Chauvet Home Safety Product User manual

User Manual
Edition Notes
Edition Notes
The Q-Spot™ 560-LED User Manual Rev. 08 covers the description, safety
precautions, installation, programming, operation, and maintenance of the Q-Spot™
560-LED. CHAUVET® released this edition of the Q-Spot™ 560-LED User Manual
in January 2013.
Trademarks
CHAUVET® is a registered trademark of CHAUVET & Sons Inc. (d/b/a CHAUVET®
or Chauvet). The CHAUVET® logo in its entirety including the CHAUVET name and
the dotted triangle, and all other trademarks on this manual pertaining to services,
products, or marketing statements (example: It’s Green Thinking™) are owned or
licensed by CHAUVET®. Any other product names, logos, brands, company names,
and other trademarks featured or referred to within this document are the property of
their respective trademark holders.
Copyright Notice
Manual Usage
CHAUVET® owns the content of this user manual in its entirety, including but not
limited to pictures, logos, trademarks, and resources.
© Copyright 2013 CHAUVET®. All rights reserved.
Electronically published by CHAUVET® in the United States of America.
CHAUVET® authorizes its customers to download and print this manual for
professional information purposes only. CHAUVET® expressly prohibits the usage,
copy, storage, distribution, modification, or printing of this manual or its content for
any other purpose without its written consent.
Document Printing
For better results, print this document in color, on letter size paper (8.5 x 11 inches),
double sided. If using A4 paper (210 x 297 mm), configure your printer to scale the
content accordingly.
Intended Audience
Any person in charge of installing, operating, and/or maintaining this product should
read the guide that shipped with it as well as this manual in their entirety before
installing, operating, or maintaining this product.
Disclaimer
Document Revision
CHAUVET® believes that the information contained in this manual is accurate in all
respects. However, CHAUVET® assumes no responsibility for any error or
omissions in this document. CHAUVET® reserves the right to revise this document
and to make changes from time to time in the content hereof without obligation of
CHAUVET® to notify any person or company of such revision or changes. This
does not constitute in any way a commitment by CHAUVET® to make such
changes. CHAUVET® may issue a revision of this manual or a new edition of it to
incorporate such changes.
The Q-Spot™ 560-LED User Manual Rev. 08 supersedes all previous versions of
this manual. Please discard any older versions of this manual you may have,
whether in printed or electronic format, and replace them with this version.
Author
Date
Editor
Date
D. Couppe
1/10/13
S. Diaz
1/10/13
Q-Spot™ 560-LED User Manual Rev. 08
Table of Contents
Table of Contents
1. Before You Begin ............................................................................................... 1
What Is Included ................................................................................................................. 1
Unpacking Instructions ........................................................................................................ 1
Claims ......................................................................................................................................... 1
Typographic Conventions ................................................................................................... 1
Icon Meaning....................................................................................................................... 2
Product at a Glance ............................................................................................................ 2
Safety Notes ........................................................................................................................ 3
Personal Safety ........................................................................................................................... 3
Mounting and Rigging.................................................................................................................. 3
Power and Wiring ........................................................................................................................ 3
Operation ..................................................................................................................................... 3
Expected LED Lifespan ...................................................................................................... 3
2. Introduction ........................................................................................................ 4
Product Description ............................................................................................................. 4
Features .............................................................................................................................. 4
Additional Features...................................................................................................................... 4
Product Overview ................................................................................................................ 5
Product Dimensions ............................................................................................................ 7
3. Setup ................................................................................................................... 8
AC Power ............................................................................................................................ 8
AC Plug ....................................................................................................................................... 8
Fuse Replacement ...................................................................................................................... 8
DMX Linking ........................................................................................................................ 9
DMX Modes ................................................................................................................................. 9
Master/Slave Connectivity ........................................................................................................... 9
Gobo Replacement ........................................................................................................... 10
Mounting ........................................................................................................................... 11
Orientation ................................................................................................................................. 11
Rigging ...................................................................................................................................... 11
Product Mounting Diagram ........................................................................................................ 11
4. Operation .......................................................................................................... 12
Control Panel Description ................................................................................................. 12
Control Options ................................................................................................................. 12
Programming..................................................................................................................... 12
DMX Operation .......................................................................................................................... 12
Stand-alone Operation .............................................................................................................. 13
Master/Slave.............................................................................................................................. 13
Display Mode ............................................................................................................................. 13
Software Version ....................................................................................................................... 13
Keylock ...................................................................................................................................... 14
Reset ......................................................................................................................................... 14
Dimmer Curve ........................................................................................................................... 14
Fader Reversal .......................................................................................................................... 15
Range Limitation........................................................................................................................ 15
Reset Control............................................................................................................................. 15
Move-in Black ............................................................................................................................ 15
Loss of DMX Settings ................................................................................................................ 15
Fan Wait .................................................................................................................................... 16
System Default .......................................................................................................................... 16
Edit Custom ............................................................................................................................... 16
Menu Map ......................................................................................................................... 17
DMX Values ...................................................................................................................... 19
Q-Spot™ 560-LED User Manual Rev. 08
-i-
Table of Contents
5. Technical Information ...................................................................................... 24
Product Maintenance ........................................................................................................ 24
Troubleshooting Guide ...................................................................................................... 25
Returns Procedure ............................................................................................................ 26
Contact Us ........................................................................................................................ 26
Technical Specifications ................................................................................................... 27
-ii-
Q-Spot™ 560-LED User Manual Rev. 08
Before You Begin
1. Before You Begin
What Is
Included
· One Q-Spot™ 560-LED
· One IEC Power Cord with Edison Plug (US Market)
· Two Omega Brackets
· One Safety Cable
· Warranty Card
· Quick Reference Guide
Unpacking
Instructions
Claims
Immediately upon receiving this product, carefully unpack and check the container. Make
sure you have received all the parts indicated above and all the parts are in good condition.
