Owner's manual | MC FM/AM/CD Player Owner`s manual

WWW.denver-electronics.com

Digital AM/FM Stereo Tuner

CD/MP3 Player

Clock

Wall Mountable

Remote Control

IMPORTANT NOTES

* Avoid placing the unit in locations described below:

- Places exposed to direct sunlight or close to heat radiating

appliances such as electric heaters.

- On top of other stereo equipment that radiates too much heat.

- Places lacking ventilation or dusty places.

- Places subject to constant vibration.

- Humid or moist places.

* Do not attempt to clean this unit with chemical solvents as this

might damage the finish. Use a clean dry cloth.

* Be careful not to obstruct the ventilation opening on the rear panel.

* Operate the controls land switches as described in the manual.

* Before turning the power switch on for the first time, make certain all

connecting cords and power cord are properly installed.

* When moving the set, be sure to first pull out the power plug and

remove cords connected to other equipment.

CAUTION:

When operating this unit on 230V mains supply, please note that when the power switch is in the off mode, this does not disconnect the unit from the mains supply, However, please be assured that it is perfectly safe to leave the unit connected to the mains supply.

SAFETY CERTIFICATION

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER.

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

DANGEROUS VOLTAGE

Uninsulated Dangerous voltage, that may be of sufficient magnitude to constitute a risk of electric shock to persons, is present within this product's enclosure.

ATTENTION

The Owner's Manual contains important Operating and maintenance instructions.

For your safely, it is necessary to refer to the manual.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

THIS SYMBOL MEANS THAT THIS UNIT IS DOUBLE

INSULATED AN EARTH CONNECTION IS NOT REQUIRED.

-1-

LOCATION OF CONTROLS

6

7

11

12

13

8

9

10

1

2

3

4

5

14 15 16 17 18 19 20 21 22

29

30

31

32

33

34

35

23

24

25

26

27

28

36

37

38

40

-2-

41

43

42

39

LOCATION OF CONTROLS (cont. .)

1.

SNOOZE Button

Press the SNOOZE button to turn off the sound temporarily

(for about 5 minutes). (Operates in conjunction with the wake-up timer.)

2.

SLEEP / HOUR Button

Press for “sleep to Radio or CD.”

Select 12/24 hour format.

3.

TIMER button

Press to set wake-up and shut-off time.

4.

PRESET UP / REPEAT button

TUNER - Press to retrieve radio station memories presets.

CD - Press to repeat one or all tracks while a CD plays.

5.

MEMORY / CLK-ADJ button

TUNER - Press to preset stations.

CD - Press to program tracks.

CLOCK - Press to set hours and minutes.

6.

POWER Standby Indicator

This indicator lights when AC power cord is connected properly or fresh batteries are installed and unit is OFF.

7.

POWER On / Off Button

Press to turn the power ON or OFF-Standby.

8.

REMOTE Control Sensor

Receives infrared data signals from the remote control.

9.

BACKLIGHT On / Off Button

Press this button to turn LCD display backlight on or off.

-3-

10.

SURROUND button

Press to turn the surround sound ON or OFF.

11.

FOLDER DN button

Press to retrieve MP3 folder down.

12.

MUTE button

Press to temporarily reduce listening volume.

13.

HEADPHONE Jack

Connect a pair of stereo headphone (not supplied) for private listening.

14.

FOLDER UP button

Press to retrieve MP3 folder up.

15.

BASS / + button

Press to increase the bass level.

16.

BASS / - button

Press to reduce the bass level.

17.

CD / TUNING / SKIP downward setting button

CD - Press to skip/search backward.

TUNER - Press to radio stations scan downward.

CLOCK or TIMER - Press select the time downward while setting the clock or timer.

18.

VOLUME Control knob

Turn left or right to adjust sound level up or down.

LOCATION OF CONTROLS (cont. .)

19.

20.

21.

22.

23.

24.

25.

26.

27.

28.

CD / TUNING / SKIP forward setting button

CD - Press to skip/search forward.

TUNER - Press to radio stations scan forward.

CLOCK or TIMER - Press select the time forward while setting the clock or timer.

TREBLE / - button

Press to reduce treble sound level.

TREBLE / + button

Press to increase treble sound level.

CD PLAY / PAUSE Button ( )

Press to begin CD play, to stop temporarily or to scan tuner memory presets.

