HC-03/05 Embedded Bluetooth Serial Communication Module AT command set Last revised: April, 2011 HC-05 embedded Bluetooth serial communication module (can be short for module) has two work modes: order-response work mode and automatic connection work mode. And there are three work roles (Master, Slave and Loopback) at the automatic connection work mode. When the module is at the automatic connection work mode, it will follow the default way set lastly to transmit the data automatically. When the module is at the order-response work mode, user can send the AT command to the module to set the control parameters and sent control order. The work mode of module can be switched by controlling the module PIN (PIO11) input level. Serial module PINs: 1. PIO8 connects with LED. When the module is power on, LED will flicker. And the flicker style will indicate which work mode is in using since different mode has different flicker time interval. 2. PIO9 connects with LED. It indicates whether the connection is built or not. When the Bluetooth serial is paired, the LED will be turned on. It means the connection is built successfully. 3. PIO11 is the work mode switch. When this PIN port is input high level, the work mode will become order-response work mode. While this PIN port is input low level or suspended in air, the work mode will become automatic connection work mode. 4. The module can be reset if it is re-powered since there is a reset circuit at the module. ===========================Notification ========================== 1. How to get to the AT mode. Way 1: Step 1: Input low level to PIN34. Step 2: Supply power to the module. Step 3: Input high level to the PIN34. Then the module will enter to AT mode. The baud rate is as same as the communication time, such as 9600 etc. Way 2: Step 1: Connect PIN34 to the power supply PIN. Step 2: Supply power to module (the PIN34 is also supplied with high level since the PIN34 is connected with power supply PIN). Then the module will enter to AT module. But at this time, the baud rate is 38400. In this way, user should change the baud rate at the AT mode, if they forget the communication baud rate. How to get to the communication mode: Step 1: Input low level to PIN34. Step 2: Supply power to the module. Then the module will enter to communication mode. It can be used for pairing. 2. How to set this module be the master role. Step 1: Input high level to PIO11. Step 2: Supply power to the module. And the module will enter to the order-response work mode. Step 3: Set the parameters of the super terminal or the other serial tools (baud rate: 38400, data bit:8, stop bit:1, no parity bit, no Flow Control) Step 4: Sent the characters “AT+ROLE=1\r\n” through serial, then receive the characters “OK\r\n”. Here, “\r\n” is the CRLF. Step 5: Input low level to PIO, and supply power to the module again. Then this module will become master role and search the other module (slave role) automatically to build the connection. 3. Notes. (1) HC-03 and HC-05’s command should end up with “\r\n”. It means when you finish programming, you should add terminator (“ENTER” or “0x0d 0x0a”) to the program. It’s different from HC-04 and HC-06 (They don’t need terminator). (2) The most common commands for HC-03 and HC-05 are: AT+ROLE (set master –slave), AT+CMODE( set address pairing) , AT+PSWD (set password). If you want the master module has the function of remembering slave module, the most simply way is: First, set AT+CMODE=1. Make the master module pair with the slave module. Second, set AT+CMODE=0. Then the master module just can make pair with that specified slave module. (3) When PIN34 keeps high level, all commands can be used. Otherwise, only some of them can be used. ============================================================== Detailed description of Command (AT command is case- sensitive, should end up with terminator (“enter” or “\r\n”).) 