Sharp PG-D50X3D Operating instructions

PG-D50X3D
PG-D45X3D
Quick Start
MODEL
Introduction
DATA PROJECTOR
Setup
OPERATION MANUAL
Connections
Basic
Operation
Useful
Features
Appendix
IMPORTANT
• For your assistance in reporting the loss
or theft of your Projector, please record
the Model and Serial Number located on
the bottom of the projector and retain this
information.
• Before recycling the packag ing, please
ensure that you have checked the contents of the carton thoroughly against the
list of “Supplied accessories” on page 11.
ii
Model No.:
Serial No.:
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating
a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse
and of the same rating as above, which is also indicated on the pin face
marked or
of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse
cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug
supplied, cut off the mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket
outlet, as a serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow : Earth
Blue
: Neutral
Brown
: Live
As the colours of the wires in the mains lead of this apparatus may not correspond with
the coloured markings identifying the terminals in your plug proceed as follows:
x The wire which is coloured green-and-yellow must be connected to the terminal in the
or coloured green
plug which is marked by the letter E or by the safety earth symbol
or green-and-yellow.
x The wire which is coloured blue must be connected to the terminal which is marked
with the letter N or coloured black.
x The wire which is coloured brown must be connected to the terminal which is marked
with the letter L or coloured red.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
Authorized representative responsible for the European Union Community Market
SHARP ELECTRONICS (Europe) GmbH
Sonninstraße 3, D-20097 Hamburg
E.U. ONLY
iii
The supplied CD-ROM contains operation instructions in English, German, French, Spanish,
Italian, Dutch, Swedish, Portuguese, Korean, Chinese and Arabic. Carefully read through the
operation instructions before operating the projector.
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch,
Spanisch, Italienisch, Niederländisch, Schwedisch, Portugiesisch, Koreanisch, Chinesisch
und Arabisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors
sorgfältig durch.
Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, français,
espagnol, italien, néerlandais, suédois, portugais, coréen, chinois et arabe. Veuillez lire attentivement ces instructions avant de faire fonctionner le projecteur.
El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán, francés,
español, italiano, holandés, sueco, portugués, coreano, chino y árabe. Lea cuidadosamente
las instrucciones de operación antes de utilizar el proyector.
Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese, spagnolo,
italiano, olandese, svedese, portoghese, coreano, cinese e arabo. Leggere attentamente le
istruzioni per l’uso prima di usare il proiettore.
De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Spaans,
Italiaans, Nederlands, Zweeds, Portugees, Koreaans, Chinees en Arabisch. Lees de
handleiding zorgvuldig door voor u de projector in gebruik neemt.
Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska, franska,
spanska, italienska, holländska, svenska, portugisiska, koreanska, kinesiska och arabiska.
Läs noga igenom bruksanvisningen innan projektorn tas i bruk.
O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês,
Espanhol, Italiano, Holandês, Sueco, Português, Coreano, Chinês e Árabe. Leia
cuidadosamente todas as instruções de operação antes de operar o projetor.
iv
Introduction
Introduction
Before using the projector, please read this operation manual carefully.
ENGLISH
There are two important reasons for prompt warranty registration of your new
SHARP Projector, using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts,
service and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection,
modification, or recall that SHARP may be required to give under the 1972
Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT
“LIMITED WARRANTY” CLAUSE.
U.S.A. ONLY
WARNING:
High brightness light source. Do not stare into the beam of light, or view
directly. Be especially careful that children do not stare directly into the
beam of light.
WARNING: To reduce the risk of fire or electric shock, do not
expose this product to rain or moisture.
See bottom of projector.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage”
within the product's enclosure that may
be of sufficient magnitude to constitute
a risk or electric shock to persons.
The exclamation point within a triangle
is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the
literature accompanying the product.
WARNING:
This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
WARNING:
FCC Regulations state that any unauthorized changes or modifications
to this equipment not expressly approved by the manufacturer could
void the user's authority to operate this equipment.
U.S.A. ONLY
The enclosed computer cable must be used with the device. The cable is
provided to ensure that the device complies with FCC Class A verification.
U.S.A. ONLY
1
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the operation manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at
his own expense.
U.S.A. ONLY
PRODUCT DISPOSAL
This product utilizes tin-lead solder, and lamp containing a small
amount of mercury. Disposal of these materials may be regulated due
to environmental considerations. For disposal or recycling information,
please contact your local authorities, the Electronics Industries Alliance:
www.eiae.org, the lamp recycling organization www.lamprecycle.org, or
Sharp at 1-800-BE-SHARP.
U.S.A. ONLY
Caution Concerning Lamp Replacement
■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time.
The period of time up to failure largely varies depending on the individual lamp and/or the condition
and the frequency of use. It is important to note that failure can often result in the bulb cracking.
■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
■ Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector
Dealer or Service Center to assure safe operation.
■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In
case of exposure to the gas, consult a doctor as soon as possible.
Caution
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may
cause burns or injury.
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to
fully cool before removing the lamp unit.
• Do not touch the glass surface of the lamp unit or the inside of the projector.
• Do not loosen other screws except for the lamp unit cover and lamp unit.
• Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and
continue to use the same lamp, this may cause the lamp to become damaged or explode.
■ Carefully change the lamp by following the instructions described on pages 55 to 57.
* If you wish, you may have the lamp replaced at your nearest Sharp Authorized Projector
Dealer or Service Center.
* If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized
Projector Dealer or Service Center for repair.
2
Introduction
How to Read this Operation Manual
■ The specifications are slightly different, depending on the model. However, you can connect
and operate all models in the same manner.
• In this operation manual, the illustration and the screen display are simplified for explanation, and
may differ slightly from the actual display.
Using the Menu Screen
MENU/HELP button
Adjustment buttons (P/R/O/Q)
ENTER button
RETURN button
ENTER button
Adjustment buttons
(P/R/O/Q)
RETURN button
• Press RETURN to return
to the previous screen
when the menu is
displayed.
Buttons used in
this operation
MENU/HELP button
Button used in
this step
Menu Selections (Adjustments)
Example: Adjusting “Bright”.
• This operation can also be performed by using the buttons on the projector.
1
2
Press MENU/HELP.
• The “Picture” menu screen for the selected
Input mode is displayed.
Press Q or O and select
“Picture” to adjust.
Example: “Picture” screen menu for
COMPUTER (RGB) input
Menu item
Picture
SCR
Picture Mode
Contrast
Bright
Red
Blue
CLR Temp
BrilliantColor TM
C.M.S. Setting
C.M.S.
DNR
Eco+Quiet
Reset
SEL./ADJ.
PRJ
Net.
Help
On-screen
display
Standard
0
0
0
0
0
1
On
Off
On
ENTER
END
38
Info .........Indicates safeguards for using the projector.
Note ....... Indicates additional information for setting up and operating the
projector.
For Future Reference
Maintenance
P. 52
Troubleshooting
PP. 59 and 60
Index
P. 64
3
Contents
Preparing
Introduction
Useful Features
How to Read this Operation Manual ......3
Contents .................................................4
IMPORTANT SAFEGUARDS ..................6
How to Access the PDF Operation
Manuals..............................................10
Accessories ..........................................11
Part Names and Functions ...................12
Operating with the Remote Control......32
Projector................................................. 12
Rear View ............................................... 13
Inserting the Batteries ............................. 15
Usable Range ......................................... 15
Quick Start
Menu Items...........................................35
Using the Menu Screen ........................38
Quick Start ...........................................16
Menu Selections (Adjustments) ............... 38
Setup and Projection .............................. 16
Picture Adjustment (“Picture” Menu) ....40
Setup
Setting up the Projector .......................18
Video Setup............................................ 18
Setting up the Projector .......................... 18
Standard Setup (Front Projection) ........... 18
Ceiling-mount Setup ............................... 18
Projection (PRJ) Mode ............................ 19
Screen Size and Projection Distance ...... 20
Connections
Connecting the Projector to
Other Equipment ................................21
Controlling the Projector by
a Computer ........................................24
Connecting the Power Cord .................25
Using
Basic Operation
Turning the Projector On/Off ................26
Turning the Projector On ......................... 26
Turning the Power Off (Putting the
Projector into Standby Mode) .............. 26
Image Projection ..................................27
Adjusting the Projected Image ................ 27
Correcting Trapezoidal Distortion ............ 28
Switching the Input Mode ....................... 29
Adjusting the Volume .............................. 29
Displaying the Black Screen and
Turning Off the Sound Temporarily ....... 29
Resize Mode .......................................... 30
4
Displaying and Setting the
Break Timer ......................................... 32
Displaying the Pointer ............................. 32
Using the Spot Function ......................... 32
Switching the Eco+Quiet Mode .............. 32
Auto Sync (Auto Sync Adjustment) ......... 33
Freezing a Moving Image ........................ 33
Selecting the Picture Mode ..................... 33
Displaying an Enlarged Portion of
an Image ............................................. 33
Using the Remote Control as the
Wireless Computer Mouse ................... 34
Selecting the Picture Mode ..................... 40
Adjusting the Image ................................ 41
Adjusting the Color Temperature............. 41
Adjusting the Colors ............................... 41
Progressive............................................. 42
Reducing Image Noise (DNR) ................. 42
Eco+Quiet .............................................. 42
Adjusting the Projected Image
(“SCR - ADJ” Menu)...........................43
Setting the Resize Mode......................... 43
Adjusting the Image Position .................. 43
Keystone Correction ............................... 43
Setting the Overscan .............................. 43
Setting the On-screen Display ................ 43
Closed Caption ...................................... 44
Selecting the Background Image ............ 44
Reversing/Inverting Projected Images ..... 44
DLP® LinkTM ............................................ 44
DLP® LinkTM Invert .................................. 44
Setting the Video Setup .......................... 44
Selecting the On-screen Display
Language ............................................ 44
Adjusting the Projector Function
(“PRJ - ADJ” Menu) ...........................45
Auto Sync (Auto Sync Adjustment) ......... 45
Auto Power Off Function ........................ 45
Auto Restart Function ............................. 45
STANDBY Mode ..................................... 45
Setting the Confirmation Sound
(System Sound) ................................... 45
Audio Output Type Setting ...................... 46
Speaker Setting ...................................... 46
Audio Input ............................................. 46
Selecting the Transmission Speed
(RS-232C) ........................................... 46
Fan Mode Setting ................................... 46
Introduction
System Lock Function ............................ 46
Checking the Lamp Life Status ............... 47
Keylock Function .................................... 48
Setting up the Projector Network
Environment (“Network” Menu)..........49
Setting a Password ................................ 49
DHCP Client Setting ............................... 50
TCP/IP Setting........................................ 50
Confirming the Projector Information....... 50
Troubleshooting with the
“Help” Menu.......................................51
Utilizing the “Help” Menu Functions ........ 51
Reference
Appendix
Maintenance .........................................52
Maintenance Indicators ........................53
Regarding the Lamp .............................55
Lamp...................................................... 55
Caution Concerning the Lamp ................ 55
Replacing the Lamp ............................... 55
Removing and Installing the
Lamp Unit ............................................ 56
Resetting the Lamp Timer ...................... 57
Computer Compatibility Chart .............58
Troubleshooting ....................................59
For SHARP Assistance .........................61
Specifications .......................................62
Dimensions ...........................................63
Index .....................................................64
5
IMPORTANT SAFEGUARDS
CAUTION: Please read all of these instructions before you operate this
product and save these instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered
and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the
safeguards incorporated in this product, observe the following basic rules for its
installation, use and servicing.
1. Read Instructions
All the safety and operating instructions
should be read before the product is
operated.
2. Retain Instructions
The safety and operating instructions
should be retained for future reference.
3. Heed Warnings
All warnings on the product and in the
operating instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should
be followed.
5. Cleaning
Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for
example, near a bath tub, wash bowl, kitchen
sink, or laundry tub; in a wet basement; or
near a swimming pool; and the like.
8. Accessories
Do not place this product on an unstable
cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury to a
child or adult, and serious damage to the
product. Use only with a cart, stand, tripod,
bracket, or table recommended by the
manufacturer, or sold with the product. Any
mounting of the product should follow the
manufacturer's instructions, and should use a
mounting accessory recommended by the
manufacturer.
9. Transportation
A product and cart
combination should be
moved with care. Quick
stops, excessive force, and
uneven surfaces may
cause the product and cart
combination to overturn.
6
10. Ventilation
Slots and openings in the cabinet are provided
for ventilation to ensure reliable operation of
the product and to protect it from overheating,
and these openings must not be blocked or
covered. The openings should never be
blocked by placing the product on a bed, sofa,
rug, or other similar surface. This product
should not be placed in a built-in installation
such as a bookcase or rack unless proper
ventilation is provided or the manufacturer's
instructions have been adhered to.
11. Power Sources
This product should be operated only from
the type of power source indicated on the
marking label. If you are not sure of the
type of power supply to your home, consult
your product dealer or local power
company. For products intended to operate
from battery power, or other sources, refer
to the operating instructions.
12. Grounding or Polarization
This product is provided with one of the
following types of plugs. If the plug should
fail to fit into the power outlet, please contact
your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug
with a grounding terminal.
This plug will only fit into a grounding
type power outlet.
13. Power-Cord Protection
Power-supply cords should be routed so
that they are not likely to be walked on or
pinched by items placed upon or against
them, paying particular attention to cords
at plugs, convenience receptacles, and the
point where they exit from the product.
14. Lightning
For added protection for this product during
a lightning storm, or when it is left
unattended and unused for long periods of
time, unplug it from the wall outlet and
disconnect the cable system. This will
prevent damage to the product due to
lightning and power-line surges.
Do not overload wall outlets, extension cords,
or integral convenience receptacles as this
can result in a risk of fire or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this
product through openings as they may touch
dangerous voltage points or short-out parts
that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
17. Servicing
Do not attempt to service this product
yourself as opening or removing covers
may expose you to dangerous voltage or
other hazards. Refer all servicing to
qualified service personnel.
18. Damage Requiring Service
Unplug this product from the wall outlet
and refer servicing to qualified service
personnel under the following conditions:
a. When the power-supply cord or plug is
damaged.
b. If liquid has been spilled, or objects
have fallen into the product.
c. If the product has been exposed to rain
or water.
d. If the product does not operate normally
by following the operating instructions.
Adjust only those controls that are
covered by the operating instructions,
as an improper adjustment of other
controls may result in damage and will
often require extensive work by a
qualified technician to restore the
product to normal operation.
e. If the product has been dropped or
damaged in any way.
f. When the product exhibits a distinct
change in performance, this indicates a
need for service.
19. Replacement Parts
Introduction
15. Overloading
When replacement parts are required, be
sure the service technician has used
replacement parts specified by the
manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may result in
fire, electric shock, or other hazards.
20. Safety Check
Upon completion of any service or repairs
to this product, ask the service technician
to per form safety checks to determine that
the product is in proper operating
condition.
21. Wall or Ceiling Mounting
This product should be mounted to a wall
or ceiling only as recommended by the
manufacturer.
22. Heat
This product should be situated away from
heat sources such as radiators, heat
registers, stoves, or other products
(including amplifiers) that produce heat.
• DLP® and the DLP logo are registered trademarks of Texas Instruments and
BrilliantColorTM and DLP® LinkTM are trademarks of Texas Instruments.
• Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the
United States and/or other countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the
United States.
• Adobe® Reader® is a trademark of Adobe Systems Incorporated.
• Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or
other countries.
• PJLink is a registered trademark or an application trademark in Japan, the United States,
Canada, E.U., China and/or other countries/regions.
• All other company or product names are trademarks or registered trademarks of their
respective companies.
• Some IC chips in this product include confidential and/or trade secret property belonging
to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute,
reverse engineer, reverse assemble or discompile the contents thereof.
7
Observe the following safeguards when setting up your
projector.
Caution concerning the lamp unit
■ Potential hazard of glass particles if lamp
ruptures. In case of lamp rupture, contact
your nearest Sharp Authorized Projector
Dealer or Service Center
for replacement.
See “Regarding the Lamp”
on page 55.
Caution concerning the setup of the
projector
■ For minimal servicing and to maintain high
image quality, SHARP recommends that
this projector be installed in an area free
from humidity, dust and cigarette smoke.
When the projector is subjected to these
environments, the vents and lens must be
cleaned more often. As long as the
projector is regularly cleaned, use in these
environments will not reduce the overall
operation life of the unit. Internal cleaning
should only be performed by a Sharp
Authorized Projector Dealer or Service
Center.
Rest your eyes occasionally.
■ Continuously watching the screen for long
hours will cause eye strain. Take regular
breaks to rest your eyes.
Do not set up the projector in places
exposed to direct sunlight or bright light.
■ Position the screen so that it is not in direct
sunlight or room light. Light falling directly
on the screen washes out the colors,
making viewing difficult. Close the curtains
and dim the lights when setting up the
screen in a sunny or bright room.
Caution regarding placing of the projector
■ Place the projector on a level site within the
adjustment range (9 degrees) of the
adjustment foot.
■ After the projector is purchased, a faint
smell from the vent may appear when the
power is first turned on. This is normal and
is not a malfunction. It will disappear after
the projector is used for a while.
8
When using the projector in highaltitude areas such as mountains (at
altitudes of approximately 1,500
meters (4,900 feet) or more)
■ When you use the projector in high-altitude
areas with thin air, set “Fan Mode” to
“High”. Neglecting this can affect the
longevity of the optical system.
■ Use the projector at altitudes of 2,300
meters (7,500 feet) or less.
Warning about placing the projector in
a high position
■ When placing the projector in a high
position, make certain it is carefully secure
to avoid personal injury caused by the
projector falling down.
Do not subject the projector to hard
impact and/or vibration.
■ Protect the lens so as not to hit or damage
the surface of the lens.
Avoid locations with extremes of
temperature.
■ The operating temperature of the projector
is from 41°F to 95°F (+5°C to +35°C).
■ The storage temperature of the projector is
from –4°F to 140°F (–20°C to +60°C).
Do not block the exhaust and intake
vents.
■ Allow at least 11 13/16 inches (30 cm) of
space between the exhaust vent and the
nearest wall or obstruction.
■ Ensure that the intake vent and the exhaust
vent are not obstructed.
■ If the cooling fan becomes obstructed, a
protection circuit will automatically put the
projector into Standby mode to prevent
overheat damage. This does not indicate a
malfunction. (See pages 53 and 54.)
Remove the projector power cord from the
wall outlet and wait at least 10 minutes.
Place the projector where the intake and
exhaust vents are not blocked, plug the
power cord back in and turn on the
projector. This will return the projector to
the normal operating condition.
Using the projector in other countries
■ If you are not to use the projector for a long
time or before moving the projector, make
certain you unplug the power cord from the
wall outlet, and disconnect any other
cables connected to it.
■ Do not carry the projector by holding the
lens.
■ When storing the projector, ensure that you
close the lens shutter.
■ Do not expose the projector to direct
sunlight or place next to heat sources.
Doing so may affect the cabinet color or
cause deformation of the plastic cover.
■ The power supply voltage and the shape of
the plug may vary depending on the region
or country you are using the projector in.
When using the projector overseas, make
sure you use an appropriate power cord for
the country you are in.
Other connected equipment
■ When connecting a computer or other
audio-visual equipment to the projector,
make the connections AFTER unplugging
the power cord of the projector from the
AC outlet and turning off the equipment to
be connected.
■ Please read the operation manuals of the
projector and the equipment to be
connected for instructions on how to make
the connections.
Introduction
Caution regarding usage of the projector
Temperature monitor function
■ If the temperature inside the projector
increases, due to blockage of the air vents,
or the setting location, the temperature
warning indicator will blink. And if the
temperature keeps on rising, “
” will
illuminate in the lower left corner of the
picture with the temperature warning
indicator blinking. If this state continues,
the lamp will turn off, the cooling fan will
run and then the projector will enter
Standby mode. Refer to “Maintenance
Indicators” on pages 53 and 54 for details.
Info
• The cooling fan regulates the internal
temperature, and its performance is automatically
controlled. The sound of the fan may change
during projector operation due to changes in the
fan speed. This does not indicate malfunction.
Closed Caption uses Bitstream Vera fonts
Copyright (c) 2003 by Bitstream, Inc. All Rights Reserved. Bitstream Vera is a trademark of Bitstream, Inc.
Permission is hereby granted, free of charge, to any person obtaining a copy of the fonts accompanying this
license (“Fonts”) and associated documentation files (the “Font Software”), to reproduce and distribute the
Font Software, including without limitation the rights to use, copy, merge, publish, distribute, and/or sell
copies of the Font Software, and to permit persons to whom the Font Software is furnished to do so, subject
to the following conditions:
The above copyright and trademark notices and this permission notice shall be included in all copies of one
or more of the Font Software typefaces.
The Font Software may be modified, altered, or added to, and in particular the designs of glyphs or
characters in the Fonts may be modified and additional glyphs or characters may be added to the Fonts,
only if the fonts are renamed to names not containing either the words “Bitstream” or the word “Vera”.
This License becomes null and void to the extent applicable to Fonts or Font Software that has been
modified and is distributed under the “Bitstream Vera” names.
The Font Software may be sold as part of a larger software package but no copy of one or more of the Font
Software typefaces may be sold by itself.
THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT, TRADEMARK, OR OTHER
RIGHT. IN NO EVENT SHALL BITSTREAM OR THE GNOME FOUNDATION BE LIABLE FOR ANY CLAIM,
DAMAGES OR OTHER LIABILITY, INCLUDING ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
FROM, OUT OF THE USE OR INABILITY TO USE THE FONT SOFTWARE OR FROM OTHER DEALINGS IN
THE FONT SOFTWARE.
Except as contained in this notice, the names of Gnome, the Gnome Foundation, and Bitstream Inc., shall
not be used in advertising or otherwise to promote the sale, use or other dealings in this Font Software
without prior written authorization from the Gnome Foundation or Bitstream Inc., respectively. For further
information, contact: fonts at gnome dot org.
9
How to Access the PDF Operation Manuals
PDF operation manuals in several languages are included in the CD-ROM. To
utilize these manuals, you need to install Adobe® Reader ® on your computer
(Windows® or Macintosh®).
Please download Adobe® Reader ® from the Internet (http://www.adobe.com).
Accessing the PDF Manuals
For Windows®:
Insert the CD-ROM in the CD-ROM drive.
Double click the “My Computer” icon.
Double click the “CD-ROM” drive.
When you want to view the operation
manual
1) Double click the “MANUALS” folder.
2) Double click the language (name of the
folder) that you want to view.
3) Double click the pdf file to access the
projector manuals.
When you want to view the SETUP
MANUAL
1) Double click the “SETUP” folder.
2) Double click the language (name of the
folder) that you want to view.
3) Double click the pdf file to access the
SETUP MANUAL.
For Macintosh®:
Insert the CD-ROM in the CD-ROM drive.
Double click the “CD-ROM” icon.
When you want to view the operation
manual
1) Double click the “MANUALS” folder.
2) Double click the language (name of the
folder) that you want to view.
3) Double click the pdf file to access the
projector manuals.
When you want to view the SETUP
MANUAL
1) Double click the “SETUP” folder.
2) Double click the language (name of the
folder) that you want to view.
3) Double click the pdf file to access the
SETUP MANUAL.
Note
• If the desired pdf file cannot be opened by double clicking the mouse, start Adobe® Reader ® first,
then specify the desired file using the “File”, “Open” menu.
SETUP MANUAL
Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for details.
Connecting Pin Assignments ······················································· 2
RS-232C Specifications and Commands ····································· 4
Setting up the Projector Network Environment ···························· 9
Controlling the Projector via LAN ··············································· 15
Setting up the Projector Using RS-232C or Telnet ····················· 20
Resetting the Lamp Timer of the Projector via LAN···················· 30
Troubleshooting·········································································· 32
10
Introduction
Accessories
Supplied accessories
Two R-6 batteries
(“AA” size, UM/SUM-3,
HP-7 or similar)
Remote control
<RRMCGA829WJSA>
Power cord*
(1)
For U.S. and
Canada, etc.
(6' (1.8 m))
<QACCDA007WJPZ>
(2)
For Europe,
except U.K.
(6' (1.8 m))
<QACCVA011WJPZ>
RGB cable
(10' (3.0 m))
<QCNWGA086WJPZ>
(3)
(4)
For U.K. and
Singapore
(6' (1.8 m))
<QACCBA036WJPZ>
For Australia, New
Zealand and Oceania
(6' (1.8 m))
<QACCLA018WJPZ>
* Use the power cord that corresponds to the wall outlet in your country.
• Operation manuals (this manual <TINS-E670WJZZ>, OPERATION MANUAL FOR STEREOSCOPIC
3D PROJECTION <TINS-E500WJZZ> and CD-ROM <UDSKAA128WJZZ>)
Note
• Codes in “< >” are Replacement parts codes.
Optional accessories
■ Lamp unit
■ Ceiling-mount adaptor
■ Ceiling-mount bracket
■ Ceiling-mount unit
■ Ceiling-mount extension tube
■ Remote receiver
■ 3 RCA to mini D-sub 15 pin cable (10 n (3.0 m))
AN-D500LP <for PG-D50X3D>
AN-D400LP <for PG-D45X3D>
AN-60KT
AN-XGCM55 (for U.S.A. only)
AN-TK201 <for AN-60KT>
AN-TK202 <for AN-60KT>
AN-EP101B <for AN-XGCM55>
(for U.S.A. only)
AN-MR2
AN-C3CP2
Note
• Some of the optional accessories may not be available depending on the region. Please check with
your nearest Sharp Authorized Projector Dealer or Service Center.
11
Part Names and Functions
Numbers in Z refer to the main pages in this operation manual where the
topic is explained.
Projector
Top View
AUTO SYNC
button
For automatically
adjusting images
when connected
to a computer.
33
STANDBY/ON
button
For turning the
power on and
putting the
projector into
Standby mode.
26
Power
indicator
26, 53
Lamp
indicator
26, 53
Temperature
warning
indicator
KEYSTONE button
For entering the Keystone
Correction mode.
38
ENTER button
For setting items selected
or adjusted on the menu.
29
INPUT buttons (P/R)
For switching Input mode.
38
Adjustment buttons
(P/R/O/Q)
For selecting menu items.
29
53
ECO+QUIET
32
button
For lowering the
noise of the cooling
fan and extending
the lamp life.
Front View
Exhaust vent
28
38
VOL (Volume)
buttons (–O/Q+)
For adjusting the
speaker sound
level.
RETURN button
For returning to the
previous menu screen
during menu operations.
38, 51
MENU/HELP button
For displaying
adjustment and
setting screens, and
help screen.
52
Zoom ring
27
For enlarging/
reducing the picture.
15
Remote control
sensor
52
Intake vent
Focus ring
For adjusting
the focus.
27
Adjustment foot
27
27
HEIGHT
ADJUST lever
Lens shutter
29
27
Adjustment foot
12
Introduction
Numbers in Z refer to the main pages in this operation manual where the
topic is explained.
22 VIDEO input terminal
Rear View
Terminal for connecting
video equipment.
Terminals
22 S-VIDEO input terminal
MONITOR OUT terminal
23
(Output terminal for computer
RGB, component and DVI analog
signals. Shared for COMPUTER/
COMPONENT and DVI-I)
Terminal for connecting a monitor.
COMPUTER/COMPONENT input
terminal
Terminal for computer RGB and
component signals.
DVI-I input
21
terminal
22
Terminal for DVI
digital, computer
RGB and
component signals.
AUDIO 1 input
23
terminal
AUDIO OUT
23
terminal
Audio output terminal of equipment
connected to the audio input terminal.
AC socket
25
Connect the
supplied power cord.
Speaker
46
23 AUDIO 2 input terminal
21
22
25 LAN terminal
Terminal for controlling the
projector using a computer
via network.
34 USB terminal
Terminal
connecting with
the USB terminal
on the computer
for using the
supplied remote
control as the
computer mouse.
24 RS-232C terminal
Terminal for controlling the
projector using a computer.
46 Speaker
Security bar
Kensington Security
Standard connector
Carrying handle
Remote control
sensor
Terminal for connecting video
equipment with an
S-video terminal.
15
Using the Carrying Handle
When transporting the projector, carry it by the carrying handle on the
side.
• Always close the lens shutter to prevent damage to the lens when
transporting the projector.
• Do not lift or carry the projector by the lens as this may damage the
lens.
Using the Kensington Lock
• This projector has a Kensington Security Standard connector for use with a Kensington
MicroSaver Security System. Refer to the information that came with the system for
instructions on how to use it to secure the projector.
13
Part Names and Functions (Continued)
STANDBY button
26
For putting the projector into
the Standby mode.
26 ON button
29
COMPUTER, DVI,
S-VIDEO, VIDEO buttons
For switching to the
respective Input modes.
33 FREEZE button
BREAK TIMER button 32
For displaying the
break time.
MAGNIFY buttons
33
For enlarging/reducing
part of the image.
PAGE UP/PAGE
34
DOWN buttons
Same as the [Page Up] and
[Page Down] keys on a
computer keyboard, when with
the USB connection (using a
USB cable or the optional
remote receiver).
POINTER button
For displaying the
pointer.
32
MOUSE/Adjustment
buttons (P/R/O/Q)
34
38
• For moving the
computer cursor when with the USB
connection (using a USB cable or the
optional remote receiver).
• For selecting and adjusting menu
items.
L-CLICK/EFFECT
button
34
32
• For the Left click
when with the USB connection
(using a USB cable or the optional
remote receiver).
• For changing the pointer or spot
area.
28
KEYSTONE button
For entering the
Keystone Correction mode.
33
AUTO SYNC button
For automatically
adjusting images when
connected to a computer.
32
ECO+QUIET button
For lowering the noise
of the cooling fan and
extending the lamp life.
14
For turning the power
on.
For freezing images.
29 AV MUTE button
For temporarily
displaying a black
screen and turning off
the sound.
29 VOL +/– (Volume)
buttons
For adjusting the
speaker sound level.
32 SPOT button
For displaying the
spotlight.
38 ENTER button
For setting items
selected or adjusted
on the menu.
34 R-CLICK/RETURN
38 button
• For the Right click when
with the USB connection
(using a USB cable or
the optional remote
receiver).
• For returning to the
previous menu screen
during menu
operations.
38 MENU/HELP button
51 For displaying
adjustment and setting
screens, and help
screen.
30 RESIZE button
For switching the
picture size (NORMAL,
STRETCH, etc.).
3D MODE button
See the OPERATION MANUAL
FOR STEREOSCOPIC 3D
PROJECTION provided
separately.
