Renishaw H-1000-5071-09-A Installation guide

Add to my manuals
68 Pages

advertisement

Renishaw H-1000-5071-09-A Installation guide | Manualzz

UCC T3 installation guide http://www.renishaw.com

UCC T3 installation guide

Document part number H-1000-7578-01-A

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 1 of 68

UCC T3 installation guide http://www.renishaw.com

FCC information for the UCC T3 controller

EC declaration of conformity

Renishaw plc declares that the UCC T3 complies with the applicable standards and regulations. A copy of the EC declaration of conformity is available on request.

Information to user (FCC section 15.105)

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the installation manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case you will be required to correct the interference at your expense.

Information to user (FCC Section 15.21)

The user is cautioned that any changes or modifications not expressly approved by Renishaw plc or authorised representative could void the user's authority to operate equipment.

Special accessories (FCC Section 15.27)

The user is also cautioned that any peripheral device installed with this equipment such as a computer, must be connected via a highquality shielded cable to ensure compliance with FCC limits.

WEEE

The use of this symbol on Renishaw products and/or accompanying documentation indicates that the product should not be mixed with general household waste upon disposal. It is the responsibility of the end user to dispose of this product at a designated collection point for waste electrical and electronic equipment (WEEE) to enable reuse or recycling. Correct disposal of this product will help to save valuable resources and prevent potential negative effects on the environment. For more information, please contact your local waste disposal service or Renishaw distributor.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 2 of 68

UCC T3 installation guide http://www.renishaw.com

Safety recommendations for the UCC T3 controller

Environmental conditions

Indoor use

Altitude

Operating temperature

Storage temperature

Relative humidity

Transient voltages

Pollution degree

IP30* (BS EN60529:1992) up to 2000 m

+5 °C to +50 °C

­25 °C to +70 °C

80% maximum (non­condensing) for temperatures up to +31 °C

Linear decrease to 50% at +40 °C

Installation category II

2

NOTE: It may be necessary to house UCC T3 in a suitable electrical enclosure according to the installation's environmental conditions to obtain a higher IP rating.

NOTE:  For ambient temperatures under 40 °C, maximum input power for the UCC T3 is 800 W. For temperatures between 40 °C and 50 °C the maximum power is 400 W.

WARNING:  UCC T3 is not recommended for use in ambient temperatures above 50 °C.

WARNING: Earthing provision for the complete machine is the responsibility of the OEM or installer.

WARNING: Isolation: UCC T3 is isolated from the DC power supply by disconnection of the power connector. If any additional means of isolation is required, it must be specified and fitted by the machine manufacturer or the installer of the product. The isolator must be sited within easy reach of the CMM operator and comply with IEC61010 and any applicable national wiring regulations for the country of installation.

WARNING: The PSU must be single fault tolerant, approved to EN60950-1 and must be connected to a supply incorporating a protective earth conductor. Earthing provisions and residual fault protection for the complete machine are the responsibility of the

OEM or installer.

Machine safety

WARNING: Switching off or isolating the UCC T3 may NOT prevent unexpected machine movement. The user is advised to isolate the machine from the electricity supply, compressed air or other energy sources in accordance with the machine manufacturer's instructions before entering the danger zone or performing any maintenance operations.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 3 of 68

UCC T3 installation guide http://www.renishaw.com

If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

The emergency stop safety system that has been integrated into the UCC T3 controller is designed to achieve category 2 to standard BS

EN ISO13849-1:2008, this can be hardware configured to obtain category B. The risk assessment made by the system installer on the installation should therefore have determined which category is required.

The UCC T3 must only be commissioned through Renishaw software, failure to do so may result in unexpected machine movement.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 4 of 68

UCC T3 installation guide http://www.renishaw.com

UCC T3 controller system overview

UCC T3 is an addition to the Renishaw CMM controller product range. UCC T3 combines the control capabilities of UCClite-2 with the servo power amplifier performance of the SPAlite, with enhancements for higher power and category 2 ESTOP.

The high power capability combined with the compact form of the UCC T3 controller-amplifier enables use across a wide range of machines.

The complete range of Renishaw two-wire kinematic touch-trigger probes is supported. Conventional contact and strain-gauge sensors and manual and motorised probe heads with appropriate probe or stylus changers are supported only with additional hardware (for example a PH10 head will need a PHC10-3 which will be connected to the serial comms port on the controller).

The UCC T3 CMM controller-amplifier has the following capabilities:

Controls three axes of a CMM

Accepts input signals from air pressure sensors, crash detectors and all axis inner and outer travel limit switches

Accepts two uncommitted general-purpose input signals and generates one uncommitted general-purpose output signal

Serial communication for use with a Renishaw PHC10 controller

Directly supports the TP1, TP2, TP6, TP20 touch-trigger probes

Indirectly supports the TP200 via an external PI 200 interface

Provides a +24 V supply for use by the CMM switches

Supports the MCUlite-2 joystick (it can also support the MCU1 and MCU5)

Provides power output of up to 800 W continuous and 960 W for up to 1 second

The voltage setting of each axis is independent, allowing differing motor voltages to be used without damage

Supports DC motors in the range 24 V to 80 V. Currents up to 10 A

Supports Encoder / Tacho or Linear Encoders (torque mode) for velocity feedback

Simulated Linear power amplifier – drive outputs are free from switching edges, eliminating noise from drive PWM improving repeatability and reducing emissions

Provides category 2 ESTOP

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 5 of 68

UCC T3 installation guide http://www.renishaw.com

Features of the UCC T3 controller

The unit has the following facilities:

Rear panel connectors for the external interface cables to and from the CMM

Rear panel USB connection for the two-way communication link to the CMM host computer

Rear panel connection for a Renishaw MCU joystick

Readhead circuitry for CMM digital measuring scales and motor encoders

Digital servo power amplifier

Status-indicating LEDs

Control electronics for probes and peripheral devices attached to the CMM

LEDs visible through the front panel of the UCC T3 enclosure indicate the operational status

Sub-circuits in the unit control the following interfaces through connectors on the rear panel of the enclosure:

USB data link to the CMM host computer

X, Y, Z axis data input from the CMM readheads

Motor drives

Connections for the TP20, TP1, TP2 and TP6 touch-trigger probes

I/O connections to limit switches, air pressure sensors and other digital inputs and outputs

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 6 of 68

UCC T3 installation guide http://www.renishaw.com

UCC T3 system components

The part numbers of the UCC T3 kits and upgrades are:

UCC T3 kits

A-5518-0001 UCC T3 controller-amplifier kit

A-5518-0501 UCC T3 controller-amplifier kit 1 comprising:

A-5518-0001 UCC T3 controller-amplifier kit

A-5331-0007 MCUlite-2 joystick

A-5518-0020 UCC T3 controller-amplifier kit 2 comprising:

A-5518-0001 UCC T3 controller-amplifier kit

A-5331-0007 MCUlite-2 joystick

A-5518-0025 PSU 600 W 60 V + cable (medium / large machines)

UCC T3 accessories

A-5518-0005 UCC T3 bracket kit

A-5518-0010 UCC T3 connector kit (including USB cable)

A-5518-0011 UCC T3 filter replacement kit

P-EA02-0021 PSU 70 W 24 V (small machines)

A-5518-0025 PSU 600 W 60 V + cable (medium / large machines)

A-5331-0007 MCUlite-2 joystick

A-5121-0003 MCU 5 joystick

A-5684-0100 PHC10-3 controller

A-5567-1622 PHC10-3 RS232 comms cable

A-5707-0100 PI 200-3 probe interface

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 7 of 68

UCC T3 installation guide http://www.renishaw.com

UCC T3 controller installation software

UCCAssist-2

The Renishaw UCCAssist-2 program is a utility to assist the engineer to install, commission and maintain a CMM system based on the UCC T3 controller-amplifier.

Capabilities of the software include:

Basic machine system diagnostics

Operation with Renishaw's machine checking gauge, enabling the user to complete frequent volumetric accuracy tests to ensure the

CMM is running within the specified operational tolerances

Automated CMM error-mapping routines, when used in conjunction with the Renishaw ML10 or XL80 laser systems

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 8 of 68

UCC T3 installation guide http://www.renishaw.com

CMM host computer for the UCC T3 controller installation

For the installation of a UCC T3 controller, the CMM host computer must use Windows XP Pro, Windows Vista or Windows 7 as an operating system and a hard disc drive with available storage space of at least 300 Mbytes. The processor speed and RAM requirements are not excessive – if the PC supports the operating system and application software, it will almost certainly support the UCC controller operation. A minimum specification of 1 GHz processor speed and 256 Mbytes RAM is recommended but please check with your application software vendor for their requirements, as they may be higher.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 9 of 68

UCC T3 installation guide http://www.renishaw.com

General wiring standards for the installation of the UCC T3 controller

To achieve reliable operation of the UCC T3 and the CMM host computer, the following should be observed:

The PSU must be single fault tolerant, approved to EN60950-1 and must be connected to a supply incorporating a protective earth conductor. Earthing provisions and residual fault protection for the complete machine are the responsibility of the OEM or installer.

The system must be PAT tested before the equipment is powered.

All signal cables MUST be screened and all cable screens should be connected electrically to the cable connector's metal shells.

It is recommended that screens for motor cables should be connected to the shell on the UCC T3 end and connected to the motor housing at the CMM end.

Signal cables such as tacho and scale cables should be connected to the UCC T3 and have a cable shield that runs to the machine but is left unconnected at the machine end.

Motor screens should be connected to both the UCC T3 and the motor housing.

Please refer to appropriate product installation guides when other Renishaw components (PH10, PI 200 etc) are integrated into the system.

All cables that are used to connect the UCC T3 to the CMM (that are not data cables) must have a minimum cross section of

0.3 mm

2

(as specified in EN 60204-1 para.12.6). UCC T3 has a maximum voltage of 80 Vdc and peak current is 10 A. The actual peak current will be dependent on the size of the motor fitted and how hard it needs to be driven, so cable sizes need to be calculated by the system installer.

All cable connectors should be secured to the UCC T3 by the connector jack screws.

The power input to the UCC T3 controller is via a 3W3 connector; refer to the Connector and signals section for more information.

UCC T3 power requirements

The UCC T3 controller requires 30 W of power to support the controller functions integrated into the unit; this must be factored into the power supply used.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 10 of 68

UCC T3 installation guide http://www.renishaw.com

UCC T3 controller troubleshooting

Fatal faults

The UCC T3 controller monitors a number of machine input/output signals and internal operational functions. If any of these reach a defined level where the system believes it is dangerous to operate, a fatal fault will be applied.

When a fatal fault is detected it is not possible to engage the servo system. There may be other faults that prevent the CMM from engaging. Not all are reported.

Reported fatal fault

Emergency stop

Air pressure

Crash

Scale failure

Overspeed

Possible cause

• Emergency stop system activated

• Internal failure of servo power amplifier

• Air pressure low

• Crash switch activated

• Scale readhead failed

• Scale “mis­count”

• Scale not connected

The position demand has exceeded an internal defined limit

• Failure of a tacho feedback

• Incorrect scale resolution

Over-temperature shutdown

The UCC T3 unit is designed for continuous power of up to 800 W. The unit will allow a supply current consumption of up to 12 A, which at

80 V is 960 W for a short period of time (1 second).

If this is sustained for a prolonged period, or the unit is not used in an adequate environment such as poor ventilation or high ambient temperature, the unit will disengage the motors to protect itself. An over-temperature warning will be reported to UCCserver.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 11 of 68

UCC T3 installation guide http://www.renishaw.com

Product generic information

Care of equipment

Renishaw probes and associated systems are precision tools used for obtaining precise measurements and must therefore be treated with care.

Changes to Renishaw products

Renishaw reserves the right to improve, change or modify its hardware or software without incurring any obligations to make changes to

Renishaw equipment previously sold.

Warranty

Renishaw plc warrants its equipment for a limited period (as set out in our Standard Terms and Conditions of Sale) provided that it is installed exactly as defined in associated Renishaw documentation.

Prior consent must be obtained from Renishaw if non-Renishaw equipment (e.g. interfaces and/or cabling) is to be used or substituted.

Failure to comply with this will invalidate the Renishaw warranty.

Claims under warranty must be made from authorised service centres only, which may be advised by the supplier or distributor.

Trademarks

Windows XP, Window 7 and Windows Vista are registered trade names of the Microsoft Corporation.

All trademarks and trade names are acknowledged.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 12 of 68

UCC T3 installation guide http://www.renishaw.com

References and associated documents

It is recommended that the following documents are referred to when installing the UCC T3 controller.

Renishaw documents

Associated documentation is available from www.renishaw.com

.

Document number

H-1000-5067

H-1000-5071

H-1000-5029

H-1000-7542

H-1000-7543

Title

MCU Installation and user's guide

PH10 Installation guide

PI 200 Installation guide

PI 200-3 Installation guide

PHC10-3 Installation guide

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 13 of 68

UCC T3 installation guide http://www.renishaw.com

Installation of the UCC T3

Mounting the UCC T3

The UCC T3 unit draws air from the right hand side when viewed from the front and expels air out of the left hand side. A minimum clearance gap of 10 mm is necessary between the sides of the unit and any potential obstruction. The dimensions shown on the above drawing are in mm (in).

Fitting mounting brackets for 19 inch rack mounting (optional)

Mounting kit (A-5518-0005)

NOTE:  The screws supplied with this kit are M5 × 6 mm countersink type.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 14 of 68

UCC T3 installation guide http://www.renishaw.com

The UCC T3 machine controller and power amplifier is an addition to the Renishaw CMM controller family of products.

