DIGITAL FULL COLOUR MULTIFUNCTIONAL SYSTEM
MX-2010U/MX-2310U
START GUIDE
Keep this manual close at hand for reference whenever needed.
Caution!
For complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations.
The equipment should be installed near an accessible socket outlet for easy disconnection.
Notice for users in the UK
MAINS PLUG WIRING INSTRUCTIONS
The mains lead of this equipment is already fitted with a mains plug which is either a non-rewireable (moulded) or a rewireable type. Should the fuse need to be replaced, a BSI or ASTA
approved fuse to BS1362 marked
or
and of the same rating as the one removed from the plug must be used.
Always refit the fuse cover after replacing the fuse on the moulded plug. Never use the plug without the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied either cut-off the moulded plug (if this type is fitted) or remove by undoing the screws if
a rewireable plug is fitted and fit an appropriate type observing the wiring code below.
DANGER: The fuse should be removed from the cut-off plug and the plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be
inserted elsewhere into a 13A socket outlet as a serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
GREEN-AND-YELLOW:
BLUE:
BROWN:
Earth
Neutral
Live
As the colours of the wires in this mains lead may not correspond with coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked with the letter E, or by the safety earth symbol
or greenand-yellow.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red.
, or coloured green
If you have any doubt, consult a qualified electrician.
WARNING: THIS APPARATUS MUST BE EARTHED.
EMC (this machine and peripheral devices)
„„ Warning:
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
This machine contains the software having modules developed by Independent JPEG
Group.
This product includes Adobe® Flash® technology of Adobe Systems Incorporated.
Copyright© 1995-2007 Adobe Macromedia Software LLC. All rights reserved.
Peripheral devices are described in the [PERIPHERAL DEVICE] in the Operation Guide.
2
For the users of the fax function
„„ FAX interface cable and Line cable:
These special accessories must be used with the device.
The declaration of conformity may be consulted at: http://www.sharp.de/doc/MX-FX11.pdf
SOFTWARE LICENCE
The SOFTWARE LICENCE will appear when you install the software from the CD-ROM. By using all or any portion of the software on the CD-ROM or in the machine, you are agreeing
to be bound by the terms of the SOFTWARE LICENCE.
•
•
•
•
•
The explanations in this manual assume that you have a working knowledge of your Windows or Macintosh computer.
For information on your operating system, please refer to your operating system manual or the online Help function.
The explanations of screens and procedures in this manual are primarily for Windows Vista® in Windows® environments. The screens may vary depending on the version of the operating system.
This manual contains references to the fax function. However, please note that the fax function is not available in some countries and regions.
This manual contains explanations of the PC-Fax driver and PPD driver. However, please note that the PC-Fax driver and PPD driver are not available and do not appear on the software for installation in some countries and regions.
In this case, please install the English version if you want to use these drivers.
• Considerable care has been taken in preparing this manual. If you have any comments or concerns about the manual, please contact your dealer or nearest authorised service representative.
• This product has undergone strict quality control and inspection procedures. In the unlikely event that a defect or other problem is discovered, please contact your dealer or nearest authorised service representative.
• Aside from instances provided for by law, SHARP is not responsible for failures occurring during the use of the product or its options, or failures due to incorrect operation of the product and its options, or other failures, or for
any damage that occurs due to use of the product.
Products that have earned the ENERGY STAR® are designed to
protect the environment through superior energy efficiency.
The products that meet the ENERGY STAR® guidelines carry the logo shown above.
The products without the logo may not meet the ENERGY STAR® guidelines.
„„ Warranty
While every effort has been made to make this document as accurate and helpful as
possible, SHARP Corporation makes no warranty of any kind with regard to its content.
All information included herein is subject to change without notice. SHARP is not
responsible for any loss or damages, direct or indirect, arising from or related to the use
of this operation manual.
© Copyright SHARP Corporation 2010. All rights reserved. Reproduction, adaptation
or translation without prior written permission is prohibited, except as allowed under
copyright laws.
MATERIAL SAFETY DATA SHEET
The MSDS (Material Safety Data Sheet) can be viewed at the following URL address: http://www.sharp-world.com/corporate/info/index.html
3
Contents
CAUTIONS ———————————————————————————— 5
SPECIFICATIONS ————————————————————————
15
Symbols in this manual ————————————————————————
5
Basic Specifications / Copier specifications ———————————————— 15
Power notes —————————————————————————————
5
Automatic document feeder (Standard equipment) ———————————— 16
Installation notes ———————————————————————————
6
Tray ————————————————————————————————— 16
About consumables ——————————————————————————
7
Finisher ——————————————————————————————— 16
Handling precautions —————————————————————————
7
Punch module ———————————————————————————— 17
SUPPLIES ——————————————————————————————
9
Fax Specifications ——————————————————————————— 17
Emission of noise and chemicals ———————————————————— 10
Network Printer Specifications ————————————————————— 18
Part Names ———————————————————————————
11
TURNING THE POWER ON AND OFF ———————————————
12
OPERATION MANUALS AND HOW TO USE THEM —————————
13
How to read the Operation Guide ———————————————————— 14
Network Scanner Specifications ————————————————————— 18
INFORMATION ON DISPOSAL ——————————————————
19
Information on Disposal for Users (private households) —————————— 19
Information on Disposal for Business Users ——————————————— 19
TO THE ADMINISTRATOR OF THE MACHINE ————————————
22
System settings password ——————————————————————— 22
Forwarding all transmitted and received data to the administrator
(document administration function) ——————————————————— 22
For the users of the fax function ————————————————————— 23
Trademark acknowledgments ——————————————————
27
4
CAUTIONS
Symbols in this manual
WARNING
To ensure safe use of the machine, this manual uses various safety symbols.