1. Test Command Response Parameter AT OK None Command Response Parameter AT+RESET OK None Response Parameter 2. Reset 3. Get the soft version Command +VERSION: <Param> AT+VERSION? Param: Version number OK Example : at+version?\r\n +VERSION:2.0-20100601 OK 4. Restore default status Command Response Parameter AT+ORGL OK None The parameter of default status: ①．Device type: 0 ②．Inquire code: 0x009e8b33 ③．Module work mode: Slave Mode ④．Connection mode: Connect to the Bluetooth device specified ⑤．Serial parameter: Baud rate: 38400 bits/s; Stop bit: 1 bit; Parity bit: None. ⑥．Passkey: “1234” ⑦．Device name: “H-C-2010-06-01” ……….. 5. Get module Bluetooth address Command Response Parameter +ADDR: <Param> AT+ADDR? Param: Bluetooth address OK Bluetooth address will show as this way: NAP: UAP: LAP(Hexadecimal) Example: Module Bluetooth address: 12: 34: 56: ab: cd: ef at+addr?\r\n +ADDR:1234:56:abcdef OK 6. Set/ inquire device’s name Command Response AT+NAME=<Param> OK Parameter 1. +NAME:<Param> AT+NAME? OK----success Param: Bluetooth device name Default: “HC-05” 2. FAIL----failure Example: AT+NAME=HC-05\r\n ---set the module device name: “HC-05” OK AT+NAME= “HC-05”\r\n ---set the module device name: “HC-05” OK at+name=Beijin\r\n ---set the module device name: “Beijin” OK at+name= “Beijin”\r\n ---set module device name : “Beijin” OK at+name?\r\n +NAME: Bei jin OK 7. Get the remote Bluetooth device’s name Command Response Parameter Param1: Remote Bluetooth 1. +NAME:<Param2> device address AT+RNAME?<Param1> OK----success Param2: Remote Bluetooth 2. FAIL----failure device address Bluetooth address will show as this way: NAP:UAP:LAP (Hexadecimal) Example: Bluetooth device address: 00:02:72: od: 22 : 24; device name: Bluetooth at+rname? 0002,72,od2224\r\n +RNAME:Bluetooth OK 8. Set/ inquire module role Command Response Parameter AT+ROLE=<Param> OK Param: 0---- Slave role + ROLE:<Param> 1---- Master role OK 2---- Slave-Loop role AT+ ROLE? Default: 0 Role introduction: Slave (slave role)----Passive connection; Slave-Loop----Passive connection, receive the remote Bluetooth master device data and send it back to the master device; Master (master role)----Inquire the near SPP Bluetooth slave device, build connection with it positively, and build up the transparent data transmission between master and slave device. 9. Set/inquire device type Command Response AT+CLASS=<Param> OK Parameter Param: device type Bluetooth device type is a 32-bit parameter indicates the device type and what type can be 1. + CLASS:<Param> supported. AT+ CLASS? OK----success Default: 0 2. FAIL----failure More information is provided at the appendix 1(device type introduction). For inquiring the custom Bluetooth device from around Bluetooth devices quickly and effectively, user can set the module to be non-standard Bluetooth device type, such as 0x1f1f (Hexadecimal). 