Instruction Manual
Modero S Series
Touch Panels
MST-1001/MSD-1001-L - 10.1" Modero S Series Touch Panels
MST-701/MSD-701-L - 7" Modero S Series Touch Panels
MST-431/MSD-431-L - 4.3" Modero S Series Touch Panels
Modero S Series Touch Panels
Last Revised: 10/08/2014
AMX Limited Warranty and Disclaimer
This Limited Warranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Partner which
include AMX Dealers, Distributors, VIP’s or other AMX authorized entity.
AMX warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of
purchase, with the following exceptions:
•
Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components are warranted for a period of one (1) year.
•
Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year.
•
AMX lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long
as the AMX lighting products are under warranty. AMX also guarantees the control of dimmable loads that are properly connected to our lighting products. The dimming performance or quality there of is not guaranteed, impart due to the random combinations of dimmers, lamps and ballasts or transformers.
•
AMX software is warranted for a period of ninety (90) days.
•
Batteries and incandescent lamps are not covered under the warranty.
•
AMX AutoPatch Epica, Modula, Modula Series4, Modula CatPro Series and 8Y-3000 product models will be free of defects in
materials and manufacture at the time of sale and will remain in good working order for a period of three (3) years following the
date of the original sales invoice from AMX. The three-year warranty period will be extended to the life of the product (Limited
Lifetime Warranty) if the warranty card is filled out by the dealer and/or end user and returned to AMX so that AMX receives it
within thirty (30) days of the installation of equipment but no later than six (6) months from original AMX sales invoice date. The
life of the product extends until five (5) years after AMX ceases manufacturing the product model. The Limited Lifetime Warranty
applies to products in their original installation only. If a product is moved to a different installation, the Limited Lifetime Warranty
will no longer apply, and the product warranty will instead be the three (3) year Limited Warranty.
All products returned to AMX require a Return Material Authorization (RMA) number. The RMA number is obtained from the AMX
RMA Department. The RMA number must be clearly marked on the outside of each box. The RMA is valid for a 30-day period. After
the 30-day period the RMA will be cancelled. Any shipments received not consistent with the RMA, or after the RMA is cancelled, will
be refused. AMX is not responsible for products returned without a valid RMA number.
AMX is not liable for any damages caused by its products or for the failure of its products to perform. This includes any lost profits, lost
savings, incidental damages, or consequential damages. AMX is not liable for any claim made by a third party or by an AMX Authorized Partner for a third party.
This Limited Warranty does not apply to (a) any AMX product that has been modified, altered or repaired by an unauthorized agent or
improperly transported, stored, installed, used, or maintained; (b) damage caused by acts of nature, including flood, erosion, or earthquake; (c) damage caused by a sustained low or high voltage situation or by a low or high voltage disturbance, including brownouts,
sags, spikes, or power outages; or (d) damage caused by war, vandalism, theft, depletion, or obsolescence.
This limitation of liability applies whether damages are sought, or a claim is made, under this warranty or as a tort claim (including
negligence and strict product liability), a contract claim, or any other claim. This limitation of liability cannot be waived or amended by
any person. This limitation of liability will be effective even if AMX or an authorized representative of AMX has been advised of the
possibility of any such damages. This limitation of liability, however, will not apply to claims for personal injury.
Some states do not allow a limitation of how long an implied warranty last. Some states do not allow the limitation or exclusion of incidental or consequential damages for consumer products. In such states, the limitation or exclusion of the Limited Warranty may not
apply. This Limited Warranty gives the owner specific legal rights. The owner may also have other rights that vary from state to state.
The owner is advised to consult applicable state laws for full determination of rights.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX MAKES NO OTHER WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX
EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT
MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. EXCEPT AS OTHERWISE LIMITED
BY APPLICABLE LAW, AMX RESERVES THE RIGHT TO MODIFY OR DISCONTINUE DESIGNS, SPECIFICATIONS, WARRANTIES, PRICES, AND POLICIES WITHOUT NOTICE.
Table of Contents
Table of Contents
Modero S Series G4 Touch Panels ......................................................................1
Overview .................................................................................................................. 1
Features .......................................................................................................................... 1
Sleep Button ............................................................................................................. 2
Configuration and Programming .............................................................................. 2
Accessing the Settings Menu .......................................................................................... 2
Using the Settings Pages................................................................................................. 2
Bluetooth Support .................................................................................................... 3
Picture View.............................................................................................................. 3
Starting Picture View....................................................................................................... 3
Preview Mode and Normal Mode ................................................................................... 4
Picture View Send Command (^PIC)................................................................................ 4
Panel Calibration....................................................................................................... 4
Testing the Panel Calibration .......................................................................................... 4
Cleaning the Touch Overlay and Case ...................................................................... 5
MST/D-1001 - 10.1" S Series Touch Panels ........................................................7
MST-1001 (Tabletop) ............................................................................................... 7
MST-1001 Specifications ................................................................................................. 7
MSD-1001-L (Wall Mount-Landscape) ...................................................................... 9
MSD-1001-L Specifications ............................................................................................. 9
Touch Panel Aspect Ratio ......................................................................................................... 11
MST/D-701 - 7" S Series Touch Panels .............................................................13
MST-701 (Tabletop) ............................................................................................... 13
MST-701 Specifications ................................................................................................. 13
MSD-701-L (Landscape Wall Mount) ....................................................................... 15
MSD-701-L Specifications ............................................................................................. 15
Touch Panel Aspect Ratio ......................................................................................................... 17
MST/D-431 - 4.3" S Series Touch Panels ..........................................................19
MST-431 (Tabletop) ............................................................................................... 19
MST-431 Specifications ................................................................................................ 19
MSD-431-L (Wall Mount - Landscape) ..................................................................... 21
MSD-431-L Specifications ............................................................................................. 21
Touch Panel Aspect Ratio ......................................................................................................... 23
Installing Tabletop (MXT) Panels ......................................................................25
MST-1001/701/431 ................................................................................................. 25
Connector Locations ................................................................................................................. 25
Power via Power Over Ethernet ............................................................................................... 25
Modero S Series G4 Touch Panels Instruction Manual
i
Table of Contents
Installing Wall-Mount (MXD) Panels ..................................................................27
A Note About Wall and Rack Installation................................................................ 27
Installation Recommendations....................................................................................... 28
MSD-1001/701/431-L ............................................................................................. 28
Removing the Backbox ........................................................................................... 29
Detaching the MSD-1001-L Backbox ........................................................................................ 29
Installation .............................................................................................................. 30
Installing the S Series Panel into a Wall......................................................................... 31
MXD-1001-L Dimensions ....................................................................................................... 31
MXD-701-L Dimensions ........................................................................................................... 32
MXD-431-L Dimensions ............................................................................................................ 33
Installing the Backbox ................................................................................................... 33
Removing The Touch Panel From the Backbox After Wall Installation .......................... 38
Upgrading Firmware .........................................................................................39
Overview ................................................................................................................ 39
Downloading Firmware Updates From www.amx.com ........................................... 39
Upgrading Firmware via USB Flash Drive ............................................................... 39
Load the Firmware on a USB Flash Drive ...................................................................... 39
Transfer the Firmware File From the Flash Drive to the Touch Panel............................ 40
Upgrading from Previous Firmware ........................................................................ 41
Returning to Factory Default Firmware .................................................................. 41
Upgrading Firmware via NetLinx Studio................................................................. 41
Transferring the KIT File via NetLinx Studio.................................................................. 42
Troubleshooting ...............................................................................................43
Overview ................................................................................................................ 43
Panel Doesn’t Respond to Touches ............................................................................... 43
Panel Isn’t Appearing in the Online Tree Tab................................................................ 43
Can’t Connect to a NetLinx Master ............................................................................... 43
Only One Modero S Series Panel Indicated in My System ............................................ 43
ii
Modero S Series G4 Touch Panels Instruction Manual
Modero S Series G4 Touch Panels
Modero S Series G4 Touch Panels
Overview
The Modero S Series is a beautiful touch panel family sophisticated enough for room control yet priced right for the
most cost sensitive installations. The Modero S Series panels include VoIP, brilliant 24-bit color depth, PoE connectivity,
USB and streaming video.
Features
Architectural Design Consistency – Install both Modero S and Modero X touch panels throughout a facility
for consistent style on any budget
Secure Table Mounting Option – Our beautifully styled secure mounting plate attaches to the Modero S
tabletop touch panels and secures with under-table tamper resistant bolts making it virtually theft proof; if it’s
not possible or desirable to mount the touch panel to the table the secure plate can also be used in conjunction
with a Kensington Lock, or mount it and use the lock together for extra security
Powerful Graphics – Powered by G4, the Modero S Series features streaming video and brilliant 24-bit color
depth
FIG. 1 Modero S Series Touch Panels
The Modero S-Series G4 Touch Panels covered in this manual include:
Modero S-Series G4 Touch Panels
Name
FG#
Description
Page Ref
MST-1001
FG2265-05
10.1" Modero S Series Tabletop Touch Panel
page 7
MSD-1001-L
FG2265-01
10.1" Modero S Series Landscape Wall Mount Touch Panel
page 9
MST-701
FG2265-06
7" Modero S Series Tabletop Touch Panel
page 13
MSD-701-L
FG2265-02
7" Modero S Series Landscape Wall Mount Touch Panel
page 15
MST-431
FG2265-07
4.3" Modero S Series Tabletop Touch Panel
page 19
MSD-431-L
FG2265-03
4.3" Modero S Series Landscape Wall Mount Touch Panel
page 21
Modero S Series G4 Touch Panels Instruction Manual
1
Modero S Series G4 Touch Panels
Sleep Button
S Series touch panels are operated using an integral touchscreen, as well as the Sleep button. The Sleep button is located
on the top center edge of the panel (see FIG. 2).
Sleep button
(on top panel)
Sleep button
(on top panel)
FIG. 2 Sleep Button location - Tabletop and Wall Mount
If the device has gone into its Sleep Mode, touching the touchscreen or pressing the Sleep button will reactivate it.
Press and hold the Sleep button to access the Settings menu.