33 PICTURE MODE
button
For selecting the
appropriate picture.
1
Pull down the tab on the cover and remove the
cover towards the direction of the arrow.
2
Insert the batteries.
3
Insert the lower tab of the cover into the opening,
and lower the cover until it clicks in place.
Introduction
Inserting the Batteries
• Insert the batteries making sure the polarities correctly match
the m and n marks inside the battery compartment.
Incorrect use of the batteries may cause them to leak or explode.
Please follow the precautions below
Caution
• Danger of explosion if battery is incorrectly replaced.
Replace only with alkaline or manganese batteries.
• Insert the batteries making sure the polarities correctly match the m and n marks inside the battery
compartment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
• Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak.
Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then
remove them using a cloth.
• The batteries included with this projector may run down in a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries.
• Remove the batteries from the remote control if you will not be using the remote control for a long time.
• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
Remote control sensor
Usable Range
The remote control can be used to control the
projector within the ranges shown in the
illustration.
Note
• Another remote control sensor is located
on the rear of the projector. (See page 13.)
• The signal from the remote control can be
reflected off a screen for easy operation.
However, the effective distance of the signal
may differ depending on the screen material.
When using the remote control
• Ensure that you do not drop it or expose it to
moisture or high temperature.
• The remote control may malfunction under a
fluorescent lamp. In this case, move the
projector away from the fluorescent lamp.
30°
30°
23 n (7 m)
Remote control signal
transmitters
Remote control
15
Quick Start
This section shows the basic operation (projector connecting with the computer). For details,
see the page described below for each step.
Setup and Projection
In this section, connection of the projector and the computer is explained using one example.
3
STANDBY/ON
button
8
5 KEYSTONE button
8 STANDBY button
3 ON button
5 Adjustment buttons
6 COMPUTER button
(P/R/O/Q)
6 INPUT buttons
4 Zoom ring
4 Focus ring
5 Adjustment buttons
(P/R/O/Q)
4 HEIGHT
5
ADJUST lever
1. Place the projector facing a wall or a screen
KEYSTONE button
BP. 18
2. Connect the projector to the computer and plug the power
cord into the AC socket of the projector
When connecting equipment other than a computer, see pages
22 and 23.
BPP. 21, 25
3. Open the lens shutter fully and then turn the projector on
On the projector
On the remote control
BP. 26
16
4. Adjust the projected image
1
2
3
Adjusting the focus.
Adjusting the height.
Adjusting the picture size.
BP. 27
Quick Start
5. Correct trapezoidal distortion
Correcting trapezoidal distortion using Keystone Correction.
On the projector
Shrinks
upper side.
Shrinks
lower side.
On the remote control
BP. 28
6. Select the Input mode
Select the “COMPUTER” using INPUT on the projector or COMPUTER on the remote
control.
On the
projector
On the remote
control
INPUT list
On-screen display (RGB)
INPUT
COMPUTER
D
DVI-D Computer
D
DVI-D Video
• When you press INPUT on the projector, the INPUT list appears.
Press / to switch the Input mode.
COMPUTER
RGB
1024 × 768
BP. 29
7. Turn the computer on
8. Turn the power off
Press STANDBY/ON on the projector or STANDBY on the remote control, and then press
the button again while the confirmation message is displayed to put the projector into
Standby mode.
On-screen display
On the remote
On the
control
projector
BP. 26
17
Setting up the Projector
Video Setup
If using this projector outside the U.S.A., please change setting to “0 IRE” in Video Setup. (See
page 44.)
Setting up the Projector
For optimal image quality, position the projector perpendicular to the screen with the projector's
feet flat and level. Doing so will eliminate the need for Keystone correction and provide the best
image quality. (See page 28.)
Standard Setup (Front Projection)
■ Place the projector at the required distance from the screen
according to the desired picture size. (See page 20.)
Example of standard setup
Side View
Screen
H
Lens center
L
Note
• Refer to page 20 for additional information concerning “Screen Size and Projection Distance”.
Ceiling-mount Setup
■ It is recommended that you use the
optional Sharp ceiling-mount adaptor and
unit for this installation. Before mounting
the projector, contact your nearest Sharp
Authorized Projector Dealer or Service
Center to obtain the recommended ceilingmount adaptor and unit (sold separately).
18
Projection (PRJ) Mode
The projector can use any of the 4 projection modes shown in the diagram below. Select the
mode most appropriate for the projection setting in use. (You can set the PRJ mode in “SCRADJ” menu. See page 44.)
■ Ceiling mounted, front projection
[Menu item ➞ “Ceiling + Front”]
■ Table mounted, rear projection
(with a translucent screen)
[Menu item ➞ “Rear”]
■ Ceiling mounted, rear projection
(with a translucent screen)
[Menu item ➞ “Ceiling + Rear”]
Setup
■ Table mounted, front projection
[Menu item ➞ “Front”]
Indication of the Projection Image Size and Projection Distance
Example: 4:3 Signal Input (Normal Mode)
Picture Size
500" (1270 cm)
400
(101"×300"
6 cm
×
762
cm)
200" (508 cm)
32"
(81 cm×24"
× 61 cm
)
49
(1 '0
4. "
9
m
)
Projection
Distance
9'
(3 10
.0 "–
m 1
– 3 1'
.4 4"
19
m
)
(6 '7
.0 "–
m 2
– 6 2'
.9 7"
m
)
40" (102 cm)
160
(406"×120"
cm ×
80"×
305
cm)
(203 60"
cm ×
152 c
m)
3'
(1 11
.2 "–
m 4
– 1 '6
.4 "
m
)
100" (254 cm)
19
Setting up the Projector (Continued)
Screen Size and Projection Distance
4:3 Signal Input (Normal Mode)
Picture (Screen) size
Diag. [ Ȥ ]
Width
Height
500" (1270 cm) 1016 cm (400") 762 cm (300")
400" (1016 cm) 813 cm (320") 610 cm (240")
300" (762 cm)
610 cm (240") 457 cm (180")
250" (635 cm)
508 cm (200") 381 cm (150")
200" (508 cm)
406 cm (160") 305 cm (120")
150" (381 cm)
305 cm (120") 229 cm (90")
120" (305 cm)
244 cm (96") 183 cm (72")
100" (254 cm)
203 cm (80") 152 cm (60")
80" (203 cm)
163 cm (64") 122 cm (48")
70" (178 cm)
142 cm (56") 107 cm (42")
60" (152 cm)
122 cm (48")
91 cm (36")
40" (102 cm)
81 cm (32")
61 cm (24")
Projection distance [L]
Distance from the lens center
Minimum [L1] Maximum [L2] to the bottom of the image [H]
14.9 m (49' 0")
—
11 cm (4 15/32")
12.0 m (39' 3") 13.8 m (45' 3")
9 cm (3 37/64")
9.0 m (29' 5") 10.3 m (33' 11")
7 cm (2 11/16")
7.5 m (24' 6") 8.6 m (28' 3")
6 cm (2 15/64")
6.0 m (19' 7") 6.9 m (22' 7")
5 cm (1 51/64")
4.5 m (14' 9") 5.2 m (17' 0")
3 cm (1 11/32")
3.6 m (11' 9") 4.1 m (13' 7")
3 cm (1 5/64")
3.0 m (9' 10") 3.4 m (11' 4")
2 cm (57/64")
2.4 m (7' 10") 2.8 m (9' 1")
2 cm (23/32")
2.1 m (6' 10") 2.4 m (7' 11")
2 cm (5/8")
1.8 m (5' 11") 2.1 m (6' 9")
1 cm (17/32")
1.2 m (3' 11") 1.4 m (4' 6")
1 cm (23/64")
F : Picture size (diag.) (in/cm)
L: Projection distance (m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the lens center to the bottom of the image (cm/in)
The formula for picture
[m/cm]
L1 (m) = 0.02989 F
L2 (m) = 0.03446 F
H (cm) = 0.02273 F
size and projection distance
[Feet/inches]
L1 (ft) = 0.02989 F / 0.3048
L2 (ft) = 0.03446 F / 0.3048
H (in) = 0.02273 F / 2.54
16:9 Signal Input (Stretch Mode)
Picture (Screen) size
Projection distance [L]
Distance from the lens center Adjustable range of
Diag. [ Ȥ ]
Width
Height
Minimum [L1] Maximum [L2] to the bottom of the image [H] image position [S]
400" (1016 cm) 886 cm (349") 498 cm (196") 13.0 m (42' 9") 15.0 m (49' 3")
93 cm (36 37/64")
±83 cm (±32 11/16")
7
70 cm (27 /16")
±62 cm (±24 33/64")
300" (762 cm) 664 cm (261") 374 cm (147") 9.8 m (32' 1") 11.3 m (36' 11")
250" (635 cm) 553 cm (218") 311 cm (123") 8.1 m (26' 8")
9.4 m (30' 9")
58 cm (22 55/64")
±52 cm (±20 27/64")
19
6.5 m (21' 4")
7.5 m (24' 8")
46 cm (18 /64")
±42 cm (±16 11/32")
200" (508 cm) 443 cm (174") 249 cm (98")
150" (381 cm) 332 cm (131") 187 cm (74")
4.9 m (16' 0")
5.6 m (18' 6")
35 cm (13 23/32")
±31 cm (±12 1/4")
31
3.9 m (12' 10") 4.5 m (14' 9")
28 cm (10 /32")
±25 cm (±9 13/16")
120" (305 cm) 266 cm (105") 149 cm (59")
100" (254 cm) 221 cm (87") 125 cm (49")
3.3 m (10' 8")
3.8 m (12' 4")
23 cm (9 9/64")
±21 cm (±8 11/64")
2.6 m (8' 7")
3.0 m (9' 10")
19 cm (7 5/16")
±17 cm (±6 17/32")
80" (203 cm) 177 cm (70") 100 cm (39")
2.0 m (6' 5")
2.3 m (7' 5")
14 cm (5 31/64")
±12 cm (±4 29/32")
60" (152 cm) 133 cm (52")
75 cm (29")
1.3 m (4' 3")
1.5 m (4' 11")
9 cm (3 21/32")
±8 cm (±3 17/64")
40" (102 cm)
89 cm (35")
50 cm (20")
F : Picture size (diag.) (in/cm)
L: Projection distance (m/ft)
L1: Minimum projection distance (m/ft)
L2: Maximum projection distance (m/ft)
H: Distance from the lens center to the bottom of the image (cm/in)
S: Adjustable range of image position (cm/in) See page 43.
The formula for picture
[m/cm]
L1 (m) = 0.03256 F
L2 (m) = 0.03754 F
H (cm) = 0.23231 F
S (cm) = ±0.20754 F
size and projection distance
[Feet/inches]
L1 (ft) = 0.03256 F / 0.3048
L2 (ft) = 0.03754 F / 0.3048
H (in) = 0.23231 F / 2.54
S (in) = ±0.20754 F / 2.54
Note
• Refer to page 18 concerning “Projection distance [L]” and “Distance from the lens center to the
bottom of the image [H]”.
• Allow a margin of error in the values in the diagrams above.
20
Connecting the Projector to Other Equipment
Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet
and turn off the equipment to be connected. After making all connections, turn on the projector
and then the other pieces of equipment. When connecting a computer, ensure that it is the last
equipment to be turned on after all the connections are made.
IMPORTANT:
Ensure that the appropriate Input mode has been selected on the projector before
you turn on the connected equipment.
• For more details of connection and cables, refer to the operation manual of the connecting equipment.
• You may need other cables or connectors not listed below.
Terminals on the Projector
Computer
Terminal on
connected equipment
Cable
RGB
output
terminal
RGB cable (supplied)
RGB
output
terminal
mini D-sub 15 pin to DVI cable
(commercially available)
DVI digital
output
terminal
Connections
Equipment
Terminal on the
projector
COMPUTER/
COMPONENT
DVI-I
DVI Digital cable (commercially available)
Note
• When you connect external equipment to the projector using a DVI digital cable, the image will look
different from its original appearance. In this case, switch to the Plug-and-Play data. (See page 37.)
• See page 58 “Computer Compatibility Chart” for a list of computer signals compatible with the
projector. Use with computer signals other than those listed may cause some of the functions to not
work.
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest
Macintosh Dealer.
• Depending on the computer you are using, an image may not be projected unless the
computer's external output port is switched on (e.g. Press “Fn” and “F5” keys
simultaneously when using a SHARP notebook computer). Refer to the specific instructions in
your computer's operation manual to enable your computer's external output port.
21
Connecting the Projector to Other Equipment (Continued)
Equipment
Video equipment
Terminal on
connected equipment
HDMI output
terminal
Cable
Terminal on the
projector
HDMI to DVI cable
(commercially available)
DVI-I
DVI digital
output
terminal
Component
video output
terminal
S-video
output
terminal
Video output
terminal
Camera/Video game
Component
video
output
terminal
DVI Digital cable (commercially available)
3 RCA to mini D-sub 15 pin cable
(optional, AN-C3CP2)
COMPUTER/
COMPONENT
S-video cable (commercially available)
S-VIDEO
Video cable (commercially available)
VIDEO
Cables for a camera or a video game/3 RCA to COMPUTER/
mini D-sub 15 pin cable (optional, AN-C3CP2) COMPONENT
RCA adaptor plug
(commercially available)
Cables for a camera or a video game
S-VIDEO
Cables for a camera or a video game
VIDEO
S-video
output
terminal
Video
output
terminal
Note
• While the projector is connected to video equipment that has an HDMI output terminal, only the video
signal can be input to the projector. (Connect the AUDIO input terminal for audio input.)
• Depending on specifications of video equipment or the DVIÙHDMI digital cable, the signal
transmission may not work property. (The HDMI specification does not support all connections to
video equipment that has HDMI digital output terminal using a DVIÙHDMI digital cable.)
• For details on compatibility for connection, see support information on DVI connection provided by
the video equipment manufacturer.
• When you connect external equipment to the projector using a DVI digital cable, the image will look
different from its original appearance. In this case, switch to the Plug-and-Play data. (See page 37.)
• When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a
commercially available cable that fits in the projector terminal you want to connect.
• The projector does not support RGBC signals via the Euro-scart.
22
Equipment
Audio equipment
Terminal on
connected equipment
Cable
ø3.5 mm
audio output
terminal
ø3.5 mm stereo or mono audio cable
(commercially available or available
as Sharp service part QCNWGA038WJPZ)
RCA audio
output
terminal
RCA audio cable (commercially available)
Terminal on the
projector
AUDIO 1
AUDIO 2
Cables for a camera or a video game
Audio
output
terminal
Monitor
RGB
input
terminal
ø3.5 mm
audio input
terminal
RCA audio
input
terminal
MONITOR OUT
Connections
Amplifier
RGB cable (supplied or commercially
available)
ø3.5 mm stereo or mono audio cable
(commercially available or available
as Sharp service part QCNWGA038WJPZ)
AUDIO OUT
ø3.5 mm stereo minijack to RCA audio cable
(commercially available)
Note
• When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm
stereo audio cable.
• You can select “Audio 1” or “Audio 2” for “Audio Input” in the “PRJ-ADJ” menu. (See page 46.)
• RGB signals and Component signals can be output to the monitor.
23
Controlling the Projector by a Computer
When the RS-232C terminal on the projector is connected to a computer with an RS-232C serial
control cable (cross type, commercially available), the computer can be used to control the
projector and check the status of the projector. Refer to the “SETUP MANUAL” contained on the
supplied CD-ROM for “RS-232C Specifications and Commands”.