If the container or the material inside the container (the product and included accessories)
appear damaged from shipping, or show signs of mishandling, upon receipt notify the
carrier immediately, not CHAUVET®,. Failure to do so in a timely manner may invalidate
your claim with the carrier. In addition, keep the container and all the packing material for
inspection.
For other issues such as missing components or parts, damage not related to shipping, or
concealed damage, file a claim with CHAUVET® within seven (7) days of receiving the
merchandise.
Typographic
Conventions
Convention
1~512
50/60
Claims
<SET>
Settings
MENU > Settings
1~10
Yes/No
ON
Q-Spot™ 560-LED User Manual Rev. 08
Meaning
A range of values in the text
A set of mutually exclusive values in the text
A new term, another document reference, or section or chapter in
this document
A button on the product’s control panel
A product function or a menu option
A sequence of menu options
A range of menu values from which to choose in a menu
A set of two mutually exclusive menu options in a menu
A unique value to be entered or selected in a menu
-1-
Before You Begin
Icon Meaning
Icon
Meaning
This icon indicates critical installation, configuration, or operation
information. Failure to comply with this information may render the
product partially or completely inoperative, damage third-party
equipment, or cause harm to you.
This icon indicates important installation or configuration
information. Failure to comply with this information may prevent
the product from functioning correctly.
This icon indicates useful, although non-critical information.
The term “DMX” used throughout this document refers to the USITT DMX512-A
transmission protocol.
Product at a
Glance
Use on Dimmer
Outdoor Use
Sound Activated
DMX
Master/Slave
-2-
x
x
P
P
P
Auto Programs
Auto-ranging Power Supply
Replaceable Fuse
User Serviceable
Duty Cycle
P
P
P
x
x
Q-Spot™ 560-LED User Manual Rev. 08
Before You Begin
Safety Notes
Read all these Safety Notes before starting to work with this product. These notes include
important safety information about the installation, usage, and maintenance of this
product.
There are no user serviceable parts in this product. Any reference to servicing you
find in this User Manual only applies to properly CHAUVET® certified technicians.
Do not open the housing or attempt any repairs unless you are one of them.
Please refer to all applicable local codes and regulations for the proper installation
of this product.
Personal Safety
Mounting and
Rigging
Power and Wiring
Operation
·
·
·
·
Avoid direct eye exposure to the light source while the product is on.
Always disconnect this product from its power source before servicing.
Always connect this product to a grounded circuit to avoid the risk of electrocution.
Do not touch this product’s housing when operating because it may be very hot.
· This product is for indoor use only! To prevent risk of fire or shock, do not expose this
product to rain or moisture.
· Make sure there are no flammable materials close to this product while operating.
· When hanging this product, always secure it to a fastening device using a safety
chain/cable (included).
· Do not carry this product from the head. Always use the handles.
· Always make sure that you are connecting this product to the proper voltage, as per
the specifications in this manual or on the product’s sticker.
· Never connect this product to a dimmer pack or rheostat.
· Never disconnect this product by pulling or tugging on the power cable.
· Do not operate this product if you see damage on the housing, lenses, or cables. In
any of these cases, have the damaged parts replaced by an authorized technician at
once.
· Do not cover the ventilation slots when this product is operating to avoid internal
overheating.
· Do not aim this product toward the Sun. The lenses could concentrate the solar energy
and cause internal overheating.
· The maximum ambient temperature is 104° F (40° C). Do not operate this product at a
higher temperature.
· In case of a serious operating problem, stop using this product immediately!
In the unlikely event that your CHAUVET® product may require service, contact
CHAUVET® Technical Support.
Expected LED
Lifespan
LEDs gradually decline in brightness over time, mostly because of heat. Packaged in
clusters, LEDs exhibit higher operating temperatures than in ideal, single LED conditions.
For this reason, using clustered LEDs at their fullest intensity significantly reduces the
LEDs’ lifespan. Under normal conditions, this lifespan can be of 40,000 to 50,000 hours. If
extending this lifespan is vital, lower the operational temperature by improving the
product’s ventilation and reducing the external temperature. In addition, limiting the overall
projection intensity may also help to extend the LEDs’ lifespan.
Q-Spot™ 560-LED User Manual Rev. 08
-3-
Introduction
2. Introduction
Product
Description
Features
Additional Features
-4-
The Q-Spot™ 560-LED is a high-power moving yoke product equipped with three (3) 60watt white LEDs. This product includes a color wheel with seven slots, plus white, and two
gobo wheels. One gobo wheel has seven fixed gobos, plus open. The other gobo wheel
has six rotating slot-n-lock gobos, plus open. In addition, the Q-Spot™ 560-LED includes
remote focus and a rotating 3-facet prism.