10. Set/ inquire-Inquire access code Command Response Parameter 1. OK----success Param: Inquire access code 2. FAIL----failure Default: 9e8b33 AT+IAC=<Param> +IAC: <Param> The more information is provided at the OK appendix 2(Inquire access code introduction). AT+ IAC? Access code is set to be GIAC type (General Inquire Access Code:0x9e8b33), and used for seeking ( or being sought by ) all the Bluetooth devices around. For inquiring (or being inquiring by) the custom Bluetooth device from around Bluetooth devices quickly and effectively, user can set the inquire access code to be the other type number (not GIAC nor LIAC), such as 9e8b3f. Example: AT+IAC=9e8b3f\r\n OK AT+IAC?\r\n +IAC: 9e8b3f OK 11. Set/ inquire - Inquire access mode Command Response Parameter AT+INQM=<Param>, 1. OK----success Param: Inquire access mode <Param2>,<Param3> 2. FAIL----failure 0----inquiry_mode_standard 1----inquiry_mode_rssi Param2: the maximum of Bluetooth devices response +INQM:<Param>,<Param2>,<P Param3:The maximum of limited AT+ INQM? aram3> inquiring time OK The range of limited time: 1~48 ( Corresponding time:1.28s~61.44s) Default: 1, 1, 48 Example: AT+INQM=1,9,48\r\n ----Set Inquire access mode: 1) has RSSI signal intensity indicator, 2) stop inquiring once more than 9 devices response, 3) limited time is 48*l. 28=61.44s. OK AT+INQM\r\n +INQM:1, 9, 48 OK 12. Set/Inquire- passkey Command Response AT+PSWD=<Param> OK Parameter Param: passkey + PSWD : <Param> Default: “1234” AT+ PSWD? OK 13.Set/ Inquire- serial parameter Command Response AT+UART=<Param>,< Parameter Param1: baud rate( bits/s) OK Param2>,<Param3> The value (Decimal) should be one of the following: 4800 9600 19200 38400 57600 + 115200 UART=<Param>,<Para 23400 AT+ UART? m2>,<Param3> 460800 OK 921600 1382400 Param2:stop bit: 0----1 bit 1----2 bits Param3: parity bit 0----None 1----Odd parity 2----Even parity Default: 9600, 0, 0 Example: Set baud rate to be 115200, stop bit to be 2 bits, parity bit to be even parity. AT+UART=115200,1,2,\r\n OK AT+UART? +UART:115200,1,2 OK 14. Set/ Inquire - connection mode Command Response AT+CMODE=<Param> OK Parameter Param: 0----connect the module to the specified Bluetooth address. (Bluetooth specified address by the can be binding command) + CMODE:<Param> 1----connect the module to any AT+ CMODE? OK address (The specifying address has no effect for this mode.) 2----Slave-Loop Default connection mode: 0 15. Set/Inquire - bind Bluetooth address Bluetooth address will show as this way: NAP: UAP:LAP(Hexadecimal) Command Response AT+BIND=<Param> OK Parameter Param----Bluetooth address needed to be bind + BIND:<Param> Default address: AT+ BIND? OK 00:00:00:00:00:00 Bluetooth address will show as this way: NAP:UAP:LAP(Hexadecimal) This command is effective only when the module wants to connect to the specified Bluetooth address. Example: The module is at connection mode which connects to specified Bluetooth address, and the specified address is 12:34:56:ab:cd:ef. Command and the response show as follow: AT+BIND=1234, 56, abcdef\r\n OK AT+BIND?\r\n +BIND:1234:56:abcdef OK 16. Set/Inquire - drive indication of LED and connection status Command Response AT+POLAR=<Param1>, Parameter Param1:The value is OK <Param1> 0----PI08 outputs low level and turn on LED 1----PI08 outputs high level and turn on + POLAR=<Param1>, LED AT+ BIND? <Param1> OK Param2:The value is 0----PI09 output low level, indicate successful connection 1----PI09 output high level, and indicate successful connection Default: 1, 1 HC-05 Bluetooth module definition: The output of PI08 drives indication of LED work mode; the output of PI09 indicates the connection status. Example: PI08 outputs low level and turn on LED, PI09 outputs high level and indicates successful connection. Command and response show as follow: AT+POLAR=0, 1\r\n OK AT+POLAR?