The UCC T3 CMM controller offers the following machine controller capability:

3-axis CMM motion control

Comprehensive machine input and output signal capability supporting: air pressure, individual machine inner and outer limit switches, two general-purpose input signals and one general-purpose output signal

Compatibility with the Renishaw PHC10 controller

Direct interfacing support for TP1, TP2, TP6 and TP20 touch-trigger probes

Support of the Renishaw Probe Interface Connection System (PICS), PI 200 and PI7-2

A +24 V supply for use by the CMM switches

Support for up to 800 W machine power (power supply dependent)

Support of Renishaw MCUlite-2, MCU1 and MCU5 joysticks

Software configurable to a maximum of 80 V on an individual axis basis

Software configurable to a maximum of 10 A on an individual axis basi

Support for either Encoder / Tacho or Linear Encoders (torque mode) for velocity feedback

Either category 2 or category B emergency stop systems

Simulated linear power amplifier – drive outputs are free from switching edges, eliminating noise from drive PWM improves repeatability and reduces emissions

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 15 of 68

UCC T3 installation guide http://www.renishaw.com

System interconnections

The UCC T3 provides a simpler means of interconnecting many of the sub-systems (e.g. a probe head) in a measuring system.

TP2 / TP20 / TP6 - two-wire touch-trigger probe system for UCC T3 with manual probe head

TP200 touch-trigger probe system for UCC T3

PH10 probe head and two-wire touch-trigger probe system for UCC T3

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 16 of 68

UCC T3 installation guide http://www.renishaw.com

PH10 probe head and TP200 touch-trigger probe system for UCC T3

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 17 of 68

UCC T3 installation guide http://www.renishaw.com

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 18 of 68

UCC T3 installation guide http://www.renishaw.com

UCC T3 visual diagnostics

UCC T3 visual diagnostics

A visual indication of the system status is provided by four LEDs on the front panel, providing assistance in diagnosing and rectifying system faults.

LED status key Description

LED on (green/amber/red)

LED flashing off/on

X

LED flashing red/green

LED off

Any condition

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 19 of 68

UCC T3 installation guide http://www.renishaw.com

X

X

X

X

X

X

USB COMMS SERVO STATUS PROBE SEATED

X

X

X

X

X

ERROR

No power to UCC T3

Description

Download successful, amps not engaged

E-stop released, amps not engaged

Download failed, power cycle required

E-stop active

Axes engaged

Dynamic braking

Scale error

X

UCC T3 start-up process

When powered on, a self-test and initialisation is performed.

USB COMMS

O

SERVO STATUS

O

PROBE SEATED

O

ERROR Description

No power to UCC T3

O

Power applied to UCC T3

O O

Waiting for download

O O

If any of the tests fail, the failure mode is indicated on the status LEDs after about 15 seconds. When power cycling, a minimum of 10 seconds is recommended between power removal and reconnection.

After the UCC T3 has completed its self-test, the system is ready for the software to be downloaded. The sequence of the status LEDs is shown below.

USB Comms Active Servo Status Probe Seated Error Description

O O Waiting for download

X

O

X

Downloading, USB data being passed

O Download successful

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 20 of 68

UCC T3 installation guide http://www.renishaw.com

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 21 of 68

UCC T3 installation guide http://www.renishaw.com

Connecting the UCC T3 to the host PC

USB connection

Renishaw's UCCsuite software includes all the necessary drivers and utilities to permit the system to be commissioned and operate under the I++ DME interface protocol. The UCC T3 communicates to the host PC using a USB1.1 communication link. This limits the maximum

USB cable distance between the units to 5 m.

Software installation

The UCC T3 controller is supported on UCCsuite version 4.4.5 software or later.

The UCCsuite software is automatically installed when the application is run.

The software can be obtained online at www.renishaw.com/cmmsupport or from your local Renishaw supplier.

Follow the prompts to install the UCCserver software by clicking on the “Next or “Yes” buttons as appropriate.

When the “Installation successfully completed” screen appears, you are ready to connect your UCC T3.

Earth bonding scheme to achieve an adequate level of protective earthing and RF immunity

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 22 of 68

UCC T3 installation guide http://www.renishaw.com

Connectors and signals for the UCC T3 controller

Rear panel

The connectors on the rear panel of the UCC T3 controller enclosure are shown below:

DC power in

3W3 socket. The UCC T3 controller is powered from an external DC power source through this connector, which can be purchased in a connector kit from Renishaw.

Pin

A1

A2

A3

Function

0 V

24 V – 80 V

Reserved

DC power specification

• Voltage 24 V to 80 V

• Current input to 10 A

The UCC T3 controller requires 30 W of power to support the controller functions integrated into the unit. This must be factored into the power supply used.

CAUTION:  For ambient temperatures between 40 °C and 50 °C, the maximum input power should be 400 W.

CAUTION:  UCC T3 is not recommended for use in ambient temperatures above 50 °C.

Regenerating loads

The UCC T3 controller can be attached to motors that cause a regeneration of voltage during the deceleration stage of machine motion.

The system integrator must ensure that the power supply used in the installation will permit any regenerative voltage to be accepted without failure.

NOTE: If the power supply is not able to withstand this regenerative voltage from the motors, then a suitable diode must be wired in

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 23 of 68

UCC T3 installation guide http://www.renishaw.com

series with the positive supply to isolate this event.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 24 of 68

UCC T3 installation guide http://www.renishaw.com

"Axis0, Axis1 and Axis2" motor drive connectors

Each motor connection is a 7W2 connector for connection of a CMM motor to the UCC T3 , as shown below:

Connector pin

A1

A2

1

2

3

4

5

Shell

Function

Positive motor connection (default)

Negative motor connection (default)

Positive tacho input (default)

Negative tacho input (default)

Ground reference

Negative tacho input (linked to pin 2)

Ground reference

Screen

The table shows the default polarity configurations for all pins.

NOTE: The motor and tacho polarities on the UCC T3 controller are software-configured during the installation process. The maximum tacho voltage is 100 V. If one terminal of the tacho is grounded, the maximum voltage is reduced to 18 V. It is recommended that a differential tacho is used.

CAUTION: The UCC T3 motor connections must be blanked off if not being used to prevent accidental contact which could result in an electric shock.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 25 of 68

UCC T3 installation guide http://www.renishaw.com

MCU connector

Supports the Renishaw MCUlite-2, MCU1, MCU5 and MCUW joysticks.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 26 of 68

UCC T3 installation guide http://www.renishaw.com

Machine I/O

The 44-way (high density) socket provides connection for the CMM I/O.

The table below details the I/O pinout:

34

35

36

37

31

32

33

27

28

29

30

23

25

26

38 to 43

44

Shell

Pin number

1

2

3

4

5

6

7 to 12

13

14

15 to 18

22

Function

+24 V DV

Air

X brake

Y brake

Z brake

Output 0

Reserved

Input 0

Input 1

Reserved

Low air

Crash

X axis outer limit

-X axis outer limit

Y axis outer limit

-Y axis outer limit

Z axis outer limit

-Z axis outer limit

X axis inner limit

-X axis inner limit

Y axis inner limit

-Y axis inner limit

Z axis inner limit

-Z axis inner limit

24 V return

Reserved

24 V return

Screen

Description

Supply provided for use on CMM switched

Output to control an air solenoid

Output to control the X brake

Output to control the Y brake

Output to control the Z brake

General-purpose output signal

General-purpose input signal

General-purpose input signal

Low air pressure switch input

Crash detector switch input

CMM X axis limit switch input

CMM X axis limit switch input

CMM Y axis limit switch input

CMM Y axis limit switch input

CMM Z axis limit switch input

CMM Z axis limit switch input

CMM X axis limit switch input

CMM X axis limit switch input

CMM Y axis limit switch input

CMM Y axis limit switch input

CMM Z axis limit switch input

CMM Z axis limit switch input

Common reference line for input and output signals

Common reference line for input and output signals

+24V DC

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 27 of 68

UCC T3 installation guide http://www.renishaw.com

+24 V DC limited to 1 A.

Air

Pin 2 will be be set low (to energise the air solenoid) on boot-up and subsequently, provided there is no air failure. They will be set high on th Is transistor output signal active low controlled by the “engage command”.

Brakes

During the commissioning process it is possible to invert the output from the brake connections from an active low signal to an active high.

General-purpose output

This is an open collector pulled down to the 0 V (24 V return) line via an NPN transistor when activated. It is suitable for driving devices in the range 5 V to 24 V with a maximum output current of 200 mA. If the output is not required, then it should be left open circuit. The output is protected for excess voltage and over-current within the controller.

Switched inputs

Two uncommitted inputs are provided. Each input is activated by being pulled down to the 0 V (24 V return line). The inputs are not optoisolated and are pulled up to 24 V via a 10 kohm resistor. These inputs can accept signal levels in the range of +5 V to +48 V, and need to be pulled below 1 V to signify a change in state.

De-clutch

This input on pin 20 should normally be pulled down to the 24 V return line, to signal to the controller that the CMM's drives are mechanically connected to the moving elements of the machine, i.e. in their normal condition. The input should be open circuit, or held high, when a CMM has been temporarily ‘de­clutched' from its drive motors to allow manual positioning. The servo system will not drive the motors in this condition and will resume control at the machine‘s position when the signal again goes low.

Low air pressure

The low air pressure signal should be connected to a suitable air pressure switch. This input is monitored by the controller and when activated will remove power from the motors by causing a system fatal fault. During the commissioning process it is possible to invert this signal from an active low signal to an active high. If this capability is not required for integration to the system, then it should be connected to the 0 V (24 V return line).

Crash

The crash signal is used to inform the UCC T3 of a collision of the mechanical structure of the machine. Typically this is a sensor that is fitted to the end of the CMM quill and if activated will remove power from the motors by causing a system fatal fault.

During the commissioning process it is possible to invert this signal from an active low signal to an active high. If this capability is not required for integration to the system, then it should be connected to the 0 V (24 V return line).

Limit switches

The UCC T3 controller supports both inner and outer limit switches for all directions of machine axes. During the commissioning process it is possible to invert this signal from an active low signal to an active high. If this capability is not required for integration to the system, then it should be connected to the 0 V (24 V return line).

Inner limit switches

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 28 of 68

UCC T3 installation guide http://www.renishaw.com

If an inner limit is activated, the UCC T3 system will perform a maximum movement deceleration in all axes to a stop and then perform a controlled axis back-off in the opposite direction as if a trigger event occurred.

Outer limit switches

If an outer limit is activated the UCC T3 system will immediately disengage all servo power to the machine drives. Recovery of this error is only possible by removing the outer limit switch activation, i.e. by moving the machine off the switch.

0V (24 V return)

This is the 0 V reference for all the I / O signals.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 29 of 68

UCC T3 installation guide http://www.renishaw.com

E-STOP

The E-STOP connector is provided to allow connection of an external EMERGENCY STOP switch into the UCC T3 system. The machine manufacturer or product installer must perform a risk assessment to determine the requirements for emergency stopping and emergency switching off. The UCC T3 emergency stop safety system is designed to achieve category 2 or category B implementation as selected by the installer's risk assessment (refer to BS EN ISO13849-1:2008 para. 5.2.2).

The connection on the UCC T3 is a 9WD plug connector with the following connections:

6

7

4

5

8

9

2

3

Pin number

1

Function

E-STOP A (+24 V)

Not connected

Not connected

E-STOP B1

Not connected

E-STOP A (+24 V)

E-STOP B2

Not connected

RESET

 E­STOP connector – view on face of socket (rear of plug)

E-STOP electrical characteristics

Any emergency stop components fitted to this connector must have the following electrical characteristics:

Emergency stop system voltage: 24 V

Emergency stop system current: 1 A

All connections to this connector should be fitted by a competent technician or engineer and all wires should be sleeved. Any emergency stop devices added to the E­STOP chain should meet the requirements of IEC 60947­5­1 (Low­voltage switchgear and control gear –

Part 5­1: Control circuit devices and switching elements – Electromechanical control circuit devices) or UL1054 (Standard for special­use switches).

NOTE: If there are no additional emergency stop devices to be added to the system, connect pin 1 to pin 4, and pin 6 to pin 7 to permit the UCC T3 emergency stop switch to function.

NOTE: If the RESET signal is not used, connect pin 6 (E-STOP A) to pin 9 (RESET).

If indicated by the user's risk assessment, a ‘manual reset' button (refer to BS EN ISO13849­1:2008 para. 5.2.2.) should be included in the emergency stop system. A reset switch is required when there is limited visibility of the danger zone from the control position. The reset

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 30 of 68

UCC T3 installation guide http://www.renishaw.com

switch must be positioned outside the danger zone and in a safe position from which it may be determined that no person is within the danger zone before resetting the safety system.

NOTE: Periodically cycle E-STOP buttons, reset push buttons and check for correct position.

The E-STOP buttons should be cycled regularly by operators to ensure correct operation, the frequency of testing having been determined by user risk assessment.

If the reset push button has been fitted, it should be tested regularly by operators to ensure correct operation, the frequency of testing having been determined by user risk assessment.

CAUTION: It is strongly recommended that the CMM manufacturer or retrofitter includes a periodic test of the emergency stop and, if fitted, the associated reset switch, in their maintenance instructions.

E-STOP with reset implementation

There are five methods of implementing the E-STOP circuit.

Single pole E-STOP E-STOP button with reset.

Dual pole E-STOP button with reset.