The safety symbols are classified as explained below. Be sure you understand
Indicates a risk of death or serious injury.
CAUTION
Indicates a risk of human injury or property damage.
the meaning of the symbols when reading the manual.
Meaning of the symbols
CAUTION!
HOT
PINCH POINT
KEEP CLEAR
PROHIBITED
ACTIONS
DO NOT
DISASSEMBLE
MANDATORY
ACTIONS
Power notes
WARNING
Be sure to connect the power cord only to a power outlet that meets the specified voltage
and current requirements. Also make certain the outlet is properly grounded. Do not use an
extension cord or adapter to connect other devices to the power outlet used by the machine.
Using an improper power supply may cause fire or electrical shock.
Do not damage or modify the power cord.
Placing heavy objects on the power cord, pulling it, or forcibly bending it will
damage the cord, resulting in fire or electrical shock.
* For the power supply requirements, see the name plate in the lower left corner of the left side of the
machine.
Do not insert or remove the power plug with wet hands.
This may cause electrical shock.
CAUTION
When removing the power plug from the outlet, do not pull on the cord.
Pulling on the cord may cause damage such as wire exposure and breakage, and may result in fire or
electrical shock.
When moving the machine, switch off the main power and remove the power plug from the outlet
before moving.
The cord may be damaged, creating a risk of fire or electrical shock.
If you will not use the machine for a long time, be sure to remove the power plug from the outlet
for safety.
5
Installation notes
CAUTION
Do not install the machine on an unstable or slanted surface. Install the machine on a surface
that can withstand the weight of the machine.
Risk of injury due to the machine falling or toppling.
If peripheral devices are to be installed, do not install on an uneven floor, slanted surface, or otherwise
unstable surface. Danger of slippage, falling, and toppling. Install the product on a flat, stable surface
that can withstand the weight of the product.
Risk of fire and electrical shock.
If dust enters the machine, dirty output and machine failure may result.
A small amount of ozone is created inside the machine during
printing. The amount of ozone created is not sufficient to be
harmful; however, an unpleasant odor may be noticed during large
copy runs, and thus the machine should be installed in a room with
a ventilation fan or windows that provide sufficient air circulation.
(The odor may occasionally cause headaches.)
* Install the machine so that people are not directly exposed to
exhaust from the machine. If installed near a window, ensure
that the machine is not exposed to direct sunlight.
Locations that are excessively hot, cold, humid, or dry
(near heaters, humidifiers, air conditioners, etc.)
The paper will become damp and condensation may form
inside the machine, causing misfeeds and dirty output.
SPECIFICATIONS (page 15)
If the location has an ultrasonic humidifier, use pure water for
humidifiers in the humidifier. If tap water is used, minerals and
other impurities will be emitted, causing impurities to collect
on the inside of the machine and create dirty output.
Near a wall
Be sure to allow the required space around the machine for
servicing and proper ventilation. (The machine should be no closer
than the distances indicated below from walls. The indicated
distances are for the case when a saddle finisher and large capacity
paper tray are not installed.)
When the machine is installed, the adjusters (5) must be lowered to the
floor to secure the machine (prevent it from moving).
Rotate the adjusters in the locking direction until they are in firm contact
with the floor.
(After moving the machine, lower the adjusters again to secure the
machine.)
Locations exposed to direct sunlight
Plastic parts may become deformed and dirty output may result.
Installing the machine next to a diazo copy machine may cause
dirty output.
Do not install the machine in a location with poor air
circulation.
Do not install in a location with moisture or dust.
If you find it necessary to reposition the machine due to
rearrangement of your office layout or other reason, retract the
adjusters from the floor, turn off the power, and then move the
machine.
Locations with ammonia gas
30 cm
30 cm
45 cm
Locations subject to vibration.
Lock
Release
Vibration may cause failure.
CAUTION
The machine includes a built-in hard drive. Do not subject the machine to shock or vibration. In
particular, never move the machine while the power is on.
• The machine should be installed near an accessible power outlet for easy connection.
• Connect the machine to a power outlet which is not used for other electric appliances. If a lighting
fixture is connected to the same outlet, the light may flicker.
6
About consumables
CAUTION
Do not throw a toner cartridge into a fire.
Store a toner cartridge out of the reach of children.
Toner may fly and cause burns.
Handling precautions
WARNING
Do not place a container of water or other liquid, or a metal object
that might fall inside, on the machine.
If you notice smoke, a strange odor, or other abnormality, do not use
the machine.
If the liquid spills or the object falls into the machine, fire or electrical shock
may result.
If used in this condition, fire or electrical shock may result.
Immediately switch off the main power and remove the power plug from
the power outlet.
Contact your dealer or nearest authorised service representative.
Do not remove the machine casing.
High-voltage parts inside the machine may cause electrical shock.
If a thunder storm begins, switch off the main power and remove the power plug from the outlet
to prevent electrical shock and fire due to lightning.
