A new window will be shown in
order to confirm the end of the recording (OSD 16). If you
press the Key [Rec], the recording will continue. Press the key
[Stop] again to end the recording manually, if you want to end
the recording before the programmed length.
It opens directly the recording administration menu (Chapter
7.1).
2.25. TIME SHIFT
OSD 17
If you are watching a program and you want to stop it and
later continue watching it, press the key [ ►II ] on the remote
control. The program will stop and will be stored on the hard
disk of your receiver. The OSD will show you the time since the
function is activated (OSD 17).
When you wish to continue watching the program, press the
button [ ►II ] again. If the information is on the hard disk, it is
possible to fast forward and reward. Pressing the button [
] or [ ■ ] several times, you can settle the speed of forward.
Options: 2x, 4x y 8x.
You can also use the keys [
] or [ ■ ] in order to go
forward/reward.
Using the key [Info] you can see the time difference between
your reproduction and the real time.
In order to leave the Time Shift option, press the key [stop] to
equal the difference between the reproduction time with the
real one. When you press [Stop] again, it will appear a window
to ask for the confirmation to finish the Time Shift (OSD 18).
If you press the key [Rec], it will continue in Time Shift mode.
Press the key [Stop] again to leave the Time Shift settings.
■
■
rev 1.0
2.26. FORWARD / REWARD
On a current reproduction, press the keys [
] or [ ■ ] to
go forward or reward in a period of the reproduction.
This period is configurable using the receiver menu and they
can be of: 1, 3, 5, 10 and 15 minutes (chapter 7.2.2).
If it is configured in every 10 minutes, each time that you press
this key, it will jump automatically 10 minutes forward/reward
of the reproduction.
PAG. 21
■
OSD 18
English
2.24. PVR
BASIC OPERATIONS
2.27. GOTO
rev 1.0
English
OSD 19
On a current reproduction, press the key [GoTo] to go to a
certain point of the reproduction.
When you press this key, a window appears where you can
introduce, using the numbers on the remote control, the hour:
minute: second you want to go to (OSD 19).
If the introduced value is higher to the reproduction limit, an
error window will be shown.
PAG. 22
CHANNEL
3. CHANNEL
OSD 20
3.1. TV CHANNEL LIST
OSD 21
OSD 22
If you enter the Channel List menu a window like the one
besides will open (OSD 22).
1. You can move the highlighted channel with [
] and
press [OK] to preview the highlighted program in the preview
window.
2. You can enter directly the number of the desired channel with
the remote control. The selection will select that channel, but it
will not be previewed until you confirm with [OK] button.
3. Press [Pup/Pdw] on the RCU to jump between the channels
by pages.
4. Press [
] to switch the Program Group.
5. Press [Menu], [Exit] or [Ok] buttons to enter TV mode
playing mode.
6. The colour buttons offer further functions to manage the
channel list.
3.1.1. FAVOURITE
rev 1.0
1. Press [FAV] to open the Favourite window (OSD 23).
2. You can select between 8 favourites groups with [
].
Press [OK] to assign the channel to a Favourite group.
3. Press [OK] again to remove the channel from the marked
Favourite group.
4. Press [Exit] button to return to the TV Channel List. The
channels of Favourites Groups are indicated with a favourite
icon behind the name.
OSD 23
PAG. 23
English
Press [Menu] in the TV mode to enter the main menu (OSD
20).
] to select the Channel item.
1. Press [
2. Press [OK] to enter the selected item.
In the Channel menu (OSD 21):
3. Press [
] to select the wanted menu item.
4. Press [OK] to enter the selected item among.
- TV Channel List
- Radio Channel List
- Channel setup
- Favourite channel list name
- Delete All
- Restore channel list and settings
- Save channel list and settings
CHANNEL
3.1.2. MOVE
English
OSD 24
OSD 25
1. To move/change channels: Pushing the [Red] button, you
will see a picture like OSD 24. You will be able to move or
change the position of the channels:
- Push again the [Red] button to move the channel.
- Push the [Green] button to change the position of the
channel.
2. Move the channel to the desired position with [
].
Press [OK] to confirm the position.
3.1.3. SORT
1. Press [Green] to open the Sort window (OSD 25). Press [
] to select and [OK] to confirm your choice.
2. The ways of sorting are:
- Name (A-Z): Sorting in Alphabetical Order, ignoring “$” symbol.
- Name (Z-A): Sorting in Alphabetical Order, ignoring “$” symbol.
- FTA: Sort channel by free and scrambled sequence. Free
channels will be listed first and scrambled channels behind
in the channel list.
- Lock: Unlocked channels are listed first end locked channels
at the end.
- Default: Load the default sort of channels.
3.1.4. EDIT
OSD 26
1. After pressing the [Yellow] button a window for entering the
password will open. The default password is “0000”.
2. You can Delete, Skip, Lock and Edit the channel (OSD 26).
3. Press [Exit] to leave the Channel Editing. The system will ask
you to confirm the saving of the changes you made.
3.1.4.1 DELETE
OSD 28
OSD 29
3.1.4.2 SKIP
In Channel Edit menu, press [Green] button to place a Skip icon
behind the name of the highlighted channel. Marked channels
(OSD 29) will be skipped when you change channels in TV
PAG. 24
rev 1.0
OSD 27
In Channel Edit menu press [Red] button to mark a channel
for deleting.
A confirmation of deleting one or all channels from the list is
displayed (OSD 27):
- Please, confirm pushing the [Red] button to select the channels
one by one. Only the selected channels will be deleted.
- Confirm pushing the [green] button to select all the channels
from the list.
Marked channels (OSD 28) will be deleted after you confirm to
save the changes when you leave this menu.
CHANNEL
mode after you confirm to save the changes when you leave
this menu.
OSD 30
3.1.4.3 LOCK
In Channel Edit menu, press [Yellow] button to place a Lock icon
behind the name of the highlighted channel. Marked channels
(OSD 30) will be locked and displayed only after password has
been entered if you confirm to save the changes when you
leave this menu.
OSD 31
OSD 32
OSD 33
Pressing the [Blue] button in the TV Channel List Edit menu will
open another window where you can choose between Edit the
actual channel or create a new channel (OSD 31).
1. Edit current channel: To edit the channel press the [Red]
button (OSD 32).
- Name: You can edit the name of the current channel using the
keys on the remote control.
- On the “Video PID”, “Audio PID” and “PCR PID” items you can
input numbers to modify the item’s value.
- After modification select “Save” and press [OK] button to save
the modified values and exit “Edit” mode. Or select “Exit” and
press [OK] to leave Edit mode without saving the modifications.
