RIGOL Probes supported by DS2000A Series

DS2000ASeries
Digital Oscilloscope
Wider vertical range(500uV/div ~ 10V/div), lower noise fl oor,
Better for small signal capturing
Bandwidth 70MHz,100MHz,200MHz,300MHz,standard 50Ω input
Max. Sample Rate 2G Sa/s
Standard Memory Depth up to14Mpts,Optional Memory Depth
up to 56Mpts
Innovative "UltraVision" technology
Waveform capture rate up to 50,000 wfs/s
Up to 256 Levels intensity grading waveform display
Up to 65,000 frames Hardware based Real Time waveform,
Record, Replay & Analysis functions(Std.) A
variety of trigger and serial bus decording
functions(RS232,I2C,SPI,CAN)
Built-in 2 Ch Waveform generator (DS2000A-S)
Complete connectivities: USB Host& Device, LAN(LXI), AUX
Compact size, light weight, easy to use
8 inch TFT (800x480) WVGA
DS2000A Series is the new mainstream digital scope to meet the
customer's applications with its innovative technology, industry
leading specifications, powerful trigger functions and broad
analysis capabilities.
DS2000A Series Digital Oscilloscope
RUN/STOP/SINGLE
Waveform record&replay
Independent control for each channel
Decoding
Product Dimensions: Width X Height X Depth=361.6 mm×179.6 mm×130.8 mm Weight: 3.9 kg ± 0.2 kg(Without Package)
Innovative UltraVision technology
Deeper Memory Depth (Std.14Mpts,Opt.56Mpts) Higher
Waveform Capture Rate (Up to 50,000 wfms/s)
Realtime Waveform Record,Replay & Analysis (Up to 65,000 frames)
Multi-level Intensity Grading Display (Up to 256 Levels)
Models and Key Specifications
Model Number
DS2072A
Analog BW
DS2072A- S
DS2102A
70 MHz
DS2102A- S
DS2202A
100MHz
DS2202A- S
DS2302A
200 MHz
DS2302A- S
300 MHz Channels
2
Max. Sample rate
Max. Memory Depth
Max. Waveform
Capture rate
Real Time waveform
Record,
Replay and Analysis
function
Std. Probes
Built- in 2Ch 25MHz
Source
1 RIGOL
2GSa/s (Single­ channel) 1GSa/s(Dual­ channel
14Mpts std. 56Mpts option
50,000 wfms/s
Up to 65 000 Frames
RP3300A 350MHz BW Passive Probe:2 sets
No
Yes
No
Yes
No
Yes
No
Yes
Wider Vertical range(500uV/div~10V/div),Lower noise
floor, Better for small signal capturing
Full bandwidth,Lower Overshoot, Perfect frequency
response design
UltraVision: Deeper memory(Std.14Mpts,Opt.56Mpts)
UltraVision: Up to 50,000 wfms/s Waveform capture rate
UltraVision:Realtime waveform record,replay,analysis
function (std.)
UltraVision: Deeper Memory with Multi-Level intensity
grading display(Up to 256 levels)
Std. serial bus trigger functions(RS232,I2C,SPI)
Optional Serial bus decoding function with listing display
RIGOL
2
Versatile Trigger Functions(Runt, Nth Edge,Setup/Hold …)
Runt Trigger
Std. Advanced Math Function
Std. Mask Test Function
Built-in 2CH Source(DS2000A-S)
Arb function of the Built-in 2CH Source (DS2000A-S)
Automatic measurements with statistics
Complete Connectivity(USB Host,USB Device,LAN,AUX)
3 RIGOL
RIGOL Probes supported by DS2000A Series:
RIGOL Passive Probes
M odel Number
Tpye
RIGOL Active & Current Probes
Description
1X: DC~7M Hz
High Z 10X:DC~150M Hz
Probe Compatibility All
RIGOL Scopes.
Model Number
Tpye
Current
Probe
BW:DC~300kHz,
Max.DC:± 100A,
AC P- P:200A,AC RMS:70A
Compatibility All RIGOL Scopes.
Current
Probe
BW:DC~1M Hz,
Max.DC:± 70A,
AC P- P:140A,AC RMS:50A
Compatibility
All RIGOL Scopes.
Current
Probe
RP1003C
BW:DC~50M Hz,
Max.AC RMS:30A
AC Peak:50A(Noncontinuous)
Compatibility
All RIGOL Scopes.