Do not make any modifications to this machine.
Doing so may result in personal injury or damage to the machine.
If a piece of metal or water enters the machine, switch off the main power and remove the power
plug from the power outlet.
Do not use a flammable spray to clean the machine.
Contact your dealer or nearest authorised service representative. Using the machine in this condition
may result in electrical shock or fire.
If gas from the spray comes in contact with hot electrical components or the fusing unit inside the
machine, fire or electrical shock may result.
7
CAUTION
Do not look directly at the light source.
Doing so may damage your eyes.
Do not block the ventilation ports on the machine. Do not install the machine in a location that
will block the ventilation ports.
Blocking the ventilation ports will cause heat to build up in the machine, creating a risk of fire.
The fusing unit and paper exit area are hot. When removing a misfeed,
do not touch the fusing unit and paper exit area. Take care not to burn
yourself.
When loading paper, removing a misfeed, performing
maintenance, closing the front and side covers, and inserting
and removing trays, take care that your fingers are not
pinched.
The machine includes the document filing function, which stores document image data on the machine’s hard drive. Stored documents can be called up and printed or transmitted as needed. If a hard drive failure occurs, it will no longer be
possible to call up the stored document data. To prevent the loss of important documents in the unlikely event of a hard drive failure, keep the originals of important documents or store the original data elsewhere.
With the exception of instances provided for by law, Sharp Corporation bears no responsibility for any damages or loss due to the loss of stored document data.
Laser information
Wave length
Pulse times
Output power
790 nm ± 10 nm
Normal paper mode (P/S = 104 mm/s) = (5.15 µs ± 0.03 ns) / 7 mm
Heavy paper mode (P/S = 70 mm/s) = (3.83 µs ± 0.03 ns) / 7 mm
Max 0.405 mW
„„ Caution
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
„„ “BATTERY DISPOSAL”
THIS PRODUCT CONTAINS A LITHIUM PRIMARY MEMORY BACK-UP
BATTERY THAT MUST BE DISPOSED OF PROPERLY.
PLEASE CONTACT YOUR LOCAL SHARP DEALER OR AUTHORISED
SERVICE REPRESENTATIVE FOR ASSISTANCE IN DISPOSING OF THIS
BATTERY.
Each instruction also covers the optional units used with these products.
This Digital Equipment is CLASS 1 LASER PRODUCT (IEC 60825-1 Edition
2-2007)
8
SUPPLIES
Standard supplies for this product that can replaced by the user include paper,
toner cartridges, and staple cartridges for the finisher.
For best copying results, be sure to use only Sharp Genuine
Be sure to use only SHARP-specified products for the toner cartridges, finisher
Supplies which are designed, engineered, and tested to
staple cartridge, and transparency film.
maximize the life and performance of Sharp products. Look
GENUINE SUPPLIES
for the Genuine Supplies label on the toner package.
Storage of supplies
„„ Proper storage
„„ Storing toner cartridges
1.Store the supplies in a location that is:
Store a new toner cartridge box horizontally with the top side up. Do not store
• clean and dry,
a toner cartridge standing on end. If stored standing on end, the toner may not
• at a stable temperature,
distribute well even after shaking the cartridge vigorously, and will remain inside
• not exposed to direct sunlight.
the cartridge without flowing out.
2.Store paper in the wrapper and lying flat.
3.Paper stored in packages standing up or out of the wrapper may curl or
become damp, resulting in paper misfeeds.
„„ Staple cartridge
The finisher require the following staple cartridge:
MX-SCX1 (for finisher)
Approx. 5000 per cartridge x 3 cartridges
Supply of spare parts and consumables
The supply of spare parts for repair of the machine is guaranteed for at least 7 years following the termination of production. Spare parts are those parts of the machine
which may break down within the scope of the ordinary use of the product, whereas those parts which normally exceed the life of the product are not to be considered
as spare parts. Consumables too, are available for 7 years following the termination of production.
9
Emission of noise and chemicals
Noise emission values
Noise emission values as measured according to ISO7779 are listed to the right.
Sound power level LWAd
Printing mode
(continuous printing)
7.5 B
Standby mode
(Low power level mode)
3.6 B
Sound pressure level LpA (actual measurement)
Printing mode
(continuous printing)
Bystander positions 50 dB(A)
Standby mode
Bystander positions 19 dB(A)
Emission density (measured according to RALUZ122: Edition Jun.2006)
Measured chemicals
Condition of copier
Ozone
Diffusion speed
3.0 mg/h or less
Black and white
1.5 mg/h or less
Colour
Dust
Styrene
Colour mode
Colour
Black and white
4.0 mg/h or less
When copier is in
Colour
1.8 mg/h or less
operation
Black and white
1.0 mg/h or less
Colour
Benzene
Black and white
Colour
TVOC
18 mg/h or less
Black and white
When on standby
0.05 mg/h under
-
10 mg/h or less
2.0 mg/h or less
10
Part Names
1
2
3
4
5
7
6
1Automatic document feeder (This is an option for MX-2010U)
2Front cover
3Output tray (Center tray)
4Operation panel
5Right tray
8
6[POWER] key (
)
7Bypass tray
8Main power switch
9
Tray 1
10Tray 2 (when paper feed tray is installed)*
9
10 11 12
11Tray 3 (when paper feed tray is installed)*
12Tray 4 (when paper feed tray is installed)*
* Peripheral device.