Configuration and Programming
S Series touch panels are equipped with a Settings menu that provides the ability to configure various features on the
panels. To access the Settings menu, press and hold the Sleep button, and select Settings. This opens the main Settings
menu
Unlike previous G4 touch panels, Modero S Series touch panels do not have
separate Setup and Protected Setup pages. All touch panel settings and functionality
are now controlled through one Settings menu. The Connection & Networks and
Configuration sections are accessible with the correct password.
Accessing the Settings Menu
1. To access the Settings menu, press and hold the Sleep button on the touch panel for 3 seconds.
 Alternately, some installation circumstances may require disabling Settings page access through the Sleep
button. In this case, you may access Settings pages during a bootup of the panel.
As the panel boots up, watch for a series of indicator dots to appear on the splash screen (FIG. 3).
2. To access the Settings menu, press the bottom right corner of the touchscreen within the first three seconds of these
dots appearing on the screen.
FIG. 3 Indicator dots on the Modero X Series splash screen
Using the Settings Pages
When opened, the Settings menu appears in the center of the panel display. Note that many of the pages may be longer
than they initially appear. Scroll down to reach all functions on a given page.
Information on the Settings menu, panel configuration, and programming is included in the Modero X Series G4
Programming Guide, available at www.amx.com.
Programming Modero S Series touch panels require the use of the latest versions of
NetLinx Studio and TPDesign4, both available to download at www.amx.com.
2
Modero S Series G4 Touch Panels Instruction Manual
Modero S Series G4 Touch Panels
Bluetooth Support
S Series touch panels allow the use of Bluetooth keyboard and mouse combinations, using HID Profile v1.1.
Using a keyboard and mouse with the device requires use of the MXA-BT Bluetooth USB Adapter (FG5968-19).
Picture View
By connecting a USB drive via one of the device’s USB ports, Picture View allows the S Series panel to access JPEG
images on that drive and display them on the touchscreen. Individual images may be accessed at any time, or the entire
collection may be displayed for predetermined times.
Picture View may be stopped at any time by removing the USB drive, and the panel will return to its default display
page.
The maximum source resolution for Picture View is 1920x1920 pixels.The maximum
displayed resolution is the same as the screen resolution.
Starting Picture View
1. Connect a USB drive to the device. Picture View will automatically recognize all available images on the drive and
start displaying them on the touchscreen.
2. When the images begin to display, touch any place on the touchscreen to open the configuration popup menu
(FIG. 4).
If no selection is made, this menu will remain in place for 15 seconds and then disappear.
It may be accessed again by touching anywhere on the touchscreen.
Stop
Pause/Resume
Random / A-Z
Previous image
Counter
Timer
Next image
FIG. 4 Picture View Configuration Popup Menu
3. On the leftmost amber button, select between Rand (images display at random) and A-Z (images display in
alphabetical order based on the name of the file).
4. The four gray buttons allow scrolling through saved images and the rate of display:
The Previous Image Saved button returns the display to the first image uploaded by Page View.
The Stop button stops Page View and returns to the default panel page.
The Pause/Resume button allows the display to stop on one particular image. Press it again to resume the
display procession.
The Next Image Saved button returns the display to the last image uploaded by Page View. If the panel has
not accessed all of the images available on a USB drive, Page View will display the last one uploaded to date.
Modero S Series G4 Touch Panels Instruction Manual
3
Modero S Series G4 Touch Panels
5. On the rightmost red button, select the number of seconds a selected image will be displayed in Picture View. This
may be selected between 5, 10, 15, 30, and 60 seconds.
6. The counter beneath the buttons displays the number of images currently uploaded by the MST-1001 versus the
number detected on the USB drive.
Preview Mode and Normal Mode
Picture View has two modes: Preview Mode and Normal Mode.
Preview Mode allows the user to configure Picture View. Once a USB drive containing images is inserted into the panel,
the images will begin to display. Touching any place on the display will result in the configuration popup to slide from
the bottom of the display.
Picture View goes into its Normal Mode when the MST-1001 goes into idle timeout while connected to a USB drive.
Normal Mode displays images until the touchscreen is touched, or some other wakeup event is detected. When the
device goes back into timeout, Normal Mode will return to displaying images until the USB drive is removed from the
device.
Picture View Send Command (^PIC)
The ^PIC Send Command stops either mode of Picture View, or starts Preview Mode. For more information, please
refer to the Modero S Series Programming Guide, available at www.amx.com.
All images must be in JPEG format. PNG and other image formats cannot be viewed
through Picture View.
Panel Calibration
It is recommended that the panel is calibrated before its initial use and after completing a firmware download. Panel
calibration is performed via the Calibrate page. The Calibrate page is accessed in one of two ways:
By holding the Sleep button for ~6 seconds
Going to Settings > Display > Calibration
1. Press and hold the Sleep button for 6 seconds (passing-over the Setup page) to access the Calibrate page (FIG. 5):
The request to touch the crosshairs
is the first on-screen message
Calibration successful is the second
on-screen message that appears
after the calibration process is
completed
Calibration Successful
On-screen crosshairs used for
calibration of the touch device
FIG. 5 Touch Panel Calibration Screens
2. Press the crosshairs to set the calibration points on the screen.
3. After the "Calibration Successful." message appears, press anywhere on the screen to continue and return to the
Setup page.
Testing the Panel Calibration
1. Press and hold the on-screen Calibration button for 6 seconds to enter the Calibrate page.
2. Press anywhere on this page to confirm the on-screen crosshairs match your touch points.
3. If the crosshairs do not appear directly below your LCD touch points, press the Back button and recalibrate the
panel using the above steps.
4. Exit the Calibrate page by pressing the Back button to return to the Protected Setup page.
4
Modero S Series G4 Touch Panels Instruction Manual
Modero S Series G4 Touch Panels
If the calibration was improperly set and you cannot return to the Calibrate
page (through the panel’s firmware); this firmware page can be accessed via G4
WebControl by navigating to the Protected Setup page and pressing the Calibrate
button through the VNC window.
This action causes the panel to go to the Calibrate page seen above, where
recalibration of the actual touch panel can be performed again using the above
procedures.
A mouse can be plugged into the USB port (on panels that have access to it) and
used to navigate back to the Calibration page. The process of pushing the button
could also be repeated as necessary.
Cleaning the Touch Overlay and Case
When cleaning the device, do not directly spray the device with cleaning fluid. Instead, spray the cloth and
then apply the cloth to the touch screen.
Do NOT use abrasives of any type to clean the device, as abrasives may permanently damage or remove the
device’s finish.
Modero S Series G4 Touch Panels Instruction Manual
5
Modero S Series G4 Touch Panels
6
Modero S Series G4 Touch Panels Instruction Manual
MST/D-1001 - 10.1" S Series Touch Panels
MST/D-1001 - 10.1" S Series Touch Panels
MST-1001 (Tabletop)
Microphone
Sleep Button
USB Port
FIG. 6 MST-1001
MST-1001 Specifications
MST-1001 Specifications
DIMENSIONS (HWD)
6 13/16" x 10 1/16" x 2" (174mm x 255mm x 51mm)
WEIGHT
2.6 lbs (1.179 Kg)
POWER CONSUMPTION
•
•
•
•
•
EXTERNAL POWER
SUPPLY REQUIRED
Optimal performance requires use of one of the following AMX PoE power supplies (not
included):
Full-On: 14 W (max)
Typical: 7.5 W
Standby: 4.5 W
Shutdown: 0.7 W
Start-Up Inrush Current: Not applicable due to PoE standard
• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant (FG423-83)
• NXA-ENET8-2POE, Gigabit PoE Ethernet Switch (FG2178-63)
CERTIFICATIONS
• FCC Part 15 Class B
• CE EN 55022
• CE EN 55024
• CE EN 60950-1
• IEC 60950-1
• C-Tick CISPR 22 Class B
• IC CISPR 22 Class B
• UL 60950-1
• VCCI CISPR 22 Class B
• RoHS
• WEEE
Modero S Series G4 Touch Panels Instruction Manual
7
MST/D-1001 - 10.1" S Series Touch Panels
MST-1001 Specifications (Cont.)
TOUCH SCREEN DISPLAY
• Display Type: TFT Active Matrix Color LCD
• Display Size (WH): Landscape: 9.1" x 5.9" (230 mm x 149 mm), 10.8" (274 mm)
diagonal
• Viewable Area (WH): Landscape: 8.5" x 5.4" (217 mm x 136 mm ), 10.0" (256 mm)
diagonal
• Resolution: Landscape: 1280x800
• Aspect Ratio: Landscape: 16:9
• Brightness: 350 cd/m2
• Contrast Ratio: 800:1
• Color Depth: 16.7M colors
• Illumination: LED
• Touch Overlay: Resistive
VIEWING ANGLE
85°/85°/85°/85° (Up/Down/Left/Right)
MEMORY
• SDRAM: 512 MB
• Flash: 4 GB
• Maximum Project Size: 2.4 GB flash available to user
COMMUNICATIONS
• Ethernet: 10/100 port, RJ-45 connector. Supported IP and IP-based protocols: UCP,
TCP, ICMP, ICSP, IGMP, DHCP, Telnet, FTP, DNS, RFB (for VNC), HTTP
• USB: (1) USB host 2.0, Type A port: Firmware upgrade, touch panel file transfer, JPEG
image viewer, HID Peripherals
• Bluetooth®: Mouse/Keyboard: HID Profile v1.1, requires MXA-BT, Bluetooth USB
Adapter for Modero X/S Series Touch Panels (FG5968-19) and MXA-HST, Bluetooth
Handset for Modero X/S Touch Panels (FG5968-17)
VIDEO
• Supported Video Codecs:
MPEG2-TS: MPEG-2 Main Profile@High Level up to 720p at 25 fps (decode)
MPEG-2-TS: H.264 High Profile@Layer 4, AAC-LC up to 720p at 25 fps (decode)
MJPEG up to 720p at 25 fps (decode)
• Supported Video Transport Streams: MPEG-TS for MPEG2 and H.264; HTTP for
MJPEG
• Max Number of Active Video Streams: One decode
AUDIO
• Microphone: -42 dB ±3 dB sensitivity FET microphone
• Speakers: 4 ohm, 1.5 Watt, 500 Hz cutoff frequency
• Supported Audio Codecs:
MP2 Layer I and II, MP3 (8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32
kHz, 44.1 kHz, 48 kHz)
AAC-LC (8 kHz, 96 kHz)
G.711 with µLaw (VoIP encode/decode at 8 kHz)
• File Formats: WAV, MP3 (as part of touch panel file only - no USB storage)
• Intercom: Full Duplex VoIP, SIP v2.0 (supported with AMX-CSG)
GRAPHICS ENGINE
AMX G4: AMX's exclusive, powerful G4 graphics engine – the driving force behind the
advanced graphics and image processing capability on a variety of AMX Touch Panels
and other devices (see TPD4 Operations Guide for more information)
EMBEDDED APPLICATIONS • Remote Management: VNC Server, G4 Web Control
• Panel-to-Panel Conferencing: Receives audio and video and returns audio for panelto-panel communication
• Audio Conferencing: Audio (Full Duplex Intercom)
8
FRONT PANEL
COMPONENTS
Sleep Button: Sleep button to activate sleep mode and powering off. Also provides
access to setup pages (can be disabled)
CONNECTIONS
• Ethernet: 10/100 port, RJ-45 connector
• USB: (1) USB host 2.0, Type A port
• Power: PoE (Power over Ethernet), 802.3af, class 3
Modero S Series G4 Touch Panels Instruction Manual
MST/D-1001 - 10.1" S Series Touch Panels
MST-1001 Specifications (Cont.)