CD door open button

Press to open the CD door.

TUNER / BAND select button

Sets to tuner (radio) mode and selects the AM or FM band.

MP3 MODE button

Press to select TITLE or ALBUM at MP3 mode.

AUX button

Press to activate operating mode AUX.

INTRO / MONO-ST. button

Press to CD Intro play.

Press to select Stereo or Mono at TUNER FM mode.

This button does not function in MP3 mode.

MODE / REMAIN button

CLOCK - Press mode to set clock time, wake-up or shut-off time.

TUNER - Press mode to select clock time, wake-up or shut-off time of radio frequency.

CD - Press remain to display the remaining time.

This button does not function in MP3 mode.

-4-

29.

30.

31.

32.

33.

34.

36.

37.

38.

39.

40.

SUREWAKE button

Press to turn ON the SureWake function.

LCD display

Shows the operating status in all modes.

DYNAMIC BASS button

Press to turn the dynamic bass ON or OFF.

CD STOP button

Press to stop CD play.

AUX IN MINI Stereo Jack

AUX IN for external sources

& 35. Left and Right AUX OUT Socket

Connect with other external musical instruments to perform AUX OUT functions.

Carrying Recess

SUBWOOFER Jack

To connect with external subwoofer speaker (not included)

AC input socket

To connect the AC cord plug into the socket.

FM Antenna Terminal

Connect single antenna wire (supplied) to terminal marked 75

Ω or dipole antenna (not supplied) to terminals marked 300

Ω

Battery compartment

Install eight “C” size batteries according to the polarity diagram inside the battery compartment.

Alkaline type is recommended.

LOCATION OF CONTROLS (cont. .)

41.

Left channel speaker terminal

Connect the left speaker cable here.

42.

Right channel speaker terminal

Connect the right speaker cable here.

43.

Slot for Wall-Mounting Bracket

Used to connect the mounting (included) to mount the unit on the wall.

REMOTE CONTROL

1

12

17

18

19

10

15

16

13

14

18

19

20

15

16

17

11

12

13

14

21

-5-

1. Power ON/OFF - Standby button

2. Program select buttons

Tuner - To recall preset stations

CD - To recall tracks.

For 1-9, press 0 and 1-9 buttons.

For 10, press 1 and then “0”

For 11 - 19, press 1 and then 1 - 9.

For 20, press 2 and then “0”

For 21 - 29, press 2 and then 1 - 9.

For 30, press 3 and then “0”

3. MEM/CLK-ADJ: CD - Use to program CD tracks for

programmed play / TUNER - Use to programmed preset

memory / CLK-ADJ - Press to set hours and minutes

4. RANDOM/PRESET DN: CD Random play / Tuner - To select

Preset down station

5. MP3 MODE: Press to select TITLE or ALBUM at MP3 mode

6. AUX: Press to activate operating mode AUX

7. SLEEP/HOUR: Press to select the sleep/hour

8. CD - Skip/Search backward / TUNER - Tuning down

9. CD - Skip/Search forward / TUNER - Tuning up

10. VOLUME: Volume up or down

11. MUTE: Muting ON/OFF

12. INTRO/MONO-ST.: CD Intro play / Press to select Stereo or

Mono at TUNER FM mode

13. REPEAT/PRESET UP: CD - Repeat play / This button does

not function in MP3 mode - To select

Preset up station

14. REMAIN/MODE: CD - Check the remaining and clock

time / TUNER - Check clock and frequency

/ This button does not function in MP3 mode

15. FOLDER UP: Press to retrieve MP3 folder up

16. FOLDER DN: Press to retrieve MP3 folder down

17. BAND/TUNER: Press to select the AM/FM band in Tuner

mode / Press to select the Tuner mode

18. PLAY/PAUSE: CD Play/Pause

19. STOP: CD Stop

20. D-BASS (DYNAMIC BASS) button

21. Battery Compartment

INSTALLATION

Installation options:

Wall mount shelf placement one or both speakers attached or detached

To mount the center section on the wall:

Position the bracket on the wall (as shown below) where you want to hang the center unit. Drill 2 holes slightly undersized for a firm fit.

Secure the bracket on the wall using 2 dowels and 2 screws

(supplied)

Mount the center unit onto the wall bracket.

Make sure the mounting tab on the center unit fits securely into the mounting slot on the wall bracket.