Must order RP1000P Power supply.
Current
Probe
RP1004C
BW:DC~100M Hz,
Max. AC RMS:30A,
AC Peak:50A(Noncontinuous)
Compatibility
All RIGOL Scopes.
Must order RP1000P Power supply.
Current
Probe
RP1005C
BW:DC~10M Hz,
Max.150 A rms,
300 A peak (Noncontinuous),
500 A peak (@pulse width <= 30 ms)
Compatibility
All RIGOL Scopes.
Must order RP1000P Power supply.
Power
Supply
Power supply for
RP1003C,RP1004C,RP1005C,
support 4 channels.
RP1001C
RP2200
1X: DC~8M Hz
High Z 10X:DC~350M Hz
Probe Compatibility All
RIGOL Scopes.
RP1002C
RP3300A
DC~500M Hz
High Z
Compatibility All
Probe
RIGOL Scopes.
RP3500A
DC~300M Hz
High CATI 2000V(DC+AC),
Voltage CATII 1500 V(DC+AC)
Probe Compatibility
All RIGOL Scopes.
Description
RP1300H
RP1000P
DC~50M Hz
DC:0~15KV
High
DC,AC:pulse <= 30KVp- p,
Voltage
AC:sine w ave <= 10KVrms
Probe
Compatibility
All RIGOL Scopes.
High
Voltage
Differential
Probe
BW:25M Hz;
Max. Voltage ≤ 1400Vpp
Compatibility
All RIGOL Scopes.
High
Voltage
Differential
Probe
BW:50M Hz;
Max. Voltage ≤ 7000Vpp
Compatibility
All RIGOL Scopes.
High
Voltage
Differential
Probe
BW:100M Hz;
Max. Voltage ≤ 7000Vpp
Compatibility:
All RIGOL scopes
RP1025D
RP1050H
RP1050D
RP1100D
RIGOL
4
Specifications
All the specifications are guaranteed except parameters marked with “Typical” and the oscilloscope needs to operate for more than 30 minutes under the specified
operation temperature.
Sample
Sample Mode
Real Time Sample Rate
Peak Detect
Averaging
High Resolution Memory Depth
Real-time Sample
2 GSa/s (single-channel)
1 GSa/s (dual-channel)
500 ps (single-channel)
1 ns (dual-channel)
After both the channels finish N samples at the same time, N can be 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024,
2048, 4096 or 8192.
12 bits of resolution when ≥5 μs/div @ 1 GSa/s (or ≥10 μs/div @ 500 MSa/s).
single-channel: Auto, 14k pts, 140k pts, 1.4M pts, 14M pts and 56M pts (option) are available
dual-channel: Auto, 7k pts, 70k pts, 700k pts, 7M pts and 28M pts (option) are available
Input
Number of Channels
Input Coupling
Input Impedance Probe Attenuation Coefficient Maximum Input Voltage (1MΩ) Two channels
DC, AC or GND
(1MΩ±1%)||(16 pF±3 pF)
or 50 Ω±1.5%
0.01X to 1000X, in 1­2­5 step
Maximum Input Voltage of the Analog Channel
CAT I 300 Vrms, CAT II 100 Vrms,
Transient Overvoltage 1000 Vpk
with RP2200 10:1 probe: CAT II 300 Vrms with
RP3300A 10:1 probe: CAT II 300 Vrms with
RP3500A 10:1 probe: CAT II 300 Vrms
Horizontal
Timebase Scale
Timebase Accuracy1 Clock Drift Max Delay Range Timebase Mode
Number of XYs
Waveform Capture Rate2
DS2302A: 1 ns/div to 1000 s/div
DS2202A: 2.000 ns/div to 1000 s/div
DS2102A/DS2072A : 5.000 ns/div to 1000 s/div
≤ ± 25 ppm
≤ ± 5 ppm/year
Pretrigger (negative delay): ≥1 screen width
Post-trigger (positive delay): 1 s to 100,000 s
Y-T, X-Y, Roll, Delayed Sweep
1
50,000 wfms/s (dots display)
Vertical
Bandwidth (-3dB)
Single-shot Bandwidth
Vertical Resolution
Vertical Scale Offset Range Bandwidth Limit 1
Low Frequency Response
(AC Coupling, -3dB)
Calculated Rise Time 1
DC Gain Accuracy
5 RIGOL
DS2302A: DC to 300 MHz