ENVIRONMENTAL
•
•
•
•
•
Temperature (Operating): 32° F to 104° F (0° C to 40° C)
Temperature (Storage): 4° F to 140° F (-20° C to 60° C)
Humidity (Operating): 20% to 85% RH
Humidity (Storage): 5% to 85% RH
Power ("Heat") Dissipation:
On: 109.2 BTU/hr
Standby: 10.6 BTU/hr
INCLUDED ACCESSORIES
• MXA-USB-C, USB Port Cover Kit, Modero X Series Touch Panel (FG5968-18)
• Cat5e Ethernet Cable, Flat Black (ECA2265-10)
• UTP CAT.5E Snap In Coupler, Black (64-5968-01)
OPTIONAL ACCESSORIES
• MSA-STMK-10, Secure Table Mount Kit for Modero S Series Touch Panel, 10"
(FG2265-16)
• MXA-MP, Modero X/S Series Multi Preview (FG5968-20)
• MXA-MPL, Modero X/S Series Multi Preview Live (FG5968-10)
• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant (FG423-83)
• NXA-ENET8-2POE, Gigabit Ethernet Switch (FG2178-63)
• MXA-BT, Bluetooth USB Adapter for Modero X/S Series Touch Panels (FG5968-19)
• MXA-HST, Bluetooth Handset for Modero X/S Series Touch Panels (FG5968-17)
• HPG-10-10K, 3/4" Mini-Grommet, 10-Pack (FG570-01-10K)
• MXA-CLK, Modero X/S Series Screen Cleaning Kit (FG5968-16)
• MXA-USB-C, USB Port Covers for the Modero X/S Series Touch Panels (FG5968-18)
MSD-1001-L (Wall Mount-Landscape)
Sleep Button
Microphone
Backbox
Left
LED
Right
LED
(side view)
FIG. 7 MSD-1001-L
MSD-1001-L Specifications
MSD-1001-L Specifications
DIMENSIONS (HWD)
6 3/16" x 10 3/8" x 2 5/16" (157 mm x 264 mm x 58 mm)
WEIGHT
• 1.95 lbs (.885 Kg), with Backbox
• 1.5 lbs (.680 Kg), without Backbox
POWER CONSUMPTION
•
•
•
•
•
Modero S Series G4 Touch Panels Instruction Manual
Full-On: 14 W
Typical: 7.5 W
Standby: 4.7 W
Shutdown: 0.8 W
Start-Up Inrush Current: Not applicable due to PoE standard
9
MST/D-1001 - 10.1" S Series Touch Panels
MSD-1001-L Specifications (Cont.)
EXTERNAL POWER
SUPPLY REQUIRED
Optimal performance requires use of one of the following AMX PoE power supplies (not
included):
• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant (FG423-83)
• NXA-ENET8-2POE, Gigabit PoE Ethernet Switch (FG2178-63)
CERTIFICATIONS
• FCC Part 15 Class B
• CE EN 55022
• CE EN 55024
• CE EN 60950-1
• IEC 60950-1
• C-Tick CISPR 22 Class B
• IC CISPR 22 Class B
• UL 60950-1
• VCCI CISPR 22 Class B
• RoHS
• WEEE
TOUCH SCREEN DISPLAY
• Display Type: TFT Active Matrix Color LCD
• Display Size (WH): Landscape: 9.1" x 5.9" (230mm x 149mm), 10.8" (274mm) diagonal
• Viewable Area (WH): Landscape: 8.5" x 5.4" (217mm x 136mm ), 10.0" (256mm)
diagonal
• Resolution: Landscape: 1280x800
• Aspect Ratio: Landscape: 16:9
• Brightness: 350 cd/m2
• Contrast Ratio: 800:1
• Color Depth: 16.7M colors
• Illumination: LED
• Touch Overlay: Resistive
VIEWING ANGLE
85°/85°/85°/85° (Up/Down/Left/Right)
MEMORY
• SDRAM: 512 MB
• Flash: 4 GB
• Maximum Project Size: 2.4 GB flash available to user
COMMUNICATIONS
• Ethernet: 10/100 port, RJ-45 connector. Supported IP and IP-based protocols: UCP,
TCP, ICMP, ICSP, IGMP, DHCP, Telnet, FTP, DNS, RFB (for VNC), HTTP
• (1) USB host 2.0, Type A port: firmware upgrade, touch panel file transfer, JPEG image
viewer, HID peripherals
• Bluetooth®: Mouse/Keyboard: HID Profile v1.1, requires MXA-BT, Bluetooth USB
Adapter for Modero X/S Series Touch Panels (FG5968-19) and MXA-HST, Bluetooth
Handset for Modero X/S Touch Panels (FG5968-17)
VIDEO
• Supported Video Codecs:
MPEG2-TS: MPEG-2 Main Profile@High Level up to 720p at 25 fps (decode)
MPEG-2-TS: H.264 High Profile@Layer 4, AAC-LC up to 720p at 25 fps (decode)
MJPEG up to 720p at 25 fps (decode)
• Supported Video Transport Streams: MPEG-TS for MPEG2 and H.264; HTTP for
MJPEG
• Max Number of Active Video Streams: One decode
AUDIO
• Microphone: -42 dB ±3 dB sensitivity FET microphone
• Speakers: 4 ohm, 1.5 Watt, 500 Hz cutoff frequency
• Supported Audio Codecs:
MP2 Layer I and II, MP3 (8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32
kHz, 44.1 kHz, 48 kHz)
AAC-LC (8 kHz, 96 kHz)
G.711 with µLaw (VoIP encode/decode at 8 kHz)
• File Formats: WAV, MP3 (as part of touch panel file only - no USB storage)
• Intercom: Full Duplex VoIP, SIP v2.0 (supported with AMX-CSG)
10
Modero S Series G4 Touch Panels Instruction Manual
MST/D-1001 - 10.1" S Series Touch Panels
MSD-1001-L Specifications (Cont.)
GRAPHICS ENGINE
AMX G4: AMX's exclusive, powerful G4 graphics engine – the driving force behind the
advanced graphics and image processing capability on a variety of AMX Touch Panels
and other devices (see TPD4 Operations Guide for more information)
EMBEDDED APPLICATIONS • Remote Management: VNC Server, G4 Web Control
• Video Conferencing: Panel-to-panel and video chat (the MSD-1001 receives video and
returns audio)
• Audio Conferencing: Audio (Full Duplex Intercom)
FRONT PANEL
COMPONENTS
Sleep Button: Sleep button to activate sleep mode and power off. Also provides access to
setup pages (can be disabled)
Programmable Red/Green LEDs: Programmable red/green LED in the front, left and right
sides of the panel, LEDs are beautifully recessed and nearly invisible when not lit
CONNECTIONS
• Ethernet: 10/100 port, RJ-45 connector
• USB: (1) USB host 2.0, type A port
• Power: PoE (Power over Ethernet), 802.3af, class 0
ENVIRONMENTAL
•
•
•
•
•
Temperature (Operating): 32° F to 104° F (0° C to 40° C)
Temperature (Storage): 4° F to 140° F (-20° C to 60° C)
Humidity (Operating): 20% to 85% RH
Humidity (Storage): 5% to 85% RH
Power ("Heat") Dissipation:
On: 27.3 BTU/hr
Standby: 10.9 BTU/hr
INCLUDED ACCESSORIES
• Installation Template 10.1" S Series (68-2265-03)
OPTIONAL ACCESSORIES
• MSA-MMK-10, Multi Mount Kit, 10.1" Modero S Wall Mount (FG2265-11)
• MSA-RMK-10, Rack Mount Kit for 10" Modero S Series Wall Mount Touch Panel
(FG2265-14)
• MSA-AMK-10, Any Mount Kit for 10.1" Modero S Series Wall Mount Touch Panel
(FG2265-26)
• MXA-MP, Modero X/S Series Multi Preview (FG5968-20)
• MXA-MPL, Modero X/S Series Multi Preview Live (FG5968-10)
• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant (FG423-83)
• NXA-ENET8-2POE, Gigabit Ethernet Switch (FG2178-63)
• MXA-BT, Bluetooth USB Adapter for Modero X/S Series Touch Panels (FG5968-19)
• MXA-HST, Bluetooth Handset for Modero X/S Series Touch Panels (FG5968-17)
• MXA-CLK, Modero X/S Series Screen Cleaning Kit (FG5968-16)
• CB-MSA-10, Rough-In Box and Cover Plate for 10.1" Modero S Series Wall Mount
Touch Panel (FG2265-08)
Touch Panel Aspect Ratio
While the touch panel screen physical dimensions fall between 16:9 and 16:10, any incoming video stream can be scaled
to 16:9 if needed. This may lead to some letter boxing around the video in some cases.