E-STOP without reset implementation

Single pole E-STOP button without reset.

Dual pole E-STOP button without reset.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 31 of 68

UCC T3 installation guide http://www.renishaw.com

Bypass plug

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 32 of 68

UCC T3 installation guide http://www.renishaw.com

Serial Comms: RS232

This connector is for use with a Renishaw motorised head controller (PHC10-3). Further details can be found in the Renishaw PHC10 installation guide H-1000-5071.

4

5

6

Pin number

1

2

3

7

8

9

Shell

Function

Not connected

Rx

Tx

DTR (high)

0 V GND

Not connected

RTS

CTS

Not connected

Screen

Serial comms – view on face of socket (rear of plug)

Communication settings

This port is configured for the following communication settings:

Baud rate

Data

Parity

Stop

9600

7 bits

Even

1 bit

Connection to a PHC10-3

To connect a PHC10-3 to the controller, the following settings are needed:

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 33 of 68

UCC T3 installation guide http://www.renishaw.com

PHC10-3 dip switches

1

U

2

D

3

U

4

D

5

D

6

D

7

D

8

D

9

U

10

D

11

U

12

U

13

U

The cable connection for a PHC10-3 to a UCC T3 is as detailed below or can be purchased from Renishaw, part number A-5567-1622.

PHC10-3

25 way D connector

Pin 2

Pin 3

Pin 4

Pin 5

Pin 7

Signal

Tx →

Tx ←

RTS → CTS

CTS ← RTS 

Ground

UCC T3

9 way D connector

Pin 2

Pin 3

Pin 8

Pin 7

Pin 5

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 34 of 68

UCC T3 installation guide http://www.renishaw.com

PICS connector

The PICS connector can either be:

Connected directly to the probe – in this configuration the UCC T3 will operate as the probe interface.

Connected to a probe interface (PI 200) – in this configuration the UCC T3 will accept the trigger signals from the unit.

The connector is a 9-pin D socket, pinout as follows:

Pin number

1

2

3

6

7

4

5

8

9

Shell

Function

PICS STOP

PICS probe power off (PPOFF)

0 V

PICS LED anode

Probe signal

Reserved

PICS probe damping (PDAMP)

PICS LED off (LEDOFF)

Probe common

Screen

PICS connector – view of face of socket (rear of plug) 

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 35 of 68

UCC T3 installation guide http://www.renishaw.com

Scale inputs

Provides RS422 compatible scale inputs for each of the machine axes through the 15 W HDD connectors.

NOTE: If the machine scale is of a different format (e.g. analogue, single-ended), then this will require an external adaptor.

10

11

12

13

7

8

9

5

6

3

4

Pin number

1

2

14

15

Shell

Function

External N/C

0 V supply

- Error

- Reference mark

- B signal

- A signal

+ 5.25 V supply

Reserved

+ Error / limit switch Q

Limit switch P

+ Reference mark

+ B signal

+ A signal

Inner screen

Scale supply voltage is 5.25 V at 350 mA from each readhead connector. Scale quadrature signals with ideal waveforms and phase displacement with an edge rate of up to 40 MHz.

Scale input signals to be to EIA specification RS-422:

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 36 of 68

UCC T3 installation guide http://www.renishaw.com

UCC T3 input circuits for CMM readhead – scale and reference mark inputs

UCC T3 error interface circuit

Supports the error signal as integrated to the Renishaw range of RGH24 readheads. If the error signal is not integrated into the connected readhead, then it is necessary to configure the connection as indicated below.

-error (pin 3) link to 5.25 V (pin 7)

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 37 of 68

UCC T3 installation guide http://www.renishaw.com

Limit switch interface circuit

Scale based limit switch error signals are as integrated to the Renishaw range of RGH24 readheads.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 38 of 68

UCC T3 installation guide http://www.renishaw.com

Encoder

Encoder based feedback for motor speed sensing via high density 15­way ‘D' sockets which are designed to accept RS422 compliant signals.

12

13

14

15

Shell

8

9

10

11

6

7

4

5

Pin number

1

2

3

Function

Not connected

0 V supply

Not connected

Not connected

- B signal

- A signal

+ 5V supply

+ 5V supply

0 V supply

Not connected

Not connected

Not connected

+ B signal

+ A signal

0 V supply

Screen

Supply 5.25 V at 350 mA from each encoder connector.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 39 of 68

UCC T3 installation guide http://www.renishaw.com

EXT SSC

No connection required.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 40 of 68

UCC T3 installation guide http://www.renishaw.com

Maintenance

Filter replacement

The UCC T3 controller has a positive air flow within its enclosure for cooling purposes; this system has a replaceable filter to protect it from the ingress of dust. The machine operator should check the condition of this filter on a regular basis. It is recommended that this filter is removed and checked then replaced as necessary during the machine installer or retrofitter's regular maintenance routine.

Exchanging / removing the air filter

The following procedure is recommended when exchanging / removing the air filter:

1. Remove power from the controller.

2. Remove the 19 inch rack mounting brackets (if fitted) by removing the two fixing screws.

3. Individually pull the heads of both the filter-retaining clips away from the unit about 5 mm for them to disengage.

This should permit the external filter cover to be pulled away.

4. Remove the filter material from the filter recess.

5. Replace the filter, reversing the steps given above. (The part number of the replacement filter is A-5518-0011).

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 41 of 68

UCC T3 installation guide http://www.renishaw.com

Renishaw address

Renishaw plc

New Mills

Wotton-under-Edge

Gloucestershire

GL12 8JR

United Kindom

+44 1453 524524

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 42 of 68

UCC T3 installation guide http://www.renishaw.com

UCC T3 Installation guide appendix 1 – International safety recommendations

BG: Препоръки за безопасност за контролера UCC T3

Условия на околната среда

Използване на закрито

Височина

Работна температура

Температура за съхранение

Относителна влажност

IP30* (BS EN60529:1992) до 2 000 м

От +5 °C до +50 °C

От ­25 °C до +70 °C

80% максимум (без кондензация) при температури до +31 °C

Линейно намаление до 50% при +40 °C

Преходни напрежения

Степен на замърсяване

Installation category II

2

ЗАБЕЛЕЖКА: Може да се наложи да се сложи UCC T3 в подходящ електрически изолиран корпус съобразно условията на околната среда на инсталацията за получаване на по­висок клас на защита IP.

ЗАБЕЛЕЖКА: За околни температури под 40 градуса по Целзий, максималната входна мощност за UCC T3 е 800 Вт. При температури между 40 °C и 50 °C максималната мощност е 400 Вт.

ПРЕДУПРЕЖДЕНИЕ: UCC T3 не се препоръчва за употреба при температури над 50 °C.

ПРЕДУПРЕЖДЕНИЕ: Осигуряването на условия за заземяване на комплектната машина е отговорност на производителя на оригиналното оборудване или монтажника.

ПРЕДУПРЕЖДЕНИЕ: Изолация: UCC T3 се изолира от постояннотоковото захранване чрез откачване на съединителя на захранването. Ако се изискват допълнително средство за изолиране, то трябва да бъде посочено и монтирано от производителя на машината или монтажника на изделието. Изолаторът трябва да е разположен с лесен достъп до него от оператора на КИМ и да отговаря на IEC61010 и всяка приложима нормативна уредба за опроводяване в страната на монтажа.

ПРЕДУПРЕЖДЕНИЕ: Захранващото устройство трябва да бъде толерантно към единични грешки, одобрено по EN60950­1 и трябва да бъде свързано със захранване, включващо защитен заземителен проводник. Осигуряването на условия за заземяване и защита от остатъчни грешки на комплектната машина е отговорност на производителя на оригиналното оборудване или монтажника.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 43 of 68

UCC T3 installation guide http://www.renishaw.com

Безопасност на машината

ПРЕДУПРЕЖДЕНИЕ: Изключването или изолирането на UCC T3 НЕ може да предотврати неочаквано движение машина.

На потребителя се препоръчва да изолира устройството от електрозахранването, сгъстен въздух или други източници на енергия в съответствие с инструкциите на производителя на машината, преди да влезе в опасната зона, или да извършва някакви дейности по поддръжка.

Ако оборудването се използва по начин, който не е указан от производителя, осигуряваната от оборудването защита може да се влоши.

Предпазната система за аварийно спиране, която е вградена в контролера UCC T3, има за цел да постигне категория 2 по стандарт BS EN ISO13849­1:2008, като това може да бъде конфигуриран хардуер за получаване на категория B. Оценката на риска от страна на монтажника на инсталацията е трябвало да определи коя категория е необходима.

UCC T3 трябва да бъде въведен в експлоатация само чрез софтуера на Renishaw, като неизпълнението на това изискване може да доведе до неочаквано движение на машината.

CS: Bezpečnostní doporučení pro řídicí systém UCC T3

Podmínky prostředí

Pro vnitřní použití

Nadmořská výška

Rozsah pracovních teplot

Rozsah skladovacích teplot

IP30* (BS EN60529:1992) až 2 000 m

+5 °C až +50 °C

­25 °C až +70 °C

Relativní vlhkost

Maximálně 80% (nekondenzující) pro teploty do +31 °C

Lineární pokles na 50% při +40 °C

Přechodná napětí

Stupeň znečištění

Installation category II

2

POZNÁMKA: Může být zapotřebí umístit systém UCC T3 do vhodného elektrického krytu podle podmínek prostředí instalace, abyste docílili vyšší třídy krytí IP. 

POZNÁMKA: Při teplotách okolí pod 40 °C je maximální příkon systému UCC T3 800 W. Při teplotách mezi 40 °C a 50 °C je maximální příkon 400 W.  

UPOZORNĚNÍ: Nedoporučuje se používat systém UCC T3 při teplotách okolí nad 50 °C. 

UPOZORNĚNÍ: Za zajištění uzemnění celého stroje odpovídá výrobce OEM nebo ten, kdo ho instaluje. 

UPOZORNĚNÍ: Odpojení: Systém UCC T3 se odpojuje od napájení stejnosměrným proudem odpojením napájecího konektoru. Je­li

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 44 of 68

UCC T3 installation guide http://www.renishaw.com

zapotřebí další prostředek pro odpojení, musí být specifikován a instalován výrobcem stroje nebo tím, kdo produkt instaluje.

Odpojovací prvek musí být umístěn ve snadném dosahu obsluhy souřadnicového měřicího stroje a splňovat normu IEC61010 a všechny příslušné státní předpisy pro zapojení platné v zemi instalace. 

UPOZORNĚNÍ: Napájecí zdroj musí být odolný vůči jednoduchým poruchám, schválený podle normy EN60950­1 a musí být připojený k napájení vybavenému ochranným zemnicím vodičem. Za zajištění uzemnění a ochranu před zbytkovou chybou pro celý stroj odpovídá výrobce OEM nebo ten, kdo ho instaluje. 

Bezpečnost stroje

UPOZORNĚNÍ: Vypnutí nebo odpojení systému UCC T3 NEMUSÍ zabránit nečekanému pohybu stroje. Uživateli se doporučuje odpojit stroj od elektrického napájení, přívodu stlačeného vzduchu nebo jiných zdrojů energie v souladu s pokyny výrobce stroje dříve, než vstoupí do nebezpečného prostoru nebo bude provádět jakékoliv činnosti údržby. 

Pokud je zařízení používáno způsobem, který není specifikován výrobcem, může dojít ke snížení ochrany poskytované zařízením.

Bezpečnostní systém pro nouzové zastavení zabudovaný do řídicího systému UCC T3 je navržen pro dosažení kategorie 2 podle normy

BS EN ISO13849­1:2008, konfigurací hardwaru lze dosáhnout kategorie B. Vyhodnocení rizik provedené při instalaci tím, kdo systém instaluje, musí tedy určit, která kategorie je zapotřebí.

Systém UCC T3 musí být uveden do provozu pouze pomocí softwaru společnosti Renishaw, nedodržení této podmínky může způsobit nečekaný pohyb stroje.

DA: Sikkerhedsanbefalinger for UCC T3-styring

Miljømæssige forhold

 Indendørs brug

 Højde

Driftstemperatur

Opbevaringstemperatur

Relativ fugtighed

IP30* (BS EN60529:1992)

op til 2000 m

 +5 °C til +50 °C

 ­25 °C til +70 °C

 80% maksimum (ikke­kondenserende) for temperaturer op til +31 °C

Lineær reduktion til 50% ved +40 °C

 Transiente spændinger

Forureningsgrad

Installation category II

2

BEMÆRK: Det kan være nødvendigt at anbringe UCC T3 i en egnet elektrisk indkapsling i overensstemmelse med de miljømæssige forhold ved installationen for at opnå en højere IP­værdi. 

BEMÆRK: For omgivelsestemperaturer under 40 °C er den maksimale indgangseffekt for UCC T3 800 W. For temperaturer mellem 40 °C og 50 °C er den maksimale effekt 400 W. 

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 45 of 68

UCC T3 installation guide http://www.renishaw.com

ADVARSEL:  UCC T3 anbefales ikke til brug ved omgivelsestemperaturer over 50 °C. 

ADVARSEL:  Ansvaret for bestemmelserne om jordforbindelse for hele maskinen ligger hos OEM eller installatør. 

ADVARSEL:  Isolation: UCC T3 isoleres fra DC­strømforsyningen ved frakobling af strømstikket. Hvis der kræves yderligere måder at afbryde strømforsyningen på, skal de være specificeret og monteret af maskinproducenten eller installatøren af produktet.