2. Create: Press [Green] button to open the Create window
(OSD 33).
- Press [OK] button on the “Satellite” item to display the satellite list. You can select the satellite for which you want to create a new channel.
- With marked “TP Index” item press [
] to select the TP
number where the channel can be found. The next three items will show the related parameters.
- Highlight the “Name” item and edit the name of the current
channel using the keys on the remote control.
- In “Video PID”, “Audio PID” and “PCR PID” items you can
enter the numbers directly to set these parameters of the
new channel.
- After modification select “Save” and press [OK] to save the
new channel and leave the Edit mode. Select “Exit” and press
[OK] to exit the Edit mode without saving the new channel.
rev 1.0
3.1.5. FIND
OSD 34
1. Press [Blue] button to open the “Find” window like showed
besides (OSD 34). Press [
] to select the leading
character of the channel name and press [OK] to confirm it.
2. After entering the character(s) highlight “OK” in the window
and press [OK] on the RCU.
PAG. 25
English
3.1.4.4 EDIT
CHANNEL
3. Press [Exit] button to close the Find window and brings you
back to the channel list.
3.2. RADIO CHANNEL LIST
Basically the operation of “Radio Channel List” is same as “TV
Channel List” (OSD 35).
OSD 35
3.3. CHANNEL SETUP
English
When you enter the “Channel Setup” menu you will see a
screen like beside (OSD 36):
3.3.1. START-UP CHANNEL
OSD 36
OSD 37
Press [OK] to enter “Start-up Channel” menu to see the screen
like showed beside (OSD 37):
1. If you set of “Boot on Channel” to “On” you can edit the
following two items. If the setting is “Off” the box always starts
with the channel that was running when the box has been
switched off.
2. On the “Mode” item you can select either “TV channel” or
“Radio channel”.
3. On “Start-up Channel” item you can open the channel list by
pressing [OK]. Then you can select the channel of you choice.
Press [OK] again to confirm.
3.3.2. CHANNEL PLAY TYPE
Press [OK] to enter “Channel Play Type” menu (OSD 38).
1. Here you can select the “playing channels” as “Free”,
“Scrambled” or “All”.
2. If you select “Free” then all scrambled channels will be
skipped when you change channels with [CH+/-].
3. Press [Exit] to leave the “Channel Setup” menu.
3.4. FAVOURITE CHANNEL LIST NAME
In this menu, user is able to change the name of the Favourite
Groups. Press [OK] to enter this menu and you will see a
screen like beside (OSD 39).
To change the name of the Favourites Groups:
1. Press [
] and select a Favorite Group.
2. Press [Ok] button to edit the name of the Group.
3. Once the name is correct, select “Ok” option and confirm
pressing [OK] (OSD 40 next page).
4. If the name is used by other group, an alert message will
appear on the TV.
5. Select “Exit” and press [OK] to leave this menu.
rev 1.0
OSD 38
OSD 39
PAG. 26
CHANNEL
3.5. DELETE ALL
OSD 40
To delete all channels:
1. Enter the password. The default password is “0000”.
2. After entering the password correct a safety question will
show up where you have to confirm first (OSD 41).
3. Select “Yes” to delete all channels or “No” to cancel and
confirm with [OK].
4. In step 2 and step 3, pressing [Exit] will exit the function
directly without saving.
OSD 41
rev 1.0
OSD 42
OSD 43
3.6. RESTORE CHANNEL LIST AND SETTINGS
Using this option, the receiver will load the channels saved as
previously as a backup of the user channels list (see point 3.7.).
For restoring the default channels, please:
1. Enter the password. The default password is “0000”.
2. After entering the password correct a safety question will
show up where you have to confirm first (OSD 42).
3. Select “Yes” to delete all channels or “No” to cancel and
confirm with [OK].
4. In step 2 and step 3, pressing [Exit] will exit the function
directly without saving.
3.7 SAVE CHANNEL LIST AND SETTINGS
This option is very important, because here is where the security
of your data lies. This option makes a backup of the channel
list and it will allow restoring the channel list even thought after
a factory default.
Once you have customized your receiver and everything
operates properly, you have the possibility, with this option, to
save the programs’ data.
1. Enter the password. The default password is “0000”.
2. After entering the password correct a safety question will
show up where you have to confirm first (OSD 43).
3. Select “Yes” to delete all channels or “No” to cancel and
confirm with [OK].
4. In step 2 and step 3, pressing [Exit] will exit the function
directly without saving.
PAG. 27
English
? FREQUENTLY ASKED QUESTION
Q: IF I incautiously delete all channels, what should I do?
A: There are three ways to restore:
- To re-search all channels at the “Installation” menu.
- Use “Factory Default” function to restore all channels in the
“Tools” menu. The receiver will load the factory channels.
- Use the “Restore channel list and settings” option as next
point shows.
INSTALLATION
4. INSTALLATION
English
OSD 44
Press [Menu] in the TV mode to enter the main menu (OSD
44).
] to select the Installation item.
1. Press [
2. Press [OK] to enter the selected item.
In the Installation menu (OSD 45):
3. Press [
] to select the wanted menu item.
4. Press [OK] to enter the selected item among.
- Single Search
- Multi Search
- TP Scan
- Satellite List
- Satellite Guide
OSD 45
OSD 46
After selecting Antenna Setup another window will be opened
(OSD 46).
You can edit the following items:
1. Satellite: Press [
] to switch Satellites or press [OK] to
enter satellite list to select directly.
2. LNB Configuration: Selecting this option and pressing [OK],
the LNB Configuration menu will be displayed (OSD 41). In this
menu, next options can be modified:
- LNB Type: Press [
] to switch among “Standard”, “User”
and “Universal” mode. If you select “Standard” or “User”, the
frequency of the LNB can be changed. Pressing [OK] the
frequencies will appear to be edited. Select the frequency
you want to edit and change the value with [
]
- 22K: Use [
] to switch “ON” and “Off”. The 22 kHz signal is used in KU Universal LNBs to change between low
band and high band. After choosing LNB type “Universal”
you cannot modify 22K.
- DiSEqC1.0: Use [
] to switch the options of DiSEqC
switches.
- DiSEqC1.1: Use [
to switch the options of DiSEqC1.1
switches.
- Positioner: Press [
to select between “None /
DiSEqC1.2 / USALS”.
- Polarity: Press [
] to switch between “Auto / H / V”.
Once the LNB is configured, press [Exit] to save the changes
and go to the previous window to continue configuring the
antenna.