\r\n +POLAR=0, 1 OK 17. Set PIO single port output Command Response Parameter Param1: PIO port number(Decimal) Param2: PIO port status AT+PIO=<Param1>,<Param2> OK 0----low level 1----high level HC-05 Bluetooth module provides the user with the ports (PI00~PI07 and PI010) which can extern another input and output ports. Example: 1. PI010 port outputs high level AT+PI0=10, 1\r\n OK 2. PI010 port outpust low level AT+PI0=10, 0\r\n OK 18. Set PIO multiple port output Command Response AT+MPIO=<Param> OK Parameter Param: Mask combination of PIO ports number (Decimal) HC-05 Bluetooth module provides the ports (PI00~PI07 and PI010) which can extern another input and output ports to the user. (1) Mask of PIO port number = (1<<port number) (2) Mask combination of PIO ports number= (PIO port number mask 1|PIO port number mask 2|……) Example : PI02 port number mask=(1<<2) =0x004 PI010 port number mask =(1<<10)=0x400 Mask combination of PI02 and PI010 port number=(0x004|0x400)=0x404 Example: 1. PI010 and PI02 ports output high level AT+MPI0=404\r\n OK 2. PI04 port output high level AT+PI0=004\r\n OK 3. PI010 port output high level AT+PI0=400\r\n OK 4. All ports output low level AT+MPI0=0\r\n OK 19. Inquire PIO port input Command Response Parameter Param----PIO port value (16bits) Param=PI00 Param=PI01 +MPIO: <Param> AT+MPIO? Param=PI02 OK …… Param=PI010 Param=PI011 HC-05 Bluetooth module provides the user with the ports (PI00~PI07 and PI010) which can extern another input and output ports. 20. Set/ Inquire page scan and inquire scan parameter Command Response Parameter OK Param1:time interval +IPSCAN: inquiring AT+IPSCAN=<Param1>, <Param1>,<Param2>, Param2: duration in inquiring <Param2>, <Param3>,<Param4> Param3: time interval of paging <Param3>,<Param4>AT+I OK Param4: duration in paging PSCAN? The above parameters decimal. Default:1024,512,1024,512 Example: at+ipscan=1234,500,1200,250\r\n OK at+ipscan? +IPSCAN:1234,500,1200,250 of are 21. Set/ Inquire—SHIFF energy parameter Command Response Parameter AT+SNIFF=<Param1> Param1: maximum time ,<Param2>, OK Param2: minimum time <Param3>,<Param4> Param3: test time Param4: limited time +SNIFF: AT+IPSCAN? <Param1>,<Param2>,<Par am3>,<Param4> The above parameters are decimal. Default : 0,0,0,0 22. Set/ Inquire safe and encryption mode Command Response Parameter AT+SENM=<Param 1. OK----success Param: the value of safe mode: >,<Param2>, 2. FAIL----failure 0----sec_mode0+off 1----sec_mode1+non_secure 2----sec_mode2_service 3----sec_mode3_link AT+ SENM? +SENM:<Param>,<Param 4----sec_mode_unknown 2>, Param2: the value of encryption mode: OK 0----hci_enc_mode_off 1----hci_enc_mode_pt_to_pt 2----hci_enc_mode_pt_to_pt_and_bcast Default: 0,0 23. Delete authenticated device in the Bluetooth pair list Command Response Parameter AT+PMSAD=<Param> OK Param: Bluetooth device address Example: Delete the device ( address: 12:34:56:ab:cd:ef ) in the blue pair list at+rmsad=1234,56,abcdef\r\n OK ---- successful deletion Or at+rmsad=1234,56,abcdef\r\n FAIL ----There is no the Bluetooth device whose address is 12:34:56:ab:cd:ef in the pair list. 24. Delete all authenticated devices in the pair list Command Response Parameter AT+RMAAD OK None Example: Move all devices away from the pair list. at+rmaad\r\n OK 25. Seek the authenticated device in the Bluetooth pair list Command