11
TURNING THE POWER ON AND OFF
This machine has two power switches. The main power switch is at the bottom left after the front cover is opened. The other power switch is the [POWER] key (
the operation panel.
) on
Turning on the power
(1) Switch the main power switch to the “
(2) Press the [POWER] key (
” position.
) to turn on the power.
Turning off the power
(1) Press the [POWER] key (
) to turn off the power.
(2) Switch the main power switch to the “
” position.
Main power
switch
Main power
indicator
[POWER] key
• When turning off the power, make sure that the indicator lights on the operation panel turn off as well.
• In the event of a power failure or other reason that causes the machine to suddenly turn off, turn back on the power of the machine and
then proceed to turn off the machine following the correct procedures.
Switching off the main power switch or removing the power cord from the outlet while any of the indicators are lit or blinking may damage
the hard drive and cause data to be lost.
• Switch off both the [POWER] key (
) and the main power switch and unplug the power cord if you suspect a machine failure, if there is
When the main power
switch is switched on, the
main power indicator on the
operation panel lights up.
a bad thunderstorm nearby, or when you are moving the machine.
When using the fax or Internet fax function, always keep the main power switch in the “on” position.
„„ Restarting the machine
In order for some settings to take effect, the machine must be restarted.
If a message in the touch panel prompts you to restart the machine, press the [POWER] key (
In some states of the machine, pressing the [POWER] key (
) to turn off the power and then press the key again to turn the power back on.
) to restart will not make the settings take effect. In this case, use the main power switch to switch the power off and then on.
12
OPERATION MANUALS AND HOW TO USE THEM
The instructions for this manual are separated in the following three sections.
Before using the machine
Printing and faxing from a
computer
Directions for use
MODEL: MX-2010U
MX-2310U
DIGITAL FULL COLOUR MULTIFUNCTIONAL SYSTEM
Software Setup Guide
OPERATION GUIDE
BEFORE INSTALLING
THE SOFTWARE
DIGITAL FULL COLOUR MULTIFUNCTIONAL SYSTEM
SETUP IN A WINDOWS
ENVIRONMENT
MX-2010U/MX-2310U
START GUIDE
Search based on
what you want to do
Search using the
table of contents
SETUP IN A MACINTOSH
ENVIRONMENT
BEFORE USING THE MACHINE
COPIER
TROUBLESHOOTING
PRINTER
MAKE A COPY
PRINT A DOCUMENT
SEND A FAX
FACSIMILE
SCANNER / INTERNET FAX
DOCUMENT FILING
SYSTEM SETTINGS
SCAN AN IMAGE /
SEND AN INTERNET FAX
Keep this manual close at hand for reference whenever needed.
SAVE A JOB AND
REUSE IT LATER
MAINTAIN
THE MACHINE
TROUBLESHOOTING
Keep this manual close at hand for reference
whenever needed.
About Operation Guide
Start Guide: this manual
Software Setup Guide (PDF)
Operation Guide (PDF)
This section explains precautions to ensure safe
This section explains how to install the various
Information on the copier, fax, and other various
usage, part names and how to switch on/off the power.
drivers needed when using this machine as a printer,
functions that this machine provides have been
This section also includes important information for
network scanner, or fax machine.
compiled into a PDF file called [Operation Guide].
persons that are responsible for the maintenance of this
Read this section when using this machine from
Read the Operation Guide to learn how to use this
machine.
a computer. The Software Setup Guide is on the
machine, when you want to know more about its
Read this section before using the machine for the first
“Software CD-ROM”.
functions, or when you have trouble operating it.
time.
MX-2010U: The [Operation Guide] is on the “manual CD-ROM”.
MX-2310U: The [Operation Guide] is downloaded from
this machine itself.
13
How to read the Operation Guide
The [Operation Guide] can be downloaded from the machine and viewed on a computer. You can download the [Operation Guide] following the procedures below while
the machine is connected to the network.
1 Confirm the machine’s IP address
First, press the [SYSTEM SETTINGS] key on the operation panel and then touch [List Print (User)] when it appears on the touch panel.
Next, select [NIC Page] from [Printer Test Page] and then touch the [Print] button. Confirm the machine’s IP address from the printed list.
2 Insert the machine’s IP address into the address bar of your web browser to access the machine.
http://machine’s IP address/
User verification may be required depending on the machine’s settings.
Please check with the machine’s administrator to obtain the account information necessary for verification.
3 Download the [Operation Guide]
Click [Operation Manual Download] from the page displayed. Next, select a language to download the file in from the [Language] list and then click on the [Download] button.
4 Double-click on the downloaded file to display the Operation Guide.
14
SPECIFICATIONS
Basic Specifications / Copier specifications
Name
MX-2010U/MX-2310U
Type
Desktop
Same size: 1:1 ± 0.8 % Enlarge: 115 %, 122 %, 141 %, 200 %, 400 %
Copy rations
Colour
Full colour
Copier system
Laser electrostatic copier
Scan (full colour): 600 × 600 dpi
Print: 600 × 600 dpi, equivalent to 9,600 dpi × 600 dpi
Gradation
Scan: equivalent to 256 levels / Print: equivalent to 256 levels
Original paper sizes
Max. A3 (11"×17") / sheets, bound documents
Paper feed / capacity
Max. paper feed / max. capacity
Continuous copy
Storage
paper, Envelopes
8-1/2" × 11"R, 7-1/4 × 10-1/2"R, 5-1/2" × 8-1/2"R
Lost margin (leading edge): 4 mm (11/64") ± 1 mm (± 3/64)
 1 GB = One billion bytes when referring to hard drive capacity. Actual
10 °C (54 °F) to 35 °C (91 °F) (20 % to 60 % RH)
10 °C (54 °F) to 30 °C (86 °F) (85 % RH)
Required power supply
plate in the lower corner of the left side of the machine.)