] to switch this function “On” or
- Toneburst: Press [
“Off”.
OSD 47
PAG. 28
rev 1.0
4.1. SINGLE SEARCH
INSTALLATION
OSD 48
4.2. MULTI SEARCH
OSD 49
rev 1.0
OSD 50
When you enter the “Multi Search” menu a window like the one
beside will open (OSD 49).
1. On “Satellite” item press [OK] to open the satellite list (OSD
50). Then press [
] to move the highlight and press [OK] to
mark/unmark and [EXIT] to finish the selection. You can select
several satellites in this menu. At the bottom of the screen you
can see the selected satellites (OSD 51). The system will use
DiSEqC1.0/1.1, DiSEqC1.2 and USALS functions to search
the marked satellites and scan channels.
2. On “FTA Only” item, press [
] to select scanning of all
channels or just scanning of free channels. If you select “Yes” it
will scan free channels only.
3. On “Scan Channel” item, press [
] to select the
scanning range from TV + Radio Channels, only TV channels or
only Radio channels.
4. On “Scan Mode” item, you can select “Auto Scan” to make
a blind scan or “Preset Scan” to scan all preset transponders of
the selected satellites.
5. Select “Search” and press [OK] to start scanning. In the
lower part of the window the progress of scanning and the
found channels are displayed.
6. Press [Exit] to cancel or finish the scanning and saving the
found channels.
OSD 51
PAG. 29
English
3. DiSEqC1.0: Use [
] to switch the options of DiSEqC
switches.
4. On “TP Index” item use [
] to select the desired
transponder.
] to select to scan only
5. In the “FTA Only” item, press [
free channels or even scrambled channels. If you select “Yes” it
will scan free channels only.
6. In “Scan Channel” item, press [
] to select to scan TV +
Radio Channels, or just TV channels or just Radio channels.
7. In “Scan Mode” item you can select “Auto Scan” to blind scan
or “Preset Scan” to scan all preset transponders.
8. Move the highlight to “Search” and press [OK] button to
start scanning. Bars are showing the progress of the channel
scanning in the lower part of the window and the found channels
are listed (OSD 48).
You can stop the scan with [Exit] and save the so far found
channels.
9. Press [Exit] to exit this menu. A window to confirm the
changes will appear.
INSTALLATION
English
OSD 52
OSD 53
OSD 54
OSD 55
When you enter “TP Scan” menu a window like the one beside
will be displayed (OSD 52):
] to select the satellite
1. On “Satellite” item, press [
you want to scan or press [OK] to open the satellite list for
selection.
2. On “TP Index” item use [
] to select the desired
transponder.
If any of the TP of the list have tuned and stored channels into
the receiver, the following two options “Frequency” and “Symbol
Rate” will not be able to be edited.
It means that the parameters cannot be modified by error
neither loosing the stored channels when any value of the data
base is changed.
In case of any value, for example the Symbol Rate of a TP,
has been modified by the provider and the receiver has these
channels tuned, the TP must be deleted (it will delete all the
channels of this TP), create it again with the correct data, and
to carry out a new search of the TP.
In this item you can also add, delete or delete all TP.
- Press [Red] button to add a new TP (OSD 53). You have to
set the parameters of “TP Frequency” and “Symbol Rate” for
this new transponder. Therefore use the number buttons of
the RCU. The available range are “3000~13450 MHz” and
“1000~45000KS/s”.
- Press [Green] button to delete the current TP. A safety question will be displayed for confirmation to delete the current
transponder or not (OSD 54). If you select “Yes”, the current
transponder will be deleted and the total number of transponders will be reduced.
- Press [Yellow] button to delete all TP. A safety question will be
displayed for confirmation to delete all transponders or not. If
you select “Yes”, all transponders will be deleted.
3. For transponders you also can use number buttons to modify
the parameters of “TP Frequency” and “Symbol Rate” or [
] to change the value directly. “Polarity” and “Scan Mode”
are used for setting scans conditions. Press [
] to select
a different mode.
4. Polarity: Press [
] to switch between “Auto / H / V”.
5. Search channels of the TP: Selecting this option, a new
window appears, where you can configure the following
parameters (OSD 55):
] to select scanning of all
- On “FTA Only” item, press [
channels or just scanning of free channels. If you select “Yes” it
will scan free channels only.
- On “Scan Channel” item, press [
] to select the scanning
range from TV + Radio Channels, only TV channels or only
Radio channels.
- Search NIT: If you select this option as “Off”, the receiver
PAG. 30
rev 1.0
4.3. TP SCAN
INSTALLATION
will search the selected TP. In case you select “On”, the NIT
(Network Identification) will be identified and the receiver will
automatically search all the TP of this network.
6. Press [OK] to start scanning.
7. On the “TP Scan” item, press [Exit] to cancel the scanning
and saving the found channels.
4.4. SATELLITE LIST
OSD 56
4.5. SATELLITE GUIDE
OSD 58
rev 1.0
OSD 59
When you enter “Satellite Guide” menu, you will see the screen
like beside (OSD 59).
Here you can enter your local longitude and latitude and the
satellite’s longitude. The receiver calculates the antenna’s
azimuth and elevation to point your antenna to the selected
satellite.
1. Use the [Number] buttons to input the values of “Local
Longitude”, “Local Latitude” and “Satellite Longitude”.
2. Press [
]buttons to select east or west in “Local
Longitude” and “Satellite Longitude” or to select north or south
in “Local Latitude”.
3. Highlight the “Start” item and press [OK]. In the lower part
of the window the corresponding values for the antenna setting
are displayed (OSD 60).
4. Orientation means the angle between south and satellite.
5. Press [Exit] to leave this feature
OSD 60
PAG. 31
English
OSD 57
When you enter the “Satellite List” menu you can see a window
like the one beside (OSD 56):
] and mark/
1. Move through the satellite list using [
unmark the satellites that you want pressing [OK]
2. Press [Red] button to enter edit satellite menu (OSD 57).
You can edit the satellite’s name and its longitude. Once you
have edited the satellite, select “Save” option and confirm with
[OK]. If you prefer to exit without saving the changes select
“Exit” and press [OK].
3. Press [Green] button to open the “Add satellite” window. You
can edit the satellite’s name and its longitude. Once you have
edited the satellite, select “Save” option and confirm with [OK].
If you prefer to exit without saving the changes select “Exit” and
press [OK].
4. After pressing [Yellow] button you will be asked “Are you
sure to delete?” (OSD 58). Select “Yes” to delete the marked
satellite. Select “No” to cancel the operation.