Afbryderen skal være placeret, så CMM­operatøren nemt kan nå den, og den skal overholde IEC61010 og eventuelle andre relevante nationale regulativer for ledningsføring i det land, hvor installationen foretages. 

ADVARSEL:  Strømforsyningen (PSU) skal være fejltolerant overfor enkelt­fejl, godkendt af EN60950­1 og tilsluttet til en strømforsyning med en beskyttende jordforbindelse. Ansvaret for bestemmelserne om jordforbindelse og fejlstrømsbeskyttelse for hele maskinen ligger hos OEM eller installatør. 

Maskinsikkerhed

ADVARSEL:  Slukning eller isolation af UCC T3 forhindrer muligvis IKKE uventet bevægelse af maskinen. Det anbefales at brugeren isolerer maskinen fra el­forsyning, trykluft eller andre energikilder i overensstemmelse med maskinproducentens vejledning, før vedkommende går ind i en farezone eller foretager nogen form for vedligeholdelse. 

Hvis udstyret anvendes på en måde, som ikke er specificeret af producenten, kan udstyrets beskyttelse blive påvirket.

Nødstopsystemet, der er blevet integreret i UCC T3­styringen, er designet til at opnå kategori 2 i standard BS EN ISO13849­1:2008.

Dette kan være hardwarekonfigureret for at opnå kategori B. Den risikovurdering, der er foretaget af systeminstallatøren, har derfor fastlagt, hvilken kategori der er nødvendig.

UCC T3 må kun idriftsættes via Renishaw software – i modsat fald kan der ske uventet bevægelse af maskinen.

DE: Sicherheitsempfehlungen für die UCC T3‐Steuerung

Umgebungsbedingungen

Einsatz im Haus/Messraum

Höhe ü.NN

Zulässiger Temperaturbereich im Betrieb

Zulässiger Temperaturbereich für die Lagerung

Relative Luftfeuchtigkeit

IP30* (BS EN60529:1992) bis 2.000 m

+5 °C bis +50 °C

­25 °C bis +70 °C

Max. 80% (nicht kondensierend) für Temperaturen bis zu +31 °C

Linearer Abfall auf 50% bei +40 °C

Kurzzeitige Überspannungen

Verschmutzungsgrad

Installation category II

2

HINWEIS:  Je nach Umgebungsbedingungen am Aufstellort ist die UCC T3­Steuerung möglicherweise in einem geeigneten

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 46 of 68

UCC T3 installation guide http://www.renishaw.com

Elektrogehäuse unterzubringen, um eine höhere IP­Schutzklasse zu erreichen. 

HINWEIS:  Bei Umgebungstemperaturen unter 40 °C beträgt die maximale Eingangsleistung für die UCC T3 800 W. Bei

Temperaturen zwischen 40 °C und 50 °C beträgt die maximale Spannungsversorgung 400 W. 

ACHTUNG:  UCC T3 sollte nicht in Umgebungstemperaturen über 50 °C eingesetzt werden. 

ACHTUNG:  Für die Erdung der kompletten Maschine ist der Maschinenhersteller bzw. Installationstechniker verantwortlich. 

ACHTUNG:  Isolierung: UCC T3 wird durch Abziehen des Netzgerätesteckers von der Spannungsversorgung getrennt. Wird eine weitere Abschaltmöglichkeit benötigt, ist diese zu spezifizieren und vom Maschinenhersteller oder Installationstechniker für das

Produkt einzubauen. Der Trennschalter muss für den CMM­Bediener leicht erreichbar sein und IEC61010­Bestimmungen, wie auch alle anderen gültigen nationalen Verdrahtungsvorschriften im Installationsland erfüllen. 

ACHTUNG:  Das Stromversorgungsmodul muss das Kriterium der Einzelfehlertoleranz erfüllen, gemäß EN60950­1 zugelassen sein und an eine Spannungsversorgung mit Schutzleiter angeschlossen werden. Für die Erdung und den weiteren Fehlerstromschutz der kompletten Maschine ist der Maschinenhersteller bzw. Installationstechniker verantwortlich.

Maschinensicherheit

ACHTUNG: Das Abschalten der UCC T3 oder Trennen ihrer Spannungsversorgung ist KEIN Schutz vor unerwarteten

Maschinenbewegungen. Der Bediener sollte, gemäß der Herstelleranweisung, die Stromversorgung, Druckluft und andere

Energiequellen der Maschine trennen, bevor er die Gefahrenzone betritt bzw. Wartungsarbeiten durchführt. 

Wird das Gerät für einen nicht vom Hersteller spezifizierten Zweck benutzt, kann dies zu einer Beeinträchtigung des vom Gerät bereitgestellten Schutzes führen.

Die in der UCC T3-Steuerung integrierte Notaus-Sicherheitsvorrichtung wurde entwickelt, um Kategorie 2 des Standards BS EN

ISO13849­1:2008 zu genügen. Über eine Konfiguration der Hardware kann Kategorie B erzielt werden. Die Risikobeurteilung, die der

Installationstechniker bei Einrichtung des Systems vorgenommen hat, sollte daher eine Angabe enthalten, welche Kategorie benötigt wird.

Die UCC T3 darf ausschließlich durch Renishaw Software betrieben werden. Die Nichtbeachtung dieser Vorschrift kann zu unerwarteten

Maschinenbewegungen führen.

EL: Συστάσεις ασφαλείας για τον ελεγκτή UCC T3

Περιβαλλοντικές συνθήκες

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 47 of 68

UCC T3 installation guide http://www.renishaw.com

Χρήση σε εσωτερικό χώρο

Υψόμετρο

Θερμοκρασία λειτουργίας

Θερμοκρασία αποθήκευσης

Σχετική υγρασία

IP30* (BS EN60529:1992) έως 2000 m

+5 °C έως +50 °C

­25 °C έως +70 °C

μέγιστο 80% (χωρίς συμπύκνωση) για θερμοκρασίες έως +31 °C

Γραμμική μείωση σε 50% στους +40 °C

Μεταβατικές τάσεις

Βαθμός μόλυνσης

Installation category II

2

ΣΗΜΕΙΩΣΗ: Ίσως απαιτείται να στεγάσετε τον UCC T3 σε ένα κατάλληλο ηλεκτρικό περίβλημα σύμφωνα με τις περιβαλλοντικές

συνθήκες της εγκατάστασης, ώστε να λάβετε μια υψηλότερη κατηγορία ΙΡ.    

ΣΗΜΕΙΩΣΗ: Για θερμοκρασίες περιβάλλοντος κάτω των 40 βαθμών Κελσίου, η μέγιστη ισχύς εισόδου για τον UCC T3 είναι 800 W.

Σε θερμοκρασίες μεταξύ 40 °C και 50 °C, η μέγιστη ισχύς είναι 400 W.  

ΠΡΟΣΟΧΗ: O UCC T3 δεν προτείνεται για χρήση σε θερμοκρασίες περιβάλλοντος άνω των 50 °C.  

ΠΡΟΣΟΧΗ: Η παροχή γείωσης για ολόκληρο το μηχάνημα είναι ευθύνη του Κατασκευαστή αρχικού εξοπλισμού ή του εγκαταστάτη.  

ΠΡΟΣΟΧΗ: Θέση εκτός τάσης: Ο UCC T3 απομονώνεται από την παροχή ισχύος συνεχούς ρεύματος (DC) αποσυνδέοντας το βύσμα

ισχύος. Εάν απαιτούνται οποιαδήποτε συμπληρωματικά μέσα απομόνωσης, πρέπει αυτά να καθοριστούν και να τοποθετηθούν από

τον κατασκευαστή της μηχανής ή από τον εγκαταστάτη του προϊόντος. Ο απομονωτής πρέπει να βρίσκεται σε σημείο εύκολα

προσβάσιμο από το χειριστή του CMM και να συμμορφώνεται με το πρότυπο IEC61010 και με οποιουσδήποτε εφαρμοζόμενους

εθνικούς κανονισμούς καλωδιώσεων για τη χώρα εγκατάστασης.  

ΠΡΟΣΟΧΗ: Το PSU πρέπει να έχει ανοχή ενός σφάλματος, έγκριση σύμφωνα με το ΕΝ60950­1 και πρέπει να έχει συνδεθεί σε

τροφοδοσία, η οποία θα περιλαμβάνει αγωγό προστατευτικής γείωσης. Η παροχή γείωσης και η υπολειπόμενη προστασία

σφάλματος για ολόκληρο το μηχάνημα είναι ευθύνη του Κατασκευαστή αρχικού εξοπλισμού ή του εγκαταστάτη. 

Ασφάλεια μηχανήματος 

ΠΡΟΣΟΧΗ: Η διακοπή ή απομόνωση του UCC T3 ΔΕΝ μπορεί να εμποδίσει μη αναμενόμενη κίνηση του μηχανήματος. Συνιστάται

στο χρήστη να απομονώνει το μηχάνημα από την ηλεκτρική τροφοδοσία, τον συμπιεσμένο αέρα ή άλλες πηγές ενέργειας σύμφωνα με

τις οδηγίες του κατασκευαστή μηχανήματος, προτού εισέλθει στην επικίνδυνη ζώνη ή προτού διεξάγει οποιεσδήποτε εργασίες

συντήρησης. 

Εάν ο εξοπλισμός χρησιμοποιείται με τρόπο μη προδιαγεγραμμένο από τον κατασκευαστή, η παρεχόμενη προστασία του εξοπλισμού

πιθανώς να παρεμποδίζεται.

Το σύστημα Σταματήματος Έκτακτης Ανάγκης το οποίο έχει ενσωματωθεί στον ελεγκτή UCC T3 είναι σχεδιασμένο ώστε να επιτυγχάνει την

κατηγορία 2 στο πρότυπο BS EN ISO13849­1:2008. Σε αυτό μπορεί να γίνει διαμόρφωση του υλικού ώστε να λαμβάνεται η κατηγορία Β.

Για το λόγο αυτό με την αξιολόγηση κινδύνου που γίνεται από τον εγκαταστάτη συστήματος κατά την εγκατάσταση πρέπει να καθορίζεται

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 48 of 68

UCC T3 installation guide http://www.renishaw.com

ποια κατηγορία απαιτείται.

Ο UCC T3 πρέπει να τίθεται σε λειτουργία μόνο μέσω του λογισμικού της Renishaw. Σε αντίθετη περίπτωση το αποτέλεσμα μπορεί να είναι

μη αναμενόμενη κίνηση του μηχανήματος.

ES: Recomendaciones de seguridad del control UCC T3

Condiciones ambientales

Uso en interiores

Altitud

Temperatura de funcionamiento

Temperatura de almacenamiento

Humedad relativa

IP30* (BS EN60529:1992) hasta 2.000 m

+5 °C a +50 °C

­25 °C a +70 °C

80% máximo (sin condensación) para temperaturas hasta +31 °C

Reducción lineal hasta el 50% a +40 °C

Voltaje de sobretensión

Nivel de contaminación

Installation category II

2

NOTA:  Dependiendo de las condiciones ambientales de la instalación, podría ser necesario ubicar el control UCC T3 en un armario eléctrico adecuado para obtener una tasa de IP superior.    

NOTA:  Para temperaturas ambientales hasta 40 °C, la potencia máxima de entrada del control UCC T3 es de 800 W. Para temperaturas entre 40 °C y 50 °C, la potencia máxima es de 400 W. 

ADVERTENCIA:  Se recomienda no utilizar el control UCC T3 con una temperatura ambiente superior a 50 °C.  

ADVERTENCIA:  Las conexiones de toma a tierra necesarias para toda la máquina son responsabilidad del fabricante de la máquina o el instalador.  

ADVERTENCIA:  Aislamiento: El control UCC T3 se aísla de la alimentación de CC desconectando el interruptor de alimentación.

Si es necesario algún otro método de aislamiento adicional, debe especificarse e instalarse por el fabricante de la máquina o el instalador del producto. El aislante se colocará en un punto de fácil acceso para el operario de la MMC, y debe cumplir la norma

IEC61010 y las regulaciones de cableado correspondientes al país de la instalación.  

ADVERTENCIA:  La unidad de alimentación o PSU debe ser tolerante a fallos sencillos, según la norma EN60950­1, y debe conectarse a la fuente de alimentación mediante un cable con protección de toma de tierra. Las conexiones de toma a tierra y la protección contra fallos residuales necesarias para toda la máquina son responsabilidad del fabricante o el instalador.  

Seguridad de la máquina

ADVERTENCIA:  Apagar o aislar el control UCC T3 NO evita necesariamente un movimiento imprevisto de la máquina. Para evitar

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 49 of 68

UCC T3 installation guide http://www.renishaw.com

movimientos imprevistos, el operario deberá desconectar la máquina de la toma eléctrica, el aire comprimido o cualquier otra fuente de energía, según las instrucciones del fabricante, antes de acceder a zonas peligrosas o realizar operaciones de mantenimiento. 

Si no se cumplen las indicaciones especificadas por el fabricante para la utilización del equipo, la protección del equipo puede resultar inutilizada.

El sistema de seguridad de parada de emergencia integrado en el control UCC T3 ha sido diseñado para cumplir la categoría 2 del estándar BS EN ISO13849­1:2008, no obstante, el hardware puede configurarse para obtener la categoría B. La categoría necesaria deberá ser determinada por el técnico de sistemas mediante la evaluación de riesgos durante la instalación.

El control UCC T3 debe utilizarse únicamente mediante el software de Renishaw, de lo contrario, pueden producirse movimientos imprevistos de la máquina.