Response 1. OK----success Parameter Param: Bluetooth device address AT+FSAD=<Param> 2. FAIL----failure Example: Seek the authenticated device (address: 12:34:56:ab:cd:ef) in the pair list at+fsad=1234,56,abcdef\r\n OK ----the Bluetooth device whose address is 12:34:56:ab:cd:ef is found. at+fsad=1234,56,abcde0\r\n FAIL ----There is no the Bluetooth device whose address is 12:34:56:ab:cd:e0 in the pair list. 26. Get the authenticated device count from the pair list Command Response Parameter +ADCN:<Param> Param: OK Count Authenticated Device AT+ADCN? Example: at+adcn? +ADCN:0 ----There is no authenticated device in the pair list. OK 27. Get the Bluetooth address of Most Recently Used Authenticated Device Command Response AT+MRAD? Parameter + MRAD : <Param> Param: the Bluetooth address of OK Most Recently Used Authenticated Device Example: at+mrad? +MRAD:0:0:0 ----There is no device that has been used recently. OK 28. Get the work status of Bluetooth module Command Response Parameter Param: work status of module Return value： “INITIALIZED” “READY” ----initialized status ---- ready status + STATE: <Param> “PAIRABLE” ----pairable status OK “PAIRED” ----paired status “INQUIRING” ----inquiring status AT+STATE? “CONNECTING”----connecting status “CONNECTED”----connected status “DISCONNECTED”----disconnected status “NUKNOW”----unknown status Example: at+state? +STATE:INITIALIZED ----initialized status OK 29. Initialize the SPP profile lib Command Response Parameter 1. OK----success AT+INIT None 2. FAIL----failure 30. Inquire Bluetooth device Command Response Parameter Param1: Bluetooth address +INQ: <Param1>,<Param2>,<Param3>, Param2: device type AT+INQ …… Param3: RSSI signal OK intensity Example 1: at+init\r\n ---- Initialize the SPP profile lib( can’t repeat initialization) OK at+iac=9e8b33\r\n ----Inquire Bluetooth device has an access code OK at+class=0\r\n ----Inquire the Bluetooth device type at+inqm=1,9,48\r\n ----Inquire mode: 1) has the RSSI signal intensity indication, 2) stop inquiring if more than 9 Bluetooth devices response, 3) limited time in inquiring is 48*1.28=61.44s. At+inq\r\n ----inquire the Bluetooth device around +INQ:2:72:D2224,3E0104,FFBC +INQ:1234:56:0,1F1F,FFC1 +INQ:1234:56:0,1F1F,FFC0 +INQ:1234:56:0,1F1F,FFC1 +INQ:2:72:D2224,3F0104,FFAD +INQ:1234:56:0,1F1F,FFBE +INQ:1234:56:0,1F1F,FFC2 +INQ:1234:56:0,1F1F,FFBE +INQ:2:72:D2224,3F0104,FFBC OK Example 2: at+iac=9e8b33\r\n ----inquire the Bluetooth device has an access code OK at+class=1f1f\r\n ----inquire the Bluetooth device whose device type is 0x1f1f OK at+inqm=1,9,48\r\n ----inquire mode: 1) has the RSSI signal intensity indication, 2) stop inquiring if more than 9 Bluetooth devices response, 3) limited time in inquiring is 48*1.28=61.44s At+inq\r\n ----filter and inquire the Bluetooth device around +INQ:1234:56:0,1F1F,FFC2 +INQ:1234:56:0,1F1F,FFC1 +INQ:1234:56:0,1F1F,FFC1 +INQ:1234:56:0,1F1F,FFC1 +INQ:1234:56:0,1F1F,FFC2 +INQ:1234:56:0,1F1F,FFC1 +INQ:1234:56:0,1F1F,FFC1 +INQ:1234:56:0,1F1F,FFC0 +INQ:1234:56:0,1F1F,FFC2 OK Example 3: at+iac=9e8b3f\r\n ---- inquire the Bluetooth device whose access code is 0x9e8b3f OK at+class=1f1f\r\n ----inquire the Bluetooth device whose device type is 0x1f1f OK at+inqm=1,1,20\r\n ----inquire mode: 1) Has the RSSI signal intensity indication, 2) stop inquiring if more than 1 Bluetooth device response, 3) limited time in inquiring is 20*1.28=25.6s At+inq\r\n ----filter and inquire the Bluetooth device around +INQ:1234:56:ABCDEF,1F1F,FFC2 