Modero S Series G4 Touch Panels Instruction Manual
11
MST/D-1001 - 10.1" S Series Touch Panels
12
Modero S Series G4 Touch Panels Instruction Manual
Modero S Series G4 Touch Panels Instruction ManualMST/D-701 - 7" S Series Touch Panels
MST/D-701 - 7" S Series Touch Panels
MST-701 (Tabletop)
Microphone
Sleep Button
USB Port
FIG. 8 MST-701
MST-701 Specifications
MST-701 Specifications
DIMENSIONS (HWD)
4 1/2" x 7 3/8" x 3 3/16" (115 mm x 188 mm x 81 mm)
WEIGHT
1.4 lbs (.635 Kg)
POWER CONSUMPTION
• Full-On: 13 W
• Typical: 7 W
• Standby: 4.5 W
• Shutdown: 0.7 W
• Start-Up Inrush Current: Not applicable due to PoE standard
EXTERNAL POWER
SUPPLY REQUIRED
Optimal performance requires use of one of the following AMX PoE power supplies (not
included):
• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant (FG423-83)
• NXA-ENET8-2POE, Gigabit PoE Ethernet Switch (FG2178-63)
CERTIFICATIONS
• FCC Part 15 Class B
• CE EN 55022
• CE EN 55024
• CE EN 60950-1
• IEC 60950-1
• C-Tick CISPR 22 Class B
• IC CISPR 22 Class B
• UL 60950-1
• VCCI CISPR 22 Class B
• RoHS
• WEEE
Modero S Series G4 Touch Panels Instruction Manual
13
MST/D-701 - 7" S Series Touch Panels
MST-701 Specifications (Cont.)
TOUCH SCREEN DISPLAY
• Display Type: TFT Active Matrix Color LCD with Fringe Field Switching (FFS) - Wide
viewing angle technology
• Display Size (WH): Landscape: 7.3" x 4.8" (186 mm x 122 mm), 8.8" (222 mm)
diagonal
• Viewable Area (WH): Landscape: 6.05" x 3.54" (154 mm x 90 mm), 7.0" (178 mm)
diagonal
• Resolution: Landscape: 1024x600
• Aspect Ratio: Landscape: 16:9
• Brightness: 400 cd/m2
• Contrast Ratio: 800:1
• Color Depth: 16.7M colors
• Illumination: LED
• Touch Overlay: Resistive
VIEWING ANGLE
MEMORY
89°/89°/89°/89° (Up/Down/Left/Right)
• SDRAM: 512 MB
• Flash: 4 GB
• Maximum Project Size: 2.4 GB flash available to user
COMMUNICATIONS
• Ethernet: 10/100 port, RJ-45 connector. Supported IP and IP-based protocols: UCP,
TCP, ICMP, ICSP, IGMP, DHCP, Telnet, FTP, DNS, RFB (for VNC), HTTP
• USB: (1) USB host 2.0, Type A port: Firmware upgrade, touch panel file transfer, JPEG
image viewer, HID Peripherals
• Bluetooth®: Mouse/Keyboard: HID Profile v1.1, requires MXA-BT, Bluetooth USB
Adapter for Modero X/S Series Touch Panels (FG5968-19) and MXA-HST, Bluetooth
Handset for Modero X/S Touch Panels (FG5968-17)
VIDEO
• Supported Video Codecs:
MPEG2-TS: MPEG-2 Main Profile@High Level up to 720p at 25 fps (decode only)
MPEG-2-TS: H.264 High Profile@Layer 4, AAC-LC up to 720p at 25 fps (decode)
MJPEG up to 720p at 25 fps (decode only)
• Supported Video Transport Streams: MPEG-TS for MPEG2 and H.264; HTTP for
MJPEG
• Max Number of Active Video Streams: One decode
AUDIO
• Microphone: -42 dB ±3 dB sensitivity FET microphone
• Speakers: 4 ohm, 1.5 Watt, 500 Hz cutoff frequency
• Supported Audio Codecs:
MP2 Layer I and II, MP3 (8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32
kHz, 44.1 kHz, 48 kHz)
AAC-LC (8 kHz, 96 kHz)
G.711 with µLaw (VoIP encode/decode at 8 kHz)
• File Formats: WAV, MP3 (as part of touch panel file only - no USB storage)
• Intercom: Full Duplex VoIP, SIP v2.0 (supported with AMX-CSG)
GRAPHICS ENGINE
AMX G4: AMX's exclusive, powerful G4 graphics engine – the driving force behind the
advanced graphics and image processing capability on a variety of AMX Touch Panels
and other devices (see TPD4 Operations Guide for more information)
EMBEDDED APPLICATIONS • Remote Management: VNC Server, G4 Web Control
• Panel-to-Panel Conferencing: Receives audio and video and returns audio for panelto-panel communication
• Audio Conferencing: Audio (Full Duplex Intercom)
FRONT PANEL
COMPONENTS
Sleep Button: Sleep button to activate sleep mode and power off. Also provides access to
setup pages (can be disabled)
CONNECTIONS
• Ethernet: 10/100 port, RJ-45 connector
• USB: (1) USB host 2.0, Type A port
• Power: PoE (Power over Ethernet), 802.3af, class 3
14
Modero S Series G4 Touch Panels Instruction Manual
Modero S Series G4 Touch Panels Instruction ManualMST/D-701 - 7" S Series Touch Panels
MST-701 Specifications (Cont.)
ENVIRONMENTAL
• Temperature (Operating): 32° F to 104° F (0° C to 40° C)
• Temperature (Storage): 4° F to 140° F (-20° C to 60° C)
• Humidity (Operating): 20% to 85% RH
• Humidity (Storage): 5% to 85% RH
• Power ("Heat") Dissipation:
On: 27.3 BTU/hr
Standby: 10.9 BTU/hr
INCLUDED ACCESSORIES
• MXA-USB-C, USB Port Cover Kit, Modero X Series Touch Panel (FG5968-18)
• Cat5e Ethernet Cable, Flat Black (ECA2265-10)
• UTP CAT.5E Snap In Coupler, Black (64-5968-01)
OPTIONAL ACCESSORIES
• MSA-STMK-07, Secure Table Mount Kit for 7" Modero S Tabletop Touch Panel
(FG2265-17)
• MXA-MP, Modero X/S Series Multi Preview (FG5968-20)
• MXA-MPL, Modero X/S Series Multi Preview Live (FG5968-10)
• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant (FG423-83)
• NXA-ENET8-2POE, Gigabit Ethernet Switch (FG2178-63)
• MXA-BT, Bluetooth USB Adapter for Modero X/S Series Touch Panels (FG5968-19)
• MXA-HST, Bluetooth Handset for Modero X/S Series Touch Panels (FG5968-17)
• HPG-10-10K, 3/4" Mini-Grommet, 10-Pack (FG570-01-10K)
• MXA-CLK, Modero X/S Series Screen Cleaning Kit (FG5968-16)
• MXA-USB-C, USB Port Covers for the Modero X/S Series Touch Panels (FG5968-18)
MSD-701-L (Landscape Wall Mount)
The MSD-701-L 7" (Landscape) Wall Mount Touch Panel (FG2265-02) features brilliant 24-bit color depth, PoE
connectivity, and streaming video. The MSD-701-L also supports Bluetooth keyboard and mouse via the optional
MXA-BT Bluetooth Adapter.
Sleep Button
Microphone
Backbox
Left
LED
Right
LED
(side view)
FIG. 9 MSD-701-L
MSD-701-L Specifications
MSD-701-L Specifications
DIMENSIONS (HWD)
Landscape: 4 7/8" x 7 3/8" x 2 1/4" (123.9 mm x 187.5 mm x 58 mm), with Backbox
WEIGHT
• 1.05 lbs (.680 Kg), with Backbox
• 0.8 lbs (.363 Kg), without Backbox
Modero S Series G4 Touch Panels Instruction Manual
15
MST/D-701 - 7" S Series Touch Panels
MSD-701-L Specifications (Cont.)
POWER CONSUMPTION
• Full-On: 11 W
• Typical: 7.5 W
• Standby: 4.5 W
• Shutdown: 0.7 W
• Start-Up Inrush Current: Not applicable due to PoE standard
EXTERNAL POWER
SUPPLY REQUIRED
Optimal performance requires use of one of the following AMX PoE power supplies (not
included):
• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant (FG423-83)
• NXA-ENET8-2POE, Gigabit PoE Ethernet Switch (FG2178-63)
CERTIFICATIONS
• FCC Part 15 Class B
• CE EN 55022
• CE EN 55024
• CE EN 60950-1
• IEC 60950-1
• C-Tick CISPR 22 Class B
• IC CISPR 22 Class B
• UL 60950-1
• VCCI CISPR 22 Class B
• RoHS
• WEEE
TOUCH SCREEN DISPLAY
• Display Type: TFT Active Matrix Color LCD with Fringe Field Switching (FFS) - Wide
viewing angle technology
• Display Size (WH): Landscape: 7.3" x 4.8" (186 mm x 122 mm), 8.8" (222 mm)
diagonal
• Viewable Area (WH): Landscape: 6.05" x 3.54" (154 mm x 90 mm), 7.0" (178 mm)
diagonal
• Resolution: Landscape: 1024x600
• Aspect Ratio: Landscape: 16:9
• Brightness: 400 cd/m2
• Contrast Ratio: 800:1
• Color Depth: 16.7M colors
• Illumination: LED
• Touch Overlay: Resistive
VIEWING ANGLE
MEMORY
89°/89°/89°/89° (Up/Down/Left/Right)
• SDRAM: 512 MB
• Flash: 4 GB
• Maximum Project Size: 2.4 GB flash available to user
COMMUNICATIONS
• Ethernet: 10/100 port, RJ-45 connector. Supported IP and IP-based protocols: UCP,
TCP, ICMP, ICSP, IGMP, DHCP, Telnet, FTP, DNS, RFB (for VNC), HTTP
• USB: (1) USB host 2.0, Type A port: firmware upgrade, touch panel file transfer, JPEG
image viewer, HID peripherals
• Bluetooth®: Mouse/Keyboard: HID Profile v1.1, requires MXA-BT, Bluetooth USB
Adapter for Modero X/S Series Touch Panels (FG5968-19) and MXA-HST, Bluetooth
Handset for Modero X/S Touch Panels (FG5968-17)
VIDEO
• Supported Video Codecs:
MPEG2-TS: MPEG-2 Main Profile@High Level up to 720p at 25 fps (decode only)
MPEG-2-TS: H.264 High Profile@Layer 4, AAC-LC up to 720p at 25 fps (decode)
MJPEG up to 720p at 25 fps (decode only)
• Supported Video Transport Streams: MPEG-TS for MPEG2 and H.264; HTTP for MJPEG
• Max Number of Active Video Streams: One decode
16
Modero S Series G4 Touch Panels Instruction Manual
Modero S Series G4 Touch Panels Instruction ManualMST/D-701 - 7" S Series Touch Panels
MSD-701-L Specifications (Cont.)