SYSTEM SETUP
5. SYSTEM SETUP
English
OSD 61
Press [Menu] in the TV mode to enter the main menu (OSD
61).
] to select the System Setup item.
1. Press [
2. Press [OK] to enter the selected item.
In the System Setup menu (OSD 62):
3. Press [
] to select the wanted menu item.
4. Press [OK] to enter the selected item among.
- Language
- TV System
- Time & Timer Setting
- OSD Setting
- Parental Lock
- LNB Power
- RCU Position Switch
5.1. LANGUAGE
rev 1.0
OSD 62
After selecting the “Language” menu you will see a window like
beside (OSD 63):
1. Language: press [
] to select languages. The selection
of languages include: English, German, French, Spanish,
Italian, Portuguese, Turkish, Polish, Russian, Danish, Greek,
Hungarian, Arabic, Farsi.
2. First Audio: Some channels offer more than one audio
language. This function allows you to set the preferred audio
language for those channels using [
]. If a channel offers
the same audio language as the “First Audio” you set the
system will play this audio language as default. If the channel
does not offer this audio language then the system will compare
the offered languages with the second audio language. The
selections of audio languages include: English, German,
French, Spanish, Italian, Portuguese, Turkish, Polish, Russian,
Danish, Greek, Hungarian, Arabic, Farsi.
3. Second Audio: If the channel has no audio language that
corresponds with “First Audio” but with “Second Audio” the
system will play the second audio language as default. If no
audio language corresponds with the “Second Audio” then the
default language of the current channel will be played instead.
The selections of audio languages include: English, German,
French, Spanish, Italian, Portuguese, Turkish, Polish, Russian,
Danish, Greek, Hungarian, Arabic, Farsi.
4. Press [Exit] to return back from “Language” menu.
OSD 63
PAG. 32
SYSTEM SETUP
5.2. TV SYSTEM
OSD 64
5.3. TIME & TIMER SETTING
When you enter “Time” “Local Time Setting” or “Sleep Timer” a
menu with three items will be opened (OSD 65). Use [
]
to select between the three options and confirm with [OK].
rev 1.0
5.3.1. TIMER
OSD 66
Select “Timer” item and press [OK] to enter the “Timer list”
menu (OSD 66).
The current time will be displayed in the first column. If the
current time is incorrect, please modify it with the [Number]
buttons at the “Time” menu.
1. Timer Number: You can press [
] to set the Timer
number. There are totally 8 timers.
PAG. 33
English
OSD 65
When you enter the “TV System” menu you will see the screen
like below (OSD 64):
1. Display Mode is used to switch the display mode. You can
select from Auto / PAL / PAL-M / NTSC 3.58/NTSC 4.43.
] to select the desired mode.
Press [
2. Aspect Mode is used to switch the screen aspect ratio mode.
You can select from Auto / 4:3 PS / 4:3 LB / 16:9. Press [
] to select the needed mode.
3. Video Output is use for switching the screen aspect ratio
mode. Now we provide below options: RGB / CVBS. You can
press [
] key to select each mode circularly.
4. VCR Loopthrought: If there is a VCR connected to the receiver and, the receiver is connected to the TV, user can choose
what prefer to watch on TV when both equipments are connected at the same time. If the selection is “VCR master”, the VCR
will be showed even the receiver is on. If the selection is “STB
master”, the receiver will be showed on the TV.
5. Standard Mod.: To choose the modulator output standard.
Using [
] you can chose between: PAL-BG / PAL-I /
PAL-DK / NTSC.
6. RF Channel: This option allows you to determine the initial
channel that the built-in modulator is supposed to occupy. This
is important in the case that you wish to connect the receiver to
an existing network.
] to
The output range is from channel 21 to 69. Press [
change the value.
7. In HDMI Mode, you can choose the number of lines and the
scan mode of the video signal you are sending by the HDMI
connector. Through the arrows [
], select among: 576P /
480P / 576 I / 480 I. (P: Progressive, I: Interleaved)
Note: If you have the HDMI output connected and you select
the progressive mode, the SCART output is automatically disabled.
8. Press [Exit] to close the “TV System” menu.
English
OSD 67
OSD 68
2. Timer Mode: Select how often the timer is running: Once,
Daily, Weekly, Monthly and Yearly. Or switch the timer off.
3. Timer Service: You can choose between “DVR Recorder” /
“Radio Recorder” (so you can program a recording of a TV or
a Radio channel), “Reproduce Channel” / “Reproduce Radio”
(that way, you will assign the alarm function to a concrete TV
or Radio channel) or “Message mode” (creating a text message
that will appear on the screen).
4. “DVR Recorder” / “Radio Recorder” option: If you select this
option, the following fields of the image will be shown in order
to be configured (OSD 67).
- Start channel: Press [OK] to open the channel list and select
the channel you want to record. By default, when you enter
this option, it shows the current tuned channel.
- Start date: Introduce using the numerical keys on the remote
control the date on which you want to make the recording.
By default, when you enter this option, it shows the current
date.
- On time: Introduce BY using the numerical keys on the remote
control; the time when you want to start recording. By default,
when you enter this option, it shows the current time.
- Length: Settle the length of time you want the receiver to
record a channel. Once it is finished, the receiver will be
settled in Stand-By.
Note: If the date/ start time is prior to the current date/hour,
a warning message will be shown and you have to change the
date/start time.
Note: If the hard disk is full and there is not enough space for a
recording, a warning message will be shown on the screen.
Note: If during the recording, the hard disk fills up, the recording
stops and will only store the data recorded until that moment
(without losing the previously stored data).
If the TV is in TV mode, a recording timer will be activated
and a message will be shown on the screen, asking for a
confirmation of the recording or for the timer elimination. After
some seconds, if it is not confirmed or deleted, the PVR will
start the programmed recording.
5. “Channel reproduction” / “Radio reproduction” option: if you
select this option, the following fields of the image will be shown
in order to be configured (OSD 68).
- Start channel: Press [OK] to open the channel list and select
the channel you want to watch.
- Start date: Introduce using the numerical keys on the remote
control the date on which you want to activate the alarm
service.
- On time: Introduce using the numerical keys on the remote
control the time on which you want to activate the alarm
service.
- Length: Settle the length of time you want the receiver to keep
PAG. 34
rev 1.0
SYSTEM SETUP
SYSTEM SETUP
OSD 69
5.3.2. LOCAL TIME SETTING
rev 1.0
OSD 70
OSD 71
When you select “Local Time Setting” and press [OK] then you
will see a window like the one beside (OSD 70):
1. GMT Usage: This item is used to set the time by using the
time signal from the satellite. Press [
] to change the
setting.