OK 31. Cancel Bluetooth device Command Response Parameter AT+INQC OK None 32. Set pair Command Response Parameter Param1: Bluetooth address of 1. OK----success remote device 2. FAIL----failure Param2: AT+PAIR=<Param1>,<Param2> limited time of connection (second) Example: Make pair with the remote Bluetooth device( address:12:34:56:ab:cd:ef), the limited time is 20s. At+pai=1234,56,abcdef,20\r\n OK 33. Connect device Command Response Parameter 1. OK----success Param: Bluetooth address of 2. FAIL----failure remote device AT+LINK=<Param> Example: Connect with the remote Bluetooth device (address: 12:34:56:ab:cd:ef) at+fsad=1234,56,abcdef\r\n ----To check whether the Bluetooth device (address: 12:34:56:ab:cd:ef) is in the pair list or not. OK at+link=1234,56,abcdef\r\n ----The Bluetooth device (address: 12:34:56:ab:cd:ef) is in the pair list. The connection can be built directly without inquiring. OK 34. Disconnection Command Response Parameter 1.+DISC:SUCCESS----successful Disconnection OK 2.+DISC:LINK_LOSS----lose the connection OK 3.+DISC:NO_SLC----No SLC connection AT+DISC None OK 4、+DISC:TIMEOUT----disconnection timeout OK 5、+DISC:ERROR----disconnection error OK 35. Enter to energy mode： Command Response Parameter AT+ENSNIFF=<Param> OK Param: Bluetooth address of device 36. Exit energy mode Command AT+EXSNIFF=<Param> Response OK Parameter Param: Bluetooth address of device Appendix 1：Introduction of AT command error code The form of error ---- ERROR:(error_code) error_code(Hexadecimal) Note 0 AT command error 1 Default result 2 PSKEY write error 3 Too long length of device name (more than 32 bytes). 4 No device name 5 Bluetooth address: NAP is too long. 6 Bluetooth address: UAP is too long. 7 Bluetooth address: LAP is too long. 8 No PIO number’s mask 9 No PIO number A No Bluetooth devices. B Too length of devices C No inquire access code D Too long length of inquire access code E Invalid inquire access code F The length of passkey is 0. 10 Too long length of passkey (more than 16 bytes) 11 Invalid module role 12 Invalid baud rate 13 Invalid stop bit 14 Invalid parity bit 15 Authentication device is not at the pair list. 16 SPP lib hasn’t been initialized. 17 SPP lib has been repeated initialization. 18 Invalid inquire mode 19 Too long inquire time 1A No Bluetooth address 1B Invalid safe mode 1C Invalid encryption mode Appendix 2: The introduction of devices The Class of Device/Service(CoD) is a 32 bits number that of 3 field specifies the service supported by the device. Another field specifies the minor device class, which describes the device type in more detail The Class of Device /Service (CoD) field has a variable format. The format is indicated using the ’within the CoD .The length of the Format Type field is variable and ends with two bits different from’11’.The version field starts at the least significant bit of the CoD and may extend upwards. In the ’format#1’ of the CoD (format Type field =00), 11 bits are assigned as a bit –mask (multiple bits can be set) each bit corresponding to a high level generic category of service class. Currently 7 categories are defined. These are primarily of a’ public service’ nature. The remaining 11 bits are used for indicating device type category and other device-specific characteristics. Any reserved but otherwise unassigned bits, such as in the Major Service Class field, should be to 0. Figure 1.2: The Class of Device/Service field (format type). Please note the krder in which the octets are sent on the air and stored in memory. Bit number 0 is sent first on the air . 