MODEL CA100 REMOTE CONTROL AUTO ALARM SYSTEM

APRIL/28/2005
MODEL CA100
REMOTE CONTROL AUTO ALARM SYSTEM
INSTALLATION & OPERATION INSTRUCTIONS
WIRING DIAGRAM
6 Pin
White
Black Antenna Wire
2 Pin
Blue
Valet Switch
6 Pin White Mini Connector
LED Indicator
2 Pin
White
Blue Wire: (-) 200mA Unlock Pulse
2 Pin
White
5 Pin
White
Green Wire: (-) 200mA Lock Pulse
Main 5 Pin White harness
MAIN 5 PIN WIRE HARNESS:
1. Red / White Wire: Parking Light Relay Power Input
2. White Wire: Parking Light Relay Output
3. Black Wire: Ground to Vehicle FRAME
4. Brown Wire: Positive output To Siren
15A Fuse
5. Red Wire: +12V To Constant Battery Source
6 PIN MINI CONNECTOR WIRE HARNESS:
12V
1. Violet Wire: Positive Door Pin Switch Input
2. Blue Wire: Instant Trigger Ground Input
3. Green Wire: Negative Door Pin Switch Input
12V
4. Pink Wire: To Ignition Switched + 12V
Cut
From ignition switch
5. Orange Wire: 200mA Grounded when armed
To start solenoid
Red wire
30
6. Tan Wire: (-) 200mA Programmable Output
85
Channel 3 / 2 Step Door Unlock.
White wire
Yellow wire
87a 86
Orange
wire
A. PROGRAMMING TRANSMITTER:
Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is
exceeded, the security system will start deleting transmitters from memory in chronological order.
1. Turn the Ignition 'switch ‘OFF/ON’ 3 TIMES and stay in ON position. Within 15 seconds.
2. Push the Valet switch 3 times and holding in on 3rd push until a long chirp is hearing then release the valet
switch. You are now in the Transmitter programming mode.
3. Press and hold any button of the transmitter until the siren responds with a confirming chirp, indicating the
signal has been stored into memory.
4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for each transmitter.
CA100
1
APRIL/28/2005
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. Three long chirps & Three parking light flashes
to confirm exit.
B. ALARM FEATURES PROGRAMMING:
ALARM FEATURE “I” PRORAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 2 times and holding in on 2nd push until one chirp with a long chirp is hearing then
release the valet switch. You are now in the Alarm feature ‘I’ programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to change.
a. The siren chirps and LED pause will indicate newly setting.
b. The system would advance to [2] LED flash, [2] chirp. (The factory default setting is always [1] LED flash,
[1] chirp.)
4 Depress the transmitter button ‘A’ again to change the feature again. Simple keep re-depressing the
transmitter button ‘A’ again until the module advances to your desired setting.
5. Depress the transmitter button ‘B’ corresponding to the feature ‘B’ you want to program.
Press
One Chirp /
Two Chirps /
Transmitter
LED one pulse
LED two pulse
Button
Factory Default Setting
Chirps on
Chirps off
1
Automatic
Rearm
On
Automatic Rearm Off
2
Instantly Door Ajar Warning.
45 seconds Delay Door Ajar error chirp.
3
+
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. Three long chirps to confirm exit.
ALARM FEATURE “II” PRORAMMING:
1
2
Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
Push the Valet switch 4 times and holding in on the 4th push until two chirps with a long chirp is hearing
then release the valet switch. You are now in the Alarm feature ‘II’ programming mode.
3 Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Three Chirps /
Two Chirps /
One Chirp /
Press
LED three pulse
LED two pulse
LED one pulse
Transmitter
Button
Factory Default Setting
0.9-second Door lock
3.0-second Door lock pulse.
Double pulse unlock
1
pulses.
Active arming
Passive arming without
Passive arming with passive
2
passive door locking
door locking.
Ignition controlled door locks Without ignition controlled
3
+
& unlocks
door locks & unlocks
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. Three long chirps to confirm exit.
ALARM FEATURE “III” PRORAMMING:
1
2
Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
Push the Valet switch 6 times and holding in on the 6th push until three chirps with a long chirp is hearing
then release the valet switch. You are now in the Alarm feature ‘III’ programming mode.