2. The “GMT Offset” item is only available when “GMT Usage”
is set to “On”. Press [
] to set the “GMT Offset” value.
With every time you press the button the time offset will be
increased / decreased by half an hour.
3. Summer: this option is only available when “USE GMT” is
enabled. Use [
] to switch on/off the summer timetable.
4. “Date” and “Time” items are only available when the “GMT
Usage” is set to “Off”. Press [
] to select one item and
use number buttons to input time and date directly.
NOTE: If the current channel provides the correct time
information, you will see the current time after you entered
“Time” menu. If the channel doesn’t provide time information,
you have to input the date and time information manually. The
most channels support the time signal.
5. Show time: Use [
] to switch on/off this option. When
the option is enabled, the time will be displayed at the TV in a
frame in the top right margin.(OSD 71)
6. Press [Exit] to exit the menu.
PAG. 35
English
one channel. Once it is finished, the receiver will be settled
in StandBy. If you do not want the receiver to be settled on
Stand-By, you have to configure the length to 00:00.
Note: If the date/ start time is prior to the current date/hour,
a warning message will be shown and you have to change the
date/start time.
6. Message option: If you select this option, the following image
fields will be active in order that you can configure them (OSD
69).
- Start message: Use the keys [
] to select the text you
want to appear on the screen
- Start date: Introduce using the numerical keys on the remote
control the date on which you want to activate the service.
- On time: Introduce using the numerical keys on the remote
control the time on which you want to activate the service.
Automatically, a message will be shown although the receiver
is ON or in Standby.
Note: If the date/ start time is prior to the current date/hour,
a warning message will be shown and you have to change the
date/start time.
7. Press [Exit] to leave the “Timer” menu.
Note: If the receiver is in stand-by, and Low Power Consumption
mode is active, the receiver will switch on 1 minute before the
programmed event.
SYSTEM SETUP
5.3.3. SLEEP TIMER
Press [OK] button in this option to set the sleep timer. You will
see “SLEEP TIME OFF / SLEEP TIME 10 / SLEEP TIME 30
/ SLEEP TIME 60 / SLEEP TIME 90 / SLEEP TIME 120”.
(OSD 72)
If you set a sleep time, the system will change to Standby mode
after the chosen time period.
English
OSD 72
5.4. OSD SETTING
When you select “OSD Setting” you will see a screen like
beside (OSD 73):
] to select “On” or “Off”. If the
1. Subtitle Display: Press [
current channel has subtitle information, it will be displayed if
this function is “On”. If this function is “Off” subtitles won’t be
displayed.
2. OSD Timeout: This setting determines the duration the info
window is displayed on the screen when you change channels.
Press [
] to set the time between 1 to 10 seconds.
3. Position: To define the position of the information’s bar
(top/bottom).
4. OSD Transparency: With this parameter you can set the
transparency of the menus. Press [
] select the value
between 10%, 20%, 30%, and 40% and “NO” (means no
transparency function).
5. Load OSD Setting Default: If you want to reset your OSD
settings to the default settings then select this item and press
[OK].
6. Press [Exit] button to leave the “OSD Setting” menu.
OSD 73
OSD 74
You can set a password for anyone who wishes to operate
the “Installation” menu. You can also set the password to
lock channels. Below you find how to set and change the
password.
1. On “Parental Lock”, press [OK] to open a dialogue box and
input the password. After you entered the correct password,
you will see a screen like beside (OSD 74):
2. Menu Lock: If Menu Lock is set to “Yes” then you need to
enter the password every time you want to open then menu. If
it is set to “No” then you can open the menu without entering
the password first.
3. Channel Lock: If set to “Yes” then you need to enter the
password before you can see those channels which have been
marked as locked channels in the Channel menu. If it is set to
“No” then even those channels can be selected without entering
the password first.
4. New Password: Here you can change the existing password.
You should do this after you set up the receiver the first time
PAG. 36
rev 1.0
5.5. PARENTAL LOCK
SYSTEM SETUP
OSD 75
and every time when you think that your password is known
by unauthorized persons. To change the password, enter the
new password in the “New Password” item and repeat the
same one in the “Confirm Password” item. If the passwords
are not identically then you will see a warning message. If you
entered the same new password in both fields then you will see
the message “Saving Data, Please Wait…”. From now on you
need to use the new password to open locked menus or locked
channels.
NOTE: The default password is 0000
5. Press [Exit] to leave the “Parental Lock” menu.
Here you can set the power output to the LNB (OSD 75). If
your receiver is connected to the LNB directly then you need to
set the LNB Power to “On”. If your receiver is connected to a
multi switch (SMATV signal distribution system) then it may be
that you don’t need to provide the power to the LNB. But since
this is depending on the kind of installed distribution system we
recommend you to contact your installer or to refer to the user
manual of this system to get the correct information.
You also just can change this setting and check if you still can
receive the channels. If the LNB Power is off and you still can
see all channels then we recommend this setting.
5.7. RCU POSITION SWITCH
rev 1.0
OSD 76
In order to avoid interferences between remote controls, you
have the possibility to change the code of it, to do that you have
to change the position of a switch in the remote control.
But first of all you have to change this code in the receiver. You
can do this in the menu “RCU Position” (OSD 76).
You have to select the same position in the receiver than in the
remote control (OSD 77).
OSD 77
PAG. 37
English
5.6. LNB POWER
TOOLS
6. TOOLS
English
OSD 78
Press [Menu] in the TV mode to enter the main menu (OSD
78).
] to select the Tools item.
1. Press [
2. Press [OK] to enter the selected item.
In the Tools menu (OSD 79):
3. Press [
] to select the wanted menu item.
4. Press [OK] to enter the selected item among.
- Information
- Quick Setup
- Game
- Factory Default
- Software Upgrade
- SatcoDX Auto Programing
- Smartcard
6.1. INFORMATION
OSD 79
1. When you select the “Information” menu you will see a
screen like beside (OSD 80). The screen displays data about
the current channel. This function is the same as the function
[Info] in the full screen TV mode.
2. Press [Exit] button to leave the information display.
6.2. QUICK SETUP
rev 1.0
OSD 80
The receiver includes an installation assistant that will help you
to setup the different parameters as you can see at OSD 81.
1. Language: press [
] to select the language that will
appear on the menus (see point 5.1.)
2. First Audio: Some channels offer more than one audio
language. This function allows you to set the preferred audio
language for those channels using[
]. (See point 5.1.)
3. Second Audio: Some channels offer more than one audio
language. This function allows you to set the second audio
language for those channels using[
]. (See point 5.1.)