1. MAJOR SERVICE CLASSES Bit no Major Service Class 13 Limited Discoverable Mode [Ref #1] 14 (reserved) 15 (reserved) 16 Positioning(Location identification) 17 Networking (LAN, Ad hoc, … ) 18 Rendering (Printing ,Speaker,…) 19 Capturing (Scanner, Microphone,…) 20 0bject Transfer (v-Inbox, v-Folder,…) 21 Audio (Speaker, Microphone, Headset service,…) 22 Telephony (Cordless telephony, Modem, Headset service,…) 23 Information (WEB-server, WAP- server,…) TABLE 1.2:MAJOR SERVICE CLASSES [Ref #1 As defined in See Generic Access Profile, Bluetooth SIG] 2. MAJOR DEVICE CLASSES The Major Class segment is the highest level of granularity for defining a Bluetooth Device. The main function of a device is used for determining the major Class grouping. There are 32 different possible major classes. The assignment of this Major Class field is defined in Table1.3. 1 2 1 1 1 0 9 8 Major Device Class 0 0 0 0 0 Miscel laneous [Ref #2] 0 0 0 0 1 Computer (desktop, notebook, PDA, organizers,…) 0 0 0 1 0 Phone (cellular ,cordless ,payphone, modem,…) 0 0 0 1 1 LAN/Network Access point 0 0 1 0 0 Audio/Video (headset, speaker, stereo, video display, vcr …) 0 0 1 0 1 Periphereal (mouse, joystick, keyboards.…) 0 0 1 1 0 Imaging (printing, scanner, camera, display,…) 1 1 1 1 1 Uncategorized, specific device code not specified XXXX All other values reserved TABLE 1.3: MAJOE DEVICE CLASSES [Ref #2:Used where a more specific Major Device Class is not suited (but only as specified as in this document) .Devices that do not have a major class assigned can use the all-1 code until’ classified’] 3. THE MINOR DEVICE CLASS FIELD The’ Minor Device Class field’ (bits 7 to 2 in the CoD ), are to be interpreted only in the context of the Major Device Class (but interpreted of the Service Class field). Thus the meaning of the bits may change, depending on the value of the ’ Major Device Class field’. When the Minor Device Class field indicates a device class ,then the primary decvice class should be reported, e. g . a cellular phone that can work as a cordless handset should 4. MINOR DEVICE CLASS FIELD–COMPUTER MAJOR CLASS Minor Device Class 7 6 5 4 3 2 bit no of CoD 0 0 0 0 0 0 Uncategorized, code for device not assigned 0 0 0 0 0 1 Desktop workstation 0 0 0 0 1 0 Server-class computer 0 0 0 0 1 1 Laptop 0 0 0 1 0 0 Handheld PC/PDA(clam shell) 0 0 0 1 0 1 Palm sized PC/PDA 0 0 0 1 1 0 Wearable computer (Watch sized) X X X X X X All other values reserved TABLE 1.4: SUB DEVICE CLASS FIELD FOR THE’ COMPUTER ’MAJOR CLASS 5. MINOR DEVICE CLASS FIELD – PHONE MAJOR CLASS Minor Device Class 7 6 5 4 3 2 bit no of CoD 0 0 0 0 0 0 Uncategorized, code for device not assigned 000001 Cellular 0 0 0 0 1 0 Cordless 0 0 0 0 1 1 Smart phone 0 0 0 1 0 0 Wired modem or voice gateway 0 0 0 1 0 1 Common ISDN Access 0 0 0 1 1 0 Sim Card Reader X X X X X X All other values reserved TABLE1.5: SUB DEVICE CLASSES FOR THE’PHONE’ MAJOR CLASS 6. MINOR DEVICE CLASS FIELD –LAN/NETWORK ACCESS POINE MAJOR CLASS Minor Device Class 7 6 5 bit no of CoD 0 0 0 Fully available 0 0 1 1 – 17% utilized 0 1 0 1 7 - 33% utilized 0 1 1 3 3 – 50% utilized 1 0 0 5 0 – 67% utilized 1 0 1 6 7 – 83% utilized 1 1 0 8 3 – 99% utilized 1 1 1 No service available [REF #3] XXX All other values reserved TABLE1.6: THE LAN/NETWORK ACCESS POINE LOAD FACTOR FIELD [Ref #3:“Device is fully utilized and cannot accept additional connections at this