ET: UCC T3 kontrolleri ohutusjuhend

Keskkonnatingimused

Kasutamine siseruumides

Kõrgus

Töötemperatuur

Hoidmistemperatuur

Suhteline õhuniiskus

IP30* (BS EN60529:1992) kuni 2000 m

+5 °C kuni +50 °C

­25 °C kuni +70 °C

Maksimaalselt 80% (mittekondenseeruv) kuni +31 °C temperatuuride puhul

Lineaarne vähenemine 50%­ni temperatuuril +40 °C

Siirdepinged

Saasteaste

Installation category II

2

MÄRKUS: Suurema IP­taseme saamiseks võib olla vajalik paigutada UCC T3 paigalduskoha keskkonnatingimustele vastavasse sobivasse elektrilisse ümbrisesse. 

MÄRKUS: Madalama kui 40 °C ümbritseva temperatuuri korral on UCC T3 suurim sisendvõimsus 800 W. Temperatuurivahemikus

40 °C kuni 50 °C on suurim võimsus 400 W. 

HOIATUS:  UCC T3 ei soovitata kasutada kõrgema kui 50 °C ümbritseva temperatuuri juures. 

HOIATUS:  Maandamisvõimaluste loomine masinale tervikuna on seadmete tootja või paigaldaja kohustus. 

HOIATUS:  Isolatsioon. UCC T3 on vahelduvvooluvarustusest isoleeritud voolulüliti lahtiühendamise kaudu. Kui esineb vajadus täiendavate isoleerimisviiside järele, tuleb need määratleda ja paigaldada masina tootjal või toote paigaldajal. Isolaator peab asuma koordinaatmõõtemasina operaatorile kergelt ligipääsetavas kohas ja olema kooskõlas IEC61010 ning teiste juhtmestikke puudutavate kohalduvate riiklike eeskirjadega.

HOIATUS:  PSU peab olema ühe rikke kindel, EN60950­1 kohase heakskiiduga ning ta peab olema ühendatud kaitsvat

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 50 of 68

UCC T3 installation guide http://www.renishaw.com

maandusjuhti sisaldava vooluvarustusega. Maandamisvõimaluste ja jääkrikke kaitse loomine masinale tervikuna on seadmete tootja või paigaldaja kohustus. 

Masina ohutus

HOIATUS:  UCC T3 väljalülitamine või isoleerimine EI pruugi masina ootamatut liikumist ära hoida. Kasutajal soovitatakse isoleerida masin vooluvarustusest, suruõhust või teistest energiaallikatest masina tootja instruktsioonide kohaselt enne, kui sisenetakse ohutsooni või asutakse tegema hooldustoiminguid. 

Kui seadet kasutatakse viisil, mida tootja ei ole ette näinud, võib seadme pakutav kaitse väheneda.

UCC T3 kontrollerisse sisseehitatud hädaseiskamise turvasüsteem on mõeldud saavutama standardi BS EN ISO13849­1:2008 2.

kategooriat, kuid selle riistvara on võimalik konfigureerida ka B kategooria saavutamiseks. Seetõttu peaks süsteemi paigaldaja tehtud ohtude hindamine paigalduskohale tegema kindlaks, milline on vajalik kategooria.

UCC T3 võib kasutusse võtta ainult Renishaw tarkvara abil. Sellest mitte kinnipidamine võib tuua endaga kaasa masina ootamatu liikumise.

FI: Turvallisuussuositukset UCC T3-ohjaimelle

Ympäristöolosuhteet

Käyttö sisätiloissa

Korkeus maan pinnasta

Käyttölämpötila

Varastointilämpötila

Suhteellinen kosteus

IP30* (BS EN60529:1992) enintään 2000 m

+5 °C... +50 °C

­25 °C... +70 °C

Enintään 80% (tiivistymätön) lämpötilaan +31 °C saakka

Lineaarinen pieneneminen 50%:iin saakka lämpötilassa +40 °C

Siirtojännitteet

Saastumisaste

Installation category II

2

HUOMAA:  UCC T3 saattaa olla tarpeen koteloida sopivaan sähkörasiaan asennuspaikan ympäristön olosuhteiden mukaan paremman IP-luokituksen saavuttamiseksi.

HUOMAA:  Kun ympäristön lämpötila on alle 40 °C, UCC T3­ohjaimen suurin syöttöteho on 800 W. Lämpötiloissa 40 °C ... 50 °C suurin teho on 400 W.

VAROITUS:  UCC T3­ohjainta ei suositella käytettävän yli 50 °C lämpötiloissa. 

VAROITUS: Koko koneen maadoituksen toteuttaminen on OEM-valmistajan tai asentajan vastuulla.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 51 of 68

UCC T3 installation guide http://www.renishaw.com

VAROITUS:  Eristys: UCC T3 eristetään tasavirtalähteestä irrottamalla virtaliitin. Jos muita eristämistapoja tarvitaan, ne tulee määritellä ja asentaa koneen valmistajan tai tuotteen asentajan toimesta. Eristyskytkin on sijoitettava standardin IEC61010 ja asennuspaikalla voimassa olevien sähköteknisten asennusohjeiden mukaisesti sellaiseen paikkaan, jossa se on helposti CMM­ käyttäjän ulottuvilla. 

VAROITUS:  PSU­yksikön tulee olla vikasietoinen, hyväksytty standardin EN60950­1 mukaisesti ja liitetty suojamaadoitusjohtimella varustettuun virtalähteeseen. Koko koneen maadoituksen ja muiden vikasuojauksen toteuttaminen on OEM­valmistajan tai asentajan vastuulla.

Koneen turvallisuus

VAROITUS:  UCC T3­ohjaimen kytkeminen pois päältä tai eristäminen EI välttämättä estä odottamattomia koneen liikkeitä.

Käyttäjää kehotetaan eristämään kone sähkövirtalähteestä, paineilmalähteestä ja muista energialähteistä koneen valmistajan ohjeiden mukaisesti ennen kulkemista vaaralliselle alueelle tai huoltotehtävien suorittamista.

Jos laitetta käytetään valmistajan ohjeista poikkeavalla tavalla, sen suojavaikutus voi olla puutteellinen.

UCC T3­ohjaimeen integroidut hätäpysäytysjärjestelmät ovat standardin BS EN ISO13849­1:2008 luokan 2 mukaisia, ja luokan B mukainen taso saavutetaan asianmukaisten laitekonfiguraatioiden avulla. Järjestelmän asentajan on tehtävä riskiarviointi asennuspaikalla ja määritettävä sen perusteella, mikä luokitus vaaditaan.

UCC T3­ohjaimen saa ottaa käyttöön vain Renishaw­ohjelmiston avulla, koska muussa tapauksessa voi seurauksena olla odottamattomia koneen liikkeitä.

FR: Recommandations de sécurité pour le contrôleur UCC T3

Conditions d'environnement

Utilisation intérieure

Altitude

Température d'utilisation

Température de stockage

Humidité relative

IP30* (BS EN60529:1992)

Jusqu'à 2 000 m de +5 °C à +50 °C de ­25 °C à +70 °C

80% maximum (sans condensation) pour les températures jusqu'à +31 °C

Réduction linéaire à 50% à +40 °C

Tensions transitoires

Degré de pollution

Installation category II

2

REMARQUE :  Il peut être nécessaire de mettre l'UCC T3 dans une enceinte électrique adéquate suivant les conditions d'environnement de l'installation pour obtenir un niveau IP supérieur.

REMARQUE :  Pour les températures ambiantes inférieures à 40 °C, la puissance d'alimentation maximale de l'UCC T3 est de 800

W. Pour des températures entre 40 °C et 50 °C, cette puissance est de 400 W. 

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 52 of 68

UCC T3 installation guide http://www.renishaw.com

ATTENTION :  Il est déconseillé d'utiliser l'UCC T3 à des températures ambiantes supérieures à 50 °C.

ATTENTION :  Il incombe à l'équipementier ou à l'installateur de prévoir une mise à la terre de toute la machine.

ATTENTION :  Sectionnement : L'UCC T3 est coupé de l'alimentation c.c. par déconnexion du connecteur électrique. Si un moyen de sectionnement complémentaire est nécessaire, il doit être spécifié et installé par le constructeur de la machine ou l'installateur du produit. Ce sectionneur doit être facilement accessible par l'opérateur de la MMT et conforme à la norme IEC61010 ainsi qu'à toute réglementation de câblage applicable dans le pays d'installation.

ATTENTION :  Le bloc d'alimentation doit avoir une tolérance à une panne, homologuée suivant EN60950­1, et doit être branché sur une alimentation intégrant un conducteur de terre. Il incombe à l'équipementier ou à l'installateur de prévoir une mise à la terre et une protection contre les pannes résiduelles de toute la machine.

Sécurité machine

ATTENTION :  Mettre l'UCC T3 hors tension ou l'isoler N'EXCLUE PAS des mouvements inattendus de la machine. Il est conseillé à l'utilisateur d'isoler celle­ci des alimentations électrique, d'air comprimé et d'autres sources d'énergie conformément aux instructions du constructeur de la machine avant de pénétrer dans la zone de danger ou de réaliser des opérations de maintenance.

L'utilisation de cet équipement d'une manière non spécifiée par le constructeur peut compromettre la protection dont cet équipement est pourvu.

Le système de sécurité par arrêt d'urgence intégré au contrôleur UCC T3 est conçu suivant les critères de Catégorie 2 de la norme BS

EN ISO13849­1 :2008 ; le matériel permet une configuration pour répondre à la Catégorie B. L'évaluation de risque effectuée par l'installateur lors de l'installation du système doit donc avoir déterminé la catégorie requise.

L'UCC T3 doit être mis en service exclusivement par un logiciel Renishaw car sans cela des mouvements inattendus de la machine pourraient avoir lieu.

GA: Moltaí sábháilteachta don rialaitheoir UCC T3

Dálaí timpeallachta

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 53 of 68

UCC T3 installation guide http://www.renishaw.com

Úsáid laistigh

Airde

Teocht oibriúcháin

Teocht stórála

Bogthaise choibhneasta

IP30* (BS EN60529:1992) suas go 2000 m

+5 °C go +50 °C

­25 °C go +70 °C

Uasmhéid 80% (neamh­chomhdhlúthú) do theochtaí suas go +31°C

Laghdú líneach go 50% ag +40 °C

Voltais neamhbhuana

Méid truaillithe

Installation category II

2

NÓTA: D'fhéadfadh riachtanas bheith ann UCC T3 a fheireadh in iniamh leictreach oiriúnach de réir dálaí timpeallachta an fhearais chun rátáil IP níos airde a bhaint amach.

NÓTA: I dtaca le teochtaí timpeallacha faoi 40 °C, is é 800 W cumhacht ionchuir uasmhéid don UCC T3. Is é 400 W an chumhacht uasmhéid do theochtaí idir 40 °C agus 50 °C.

RABHADH:  Níl UCC T3 molta le húsáid i dteochtaí timpeallacha níos airde ná 50 °C.

RABHADH:  Tá an OEM nó an suiteálaí freagrach as soláthairtí talmhaithe don mheaisín iomlán.

RABHADH:  Aonrú: Tá UCC T3 aonraithe ón soláthar cumhachta DC trí dhínascú den naschóir cumhachta.  Má tá aon mhodhanna aonraithe breise riachtanach, ní mór do dhéantúsóir an mheaisín nó suiteálaí an táirge é a mhionsonrú agus a shuiteáil.  Ní mór an t­ aonraitheoir a shuiteáil cóngarach don oibritheoir CMM agus é i gcomhlíonadh le IEC61010 agus le haon rialacháin náisiúnta sreangaithe infheidhmithe don tír inar suiteáiltear é.

RABHADH:  Ní mór an PSU bheith aon­lochtlamhálach, faofa chuig EN60950­1 agus é nasctha le soláthar ina bhfuil seoltóir talmhaithe cosanta. Tá an OEM nó an suiteálaí freagrach as soláthairtí talmhaithe agus cosaint lochta iarmharaigh don mheaisín iomlán.

Sábháilteacht mheaisín

RABHADH:  Tá seans ann NACH gcoiscfear gluaiseacht an mheaisín gan choinne tríd an UCC T3 a mhúchadh nó a aonrú. Moltar don úsáideoir an meaisín a aonrú ón soláthar leictreachais, ó aer comhbhrúite nó ó fhoinsí fuinnimh eile de réir treoracha ó dhéantúsóra an mheaisín sula dtéitear isteach sa chrios guaise nó sula ndéantar aon oibriúcháin chothabhála. 

Má úsáidtear an trealamh ar bhealach nach bhfuil mionsonraithe ag an déantúsóir, d'fhéadfadh an chosaint sa trealamh bheith lagaithe.

Tá an córas sábháilteachta stop éigeandála atá comhtháthaithe isteach sa rialaitheoir UCC T3 deartha le catagóir 2 a bhaint amach chuig caighdeán BS EN ISO 13849­1:2008, d'fhéadfadh é seo bheith mar earraí crua cumraithe chun catagóir B a bhaint amach. Dá bhrí sin, ba chóir go mbeadh an chatagóir atá riachtanach dearbhaithe ag an measúnú riosca a rinne suiteálaí an chórais ar an suiteáil.