4. LNB Power: If your receiver is connected to the LNB directly
then you need to set the LNB Power to “On”. If your receiver is
connected to a multi switch (SMATV signal distribution system)
then it may be that you don’t need to provide the power to the
LNB. (See point 5.6.)
5. Single Search: Selecting this option and pressing [OK], you
will access to the Antenna Setup menu (see point 4.1.).
6. Multi search: Selecting this option and pressing [OK], you
will access to “Multi search” menu (see point 4.3.).
OSD 81
PAG. 38
TOOLS
6.3. GAME
When you enter “Game” menu, you will see three Games
include Tetris, Snake and Othello (OSD 82).
6.3.1. TETRIS
OSD 82
6.3.2. SNAKE
1. Mark “Setup” and press [
] to select the level (speed).
2. Mark “Start” and press [OK] to start the game.
3. Mark “Cancel” and press [OK] to leave the game.
4. Play the game:
- Press [
] to guide the snake to the red blocks.
Every block you ate increases the length of the snake. If the
snake runs against a wall or against itself then it dies.
- Press [OK] to Pause/Play the game
- Press [Exit] to quit the game and return to the Game menu.
6.3.3. OTHELLO
1. Mark “Setup” and press [
] to select the game level
(degree of difficulty).
2. Mark “Start” and press [OK] to start the game.
3. Mark “Cancel” and press [OK] to leave the game.
4. Play the game:
- Press [
] to position the round mark.
- Press [OK] to set your stone.
- Press [Exit] to quit the game and return to the Game menu.
rev 1.0
6.4. FACTORY DEFAULT
OSD 83
When you press [OK] on the “Default Value” item:
1. A dialogue box will occur where you need to enter the
password.
2. After you input the correct password a warning message will
be displayed like the one beside (OSD 83).
3. If you select “Yes” then all changes you made will be reset to
default values. Make sure you really want to do this!
4. Press [Exit] in both steps will close the window without
resetting the receiver.
PAG. 39
English
1. Mark “Setup” and press [
] to select the level (speed).
2. Mark “Start” and press [OK] to start the game.
3. Mark “Cancel” and press [OK] to leave the game.
4. Play the game:
- Press [
] to move the block left or right
- Press [ ] to rotate the block clockwise
- Press [ ] to drop the block faster
- Press [OK] to Pause/Play the game
- Press [Exit] to leave the game and return to the Game
menu.
TOOLS
6.5. SOFTWARE UPGRADE
There are two ways of upgrading the software of the receiver as
you can see at OSD 84.
6.5.1. RS232 UPGRADE
English
OSD 84
OSD 85
OSD 86
1. This function allows you to upgrade the software of the
receiver. This can be done from PC to receiver or from a master
receiver to a slave receiver.
2. Connect master receiver or PC to the slave receiver via serial
interface (0-Modem cable). Enter the “Software Upgrade”
menu of the master receiver and press [
] to change the
upgrade mode. Upgrade modes include: allcode / maincode /
radioback / defaultdb / userdb (OSD 85).
3. Switch on the slave receiver.
4. Mark “Start” on the master reeciver and press [OK] to
start upgrade. Wait until the display on the front panel shows
“END”. Then switch off the receiver and on again. Now the new
software is used.
7. Press [Exit] to save the setting without upgrade.
For more information about software upgrade, please visit
http://www.universbyfte.com
6.5.2. UPGRADE BY SATELLITE
This function can upgrade the software of your receiver through
data sent by a satellite. At the moment we offer satellite updates
only through ASTRA1 satellite.
1. Select the satellite and TP or input the TP value and
download PID.
2. Then mark “Start” and press [Enter] to begin the download
of the upgrade (OSD 86). This may need up to 60 Minutes.
Therefore we suggest using of this function only if you don’t
intent to watch TV during this time.
At the moment of writing this manual, the data for the software
upgrade by Satellite is:
•Satellite: Astra
•TP Frequency: 12604 MHz.
•Symbol Rate: 22000
•Polarity: Horizontal
•Download PID: 1277
For changes in the data of the satellite please visit http://www.
universbyfte.com
OSD 87
This option allows updating the software of the receiver with the
received data from a USB 2.0 memory device. To do it, connect
a USB 2.0 memory device to the receiver and accede to this
menu option (OSD 87).
PAG. 40
rev 1.0
6.5.3. UPGRADING THOUGH USB
TOOLS
OSD 88
For further information about the upgrading of the receivers,
please visit http://www.universbyfte.com, in the chapter about
upgrading receivers.
OSD 89
OSD 90
6.6. SATCODX AUTO PROGRAMMING
This function is using the tables of the SatcoDX websites to
update your channel and satellite lists.
1. Start the SatcoDX application on your PC.
2. Select “SatcoDX Auto Programming” item from the “Tools”
menu and press [OK]. The screen will show the message “OK
to Proceed” (OSD 89).
3. Press [OK] again and you will see the message “Ready to
Download” (OSD 90).
4. In the PC application set the Baud Rate to 115200 and start
the download procedure.
! Caution: The new download channels will delete the original
channels list. Please be careful before using it.
6.7. SMARTCARD
In this option, you can fi nd information about the conditional
access system. If there is no card or it is placed incorrectly,
information about “No card” o “Unknown” will be showed on
the screen.
With a FELEC-CAS card, information about the card will be
showed (OSD 91).
rev 1.0
Note: Card must be inserted with chip at the bottom side.
OSD 91
PAG. 41
English
The last software version to be loaded must be placed at the
root path of your USB device.
1. Upgrade mode: Select with [
], the mode of
upgrading.
], the name of the file to be
2. Update file: Select with [
loaded.
3. Select “Start” and press [OK]. An alert message appears
indicating not to take out the memory device during the loading
process.
4. Once the file has been loaded, it requires the conformity
to end the upgrading process, writing into the receiver the
upgrading. Press [OK] to upgrade the receiver (OSD 88). In
case during the reading of the file, it is corrupted or it would be
a not appropriated for this model of receiver, an alert message
would appear “Error reading the USB disk”.
5. After pressing [OK] the receiver will write into the Flash
memory, and it will reboot to end the upgrading process.
DVR MANAGEMENT
7. MEDIA MANAGEMENT
English
OSD 96
Press the key [Menu] on the remote control to go to the main
menu (OSD 96).
] to settle the
1. Press the arrows on the remote control [
option of DVR management.
2. Press [Ok] to enter the submenu DVR Management
In the submenu DVR management (OSD 97):
3. Press the keys on the remote control [
] to move to the
different options on the menu.