When connecting to a computer using an RS-232C serial control cable
To RS-232C terminal
Computer
To RS-232C terminal
RS-232C serial control cable (cross type, commercially available)
Note
• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the
operation manual of the computer for details.
• Refer to pages 2 to 8 of the “SETUP MANUAL” contained on the supplied CD-ROM for “Connecting
Pin Assignments” and “RS-232C Specifications and Commands”.
Info
• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This
may damage your computer or projector.
• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on.
This may damage your computer.
24
When connecting to the LAN terminal using a LAN cable
TX/RX LED (yellow)
Illuminates when transmitting/receiving data.
LINK LED (green)
Illuminates when linked.
* To ensure safety, do not connect the LAN terminal
with any cables that may cause excessive voltage
such as a telephone line.
Hub
or
Computer
To LAN terminal
Connections
LAN cable (Category 5 type,
commercially available)
Note
• When connecting to a hub, use a straight-through Category 5 (CAT.5) type cable (commercially
available).
• When connecting to a computer, use a cross-over Category 5 (CAT.5) type cable (commercially
available).
Connecting the Power Cord
Plug the supplied power cord into the
AC socket on the rear of the projector.
Then plug into AC outlet.
AC socket
Power cord
(supplied)
To AC outlet
25
Turning the Projector On/Off
Info
Turning the Projector On
Note that the connections to external
equipment and power outlet should be
done before performing the operations
written below. (See pages 21 to 25.)
Open the lens shutter fully and press
STANDBY/ON on the projector or ON
on the remote control.
• When “Auto Restart” is set to “On”:
If the power cord is unplugged from the outlet
or the breaker switch is turned off when the
projector is on, then the projector
automatically turns on when the power cord
is plugged into the AC outlet or the breaker
switch is turned on. (See page 45.)
• English is the factory default language. If you
want to change the on-screen display to
another language, change the language
according to the procedure on page 44.
• The power indicator illuminates green.
• After the lamp indicator illuminates, the projector
is ready to start operation.
Power indicator
STANDBY/ON button
Note
• About the Lamp Indicator
The lamp indicator illuminates to indicate the
status of the lamp.
Green: The lamp is on.
Blinking in green: The lamp is warming up.
Red: The lamp is shut down
abnormally or the lamp should be
replaced.
• When switching on the projector, a slight
flickering of the image may be experienced
within the first minute after the lamp has been
illuminated. This is normal operation as the
lamp's control circuitry is stabilising the lamp
output characteristics. It should not be
regarded as faulty operation.
• If the projector is put into Standby mode and
immediately turned on again, the lamp may
take some time to start projection.
• When System Lock is set, the keycode input
box appears. To cancel the keycode setting,
input the keycode that you have already set.
See page 46 for details.
Turning the Power Off (Putting
the Projector into Standby Mode)
Press STANDBY/ON on the projector
or STANDBY on the remote control,
then press that button again while the
confirmation message is displayed, to
put the projector into Standby mode.
• The projector cannot be turned on while cooling.
Lamp indicator
STANDBY
button
ON button
On-screen display (confirmation message)
Info
• Direct Power Off function:
You can unplug the power cord from the AC
outlet even if the cooling fan is still running.
26
Image Projection
Adjusting the Projected Image
Zoom ring
Focus ring
1 Adjusting the Focus
You can adjust the focus with the focus
ring on the projector.
Rotate the focus ring to adjust the
focus while watching the projected
image.
2 Adjusting the Height
The height of the projector can be
adjusted using the adjustment feet.
When the screen is above the projector,
the projection image can be made higher
by adjusting the projector.
1
Lift the projector to adjust its
height while lifting the HEIGHT
ADJUST lever.
HEIGHT ADJUST
lever
2
Basic
Operation
Remove your hands from the
HEIGHT ADJUST lever of the
projector after its height has
been finely adjusted.
• The angle of projection is adjustable up to
9 degrees from the surface on which the
projector is placed.
Make small
adjustments.
Note
• When adjusting the height of the projector,
trapezoidal distortion occurs. Follow the
procedures in Keystone Correction to correct
the distortion. (See pages 28 and 43.)
3 Adjusting the Picture Size
You can adjust the picture size using the
zoom ring on the projector.
Rotate the zoom ring to enlarge or
shrink the picture size.
Info
• Do not apply too much pressure on the
projector when the front adjustment feet
come out.
• When lowering the projector, be careful not to
get your fingers caught in the area between
the adjustment feet and the projector.
• Hold the projector firmly while lifting or carrying.
• Do not hold by the lens area.
27
Image Projection (Continued)
Correcting Trapezoidal
Distortion
Adjustment buttons
(P/R/O/Q)
When the image is projected either from
the top or from the bottom towards the
screen at an angle, the image becomes
distorted trapezoidally. The function for
correcting trapezoidal distortion is called
Keystone Correction.
Note
• The Keystone Correction can be adjusted up
to an angle of approximately ±40 degrees and
the screen can also be set up to an angle of
approximately ±40 degrees (when the Resize
mode is set to “NORMAL” (see page 30)).
1
Press KEYSTONE to enter the
Keystone Correction mode.
• You can also display the on-screen display
of the Keystone Correction mode with
KEYSTONE on the projector.
2
RETURN button
KEYSTONE button
On-screen display
(Keystone Correction mode)
KEYSTONE
ADJUST
0
END
Shrinks upper side.
(Move the slide bar in the + direction.)
Press P/Q or O/R to adjust the
Keystone Correction.
• You can also adjust the Keystone
Correction using the adjustment buttons
on the projector.
Note
Shrinks lower side.
(Move the slide bar in the - direction.)
• To return to the default setting, press
RETURN while the on-screen display of the
Keystone Correction mode is on the screen.
3
28
Press KEYSTONE.
• The on-screen display of the Keystone
Correction mode will disappear.
• You can also use KEYSTONE on the
projector.
Info
• While adjusting the image using Keystone
Correction, straight lines and the edges of the
image may appear jagged.
Switching the Input Mode
COMPUTER, DVI,
S-VIDEO, VIDEO
buttons
Select the appropriate Input mode for the
connected equipment.
Press COMPUTER, DVI, S-VIDEO or
VIDEO on the remote control to select
the Input mode.
AV MUTE button
VOL +/– (Volume)
buttons
• When you press INPUT on the projector or DVI
on the remote control, the INPUT list appears.
Press P/R to switch the Input mode.
Adjusting the Volume
Press VOL +/– on the remote control
or –O/Q+ on the projector to adjust
the volume.
Note
On-screen display
Basic
Operation
• Pressing VOL–/–O will lower the volume.
• Pressing VOL+/Q+ will raise the volume.
• When the projector is connected to external
equipment, the volume level of the external
equipment changes in accordance with the
volume level of the projector. Set the projector's
volume to the lowest level when turning the
projector on/off or when changing the input signal.
• When you do not want to output the sound
from the projector's speaker while the
projector is connected to external equipment,
set “Speaker” in “PRJ-ADJ” menu to “Off”.
(See page 46.)
Displaying the Black Screen
and Turning Off the Sound
Temporarily
Press AV MUTE on the remote control
or close the lens shutter to temporarily
display a black screen and turn off the
sound.
On-screen display
Note
• Pressing AV MUTE again will turn the
projected image back on.
• When you close the lens shutter, the projector will
be AV Mute mode and then the projector will be
turned off automatically after about 30 minutes.
29
Image Projection (Continued)
Resize Mode
This function allows you to modify or customize the Resize mode to enhance the input
image. Depending on the input signal, you can choose a desired image.
Press RESIZE.
RESIZE
button
• See page 43 for setting on menu screen.
COMPUTER
Main resolution
NORMAL
FULL
SVGA (800 × 600)
4:3 aspect ratio
XGA (1024 × 768)
SXGA (1152 × 864)
1024 × 768
STRETCH
—
—
1152 × 864
768 × 576
1024 × 576
1600 × 1200
SXGA (1280 × 1024)
968 × 768
1280 × 1024
1280 × 720
1024 × 576
1280 × 720
—
—
1360 × 768
1024 × 578
1360 × 768
—
—
1366 × 768
1024 × 576
1366 × 768
—
1280 × 768
1024 × 614
1280 × 768
960 × 576
1280 × 800
1024 × 640
1280 × 800
922 × 576
Input signal
Computer
BORDER
800 × 600
UXGA (1600 × 1200)
Other aspect ratios
DOT BY DOT
Image type
1024 × 768
For 4:3 screen
NORMAL
720 × 576
—
1024 × 576
For 16:9 screen
FULL
DOT BY DOT
—*2
—*2
BORDER
STRETCH
Resolution
lower than
XGA
XGA
Resolution
higher than
XGA
*1
*1
4:3 aspect ratio
SXGA (1280 × 1024)
5:4 aspect ratio
*1
1280 × 720
—*2
1360 × 768
1366 × 768
1280 × 768
1280 × 800
*1
16:10 aspect ratio
: Cutout area on which images cannot be projected
: Area where the signals are off screen
*1 The Image Shift function can be used for these images.
*2 Same as NORMAL mode
30
—*2
16:9 aspect ratio
*1
*1
VIDEO/DTV
Input signal
Video/DTV
Image type
For 4:3 screen
NORMAL
AREA ZOOM
For 16:9 screen
V-STRETCH
BORDER
STRETCH
*1
*1
*1
*1
*1
*1
4:3 aspect ratio
480I, 480P,
576I, 576P,
NTSC, PAL,
SECAM
Squeeze
Letter box
720P, 1035I,
1080I, 1080P
*1
16:9 aspect ratio
—*2
16:9 aspect ratio
—*2
*1
540P
(4:3 aspect ratio in 16:9)
About Copyrights
• When using the Resize function to select an image size with a different aspect ratio to a TV
program or video image, the image will look different from its original appearance. Keep this
in mind while choosing an image size.
• The use of the Resize or Keystone Correction function to compress or stretch the image for
commercial purposes/public displays in a café, hotel, etc. may be an infringement of
copyright protected by law for copyright holders. Please use caution.
Basic
Operation
: Cutout area on which images cannot be projected
: Area on which the image is not included in the original signals
*1 The Image Shift function can be used for these images.
*2 Same as NORMAL mode.
31
Operating with the Remote Control
BREAK TIMER button
FREEZE button
MAGNIFY buttons
Displaying the Pointer
1
POINTER button
• Press EFFECT to change the pointer icon
(5 types).
SPOT button
Adjustment buttons
(P/R/O/Q)
EFFECT button
PICTURE MODE button
ECO+QUIET button
Press POINTER and press P/R/
O/Q on the remote control to
move the pointer.
Star
2
Finger1
Finger2
Heart
Underline
Press POINTER again.
• The pointer will disappear.
AUTO SYNC button
Using the Spot Function
Displaying and Setting the
Break Timer
1
1
Press BREAK TIMER.
Press SPOT and press P/R/O/Q
on the remote control to move
the spot area.
• Press EFFECT to change the spot area
size (3 types).
• The timer starts to count down from 5
minutes.
1/9
1/25
1/8
On-screen display
2
Press P/R/O/Q to adjust the
length of the break time.
• Increases with P or Q
2
Press SPOT again.
• The spot area will disappear.
5 minutes ➞ 6 minutes ➞ 60 minutes
• Shortens with O or R
4 minutes ➞ 3 minutes ➞1 minute
• The break time can be set in units of one
minute (up to 60 minutes).
Canceling the break timer display function
Press BREAK TIMER.
Note
• The Break Timer is not available while the
projector is operating the following functions.
- Auto Sync
- Freeze
- AV Mute
32
Switching the Eco+Quiet
Mode
Press ECO+QUIET to switch the
Eco+Quiet mode between on and off.
• When the Eco+Quiet mode is set to “ON”, the
sound of the cooling fan will turn down, the power
consumption will decrease, and the lamp life will
extend.
Note
• Refer to “Eco+Quiet” on page 42 for details.
Auto Sync
(Auto Sync Adjustment)
Displaying an Enlarged
Portion of an Image
Auto Sync function works when detecting
input signal after the projector turns on.
Graphs, tables and other portions of
projected images can be enlarged. This
is helpful when providing more detailed
explanations.
Press AUTO SYNC to manually adjust
with Auto Sync function.
1
Note
Press
MAGNIFY on the
remote control.
• Enlarges the image.
• Pressing
or
MAGNIFY enlarges
or reduces the projected image.
• When the optimum image cannot be achieved
with Auto Sync adjustment, use the help
menu for manual adjustments. (See page 51.)
Note
.
Press
×1 ×2
Freezing a Moving Image
×3
Press
1
Press FREEZE.
2
Press FREEZE again to return to
the moving image from the
currently connected device.
×4
.
• You can change the location of the
enlarged image using P, R, O and Q.
• The projected image is frozen.
2
Press RETURN on the remote
control to cancel the operation.
• The magnification then returns to u1.
Note
Selecting the Picture Mode
Press PICTURE MODE.
• When pressing PICTURE MODE, the Picture
mode changes in the following order:
STANDARD
PRESENTATION
MOVIE
GAME
sRGB*
Useful
Features
You can select the appropriate Picture
mode for the projected image, such as
movie or video game.
• The selectable magnifications differ
depending on the input signal.
• In the following cases, the image will
return to the normal size (u1).
- When switching the Input mode.
- When RETURN has been pressed.
- When the input signal is changed.
- When the input signal resolution and
refresh rate (vertical frequency)
change.
- When the Resize mode is changed.
- When the Picture mode is changed.
- When the Progressive mode is
changed.
Note
• See page 40 for details on the Picture mode.
* “sRGB” is displayed only when RGB signal is input.
33
Operating with the Remote Control (Continued)
Using the Remote Control as the Wireless Computer Mouse
When connecting the projector and the computer with a USB cable, you can use the
remote control as the computer mouse.
If the computer is placed too far away from the projector to be connected via the USB
cable, the remote receiver (optional, AN-MR2) makes it possible to operate the
projector with the remote control. For details, see the operation manual of the
receiver.
Connecting with a USB cable
Computer
To USB terminal
To USB terminal
Remote receiver
(optional, AN-MR2)
or
USB cable
(commercially available or available as
Sharp service part QCNWGA014WJPZ)
The mouse pointer can be
operated in the following way
after it is connected.
■ When moving the cursor
PAGE UP/
PAGE DOWN buttons
MOUSE/Adjustment
buttons (
//?/_)
Press MOUSE/Adjustment buttons (P/R/O/Q).
■ When left-clicking
Press L-CLICK.
■ When right-clicking
Press R-CLICK.
R-CLICK button
■ When your computer supports only a
one-click mouse (such as Macintosh)
Press L-CLICK or R-CLICK.
L-CLICK and R-CLICK have common function.
L-CLICK button
■ When using [Page Up] or [Page Down]
Same as the [Page Up] and [Page Down] keys on a computer keyboard.
Press PAGE UP or PAGE DOWN.
Note
• This function only works with the Microsoft® Windows® OS and Mac OS®. However, this function
does not work with the following operation systems that do not support USB.
• Versions earlier than Windows® 95
• Versions earlier than Windows® NT4.0
• Versions earlier than Mac OS® 8.5
• You cannot use this function when displaying the menu screen.
• Confirm that the computer recognizes the USB connection.
34
Menu Items
The following shows the items that can be set in the projector.