Power consumption Max. 1.84 kW (220-240 V) / 1.44 kW (100-127 V)
(including options such as the desk)
MX-2010U:
far edge: total 4 mm (11/64") ± 2 mm (± 6/64") or less
583 mm (W) × 623 mm (D) × 683 mm (H) *2
Dimensions
MX-2310U: 20 seconds or less
(22-61/64” (W) × 24-34/64” (D) × 26-57/64” (H))
MX-2310U:
 This may vary depending on the ambient conditions.
583 mm (W) × 623 mm (D) × 834 mm (H)
MX-2010U
(22-61/64” (W) × 24-34/64” (D) × 28-3/16 (H))
Weight
MX-2310U
MX-2010U: 63.4 kg (140 lbs.)
MX-2310U: 72 kg (159 lbs.)
851 mm (W) × 623 mm (D) (33-32/64" (W) × 24-34/64" (D))
 This may vary depending on the state of the machine.
(when shifter is not in operation)
Max. 999 copies
Local voltage ± 10 % (For the power supply requirements, see the name
Full colour: 10.0 seconds B/W: 7.4 seconds
Continuous copying speeds*
 Using 80 g/m2 (21 lbs.) weight paper
Leading edge / trailing edge: total 8 mm (21/64") or lessNear edge /
Full colour: 10.2 seconds B/W: 8.8 seconds
First-copy time
2,100 sheets in 4 trays (500 × 4) plus 100-sheet multi-bypass tray
Lost margin: (trailing edge): 2 mm (6/64") - 5 mm (- 13/64)
MX-2010U: 45 seconds or less
Warm-up time
Ambient environment
Multi-bypass tray: A3 wide (12" × 18") to A5R, 5-1/2" × 8-1/2"R,
Transparency film, Heavy paper, Envelopes
 Using 80 g/m2 (21 lbs.) weight paper
format capacity is less.
Tray 1-4: A3, B4, A4, A4R, B5, B5R, A5R, 11" × 17", 8-1/2" × 14",
8-1/2" × 13-1/2", 8-1/2" × 13-2/5", 8-1/2" × 13", 8-1/2" × 11",
500 sheets in one tray plus 100-sheet multi-bypass tray
HDD: 160 GB *1
A3 wide (12" × 18") to A5R, 5-1/2" × 8-1/2"R, Transparency film, Heavy
Copy sizes
Reduce: 25 %, 50 %, 70 %, 81 %, 86 %
Zoom range: 25 to 400 % (25 - 200 % using RSPF) in 1 % increments,
total 376 increments.
Scan (B/W): 600 × 600 dpi, 600 × 400 dpi, 600 × 300 dpi
Scanning resolution
MX-2010U
MX-2310U
Overall dimensions
(With multi-bypass tray extended)
964 mm (W) × 623 mm (D) (37-61/64" (W) × 24-34/64" (D))
(With right side exit tray extended)
A4, 8-1/2” × 11”
B5
20 copies/min. 23 copies/min.
A4R, 8-1/2” × 11”R
B5R
14 copies/min.
15 copies/min.
*1For the MX-2010U, when the hard disk expansion kit (MX-HD10) is installed.
B4, 8-1/2” × 14”
12 copies/min.
13 copies/min.
*2Height: to the glass surface
A3, 11” × 17”
10 copies/min.
11 copies/min.
* Continuous speed for same original source. Output may be temporarily
interrupted to stabilize image quality.
15
SPECIFICATIONS
Automatic document feeder
Name
MX-2010U: Reversing Single Pass Feeder (MX-RP12)
MX-2310U: Standard equipment
Document feeder types
Reversing Single Pass Feeder (RSPF)
Original paper sizes
A3 (11" × 17") to A5 (5-1/2" × 8-1/2")
Paper storage capacity
Scan speed (copy)
Plain paper 50 g/m2 (13 lbs.) to 128 g/m2 (32 lbs.)
Two-sided
(33/64"))
B/W: 50 one-sided sheets/minute
Paper weightThin paper 35 g/m2 (9 lbs.) to 49 g/m2 (13 lbs.)
Original paper types
100 sheets (80 g/m2 (21 lbs.)) (or maximum stack height of 13 mm
(A4 (8-1/2" × 11") horizontal) (600 × 400 dpi)
Colour: 36 one-sided sheets/minute
(A4 (8-1/2" × 11") horizontal) (600 × 600 dpi)
50 g/m2 (13 lbs.) to 105 g/m2 (28 lbs.)
Tray
Name
Tray 1
Tray 2
Tray 3
(MX-DE12)
(MX-DE13)
(MX-DE14)
Paper sizes
A3 (11" × 17") to A5R (5-1/2" × 8-1/2"R)
Useable paper
60 g/m2 (16 lbs.) to 209 g/m2 (56 lbs.)