· 13 or 17-channel DMX-512 LED moving yoke
· Pan: 540° / tilt: 270°
· Color wheel:
7 colors + white
Split colors
Rainbow color spin at variable speeds
· Gobo wheel 1:
Gobo shake
7 gobos + open
Gobo wheel spin at variable speeds
· Gobo wheel 2:
Indexed, rotating gobo wheel with gobo shake
6 slot-n-lock gobos + open
2 glass, 4 metal
Rotating gobo wheel spin at variable speeds
· Extremely bright with 19 degree beam angle for big looks
· 3-facet, high-speed rotating prism at variable speeds
· Variable focus
· Variable iris
· Variable electronic shutter (for strobing)
· Remote fixture reset and vector speed channel
· 255 user-programmable steps without DMX controller
· Move-in-black for pan/tilt
· Built-in automated programs
· Built-in sound activated programs
· 3 high-powered, 60 W (14 A) LEDs
· User-selectable pan/tilt ranges
· Automatic pan and tilt correction
· Quiet operation
· 3-pin and 5-pin DMX connections
Q-Spot™ 560-LED User Manual Rev. 08
Introduction
Product Overview
DMX In
Power Switch
Rear View
DMX Out
Control Panel
Front View
Q-Spot™ 560-LED User Manual Rev. 08
-5-
Introduction
Color Wheel
Gobo Wheel 1
-6-
Gobo Wheel 2
Q-Spot™ 560-LED User Manual Rev. 08
Introduction
Product Dimensions
Q-Spot™ 560-LED User Manual Rev. 08
-7-
Setup
3. Setup
AC Power
The Q-Spot™ 560-LED has an auto-ranging power supply that works with an input voltage
range of 100~240 VAC, 50/60 Hz.
Make sure that you are connecting this product to the proper voltage, as per the
specifications in this manual or on the product’s sticker.
Always connect this product to a protected circuit with an appropriate electrical
ground to avoid the risk of electrocution or fire.
To determine the power requirements for the Q-Spot™ 560-LED, refer to the label affixed
to the side of the product. You can also refer to the Technical Specifications chart in the
Technical Information chapter of this manual.
The listed current rating indicates the maximum current draw during normal operation. For
more information, you may download the document Sizing the Circuit Breakers from the
CHAUVET® website: www.chauvetpro.com.
Never connect this product to a rheostat (variable resistor) or dimmer circuit, even if
the rheostat or dimmer channel serves only as a 0 to 100% switch.
AC Plug
Fuse Replacement
The Q-Spot™ 560-LED comes with a power input cord terminated with a IEC connector on
one end and an Edison plug on the other end (US market). If the power input cord that
came with your product has no plug or you need to change the Edison plug, use the table
below to wire the new plug.
Connection
Wire (US)
Wire (Europe)
Screw Color
AC Live
Black
Brown
Yellow or Brass
AC Neutral
White
Blue
Silver
AC Ground
Green/Yellow
Green/Yellow
Green
This product uses a T5 A, 250 V fuse.
Make sure to disconnect the product’s power cord before replacing a blown fuse,
and always replace with a fuse of the same type and rating.
1.
2.
3.
4.
Disconnect the product from the power outlet.
Wedge the tip of a flat head screwdriver into the slot of the fuse holder.
Pry the safety cap out of the housing to pull out the installed fuse.
Remove the blown fuse from the safety cap and replace with a fuse of the exact same
type and rating (T5 A, 250 V).
5. Insert the fuse holder back in place and reconnect power.
Installed fuse
(held by plastic clip)
Safety cap
Spare fuse
(inside safety cap)
-8-
Q-Spot™ 560-LED User Manual Rev. 08
Setup
DMX Linking
DMX Modes
Master/Slave
Connectivity
You may link the Q-Spot™ 560-LED to a DMX controller using a standard DMX serial
connection. If using other DMX compatible products with the Q-Spot™ 560-LED, you can
control each product individually with a single DMX controller.
The Q-Spot™ 560-LED uses the standard DMX data connection for its DMX personalities,
Basic and Advanced. You will find information about these DMX modes in this manual.
Refer to the Introduction chapter for a brief description, the Operation chapter for
configuration details, and the DMX Values section for individual channel values.
The Master/Slave mode enables a Q-Spot™ 560-LED (the “master unit”) to control one or
more Q-Spot™ 560-LED’s (the “slave units”) without a DMX controller. A Q-Spot™ 560-LED
becomes the master unit when running an AUTO, SOUND, TEST, or CUSTOM program.
You must configure the slave units to operate in SLAVE mode from their respective control
panels. During the master/slave operation, the slave units will operate in unison with the
master unit.
If you are not familiar with the DMX standard, master/slave connectivity, or if you need
information about the DMX cables needed to link this product to a DMX controller, you may
download the document DMX Primer from the CHAUVET® website: www.chauvetpro.com.
DO NOT connect a DMX controller to the products operating in Master/Slave mode.
The DMX controller signals may interfere with the signals from the master unit.
The Operation chapter of this manual provides detailed instructions on how to
configure the Master and Slave units.
Q-Spot™ 560-LED User Manual Rev. 08
-9-
Setup
Gobo
Replacement
1. Turn the product off and disconnect from the power outlet.
2. Open the head cover by loosening the four fastening screws at the sides of the
top cover.
3. Separate the gobo plate from the gobo wheel by pushing the gobo plate toward
the front of the moving head (direction 1 in the diagram). Be careful not to push
the gobo out of the gobo plate.
4. Take out the gobo plate by pulling the gobo plate outward (direction 2 in the
diagram).
5. On a flat surface, remove the expansion ring that holds the gobo in place.
6. Remove the gobo from the gobo plate.
7. Insert a new gobo and hold in place with the expansion ring.
8. Slide the tip of the gobo plate under the pressure plate near the center of the
gobo wheel.
9. Push the gobo plate inward. DO NOT force the gobo plate into the gobo wheel
slot.
Note: If correctly installed, the gobo plate should easily snap into the gobo
wheel slot.
Gobo Plate #1 contains a magnet used by the product for positioning
purposes. When replacing gobos, be sure to return gobo plate #1 to position
#1 on the wheel.