Ní mór an UCC T3 bheith coimisiúnaithe trí bhogearraí Renishaw. Gan é seo a dhéanamh, d'fhéadfadh gluaiseacht an mheaisín gan choinne a tharlú.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 54 of 68

UCC T3 installation guide http://www.renishaw.com

HU: Biztonsági előírások az UCC T3 vezérlő számára

Környezeti feltételek

Beltéri használat

Tengerszint feletti magasság:

Üzemi hőmérséklet

Tárolási hőmérséklet

Relatív páratartalom

IP30* (BS EN60529:1992) max. 2000 m

+5 °C – +50 °C

­25 °C – +70 °C max 80%. (nem lecsapódó), legfeljebb +31 °C hőmérsékletig lineáris csökkenés 50%­ig +40°C hőmérsékleten

Átütési feszültség

Szennyeződés mértéke

Installation category II

2

MEGJEGYZÉS: Szükségessé válhat az UCC T3 megfelelő elektromos szekrényben elhelyezni a beszerelési környezet feltételeinek megfelelően azért, hogy magasabb IP védettségi értékek érjünk el.

MEGJEGYZÉS: 40 °C alatti környezeti hőmérséklet esetén az UCC T3 max 800 W teljesítményt vesz fel. 40 °C és 50 °C közötti hőmérséklet esetén a maximális felvett teljesítmény 400 W.

FIGYELMEZTETÉS: Az UCC T3 használata nem javasolt 50 °C feletti környezeti hőmérséklet esetén.

FIGYELMEZTETÉS: A teljes berendezés földeléséről a gyártónak vagy a telepítést végző szakembernek kell gondoskodnia.

FIGYELMEZTETÉS: Leválasztás: Az UCC T3 leválasztása az egyenáramú energiaforrásról a csatlakozó leválasztásával történik.

Ha egyéb leválasztásra lenne szükség, akkor azt a berendezés gyártójának vagy a termék beszerelőjének kell meghatároznia és beszerelnie. A leválasztónak a CMM üzemeltető számára könnyen hozzáférhető helyen kell lennie, és meg kell felelnie az IEC61010 szabványnak, illetve a területileg érvényes villamos bekötési szabályoknak.

FIGYELMEZTETÉS: A tápegységnek meg kell felelni az EN60950­1 szabvány előírásainak, és védőföldeléssel ellátott aljazthoz kell csatlakoztatni. A teljes berendezés földeléséről és a zavarvédelemről a gyártónak vagy a telepítést végző szakembernek kell gondoskodnia.

Gépbiztonság

FIGYELMEZTETÉS: Az UCC T3 kikapcsolása vagy leválasztása NEM feltétlenül akadályozza meg a berendezés váratlan mozgását. A felhasználónak le kell választania a berendezést az áramforrásról, sűrített levegőről és más energiaforrásokról a berendezés gyártói előírásainak megfelelően, mielőtt veszélyes területekre lépnének, illetve bármilyen karbantartási munkát végeznének.

A berendezés nem a gyártó által meghatározott módon történő használata befolyásolhatja a berendezés által nyújtott védelmet.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 55 of 68

UCC T3 installation guide http://www.renishaw.com

Az UCC T3 vezérlőbe integrált vészleállító biztonsági rendszer megfelel a BS EN ISO13849­1:2008 szabvány 2. kategóriájának; ez lehet a B kategória eléréséhez konfigurált hardver. A rendszer telepítője által a telepítéskor végzett kockázatfelmérésnek ezért tartalmaznia kell, hogy mely kategóriára van szükség.

Az UCC T3 kizárólag Renishaw szoftverrel telepíthető, ellenkező esetben váratlan gépmozgások léphetnek fel.

IT: Raccomandazioni di sicurezza per il controllo UCC T3

Condizioni ambientali

Per uso interno

Altitudine

Temperatura di funzionamento

Temperatura di stoccaggio

Umidità relativa:

IP30* (BS EN60529:1992) fino a 2000 m da +5 °C a +50 °C da ­25 °C a +70 °C

80% massimo (senza condensa) per temperature fino a +31 °C

Diminuzione lineare fino al 50% a +40 °C

Oscillazioni di tensione

Grado di inquinamento

Installation category II

2

NOTA:  Per ottenere una classificazione IP più elevata, potrebbe essere necessario alloggiare il controllo UCC T3 in un armadietto elettrico adeguato alle condizioni ambientali di installazione.

NOTA:  In caso di temperature ambientali inferiori a 40 °C, la potenza massima di ingresso di UCC T3 è 800 W. Se la temperatura è compresa fra 40 °C e 50 °C la potenza massima è 400 W. 

AVVERTENZA:  Si sconsiglia l'utilizzo del controllo UCC T3 in ambienti con temperature superiori a 50 °C. 

AVVERTENZA:  La responsabilità di eseguire la messa a terra dell'intera macchina è a carico dell'OEM o dell'installatore. 

AVVERTENZA: Isolamento: Per isolare elettricamente il controllo UCC T3, scollegare il connettore di alimentazione. Nel caso in cui fossero necessari ulteriori dispositivi di isolamento, sarà necessario specificare tale esigenza e richiedere al produttore della macchina o all'installatore di provvedere in tale senso. Il dispositivo di isolamento dovrà essere posizionato in un punto facilmente accessibile all'operatore della macchina CMM e dovrà risultare conforme allo standard IEC61010 e a tutte le normative nazionali sui cablaggi in vigore nel paese di installazione.

AVVERTENZA: L'alimentatore PSU deve essere conforme alla norma EN60950-1 e collegato a una sorgente di alimentazione dotata di un sistema di protezione con conduttore di messa a terra. La responsabilità di eseguire la messa a terra del sistema e delle misure di protezione per l'intera macchina è a carico dell'OEM o dell'installatore. 

Sicurezza della macchina

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 56 of 68

UCC T3 installation guide http://www.renishaw.com

AVVERTENZA: Lo spegnimento del controllo UCC T3 o la disconnessione dall'alimentazione NON garantisce che non possano esservi spostamenti imprevisti della macchina. Prima di accedere alla zona di pericolo o di eseguire operazioni di manutenzione, si consiglia di scollegare la macchina, oltre che dall'alimentazione elettrica, anche dall'aria compressa o da altre fonti di energia, in conformità alle istruzioni del produttore.  

Se utilizzato in modo non conforme a quanto specificato dal produttore, il dispositivo potrebbe non fornire il livello di protezione previsto.

Il sistema di arresto di emergenza integrato nel controllo UCC T3 è stato progettato per conformarsi alla categoria 2 dello standard BS

EN ISO13849­1:2008 e può essere configurato tramite hardware per ottenere la categoria B. La valutazione di rischio ,effettuata al momento dell'installazione, da parte del tecnico incaricato determinerà quale sia la categoria richiesta.

La messa in funzione del controllo UCC T3 deve avvenire solo tramite il software Renishaw. In caso contrario la macchina potrebbe non funzionare o generare spostamenti imprevisti.

LT: „UCC T3“ valdiklio saugos rekomendacijos

Aplinkos sąlygos

Naudoti patalpoje

Aukštis virš jūros lygio

Darbinė temperatūra

Laikymo temperatūra

Santykinis oro drėgnis

IP30* (BS EN60529:1992) iki 2 000 m nuo +5 °C iki +50 °C nuo ­25 °C iki +70 °C

Daugiausia 80% (nesikondensuojantis), esant temperatūrai iki +31 °C

Linijinis mažėjimas iki 50%, esant +40 °C

Pereinamoji įtampa

Užterštumo laipsnis

Installation category II

2

PASTABA:  siekiant išgauti aukštesnius IP parametrus, atsižvelgus į montavimo aplinkos sąlygas, „UCC T3“ gali reikėti patalpinti į tinkamą elektrinį įdėklą.

PASTABA:  kai aplinkos temperatūra nesiekia 40 °C, „UCC T3“ maksimali tiekiama galia yra 800 vatų. Esant 40 °C – 50 °C temperatūrai, maksimali galia yra 400 vatų. 

ĮSPĖJIMAS: nerekomenduojama naudoti „UCC T3“, kai aplinkos temperatūra viršija 50 °C. 

ĮSPĖJIMAS: atsakomybė dėl viso įrenginio įžeminimo tenka originalios įrangos gamintojui arba montuotojui.

ĮSPĖJIMAS: izoliavimas: atjungus maitinimo jungtį, „UCC T3“ yra izoliuotas nuo pastoviosios srovės maitinimo. Jei reikia papildomų izoliavimo priemonių, jas turi nurodyti ir sumontuoti įrenginio gamintojas arba produkto montuotojas. Skyriklis turi būti lengvai pasiekiamas koordinatinės matavimo mašinos operatoriui ir turi atitikti IEC61010 bei kitas valstybės, kurioje montuojama mašina, elektros laidų instaliacijos taisykles.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 57 of 68

UCC T3 installation guide http://www.renishaw.com

ĮSPĖJIMAS: galios tiekimo įrenginys turi būti atsparus gedimams, patvirtintas pagal EN60950­1 ir prijungtas prie maitinimo tinklo, panaudojant apsauginį įžeminimo laidininką. Atsakomybė dėl viso įrenginio įžeminimo ir liekamosios apsaugos nuo gedimų tenka originalios įrangos gamintojui arba montuotojui. 

Įrenginio sauga

ĮSPĖJIMAS: išjungus arba izoliavus „UCC T3“, gali NEPAVYKTI išvengti netikėto įrenginio pajudėjimo. Naudotojui patariama pagal įrenginio gamintojo nurodymus izoliuoti įrenginį nuo elektros tinklo, suspausto oro arba kitų energijos šaltinių, paskui galima saugiai patekti į pavojaus zoną arba atlikti bet kokius techninės priežiūros darbus.  

Jei įranga naudojama ne taip, kaip nurodo gamintojas, gali sumažėti įrangos teikiama apsauga.

„UCC T3“ valdiklyje integruota avarinio sustabdymo saugos sistema pagal BS EN ISO 13849­1:2008 yra 2 kategorijos, tačiau panaudojus techninę įrangą, ji gali būti sukonfigūruota kaip atitinkanti B kategoriją. Todėl sistemos montuotojo atliekamu įrangos rizikos vertinimu turi būti nustatoma, kuri kategorija yra reikalinga.

„UCC T3“ derinkite tik naudodami „Renishaw“ programinę įrangą; nesilaikant šio nurodymo, įrenginys gali netikėtai pajudėti.

LV: Drošības ieteikumi „UCC T3” vadāmierīcei

Apkārtējās vides nosacījumi

Lietošana telpās

Augstums

Darbības temperatūra

Uzglabāšanas temperatūra

Relatīvais mitrums

IP30* (BS EN60529:1992) līdz 2000 m no +5 °C līdz +50 °C no ­25 °C līdz +70 °C maksimums 80% (bez kondensēšanās) temperatūrā līdz +31 °C

Lineārais samazinājums +40 °C temperatūrā līdz 50%

Nestacionārais spriegums

Piesārņojuma pakāpe

Installation category II

2

PIEZĪME: lai iegūtu augstāku ierīces IP (starptautisko aizsardzības) novērtējumu atkarībā no uzstādīšanas vides nosacījumiem, iespējams, ka „UCC T3” ir nepieciešams ievietot piemērotā elektriski izolējošā apvalkā.

PIEZĪME: izmantojot temperatūrā, kas zemāka par +40 °C, maksimālā pievadāmā elektroenerģijas jauda ir 800 W. Ja temperatūra ir no +40 °C līdz +50 °C, maksimālā jauda ir 400 W.

BRĪDINĀJUMS: nav ieteicams izmantot „UCC T3”, ja apkārtējā temperatūra pārsniedz +50 °C.

BRĪDINĀJUMS: par pareizu visas ierīces zemēšanu ir atbildīgs tās ražotājs vai uzstādītājs.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 58 of 68

UCC T3 installation guide http://www.renishaw.com

BRĪDINĀJUMS: atvienošana: „UCC T3” no līdzstrāvas padeves iespējams atvienot, izmantojot strāvas savienotāju. Ja vajadzīgi papildu atvienošanas līdzekļi, tie ir jānorāda un jānodrošina ierīces ražotājam vai izstrādājuma uzstādītājam. Atvienotājam jābūt novietotam tā, lai tas būtu viegli pieejams CMM operatoram un atbilstu IEC61010 un jebkuriem saistītajiem uzstādīšanas valsts elektrotehniskajiem noteikumiem.

BRĪDINĀJUMS: nepārtrauktās barošanas avotam jābūt bojājumpiecietīgam, jāatbilst EN60950­1 standartam un jābūt pievienotam strāvas padevei ar aizsargājošu zemējuma vadu. Par pareizu visas ierīces zemēšanu un pārējās pretkļūmju aizsardzības uzstādīšanu ir atbildīgs tās ražotājs vai uzstādītājs.

Ierīces drošība

BRĪDINĀJUMS: „UCC T3” izslēgšana vai atvienošana NEGARANTĒ to, ka ierīce neuzsāks neparedzētu darbību. Pirms ieiet paaugstinātās bīstamības zonā vai uzsākt apkopes darbus, lietotājam ieteicams saskaņā ar ražotāja instrukcijām atvienot ierīci no strāvas padeves, saspiesta gaisa vai citiem enerģijas avotiem.

Ja izstrādājums tiek lietots veidā, kas neatbilst ražotāja norādītajam, ierīces nodrošinātā aizsardzība var mazināties.

„UCC T3” vadāmierīcē iebūvētā avārijas apturēšanas sistēma izstrādāta, lai atbilstu BS EN ISO13849­1:2008 standarta 2. kategorijai, un to iespējams pārveidot, lai atbilstu B kategorijas nosacījumiem. Sistēmas uzstādītājam jāveic riska novērtējums, lai noteiktu, kura drošības kategorija ir nepieciešama.