DS2202A: DC to 200 MHz
DS2102A: DC to 100 MHz
DS2072A: DC to 70 MHz
DS2302A: DC to 300 MHz
DS2202A: DC to 200 MHz
DS2102A: DC to 100 MHz
DS2072A: DC to 70 MHz
8bit
500 μV/div to 1 V/div (50Ω)
500 μV/div to 10 V/div (1MΩ)
500 μV /div to 50 mV/div: ± 2 V
51 mV/div to 200 mV/div: ± 10 V
205 mV/div to 2 V/div: ± 50 V
2.05 V/div to 10 V/div: ± 100 V
DS2302A/DS2202A : 20 MHz/100 MHz
DS2102A/DS2072A : 20 MHz
≤5 Hz (on BNC)
DS2302A: 1.2ns
DS2202A: 1.8 ns
DS2102A: 3.5 ns
DS2072A: 5 ns
±2% full scale
DC Offset Accuracy
Channel to Channel Isolation
±0.1 div ± 2 mV ± 1% offset value
DC to maximum bandwidth: >40 dB
Trigger
Trigger Level Range
Trigger Mode
Holdoff Range
High Frequency Rejection1
Low Frequency Rejection1
Trigger Sensitivity
Edge Trigger
Edge Type
Pulse Trigger
Pulse Condition Pulse Width Range
Runt Trigger
Pulse Width Condition
Pulse Polarity
Pulse Width Range
Windows Trigger (Option)
Windows Type
Trigger Position
Windows Time
Nth Edge Trigger (Option)
Edge Type
Idle Time
Edge Number
Slope Trigger
Slope Condition Time Setting
Video Trigger (HDTV Option)
Signal Standard
Pattern Trigger
Pattern Setting
Delay Trigger (Option)
Edge Type
Delay Type
Delay Time
TimeOut Trigger (Option)
Edge Type
Timeout time
Duration Trigger (Option)
Pattern
Trigger Condition
Duration Time
Edge Type
Data Type
Setup Time
Hold Time
RS232/UART Trigger
Polarity
Trigger Condition
Baud Rate
Data Bits
I2C Trigger
Trigger Condition
Address Bits
Address Range
Byte Length
Internal
± 5 div from center of the screen
EXT
±4V
Auto, Normal, Single
100 ns to 10 s
75 kHz
75 kHz
1 div (below 10 mV or noise rejection is enabled)
0.3 div (above 10 mV and noise rejection is disabled)
Rising, Falling, Rising&Falling
Positive Pulse Width (greater than, lower than, within specific interval)
Negative Pulse Width (greater than, lower than, within specific interval)
2 ns to 4 s
None, >, <, <>
Positive, Negative
2 ns to 4 s
Rising, Falling, Rising&Falling
Enter, Exit, Time
16 ns to 4 s
Rising, Falling
16 ns to 10 s
1 to 65535
Positive Slope (greater than, lower than, within specific interval)
Negative Slope (greater than, lower than, within specific interval)
2 ns to 4 s
Support standard NTSC, PAL and SECAM broadcasting standards; support 480P, 576P, 720P, 1080P and
1080I HDTV standards
H, L, X, Rising, Falling
Rising, Falling
>, <, <>, ><
2 ns to 4 s
Rising, Falling, Rising&Falling
16 ns to 4 s
H, L, X
>, <, <>
2 ns to 4 s Setup/Hold Trigger
Rising, Falling
H, L
2 ns to 1 s
2 ns to 1 s
Normal, Invert
Start, Error, Check Error, Data
2400 bps, 4800 bps, 9600 bps, 19200 bps, 38400 bps, 57600 bps, 115200 bps, User
5 bit, 6 bit, 7 bit, 8 bit
Start, Restart, Stop, Missing ACK, Address, Data, A&D
7 bit, 8 bit, 10 bit
0 to 127, 0 to 255, 0 to 1023
1 to 5
RIGOL
6
SPI Trigger
Trigger Condition
Timeout Value
Data Bits
Data Line Setting
CAN Trigger
Signal Type
Trigger Condition
Baud
Sample Point
Frame Type
Error Type
USB Trigger (Option)
Signal Speed
Trigger condition
Timeout
100 ns to 1 s
4 bit to 32 bit
H, L, X
Rx, Tx, CAN_H, CAN_L, Differential
SOF, EOF, Frame Type, Frame Error