-10-
Q-Spot™ 560-LED User Manual Rev. 08
Setup
Mounting
Before mounting this product, read and follow the Safety Notes in the Before You Begin
chapter of this manual.
Orientation
Always mount this product in any safe position while making sure that there is adequate
room for ventilation, configuration, and maintenance.
Rigging
CHAUVET® recommends following the general guidelines below when mounting this
product.
· When selecting an installation location, consider easy access to this product for
operation, programming adjustments, and routine maintenance.
· Make sure to mount this product away from any flammable material as indicated in the
Safety Notes section.
· Never mount the product in places where rain, high humidity, extreme temperature
changes, or restricted ventilation may affect it.
· If hanging this product, make sure that the mounting location can support the product’s
weight. Please see the Technical Specifications section of this manual for the weight
requirement of this product.
Procedure
The Q-Spot™ 560-LED comes with two (2) omega brackets to which you can attach
clamps. You must supply your own clamps. Make sure the clamps are capable of
supporting the weight of this product. You must use two mounting points per unit.
Safety Cable
Omega Brackets
Product Mounting
Diagram
Floor Mounting
Q-Spot™ 560-LED User Manual Rev. 08
Overhead Mounting
-11-
Operation
4. Operation
Control Panel
Description
Button
Function
<MENU>
Exits from the current menu or function
<ENTER>
Enables the currently displayed menu or sets the currently selected
value in to the current function
<UP>
Navigates upward through the menu list and increases the numeric
value when in a function
<DOWN>
Navigates downward through the menu list and decreases the numeric
value when in a function
Control Options
You can set the Q-Spot™ 560-LED start address in the 001~512 DMX range. This enables
control of up to 30 units in the 17-channel ADVANCED personality.
Programming
Refer to the Menu Map to learn about the menu options. The Menu Map has a Menu Level
and a variety of programming levels for each option.
·
To go to an option in the Menu Level, press <MENU> repeatedly until the option shows
on the display. Press <ENTER> to select. This will take you to the first programming
level for that option.
·
To select an option or value within the current programming level, press <UP> or
<DOWN> until the option shows on the display. Press <ENTER> to select. In this
case, if there is another programming level, you will see that first option or you will see
the selected value.
·
To exit to the previous menu level, press <MENU>.
In the EDIT menu, <UP> and <DOWN> will only change the value of the current
option. To change to the next option, press <ENTER>.
DMX Operation
1. Select DMX operation.
a) Go to MENU > INTRO > RUN.
b) Select DMX 512.
2. Select a DMX mode.
a) Go to MENU > INTRO > PERSON.
b) Select BASIC or ADVANCED.
3. Select the starting address.
a) Go to MENU > INTRO > ADDRESS.
b) Select a starting address, 001~496 (Advanced) or 001~500 (Basic).
The highest possible starting address for each DMX mode is as follows:
DMX Mode
Basic
Advanced
-12-
DMX Address
500
496
Q-Spot™ 560-LED User Manual Rev. 08
Operation
Stand-alone
Operation
1. Go to MENU > INTRO > RUN.
2. Select a stand-alone operation mode (AUTO 1, AUTO 2, CUSTOM,
SOUND 1, SOUND 2, or TEST).
Of all the stand-alone operation modes indicated above, only “CUSTOM” is editable
(see Edit Custom).
Master/Slave
The Master/Slave mode enables one or more Q-Spot™ 560-LED products (the slaves) to
simultaneously duplicate the output of another Q-Spot™ 560-LED (the master), without a
DMX controller, whether in auto/custom or static modes,.
1. Set the master unit:
a) Select a stand-alone mode, as indicated above.
2. Set each of the slave units:
a) Go to MENU > INTRO > RUN.
b) Select SLAVE.
· Do not connect a DMX controller to the master or slave products.
· The master unit should be the first unit in the DMX daisy chain.
Display Mode
1. Go to MENU > INTRO > DISPLAY.
2. Select a display mode (60 CLOSE or BRIGHT).
· When in the “60 CLOSE” setting, the LCD’s backlight will turn off after 60 s.
· When in the “BRIGHT” setting, the LCD’s backlight will stay on.
Software Version
1. Go to MENU > INTRO > INFO.
2. The display will show Edition.
3. Press <ENTER> to see the installed software version.
Q-Spot™ 560-LED User Manual Rev. 08
-13-
Operation
Keylock
Locks or unlocks the product’s display.
1. Go to MENU > INTRO > KEYLOCK.
2. Select YES or NO.
When Keylock is in the “YES” setting, you will have to enter the password after 30
seconds of control panel inactivity or each time you turn the product on.
The default (non-modifiable) password is
<UP>, <DOWN>, <UP>, <DOWN>, and <ENTER>.
Reset
Dimmer Curve
Reset all custom settings to their default values.
1. Go to MENU > INTRO > RESET.
2. Select YES or NO.
This option defines the output speed when you modify the values of the dimmer faders.
This setting provides you with four different options to simulate the dimming curve of an
incandescent lighting product.
1. Go to MENU > INTRO > DIMMER.
2. Select DIMMER 0~4.
DIMMER 0:
DIMMER 1~4:
-14-
The output is proportional (linear) to the dimmer channel.
The output follows the dimmer channel values based on the
corresponding dimmer curve, being DIM1 the fastest and DIM4 the
slowest.
Q-Spot™ 560-LED User Manual Rev. 08
Operation
Fader Reversal
Define how the pan, tilt, and dimmer increase.