Paper capacity
500 sheets
1,000 (500 × 2)
Dimensions
583 mm (W) × 577 mm (D) × 382 mm (H)
(22-61/64" (W) × 22-46/64" (D) × 15-1/64" (H))
MX-DE12: Approx. 21 kg (46 lbs.)
Weight
1,500 (500 × 3)
MX-DE13: Approx. 23 kg (51 lbs.)
MX-DE14: Approx. 28 kg (61 lbs.)
Finisher
Name
Finisher (MX-FN17)
Paper sizes
Paper sizes
Depends on feeder specifications
Useable paper
Paper weight
55 g/m2 (15 lbs.) to 256 g/m2 (68 lbs.)
No. of trays
Tray capacity (80g/m2 (21 lbs.))
Max. no. of stapled sheets
Max. no. of 50 sheets (A4 (8-1/2" × 11"), A4R (8-1/2" × 11"R), B5)
Max. no. of 30 sheets (A3 (11" × 17"), B4 (8-1/2" × 14"))
Staple position
3 locations (front, rear or both)
Tray 1
Required power supply
Supplied from this machine
Non-stapledA3 wide (12" × 18") / A3 (11" × 17") /
Weight
Approx. 12 kg (26 lbs.)
B4 (8-1/2" × 14"): 250 sheets
When output paper tray is stored
A4 (8-1/2" × 11") / A4R (8-1/2" × 11"R) /
428 mm (W) × 593 mm (D) × 198mm (H)
B5 / B5R (7-1/4” × 10-1/2”R) / A5R (5-1/2” ×
(16-55/64" (W) × 23-22/64" (D) × 7-51/64" (H))
8-1/2”R): 500 sheets
Staple functionA3 (11" × 17") / B4 (8-1/2" × 14"): 30 units or 250
sheets
Dimensions
When output paper tray is extended
612 mm (W) × 593 mm (D) × 198 mm (H)
(24-6/64" (W) × 23-22/64" (D) × 7-51/64" (H))
A4 (8-1/2" × 11") /A4R (8-1/2" × 11"R) /
B5: 30 units or 500 sheets
16
Punch module
Name
Paper size for punch module
Punch module (MX-PN11A, MX-PN11B, MX-PN11C, MX-PN11D) for
Required power supply
Supplied from finisher
finisher
Weight
Approx. 3 kg (7 lbs.)
A3 (11" × 17") to B5R (7-1/4" × 10-1/2"R)
 Cannot punch special types of paper such as OHP.
Dimensions
98 mm (W) × 477 mm (D) × 137 mm (H)
(3-55/64" (W) × 18-50/64" (D) × 5-26/64" (H))
MX-PN11A 2 holes
Holes
MX-PN11B 3 holes
MX-PN11C 4 holes
MX-PN11D 4 holes (wide)
Fax Specifications
Name
Facsimile expansion kit (MX-FX11)
Useable lines
General phone lines (PSTN), automated branch exchange (PBX)
Scanning line density
Normal characters:
8 dot/mm × 3.85 chars/mm
Small characters:
8 dot/mm × 7.7 line/mm
Fine characters:
8 dot/mm × 15.4 line/mm
High-definition:
16 dot/mm × 15.4 line/mm
Connection speed
Super G3: 33.6 kbps, G3: 14.4 kbps
Coding method
MH, MR, MMR, JBIG
Connection mode
Super G3 / G3
A3 (11" × 17") to A5 (5-1/2" × 8-1/2") (Paper with a max. length of
Original paper sizes for transmission
Registered paper size
Transmission time
Memory
A3 (11" × 17") to A5 (5-1/2" × 8-1/2")
Approx. 2 seconds * (A4 (8-1/2" × 11") Sharp standard paper, normal
characters, Super G3 (JBIG))
1GB
Touch dial memoryMax. 1,000 entries (Including group dialing for
Notes
fax, scanner, and Internet fax)
Group dialMax. of 500 entries
Mass transmissionsMax. of 500 recipients
*C
omplies with the 33.6 kbps transmission method for Super G3 facsimiles standardized by the International
1,000 mm* can be transmitted (one-sided and B/W only).)
Telecommunications Union (ITU-T). This is the speed for when sending an A4 (8-1/2" × 11") size piece of paper
* Internet fax (optional) is up to 800 mm (at 600 x 600 dpi).
of around 700 characters at standard image quality (8 × 3.85 chars/mm) in Hi-speed mode (33.6 kbps). This
is the transmission speed for image information only and does not include time for transmission control. The
actual time needed for a transmission depends on the content of the text, type of receiving fax machine, and
telephone line conditions.
17
SPECIFICATIONS
Network Printer Specifications
Type
Built-in type
Internal fonts (options)
80 fonts for PCL, 136 fonts for PS3 emulation
Continuous print speed
Same as continuous copy speed
Memory
Machine system memory and hard disk.
Data processing: 600 × 600 dpi,
Interface
10BASE-T/100BASE-TX/1000BASE-T, USB 2.0 (high speed mode)
Resolution
Page description language
Compatible protocols
Compatible OS
Print: 600 × 600 dpi, equivalent to 9600 x 600 dpi
Standard
SAPL-c *1
*1:SAPL is the abbreviation for Sharp Advanced Printing Language.