„UCC T3” drīkst pārvaldīt, izmantojot tikai „Reinshaw” programmatūru, jo pretējā gadījumā tas var izraisīt ierīces neparedzētu darbību.

MT: Rakkomandazzjonijiet dwar is‐sigurtàgħall‐UCC T3 controller

Kundizzjonijiet ambjentali

Użu fuq ġewwa

Altitudni

Temperatura tal-operat

Temperatura li fiha jista' jinħażen

Umditàrelattiva

IP30* (BS EN60529:1992) sa 2000 m

5 °C sa +50 °C

­25 °C sa +70 °C

Massimu ta' 80% (bla kondensazzjoni) għal temperaturi sa +31 °C

Tnaqqis lineari għal 50% f'temperaturata' +40 °C

Vultaġġi temporanji

Grad ta' tniġġiż

Installation category II

2

NOTA:  Jista' jkun hemm bżonn li tpoġġi l­UCC T3 ġo kompartiment elettriku adattat skont il­kundizzjonijiet ambjentali tal­installazzjoni biex tikseb IP rating ogħla.

NOTA:  Għal temperaturi ambjentali taħt l­40 °C, il­provvista massima tad­dawl tal­input għall­UCC T3 hi ta' 800 W. Temperaturi bejn l­40°C u l­50 °C, il­provvista massima tad­dawl hi ta' 400 W.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 59 of 68

UCC T3 installation guide http://www.renishaw.com

TWISSIJA:  UCC T3 mhuwiex rakkomandat għall­użu f'temperaturi ambjentali ogħla minn 50 °C.

TWISSIJA:  Il­provvedimenti tal­earthing għall­magna sħiħa huma r­responsabbiltà tal­OEM jew tal­installatur.

TWISSIJA:  Iżolament: L­UCC T3 jiġi iżolat mill­provvista tad­dawl DC billi tiskonnettja l­konnettur tal­provvista tad­dawl. Jekk ikun hemm bżonn ta' mezzi addizzjonali ta' iżolament, dawn iridu jiġu speċifikati u jiġu mmuntati mill­operatur tal­magna jew mill­installatur tal­prodott. L­iżolatur irid jitpoġġa fejn ikun jista' jintlaħaq faċilment mill­operatur tas­CMM u jrid ikun konformi ma' IEC61010 u ma' kwalunkwe regolamenti nazzjonali applikabbli dwar il­wiring għall­pajjiż fejn ikun qed jiġi installat.

TWISSIJA:  Il­PSU jrid jittollera ħsara waħda, ikun approvat skont EN60950­1 u jrid jitqabbad ma' provvista tad­dawl li tinkorpora konduttur protettiv tal­earth. Il­provvedimenti tal­earthing u l­protezzjoni minn ħsara residwa għall­magna sħiħa huma r­responsabbiltà tal-OEM jew tal-installatur.

Sigurtà tal‐magna

TWISSIJA:  Li titfi jew li tiżola l­UCC T3 jista' MA JIPPREVENIX moviment mhux mistenni tal­magna. Hu rakkomandat li l­utent jiżola l­ magna mill­provvista tad­dawl, minn arja kkompressata jew minn sorsi oħrajn ta' enerġija skont l­istruzzjonijiet tal­manifattur tal­magna qabel ma jidħol fiż­żona ta' periklu jew qabel ma jwettaq kwalunkwe xogħol ta' manutenzjoni.

Jekk it­tagħmir jintuża b'mod li ma jkunx speċifikat mill­manifattur, il­protezzjoni pprovduta mit­tagħmir tista' titnaqqas.

Is­sistema tas­sigurtà ta' waqfien ta' emerġenza li ġiet integrata fil­kontrollur tal­UCC T3 hi maħsuba biex tilħaq kategorija 2 għal standard

BS EN ISO13849­1:2008; din tista' tiġi kkonfigurata permezz tal­hardware biex tintħalaq kategorija B. Għalhekk, l­evalwazzjoni tar­riskju li tkun saret mill­installatur tas­sistema fuq l­installazzjoni, suppost li tkun stabbilixxiet liema kategorija hi meħtieġa.

L­UCC T3 irid jiġi kkummissjonat biss permezz tar­Renishaw software. Jekk tonqos li tagħmel dan, dan jista' jirriżulta f'moviment mhux mistenni tal-magna.

NL: Veiligheidsaanbevelingen voor de besturing UCC T3

Omgevingscondities

Gebruik binnenshuis

Hoogte

Omgevingstemperatuur

Opslagtemperatuur

Relatieve vochtigheid

Piekspanningen

Verontreinigingsgraad

IP30* (BS EN60529:1992)

Tot 2000 m

 +5 °C tot +50 °C

 ­25 °C tot +70 °C

Maximaal 80% (geen condensatie) voor temperaturen tot +31 °C

Lineaire afname tot 50% bij +40 °C

Installation category II

2

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 60 of 68

UCC T3 installation guide http://www.renishaw.com

OPMERKING: Het kan nodig zijn om de UCC T3 in een passende behuizing onder te brengen die bij de omgevingscondities past, om een hogere IP-waarde te verkrijgen.

OPMERKING:  Voor gebruikstemperaturen onder de 40 °C is het maximale ingangsvermogen van de UCC T3 800 W. Bij temperaturen tussen 40 °C en 50 °C bedraagt het maximale vermogen 400 W.  

WAARSCHUWING:  De UCC T3 wordt niet aanbevolen voor toepassing bij gebruikstemperaturen boven 50 °C.

WAARSCHUWING: Voor aardingsvoorzieningen voor de gehele machine is de OEM of installateur verantwoordelijk.

WAARSCHUWING: Afsluiten: De UCC T3 wordt van de gelijkstroombron afgesloten door de spanningsconnector te ontkoppelen.

Als nog een extra manier van afsluiten gevraagd wordt, dan moet die gespecificeerd en geplaatst worden door de machinefabrikant of de monteur van het product. De afsluitvoorziening moet ruim binnen het bereik van de CMM-operator aangebracht worden en voldoen aan IEC61010 en de andere elektrische regels die gelden in het land van plaatsing.

WAARSCHUWING: De voedingseenheid moet enkele-fouttolerant zijn, goedgekeurd zijn volgens EN60950-1 en worden aangesloten op een stroombron met een aardverbinding ter beveiliging. Aardingsvoorzieningen en beveiliging tegen resterende fouten voor de gehele machine zijn de verantwoordelijkheid van de OEM of installateur.

Machineveiligheid

WAARSCHUWING: De UCC T3 uitschakelen of afsluiten is GEEN garantie tegen onverwachte machinebewegingen. De gebruiker wordt geadviseerd om de machine volgens de instructies van de machinefabrikant af te sluiten van de voedingsspanning, perslucht en andere energiebronnen, en pas daarna gevaarlijke gebieden te betreden of onderhoud te verrichten.

Gebruik van de apparatuur op een manier die de fabrikant niet voorgeschreven heeft, kan het apparaat beschadigen of de bescherming beperken.

Het veiligheidssysteem met noodstop dat ingebouwd is in de besturing UCC T3, is afgestemd op realisatie van categorie 2 volgens norm

BS EN ISO13849-1:2008. Via hardwareconfiguratie is dit te veranderen in categorie B. De risicobeoordeling door degene die het systeem installeert moet daarom aangeven welke categorie vereist is.

De UCC T3 mag alleen in bedrijf gesteld worden met behulp van Renishaw software, anders kunnen zich onverwachte machinebewegingen voordoen.

PL: Zalecenia dotyczące bezpieczeństwa dla sterownika UCC T3

Warunki środowiskowe

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 61 of 68

UCC T3 installation guide http://www.renishaw.com

Urządzenie przeznaczone do użytkowania w pomieszczeniach

Wysokość nad poziomem morza

Temperatura pracy

Temperatura przechowywania

Wilgotność względna

Stopień ochrony IP30* (BS EN60529:1992) do 2000 m od +5 °C do +50 °C od ­25 °C do +70 °C maksymalnie 80% (bez kondensacji pary wodnej) w temperaturach do +31

°C liniowy spadek do 50% w temperaturze +40 °C

Napięcie przejściowe

Stopień skażenia

Installation category II

2

UWAGA:  W celu osiągnięcia wyższego stopnia ochrony, konieczne może być umieszczenie sterownika UCC T3 w odpowiedniej obudowie elektrycznej, zgodnie z warunkami środowiskowymi instalacji. 

UWAGA:  Przy temperaturze otoczenia niższej niż 40 °C, maksymalna moc wejściowa dla sterownika UCC T3 wynosi 800 W. Przy temperaturach pomiędzy 40 °C a 50 °C, maksymalna moc wejściowa wynosi 400 W. 

OSTRZEŻENIE: Nie zaleca się używania sterownika UCC T3 w temperaturze otoczenia powyżej 50 °C. 

OSTRZEŻENIE: Za zapewnienie warunków uziemienia całej maszyny jest odpowiedzialny producent maszyny lub instalator. 

OSTRZEŻENIE: Izolacja: Sterownik UCC T3 jest izolowany od zasilania prądem stałym poprzez odłączenie złącza zasilania. Gdy wymagane są jakiekolwiek dodatkowe środki odłączania, ich dane techniczne muszą być określone i muszą one być zainstalowane przez producenta maszyny lub instalatora produktu. Odłącznik musi być umieszczony w taki sposób, aby zapewniać operatorowi maszyny współrzędnościowej łatwy dostęp do niego oraz musi spełniać wymagania IEC61010 i wszelkich przepisów dotyczących okablowania, jakie obowiązują w kraju instalacji. 

OSTRZEŻENIE: Zasilacz powinien tolerować tylko “jedną usterkę”, jak określono w normie EN60950­1 i musi być podłączony do zasilania wyposażonego w przewód uziemienia ochronnego. Zapewnienie warunków uziemienia oraz ochrona przed ryzykiem resztkowym całej maszyny są odpowiedzialnością producenta sprzętu oryginalnego lub instalatora. 

Bezpieczeństwo maszyny

OSTRZEŻENIE: Wyłączenie lub odizolowanie sterownika UCC T3 może NIE zapobiec nieoczekiwanym ruchom maszyny. Zaleca się, aby przed wejściem do strefy niebezpiecznej lub wykonaniem jakichkolwiek czynności konserwacyjnych użytkownik odizolował maszynę od zasilania prądem elektrycznym, sprężonym powietrzem bądź od innych źródeł energii, zgodnie z zaleceniami producenta maszyny.

Jeżeli wyposażenie jest użytkowane w inny sposób niż określił to producent, zabezpieczenie zapewniane przez to wyposażenie może być osłabione.

Połączony ze sterownikiem UCC T3, system awaryjnego zatrzymania został zaprojektowany aby osiągnąć kategorię 2, zgodnie z normą

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 62 of 68

UCC T3 installation guide http://www.renishaw.com

BS EN ISO13849­1:2008, co można skonfigurować sprzętowo aby osiągnąć kategorię B. Ocena ryzyka wykonana przez instalatora systemu podczas instalacji powinna więc określać, która kategoria jest wymagana.

Sterownik UCC T3 powinien być uruchomiony tylko poprzez oprogramowanie firmy Renishaw. Niezastosowanie się do tego zalecenia może spowodować nieoczekiwany ruch maszyny.

PT: Recomendações de segurança para o comando UCC T3

Condições ambientais

Uso interno

Altitude

Temperatura operacional

Temperatura de armazenamento

Umidade relativa

IP30* (BS EN60529:1992) até 2000 m

+5 °C a +50 °C

­25 °C a +70 °C

80% máximo (sem condensação) para temperaturas até +31 °C

Redução linear até 50% a +40 °C

Tensões transientes 

Grau de poluição 

Installation category II

2

NOTA:  Pode ser necessário alojar o UCC T3 em um invólucro elétrico apropriado, de acordo com as condições ambientais da instalação, para obter um grau de proteção IP mais alto. 

NOTA:  Para temperaturas ambiente abaixo de 40 °C, máxima potência de entrada para o UCC T3 é 800 W. Para temperaturas entre 40 °C e 50 °C a potência máxima é 400 W. 

ATENÇÃO: O UCC T3 não é recomendado para uso em temperaturas ambiente acima de 50 °C. 

ATENÇÃO: O aterramento da máquina completa é de responsabilidade do OEM ou instalador. 

ATENÇÃO: Isolamento: O UCC T3 é isolado da alimentação DC através da desconexão do conector de potência. Se qualquer outro meio de isolamento for necessário, o mesmo deverá ser especificado e preparado pelo fabricante da máquina ou instalador do produto. O isolador deve ser de fácil acesso para o operador da MMC e atender à norma IEC61010 e todas as demais regulamentações elétricas nacionais do país onde estiver instalado. 

ATENÇÃO: A unidade de alimentação deve ser tolerante a falha singular, aprovada conforme EN60950­1 e ser conectada a uma alimentação que incorpore um condutor terra. O aterramento e a proteção contra falha residual da máquina completa são de responsabilidade do OEM ou instalador.

Segurança da máquina

ATENÇÃO: O desligamento ou o isolamento do UCC T3 pode NÃO impedir um movimento inesperado da máquina. Antes de entrar na zona de perigo ou executar trabalhos de manutenção, recomendamos que o usuário isole a máquina da alimentação

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 63 of 68

UCC T3 installation guide http://www.renishaw.com

elétrica, ar comprimido ou outras fontes de energia, de acordo com as instruções do fabricante. 