1. Go to MENU > INVERT > PAN.
2. Select a fader direction (NORMAL or REVERSE).
3. Go to MENU > INVERT > TILT.
4. Select a fader direction (NORMAL or REVERSE).
5. Go to MENU > INVERT > DIMMER.
6. Select a fader direction (NORMAL or REVERSE).
7. Go to MENU > INVERT > USE.
8. Select YES to activate the new settings or NO to stop using them.
· When in NORMAL, the pan, tilt, and dimmer values will increase as the position
of the respective fader increases.
· When in REVERSE, the pan, tilt, and dimmer values will decrease as the position
of the respective fader increases.
Range Limitation
Reset Control
Limit the pan or tilt range.
1. Go to MENU > RANGE > P/START.
2. Select the starting point for the limited pan (000~255).
3. Go to MENU > RANGE > P/FINISH.
4. Select the finishing point for the limited pan (000~255).
5. Go to MENU > RANGE > T/START.
6. Select the starting point for the limited tilt (000~255).
7. Go to MENU > RANGE > T/FINISH.
8. Select the finishing point for the limited tilt (000~255).
9. Go to MENU > RANGE > USE.
10. Select YES to activate the new settings or NO to stop using them.
Select how you reset the product, either using the DMX controller or from the control
panel.
1. Go to MENU > SPECIAL > RESET.
2. Select DMX or SYSTEM.
DMX: Enables the DMX controller to reset the product (Control function).
SYSTEM:
Restricts the reset function to the control panel.
Move-in Black
Activate or deactivate the move-in black 3-second delay.
1. Go to MENU > SPECIAL > BLACKD.
2. Select YES to enable the 3 seconds delay or NO to make the blackout immediate.
Loss of DMX
Settings
Define response to a DMX failure.
1. Go to MENU > SPECIAL > DMXERROR.
2. Select SAVE to show the last look when DMX is lost or BLAK to make the product
blackout immediately.
Q-Spot™ 560-LED User Manual Rev. 08
-15-
Operation
Fan Wait
System Default
Edit Custom
Stop the fan during a blackout.
1. Go to MENU > SPECIAL > FAN_WAIT.
2. Select ON or OFF.
Default all product parameters to their default values.
1. Go to MENU > EXTRA.
2. Press <ENTER> (PASSWORD) will show on the display.
3. Press <ENTER> (**** will show on the display).
4. Enter the password, as explained in Keylock.
5. Use <UP> to select DEFAULT.
6. Press <ENTER> (NO will show on the display).
7. Select YES and press <ENTER> to default the product or press <MENU> to exit.
Program up to 255 steps in a single custom program.
1. Go to MENU > EDIT.
2. Press <ENTER> to go to STEP.
3. Press <ENTER> to select a value. The current value (001~255) will show on the LCD.
4. Press <UP> or <DOWN> to select a new value.
5. Press <ENTER> to accept the value.
6. Press <ENTER> to go to PAN.
7. Repeat steps “1” through “6” for TILT, SPEED, COLOR, GOBO1, GOBO2,
GOBO2ROT, PRISM, PRISMT, IRIS, FOCUS, DIMMER, STROBE, and TIME.
8. Press <ENTER> to go to USE.
9. Select YES to save the settings for this step or NO to delete them.
10. Repeat steps “3” to “8” for the other steps.
The product will execute all the steps in the CUSTOM program and stop.
To make the product start over, add a last step whose duration is 0 seconds.
Example:
Step 1:
Step 2:
Step 3:
Step 4:
Step 5:
Time = 5
Time = 4
Time = 6
Time = 0
Time = 0
Use = Yes
Use = Yes
Use = Yes
Use = Yes
Use = No
(This step creates a loop)
(Unused steps)
Step 255
-16-
Time = 0
Use = No
Q-Spot™ 560-LED User Manual Rev. 08
Operation
Menu Map
Main Level
INTRO
Programming Levels
ADDRESS
RESET
RUN
PERSON
DISPLAY
KEYLOCK
DIMMER
INFO
INVERT
PAN
TILT
DIMMER
USE
RANGE
P/START
P/FINISH
T/START
T/FINISH
USE
SPECIAL
BLACKD
RESET
FAN_WAIT
DMXERROR
Description
001~512
YES
NO
DMX512
AUTO 1
AUTO 2
SOUND 1
SOUND 2
CUSTOM
TEST
SLAVE
BASIC
ADVANCED
60 CLOSE
BRIGHT
YES
NO
DIMMER 0
DIMMER 1
DIMMER 2
DIMMER 3
DIMMER 4
VERSION
EDITION
NUMBER
NORMAL
REVERSE
NORMAL
REVERSE
NORMAL
REVERSE
YES
NO
000~255
YES
NO
YES
NO
DMX
SYSTEM
ON
OFF
SAVE
BLAK
Selects a starting DMX address
Resets the product’s custom settings
Selects DMX512-A running mode
Selects the first automatic program
Selects the second automatic program
Selects the first sound activated program
Selects the second sound program
Selects the user customizable program
Selects the fixture’s test sequence
Selects the Slave running mode
Selects the 13-channel DMX mode
Selects the 17-channel DMX mode
Turns off the display after 60 s
Keeps the display on
Activates the control panel password
Linear dimmer
Slow (DIM 4) to fast (DIM1) dimmer curves
Shows the version of the installed S/W
Defines the direction of the pan function
Defines the direction of the tilt function
Defines the direction of the dimmer function
Activates the changes
Sets the pan start point (restricted range)
Sets the pan end point (restricted range)
Sets the tilt start point (restricted range)
Sets the tilt end point (restricted range)
Activates the changes
Activates the move-in black delay (3 s)
The DMX controller can reset the product
The control panel can reset the product
Forces the fan to stop during a blackout
Save the last look when DMX is lost
Goes to black when DMX is lost
Continued on next page
Q-Spot™ 560-LED User Manual Rev. 08
-17-
Operation
Main Level
EDIT
Programming Levels
STEP
PAN
TILT
SPEED
COLOR
GOBO1
GOBO2
GOBO2ROT
PRISM
PRISMT
IRIS
FOCUS
DIMMER
STROBE
TIME
USE
Extra
Default
-18-
Password
Default
000~255
YES
NO
****
YES
NO
Description
Selects the program step
Selects the pan position
Selects the tilt position
Selects the pan/tilt speed
Selects the color wheel position
Selects the fixed gobo wheel position
Selects the rotating gobo wheel position
Selects the gobo rotation mode
Selects the prism rotation mode
Selects the prism rotation fine adjustment
Selects the iris position
Selects the focus position
Selects the dimmer value
Selects the strobe frequency and mode
Selects the step duration
Activates the changes
Opens the Default menu level
Sets unit back to default factory settings
Q-Spot™ 560-LED User Manual Rev. 08
Operation
DMX Values
Basic
Channel
Function
1
2
Pan
Tilt
3
Color wheel
4
Gobo Wheel 1
5
Gobo Wheel 2
6
Gobo Wheel 2
Rotation
Value
000 ó 255
000 ó 255
000 ó 009
010 ó 019
020 ó 029
030 ó 039
040 ó 049
050 ó 059
060 ó 069
070 ó 079
080 ó 099
100 ó 119
120 ó 139
140 ó 159
160 ó 179
180 ó 199
200 ó 219
220 ó 255
000 ó 010
011 ó 020
021 ó 030
031 ó 040
041 ó 050
051 ó 060
061 ó 070
071 ó 080
081 ó 095
096 ó 110
111 ó 125
126 ó 140
141 ó 155
156 ó 170
171 ó 185
186 ó 255
000 ó 010
011 ó 020
021 ó 030
031 ó 040
041 ó 050
051 ó 060
061 ó 070
071 ó 085
086 ó 100
101 ó 115
116 ó 130
131 ó 145
146 ó 160
161 ó 255
000 ó 060
061 ó 150
151 ó 165
166 ó 255
Percent/Setting
0~540°
0~270°
No Function
Red
Green
Yellow
Blue
Orange
Magenta
Light Blue
Light Blue/Magenta
Magenta/Orange
Orange/Blue
Blue/Yellow
Yellow/Green
Green/Red
Red/Open
Rainbow or Linear Effect
No gobo
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Shaking gobo 7
Shaking gobo 6
Shaking gobo 5
Shaking gobo 4
Shaking gobo 3
Shaking gobo 2
Shaking gobo 1
Flow effect
No gobo
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Shaking gobo 6
Shaking gobo 5
Shaking gobo 4
Shaking gobo 3
Shaking gobo 2
Shaking gobo 1
Flow effect
360° Indexing
Clockwise Rotation ~ Slow to Fast
No Function
Counter-Clockwise Rotation ~ Slow to Fast
Continues on the next page
Q-Spot™ 560-LED User Manual Rev. 08
-19-
Operation
Basic
(Cont.)
Channel
Function
7
Prism
8
Prism Rotation
9
Iris
10
11
Focus
Dimmer
12
Strobe
Value
000 ó 009
010 ó 039
040 ó 049
050 ó 059
060 ó 069
070 ó 079
080 ó 089
090 ó 099
100 ó 109
110 ó 119
120 ó 129
130 ó 139
140 ó 149
150 ó 159
160 ó 169
170 ó 179
180 ó 189
190 ó 199
200 ó 209
210 ó 219
220 ó 229
230 ó 239
240 ó 255
000 ó 009
010 ó 119
120 ó 129
130 ó 255
000 ó 199
200 ó 209
210 ó 219
220 ó 229
230 ó 239
240 ó 255
000 ó 255
000 ó 255
000 ó 031
032 ó 063
064 ó 095
096 ó 127
128 ó 159
160 ó 191
192 ó 223
224 ó 255
Percent/Setting
No Function
Prism
Effect1
Effect2
Effect3
Effect4
Effect5
Effect6
Effect7
Effect8
Effect9
Effect10
Effect11
Effect12
Effect13
Effect14
Effect15
Effect16
Effect17
Effect18
Effect19
Effect20
Prism
No Function
Clockwise rotate ~ slow to fast
No Function
Counter-clockwise rotation ~ slow to fast
Linear Iris
Iris Effect1
Iris Effect2
Iris Effect3
Iris Effect4
Random
0~100%
0~100%
Close
Open
Strobe 0~20Hz
Open
Pulse Effect
Open
Random Effect
Open
Continues on the next page
-20-
Q-Spot™ 560-LED User Manual Rev. 08
Operation
Basic
(Cont.)