“Picture” menu
Main menu
Picture
PAGE 1
Picture
Page 40
SCR
Picture Mode
Contrast
Bright
Color
Tint
Sharp
Red
Blue
PRJ
Net.
Sub menu
Standard
Presentation
Movie
Game
sRGB*1
Picture Mode
Page 40
Help
Standard
0
0
0
0
0
0
0
SEL./ADJ.
ENTER
END
Contrast
-30
+30
Bright
-30
+30
Color
-30
+30 *2
Tint
-30
+30 *2
Sharp
-30
+30 *2
Red
-30
+30
Blue
-30
+30
Page 41
PAGE 2
Picture
SCR
PRJ
Picture Mode
Net.
Help
CLR Temp
BrilliantColor™
0
1
CLR Temp
BrilliantColor TM
C.M.S. Setting
C.M.S.
Progressive
DNR
Eco+Quiet
Reset
-1
1
0
2
Page 41
Standard
Page 41
C.M.S. Setting [On/Off]
On
3D Progressive
Off
On
Page 41
C.M.S.
Page 41
Progressive
2D Progressive
3D Progressive
Film Mode
*2
Page 42
SEL./ADJ.
ENTER
END
DNR
Off
Level 1
Level 2
Page 42
On
Off
Eco+Quiet
“C.M.S.”
Page 42
Reset
C. M. S.
C. M. S. - Hue
C. M. S. - Saturation
C. M. S. - Value
Reset
C.M.S.-Hue
SEL./ADJ.
Return
0
0
0
0
0
0
-30
+30
Y
-30
+30
C.M.S.-Saturation
G
-30
+30
Page 41
C
-30
+30
B
-30
+30
M
-30
+30
C.M.S.-Value
Page 41
Reset
ENTER
END
Reset
Useful
Features
R
Y
G
C
B
M
Reset
R
Page 41
*1 Item when inputting RGB signal through
COMPUTER or DVI.
*2 Items when inputting component signal through
COMPUTER or DVI, or when selecting S-VIDEO or
VIDEO.
35
Menu Items (Continued)
“Screen adjustment (SCR-ADJ)” menu
Pict.
SCR-ADJ
PRJ
Resize
Image Shift
Keystone
Help
Main menu
SCR - ADJ
Border
Page 43
0
0
Sub menu
Resize
Page 43
Image Shift
On
On
Off
Logo
Front
Off
Overscan
OSD Display
Closed Caption
Background
PRJ Mode
DLP® Link TM
DLP® Link TM Invert
Video Setup
Language
SEL./ADJ.
Net.
Keystone
+96
-80
+80
Page 43
Overscan [On/Off]
Page 43
OSD Display [On/Off]
0 IRE
English
ENTER
-96
Page 43
Normal
Full
Dot By Dot
Area Zoom
V-Stretch
Border
Stretch
Page 43
END
Closed Caption
Page 44
Background
Page 44
PRJ Mode
Page 44
Off
CC1
CC2
Logo
Blue
None
Front
Ceiling + Front
Rear
Ceiling + Rear
DLP® LinkTM [On/Off]
Page 44
DLP® LinkTM Invert
Page 44
Video Setup
Page 44
Language
Page 44
0 IRE
7.5 IRE
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português
polski
Magyar
Türkçe
“Projector adjustment (PRJ-ADJ)” menu
Pict.
SCR
Auto Sync
Auto Power Off
Auto Restart
STANDBY Mode
System Sound
Audio Out
Speaker
Audio Input
RS-232C
Fan Mode
System Lock
Lamp Timer(Life)
SEL./ADJ.
PRJ-ADJ
0 h
ENTER
Net.
Help
On
On
On
Standard
On
VAO
On
Audio 1
9600bps
Normal
Disable
0 min 100%
END
Main menu
PRJ - ADJ
Page 45
Sub menu
Auto Sync [On/Off]
Page 45
Auto Power Off [On/Off]
Page 45
Auto Restart [On/Off]
Page 45
STANDBY Mode
Page 45
Standard
Eco
System Sound [On/Off]
Page 45
Audio Out
Page 46
FAO
VAO
Speaker [On/Off]
Page 46
Audio Input
Page 46
RS-232C
Page 46
Fan Mode
Page 46
System Lock
[Enable/Disable]
Page 46
Lamp Timer(Life)
36
Page 47
Audio 1
Audio 2
9600bps
38400bps
115200bps
Normal
High
Main menu
“Network” menu
Password [Enable/Disable]
Network
Pict.
SCR
PRJ
Network
Password
Disable
DHCP Client
Off
Help
Page 49
Page 49
DHCP Client [On/Off]
Page 50
TCP/IP
Page 50
TCP/IP
MAC Address X X : X X : X X : X X : X X : X X
MAC Address
Page 50
Projector
XX-XXXX
Projector
Page 50
SEL./ADJ.
ENTER
END
“Help” menu
Pict.
SCR
PRJ
Net.
Help
“Help” menu n Page 51
There is no picture or audio
Vertical stripes or flickering image appear
Data image is not centered
Color is faded or poor
Picture is dark
The image is distorted
It is difficult to hear audio
• Vertical stripes or flickering image appear
Auto Sync/Clock/Phase
Reset all adjustments to default settings
SEL
SEL.
ENTER
The items you can set with the
“Help” menu
END
• Data image is not centered
COMPUTER or DVI-Analog input
Auto Sync/H-Pos/V-Pos/Resolution
DVI-D input
Switch to Plug-and-Play data
* Switch to Plug-and-Play data in the following
cases.
DVI-D Computer input
Standard : Aspect ratio 4:3 or 5:4 signals
such as 1024x768
Enhanced1 : Wide-screen signals such as
1280x800 are prioritized.
Enhanced2 : Wide-screen signals such as
1366x768 are prioritized.
DVI-D Video input
Standard : Normal
Enhanced : Select this item when no
image is projected in Standard
mode.
Useful
Features
• Color is faded or poor
COMPUTER or DVI input
Signal type: Auto/RGB/Component
S-VIDEO or VIDEO input
Video System: Auto/PAL/SECAM/
NTSC3.58/NTSC4.43/
PAL-M/PAL-N/PAL-60
DVD-D input
Dynamic range: Auto/Standard/Enhanced
* The selectable items vary depending on the input
signal and the selected Input mode.
• It is difficult to hear audio
Balance/Treble/Bass
37
Using the Menu Screen
MENU/HELP button
Adjustment buttons (P/R/O/Q)
ENTER button
RETURN button
ENTER button
Adjustment buttons
(P/R/O/Q)
RETURN button
• Press RETURN to return
to the previous screen
when the menu is
displayed.
MENU/HELP button
Menu Selections (Adjustments)
Example: Adjusting “Bright”.
• This operation can also be performed by using the buttons on the projector.
1
2
Press MENU/HELP.
• The “Picture” menu screen for the selected
Input mode is displayed.
Press Q or O and select
“Picture” to adjust.
Example: “Picture” screen menu for
COMPUTER (RGB) input
Menu item
Picture
SEL./ADJ.
38
SCR
Picture Mode
Contrast
Bright
Red
Blue
CLR Temp
BrilliantColor TM
C.M.S. Setting
C.M.S.
DNR
Eco+Quiet
Reset
PRJ
Net.
Help
Standard
0
0
0
0
0
1
On
Off
On
ENTER
END
3
Press P or R and select “Bright”
to adjust.
• The selected item is highlighted.
Picture
SCR
PRJ
Picture Mode
Contrast
Bright
Red
Blue
CLR Temp
BrilliantColor TM
C.M.S. Setting
C.M.S.
DNR
Eco+Quiet
Reset
SEL./ADJ.
Net.
Help
Standard
0
0
0
0
0
1
On
Off
On
Single ADJ
END
Items to be adjusted
Pict.
To adjust the projected
image while watching it
SCR-ADJ
Resize
Image Shift
Keystone
PRJ
Net.
Help
Border
0
0
Press ENTER.
• The selected item (e.g. “Bright”) is
displayed by itself at the bottom of the
screen.
• When pressing P or R, the following item
(“Red” after “Bright”) will be displayed.
Press ENTER.
The item displayed by itself
Picture
Note
Bright
SEL./ADJ.
0
Rtn. Menu
END
• Press ENTER again to return to the
previous screen.
4
Press O or Q to adjust the item
selected.
• The adjustment is stored.
Press MENU/HELP.
• The menu screen will disappear.
SCR
SEL./ADJ.
PRJ
Net.
Help
Standard
0
15
0
0
0
1
Useful
Features
5
Picture
Picture Mode
Contrast
Bright
Red
Blue
CLR Temp
BrilliantColor TM
C.M.S. Setting
C.M.S.
DNR
Eco+Quiet
Reset
On
Off
On
Single ADJ
END
Note
• The MENU/HELP button is not available while the projector is operating:
- Auto Sync/Break Timer/Freeze/AV Mute
39
Picture Adjustment (“Picture” Menu)
Menu operation n Page 38
Q PAGE1
Q PAGE2
Picture
1
2
SCR
Picture Mode
Contrast
Bright
Color
Tint
Sharp
Red
Blue
SEL./ADJ.
PRJ
Net.
Help
Picture
Standard
0
0
0
0
0
0
0
ENTER
SCR
PRJ
Picture Mode
3
2
4
5
6
7
END
Net.
Help
Standard
0
1
CLR Temp
BrilliantColor TM
C.M.S. Setting
C.M.S.
Progressive
DNR
Eco+Quiet
Reset
SEL./ADJ.
On
3D Progressive
Off
On
ENTER
END
1 Selecting the Picture Mode
Selectable
items
Description
The default settings of each item when selecting Picture Mode
CLR Temp
BrilliantColorTM
0
1
Off
Presentation Brightens portions of image for
more enhanced presentations.
0
2
Off
Movie
Gives natural tint to the
projected image.
–1
0
On
Game
Gives sharpness to the
projected image.
0
1
Off
*sRGB
For high fidelity reproduction of
images from a computer.
–
–
Off
Standard
For standard image
Eco+Quiet
• “sRGB” is displayed only when RGB signal is input.
• You can set or adjust each item in the “Picture” menu to your preference. Any changes you make are
retained in memory.
Note
• You can also press PICTURE MODE on the remote control to select the Picture mode. (See page 33.)
• *sRGB is an international standard of color reproduction regulated by the IEC (International
Electrotechnical Commission). As the fixed color area has been decided by the IEC, the images are
displayed in a natural tint based on an original image, when “sRGB” is selected.
For additional information about the sRGB function, visit “http://www.srgb.com/”.
You cannot set the items, “Red”, “Blue”, “CLR Temp”, “BrilliantColorTM”, when “sRGB” is selected.
Info
• When “sRGB” is selected, the projected image may become dark, but this does not indicate a
malfunction.
40
Menu operation n Page 38
2 Adjusting the Image
Adjustment
items
Contrast
Bright
Color*1
Tint*1
Sharp*1
Red*2
Blue*2
BrilliantColor™*2 *3
O button
Q button
For less
contrast.
For less
brightness.
For less color
intensity.
For making skin
tones purplish.
For less
sharpness.
For weaker red.
For more
contrast.
For more
brightness.
For more color
intensity.
For making skin
tones greenish.
For more
sharpness.
For stronger
red.
For stronger
blue.
For making the
effect stronger.
For weaker
blue.
For making the
effect weaker.
*1 Not displayed in the RGB input mode.
*2 Not adjustable/selectable when selecting “sRGB”.
*3 BrilliantColor™ uses Texas Instruments'
BrilliantColor™ technology. As the BrilliantColor™
level is increased, the image becomes brighter
while the color reproduction is kept at a high level.
4 Adjusting the Colors
This function adjusts each of the six main
colors that comprise the color wheel, altering
their “Hue”, “Saturation”, or “Value”.
Selectable items
Description
C.M.S.-Hue
Sets the hue of the main colors.
C.M.S.-Saturation
Sets the saturation of the main
colors
C.M.S.-Value
Sets the brightness of the main
colors.
Reset
The adjustments of “Hue”,
“Saturation” and “Value” of all
colors are reset to the default
setting.
Adjusting “Hue”, “Saturation”, or “Value”.
1
Select “On” for “C.M.S. Setting” in the “Picture”
menu and then press ENTER.
2
Select “C.M.S.” in the “Picture” menu and then
press ENTER.
3
Press P or R to select either “Hue”, “Saturation”, or
“Value” and then press ENTER.
4
Select the color to be adjusted with P or R and
adjust it with O or Q.
Note
• “Red”, “Blue”, “BrilliantColorTM” and “CLR
Temp” cannot be set when “sRGB” is
selected.
• To reset all adjustment items, select “Reset”
and press ENTER.
Adjusting the Color
Temperature
–1
Description
For lower color temperature for
warmer, reddish incandescent-like
images.
0
1
For higher color temperature for
cooler, bluish, fluorescent-like images.
Main colors
R (Red)
O button
Closer to magenta
Q button
Closer to yellow
Y (Yellow)
Closer to red
Closer to green
G (Green)
Closer to yellow
Closer to cyan
C (Cyan)
Closer to green
Closer to blue
B (Blue)
Closer to cyan
Closer to magenta
M (Magenta) Closer to blue
Closer to red
• When “Saturation” is selected, the selected
color becomes
O: lighter. Q: thicker.
• When “Value” is selected, the selected color
becomes
O: darker. Q: brighter.
• To reset the adjustment values of each color to
the default settings, select “Reset” and press
ENTER.
Useful
Features
Selectable
items
Example of adjusting the “Hue”
Note
• Values on “CLR Temp” are only for general
standard purposes.
41
Picture Adjustment (“Picture” Menu)
(Continued)
Menu operation n Page 38
5 Progressive
Selectable
items
Description
2D
Progressive
Useful to display fast-moving images
such as sports.
3D
Progressive
Useful to display relatively slowmoving images such as drama and
documentary more clearly.
Film Mode
Reproduces the image of film source*
clearly. Displays the optimized image
of film transformed with three-two pull
down (NTSC and PAL60Hz) or twotwo pull down (PAL50Hz and SECAM)
enhancement to Progressive mode
images.
* The film source is a digital video recording with the
original encoded as is at 24 frames/second. The
projector can convert this film source to
progressive video at 60 frames/second with NTSC
and PAL60Hz or at 50 frames/second with
PAL50Hz and SECAM to play back a highdefinition image.
Note
• In NTSC or PAL60Hz, even if the 3D
Progressive mode has been set, the three-two
pull down enhancement will be enabled
automatically when the film source has been
entered.
• When the image is blurred or noisy, switch to
the optimal mode.
Info
• This function is available for 480I and 576I
signals using COMPUTER/COMPONENT or
DVI input.
• This function is available for all signals with
S-VIDEO and VIDEO input.
42
6 Reducing Image Noise (DNR)
Video digital noise reduction (DNR) provides
high quality images with minimal dot crawl
and cross color noise.
Selectable
items
Description
Off
The DNR function is not activated.
Level 1
Sets the DNR level for viewing a
clearer picture.
Level 2
Note
Set “DNR” to “Off” in the following cases:
• When the image is blurry.
• When the contours and colors of moving
images drag.
• When TV broadcasts with weak signals are
projected.
7 Eco+Quiet
Selectable
items
Brightness and Power consumption
On
Approx. 75%
Off
100%
Note
• When “Eco+Quiet” is set to “On”, the fan
sound and power consumption are lower than
they are when “Off” is selected. (Projection
brightness decreases as shown in the chart.)