4. Press [Ok] to go to the selected option on the submenu.
- Media List
- Media Control
- Disk Information
- Upgrade
7.1. MEDIA LIST
OSD 97
This menu option has the lists of recordings as well as the
music, pictures and video files that the HDD contains. You can
manage the contents and to access to the multimedia player.
In the first screen you will have to select the HDD partition
where multimedia files are.
Press the cursors button of the remote control to select the
desired item and then press OK to proceed. Now you will be
able to select different multimedia contents lists.
Press [
] to move along the different options.
- Mananage the recordings (Record List)
- Multimedia Player (MP3 List, Picture List, Video List, List of
all files).
Preview window of
the selected file
Recorded files
Information about
the selected file.
OSD 98
PAG. 42
Information about
the capacity of
the hard disk
rev 1.0
Options
DVR MANAGEMENT
7.1.1. RECORD MANAGEMENT - RECORD LIST
With this option of the menu, you can reproduce, rename, block
and delete recordings.
You can go to this option using the menu or directly pressing
the key [PVR] on the remote control.
Information on the window (OSD 98):
OSD 99
7.1.1.1. HOW TO REPRODUCE A RECORDING
7.1.1.2. HOW TO RENAME A RECORDING
Press the key [Red] to rename a recording.
- A window will appear where you can change the name of the
record (OSD 99). Press OK to go out and modify the name.
- Once the name is changed, it won’t be saved until you leave
the “Recording Management”.
- Press the [Exit] key to leave. A window will ask for confirmation
to save the changes.
7.1.1.3. HOW TO BLOCK A RECORDING
OSD 100
With this function it is possible to block a recording so it is
necessary to introduce a password to watch it.
- If you want to block a recording, select it and press the
[Green] key
- The blocked channel is marked with an icon (OSD 100).
- In order that the blockade of channels work, it is necessary
that the blocking option is activated in the menu of “Blockade
with password” (chapter 5.5).
- Press the key [Exit] to leave. A window will ask for confirmation
of saving the changes.
7.1.1.4. HOW TO DELETE A RECORDING
rev 1.0
To delete one or more recordings, press the [Yellow] key on
the recording you want to delete (if you want to delete several
recordings, select them one by one).
- A window appears and asks for the password to delete a
recording. If it has not been modified, it is by default the code
“0000”.
- A mark will appear on the name of the channel (OSD 101).
- The marked recordings will be deleted once you confirmed
that you want to save the changes by leaving the menu.
OSD 101
PAG. 43
English
If you want to reproduce a recording, you only have to select it
and press the key [OK]. In the meanwhile, you can watch the
recorded file on the preview window.
DVR MANAGEMENT
7.1.1.5. HOW TO DELETE ALL THE RECORDINGS
OSD 102
To delete all of the recordings, press the [Blue] key.
- A window appears and asks for the password to delete all
the recordings. If it has not been modified, it is by default the
code “0000”.
- A mark will appear on the names of the channels (OSD
102).
- The marked recordings will be deleted once you confirmed
that you want to save the changes by leaving the menu.
7.1.2. MULTIMEDIA PLAYER
English
In this menu option you can accede and manage the contents
of the HDD previously copied from your computer.
You also can create playlists of music, pictures or video.
Press [
] to shift along the different lists.
Press [Menu] button to Exit.
OSD 103
OSD 104
- CONTENT LISTS OF THE HARD DISK
These lists contain all the files of the HDD that you have copied
previously from your computer.
The content is shown organized in the same folders you have
created, and it can be shown in different manners in the
following lists:
- All the files (ALL)
- MP3 Files
- Pictures (JPG)
- Video (MPG)
- PLAYLISTS
These lists are created adding the files you want to the previous
lists. You can create 3 lists:
- Picture List
- Music List
- Video List
Press [OK] on any file from one list to play all the files
contained.
The functions are similar in all the lists.
Press the keys [
] to move along the files and press [OK]
to enter and exit of the folders or open a file or playlist. (OSD
103)
It allows you to manage the file or folder.
- Select the file or folder and press the [Red] button.
- New functions will appear: (OSD 104)
OSD 105
PAG. 44
rev 1.0
7.1.2.1. EDIT FILES AND FOLDERS
DVR MANAGEMENT
- RENAME
1. Press the [Red] button to rename the file.
2. A new window appears where you can change
the name of the recording moving through cursors.
Press OK to exit and modify the name.
3. Once the change is done, i will be not modified
until you do not exit from the list.
4. Press the [Menu] button to exit. A new window
will request information to save the changes.
OSD 106
1. Press the [Green] button to delete the file.
2. A new window appears where you can select
between deleting the selected file [Red] or all
the files with the same format [Green] (OSD 105).
3. The deletion mark will appear after the name of
the file.
4. The selected recording will be deleted once you
confirm to sabe the changes when you exit the
menu.
-MOVE
OSD 107
1. Press the [Yellow] button to move the file.
2. A mark appears behind the file you want to move
(OSD 106).
3. Go to the folder you want to move and press
again the [Yellow] button. A message will appear on
the screen requesting for confirmation.
-CREATE A NEW FOLDER
1. Get into the folder where you want to create a
new one, and press the [Blue] button.
2. A new window appears where you can name the
new folder moving through the arrows and pressing
[OK] (OSD 107).
OSD 108
7.1.2.2. ADDING A NEW FILE TO THE LIST
rev 1.0
1. Go over the file you want to add to your customized playlist
and press the [Green] button.
2. A new window appears where you can select between
adding the selected file to the list [Red] or all the files of the
same format [Green] (OSD 108).
3. A new mark will appear after the name of the file (OSD
109).
OSD 109
PAG. 45
English
-DELETE
DVR MANAGEMENT
7.1.2.3. SEARCH FOR FILE
1. Press the [Blue] button to open the “Search” window. Use
the buttons [
and
] to write the characters of the
file name.
Press [OK] to confirm the characters. (OSD 110)
2. After writing down the characters, select OK and press [OK]
on the remote control.
OSD 110
7.1.2.4. LOGO
English
*Only available for the picture list of the Hard Disk.
Press the [Yellow] button over the picture you want it to appear
as background when you are listening to the radio or the Audio
playlist.
To restore the Univers logo background, delete the picture of
the Hard Disk or disconnect it from the Receiver.
7.1.2.5. CONFIGURE THE SLIDE SHOW
OSD 111
*Only available for the picture playlist.
This function allows you to configure the “slide show”, therefore,
to play the picture playlist.