Channel
13
Advanced
Channel
Function
Value
000 ó 019
020 ó 039
040 ó 059
060 ó 139
140 ó 149
150 ó 159
160 ó 169
170 ó 179
180 ó 189
190 ó 199
200 ó 219
220 ó 235
236 ó 239
240 ó 243
244 ó 247
248 ó 251
252 ó 255
Control
Function
1
2
3
4
5
Pan
Pan Fine
Tilt
Tilt Fine
Pan/Tilt Speed
6
Color wheel
7
Gobo Wheel 1
Value
000 ó 255
000 ó 255
000 ó 255
000 ó 255
000 ó 255
000 ó 009
010 ó 019
020 ó 029
030 ó 039
040 ó 049
050 ó 059
060 ó 069
070 ó 079
080 ó 099
100 ó 119
120 ó 139
140 ó 159
160 ó 179
180 ó 199
200 ó 219
220 ó 255
000 ó 010
011 ó 020
021 ó 030
031 ó 040
041 ó 050
051 ó 060
061 ó 070
071 ó 080
081 ó 095
096 ó 110
111 ó 125
126 ó 140
141 ó 155
156 ó 170
171 ó 185
186 ó 255
Percent/Setting
Dim setting as set in product
Pan/tilt black activation
Pan/tilt black deactivation
No Function
Auto program 1 (3 s activation delay)
Auto program 2 (3 s activation delay)
Test (3 s activation delay)
Custom program (3 s activation delay)
Sound1
Sound2
Reset (3 s activation delay)
No Function
DIM0 (3 s activation delay)
DIM1 (3 s activation delay)
DIM2 (3 s activation delay)
DIM3 (3 s activation delay)
DIM4 (3 s activation delay)
Percent/Setting
0~540°
Fine movement control
0~270°
Fine movement control
Fast~Slow
No Function
Red
Green
Yellow
Blue
Orange
Magenta
Light Blue
Light Blue/Magenta
Magenta/Orange
Orange/Blue
Blue/Yellow
Yellow/Green
Green/Red
Red/Open
Rainbow or Linear Effect
No gobo
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Shaking gobo 7
Shaking gobo 6
Shaking gobo 5
Shaking gobo 4
Shaking gobo 3
Shaking gobo 2
Shaking gobo 1
Flow effect
Continues on the next page
Q-Spot™ 560-LED User Manual Rev. 08
-21-
Operation
Advanced
(Cont.)
Channel
Function
8
Gobo Wheel 2
9
Gobo Wheel 2
Rotation
10
Prism
11
Prism Rotation
12
Iris
13
14
15
Focus
Focus Fine
Dimmer
Value
000 ó 010
011 ó 020
021 ó 030
031 ó 040
041 ó 050
051 ó 060
061 ó 070
071 ó 085
086 ó 100
101 ó 115
116 ó 130
131 ó 145
146 ó 160
161 ó 255
000 ó 060
061 ó 150
151 ó 165
166 ó 255
000 ó 009
010 ó 039
040 ó 049
050 ó 059
060 ó 069
070 ó 079
080 ó 089
090 ó 099
100 ó 109
110 ó 119
120 ó 129
130 ó 139
140 ó 149
150 ó 159
160 ó 169
170 ó 179
180 ó 189
190 ó 199
200 ó 209
210 ó 219
220 ó 229
230 ó 239
240 ó 255
000 ó 009
010 ó 119
120 ó 129
130 ó 255
000 ó 199
200 ó 209
210 ó 219
220 ó 229
230 ó 239
240 ó 255
000 ó 255
000 ó 255
000 ó 255
Percent/Setting
No gobo
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Shaking gobo 6
Shaking gobo 5
Shaking gobo 4
Shaking gobo 3
Shaking gobo 2
Shaking gobo 1
Flow effect
360° Indexing
Clockwise Rotation ~ Slow to Fast
No Function
Counter-Clockwise Rotation ~ Slow to Fast
No Function
Prism
Effect1
Effect2
Effect3
Effect4
Effect5
Effect6
Effect7
Effect8
Effect9
Effect10
Effect11
Effect12
Effect13
Effect14
Effect15
Effect16
Effect17
Effect18
Effect19
Effect20
Prism
No Function
Clockwise rotate ~ slow to fast
No Function
Counter-clockwise rotation ~ slow to fast
Linear Iris
Iris Effect1
Iris Effect2
Iris Effect3
Iris Effect4
Random
0~100%
Fine movement control
0~100%
Continues on the next page
-22-
Q-Spot™ 560-LED User Manual Rev. 08
Operation
Advanced
(Cont.)
Q-Spot™ 560-LED User Manual Rev. 08
16
Strobe
17
Control
000 ó 031
032 ó 063
064 ó 095
096 ó 127
128 ó 159
160 ó 191
192 ó 223
224 ó 255
000 ó 019
020 ó 039
040 ó 059
060 ó 139
140 ó 149
150 ó 159
160 ó 169
170 ó 179
180 ó 189
190 ó 199
200 ó 219
220 ó 235
236 ó 239
240 ó 243
244 ó 247
248 ó 251
252 ó 255
Close
Open
Strobe 0~20Hz
Open
Pulse Effect
Open
Random Effect
Open
Dim setting as set in product
Pan/tilt black activation
Pan/tilt black deactivation
No Function
Auto program 1 (3 s activation delay)
Auto program 2 (3 s activation delay)
Test (3 s activation delay)
Custom program (3 s activation delay)
Sound1
Sound2
Reset (3 s activation delay)
No Function
DIM0 (3 s activation delay)
DIM1 (3 s activation delay)
DIM2 (3 s activation delay)
DIM3 (3 s activation delay)
DIM4 (3 s activation delay)
-23-
Technical Information
5. Technical Information
Product
Maintenance
To maintain optimum performance and minimize wear, the user should clean this product
frequently. Usage and environment are contributing factors in determining the cleaning
frequency.
As a rule, you should clean this product at least twice a month. Dust build up reduces light
output performance and can cause overheating. This can lead to reduced light source life
and increased mechanical wear.
To clean a product, follow the recommendations below:
· Unplug the unit from power.
· Wait until the unit has cooled.
· Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external vents and accessible internal components.
· Clean all external glass lenses with a mild solution of non-ammonia glass cleaner or
isopropyl alcohol.
· Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
· Drag any dirt or grime to the outside of the glass lens.
· Gently polish the glass lens until it is free of haze and lint.
Always dry the external glass lens carefully after cleaning it.