Options
PCL6 emulation *3
*2:When equipped with a PS extension kit (MX-PK11).
PS3 emulation *2, *3
*3:When equipped with a Printer Expansion kit (MX-PB14)
TCP/IP, IPv4/IPv6, IPX/SPX, NetBEUI, IPP, EtherTalk *2
For the MX-2010U, when equipped with the printer expansion kit (MX-PB14) and hard disk expansion kit
Windows 2000, Windows XP, Windows 2000 Server, Windows Server
(MX-HD10).
2003, Windows Vista, Windows Server 2008, Windows 7
Macintosh (Mac OS 9.0 ~ 9.2.2, OS X 10.2.8, 10.3.9, 10.4 ~ 10.4.11,
10.5 ~ 10.5.8, 10.6 ~ 10.6.2)*2
Network Scanner Specifications
Type
Scan resolution (main × vertical)
Colour scanner
(B/W)
100 × 100 dpi, 200 × 200 dpi, 300 × 300 dpi, 400 × 400 dpi
TIFF, PDF, encrypted PDF, XPS *3
600 × 600 dpi (push scan)
50 to 9,600 dpi *1 (pull scan)
Scan speed
(A4 (8-1/2" × 11") horizontal)
B/W
50 sheets/minute (one-sided)
Colour
50 sheets/minute (one-sided)
 When in standard mode using Sharp standard paper (A4 (8-1/2" ×
Compatible protocols
10BASE-T/100BASE-TX/1000BASE-T,
USB 2.0 (during USB memory scanning)
TCP/IP (IPv4)
(Gray scale/colour)
TIFF, JPEG, PDF, encrypted PDF, XPS *3
Compression method: JPEG (high, mid, and low compression)
TWAIN compliant
Driver
*1:You must decrease the scan size when increasing the resolution.
*2:There are cases when a connection cannot be established. Please contact your local dealer for more
information.
*3:XPS (XML Paper Specification)
Pull scan (TWAIN)Windows 2000, Windows XP, Windows 2000
Compatible OS *2
Compression method: decompression, G3 (MH), G4 (MMR)
11") size with 6% coverage) and the auto colour detector is turned off.
The speed varies depending on the data volume of the original.
Interface
Output format
When equipped with a Printer Expansion kit (MX-PB14)
Server, Windows Server 2003, Windows Vista,
For the MX-2010U, when equipped with the printer expansion kit (MX-PB14) and hard disk expansion kit
Windows Server 2008, Windows 7
(MX-HD10).
18
INFORMATION ON DISPOSAL
Information on Disposal for Users (private households)
„„ In the European Union
Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin! Used electrical and electronic equipment must be treated
separately and in accordance with legislation that requires proper treatment, recovery and recycling of used electrical and electronic equipment.
Following the implementation by member states, private households within the EU states may return their used electrical and electronic equipment
to designated collection facilities free of charge*. In some countries* your local retailer may also take back your old product free of charge if you
purchase a similar new one.
*) Please contact your local authority for further details. If your used electrical or electronic equipment has batteries or accumulators, please dispose of these separately beforehand
according to local requirements. By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment, recovery and recycling and thus prevent
potential negative effects on the environment and human health which could otherwise arise due to inappropriate waste handling.
„„ In other Countries outside the EU
Attention: Your product is marked
with this symbol. It means that used
electrical and electronic products
should not be mixed with general
household waste. There is a separate
collection system for these products.
If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal. For Switzerland: Used electrical
or electronic equipment can be returned free of charge to the dealer, even if you don’t purchase a new product. Further collection facilities are listed
on the homepage of www.swico.ch or www.sens.ch.
Information on Disposal for Business Users
„„ In the European Union
If the product is used for business purposes and you want to discard it: Please contact your SHARP dealer who will inform you about the take-back of the product. You might be
charged for the costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local collection facilities. For Spain: Please contact the
established collection system or your local authority for take-back of your used products.
„„ In other Countries outside the EU
If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal.
19
20
Administrator
Name:
Contact at:
Information that the administrator of the machine requires is printed on the back of this page.
(Separate this page from the manual and keep it in a safe place. In addition, fill in the name of
the administrator and the administrator’s contact information in the left hand margin.)
21
TO THE ADMINISTRATOR OF THE MACHINE
System settings password
A password is necessary to change the machine’s system settings using
administrator authority. System settings can be changed from either the
operation panel or using a computer web browser. After setting up the machine,
refer to [SYSTEM SETTINGS] in the Operation Guide to set a new password.
The administrator password is interfaced between the operation panel and the website, so
passwords changed on the operation panel will be effective when logging in on the website.
Password for logging in from this machine
The factory default password for the machine is “admin”.
Password for logging in from a computer
There are two accounts that can log in from a web browser: “Administrator” and
“User”. The factory default passwords for each account are shown on the right
side. Signing in as an “Administrator” will allow you to manage all the settings
available via web browser.
Account
Password
User
users
users
Administrator
admin
admin
Please take care not to forget newly set administrator passwords.
Forwarding all transmitted and received data to the administrator (document administration function)
This function is used to forward all data transmitted and received by the machine to a specified destination (Scan to E-mail address, Scan to FTP destination, Scan to
Network Folder destination, or Scan to Desktop destination).
This function can be used by the administrator of the machine to archive all transmitted and received data.