1. Press
the [Yellow] button. (Config)
DVR
MANAGEMENT
2. A new window will appear where you should configure some
parameters (OSD 111):
- Size of the pictures on the screen.
- Time of viewing each picture on the screen.
- Repeat: When the playlist finishes, it starts again.
- Effect: Transition effects between picture and
picture.
- All Mp: Switch On or Off the background music.
If it is configured as “On”, the music of the MP3
playlist will be played.
7.1.2.6. AUDIO .MP3 PLAYER
rev 1.0
1. Press [OK] over the.MP3 file or list of .MP3 files you want
to play.
2. A Player will be opened as it is shown in the picture (OSD
112).
- [Red]: Pause / Play
- [Green]: Fast Rewind
- [Yellow]: Fast Forward
- [Blue]: Play Mode, only in case of playing the list
with various files.
-[
]: Volume control.
OSD 112
PAG. 46
DVR MANAGEMENT
7.1.2.7. PICTURE .JPG VIEWER
1. Press [OK] over the file .JPG that you want to show.
2. The selected picture will be shown on the screen.
If the file is included into the Picture Playlist, they all will be
shown in “slide show” mode.
]. (OSD
You can rotate the picture with the buttons [
113)
OSD 113
7.1.2.8. VIDEO .MPG PLAYER
7.2.- HDD CONTROL
In this menu you can find the options “Reserved TMS Size”,
“Jump Step Value”, “Record Type”, “Test Disk Speed”, “Record
Path” and “Format HDD” (OSD 115).
OSD 114
7.2.1. TMS RESERVED SIZE
Reserved Size for the storage of the Time Shifting.
The available options can vary depending on the capacity of the
external Hard Disk.
7.2.2. JUMP STEP VALUE
With this option you can settle the jump marks forward and
reward.
On a current reproduction, press the keys [
] or [ ■ ] to
make a jump of a certain period of time on the reproduction.
This period is configurable and the jumps can be: 1, 3, 5, 10
and 15 minutes.
If they are configured every 10 minutes, each time that you
press this key, it will jump automatically 10 minutes forward/
reward on the reproduction.
■
OSD 115
7.2.3. RECORD TYPE
In this option, you can configure the video format of the
recordings. Options: MPEG, Original TS (Transport Stream).
7.2.4. TEST DISK SPEED
rev 1.0
If you select “On” in this option, the receiver will check out the
speed when every recording is started.
OSD 116
PAG. 47
English
1. Press the button [OK] over a .MPG video or a list of .MPG
videos.
2. The file will be played on the screen. In case that you play a
playlist, it will play all the files one by one. (OSD 114)
DVR MANAGEMENT
7.2.5. RECORD PATH
In this option you will have to select the HDD partition where will
be saved your recordings.
7.2.6. FORMAT DISK
English
OSD 116
This option will format the hard disk, erasing it completely.
When you select this option, a window appears and asks for a
password to format the hard disk. If it has not been modified, it
is by default the code “0000”.
Once this code is given, the hard disk will be formatted and you
will lose all the saved recordings.
Note: This process is irreversible. Once you have selected this
option and you have given the password, the data will be lost.
7.3.- HDD INFORMATION
In the HDD information submenu you can see the capacity
of the hard disk. You also see the free space available (OSD
116).
7.4. UPGRADING THOUGH USB
This option allows updating the software of the receiver with the
received data from a USB 2.0 memory device. To do it, connect
a USB 2.0 memory device to the receiver and accede to this
menu option (OSD 116).
The last software version to be loaded must be placed at the
root path of your USB device.
1. Upgrade mode: Select with [
], the mode of
upgrading.
2. Update file: Select with [
], the name of the file to be
loaded.
3. Select “Start” and press [OK]. An alert message appears
indicating not to take out the memory device during the loading
process.
4. Once the file has been loaded, it requires the conformity
to end the upgrading process, writing into the receiver the
upgrading. Press [OK] to upgrade the receiver (OSD 117). In
case during the reading of the file, it is corrupted or it would be
a not appropriated for this model of receiver, an alert message
would appear “Error reading the USB disk”.
5. After pressing [OK] the receiver will write into the Flash
memory, and it will reboot to end the upgrading process.
For further information about the upgrading of the receivers,
please visit http://www.universbyfte.com, in the chapter about
upgrading receivers.
PAG. 48
rev 1.0
OSD 117
TECHNICAL SPECIFICATION
8. TECHNICAL SPECIFICATION
VIDEO
Decoding
Bit rate
MPEG-2 & MEPG-1 compatible
Max 15Mbps
PAL/NTSC
4:3, 16:9, Auto
720x480 @ 30fps; 720x576 @25fps
Output connector
Scart / RCA / HDMI
AUDIO
Decoding
Mode
MPEG-2/MPEG-1 layer I & II
Mono, Dual, Stereo, Joint stereo
Bit rate
Output connector
Max 384Kbps
Scart / RCA / SPDIF /HDMI
DEMODULATOR
Demodulation
Symbol rate
QPSK
SCPC/MCPC
Outer code
Inner code
RS (204, 188, 8)
ALL DVB rates
Energy dispersion
DVB-S recommendation
INPUT SIGNAL
Frequency
Input level
Channel bandwidth
950MHz ~ 2150MHz
-65dBm ~ -25dBm
36MHz
Input socked
F-type connector
RF MODULATOR
Input
Output
IEC 169-24 Male x 1
IEC 169-24 Female x 1
Band
TV Standard
UHF
PAL BG/I/DK, NTSC M
Output Channel
21~69(PAL), 14~83(NTSC)
LNB CONTROL
Power supply
13/18V (500mA max) with
Polarized control
DiSEqC control
short circuit protection
13/18V polarization (vertical/horizontal)
DiSEqC1.0 DiSEqC1.1 and DiSEqC 1.2
rev 1.0
MISCELLANEOUS
Supply voltage
Power consumption
100~240VAC/50~60Hz
Typ. 21 watts / Max. 25 watts
Operation temperature
Storage temperature
Dimension (W x D x H)
+5° to +40°
-20° to +70°
Weight
SmartCard
1.1Kg
240x190x45 mm
FELEC-CAS
PAG. 49
English
Output
Aspect ratio
Active pixel
CONFORMITY DECLARATION
“WE , UNIVERS BY FTE, DECLARE
U4123E
IS IN CONFORMITY WITH FOLLOWING DIRECTIVES
LOW VOLTAGE DIRECTIVE 2006/95/EC
EMC DIRECTIVE 2004/108/EC”
rev 1.0
English
THAT THE PRODUCTS
PAG. 50