10 kbps, 20 kbps, 33.3 kbps, 50 kbps, 62.5 kbps, 83.3 kbps, 100 kbps, 125 kbps, 250 kbps, 500 kbps, 800
kbps, 1 Mbps, User
5% to 95%
Data, Remote, Error, OverLoad
Bit Fill, Answer Error, Check Error, Format Error, Random Error
Low Speed, Full Speed
SOP, EOP, RC, Suspend, Exit Suspend
Measure
Cursor
Voltage Deviation between Cursors (△V)
Time Deviation between Cursors (△T)
Reciprocal of △T (Hz) (1/△T)
Track Mode
Voltage and Time Values of the Waveform Point
Auto Mode
Allow to display cursors during auto measurement
Measurements of Maximum, Minimum, Peak-Peak Value, Top Value, Bottom Value, Amplitude, Average,
Mean Square Root, Overshoot, Pre-shoot, Area, Period Area, Frequency, Period, Rise Time, Fall Time,
Positive Pulse Width, Negative Pulse Width, Positive Duty Cycle, Negative Duty Cycle, Delay AàB , Delay
AàB , Phase AàB , Phase AàB
Display 5 measurements at the same time.
Screen or cursor.
Average, Max, Min, Standard Deviation, Number of Measurements
Hardware 6 bits frequency counter
(channels are selectable)
Manual Mode
Auto Measurement
Number of Measurements
Measurement Range
Measurement Statistic
Frequency Counter
Math Operation
Waveform Operation
FFT Window Function
FFT Display
FFT Vertical Scale
Logic Operation
Math Function
Number of Buses for Decoding
Decoding Type
A+B, A-B, A×B, A/B, FFT, Editable Advanced Operation, Logic Operation
Rectangle, Hanning, Blackman, Hamming
Split, Full Screen
Vrms, dB
AND, OR, NOT, XOR
Intg, Diff, Log, Exp, Sqrt, Sine, Cosine, Tangent
2
Parallel (standard), RS232/UART (option), I2C (option) , SPI (option)
Display
Display Type
Display Resolution
Display Color
Persistence Time Display Type
Real-time Clock
8.0 inches (203 mm) TFT LCD display
800 Horizontal ×RGB×480 Vertical Pixel
160,000 Color (TFT)
Min, 50ms, 100ms, 200ms, 500ms, 1 s, 2 s, 5 s, 10 s, 20 s, Infinite
Dots, Vectors
Time and Date (user adjustable)
Signal Source (DS2000AS)
Sample Rate
Vertical Resolution
Frequency
Standard Waveform
Arbitrary Waveform
Sine
7 RIGOL
2
200 MSa/s
14 bits Max.
25 MHz
Sine, Square, Pulse, Ramp, Noise, DC
Sinc, ExpRise, ExpFall, ECG, Gauss, Lorentz, Haversine
Frequency Range
0.1 Hz to 25 MHz
Flatness
±0.5 dB (relative to 1 kHz)
Harmonic Distortion
-40 dBc
Spurious (non-harmonic)
-40 dBc
THD
1%
SNR
40 dB
Square/Pulse
Frequency
Frequency Range
Rise Time/Fall Time
Overshoot
Duty Cycle
Duty Cycle Resolution
Minimum Pulse Width
Pulse Width Resolution
Jitter
Frequency Range
Linearity
Symmetry
Bandwidth
Frequency Range
Frequency Range
Length
Internal Storage Locations
Accuracy
Amplitude
Resolution
Output Range
DC Offset
Resolution Accuracy
Range
Ramp
Noise
Built-in Waveform
Arbitrary Waveform
Resolution Accuracy
0.1 Hz to 15 MHz
<15 ns
<5%
10% to 90%
1% or 10 ns (the larger one)
20ns
10 ns or 5 bits (the larger one)
500 ps
0.1 Hz to 100 kHz
1%
0 to 100%
25 MHz (typical)
0.1 Hz to 1 MHz
0.1 Hz to 10 MHz
2 to 16 kpts
10
100 ppm (<10 kHz)
50 ppm (>10 kHz)
0.1 Hz or 4 bits (the larger one)
20 mVpp to 5 Vpp, HighZ
10 mVpp to 2.5 Vpp, 50 Ω
100 μV or 3 bits (the larger one)
2% (1 kHz)
±2.5 V, HighZ
±1.25 V, 50 Ω
100 μV or 3 bits (the larger one)
±2% of Offset setting
Interface
Standard Ports
Printer Compatibility
USB HOST (support USB-GPIB), USB DEVICE, LAN, Aux Output (TrigOut/PassFail)
PictBridge
General Specifications
Probe Compensation Output
Output Voltage1
Frequency1
Power
Power Voltage
Power
Fuse
Environment
Temperature Range
Cooling Method
Humidity Range
Altitude
About 3 V, peak-peak
1 kHz
100 to 240 V, 45 to 440 Hz
Maximum 50 W
2 A, T Degree, 250 V
Operating: 0℃ to +50℃
Non-operating: -20℃ to +70℃
fan cooling
0℃ to +30℃ : ≤95% Relative Humidity
+30℃ to +40℃ : ≤75% Relative Humidity
+40℃ to +50℃ : ≤45% Relative Humidity
Operating: under 3,000 meters
Non-operating: under 15,000 meters
Mechanical Specifications
Size3
Weigt4
Width×Height×Depth = 361.6 mm× 179.6 mm×130.8 mm
Package Excluded
3.9 kg ± 0.2 kg
Package Included
4.5 kg ± 0.5 kg
Calibration Interval
The recommended calibration interval is one year.
Regulatory Information
Electromagnetic Compatibility
2004/108/EC
Execution standard EN 61326-1:2006 EN 61326-2-1:2006
Safety
UL 61010-1:2004; CAN/CSA-C22.2 NO. 61010-1-2004;
EN 61010-1:2001; IEC 61010-1:2001
Note: 1
2
3
4 Typical.
Maximum value with 20 ns, single-channel, dots display and auto memory depth.
Supporting legs and handle folded, knob height included.
Standard configuration.
RIGOL
8
Ordering Information
Description
70MHz,2-channel
70MHz,2-channel + 2-channel Signal Source
100MHz,2-channel
100MHz,2-channel + 2-channel Signal Source
200MHz,2-channel
200MHz,2-channel + 2-channel Signal Source
300MHz,2-channel
300MHz,2-channel + 2-channel Signal Source
Power Cord conforming to the standard of the country
USB Data Cable
2 Passive Probes (350 MHz)
Quick Guide
Resource CD (User’s Guide and Application Software)
Rack Mount Kit
56Mpts(single channel)/28Mpts(dual channel)
Model
Standard Accessories
Optional Accessories
Deep Memory Option
Advanced trigger functions
Windows, Nth Edge,HDTV,Delay, Time Out,
Duration, USB
RS232,I2C,SPI Decoding Kit
CAN Analysis kit(Trigger+Decoding)
Decoding Options
Order Number
DS2072A
DS2072A-S
DS2102A
DS2102A-S
DS2202A
DS2202A-S
DS2302A
DS2302A-S
CB-USBA-USBB-FF-150
RP3300A
RM-DS2000A
MEM-DS2000A
AT-DS2000A
SD-DS2000A
CAN-DS2000A
Warranty
Three- year warrant y,excluding probes and accessories.
www.RIGOL-UK.co.uk
Headquarter
USA
Europe
RIGOL TECHNOLOGIES, INC.
No.156,Cai He Village,
Sha He Town,
Chang Ping District, Beijing,
102206 P.R.China
Tel:+86-10-80706688 Fax:+8610-80705070
Email: info@rigol.com
RIGOL TECHNOLOGIES
USA,INC.
7401 First Place,Suite N
Oakwood Village
OH 44146,USA
Tel/Fax: 440-232-4488
Toll free: 877-4-RIGOL-1
Email: info@rigol.com
RIGOL TECHNOLOGIES EU,
GmbH
Lindbergh str. 4
82178 Puchheim, Germany Tel:
+49(0)89-8941895-0
Email: infoeurope@
rigoltech.com
RIGOL® is the registered trademark of RIGOL Technologies, Inc. Product information in this document subject to update without notice. For
the latest information about RIGOL's products, applications and services, please contact local RIGOL offi ce or access RIGOL offi cial website:
www.rigol.com
October,2013