AUDIO
• Microphone: -42 dB ±3 dB sensitivity FET microphone
• Speakers: 4 ohm, 1.5 Watt, 500 Hz cutoff frequency
• Supported Audio Codecs:
MP2 Layer I and II, MP3 (8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32
kHz, 44.1 kHz, 48 kHz)
AAC-LC (8 kHz, 96 kHz)
G.711 with µLaw (VoIP encode/decode at 8 kHz)
• File Formats: WAV, MP3 (as part of touch panel file only - no USB storage)
• Intercom: Full Duplex VoIP, SIP v2.0 (supported with AMX-CSG)
GRAPHICS ENGINE
AMX G4: AMX's exclusive, powerful G4 graphics engine – the driving force behind the
advanced graphics and image processing capability on a variety of AMX Touch Panels
and other devices (see TPD4 Operations Guide for more information)
EMBEDDED APPLICATIONS • Remote Management: VNC Server, G4 Web Control
• Panel-to-Panel Conferencing: Receives audio and video and returns audio for panelto-panel communication
• Audio Conferencing: Audio (Full Duplex Intercom)
FRONT PANEL
COMPONENTS
• Sleep Button: Sleep button to activate sleep mode and powering off. Also provides
access to setup pages (can be disabled)
• Programmable Red/Green LEDs: Programmable red/green LED in the front, left and
right sides of the panel, LEDs are beautifully recessed and nearly invisible when not lit
CONNECTIONS
• Ethernet: 10/100 port, RJ-45 connector
• USB: (1) USB host 2.0, type A port
• Power: PoE (Power over Ethernet), 802.3af, class 0
ENVIRONMENTAL
• Temperature (Operating): 32° F to 104° F (0° C to 40° C)
• Temperature (Storage): 4° F to 140° F (-20° C to 60° C)
• Humidity (Operating): 20% to 85% RH
• Humidity (Storage): 5% to 85% RH
• Power ("Heat") Dissipation:
On: 22.2 BTU/hr
Standby: 14.3 BTU/hr
INCLUDED ACCESSORIES
• Installation Template 7" S Series (68-2265-02)
OPTIONAL ACCESSORIES
• MXA-MP, Modero X/S Series Multi Preview (FG5968-20)
• MXA-MPL, Modero X/S Series Multi Preview Live (FG5968-10)
• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant (FG423-83)
• NXA-ENET8-2POE, Gigabit PoE Ethernet Switch (FG2178-63)
• MXA-BT, Bluetooth USB Adapter for Modero X/S Series Touch Panels (FG5968-19)
• MXA-HST, Bluetooth Handset for Modero X/S Series Touch Panels (FG5968-17)
• CB-MXSA-07, Rough-In Box and Cover Plate for Modero X/S Series Touch Panel, 7"
(FG2265-09)
• MSA-MMK-07, Multi Mount Kit for 7" Modero S Series Wall Mount Touch Panel
(FG2265-12)
• MSA-RMK-07, Rack Mount Kit for Modero S Series Touch Panel, 7" (FG2265-15)
• MSA-AMK-07, Any Mount Kit for 7" Modero S Series Wall Mount Touch Panel
(FG2265-25)
• MXA-CLK, Modero X/S Series Screen Cleaning Kit (FG5968-16)
• MXA-USB-C, USB Port Covers for the Modero X/S Series Touch Panels (FG5968-18)
Touch Panel Aspect Ratio
While the touch panel screen physical dimensions fall between 16:9 and 16:10, any incoming video stream can be scaled
to 16:9 if needed. This may lead to some letter boxing around the video in some cases.
Modero S Series G4 Touch Panels Instruction Manual
17
MST/D-701 - 7" S Series Touch Panels
18
Modero S Series G4 Touch Panels Instruction Manual
MST/D-431 - 4.3" S Series Touch Panels
MST/D-431 - 4.3" S Series Touch Panels
MST-431 (Tabletop)
Sleep Button
Microphone
USB Port
FIG. 10 MST-431
MST-431 Specifications
MST-431 Specifications
DIMENSIONS (HWD)
3 1/4" x 5 1/16" x 3 1/8" (82 mm x 128 mm x 79 mm)
WEIGHT
0.9 lbs (.4 Kg)
POWER CONSUMPTION
• Full-On: 4 W
• Typical: 3 W
• Standby: 2 W
• Shutdown: 0.7 W
• Start-Up Inrush Current: Not applicable due to PoE standard
EXTERNAL POWER
SUPPLY REQUIRED
Optimal performance requires use of one of the following AMX PoE power supplies (not
included):
• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant (FG423-83)
• NXA-ENET8-2POE, Gigabit PoE Ethernet Switch (FG2178-63)
CERTIFICATIONS
• FCC Part 15 Class B
• CE EN 55022
• CE EN 55024
• CE EN 60950-1
• IEC 60950-1
• C-Tick CISPR 22 Class B
• IC CISPR 22 Class B
• UL 60950-1
• VCCI CISPR 22 Class B
• RoHS
• WEEE
Modero S Series G4 Touch Panels Instruction Manual
19
MST/D-431 - 4.3" S Series Touch Panels
MST-431 Specifications (Cont.)
TOUCH SCREEN DISPLAY
• Display Type: TFT Active Matrix Color LCD
• Display Size (WH): Landscape: 5" x 3.4" (128 mm x 87 mm), 6" (152 mm) diagonal
• Viewable Area (WH): Landscape: 3.7" x 2.1" (95 mm x 54 mm), 4.3" (109 mm)
diagonal
• Resolution: Landscape: 480x272
• Aspect Ratio: Landscape: 16:9
• Brightness: 350 cd/m2
• Contrast Ratio: 600:1
• Color Depth: 16.7M colors
• Illumination: LED
• Touch Overlay: Resistive
VIEWING ANGLE
MEMORY
40°/80°/65°/65° (Up/Down/Left/Right)
• SDRAM: 512 MB
• Flash: 4 GB
• Maximum Project Size: 2.4 GB flash available to user
COMMUNICATIONS
• Ethernet: 10/100 Auto MDI-X port, RJ-45 connector. Supported IP and IP-based
protocols: UCP, TCP, ICMP, ICSP, IGMP, DHCP, Telnet, FTP, DNS, RFB (for VNC),
HTTP
• USB: (1) USB host 2.0, Type A port: Firmware upgrade, touch panel file transfer, JPEG
image viewer, HID Peripherals
• Bluetooth®: Mouse/Keyboard: HID Profile v1.1, requires MXA-BT, Bluetooth USB
Adapter for Modero X/S Series Touch Panels (FG5968-19) and MXA-HST, Bluetooth
Handset for Modero X/S Touch Panels (FG5968-17)
VIDEO
AUDIO
Supported Video Codecs: MJPEG up to 720p at 25 fps (decode only)
• Microphone: -42 dB ±3 dB sensitivity FET microphone
• Speakers: 4 ohm, 1.5 Watt, 500 Hz cutoff frequency
• Supported Audio Codecs:
MP2 Layer I and II, MP3 (8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32
kHz, 44.1 kHz, 48 kHz)
AAC-LC (8 kHz, 96 kHz)
G.711 with µLaw (VoIP encode/decode at 8 kHz)
• File Formats: WAV, MP3 (as part of touch panel file only - no USB storage)
• Intercom: Full Duplex VoIP, SIP v2.0 (supported with AMX-CSG)
GRAPHICS ENGINE
AMX G4: AMX's exclusive, powerful G4 graphics engine – the driving force behind the
advanced graphics and image processing capability on a variety of AMX Touch Panels
and other devices (see TPD4 Operations Guide for more information)
EMBEDDED APPLICATIONS • Remote Management: VNC Server, G4 Web Control, AMX Resource Management Suite
• Video Conferencing: Panel-to-panel and video chat (the MST-431 receives video and
returns audio)
• Audio Conferencing: Audio (Full Duplex Intercom)
FRONT PANEL
COMPONENTS
CONNECTIONS
Sleep Button: Sleep button to activate sleep mode and powering off. Also provides
access to setup pages (can be disabled)
• Ethernet: 10/100 Auto MDI-X port, RJ-45 connector
• USB: (1) USB host 2.0, Type A port
• Power: PoE (Power over Ethernet), 802.3af, class 2
ENVIRONMENTAL
• Temperature (Operating): 32° F to 104° F (0° C to 40° C)
• Temperature (Storage): 4° F to 140° F (-20° C to 60° C)
• Humidity (Operating): 20% to 85% RH
• Humidity (Storage): 5% to 85% RH
• Power ("Heat") Dissipation:
• On: 13.6 BTU/hr
• Standby: 10.9 BTU/hr
20
Modero S Series G4 Touch Panels Instruction Manual
MST/D-431 - 4.3" S Series Touch Panels
MST-431 Specifications (Cont.)
INCLUDED ACCESSORIES
• MXA-USB-C, USB Port Cover Kit, Modero X Series Touch Panel (FG5968-18)
• Cat5e Ethernet Cable, Flat Black (ECA2265-10)
• UTP CAT.5E Snap In Coupler, Black (64-5968-01)
OPTIONAL ACCESSORIES
• MSA-STMK-43, Secure Table Mount Kit for 4.3" Modero S Tabletop Touch Panel
(FG2265-18)
• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant (FG423-83)
• NXA-ENET8-2POE, Gigabit Ethernet Switch (FG2178-63)
• MXA-BT, Bluetooth USB Adapter for Modero X/S Series Touch Panels (FG5968-19)
• MXA-HST, Bluetooth Handset for Modero X/S Series Touch Panels (FG5968-17)
• HPG-10-10K, 3/4" Mini-Grommet, 10-Pack (FG570-01-10K)
• MXA-CLK, Modero X/S Series Screen Cleaning Kit (FG5968-16)
• MXA-USB-C, USB Port Covers for the Modero X/S Series Touch Panels (FG5968-18)
MSD-431-L (Wall Mount - Landscape)
The MST-431-L 4.3" Wall Mount (Landscape) Touch Panel (FG2265-07) features advanced technology empowering
users to conduct seamless meetings including VoIP, brilliant 24-bit color depth, PoE connectivity, USB and streaming
video. The MSD-431-L also supports Bluetooth keyboard and mouse use via the optional MXA-BT Bluetooth Adapter.