time, please retry later”] The exact loading formula is not standardized. It is up to each LAN/Network Access Point implementation to determine what internal conditions to report as a utilization of communication requirement is that the box .As a recommendation, a client that locates multiple LAN/Network Access Points should attempt to connect to the one reporting the lowest load. Minor Device Class 4 3 2 bit no of CoD 0 0 0 Uncategorized (use this value if no other apply ) XXX All other values reserved TABLE1.7:RESERVED SUB-FIELD FOR THE LAN/NETWORK ACCESS POINE 7. MINOR DEVICE CLASS FIELD – AUDIO/VIDEO MAJOR CLASS Minor Device Class 7 6 5 4 3 2 bit no of CoD 0 0 0 0 0 0 Uncategorized, code not assigned 0 0 0 0 0 1 Device conforms to the Headset profile 000010 Hands-free 0 0 0 0 1 1 (Reserved ) 0 0 0 1 0 0 Microphone 0 0 0 1 0 1 Loudspeaker 0 0 0 1 1 0 Headphones 0 0 0 1 1 1 Portable Audio 0 0 1 0 0 0 Car audio 0 0 1 0 0 1 Set-top box 0 0 1 0 1 0 HiFi Audio Device 001011 VCR 0 0 1 1 0 1 Camcorder 0 0 1 1 1 0 Video Monitor 0 0 1 1 1 1 Video Display and Loudspeaker 0 1 0 0 0 0 Video Conferencing 0 1 0 0 0 1 (Reserved) 0 1 0 0 1 0 Gaming/Toy [Ref #4] X X X X X X All other values reserved [Ret #4: Only to be used with a Gaming/Toy device that makes audio/video capabilities available via Bluetooth] TABLE 1.8: SUB DEVICES FOR THE ’AUDIO/VIOEO’MAJOR CLASS 8. MINOR DEVICE CLASS FIELD – PERIPHERAL MAJOR CLASS Minor Device Class 7 6 bit no of CoD 0 1 Keyboard 1 0 Pointing device 1 1 Combo keyboard /pointing device X X X All other values reserved TABLE1.9: THE PERIPHERAL MAJOR CLASS KEYBOARD/POINTING DEVICE FIELD Bits 6 and 7 independently specify mouse, keyboard or combo mouse/keyboard devices. These may be combined with the lower bits in a multifunctional device. Minor Device Class 5 4 3 2 bit no of CoD 0 0 0 0 Uncategorized device 0 0 0 1 Gamepd 0 0 1 1 Remote control 0 1 0 0 Sensing device 0 1 0 1 Digitizer tablet X X X X All other values reserved TABLE1.10: RESERVED SUB-FIELD FOR THE DEVICE TYPE 9. MINOR DEVICE CLASS FIELD – IMAGING MAJOR CLASS Minor Device Class 7 6 5 4 bit no of CoD X X X 1 Display X X 1 X Camera X 1 X X Scanner 1 X X X Printer X X X X All other values reserved TABLE 1.11: THE TMAGING MAJOR CLASS BITS 7 TO 7 Bits 4 to 7 independently specify bi splay, camera, scanner or printer. These may be combined in a multifunctional device. Minor Device Class 3 2 bit no of CoD 0 0 Uncategorized, default X X All other values reserved TABLE 1. 12: THE IMAGING MAJOR CLASS BITS 2 AND 3 Bits 2 and 3 are reserved Appendix 3: (The Inquiry Access Codes) The General-and Device-Specific Inquiry Access Codes (DIACs) The Inquiry Access Code is the first level of filtering when finding Bluetooth devices. The main purpose of defining multiple IACs is to limit the number of responses that are received when scanning devices within range. 0. 0x9E8B33 ---- General/Unlimited Inquiry Access Code(GIAC) 1. 0x9E8B00 ---- Limited Dedicated Inquiry Access Code(LIAC) 2. 0x9E8B01 ～ 0x9E8B32 RESERVED FOR FUTURE USE 3. 0x9E8B34 ～ 0x9E8B3F RESERVED FOR FUTURE USE The Limited Inquiry Access Code(LIAC)is only intended to be used for limited time periods in scenarios where both sides have been explicitly caused to enter this state, usually by user action. For further explanation of the use of the LIAC, please refer to the Generic Access Profile. In contrast it is allowed to be continuously scanning for the General Inquiry Access Code (GIAC)and respond whenever inquired.