Refrain from spinning this product’s fans using compressed air.
-24-
Q-Spot™ 560-LED User Manual Rev. 08
Technical Information
Troubleshooting Guide
Symptom
Product does not light up
Continuous gobo
rotation
One of the LEDs does
not work
Circuit breaker/fuse
keeps tripping/blowing
Unit does not power up
Unit does not respond to
wired DMX or responds
erratically
Cause(s)
Action(s)
Dimmer fader set to “0”
color fader set to “0”
All colors in CUSTOM mode
are set to “0”
No power
Faulty internal power supply
Faulty main control board
Gobo plate #1 missing or in wrong
location
Faulty LED
Faulty LED module
Faulty LED driver
Excessive circuit load
Increase the value of the dimmer channel
Increase the value of the color channel
Reduce total load placed on the electrical circuit
Short circuit along the power wires
Check electrical wiring
No power
Check for voltage on outlet
Loose or damaged power cord
Check power cord
Blown fuse
Replace fuse
Faulty internal power supply
Send unit for repair
Wrong DMX addressing
Check unit addressing
Damaged DMX cables
Check DMX cables
Wrong polarity on the controller
Check polarity switch settings on the controller
Loose DMX cables
Check cable connections
Non DMX cables
Use only DMX compatible cables
Bouncing signals
Install terminator as suggested
Long cable / low level signal
Install an optically coupled DMX splitter before a
long section of cable or right after the unit with
the strong signal
Too many units
Install an optically coupled DMX splitter after unit
#32
Interference from AC wires
Keep DMX cables separated from power cables
or fluorescent/black lights
Faulty DMX interface board
Send unit for repair
Faulty Display/Main board
Send unit for repair
Increase the values of the colors
Verify external power circuit and wiring
Send unit for repair
Verify Gobo plate #1 is correctly installed
Send unit for repair
If you still experience technical problems after trying the above solutions or if you
need to send the unit for repair, contact CHAUVET® Technical Support.
Q-Spot™ 560-LED User Manual Rev. 08
-25-
Technical Information
Returns
Procedure
You must send the merchandise prepaid, in the original box, and with its original packing
and accessories. CHAUVET® will not issue call tags.
Call CHAUVET® and request a Return Merchandise Authorization (RMA) number before
shipping the product. Be prepared to provide the model number, serial number, and a brief
description of the cause for the return.
Clearly label the package with a Return Merchandise Authorization (RMA) number.
CHAUVET® will refuse any product returned without an RMA number.
DO NOT write the RMA number directly on the box. Instead, write it on a properly
affixed label.
Once you have received the RMA number please include the following information on a
piece of paper inside the box:
· Your name
· Your address
· Your phone number
· The RMA number
· A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate
packaging will be the customer’s responsibility. As a suggestion, proper FedEx packing or
double-boxing is the method CHAUVET® recommends.
CHAUVET® reserves the right to use its own discretion to repair or replace returned
product(s).
Contact Us
World Headquarters
United Kingdom & Ireland
CHAUVET®
CHAUVET® Europe Ltd.
General Information
Address:
Voice:
Fax:
Toll free:
General Information
5200 NW 108th Avenue
Sunrise, FL 33351
(954) 929-1115
(954) 929-5560
(800) 762-1084
Technical Support
Voice:
Fax:
Email:
Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
+44 (0)1773 511115
+44 (0)1773 511110
Voice:
Fax:
Technical Support
(954) 929-1115 (Press 4)
(954) 756-8015
tech@chauvetlighting.com
World Wide Web
Email:
uktech@chauvetlighting.com
World Wide Web
www.chauvetpro.com
-26-
Address:
www.chauvetlighting.co.uk
Q-Spot™ 560-LED User Manual Rev. 08
Technical Specifications
Dimensions and
Weight
Length
Width
Height
Weight
11.7 in (296 mm)
16.1 in (408 mm)
25.0 in (634 mm)
44.1 lbs (20.0 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Electrical
Light Source
Power Supply Type
Range
Voltage Selection
Switching (internal)
100~240 V, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
318 W
302 W
Operating
Fuse
2.60 A
T5 A, 250 V
1.30 A
T5 A, 250 V
Power I/O
US/Worldwide
Europe
Power input connector
IEC
IEC
Power output connector
Power cord plug
N/A
Edison (US)
N/A
Local plug
Type
Power
Lifespan
LED
60 W
50,000 hours
Color
Quantity
Current
White
3
14 A
Parameter
Standard Optics
Illuminance @ 5 m
1,929 lux
Beam angle
Field angle
19º
N/Aº
Pan Range
Tilt Range
Fine Adjustment Option
0~540º
0~270º
Yes (Advanced Mode)
Gobos
Gobo 1 External Diameter
35.8 mm
Gobo 2 External Diameter
32.5 mm
Image Diameter
31.78 mm
Image Diameter
27 mm
Thickness
1.0 mm max.
Thickness
1.0 mm max.
Thermal
Max. External Temperature
Cooling System
104° F (40° C)
Fan Cooled
I/O Connectors
Connector Type
Channel Range
3- and 5-pin XLR
Sockets
13,17
Product Name
Item Code
Item Number
Q-Spot 560-LED
01620436
QSPOT560LED
Photo Optic
Head Movement
DMX
Ordering
Q-Spot™ 560-LED User Manual Rev. 08
-27-
CHAUVET®
5200 NW 108th Avenue
Sunrise, FL 33351 (USA)
(800) 762-1084 – (954) 929-1115
FAX (954) 929-5560
www.chauvetpro.com
Q-Spot™ 560-LED User Manual Rev. 08
January 2013