Screws and plastic dowels are also provided for speakers if they are to be wall-mounted away from the center section.

To install center section on a table or shelf:

Insert the base from the back of the unit, push until it clicks into position.

To connect the speakers with the center section:

Attach left and right speakers to the center section by sliding down each speaker straight along the side of the center section cabinet.

Connect the left/right speaker lead wires to the speaker terminals.

Pay attention to the polarity. The polarity wires (gray with black stripe) should connect to the red color terminals.

-6-

TO ATTACH THE MAIN UNIT TO

THE BASE

TO RELEASE THE MAIN UNIT

FROM THE BASE

GENERAL OPERATION

Power on

When power is connected for the first time, or if the power cord was unplugged and reconnected.

1.

The STANDBY LED lights, and the LCD panel appears as follows

To set the clock

1.

Press the POWER button to turn the unit off “standby”.

2.

Press the MEMORY button ONCE. The Minute segments display

“00”. The Hour segments flash continuously.

Note: Press the SLEEP/HOUR button to select 24 hour format.

Clock time won’t be showed AM or PM if select 24 hour format.

2.

Press the POWER button. The STANDBY LED turns off and the unit defaults to the tuner function, FM band.

Afterward, when the POWER is turned on, the previously chosen function will be selected.

3.

4.

Press the CD-TUNING-SKIP + or - button to select the desired hour.

Press the MEMORY button again and the minute segments flash.

-7-

5.

Press the CD-TUNING-SKIP + or - button to select the desired minute.

6.

Press the MEMORY button once more. The flashing stops and the time is set.

CD OPERATION

Basic operation

1.

Press POWER button to turn on the power.

2.

Open the CD door, display shows “OPEN”, then load the Disc with the label side up and press it onto the spindle until it

“CLICKS” on the central support of the compartment. Close the door.

4.

If there is no disc in the CD compartment and the CD button is pressed, the LCD will show “NO DISC.”

3.

OPEN LOAD POSITION CLOSE

Step 1 - Push the CD door open button to open CD door.

Step 2 - Loading disc as shown.

Step 3 - Be sure that disc is located in proper position.

Step 4 - Push CD door close.

The disc will spin and the unit will read, display shows

“READING”, the display will show the total number of tracks and the playing time of the disc. Press the CD-play/pause button once. The display will show the first track number on the disc, then indicate the elapsed time as shown, and play will start.

5.

Adjust the VOLUME control to a comfortable level.

6.

Press and release the CD-TUNER-SKIP + or - button to skip to the desired track.

7.

Press and hold the CD-TUNER-SKIP + or - button to search for the desired section within a track.

8.

Press the button to pause temporarily. The LCD will appear as shown below.

Press again to resume.

9.

Press the STOP button to stop playing. The display will show the total number of tracks and the playing time of the disc.

-8-

CD OPERATION (cont.)

To begin program play

The CD player can be programmed to play up to 32 tracks in the order desired.

1.

Press POWER button to turn on the power, then load a disc.

2.

Press the MEMORY button until the LCD appears follows:

3.

Press the CD-TUNING-SKIP + or - button to select the desired track to be programmed.

4.

Press the MEMORY button to store the selection.

When operate the Remote Control, you must press the “0” +

NUMBER button (for example: 01, 02 …) then press the MEMORY button to store the selection.

5.

Repeat steps 3-4 to program additional tracks up to a maximum of

32 tracks.

6.

While display showing tracks programmed, press the button.

The CD player will play the tracks in the order they were programmed.

7.

Press the CD-TUNING-SKIP button to skip forward or backward through programmed tracks.

8.

Any on of the following actions will cancel program play mode.

Press the STOP button twice, then press the button.

Open the CD door

-9-

CD OPERATION (cont.)

To begin random play

1.

Press the RANDOM button by Remote Handset, the “RDM” indicator appears on the LCD.

To begin repeat play

1.

Press the REPEAT button once and the selected track will play repeatedly. The “REPEAT” indicator flashing on the LCD.

2.

Press the button.

3.

To cancel random play, press the RANDOM button once.

2.

Press the REPEAT button again and all tracks will play repeatedly. The “REPEAT” indicator stops flashing on the

LCD.

3.

Press the REPEAT button once more to cancel the repeat mode.

-10-

MP3 OPERATION

Basic operation

1.

Press the CD door button to open the CD door.

2.

Put a disc inside and then close the CD door. After that, reading TOC will start.

After reading TOC

6.

Adjust the VOLUME control to a comfortable level.

7. Press the button to pause temporarily. The LCD will appear as shown below.

3.

Press the FOLDER UP or DN button to select desired folder.

Press again to resume.

8. Press the STOP button to stop playing. The display will show the total number of folder and tracks.

4.

Press the CD-TUNING-SKIP + or - button to select desired track.

5.

Press the button to play the track.

-11-

MP3 OPERATION (cont.)

1.

2.

To begin program play

The CD player can be programmed to play up to 32 tracks in the order desired.

Press POWER button to turn on the power, then load a disc.

Press the MEMORY button once the LCD appears follows:

3.

Press the CD-TUNING-SKIP + or - button to select the desired track to be programmed.

Press the “FOLDER DN or FOLDER UP” button to select the folder.

4.

Press the MEMORY button to store the selection and the

LCD appears follows:

Store the memory thru Remote control.

1.) Press the MEMORY button once.

2.) Press the “FOLDER UP or FOLDER DN” button to selector the

desired folder. Press the “ SKIP / SEARCH ” to

selector the desired file.

3.) Press the MEMORY button to store the selection.

Re-call the memory thru Remote control

1.) Press the MEMORY button to select the pre-store file.

2.) Press CD-PLAY/PAUSE button to play the pre-store file.

You can’t use the direct access button function thru Remote

control. (Press the MEMORY button then press the NUMBER

button directly.)

-12-

5.

Repeat steps 3-4 to program additional tracks up to a maximum of

32 tracks.

6.

While display showing tracks programmed, press the button.

The CD player will play the tracks in the order they were programmed.

7.

Press the CD-TUNING-SKIP button to skip forward or backward through programmed tracks.

8.

Any on of the following actions will cancel program play mode.

Press the STOP button twice, then press the button.

Open the CD door

MP3 OPERATION (cont.)

To begin random play

1.

Press the RANDOM button by Remote Handset, the “RDM” indicator appears on the LCD.

To begin repeat play

1.

Press the REPEAT button once and the selected track will play repeatedly. The “REPEAT” indicator flashing on the LCD.

2.

Press the button.

2.

Press the REPEAT button again and all tracks will play repeatedly. The “REPEAT” indicator stops flashing on the

LCD.

3.

To cancel random play, press the RANDOM button once.

ID3 / Folder Name

1.

Press MP3 mode button once, display shown “Folder Number -

Folder Name - File Number - File Name”.

2.

Press MP3 mode button once again, display shown “Artist -

Album - Title”.

3.

Press the REPEAT button once more to cancel the repeat mode.

-13-

TUNER OPERATION

Basic operation

1.

Press POWER button to turn on the power.

2.

Press the TUNER/BAND button to select AM or FM.

3.

Press the “0” + NUMBER buttons (for example: 01, 02 …) on the remote then press the MEMORY button again to store the selection station and the LCD appears follows:

3.

Press and release the CD-TUNING-SKIP + or - button to select the desired radio station.

4.

Press and hold the CD-TUNING-SKIP + or - button briefly to search up or down for the next receivable station.

To store favorite stations in memory

You can store up to 24 FM and 16 AM stations in memory.

1.

Select the desired radio station as described above.

4.

Press the PRESET UP / REPEAT button to assign the present number.

For example, to store a particular radio station on preset #19, you can press the PRESET UP / REPEAT button 19 times

The LCD shows the preset number.

2.

Press the MEMORY button and the LCD appears follows:

5.

Press the MEMORY button to store the selection.

-14-

6.

Repeat steps 4 and 5 to store additional radio stations in memory.

TIMER OPERATION

To set the wake-up timer

1.

Press the power button to turn the unit off “STANDBY”

Press MODE / REMAIN button. The TIMER ON indicator appears on the LCD and flashes. Press MEMORY button the hour segment flashes.

6.

Press the CD-TUNING-SKIP button to select the timer-off hour.

7.

Press the MEMORY button again. The hour segment stops flashing, the minute segment flashes.

2.

3.

Press the CD-TUNING-SKIP button to select the wake-up hour.

Press the MEMORY button again. The hour segment stops flashing, the segment flashes.

4.

Press the CD-TUNING-SKIP button to select the wake-up minute.

5.

Press the MODE / REMAIN button once. The TIMER OFF indicator appears and flashing on the LCD. Press MEMORY button the hour segment flashes.

8.

Press the CD-TUNING-SKIP button to select the timer-off minute.

9.

Press the MEMORY button to conclude the setting process.

Press MODE / REMAIN button for “Timer Check” readout appears the “on” and “off” timers on the LCD.

10.

Press TIMER button once for timer operation. To disable timer operation, press the TIMER button again. On and off settings will still be kept in memory for future occasions when timer operation is desired. (Press the TIMER button again to activate.)

NOTE: The timer will turn on the function last used as follows:

Previously selected radio station

CD - track 1

-15-

TIMER OPERATION

SureWake function

This feature lets you adjust the night-time listening volume as low or high as desired without affecting the wake-up volume. In the morning, SureWake starts the music quietly and then increases it to room-filling volume to make sure you are awake.

1.

2.

3.

Activate the timer as described in the previous section.

Press down the SUREWAKE button, “SUREWAKE” displays on

LCD.

To de-activate SureWake, press to release the button.

Sleep-to-music function

1.

Press the SLEEP button and the LCD displays:

VOLUME CONTROL

Turn the VOLUME knob to get a satisfactory sound level when you select the desired program.

In SUREWAKE mode, within 10 seconds the volume will gradually increase to a room-filling level. After that, use the

VOLUME knob on the unit or the remote control to set the volume as desired.

Snooze Function

When the system turns on at the preset time, you can turn off the sound temporarily by pressing the SNOOZE button.

The sound will come on again after 5 minutes.

Note: The SNOOZE function can be activated at anytime. If you activate the snooze function accidentally, you can restore normal operation by turning the power off, then on again.

The system will remain on for 90 minutes, then turn off automatically.

2.

To decrease the time in 10-minute-increments, press the

SLEEP button and hold until the desired time appears.

3.

The SLEEP time will keep about 3 seconds, then go back to original display.

-16-

TROUBLESHOOTING

Before requesting service, check the chart below for a possible cause of the problem you are experiencing. Some simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation.

If you are in doubt about some of the check points, or if the remedies indicated in the chart do not solve the problem, please consult your dealer for instruction.

Problem Checkpoint Remedy

No operation 1. Is the AC plug connected?

Are the batteries dead?

2. Is the desired mode selected?

3. Is the disc inserted correctly?

Is the compartment closed?

4. Is the CD lens dirty?

1. Reconnect the AC plug or reinstall the batteries

properly. Change the batteries.

2. Press the desired function button.

3. Insert the disc correctly and close the compartment

lid securely.

4. Clean the CD lens or tape heads.

No display

No sound

Is the AC plug connected?

Are fresh batteries installed?

1. Are the speakers connected?

2. Is the headphone plugged in firmly?

3. Is the Snooze function activated?

Reconnect the AC plug or replace the batteries.

1. Check the speaker connections.

2. Insert the headphone plug into the phone jack firmly.

3. Turn the power off, then on again.

N o i s e o r w e a k radio reception

Is the FM antenna connected?

Rotate the unit for better reception (AM), move the FM antenna wire for better reception (FM)

Volume goes up

Automatically

Is the Sure Wake function off?

Make sure the Sure Wake appears on the LCD

See page 16.

-17-

SPECIFICATIONS

FM Frequency Range

AM Frequency Range

Power Supply (Main Unit)

Power Supply (Remote Control)

87.5MHz~108MHz / 50kHz Step

522kHz~1611kHz / 9kHz Step

AC230V, 50Hz

DC 12V (UM2 x 8PCS)

DC 3V (UM3 x 2PCS)

Instructions on environment protection

DENVER ELECTRONICS

Do not dispose of this product in the usual household garbage at the end of its lifecycle; hand it over at a collection point for the recycling of electrical and electronic appliances. The symbol on the product, the instructions for use or the packing will inform about the methods for disposal.

The materials are recyclable as mentioned in this marking. By recycling, material recycling or other forms of re-utilization of old appliances, you are making an important contribution to protect our environment.

Please inquire at the community administration for the authorized disposal location.

ALL RIGHTS RESERVED

COPY RIGHT DENVER ELECTRONIC A/S

WWW.denver-electronics.com

18