Adjusting the Projected Image (“SCR - ADJ” Menu)
Menu operation n Page 38
Pict.
1
2
3
4
5
6
7
8
9
0
SCR-ADJ
Resize
Image Shift
Keystone
PRJ
Help
Border
0
0
Select “Keystone” on the “SCR-ADJ”
menu and adjust with the slide bar.
0 IRE
English
ENTER
3 Keystone Correction
When the image is projected either from the top
or from the bottom towards the screen at an
angle, the image becomes distorted trapezoidally.
The function for correcting trapezoidal distortion
is called Keystone Correction.
On
On
Off
Logo
Front
Off
Overscan
OSD Display
Closed Caption
Background
PRJ Mode
DLP® Link TM
DLP® Link TM Invert
Video Setup
Language
SEL./ADJ.
Net.
END
1 Setting the Resize Mode
Use this function to stretch the image
vertically or horizontally or when the edges of
the image cannot be seen.
See page 28 for details of Keystone Correction.
Note
• The Keystone Correction can be adjusted up
to an angle of approximately ±40 degrees
(when “Resize” is set to “Normal”).
• You can also press KEYSTONE on the
remote control or on the projector to adjust
Keystone Correction.
Note
• For details of the Resize mode, see pages
30 and 31.
• You can also press RESIZE on the remote
control to set the Resize mode. (See page 30.)
2 Adjusting the Image
Position
You can move the projected image vertically.
4 Setting the Overscan
This function allows you to set the overscan area
(display area).
Selectable
items
Description
On
The input area is displayed without the
screen edges.
Off
The whole input area is displayed.
Note
O button
Q button
5 Setting the On-screen
Display
Note
• This function only works in some Resize
modes. (See pages 30 and 31.)
Selectable
items
Useful
Features
• You can set “Overscan” for the following input
signals (Computer, DVI-D Video and DVI-Analog).
—480P, 540P, 576P, 720P, 1035I and 1080I/1080P
• If noise appears at the screen edges when
“Off” is selected, set the function to “On”.
• Also see “About Copyrights” on page 31.
Description
On
All on-screen displays are displayed.
Off
INPUT/VOLUME/AV MUTE/FREEZE/
AUTO SYNC/RESIZE/PICTURE MODE/
ECO+QUIET/MAGNIFY/ “An invalid button
has been pressed.” are not displayed.
43
Adjusting the Projected Image (“SCR - ADJ” Menu)
(Continued)
Menu operation n Page 38
6 Closed Caption
<For Americas only>
8 Reversing/Inverting
Projected Images
Selectable items
Info
• This function is available for NTSC3.58 and 480I
signals.
• This function does not work when the Resize
mode is set to “Border”.
• This function is available in the following cases only:
Resize mode
Normal
Area Zoom
V-Stretch
Stretch
Keystone Correction
Normal image (Projected from
the front of the screen)
Ceiling + Front
Inverted image (Projected from
the front of the screen with an
inverted projector)
Rear
Reversed image (Projected from
the rear of the screen or with a
mirror)
Ceiling + Rear
Reversed and inverted image
(Projected with a mirror)
-40 − +40
-12 − +12
• “Closed Caption” is a system which allows
conversations, narration, and sound effects in TV
programs (Limited regions) and home videos to
be viewed as captions on the screen.
• Not all programs and videos will offer closed
captioning. Please look for the
symbol to
ensure that captions will be shown.
• Two channels are available: CC1 and CC2.
• The Closed Caption letters of this projector are
displayed in black and white.
Selectable items
Description
Off
—
CC1
Closed Caption mode for CH1 data
CC2
Closed Caption mode for CH2 data
See page 19 for details of Projection (PRJ) Mode.
®
TM
9 DLP Link
See the OPERATION MANUAL FOR
STEREOSCOPIC 3D PROJECTION provided
separately.
®
TM
0 DLP Link Invert
See the OPERATION MANUAL FOR
STEREOSCOPIC 3D PROJECTION provided
separately.
Setting the Video Setup
Selectable items
Note
• Closed Caption may malfunction (white blocks,
strange characters, etc.) if signal conditions are
poor or if there are problems at the broadcast
source. This does not necessarily indicate a
problem with the projector.
• If any button is pressed to call up the onscreen display while viewing a Closed Caption
broadcast, the closed captions will disappear.
7 Selecting the Background
Image
Selectable items
Logo
44
Description
Sharp logo screen
Blue
Blue screen
None
—
Description
Front
Description
0 IRE
Sets the black level to 0 IRE.
7.5 IRE
Sets the black level to 7.5 IRE.
Note
• This function is available for the following
signals.
With COMPUTER/COMPONENT or DVI-I input:
- 480I
With S-VIDEO or VIDEO input:
- NTSC3.58
Selecting the On-screen
Display Language
The projector can switch the on-screen
display language among 17 languages.
Adjusting the Projector Function (“PRJ - ADJ” Menu)
Menu operation n Page 38
Pict.
1
2
3
4
5
6
7
8
9
0
SCR
PRJ-ADJ
Net.
Help
Auto Sync
Auto Power Off
Auto Restart
STANDBY Mode
System Sound
Audio Out
On
On
On
Standard
On
VAO
Speaker
Audio Input
RS-232C
Fan Mode
System Lock
Lamp Timer(Life)
On
Audio 1
9600bps
Normal
Disable
0 min 100%
SEL./ADJ.
0 h
ENTER
Selectable
items
On
Description
Auto Sync adjustment will occur when
the projector is turned on or when the
input signals are switched, when
connected to a computer.
Off
Auto Sync adjustment is not
automatically performed.
If the power cord is unplugged from the
outlet or the breaker switch is turned off
when the projector is on, then the
projector automatically turns on when
the power cord is plugged into the AC
outlet or the breaker switch is turned on.
Off
The projector does not turn on
automatically when the power cord is
plugged into the AC outlet or the
breaker switch is turned on.
4 STANDBY Mode
When set to “Eco”, power consumption is
reduced in Standby mode.
Selectable
items
2 Auto Power Off Function
The monitor output and Network
functions are switched off in Standby
mode.
Standard
The monitor output and Network
functions are activated even if the
projector is in Standby mode.
Description
On
When no input signal is detected for
more than 15 minutes, the projector will
automatically enter Standby mode.
Off
The Auto Power Off function will be
disabled.
5 Setting the Confirmation
Sound (System Sound)
Selectable
items
Description
On
A confirmation sound is made when
the projector turns on/off.
Off
No confirmation sound is made.
Useful
Features
Selectable
items
Description
Eco
Note
• Auto Sync adjustment is also performed by
pressing AUTO SYNC.
• The Auto Sync adjustment may take some
time to complete, depending on the image of
the computer connected to the projector.
• When the optimum image cannot be achieved
with Auto Sync adjustment, use manual
adjustments. (See page 51.)
Description
On
END
1 Auto Sync (Auto Sync
Adjustment)
Selectable
items
3 Auto Restart Function
Note
• When the Auto Power Off function is set to
“On”, 5 minutes before the projector enters
Standby mode, the message “Enter STANDBY
mode in X min.” will appear on the screen to
indicate the remaining minutes.
45
Adjusting the Projector Function (“PRJ - ADJ” Menu)
(Continued)
Menu operation n Page 38
6 Audio Output Type Setting
This function determines whether the audio
level output from the AUDIO output (MONITOR
output) terminal is fixed or variable by linking
with VOLUME.
Selectable
items
Description
FAO
Audio output that does not vary in
(Fixed Audio strength with the volume level of the
Output)
source projector.
VAO
(Variable
Audio
Output)
Audio output that varies in strength
with the volume level of the source
projector.
Make sure that both the projector and
computer are set for the same baud rate.
Selectable
items
9600bps
7 Speaker Setting
115200bps
Transmission speed is rapid.
0 Fan Mode Setting
Description
Normal
Suitable for normal environments.
High
Set when using the projector at
altitudes of approximately 1,500 meters
(4,900 feet) or more.
When “Fan Mode” is set to “High”, the fan rotation
speeds up, and the fan noise becomes louder.
System Lock Function
Description
On
The audio signal is output from the
internal speaker.
Off
The audio signal is not output from the
internal speaker.
This function prevents unauthorized use of the
projector. Once this function is activated,
users must enter the correct keycode each
time the projector is turned on. We suggest
you record the keycode in a safe place
where only authorized users have access.
8 Audio Input
This function allows you to select an
appropriate combination of audio input
terminals for each Input mode.
Description
Audio 1
The AUDIO 1 input terminal is used as
an audio input terminal.
Audio 2
The AUDIO 2 input terminal is used as
an audio input terminal.
Info
• If you lose or forget your keycode, contact
your nearest Sharp Authorized Projector
Dealer or Service Center (see page 61). Even
if the product warranty is valid, the keycode
reset will incur a charge.
a Setting/Changing the keycode
1
2
46
Transmission speed is slow.
38400bps
Selectable
items
• When “Audio Out” has been set to “VAO”, first
make sure to lower the volume of the
projector before turning the power on or off
and when switching the input.
Selectable
items
Description
This function changes the fan rotation speed.
Info
Selectable
items
9 Selecting the Transmission
Speed (RS-232C)
Select “System Lock”, then press
ENTER or Q.
Select “Next”, then press ENTER.
• The screen for entering the keycode
appears.
Menu operation n Page 38
3
Press the 4 buttons on the remote
control or on the projector to enter
the preset keycode in “Old Code”.
• When setting the keycode for the first time,
press R on the projector for four times.
PRJ - ADJ
To cancel the keycode that you have
already set
• Press R on the projector for four times in
steps 4 and 5 above.
When the System Lock is set
Setting the System Lock
– – – –
– – – –
– – – –
Old Code
New Code
Reconfirm
Note
• When System Lock is set, the keycode input
screen appears after the power is turned on.
When it appears, enter the right keycode to
start projection.
Input screen for keycode
Note
4
– – – –
System Lock
• If you input a wrong keycode, the cursor
returns to the first point of the “Old Code”.
• The preset keycode is 4 R buttons on
the projector. When you press the R
button four times, the keycord input
screen disappears.
Press the 4 buttons on the remote
control or on the projector to enter
the new keycode in “New Code”.
12 Checking the Lamp
Life Status
You can confirm the cumulative lamp usage
time and the remaining lamp life (percentage).
<PG-D50X3D>
Lamp usage condition
“Life”
Note
• You cannot use the following buttons
for keycode: STANDBY/ON, ON,
STANDBY, ENTER, L-CLICK, RCLICK/RETURN and MENU/HELP
• System Lock function recognizes
each button on the remote control
or on the projector as an individual
button, even if they share the same
button name. If you used the buttons
on the projector in setting your
keycode, the keycode cannot be
canceled with the remote control.
Old Code
New Code
Reconfirm
5
****
– – – –
– – – –
100%
5%
Operated exclusively with Approx.
“Eco +Quiet” set to
2,500
“On”
hours
Approx.
125 hours
Operated exclusively with Approx.
“Eco +Quiet” set to “Off” 2,000
hours
Approx.
100 hours
<PG-D45X3D>
Lamp usage condition
“Life”
Remaining lamp life
100%
5%
Operated exclusively with Approx.
“Eco +Quiet” set to
3,000
“On”
hours
Approx.
150 hours
Operated exclusively with Approx.
“Eco +Quiet” set to “Off” 2,000
hours
Approx.
100 hours
Useful
Features
PRJ - ADJ
Setting the System Lock
Remaining lamp life
Note
Enter the same keycode in “Reconfirm”.
• It is recommended that the lamp be changed
when the remaining lamp life becomes 5%.
• The lamp life may vary depending on the
usage condition.
47
Adjusting the Projector Function (“PRJ - ADJ” Menu)
(Continued)
Keylock Function
Locking the Operation
Buttons on the Projector
Use this function to lock the operation buttons
on the projector.
■ Locking the Operation Buttons
Hold down ENTER on the projector for about
5 seconds while the projector is being turned
on.
On-screen display
• The Keylock function does not affect the
operation with the remote control buttons.
• You cannot use the Keylock function while the
projector is warming up.
■ Taking the Keylock off
Hold down ENTER on the projector for about
5 seconds.
On-screen display
• When the projector is in Standby mode, you can
release the keylock by holding down ENTER
and STANDBY/ON on the projector
simultaneously for about 5 seconds.
Info
• Keylock cannot be set while the projector is:
displaying the “Menu” screens, in Standby
mode, warming up, changing input signals,
operating Auto Sync function, in Freeze mode
or on the “System Lock” screen during
warming up.
48
Setting up the Projector Network Environment (“Network” Menu)
Menu operation n Page 38
Pict.
SCR
PRJ
Network
1
Password
Disable
2
DHCP Client
Off
3
TCP/IP
Help
MAC Address X X : X X : X X : X X : X X : X X
4
Projector
XX-XXXX
SEL./ADJ.
1 Setting a Password
ENTER
2
Enter the password in “Old
Password” using P, R, Q and O,
then press ENTER.
3
Enter the password in “New
Password” using P, R, Q and O,
then press ENTER.
4
Enter the same password again
in “Reconfirm” using P, R, Q and
O, then press ENTER.
If you do not want others to change the setting
for the “Network” menu, set a password.
a Setting a Password
1
Select “Password”, then press
ENTER or Q.
• The screen for entering the password
appears.
Network
Setting the Password
Old Password
New Password
Reconfirm
– – – –
– – – –
– – – –
2
Press P or R to set the first digit
in “New Password”, then press Q.
3
Enter the remaining 3 digits, then
press ENTER.
END
Note
• If you do not need the password protection
for the “Network” menu settings anymore,
press ENTER without entering the new
password in steps 3 and 4.
• To cancel the password settings, press
RETURN.
• To return to the previous digit, press O.
Enter the same password in
“Reconfirm”, then press ENTER.
• The status for “Password” changes to
“Enable”.
If you forget the password
If you forget the password, perform the
following procedure to delete it, then set a
new password.
On the projector, press
Note
• Once the password is set, you must enter the
password to change the “Network” menu
settings.
a Changing the Password
1
Select “Password”, then press
ENTER or Q.
• The screen for entering the password
appears.
.
Useful
Features
4
Note
• If ENTER is held down for more than 5
seconds, the operation buttons on the
projector will be locked. (See page 48.)
• You cannot use the buttons on the
remote control to delete the password.
49
Setting up the Projector Network Environment (“Network” Menu)
(Continued)
Menu operation n Page 38
2 DHCP Client Setting
Connect the LAN cable before turning the
projector on. If not, the DHCP Client function
does not work.
Selectable items
Description
On
Obtains configuration
parameters for TCP/IP network
automatically.
Off
Sets the TCP/IP manually.
Select “On” for “DHCP Client”. “Obtaining IP
Address...” appears, then the menu screen
appears. Confirm the parameters of IP
Address, Subnet Mask and Gateway on the
TCP/IP screen.
If the DHCP server is not available, “Could not
obtain IP Address.” appears.
In this case, set the TCP/IP manually. (See the
item 3.)
3 TCP/IP Setting
Set the TCP/IP manually.
1
Select “Off” for “DHCP Client”,
then press ENTER.
2
Select “TCP/IP”, then press
ENTER.
3
Enter “IP Address” using P, R, Q
and O, then press ENTER.
Network
Selectable items
Factory default setting:
192.168.150.002
Enter an IP address
appropriate for the network.