Sleep Button
Microphone
Backbox
Right
LED
Left
LED
(side view)
FIG. 11 MSD-431-L
MSD-431-L Specifications
MSD-431-L Specifications
DIMENSIONS (HWD)
Landscape: 3 3/8" x 5 1/16" x 2 5/8" (86 mm x 128 mm x 66 mm)
WEIGHT
• 0.65 lbs (.295 Kg), with Backbox
• 0.5 lbs (.225 Kg), without Backbox
POWER CONSUMPTION
• Full-On: 5 W (max)
• Typical: 3 W
• Standby: 2 W
• Shutdown: 0.7 W
• Start-Up Inrush Current: Not applicable due to PoE standard
EXTERNAL POWER
SUPPLY REQUIRED
Optimal performance requires use of one of the following AMX PoE power supplies (not
included):
• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant (FG423-83)
• NXA-ENET8-2POE, Gigabit PoE Ethernet Switch (FG2178-63)
Modero S Series G4 Touch Panels Instruction Manual
21
MST/D-431 - 4.3" S Series Touch Panels
MSD-431-L Specifications (Cont.)
CERTIFICATIONS
• FCC Part 15 Class B
• CE EN 55022
• CE EN 55024
• CE EN 60950-1
• IEC 60950-1
• C-Tick CISPR 22 Class B
• IC CISPR 22 Class B
• UL 60950-1
• VCCI CISPR 22 Class B
• RoHS
• WEEE
TOUCH SCREEN DISPLAY
• Display Type: TFT Active Matrix Color LCD
• Display Size (WH): Landscape: 5" x 3.4" (128 mm x 87 mm), 6" (152 mm) diagonal
• Viewable Area (WH): Landscape: 3.7" x 2.1" (95 mm x 54 mm), 4.3" (109 mm) diagonal
• Resolution: Landscape: 480x272
• Aspect Ratio: Landscape: 16:9
• Brightness: 350 cd/m2
• Contrast Ratio: 600:1
• Color Depth: 16.7M colors
• Illumination: LED
• Touch Overlay: Resistive
VIEWING ANGLE
MEMORY
40°/80°/65°/65° (Up/Down/Left/Right)
• SDRAM: 512 MB
• Flash: 4 GB
• Maximum Project Size: 2.4 GB flash available to user
COMMUNICATIONS
• Ethernet: 10/100 Auto MDI-X port, RJ-45 connector. Supported IP and IP-based
protocols: UCP, TCP, ICMP, ICSP, IGMP, DHCP, Telnet, FTP, DNS, RFB (for VNC),
HTTP
• USB: (1) USB host 2.0, Type A port: firmware upgrade, touch panel file transfer, JPEG
image viewer, HID peripherals
• Bluetooth®: Mouse/Keyboard: HID Profile v1.1, requires MXA-BT, Bluetooth USB
Adapter for Modero X/S Series Touch Panels (FG5968-19) and MXA-HST, Bluetooth
Handset for Modero X/S Touch Panels (FG5968-17)
VIDEO
AUDIO
Supported Video Codecs: MJPEG up to 720p at 25 fps (decode only)
• Microphone: -42 dB ±3 dB sensitivity FET microphone
• Speakers: 4 ohm, 1.5 Watt, 500 Hz cutoff frequency
• Supported Audio Codecs:
MP2 Layer I and II, MP3 (8 kHz, 11.025 kHz, 12 kHz, 16 kHz, 22.05 kHz, 24 kHz,
32 kHz, 44.1 kHz, 48 kHz)
AAC-LC (8 kHz, 96 kHz)
G.711 with µLaw (VoIP encode/decode at 8 kHz)
• File Formats: WAV, MP3 (as part of touch panel file only - no USB storage)
• Intercom: Full Duplex VoIP, SIP v2.0 (supported with AMX-CSG)
GRAPHICS ENGINE
AMX G4: AMX's exclusive, powerful G4 graphics engine – the driving force behind the
advanced graphics and image processing capability on a variety of AMX Touch Panels
and other devices (see TPD4 Operations Guide for more information)
EMBEDDED APPLICATIONS • Remote Management: VNC Server, G4 Web Control, AMX Resource Management
Suite
• Video Conferencing: Panel-to-panel and video chat (the MSD-431 receives video and
returns audio)
• Audio Conferencing: Audio (Full Duplex Intercom)
22
Modero S Series G4 Touch Panels Instruction Manual
MST/D-431 - 4.3" S Series Touch Panels
MSD-431-L Specifications (Cont.)
FRONT PANEL
COMPONENTS
• Sleep Button: Sleep button to activate sleep mode and power off. Also provides access
to setup pages (can be disabled)
• Programmable Red/Green LEDs: Programmable red/green LED in the front, left and
right sides of the panel, LEDs are beautifully recessed and nearly invisible when not lit
CONNECTIONS
• Ethernet: 10/100 Auto MDI-X port, RJ-45 connector
• USB: (1) USB host 2.0, type A port
• Power: PoE (Power over Ethernet), 802.3af, class 3
ENVIRONMENTAL
• Temperature (Operating): 32° F to 104° F (0° C to 40° C)
• Temperature (Storage): 4° F to 140° F (-20° C to 60° C)
• Humidity (Operating): 20% to 85% RH
• Humidity (Storage): 5% to 85% RH
• Power ("Heat") Dissipation:
On: 13.6 BTU/hr
Standby: 10.9 BTU/hr
INCLUDED ACCESSORIES
• Installation Template 4.3" S Series (68-5968-02)
OPTIONAL ACCESSORIES
• MSA-MMK-43, Multi Mount Kit, 4.3" Modero S Wall Mount (FG2265-13)
• MXA-MP, Modero X/S Series Multi Preview (FG5968-20)
• MXA-MPL, Modero X/S Series Multi Preview Live (FG5968-10)
• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant (FG423-83)
• NXA-ENET8-2POE, Gigabit PoE Ethernet Switch (FG2178-63)
• MXA-BT, Bluetooth USB Adapter for Modero X/S Series Touch Panels (FG5968-19)
• MXA-HST, Bluetooth Handset for Modero X/S Series Touch Panels (FG5968-17)
• CB-MSA-43, Rough-In Box and Cover Plate for the 4.3" Wall Mount Modero S Series
Touch Panel (FG2265-10)
• MXA-CLK, Modero X/S Series Screen Cleaning Kit (FG5968-16)
• MXA-USB-C, USB Port Covers for the Modero X/S Series Touch Panels (FG5968-18)
Touch Panel Aspect Ratio
While the touch panel screen physical dimensions fall between 16:9 and 16:10, any incoming video stream can be scaled
to 16:9 if needed. This may lead to some letter boxing around the video in some cases.
Modero S Series G4 Touch Panels Instruction Manual
23
MST/D-431 - 4.3" S Series Touch Panels
24
Modero S Series G4 Touch Panels Instruction Manual
Installing Tabletop (MXT) Panels
Installing Tabletop (MXT) Panels
MST-1001/701/431
Detailed specifications drawings for the MST-1001 are available to download from www.amx.com.
Detailed specifications drawings for the MST-701 are available to download from www.amx.com.
Detailed specifications drawings for the MST-431 are available to download from www.amx.com.
Connector Locations
USB peripherals (mouse, keyboard, etc.) may be connected to the USB port on the rear of the device. Updates to the
device’s firmware can also made via the USB port.
Note that FIG. 12 shows a MST-1001, but the connector locations are similar for all MST panels:
USB Port
RJ-45 Port
FIG. 12 MST-1001 Connector Location
Power via Power Over Ethernet
Power for the MST-1001 is supplied via Power Over Ethernet (PoE), utilizing an AMX-certified, capacitive touchcompliant PoE injector such as the PS-POE-AT-TC High Power PoE Injector (FG423-83) or other approved AMX PoE
power source.
The incoming Ethernet cable should be connected to the RJ45 port on the panel.
Modero S Series G4 Touch Panels Instruction Manual
25
Installing Tabletop (MXT) Panels
26
Modero S Series G4 Touch Panels Instruction Manual
Installing Wall-Mount (MXD) Panels
Installing Wall-Mount (MXD) Panels
A Note About Wall and Rack Installation
AMX DEVICE
Some products are installed in areas of differing temperature and cooling methodologies. These include products
installed in walls, racks, cabinets, etc. Those areas may have different temperatures and/or cooling approaches that must
be taken into consideration to maintain the product within the specified operating temperature.
FIG. 13 shows an AMX device installed in a wall with a filled volume (such as with insulation or concrete), as well as
with a closed volume (such as between studs in an otherwise finished wall). The diagram shows how heat generated by
the device or other devices may have no way to escape, and may build up to levels that may affect device operation.
T1
T2
FILLED OR CLOSED
VOLUME, LIMITED OR
NO CONVECTION
T1, T2 < TOpMax
T1, T2 > TOpMin
FIG. 13 Heat convection in filled or closed volume, limited or no convection
In FIG. 14, the diagram displays an AMX device in a typical rack mounting, with full air circulation around the front and
back of the device. In this case, the main concern is with heat building up between components, possibly to levels that
may affect device operation.
T3
T1
AMX DEVICE
T2
T4
RACK MOUNTED DEVICES
T1, T2, T3, T4 < TOpMax
T1, T2, T3, T4 > TOpMin
FIG. 14 Heat convection in rack-mounted devices
Modero S Series G4 Touch Panels Instruction Manual
27
Installing Wall-Mount (MXD) Panels
Installation Recommendations
During any installation, a lack of ventilation may produce conditions that may adversely affect the device’s operation. In
these circumstances, special care must be made to make sure that temperatures within enclosed areas do not exceed the
device’s maximum rated temperature.
While the outside temperature of the device may be at or below its maximum
operating temperature, special care must be taken before and during installation to
ensure that the maximum operating temperature is not exceeded within wall or rack
installation spaces.