To configure the document administration settings, click [Application Settings] and then [Document Administration Function] in the Web page menu. (Administrator
rights are required.)
• The format, exposure, and resolution settings of transmitted and received data remain in effect when the data is forwarded.
• When forwarding is enabled for data sent in fax mode,
• The [Direct TX] key does not appear in the touch panel.
• Quick online transmission and dialling using the speaker cannot be used.
(Separate this page from the manual and keep it in a safe place.)
22
For the users of the fax function
Important safety instructions
• If any of your telephone equipment is not operating properly, you should immediately remove it from your telephone line, as it may cause harm to the telephone
network.
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the socket is specifically designed for wet locations.
• Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
• Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.
• Do not use a telephone to report a gas leak in the vicinity of the leak.
• Do not install or use the machine near water, or when you are wet. Take care not to spill any liquids on the machine.
• Save these instructions.
23
24
25
26
Trademark acknowledgments
The following trademarks and registered trademarks are used in conjunction with the
machine and its peripheral devices and accessories.
• Microsoft®, Windows®, Windows® 2000, Windows® XP, Windows Server® 2003,
Windows Vista®, Windows Server® 2008, Windows® 7 and Internet Explorer® are
registered trademarks or trademarks of Microsoft Corporation in the U.S.A. and other
countries.
• PostScript is a registered trademark of Adobe Systems Incorporated.
• Adobe and Flash are registered trademarks or trademarks of Adobe Systems
Incorporated in the United States and other countries.
• Adobe, the Adobe logo, Acrobat, the Adobe PDF logo, and Reader are registered
trademarks or trademarks of Adobe Systems Incorporated in the United States and
other countries.
• Macintosh, Mac OS, AppleTalk, EtherTalk and LaserWriter are trademarks of Apple
Inc., registered in the U.S. and other countries.
• Netscape Navigator is a trademark of Netscape Communications Corporation.
• Mozilla® and Firefox® are registered trademarks or trademarks of the Mozilla
Foundation in the U.S.A. and other countries.
• PCL is a registered trademark of the Hewlett-Packard Company.
• IBM, PC/AT, and PowerPC are trademarks of International Business Machines
Corporation.
• Sharpdesk is a trademark of Sharp Corporation.
• Sharp OSA is a trademark of Sharp Corporation.
• RealVNC is a trademark of RealVNC Limited.
• All other trademarks and copyrights are the property of their respective owners.
Candid and Taffy are trademarks of Monotype Imaging, Inc. registered in the United
States Patent and Trademark Office and may be registered in certain jurisdictions.
CG Omega, CG Times, Garamond Antiqua, Garamond Halbfett, Garamond Kursiv,
Garamond and Halbfett Kursiv are trademarks of Monotype Imaging, Inc. and may be
registered in certain jurisdictions. Albertus, Arial, Coronet, Gill Sans, Joanna and Times
New Roman are trademarks of The Monotype Corporation registered in the United
States Patent and Trademark Office and may be registered in certain jurisdictions. Avant
Garde, ITC Bookman, Lubalin Graph, Mona Lisa, Zapf Chancery and Zapf Dingbats
are trademarks of International Typeface Corporation registered in the United States
Patent and Trademark Office and may be registered in certain jurisdictions. Clarendon,
Eurostile, Helvetica, Optima, Palatino, Stempel Garamond, Times and Univers are
trademarks of Heidelberger Druckmaschinen AG, which may be registered in certain
jurisdictions, exclusively licensed through Linotype Library GmbH, a wholly owned
subsidiary of Heidelberger Druckmaschinen AG. Apple Chancery, Chicago, Geneva,
Monaco and New York are trademarks of Apple Inc. and may be registered in certain
jurisdictions. HGGothicB, HGMinchoL, HGPGothicB and HGPMinchoL are trademarks
of Ricoh Company, Ltd. and may be registered in some jurisdictions. Wingdings is a
registered trademark of Microsoft Corporation in the United States and other countries.
Marigold and Oxford are trademarks of Arthur Baker and may be registered in some
jurisdictions. Antique Olive is a trademark of Marcel Olive and may be registered in
certain jurisdictions. Hoefler Text is a trademark of Johnathan Hoefler and may be
registered in some jurisdictions. ITC is a trademark of International Typeface Corporation
registered in the United States Patent and Trademark Office and may be registered
in certain jurisdictions. Agfa is a trademark of the Agfa-Gevaert Group and may be
registered in certain jurisdictions. Intellifont, MicroType and UFST are trademarks of
Monotype Imaging, Inc. registered in the United States Patent and Trademark Office
and may be registered in certain jurisdictions. Macintosh and TrueType are trademarks
of Apple Inc. registered in the United States Patent and Trademark Office and other
countries. PostScript is a trademark of Adobe Systems Incorporated and may be
registered in some jurisdictions. HP, PCL, FontSmart and LaserJet are trademarks
of Hewlett-Packard Company and may be registered in some jurisdictions. The Type
1 processor resident in Monotype Imaging’s UFST product is under licence from
Electronics For Imaging, Inc. All other trademarks are the property of their respective
owners.
SHARP ELECTRONICS (Europe) GmbH
Sonninstraße 3, D-20097 Hamburg
27
MX-2010U/MX-2310U START GUIDE
PRINTED IN FRANCE
TINSE4860GHZ1
*TINSE4860GHZ1*