Subnet Mask
Factory default setting:
255.255.255.000
Set the subnet mask to the
same as that of the computer
and equipment on the
network.
Gateway
Factory default setting:
000. 000. 000. 000
* When not in use, set to “000.
000. 000. 000”.
Note
• Confirm the existing network's segment (IP
address group) to avoid setting an IP address
that duplicates the IP addresses of other
network equipment or computers. If
“192.168.150.002” is not used in a network
with an IP address of “192.168.150.XXX”, you
don't have to change the projector IP address.
• For details about each setting, consult your
network administrator.
4 Confirming the
Projector Information
You can confirm the MAC address and
projector name.
Selectable items
50
1 9 2 . 1 6 8 . 1 5 0 . 0 0 2
2 5 5 . 2 5 5 . 2 5 5 . 0 0 0
0 0 0 . 0 0 0 . 0 0 0 . 0 0 0
4
Enter “Subnet Mask” using P, R,
Q and O, then press ENTER.
5
Enter “Gateway” using P, R, Q
and O, then press ENTER.
Description
MAC Address
The MAC address of the
projector is displayed.
Projector
The projector name is
displayed.
Setting the TCP/IP
IP Address
Subnet Mask
Gateway
Description
IP Address
Note
• For information on how to change the
projector name, see “SETUP MANUAL”
contained in the supplied CD-ROM.
Troubleshooting with the “Help” Menu
This function advises you to solve the problems during usage.
Utilizing the “Help” Menu
Functions
ENTER button
Example: When image flickering appears
Operation to solve image flickering when
projecting the computer RGB signal.
1
Press MENU/HELP.
2
Press O or Q to select “Help”,
then press ENTER.
3
Press P or R to select “Vertical
stripes or flickering image
appears” on Help menu, then
press ENTER.
Pict.
SCR
PRJ
MENU/HELP
button
Net.
Help
Vertical stripes or flickering image appear
There is no picture or audio
Vertical stripes or flickering image appear
Data image is not centered
Color is faded or poor
Picture is dark
The image is distorted
It is difficult to hear audio
Select “Initiate “Auto Sync”
Adjustments”, then press ENTER.
5
If the image is not improved,
select “Adjust horizontal noise”,
then press ENTER.
6
Press O or Q to adjust.
Help
0
Rtn. Menu
END
Note
END
Press ENTER.
Help
Vertical stripes or flickering image appear
Initiate “Auto Sync” Adjustments.
If there is no change after performing "Auto Sync"
adjustments, adjust the following items.
Adjust vertical noise
Adjust horizontal noise
Reset the 2 items above
Return
• You can adjust the items with check marks (✔).
• The items in the “Help” menu change,
depending on the input signal or setting that
you have selected.
• If the problem is not solved, refer to
“Troubleshooting” (see pages 59 and 60).
• When selecting “sRGB” in “Picture Mode”, the
item “Color is faded or poor” is not displayed.
This means you cannot change input signal
types.
Useful
Features
ENTER
4
Phase
SEL./ADJ.
Reset all adjustments to default settings
SEL.
Adjustment buttons
(P/R/O/Q)
Signal Info
1024 768
H
48.3 kHz / V 59.9 Hz
SEL.
ENTER
END
51
Maintenance
Cleaning the projector
■ Ensure that you have unplugged the power
cord before cleaning the projector.
■ The cabinet as well as the operation panel is
made of plastic. Avoid using benzene or
thinner, as these can damage the finish on
the cabinet.
■ Do not use volatile agents such as
insecticides on the projector.
Do not attach rubber or plastic items to the
projector for long periods.
The effects of some of the agents in the
plastic may cause damage to the quality or
finish of the projector.
■ Wipe off dirt gently with a soft flannel cloth.
■ When the dirt is hard to remove, soak a cloth
in a mild detergent diluted with water, wring
the cloth well and then wipe the projector.
Strong cleaning detergents may discolor,
warp or damage the coating on the projector.
Make sure to test on a small, inconspicuous
area on the projector before use.
Cleaning the lens
■ Use a commercially available blower or lens
cleaning paper (for glasses and camera
lenses) for cleaning the lens. Do not use any
liquid type cleaning agents, as they may
wear off the coating film on the surface of the
lens.
■ As the surface of the lens can easily get
damaged, be careful not to scrape or hit the
lens.
nt
rge
ete
dd
Mil
Cleaning the exhaust and intake vents
■ Use a vacuum cleaner to clean dust from the
exhaust vent and the intake vent.
Mild detergent diluted
with water
Info
Wax
52
Thinner
• If you want to clean the air vents during
projector operation, ensure you press
STANDBY/ON on the projector or
STANDBY on the remote control and put the
projector into Standby mode. After the
cooling fan has stopped, clean the vents.
Maintenance Indicators
■ The warning lights (power indicator, lamp indicator and temperature warning indicator) on the
projector indicate problems inside the projector.
■ If a problem occurs, either the temperature warning indicator or the lamp indicator will
illuminate red, and the projector will enter Standby mode. After the projector has entered
Standby mode, follow the procedures given below.
Top View
Power indicator
Lamp indicator
Temperature warning
indicator
About the temperature warning indicator
If the temperature inside the projector increases, due to blockage of the air vents, or the setting
location, the temperature warning indicator will blink. And if the temperature keeps on rising,
“
” will illuminate in the lower left corner of the picture with the temperature warning
indicator blinking. If this state continues, the lamp will turn off, the cooling fan will run and then
the projector will enter Standby mode. When you find the temperature warning indicator
blinking, be sure to perform the measures described on page 54.
About the lamp indicator
■ When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will
be displayed on the screen. When the percentage becomes 0%, it will change to (red), the
lamp will automatically turn off and then the projector will automatically enter Standby mode.
At this time, the lamp indicator will illuminate in red.
■ If you try to turn on the projector a fourth time without replacing the lamp, the
projector will not turn on.
Indicators on the Projector
Power indicator
Lamp indicator
Red on
Green on
Red blinks
Green blinks
Green and orange
blink alternately
Green on
Green blinks
Red on
Normal (Standby)
Normal (Power on)
Abnormal (See page 54.)
Normal (Cooling)
The lens shutter is closed. (See page 29.)
Appendix
Normal
The lamp is warming up.
The lamp is shut down abnormally or requires to be
changed. (See page 54.)
Temperature
Off
Normal
warning indicator Red on/Red blinks The internal temperature is abnormally high. (See page 54.)
53
Maintenance Indicators (Continued)
Maintenance indicator
Normal
Temperature
warning
indicator
Lamp
indicator
Power
indicator
Off
Green on
(Green
blinks
when the
lamp is
warming
up.)
Green on/
Red on
Green
blinks
(Cooling)
Abnormal
Problem
Cause
Possible Solution
• Temperatures
around the projector
are high.
• Blocked air intake
• Use the projector in an
area with a temperature of
lower than 95°F (+35ºC).
• Relocate the projector to
an area with proper
ventilation. (See page 8.)
• Cooling fan
breakdown
• Internal circuit failure
• Clogged air intake
• Take the projector to your
nearest Sharp Authorized
Projector Dealer or Service
Center (see page 61) for
repair.
The lamp does
not illuminate.
• The lamp is shut
down abnormally.
• Disconnect the power cord
from the AC outlet, and
then connect it again.
Time to change
the lamp.
• Carefully replace the lamp.
• Remaining lamp life
becomes 5% or less.
(See page 55.)
• Take the projector to your
• Burnt-out lamp
nearest Sharp Authorized
• Lamp circuit failure
Projector Dealer or Service
Center (see page 61) for
repair.
• Please exercise care when
replacing the lamp.
• Securely install the cover.
Red blinks The internal
(On)/
temperature is
Red on
abnormally high.
(Standby)
Red on
Red on
(Standby)
The lamp does
not illuminate.
Red blinks The power
• The lamp unit cover
indicator blinks in
is open.
red when the
projector is on.
• If the power indicator blinks
in red even when the lamp
unit cover are securely
installed, contact your
nearest Sharp Authorized
Projector Dealer or Service
Center (see page 61) for
advice.
Info
• If the temperature warning indicator illuminates, and the projector enters Standby mode, follow the
possible solutions above and then wait until the projector has cooled down completely before
plugging in the power cord and turning the power back on. (At least 10 minutes.)
• If the power is turned off for a brief moment due to power outage or some other cause while using
the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate
in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace
the power cord in the AC outlet and then turn the power on again.
• The cooling fan keeps the internal temperature of the projector constant and this function is
controlled automatically. The sound of the cooling fan may change during operation because the fan
speed may change and this is not a malfunction.
54
Regarding the Lamp
Lamp
■ It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes
5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life
(percentage) can be checked with the on-screen display. (See page 47.)
■ Purchase a replacement lamp of type AN-D500LP/AN-D400LP from your place of purchase, nearest
Sharp Authorized Projector Dealer or Service Center.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited
warranty. All service of this projector under warranty, including lamp replacement,
must be obtained through a Sharp Authorized Projector Dealer or Service Center.
For the name of the nearest Sharp Authorized Projector Dealer or Service Center,
please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
Hg LAMP CONTAINS MERCURY For State Lamp Disposal
Information
www.lamprecycle.org or 1-800-BE-SHARP
U.S.A ONLY
Caution Concerning the Lamp
■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure
can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches
or deterioration of the lamp due to a lapse of usage time.
The period of time up to failure largely varies depending on the individual lamp and/or the condition and
the frequency of use. It is important to note that failure can often result in the bulb cracking.
■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended
that the lamp be replaced with a new one immediately, even if the lamp appears to be operating
normally.
■ Should the lamp break, there is also a possibility that glass particles may spread inside of the projector.
In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or
Service Center to assure safe operation.
■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of
exposure to the gas, consult a doctor as soon as possible.
Replacing the Lamp
Caution
• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause
burns or injury.
• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully
cool before removing the lamp unit.
■ Carefully change the lamp by following the instructions described in this section. * If you
wish, you may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or
Service Center.
Appendix
* If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Projector
Dealer or Service Center for repair.
55
Regarding the Lamp (Continued)
Removing and Installing the
Lamp Unit
Warning!
• Do not remove the lamp unit from the
projector right after use. The lamp and parts
around the lamp will be very hot and may
cause burns or injury.
Lamp unit
AN-D500LP
(for PG-D50X3D)
AN-D400LP
(for PG-D45X3D)
Optional
accessory
Info
• Do not touch the glass surface of the lamp
unit or the inside of the projector.
• To avoid injury to yourself and damage to the
lamp, make sure you carefully follow the
steps below.
• Do not loosen other screws except for the
lamp unit cover and lamp unit.
1
Press STANDBY/ON on the
projector or STANDBY on the
remote control to put the
projector into Standby mode.
2
Disconnect the power cord.
3
STANDBY/ON button
• Unplug the power cord from the AC
socket.
• Leave the lamp until it has fully cooled
down (about 1 hour).
AC socket
Remove the lamp unit cover.
• Close the lens shutter. Loosen the user
service screw (1) that secures the lamp
unit cover. Remove the lamp unit cover
(2).
2
1
User service screw
(for lamp unit cover)
56
4
Remove the lamp unit.
5
Insert the new lamp unit.
6
Replace the lamp unit cover.
Securing screws
• Loosen the securing screws from the lamp
unit. Hold the lamp unit and pull it in the
direction of the arrow. At this time, keep
the lamp unit horizontal and do not tilt it.
• Press the lamp unit firmly into the lamp unit
compartment. Fasten the securing screws.
• Align the tab on the lamp unit cover
(1) and place it while pressing the cover
(2) to close it. Then tighten the user
service screw (3) to secure the lamp unit
cover.
Info
• If the lamp unit and lamp unit cover
are not correctly installed, the power
will not turn on, even if the power
cord is connected to the projector.
1
2
3
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Info
• Make sure to reset the lamp timer only when
replacing the lamp. If you reset the lamp timer
and continue to use the same lamp, this may
cause the lamp to become damaged or
explode.
1
Connect the power cord and
open the lens shutter fully.
• Plug the power cord into the AC socket of
the projector.
2
Reset the lamp timer.
STANDBY/ON
button
MENU/HELP
button
ENTER button
R button
57
Appendix
• While simultaneously holding down
MENU/HELP, ENTER and R on the
projector, press STANDBY/ON on the
projector.
• “LAMP 0000H” is displayed, indicating
that the lamp timer is reset.
AC socket
Computer Compatibility Chart
Computer
• Multiple signal support
Horizontal Frequency: 15-110 kHz,
Vertical Frequency: 45-85 Hz,
PC/MAC
Mode
Resolution
Pixel Clock: 12-170 MHz
Sync signal: Compatible with TTL level
• Compatible with sync on green signal
Horizontal frequency
[kHz]
Vertical
frequency[Hz]
Analog
Support
60
70
85
60
70
85
50
60
70
72
75
85
50
56
60
70
72
75
85
50
60
70
75
85
60
60
60
75
60
60
60
60
70
75
60
75
60
75
60
60
60
60
67
75
75
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
75
✔
SXGA+
1400 × 1050
MAC 13”
MAC 16”
MAC 19”
WSXGA+
UXGA
VGA
SVGA
XGA
1680 × 1050
1600 × 1200
640 × 480
832 × 624
1024 × 768
27.0
31.5
37.9
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
31.3
35.2
37.9
46.6
48.1
46.9
53.7
40.3
48.4
56.5
60.0
68.7
45.0
47.8
49.7
62.8
47.7
47.8
55.9
55.0
66.2
67.5
60.0
75.0
64.0
80.0
64.0
65.3
65.3
75.0
34.9
49.7
60.2
MAC 21”
SXGA
1152 × 870
68.7
640 × 400
720 × 400
VGA
640 × 480
SVGA
PC
800 × 600
XGA
1024 × 768
WXGA
1280 × 800
WXGA+
1360 × 768
1366 × 768
1440 × 900
1280 × 720
1280 × 768
1152 × 864
SXGA
1280 × 960
1280 × 1024
Digital
Support
Display
✔
✔
✔
✔
Upscale
✔
✔
✔
✔
✔
✔
✔
TRUE
✔
✔*
✔*
✔
✔
*
*
✔
Intelligent
Compression
✔
✔
✔
✔
✔
✔
Upscale
TRUE
Intelligent
Compression
*Switch to Plug-and-Play data. (See page 37.)
Note
• Optimum image quality will be achieved by matching your computer's output resolution to the
resolution that corresponds to “TRUE” in the “Display” column shown above.
• When “Screen resolution” of the computer is different from the resolution displayed on the projected
image, follow the procedures shown below.
– Refer to “Select the resolution” for “Data image is not centered” on the Help menu and select the
same resolution as the resolution in “Screen resolution” of the computer.
– Depending on the computer you are using, the output signal may not be faithful to the “Screen resolution”
adjustment. Check the settings of the computer's signal output. If the settings cannot be changed, it is
recommended that the resolution be set to the one that corresponds to “TRUE” in the “Display” column.
DTV
Horizontal
Signal Frequency
(kHz)
15.7
480I
480P
31.5
540P
33.8
15.6
576I
576P
31.3
720P
37.5
58
Vertical
Frequency (Hz)
60
60
60
50
50
50
Analog
Support
✔
✔
✔
✔
✔
✔
Digital
Support
✔
✔
✔
Horizontal
Signal Frequency
(kHz)
720P
45.0
33.8
1035I
28.1
1080I
33.8
1080I
1080P
56.3
1080P
67.5
Vertical
Frequency (Hz)
60
60
50
60
50
60
Analog
Support
✔
✔
✔
✔
✔
✔
Digital
Support
✔
✔
✔
✔
✔
Troubleshooting
Problem
•
•
•
•
•
•
No picture and no sound •
or projector does not
•
start.