3 Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Two Chirps /
One Chirp /
Press
LED two pulse
LED one pulse
Transmitter
Button
Factory Default Setting
Shock Sensor Program Mode
1
Tan Wire = Trunk (Channel 3) Output
Gray Wire = Two Step Door Unlock Output
2
Car Jacking Off
Car Jacking On
3
+
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. Three long chirps to confirm exit.
Adjust and Test the sensitivity level of the Shock Sensor
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 6 times and holding in on the 6th push until three chirps with a long chirp is hearing
then release the valet switch. You are now in the Alarm feature ‘Shock Sensor’ programming mode.
3. Press and hold
button for 2 seconds. one long siren chirp to indicates the unit is ready to accept
adjustments of the shock sensor.
4. Press
button on the transmitter once will decrease sensitivity level by one, each time an decrease is
made the siren chirp will respond with [1] chirp, while 2 chirp indicates the minimum of sensitivity.
5. Press
button on the transmitter once will increase sensitivity level by one, each time an increase is
made the siren/horn chirp will respond with [1] chirp, while 2 chirp indicates the maximum of sensitivity.
CA100
2
APRIL/28/2005
6. Hit the bumper or strong metal part of the motorcycle to test the threshold level of the sensor.
a). Activate the warn-away (first stage the shock sensor), the siren will emit a short chirp.
b). Activate the full alarm (second stage the shock sensor), the siren will emit a long chirp.
7. When you are satisfied with the setting, press
and
buttons at the same time to lock in the
adjustment.
Note: If 20 seconds of inactivity expire, or turn on the ignition during of above steps, the unit will exit the
program mode and return to the disarmed mode. Three long chirps to confirm exit.
OPERATION MANUAL
TRANSMITTER OPERATION:
Transmitter Button
System Function
Arm & Lock door
Remark
-
Arm & Delete The Shock Sensor
Press twice within 3 seconds.
(3 seconds)
Car Locator
Panic function
Disarm & Unlock Door
Upon Armed.
Press and hold for 3 seconds
-
Disarm &Two Steps Door Unlock
Press twice within 3 seconds.
(2 seconds)
Disarm & Pop Trunk Release
Silent Arm / Disarm
Activate Car-Jacking
Press and Hold for 2 seconds
Upon Ignition off
Upon Ignition on
+
(2 seconds)
+
LED INDICATORS:
LED
Off
Slow flash
Fast flash
On (solid)
Function
Disarmed
Armed
Passive arming
Valet mode
CHIRP INDICATORS:
Chirp
1 chirp
2 chirps
3 chirps
4 chirps
6 chirps
Function
Arm
Disarm
Ajar Warning
Disarm / Intrusion
Car Locator
LED
2 flashes... pause
3 flashes... pause
4 flashes... pause
5 flashes... pause
Function
Trigger on trunk/hood
Trigger on door switch
Trigger on Dual Zone Shock Sensor
Trigger on Ignition switch
PARKING LIGHT:
Parking light
1 flash
2 flashes
3 flashes
12 flashes
Function
Arm
Disarm
Disarm / Intrusion
Car Locator
ACTIVE ARMING – LOCK & ARM:
1. Press
button on transmitter.
2. The siren will chirp once and parking light will flash once indicating that the system is now armed. The
vehicle doors will lock upon arming when interfaced with the security system.
Ajar Warning: If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar.
and
buttons at same time will arm or disarm your security
Silent Arming / Disarming: Press the
system, No chirp sound will be heard, arm / disarm confirmation will be through the vehicles parking lights only.
button twice within 3 seconds will arm the security system, by-pass the
Shock Sensor By-Pass: Press the
shock sensor. The system will chirp one additional time to confirm the sensor bypass mode was activated. The
sensor bypass feature is programmed to activate for one arming cycle only. The security system will return to
normal operation during the next arming cycle.
PASSIVE ARMING:
Active arming / disarming is controlling your security system via the remote transmitter. This security system is
equipped with an optional Passive Arming feature, which allows the security system to arm 30 seconds after
the last door is closed. Operation is as follows.
1. Turn the ignition to the “OFF” position and exit the vehicle.
2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you reopen any door /
hood / trunk, the security system LED will stop flashing. It will begin flashing again once the vehicle all
entrances are closed.
3. After 30-second timer has elapsed, the security system will automatically “ARM”. The siren will chirp [1] time
and the parking lights will flash [1] time.
PASSIVE DOOR LOCKING:
The vehicle doors will automatically lock after passive arming cycle has been completed.
ACTIVE DISARMING – UNLOCK & DISARM:
CA100
3
APRIL/28/2005
button on the transmitter.
1. Press
2. The siren will chirp twice and parking light will flash twice to indicating that the security system is now
disarmed. The vehicle doors will unlock disarming when interfaced with the security system.
Tamper Disarm: If alarm triggered, upon disarm the system, siren chirp 4 times, parking light flash 3 times.
Two Step Door Unlock: This feature will independently unlock the drives door only when disarming the
button on the transmitter a second time within 3 seconds will unlock the entire
security system. Pushing the
vehicle.
Automatic Re-Arm: If this feature is selected, the security system will automatically re-arm itself 60 seconds
after disarming with remote transmitter. Automatic rearm will cancel if any door is opened before the 60
seconds timer has elapsed.
DISARMING WITHOUT A TRANSMITTER
The Override function may be used if the remote transmitter is lost or inoperative.
1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.)
2. Within 10 seconds push and release the valet switch
The alarm will stop sounding and enter the disarm mode. You can now start and operate the vehicle normally.
VALET MODE:
The valet switch allows you to temporarily bypass all alarm function, eliminating the need to hand your
transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm function is
bypassed, however the remote panic feature and remote door locks will remain operational.
Enter Valet Mode: 1. Turn the ignition to “ON” position.
2. Push and hold valet switch for 2 seconds until the LED turns on. The LED wills
remain on as long as the system is in 'valet mode'.
Exit Valet Mode: 1. Return to normal operation, turn ignition 'ON'.
2. Push and hold valet switch for 2 seconds, The LED wills turns off indicate the
system are exiting the valet mode.
PANIC FUNCTION:
The transmitter can be used as a remote panic switch to manually trigger the alarm in case emergency.
button on the transmitter for 3 seconds. The alarm will immediately sound.
1. Press and hold
2. To stop the alarming press and hold
button on the transmitter for 3 seconds.
3. If the button is not pressed, the alarm will automatically stop after 30 seconds.
TRIGGER THE SYSTEM
When armed, your vehicle is protected as follows:
1. Light impacts will trigger the warn-away signal. A long chirp from siren/horn.
2. Heavy impacts / Doors open / Hood open / Trunk open / Turns on the ignition switch will trigger the
programmed sequence.
The starter disable relay (if installed) prevents the vehicle’s starter from cranking. The siren and parking lights
will turn on to alerting of an intrusion for 30 seconds. Then it will stop and automatic reset and re-arm. If the one
of sensors or detectors still active, the alarm system will sound a maximum of 6 times of 30 seconds cycles.
ANTI CAR - JACKING
Warning: If you don't need the car jacking function in this alarm system, be sure to set car jacking feature “OFF”. This
system is default setting car jacking “OFF”.
Active Anti Car Jacking:
and
buttons at the same time for 2 seconds. The parking
1. Upon ignition is “On”, press and hold the transmitter
lights will turns on for 1.5 seconds to indicate the system enters the car-jacking mode.
2. Once the system in car-jacking mode, If you are forced from the vehicle, the system will be trigger when the door is
opened and closed while the ignition is “ON”.
Trigger The Car Jack Mode:
a). 50 seconds after the system has been triggered. The siren will start chirping for 15 seconds.
b). During this 15 seconds period of chirping, you will be alerting to push the valet switch once to turn off the car-jacking
feature. If not, it will enter second timer car jacking.
c). 65 seconds after the system has beer triggered. The siren starts alarming and the parking light starts flashing.
d). 90 seconds after the system has beer triggered
1. The siren still alarming and the parking light flashing, and
2. The starter disable will activate to prevent the vehicle from starting.
3. It will remain active until the vehicle's battery power exhausted.
Override The System To Turn Off Car Jacking: Turn the ignition switch from OFF to ON, and within 10 seconds push
valet switch, the siren will stop and the system disarmed
CAR LOCATOR:
Upon armed, press
button on the transmitter to active car locator function. The siren will chirp 6 times. The parking light
will flash 12 times, for you to easily locate your car.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions.
CA100
4
APRIL/28/2005
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
CA100
5