MSD-1001/701/431-L
Detailed specifications drawings for the MSD-1001-L are available to download from www.amx.com.
Detailed specifications drawings for the MSD-701-L are available to download from www.amx.com.
Detailed specifications drawings for the MSD-431-L are available to download from www.amx.com.
28
Modero S Series G4 Touch Panels Instruction Manual
Installing Wall-Mount (MXD) Panels
Removing the Backbox
S Series touch panels are shipped pre-installed in a plastic Backbox. This Backbox must be detached from the panel
before installation.
Also, after installation there are circumstances (such as firmware updates or other
maintenance) that will require accessing the device’s Micro-USB ports. In these
cases, the panel may need to be removed from the Backbox.
Wall-mount S Series touch panels are held in place to the Backbox via latch hooks and clips on the Backbox (FIG. 21).
The clips that lock down the panel’s edges must be unlatched in order to remove the touch panel from the Backbox.
Read the following instructions and be careful when removing the touch panel from
it’s Backbox. Improper handling or excessive force can result in damage to the
panel’s glass touch surface.
Detaching the MSD-1001-L Backbox
1. Orient the panel so that the panel/Backbox assembly is upside-down, and the glass is facing away from you. The
bottom of the Backbox should be facing up.
2. On the bottom of the Backbox, press down on the front corners of the plastic (on the side nearest to the glass) to flex
it enough to unhinge the panel.
Press down with thumbs to release
Rotate Backbox back
and lift off of panel
The panels in this illustration are
shown upside-down. This orientation
makes it easy to press down on the
plastic Backbox to disengage the
latches that secure the bottom of the
panel to the bottom of the Backbox.
TOP
MSD-1001-L
Press down with thumbs to release
Press down with
thumbs to release
Rotate Backbox back
and lift off of panel
MSD-701-L
Rotate Backbox back
and lift off of panel
MSD-431-L
FIG. 15 S Series Backboxes
Note that at this point, the top edge of the panel is still latched into the top of the Backbox.
3. Rotate the top of the Backbox away from the top of the panel and carefully lift it away. Be careful not to pull on the
cables or connectors.
Modero S Series G4 Touch Panels Instruction Manual
29
Installing Wall-Mount (MXD) Panels
Installation
Refer to A Note About Wall and Rack Installation on page 27 for important notes
on thermal concerns with Wall and Rack Installations.
S Series touch panels may be installed directly into a solid surface environment, using either solid surface screws or the
included locking tabs for different mounting options. Once installed, the panel is contained within a clear outer housing
known as the Backbox (FIG. 16).
Locking tabs
MXD-1001-L
Locking tab
Locking tabs
Locking tab
MXD-701-L
MXD-431-L
Locking tab
Locking tab
FIG. 16 S Series Backboxes - Locking Tabs
This Backbox is removed to install the device into a wall or when using the optional Rough-In Box accessory. Refer to
Removing the Backbox on page 29 for Backbox removal.
For typical mounting surfaces, such as drywall, use the locking tabs as the primary
method for securing the Backbox to the surface. For thin walls or solid surfaces, use
mounting screws (not included).
30
Modero S Series G4 Touch Panels Instruction Manual
Installing Wall-Mount (MXD) Panels
Installing the S Series Panel into a Wall
S Series touch panels come with a clear plastic Backbox designed to attach the panel to most standard wall materials.
This Backbox has locking tabs to help lock the Backbox to the wall (see FIG. 16).
These locking tabs are only extended AFTER the Backbox is inserted into the wall.
When installing the Backbox, make sure that the assembly is in the correct position
and in the correct place. Once the locking tabs are extended and locked into place,
removing the Backbox may be difficult without having access to the back of the wall
or causing damage to the wall.
MXD-1001-L Dimensions
Notes:
Dimensions in parenthesis are in millimeters
Additional detailed installation and product drawings are available to view/download at www.amx.com
FIG. 17 MST-1001-L
Modero S Series G4 Touch Panels Instruction Manual
31
Installing Wall-Mount (MXD) Panels
MXD-701-L Dimensions
Notes:
Dimensions in parenthesis are in millimeters
Additional detailed installation and product drawings are available to view/download at www.amx.com
FIG. 18 MSD-701-L
32
Modero S Series G4 Touch Panels Instruction Manual
Installing Wall-Mount (MXD) Panels
MXD-431-L Dimensions
Notes:
Dimensions in parenthesis are in millimeters
Additional detailed installation and product drawings are available to view/download at www.amx.com
FIG. 19 MSD-431-L
In order to ensure a stable installation of the MSD-1001-L, the thickness of the wall
material must be a minimum of .50 inches (1.27cm) and a maximum of .875 inches
(2.22cm). The mounting surface should also be smooth and flat.
Installing the Backbox
1. Prepare the area by removing any screws or nails from the drywall before beginning the cutout process.
2. For best results, use the Installation Template provided with the panel to ensure proper placement (FIG. 20):
MXD-1001-L - Template, Backbox, 10.1" Touch Panel, Modero S Series (68-2265-03)
MXD-701-L - Template, Backbox, 7.0" Touch Panel, Modero S Series (68-2265-02)
MXD-431-L - Template, Backbox, 4.3" Touch Panel, Modero S Series (68-2265-01)
The templates are marked to ensure that the touch panel and Backbox are properly aligned.
Modero S Series G4 Touch Panels Instruction Manual
33
Installing Wall-Mount (MXD) Panels
MXD-1001-L
MXD-701-L
MXD-431-L
FIG. 20 S Series Installation Templates
34
Modero S Series G4 Touch Panels Instruction Manual
Installing Wall-Mount (MXD) Panels
Using the included template to select the final placement of the Backbox is highly
recommended. The outside edges of the template are the same dimensions as the
touch panel, which allows you to troubleshoot possible conflicts with wall edges,
doors, and other potential obstacles.
3. After ensuring proper placement, cut out the mounting surface for the Backbox, using the MSD-1001-L Installation
Template as a guide.
Making sure the actual cutout opening is slightly smaller than the provided
dimensions is highly recommended. This provides a margin for error if the opening
needs to be expanded. Too little wall material removed is always better than too
much.
4. Thread the incoming Ethernet and Micro-USB wiring (if Micro-USB access is desired) from their terminal
locations through the surface opening (FIG. 21).
Leave enough slack in the wiring to accommodate any re-positioning of the panel.
5. Remove the Backbox knockouts and thread the incoming wiring through the knockout holes (FIG. 21). Note that
while FIG. 21 shows the MXD-1001-L, the illustration applies to all S Series panels. The only difference is the
dimensions and the number of knockouts and locking tabs.
Mounting Surface
4X Locking tabs
4X Knockouts
Backbox
MSD-1001-L
FIG. 21 MSD-1001-L Backbox Installation
6. Thread the incoming Ethernet and Micro-USB wiring (if USB or Micro-USB access is desired) from the surface
opening and through the knockouts.
7. Push the Backbox into the mounting surface.
Ensure that the locking tabs lie flush against the Backbox and that the Backbox goes freely into the opening.
8. Extend the locking tabs on the sides of the Backbox by tightening the screws inside the box until snug.
Modero S Series G4 Touch Panels Instruction Manual
35
Installing Wall-Mount (MXD) Panels
The maximum recommended torque to screw in the locking tabs on the plastic
Backbox is 5 IN-LB [56 N-CM]. Applying excessive torque while tightening the tab
screws, such as with powered screwdrivers, can strip out the locking tabs or damage
the Backbox.
Not all of the tabs must be extended to lock the Backbox in place, but extending a minimum of the top and
bottom tabs is highly recommended.
Apply enough pressure to the screw head to keep the box flush with the wall: this ensures that the locking tabs
will tighten up against the inside of the wall.
The Backbox is clear to allow visual confirmation that the tabs have been extended and are gripping the wall,
as well as in assisting with removal if necessary.
MSD-1001-L and MSD-701-L only: For additional strength, #4 mounting screws (not included) may be
secured through circular holes located at the left and right sides of the panel. In order to prevent damage to the
touch panel, make sure that these are flush with the Backbox.
9. Insert each connector into its corresponding location along the back of the device:
FIG. 22 shows the connectors on the rear of the MSD-1001-L: .
RJ-45 Port
Micro-USB Port
FIG. 22 Rear of the MSD-1001-L
FIG. 23 shows the connectors on the rear of the MSD-701-L:
RJ-45 Port
Micro-USB Port
FIG. 23 Rear of the MSD-701-L
36
Modero S Series G4 Touch Panels Instruction Manual
Installing Wall-Mount (MXD) Panels
FIG. 24 shows the connectors on the rear of the MSD-431-L:
RJ-45 Port
Micro-USB Port
FIG. 24 Rear of the MSD-431-L
10. Test the incoming wiring by attaching the panel connections to their terminal locations and applying power.
Do not disconnect the connectors from the touch panel. The unit must be installed
with the attached connectors before being inserted into the mounting surface.
Verify that the panel is receiving power and functioning properly to prevent repetition of the installation.
Remove power before continuing with the installation.
11. Latch the panel onto the top hooks on the Backbox and push it down onto the bottom snaps. Press gently but firmly
on the ends until the snaps “click” to lock it down (FIG. 25):
Latch Hooks
Backbox
Snaps
FIG. 25 Installing the MSD-431-L
If a gap is observed between the panel and the Backbox, or feel any binding while
locking down the panel, stop immediately and verify that no cables or other items are
in the way. Do not force the panel into position, as this can cause damage to the
touch screen or the panel electronics.
12. Reconnect the terminal Ethernet and USB to their respective locations on either the Ethernet port or NetLinx
Master.
Modero S Series G4 Touch Panels Instruction Manual
37
Installing Wall-Mount (MXD) Panels
Removing The Touch Panel From the Backbox After Wall Installation
Occasionally it may be necessary to remove the touch panel from the wall to perform routine maintenance, firmware
upgrade or troubleshooting. This section describes the best methods for removing to touch panel from the Backbox
without damaging either.
1. With fingertips placed on the top edge of the bezel, press down on the panel firmly but gently to unhinge the top
clips of the Backbox. Do not press on the glass!
Always push down on the frame of the touch panel. NEVER push on the glass.
2. Once the top clips are release from the touch panel, pull the top panel away from the wall and lift the touch panel up
to separate it from the Backbox. Do not pull on the cables.