Se o equipamento for utilizado de modo não especificado pelo fabricante, a proteção oferecida poderá ser prejudicada.

O sistema de segurança de parada de emergência que foi integrado ao comando UCC T3 é projetado para atingir a categoria 2 da norma BS EN ISO13849­1:2008, que pode ser configurado no hardware para obter a categoria B. A avaliação de risco realizada pelo instalador do sistema na instalação deve, portanto, ter determinado qual categoria é necessária.

O UCC T3 somente deve ser colocado em funcionamento através do software Renishaw. Se isto não for observado, podem ocorrer movimentos inesperados da máquina.

RO: Recomandări de siguranţă pentru controller‐ul UCC T3

Condiţii de funcţionare

Utilizare numai la interior

Altitudine

Temperatura de funcţionare

Temperatura de depozitare

Umiditate relativă

IP30* (BS EN60529:1992) până la 2000 m

De la +5 °C la +50 °C

De la ­25 °C la +70 °C

Maxim 80% (fără condensare) pentru temperaturi până la +31 °C

Scădere liniară până la 50% la +40 °C

Tensiuni tranzitorii

Grad de poluare

Installation category II

2

NOTĂ: Pentru a ridica gradul de izolatie IP poate fi necesară închiderea controller­ului UCC T3 într­o incintă suplimentară, în funcţie de condiţiile de mediu din punctul de instalare.

NOTĂ: Pentru temperaturi sub 40 °C, puterea maxima de intrare a controlleru­lui UCC­T3 este de 800 W. Pentru temperaturi între 40

°C şi 50 °C puterea maximă este 400 W. 

ATENŢIE: Nu se recomanda utilizarea UCC T3 la temperaturi mai mari de 50 °C. 

ATENŢIE: Împământarea întregii maşini este responsibilitatea OEM sau a instalatorului. 

ATENŢIE: Izolaţie: UCC T3 se poate izola de sursele de tensiune continuă prin decuplarea conectorului de alimentare. Dacă sunt necesare nivele suplimentare de izolaţie, acestea trebuie specificate şi instalate de către producătorul sau instalatorul maşinii.

Comanda izolaţiei trebuie poziţionată la îndemâna operatorului si trebuie sa fie comformă cu IEC61010 şi cu normele naţionale aplicabile în ţara de instalare. 

ATENŢIE: Sursa de energie electrică trebuie sa permită o singură cădere (siguranţă), conform cu EN60950­1 şi trebuie să aibă

împământare. Realizares împământărilor şi protecţia la tensiuni reziduale pentru întreaga maşină este responsabilitatea OEM sau a instalatorului.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 64 of 68

UCC T3 installation guide http://www.renishaw.com

Recomandări de siguranţă

ATENŢIE: Oprirea sau izolarea controller­ului UCC T3 NU împiedică mişcările neprevăzute ale maşinii. Utilizatorului i se recomandă deconectarea maşinii de la sursa de energie electrică, sursa de aer comprimat şi alte surse de energie, în conformitate cu instrucţiunile producătorului, înainte de a pătrunde în zona periculoasă sau de a efectua orice lucrări de întreţinere. 

Dacă echipamentul este utilizat într­o manieră nespecificată de producător, protecţia oferită de echipament poate fi diminuată.

Sistemul de oprire de urgenţă integrat in UCC T3 este proiectat să se încadreze în categoria 2 a standardului BS EN ISO13849­1:2008 şi poate fi configurat hardware pentru a obţine categoria B. Evaluarea riscurilor efectuată de către instalatorul sistemului la instalare trebuie să determine ce categorie este necesară.

UCC T3 trebuie comandat numai prin intermediul software­ului Renishaw, nerespectarea acestei condiţii putând duce la miscări neprevăzute ale maşinii.

SK: Bezpečnostné odporúčania pre riadiacu jednotku UCC T3

Podmienky okolitého prostredia

Použitie v interiéri

Nadmorská výška

Prevádzková teplota

Skladovacia teplota

Relatívna vlhkosť

IP30* (BS EN60529:1992) do 2000 m

+5 °C až +50 °C

­25 °C až +70 °C

Maximálne 80% (bez kondenzácie) pre teploty do +31 °C

Lineárny pokles na 50% pri +40 °C

Prechodné napätia

Stupeň znečistenia

Installation category II

2

POZNÁMKA: Jednotku UCC T3 môže byť potrebné umiestniť do vhodnej elektrickej skrinky podľa podmienok okolitého prostredia danej inštalácie, aby sa dosiahlo vyššie krytie IP.  

POZNÁMKA: Pre okolité teploty do 40 °C je maximálny príkon jednotky UCC T3 800 W. Pre teploty od 40 °C do 50 °C je maximálny príkon 400 W. 

VÝSTRAHA: Jednotku UCC T3 sa neodporúča používať pri okolitých teplotách nad 50 °C. 

VÝSTRAHA: Uzemnenie celého prístroja je zodpovednosťou pôvodného výrobcu zariadenia (OEM) alebo firmy vykonávajúcej inštaláciu. 

VÝSTRAHA: Izolácia: Jednotka UCC T3 je izolovaná od jednosmerného napájacieho zdroja odpojením napájacieho konektora. Ak

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 65 of 68

UCC T3 installation guide http://www.renishaw.com

sa vyžadujú akékoľvek ďalšie spôsoby izolácie, musí ich špecifikovať a nainštalovať výrobca prístroja alebo firma vykonávajúca inštaláciu výrobku. Izolátor musí byť umiestnený tak, aby bol ľahko dostupný pre operátora súradnicového meracieho prístroja (CMM) a musí spĺňať normu IEC61010 a všetky príslušné národné predpisy týkajúce sa káblových rozvodov platné v krajine inštalácie. 

VÝSTRAHA: Jednotka napájacieho zdroja musí byť odolná voči jednej poruche, schválená podľa normy EN60950–1 a musí byť pripojená k napájaniu s ochranným uzemňovacím vodičom. Uzemnenie celého prístroja a jeho ochrana prúdovým chráničom je zodpovednosťou pôvodného výrobcu zariadenia (OEM) alebo firmy vykonávajúcej inštaláciu. 

Bezpečnosť prístroja

VÝSTRAHA: Vypnutie alebo izolácia jednotky UCC T3 NEMUSÍ zabrániť neočakávanému pohybu prístroja. Pred vstupom do nebezpečnej zóny alebo pred vykonaním ľubovoľných údržbových postupov sa používateľovi odporúča izolovať prístroj od zdroja elektrickej energie, stlačeného vzduchu alebo iných zdrojov energie v súlade s pokynmi výrobcu prístroja. 

Ak sa zariadenie používa spôsobom, ktorý nešpecifikoval výrobca, môže to negatívne ovplyvniť ochranu poskytovanú zariadením.

Bezpečnostný systém núdzového vypnutia, ktorý bol integrovaný do riadiacej jednotky UCC T3, je navrhnutý tak, aby spĺňal kategóriu 2 podľa normy BS EN ISO13849–1:2008. Môže byť hardvérovo nakonfigurovaný tak, aby spĺňal kategóriu B. Vyhodnotenie rizika firmou vykonávajúcou príslušnú inštaláciu systému preto musí zahŕňať určenie toho, ktorá kategória sa vyžaduje.

Jednotka UCC T3 sa smie uvádzať do prevádzky iba prostredníctvom softvéru od spoločnosti Renishaw, inak to môže spôsobiť neočakávaný pohyb prístroja.

SL: Varnostna priporočila za krmilnik UCC T3

Okoljski pogoji

Uporaba v zaprtih prostorih

Nadmorska višina

Delovna temperatura

Temperatura skladiščenja 

Relativna vlažnost 

IP30* (BS EN60529:1992) do 2000 m

+5 °C do +50 °C 

­25 °C do +70 °C 

Največ 80% (brez kondenzacije) za temperature do +31 °C

Linearno zmanjšanje do 50% pri +40 °C 

Prehodne napetosti

Prehodne napetosti

Installation category II

2

OPOMBA:  Ohišje naprave UCC T3 je morda treba spraviti v primerno električno omarico v skladu z okoljskimi pogoji inštalacije, s čimer naprava dobi višjo stopnjo zaščite IP. 

OPOMBA:  Maksimalna vhodna moč naprave UCC T3 pri temperaturah okolice pod 40 °C je 800 W. Maksimalna moč pri temperaturah med 40 °C in 50 °C je 400 W. 

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 66 of 68

UCC T3 installation guide http://www.renishaw.com

OPOZORILO:  Uporaba naprave UCC T3 ni priporočljiva pri temperaturah okolice nad 50 °C. 

OPOZORILO:  Ozemljitev celotnega stroja je odgovornost proizvajalca originalne opreme ali inštalaterja. 

OPOZORILO:  Izolacija: UCC T3 se od enosmernega električnega napajanja loči z odklopom električnega priključka. Če so potrebna dodatna sredstva za ločevanje, jih mora določiti in vgraditi proizvajalec stroja oz. tisti, ki je izdelek inštaliral. Ločilno sredstvo mora biti nameščeno v dosegu operaterja KMS in mora biti skladno s standardom IEC61010 ter z vsemi veljavnimi državnimi predpisi o električnih napeljavah v državi inštalacije. 

OPOZORILO:  Napajalnik mora biti toleranten na posamične napake, skladen z EN60950­1 in priključen na električno omrežje z vodnikom zaščitne ozemljitve. Ozemljitev in zaščita pred okvarnim tokom celotnega stroja je odgovornost proizvajalca originalne opreme ali inštalaterja. 

Varnost stroja

OPOZORILO:  Izklop ali ločitev naprave UCC T3 NE more zanesljivo preprečiti nepričakovanih gibanj stroja. Uporabniku priporočamo, naj loči stroj od virov električnega napajanja, stisnjenega zraka in drugih virov energije v skladu z navodili proizvajalca stroja, preden vstopi v nevarno območje ali se loti vzdrževalnih del. 

Drugačna uporaba opreme, kot jo je predpisal proizvajalec, lahko povzroči izpad zaščitnih funkcij opreme.

Varnostni sistem za zaustavitev v sili, ki je integriran v krmilnik UCC T3, je zasnovan za kategorijo 2 po standardu standard BS EN

ISO13849­1:2008, in ga je mogoče hardversko konfigurirati za kategorijo B. Katera kategorija je potrebna, se določi z oceno tveganj, ki jo izdela inštalater sistema za vsak primer posebej.

Krmilnik UCC T3 je dovoljeno zagnati samo s programsko opremo Renishaw, v nasprotnem primeru lahko pride do nepričakovanih gibanj stroja.

SV: Säkerhetsrekommendationer för styrenheten UCC T3

Miljöförhållanden 

Inomhusanvändning

Altitud

Driftstemperatur

Förvaringstemperatur 

Relativ fuktighet

Transientspänningar 

Utsläppsgrad 

IP30* (SS-EN60529:1992) upp till 2 000 m

+5 °C till +50 °C 

­25 °C till +70 °C 

Högst 80% (ingen kondens) för temperaturer upp till +31 °C

Linjär minskning till 50% vid +40 °C 

Installation category II

2

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 67 of 68

UCC T3 installation guide http://www.renishaw.com

OBS:  Det kan vara nödvändigt att bygga in UCC T3 i en lämplig elektrisk kapsling i enlighet med installationens miljöförhållanden, för att nå ett högre IP­värde.  

OBS:  För omgivningstemperaturer under 40 °C är den maximala ineffekten 800 W för UCC T3. Vid temperaturer mellan 40 °C och

50 °C är den maximala effekten 400 W. 

VARNING:  UCC T3 rekommenderas inte för användning i omgivningstemperaturer över 50 °C. 

VARNING:  Hela maskinen måste jordas – detta ansvar åligger återförsäljaren eller installatören. 

VARNING:  Bryta strömmen: UCC T3 avskiljs från likströmsmatningen genom att dra ur kontakten. Om andra metoder behövs för att bryta strömmen måste maskintillverkaren eller installatören specificera och montera dessa. Brytaren måste sitta så att CMM­ operatören enkelt kan komma åt den. Den ska följa IEC61010 och andra tillämpliga regler för elinstallation i det land där installationen sker.

VARNING:  Nätenheten (PSU) måste kunna stå emot enkla fel, vara godkänd enligt SS­EN60950­1 och måste vara ansluten till en matning som har skyddsjordsledare. Hela maskinen måste jordas och jordfelsbrytare installeras – detta ansvar åligger återförsäljaren eller installatören. 

Maskinsäkerhet 

VARNING:  Även om UCC T3 stängs av eller kopplas från så kan ÄNDÅ oväntade maskinrörelser uppstå. Användaren rekommenderas att bryta strömmen, tryckluften och andra energikällor till maskinen, i enlighet med maskintillverkarens anvisningar innan någon person går in i riskzonen eller utför något underhåll. 

Om utrustningen används på ett sätt som inte tillverkaren har avsett kanske skyddet fungerar sämre.

Nödstopps­/säkerhetssystemet som har integrerats i styrenheten för UCC T3 är konstruerad för att uppfylla kategori 2 enligt standarden

SS­EN ISO13849­1:2008. Detta kan konfigureras med maskinvara för att uppnå kategori B. Den riskutvärdering som systeminstallatören gjort för installationen ska därför ha fastställt vilken kategori som krävs.

UCC T3 får endast tas i drift med programvara från Renishaw – om detta inte efterföljs kan oväntade maskinrörelser inträffa.

© 2001­2012 Renishaw plc | Published from IDT Snowball on 06/09/2012

Page 68 of 68

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement