Miele DGC 6800 Product specifications

Installation Instructions
IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE
Information is subject to change. Please refer to our website to obtain the most
current product specification, technical & warranty information.
DGC 6700
DGC 6800
To prevent accidents
and appliance damage
read these instructions
before
installation or use.
IMPORTANT SAFETY INSTRUCTIONS
,WARNING - Read all instructions
before installation or use of the
steam oven to prevent injury and
machine damage.
~ Before installation make sure that
the voltage and frequency listed on the
data plate correspond with the
household electrical supply. This data
must correspond to prevent injury and
machine damage. Consult a qualified
electrician if in doubt.
~ Be certain your appliance is
properly installed and grounded by a
qualified technician. To guarantee the
electrical safety of this appliance,
continuity must exist between the
appliance and an effective grounding
system. It is imperative that this basic
safety requirement be met. If there is
any doubt, have the electrical system of
the house checked by a qualified
electrician.
~ Installation, repair and maintenance
work should be performed by a Miele
authorized service technician. Work by
unqualified persons could be
dangerous and may void the warranty.
Note to the installer:
~ Do not operate any appliance with a
damaged cord or plug or if the
appliance has been damaged in any
manner. Return the appliance to the
nearest authorized service facility for
examination, repair or adjustment.
SAVE THESE
INSTRUCTIONS
~ Make sure that the outlet is easily
accessible after installing the
appliance.
~ This appliance is not to be used in
mobile installations, such as ships.
~ The appliance must be placed so
that the content of the cooking pan on
the top shelf level can be seen. Only in
this way can scalding from spilling hot
food and hot water be avoided.
150
Please leave these instructions with the
consumer of the appliance for the local
building inspectors use.
Installation reference
Dimension details of the appliance front
* Appliances with glass front
** Appliances with metal front
151
Installation reference
Control panel swivel range
152
The area in front of the control panel
must not be blocked by anything (such
as a door handle) this would hinder the
control panel from opening and closing.
Appliance and installation dimensions
Wall cabinet installation
a Combi Steam Oven
b Installation niche
c Power supply to the appliance
d Recommended location for electrical connection
e Power cord
* Appliances with glass front
** Appliances with metal front
153
Appliance and installation dimensions
Cut-outs for venting the Combi Steam Oven
To ensure that the Combi Steam Oven has adequate ventilation, the following
cut-outs measuring 19 11/16" x 1 9/16" (500 x 40 mm) must be made:
a in the top of the cabinet
b in the center shelf above the installation niche
The cabinet housing must not have a back panel fitted behind the installation
niche.
154
Appliance and installation dimensions
Undercounter installation
If the appliance is to be installed under a cooktop, observe the instructions for
installation of the cooktop and its installation height.
a Combi Steam Oven
b Installation niche
c Power supply to the appliance
d Recommended location for electrical connection
e Power cord
* Appliances with glass front
** Appliances with metal front
155
Appliance and installation dimensions
Cut-outs for venting the Combi Steam Oven
To ensure that the Combi Steam Oven has adequate ventilation, the following
cut-outs measuring 19 11/16" x 1 9/16" (500 x 40 mm) must be made:
a in the appliance support base
b in the bottom of the cabinet space below
The cabinet housing must not have a back panel fitted behind the installation
niche.
156
Appliance and installation dimensions
Installation in combination with an oven
a Combi Steam Oven
b Installation niche
c Power supply to the appliance
d Recommended location for electrical connection
e Power cord
f Oven
* Appliances with glass front
** Appliances with metal front
157
Appliance and installation dimensions
Cut-outs for venting the Combi Steam Oven
To ensure that the Combi Steam Oven has adequate ventilation, the following
cut-outs measuring 19 11/16" x 1 9/16" (500 x 40 mm) must be made:
a in the top of the cabinet
b in the center shelf above the installation niche
The cabinet housing must not have a back panel fitted behind the installation
niche.
Cut-out for venting the oven:
Please refer to the installation instructions for the oven.
158
Appliance and installation dimensions
Installation in combination with ESW 6x14
a Combi Steam Oven
b Installation niche
c Power supply to the appliance
d Recommended location for electrical connection
e Power cord
f Warming drawer
* Appliances with glass front
** Appliances with metal front
159
Appliance and installation dimensions
Cut-outs for venting the Combi Steam Oven
To ensure that the Combi Steam Oven has adequate ventilation, the following
cut-outs measuring 19 11/16" x 1 9/16" (500 x 40 mm) must be made:
a in the top of the cabinet
b in the center shelf above the installation niche
The cabinet housing must not have a back panel fitted behind the installation
niche.
160
Installing the appliance
^ Push the appliance into the installation niche and align it.
The appliance must be level, so that the steam generator
can operate properly.
Deviation from the horizontal should not exceed 2°.
^ Secure the appliance to the left and right side of the
cabinet with the two supplied 1/8" x 1" (3.5 x 25 mm) wood
screws.
161
Electrical connection
,CAUTION: Before installation or
servicing, disconnect the power
supply by either removing the fuse,
shutting off the main power or
manually "tripping" the circuit
breaker.
Installation work and repairs should
only be performed by a qualified
technician in accordance with all
applicable codes and standards.
Repairs and service by unqualified
persons could be dangerous.
Before connecting the appliance to
the power supply, make sure that
the voltage and frequency listed on
the rating label correspond with the
household electrical supply. This
data must correspond to prevent
appliance damage.
Only operate the appliance after it
has been installed.
If there is any question concerning
the electrical connection of this
appliance to your power supply,
please consult a licensed electrician
or contact Miele’s Technical Service
Department.
Installer:
Please leave these instructions with
the consumer.
162
Power supply
Installation, repairs and other work
by unqualified persons could be
dangerous.
^ Be sure your electrical supply
matches the data plate.
Power supply
This appliance is equipped with a 5 ft
(1.5 m) long power cord with a
three-prong grounding plug ready for
connection to a 240 V, 20 A, 60 Hz
power supply.
Further installation details are on the
wiring diagram.
(NEMA 6-20P, 20 amp, 240 VAC,
L1, L2, G)
After sales service
In the event of a fault which you cannot
correct yourself please contact the
Miele Technical Service Department at
the phone numbers listed on the back
of this booklet.
When contacting the Technical Service
Department, please quote the model
and serial number of your appliance.
These are shown on the data plate.
MieleCare
(USA only)
MieleCare, our Extended Service
Contract program, gives you the
assurance of knowing that your
appliance investment is covered by
5 years of worry free ownership.
MieleCare is the only Extended Service
Contract in the industry that guarantees
repairs by a Miele Authorized Service
Provider using genuine Miele parts.
Only genuine Miele parts installed by
factory trained professionals can
guarantee the safety, reliability, and
longevity of your Miele appliance.
Please note that unless expressly
approved in writing by Miele’s Service
department, Extended Service
Contracts offered by other providers for
Miele products will not be recognized
by Miele. Our goal is to prevent
unauthorized (and untrained) service
personnel from working on your Miele
products, possibly doing further
damage to them, you and/or your
home.
To learn more about MieleCare
Extended Service Contracts, please
contact your appliance dealer or visit
us online at:
http://mieleusa.com/mielecare
163
Copyrights and Licenses
For the operation and control of the appliance, Miele uses software.
The copyright powers of Miele and other software vendors concerned (e.g.
Adobe) are to be respected.
Miele and its suppliers reserve all rights to the software components.
Specifically prohibited are:
– Reproduction and distribution,
– Production of changes and derived items,
– Decompilation, reverse engineering, disassembly and otherwise reducing the
software.
This product contains Adobe® Flash® Player software under license from Adobe
Systems Incorporated, Adobe Macromedia Software LLC. Adobe and Flash are
registered trademarks of Adobe Systems Incorporated.
The software also contains integrated components covered under the GNU
General Public License and other Open Source Licenses.
You can obtain an overview of the integrated open source components together
with a copy of the license at www.miele.com/device-software-license_en after
entering your specific product name.
Miele submits the source code for all components under the GNU General Public
License and similar Open Source Licenses licensed software.
To obtain such a source code, please send an e-mail to info|miele.com.
164
Caring for our environment
Disposal of packing material
Disposal of an old appliance
The transport and protective packing
materials are environmentally friendly
for disposal and may be recyclable.
Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibility of recycling these materials.
Ensure that any plastic wrap is
disposed of safely and kept out of the
reach of children. Danger of
suffocation! Danger of suffocation!
Before discarding an old appliance
ensure that it presents no danger to
children while being stored for
disposal. Unplug it from the outlet, cut
off its power cord and remove any
doors to prevent hazards.
165
166
INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE
TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL
& WARRANTY INFORMATION.
167
DGC 6700 / DGC 6800
en - US, CA
M.-Nr. 09 855 050 / 01