3. Unplug the cables if the touch panel needs to be removed for maintenance.
4. To reattach the panel to its Backbox, latch the panel onto the top hooks on the Backbox and push it down onto the
bottom snaps. Press gently but firmly on the ends until the snaps “click” to lock it down.
38
Modero S Series G4 Touch Panels Instruction Manual
Upgrading Firmware
Upgrading Firmware
Overview
Programming the S Series touch panels require the use of NetLinx Studio and TPDesign4, both available from
www.amx.com.
Downloading Firmware Updates From www.amx.com
Before attempting to upgrade the firmware, you must have the appropriate Kit file for your touch panel:
All S Series touch panels share the same firmware.
1. Open the product page for the panel, at www.amx.com (Trade Site).
2. Scroll down to locate Firmware Files on the right side of the page, and click the firmware file link provided. An
example is shown in FIG. 26:
FIG. 26 www.amx.xom - S Series Touch Panel Product Page - Firmware File link
Note that for S Series touch panels, the firmware .KIT file is bundled in a ZIP file that typically also includes a
Readme.TXT file (which provides details on this version of firmware), and a Programming Instructions.TXT file
(which provides basic instructions for upgrading firmware on the panel):
FIG. 27 Example of firmware ZIP file contents
3. Extract the contents of the ZIP file to a known location.
Upgrading Firmware via USB Flash Drive
Firmware and TPDesign4 files may be transferred to the panel made via USB flash drive.
Load the Firmware on a USB Flash Drive
1. Insert the USB flash drive in an available USB port on your PC.
The flash drive must be in either FAT32 or FAT16 format.
32GB is the maximum acceptable size for flash drives used with touch panels
For wall-mounted panels (MSD-xxx), accessing the USB ports may require removing the panel from the wall
mount (if a USB extension was not already installed).
Modero S Series G4 Touch Panels Instruction Manual
39
Upgrading Firmware
2. Create a directory on the USB flash drive with one of the following names, depending on the panel you are
upgrading:
“MST-1001” or “MSD-1001”
“MST-701” or “MSD-701”
"MST-431" or "MSD-431"
Note that the name must match exactly (do not include the quotes)
These directory names are not case-sensitive:
3. Copy the firmware (.kit) file to be transferred (for example, "SW5968_ModeroS_v2_106_08.kit") into this directory
on the flash drive.
Make sure this is the only .kit file in this directory - if not, the latest version will be
used.
4. Eject or unmount the flash drive from the PC.
Transfer the Firmware File From the Flash Drive to the Touch Panel
1. Connect the USB Flash Drive to one of the USB Type A ports on the panel.
The Micro USB port cannot be used for firmware upgrades.
2. Go to the Install Firmware setup page (Configuration->Admin->Install Firmware):
a. Press and hold the Sleep button for 3 seconds to open the Settings page.
FIG. 28 Settings page
b. From the Settings page, select the Configuration page. This may require entering a password.
c. From the Configuration page, select Admin.
d. From the Admin Configuration page, select Install Firmware.
3. In the Firmware Installation page, select New to install new firmware from external disk.
4. The popup page displays the name of the firmware file (for example, "SW5968_ModeroS_v2_106_08.kit").
5. Select Yes, and follow the directions displayed on the popup.
6. Once the panel reboots, it will perform the firmware upgrade.
After the upgrade, the device contains the newly loaded version of firmware.
40
Modero S Series G4 Touch Panels Instruction Manual
Upgrading Firmware
Upgrading from Previous Firmware
S Series panels provide the option to revert the device to the previous firmware run before an upgrade. To upgrade the
device from previously loaded firmware:
1. From the Settings page, select the Configuration page.
2. From the Configuration page, select Admin.
3. From the Admin Configuration page, select Install Firmware.
4. In the Firmware Installation page, select Previous.
5. The Confirmation Dialog box (FIG. 29) will ask “Are you sure you want to install the following firmware?” The
option to choose Yes will be enabled after five seconds. Press Yes to load the firmware listed, and No to return to the
Firmware Installation popup window.
FIG. 29 Previous Firmware installation confirmation dialog
6. If you choose Yes, the device will retrieve the files and then reboot.
Returning to Factory Default Firmware
S Series panels allow the option to return the device to its original factory default firmware, which may be necessary in
certain situations. To return the device to its factory default firmware:
1. From the Settings page, select the Configuration page.
2. From the Configuration page, select Admin.
3. From the Admin Configuration page, select Install Firmware.
4. In the Firmware Installation page, select Factory.
5. The Confirmation Dialog box (FIG. 30) will ask “Are you sure you want to install the following firmware?” The
option to choose Yes will be enabled after five seconds. Press Yes to load the firmware listed, and No to return to the
Firmware Installation popup window.
FIG. 30 Previous Firmware installation confirmation dialog
If you choose Yes, the device will retrieve the files and then reboot.
Upgrading Firmware via NetLinx Studio
Firmware updates to S Series panels can be done via the NetLinx Studio software application. This requires that the
touch panel is connected to a NetLinx Master, and that the Master is on the same network as (or accessible by) the PC
running NetLinx Studio. This is because the firmware file is loaded to the panel through it’s connection to the Master.
S Series panels use Kit files for firmware upgrades. A Kit file (*.kit) is a package of several files, all of which are
required to upgrade the firmware, and are available online via www.amx.com (refer to the device page for firmware
updates).
Modero S Series G4 Touch Panels Instruction Manual
41
Upgrading Firmware
Transferring the KIT File via NetLinx Studio
1. In Netlinx Studio, right-click in the Online Tree tab of the Workspace window and select Refresh System Online
Tree to refresh the device listing. The touch panel should be indicated in the device list.
2. Right-click on the target panel and select Firmware Transfer to open the Send to NetLinx Device dialog.
Alternatively, select Tools > Firmware Transfers > Send To NetLinx Device to open this dialog (FIG. 31):
FIG. 31 NetLinx Studio - Send to NetLinx Device dialog
a. Under Location, select the directory to which the firmware ZIP file was extracted. Use the Browse (...) button
to locate and select a different directory if necessary.
b. All KIT files detected in the selected directory are listed in the Files window. Select a KIT file to transfer.
Note that when a file is selected, file details may be displayed in the text field to the right of the Files
window. Review this text before proceeding to see any important notes or instructions that are specific to
this file.
Also note that the Send button is only enabled once a file has been selected in the Files window.
c. Under Target, enter the Device number for the target touch panel in the Device field.
Use the Online Tree to determine the device's assigned ID (as well as the current firmware version).
Note that if this dialog was accessed by right-clicking on the touch panel in the Online Tree, the Device
Number should already be set correctly.
d. Verify that the Reboot Device option is selected. It is necessary to reboot the panel after a firmware upgrade.

3. Click Send to begin the file transfer.
4. The progress of the transfer operation is indicated in the Progress bars in this dialog, as well as on the panel itself.
5. When the transfer is finished, and the reboot is complete, press the Close button.
If for any reason your Kit file transfer should fail, continue to retry the transfer until
you are successful. DO NOT reboot the Master, or change connections until the
transfer is complete. Failure to complete this operation successfully may result in a
factory repair of the Master.
42
Modero S Series G4 Touch Panels Instruction Manual
Troubleshooting
Troubleshooting
Overview
This section describes the solutions to possible hardware/firmware issues that could arise during the common operation
of a Modero S touch panel.
Panel Doesn’t Respond to Touches
Symptom: The device either does not respond to touches on the touch screen or does not register the touch as being in
the correct area of the screen.
If the screen is off:
The device may be in Display Sleep Mode. Press and hold the Sleep button to wake up the panel.
The device may not be connected to power. Verify that the power source is connected to the device and
receiving power.
Panel Isn’t Appearing in the Online Tree Tab
1. Verify that the System number is the same on both the NetLinx Project Navigator window and the System Settings
page on the device.
2. Verify the proper NetLinx Master IP and connection methods entered into the Master Connection section of the
System Settings page.
Can’t Connect to a NetLinx Master
Symptom: I can’t seem to connect to a NetLinx Master using NetLinx Studio.
Select Settings > Master Comm Settings > Communication Settings > Settings (for TCP/IP), and uncheck the
"Automatically Ping the Master Controller to ensure availability".
The pinging is to determine if the Master is available and to reply with a connection failure instantly if it is not. Without
using the ping feature, a connection may still be attempted, but a failure will take longer to be recognized.
If you are trying to connect to a Master controller that is behind a firewall, you may
have to uncheck this option. Most firewalls will not allow ping requests to pass
through for security reasons.
When connecting to a NetLinx Master controller via TCP/IP, the program will first try to ping the controller before
attempting a connection. Pinging a device is relatively fast and will determine if the device is off-line, or if the TCP/IP
address that was entered was incorrect.
If you decide not to ping for availability and the controller is off-line, or you have an incorrect TCP/IP address, the
program will try for 30-45 seconds to establish a connection.
Only One Modero S Series Panel Indicated in My System
Symptom: I have more than one Modero S Series panel connected to my System Master and only one is indicated.
Multiple NetLinx Compatible devices can be associated for use with a single Master. If the user does not assign a device
number, one will be assigned automatically to the panel. When using multiple panels, different Device Number values
have to be assigned to each panel.
1. Press and hold the Sleep button to open the Settings page.
2. Press the Protected button, enter 1988 into the on-screen Keypad’s password field, and press Done when finished.
3. Enter a Device Number value for the panel into the Device Number Keypad. The range is from 1 - 32000.
Modero S Series G4 Touch Panels Instruction Manual
43
In the ever-changing AV industry, continual education is key to success. AMX University is
dedicated to ensuring that you have the opportunity to gather the information and
experience you need to deliver strong AMX solutions. Plus, AMX courses also help you
earn CEDIA, NSCA, InfoComm, and AMX continuing education units (CEUs).
Visit AMX University online for 24/7/365 access to:
- Schedules and registration for any AMX University course
- Travel and hotel information
- Your individual certification requirements and progress
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.222.0193 • 469.624.8000 • 469-624-7153 fax • 800.932.6993 technical support • www.amx.com
10/14 ©2014 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX. AMX reserves the right to alter specifications without notice at any time.
Increase Your Revenue
through education + knowledge