•
•
•
•
•
Check
Projector power cord is not plugged into the wall outlet.
Power to the external connected devices is off.
The lens shutter is closed.
The selected Input mode is wrong.
Cables are incorrectly connected to the projector.
Remote control battery has run out.
External output has not been set when connecting notebook computer.
The lamp unit cover is not installed correctly.
If the connected DVI digital equipment is turned on before the “DVI-D”
input mode is selected on the projector, the image may not be projected
properly or may not be displayed at all. Ensure that the appropriate Input
mode has been selected on the projector before you turn on the
connected equipment.
Cables are incorrectly connected to the projector.
“Bright” is set to minimum position.
Depending on the computer you are using, an image may not be
projected unless the signal output setting of the computer is switched
to the external output. Refer to the computer's operation manual for
how to switch its signal output settings.
Is “On” selected in “DLP ® LinkTM”?
Page
25
–
26, 29
29
21–25
15
21
56, 57
21
21–25
41
–
44
Sound is heard but no
picture appears
(or picture is dark).
• Image adjustments are incorrectly set.
41
• Make adjustments of “Color” and “Tint” in “Picture Mode” and lower the
TM
“BrilliantColor ” value.
(Video Input only)
• Video input system is incorrectly set.
51
Color is faded or poor.
Picture is blurred;
noise appears.
Data image is not
centered.
27
20
–
• “Speaker” is set to “Off”.
46
51
–
21–25
29
Appendix
Picture appears but no
sound is heard.
• Adjust the focus.
• The projection distance exceeds the focus range.
• There is fog on the lens. If the projector is carried from a cold room into a
warm room, or if it is suddenly heated, condensation may form on the surface
of the lens and the image will become blurred. Set up the projector at least
one hour before it is to be used. If condensation should form, remove the
power cord from the wall outlet and wait for it to clear.
(Computer Input only)
• Perform Synchronization Adjustments (“Clock” and “Phase”
Adjustment)
• Noise may appear depending on the computer.
• Cables are incorrectly connected to the projector.
• Volume is set to minimum.
• When the projector is connected to an external device and the volume
is set to minimum, the sound is not output even if you turn up the
volume of the external device.
• Select “Data image is not centered” in the “Help” menu and make the 51
necessary adjustments.
• Depending on the computer you are using, the output resolution signal –
may be different from the one you have set. For details, refer to the
operation manual of the computer.
59
Troubleshooting (Continued)
Problem
Check
• If the picture is normal, the sound is due to cabinet shrinkage caused
An unusual sound is
by room temperature changes. This will not affect operation or
occasionally heard from
performance.
the cabinet.
Maintenance indicator on • See “Maintenance Indicators”.
the projector illuminates
or blinks in red.
• The keylock is set.
The projector cannot
be turned on or put into • If the keylock is set to “ON”, all the buttons are locked.
the Standby mode
using STANDBY/ON on
the projector.
• Change the input signal type setting.
Picture is green on
• When you cannot select an input signal type, select “Color is faded or
COMPUTER
poor” in the “Help” menu, after selecting an item other than “sRGB” in
(Component)/
“Picture Mode”, and then select an input signal type.
DVI (Component).
Page
–
53
48
51
40, 51
Picture is pink
(no green) on
COMPUTER (RGB)/
DVI (RGB).
Picture is too bright and
whitish.
• Image adjustments are incorrectly set.
The cooling fan becomes • When temperature inside the projector increases, the cooling fan runs
faster.
noisy.
•
The lamp indicator is illuminating in red.
The lamp does not light
Replace the lamp.
up even after the
• The lens shutter is closed.
projector turns on.
41
8, 9
52, 53, 54
53, 56, 57
The lamp suddenly turns
off during projection.
The image sometimes
flickers.
The lamp needs much
time to turn on.
• Cables are incorrectly connected to the projector or the connected
equipment works improperly.
• Select “Vertical stripes or flickering image appear” in the “Help” menu
and make the necessary adjustments.
• If this happens frequently, replace the lamp.
• The lamp will eventually need to be changed.
While the remaining lamp life draws to a close, replace the lamp.
21–25
51
56
56
Picture is dark.
The remote control
cannot be used.
• Operate the remote control while pointing it at the projector's remote
control sensor.
• The remote control may be too far away from the projector.
• If direct sunlight or a strong fluorescent lamp is shining on the
projector's remote control sensor, place the projector where it will not
be affected by strong light.
• The batteries may be depleted or inserted incorrectly. Make sure the
batteries are inserted correctly or insert new ones.
15
15
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect
operation or interference. If this should happen, unplug the Unit and plug it in again after more than 5
minutes.
60
For SHARP Assistance
If you encounter any problems during setup or operation of this projector, fi rst
refer to the “Troubleshooting” section on pages 59 and 60. If this operation
manual does not answer your question, please contact the SHARP Service
departments listed below.
U.S.A.
Sharp Electronics Corporation
1-888-GO-SHARP (1-888-467-4277)
lcdsupport@sharpsec.com
http://www.sharpusa.com
Canada
Sharp Electronics of Canada Ltd.
(905) 568-7140
http://www.sharp.ca
Mexico
Sharp Electronics Corporation
Mexico Branch
(525) 716-9000
http://www.sharp.com.mx
Latin America Sharp Electronics Corp. Latin
American Group
(305) 264-2277
www.servicio@sharpsec.com
http://www.siempresharp.com
Benelux
SHARP Electronics Benelux BV
0900-SHARPCE (0900-7427723)
Nederland
9900-0159 Belgium
http://www.sharp.nl
http://www.sharp.be
http://www.sharp.lu
Australia
Sharp Corporation of Australia Pty.
Ltd.
1300-135-022
http://www.sharp.net.au
New Zealand
Sharp Corporation of New Zealand
Phone: (09) 573-0111
Fax: (09) 573-0112
http://www.sharp.net.nz
Singapore
Sharp-Roxy Sales (S) Pte. Ltd.
65-226-6556
ckng@srs.global.sharp.co.jp
http://www.sharp.com.sg
Hong Kong
Sharp-Roxy (HK) Ltd.
(852) 2410-2623
dcmktg@srh.global.sharp.co.jp
http://www.sharp.com.hk
Sharp Electronics (Europe) GMBH
01805-234675
http://www.sharp.de
U.K.
Sharp Electronics (U.K.) Ltd.
08705 274277
http://www.sharp.co.uk/customersupport
Italy
Sharp Electronics (Italy) S.P.A.
(39) 02-89595-1
http://www.sharp.it
Taiwan
Sharp Corporation (Taiwan)
0800-025111
http://www.sharp-scot.com.tw
France
Sharp Electronics France
01 49 90 35 40
hotlineced@sef.sharp-eu.com
http://www.sharp.fr
Malaysia
Sharp-Roxy Sales & Service Co.
(60) 3-5125678
U.A.E.
Spain
Sharp Electronica Espana, S.A.
93 5819700
sharplcd@sees.sharp-eu.com
http://www.sharp.es
Sharp Middle East Fze
971-4-81-5311
helpdesk@smef.global.sharp.co.jp
Thailand
Sharp Thebnakorn Co. Ltd.
02-236-0170
svc@stcl.global.sharp.co.jp
http://www.sharp-th.com
Korea
Sharp Electronics Incorporated of
Korea
(82) 2-3660-2002
lcd@sharp-korea.co.kr
http://www.sharpkorea.co.kr
India
Sharp Business Systems (India)
Limited
(91) 11- 6431313
service@sharp-oa.com
Switzerland
Sharp Electronics (Schweiz) AG
0041 1 846 63 11
cattaneo@sez.sharp-eu.com
http://www.sharp.ch
Sweden
Sharp Electronics ( Nordic ) AB
(46) 8 6343600
vision.support@sen.sharp-eu.com
http://www.sharp.se
Austria
Sharp Electronics (Europe) GMBH
Branch Office Austria
0043 1 727 19 123
pogats@sea.sharp-eu.com
http://www.sharp.at
Appendix
Germany
61
Specifications
Model
Display devices
Resolution
Lens
Input terminals
Output
terminals
Control and
communication
terminals
F number
Zoom
Focus
DVI-I (Compatible with HDCP)
Computer/Component
(mini D-sub 15 pin)
S-Video (mini DIN 4 pin)
Video (RCA)
Audio (ø3.5 mm stereo minijack)
Audio (RCA)
Computer/Component
(mini D-sub 15 pin)
Audio (ø3.5 mm stereo minijack)
LAN (RJ-45)
USB (Type B)
RS-232C (mini D-sub 9 pin)
Speakers
Projection lamp
Rated voltage
Rated frequency
Input current
Power consumption (Standby*)
Operation temperature
Cabinet
Dimensions (main body only) [W × H × D]
Weight (approx.)
AC 100 V
AC 240 V
PG-D50X3D
PG-D45X3D
0.7" DLP® Chip
XGA (1024 × 768)
F 2.5 – 2.7
Manual, ×1.15 (f = 21.0 – 24.2 mm)
Manual
×1
×1
×1
×1
×1
×1 (L/R)
×1
×1 (variable audio output)
×1
×1
×1
5W × 2 (Stereo)
375 W
330 W
AC 100 – 240 V
50/60 Hz
5.1 A
4.5 A
484 W (10.2 W)
429 W (10.2 W)
458 W (10.8 W)
408 W (10.8 W)
41ºF to 95ºF (+5ºC to +35ºC)
Plastic
15 3/4" × 3 15/16" × 13 13/64"
(400 × 100 × 335 mm)
12.8 lbs. (5.8 kg)
*STANDBY Mode: Standard
As a part of policy of continuous improvement, SHARP reserves the right to make design and
specification changes for product improvement without prior notice. The performance specification
figures indicated are nominal values of production units. There may be some deviations from these
values in individual units.
This SHARP projector uses a DLP® chip. This very sophisticated panel contains 786,432
pixels (micromirrors). As with any high technology electronic equipment such as large screen
TVs, video systems and video cameras, there are certain acceptable tolerances that the
equipment must conform to.
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots
on the picture screen. This will not affect the picture quality or the life expectancy of the unit.
62
Dimensions
4 17/32 (115)
3 15/16 (100)
1 43/64
(42.2)
13 13/64 (335)
1/ 4
(6)
Units: inches (mm)
4 17/32
(115)
15 3/4 (400)
M4
M4
M4
2 61/64
(75)
Appendix
1 13/16
(45.75)
15/64 (5.75)
7 5/64
(179.75)
6 49/64 (171.5)
M4
3 33/64
(89)
1 1/ 2
(38)
1/8 (3)
3 23/64
(85)
4 5/8
(116.25)
63
Index
3D MODE button ······················································· 14
Accessories ······························································· 11
AC socket ·································································· 25
Adjustment buttons ··················································· 38
Adjustment foot ························································· 27
AREA ZOOM ····························································· 31
Aspect ratio ······························································· 30
Audio Input ································································ 46
Audio Out ·································································· 46
AUDIO 1, 2 terminal··················································· 23
AUDIO OUT terminal ················································· 23
Auto Power Off ·························································· 45
Auto Restart ······························································ 45
Auto Sync (Auto Sync adjustment) ········· 33, 37, 45, 51
AUTO SYNC button··················································· 33
AV MUTE button ························································ 29
Background ······························································· 44
Batteries ···································································· 15
Blue ··········································································· 41
BORDER ······························································ 30, 31
BREAK TIMER button ··············································· 32
Bright ········································································· 41
BrilliantColorTM ·························································· 41
Carrying handle ························································· 13
Closed Caption·························································· 44
CLR Temp (Color Temperature) ································· 41
C.M.S. ······································································· 41
Color ·········································································· 41
COMPUTER button ··················································· 29
COMPUTER/COMPONENT input terminal ········ 21, 22
Contrast ····································································· 41
DHCP Client ······························································ 50
DLP® LinkTM ······························································· 44
DLP® LinkTM Invert ····················································· 44
DNR ··········································································· 42
DOT BY DOT ····························································· 30
DVI button ································································· 29
DVI-I input terminal·············································· 21, 22
Eco+Quiet···························································· 32, 42
ECO+QUIET button ··················································· 32
ENTER button···························································· 38
Exhaust vent ························································ 12, 52
Fan Mode ·································································· 46
Focus ring·································································· 27
FREEZE button ·························································· 33
FULL ·········································································· 30
HEIGHT ADJUST lever ·············································· 27
Help ··········································································· 51
H-Pos ·································································· 37, 51
Image shift ································································· 43
Input modes ······························································ 29
Intake vent ··························································· 12, 52
Kensington Security Standard connector ················· 13
Keycode ··································································· 46
Keylock ····································································· 48
KEYSTONE button ··················································· 28
Keystone Correction············································ 28, 43
Lamp ········································································· 55
Lamp indicator ·························································· 53
Lamp Timer (Life) ······················································· 47
Lamp unit ·································································· 56
Language (on-screen display language) ··················· 44
64
LAN terminal ······························································ 25
L-CLICK/EFFECT button ····································· 32, 34
Lens shutter························································· 26, 29
MAC Address ···························································· 50
MAGNIFY buttons ····················································· 33
MENU/HELP button ············································ 38, 51
MONITOR OUT terminal············································ 23
MOUSE/Adjustment buttons ······························· 34, 38
Network ····································································· 49
NORMAL ····························································· 30, 31
ON button ·································································· 26
Optional accessories ················································· 11
OSD Display ····························································· 43
Overscan ··································································· 43
PAGE DOWN button·················································· 34
PAGE UP button ························································ 34
Password··································································· 49
PDF············································································ 10
Picture Adjustment ··················································· 40
Picture Mode ······················································· 33, 40
PICTURE MODE button ············································ 33
POINTER button ························································ 32
Power cord ································································ 25
Power indicator ························································· 53
PRJ - ADJ ·································································· 45
PRJ Mode···························································· 19, 44
Progressive ································································ 42
R-CLICK/RETURN button ··································· 34, 38
Red ············································································ 41
Remote control ·························································· 14
Remote control sensor ·············································· 15
Replacing the lamp·············································· 55, 56
Resize ·································································· 30, 43
RESIZE button ··························································· 30
RGB cable ································································· 21
RS-232C terminal ······················································ 24
SCR - ADJ ································································· 43
Screen Size and Projection Distance ························ 20
Security bar ······························································· 13
Sharp ········································································· 41
Speaker ····································································· 46
SPOT button······························································ 32
STANDBY button ······················································· 26
STANDBY Mode ························································ 45
STANDBY/ON button ················································ 26
STRETCH ···························································· 30, 31
Supplied accessories ················································ 11
S-VIDEO button ························································· 29
S-VIDEO terminal ······················································ 22
System Lock······························································ 46
System Sound ··························································· 45
TCP/IP ······································································· 50
Temperature warning indicator ·································· 53
Tint············································································· 41
USB terminal ····························································· 34
VIDEO button ···························································· 29
Video Setup ······························································· 44
VIDEO terminal ·························································· 22
VOL (Volume) buttons················································ 29
V-Pos ··································································· 37, 51
V-STRETCH ······························································· 31
Zoom ring ·································································· 27